cx24
TRANSCRIPT
SERVICE NOTES
Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.Copyright © 2003 ROLAND DG CORPORATION
CX-24 / 12
5016-06Printed in Japan
Structure & Spare Parts
Electrical Section
Replacement of Main Parts
Adjustment
Supplemental Information
Trouble Shooting
Supplement
1
2
3
4
5
6
7
Seventh EditionCX-24/12 '03.Feb.
1 Structure & Spare Parts1-1 COVERS ................................................................................... 1-11-2 FRAME ...................................................................................... 1-21-3 CARRIAGE ............................................................................... 1-41-4 CHASSIS .................................................................................. 1-51-5 ACCESSORIES ........................................................................ 1-61-6 STAND PNS-24 ........................................................................ 1-61-2 Electrical Section2-1 WIRING MAP ............................................................................ 2-12-2 MAIN BOARD ............................................................................ 2-22-3 OTHER CIRCUIT BOARDS ...................................................... 2-4
3 Replacement of Main Parts3-1 TOOL CARRIAGE_REPLACEMENT ........................................ 3-13-2 MAIN BOARD_REPLACEMENT ............................................... 3-83-3 CARRIAGE MOTOR_REPLACEMENT ................................... 3-113-4 GRIT MOTOR_REPLACEMENT ............................................. 3-143-5 PINCH ROLLER_REPLACEMENT .......................................... 3-183-6 CUTTER PROTECTION_REPLACEMENT ............................. 3-19
4 Adjustment4-1 Special Tool .............................................................................. 4-14-2 Service Mode ............................................................................ 4-24-3 Function Mode ........................................................................... 4-44-4 HOW TO UPGRADE FIRMWARE ............................................ 4-54-5 TOOL HEIGHT ADJUSTMENT ................................................. 4-64-6 TOOL PRESSURE ADJUSTMENT .......................................... 4-94-7 CALIBRATION ......................................................................... 4-12
4-8 CROP MARK SENSOR CHECK .............................................. 4-164-9 AUTO CROP MARK SENSOR ADJUSTMENT ....................... 4-184-10 MANUAL CROP MARK SENSOR ADJUSTMENT .................. 4-20
5 Supplemental Information5-1 OPERATIONAL SEQUENCE ................................................... 5-15-2 SENSOR MAP .......................................................................... 5-2
6 Trouble Shooting6-1 START & END POINTS DONÕT MATCH ................................ 6-16-2 STITCH CUT ............................................................................. 6-36-3 MEDIA SHIFTING ..................................................................... 6-46-4 PEN UP/DOWN ERROR .......................................................... 6-56-5 FAN REVOLUTION ................................................................... 6-6
7 Supplement7-1 INSTALLATION CHECK LISTMAINTENANCE CHECK LIST .. 7-17-2 MAINTENANCE CHECK LIST .................................................. 7-57-3 SPECIFICATIONS .................................................................... 7-6
Contents
Windows is registered trademark or trademark of Microsoft¨ Corporation in the United States and/or other countries.
Revision RecordRevision
No. Date Description of Changes Approval Issued by
0 2000.08.01 First Edition Inagaki Kaneko
1 2000.09.13 3-6 (p.29) CUTTER PROTECTION REPLACEMENT Inagaki Kaneko
2 2000.10.17 4-2, 4-3 Additional : Tool Pressure Control Command !FS Inagaki Kaneko
3 2001.01.15 1-2 Parts List : L-BEARING,RSR9ZMUUC1 Inagaki Kaneko
1-3 Parts List : STAY,CARRIAGE
4 2003.02.13 CROP MARK Sensor has been added. Inagaki Nakatani1-3 Parts List : STAY,CARRIAGE
2-1 WIRING MAP
3-1 TOOL CARRIAGE_REPLACEMENT
4-2 Service Mode
4-8 CROP MARK SENSOR CHECK
4-9 AUTO CROP MARK SENSOR ADJUSTMENT
4-10 MANUAL CROP MARK SENSOR ADJUSTMENT
5-1 OPERATIONAL SEQUENCE
5-2 SENSOR MAP
5 2003.02.18 1-3 CX-24 Serial Number for Crop Mark Sensor Inagaki Nakatani
6 2003.02.25 1-3 CX-24 Serial Number for Crop Mark Sensor Inagaki Nakatani
To Ensure Safe Work
To Ensure Safe WorkAbout WARNING and CAUTION Notices
Used for instructions intended to alert the operator to the risk of death orsevere injury should the unit be used improperly.
Used for instructions intended to alert the operator to the risk of injury ormaterial damage should the unit be used improperly.* Material damage refers to damage or other adverse effects caused with
respect to the home and all its furnishings, as well to domestic animals orpets.
About the Symbols
The symbol alerts the user to items that must never be carried out (are forbidden). Thespecific thing that must not be done is indicated by the design contained within the circle.The symbol at left means not to touch.
The symbol alerts the user to things that must be carried out. The specific thing thatmust be done is indicated by the design contained within the circle. The symbol at leftmeans the power-cord plug must be unplugged from the outlet.
Turn off the power SW beforeservicing.
The symbol alerts the user to important instructions or warnings. The specific meaningof the symbol is determined by the design contained within the triangle. The symbol at leftmeans "danger of electrocution."
WARNING
CAUTION
WARNING
-- MEMO --
1 Structure & Spare Parts
1-1
1
PARTS LIST -Main Parts-Parts No. Parts Name
1 22805381 ASS'Y,LCD CX-24 * *22025409 COVER,FRONT CX-12 *22025408 COVER,FRONT CX-24 *22025428 COVER,GUIDE R2 CX-12 *22025427 COVER,GUIDE R2 CX-24 *
4 22025406 COVER,SIDE L CX-24 * *5 22025407 COVER,SIDE R CX-24 * *
22025411 COVER,Y RAIL CX-12 *22025410 COVER,Y RAIL CX-24 *
7 22495206 KEY TOP,CX-24 * *8 22475108 KNOB,CX-24 * *
9 22535235 LABEL,CORPORATE LOGOTYPE#LA97 * *
10 7501623020 PANEL BOARD ASS'Y * *11 12259222 SHIELD,E01S03-1YAMA *12 22255221 SHIELD,PANEL R CX-24 * *13 21395112 TAPE,FELT CX-24 *
2
3
6
1 Structure & Spare Parts1-1 COVERS
4
63
5
1
10
12
11
78
2
9
13
S1
S1
S4
S4
S4S4
S4
S4
S4
S1
S1
S5
S5
S2
S3
S3
CX-12
CX-24
PARTS LIST -Supplemental Parts-Parts Name
S1 SCREW,BINDING HEAD M4x5 NiS2 SCREW,BINDING HEAD P-TIGHT M3x6BCS3 SCREW,BINDING HEAD P-TIGHT M3x8CS4 SCREW,BINDING HEAD WITH TEETH WASHER M3x8NiS5 SCREW,W-SEMS M3x8BC
1-2
1 Structure & Spare Parts
1S
12
S12 18
S8
S17
S7
S8 S8
15
26S
6
S15
42
54
4210
53
S6 S15
10
S9
41 S19
S15 38
26
25
1513
S10
11S
22S
8
S8
S7
S2
S8
2
S8
828
4832S
11
344436
5555 31
21
24S
18
S16
476
12
2940
39
S20
S21
51S
6S
17
S1533
S8
5217
22
46
S3 9
S7
14
S6 49
204537
S1
S1
S13
16
3
S8 12
35S
14
S5
27
30
S5
S14
35 S5
S5
27
30
43
S4
8
3
23
1-2 FRAME
1 Structure & Spare Parts
1-3
1
CX-
12CX-
24C
X-12C
X-24
Rev
ised
3
PART
S LI
ST- M
ain
Part
s-Pa
rts N
o.Pa
rts N
ame
122
8053
83AS
S'Y,
FRAM
E L
CX-
24*
*2
2280
5382
ASS'
Y,FR
AME
R C
X-24
**
322
8053
80AS
S'Y,
PIN
CH
RO
LLER
CX-
24*
*5
2280
5145
ASSY
,MO
TOR
X P
NC
-960
**
622
8051
44AS
SY,M
OTO
R Y
PN
C-9
60*
*11
9291
16BE
LT,1
526P
2M6
*11
9291
17BE
LT,9
40P2
M6
*8
1215
9508
BUSH
,SH
AFT
OIL
ES 8
0F-1
206
**
975
0162
3060
CAB
LE C
LAM
P*
*10
2350
5639
CAB
LE-A
SSY
PPSE
NSO
R C
X-24
*22
0254
75C
OVE
R,U
ND
ER F
.C C
X-12
*22
0254
76C
OVE
R,U
ND
ER F
.C C
X-24
*12
2226
5295
CU
SHIO
N*
*13
1171
9107
FAN
,109
BD24
HA2
-2*
*22
1157
88FR
AME,
CAB
LE C
X-12
*22
1157
83FR
AME,
CAB
LE C
X-24
*22
1157
86FR
AME,
CEN
TER
CX-
12*
2211
5781
FRAM
E,C
ENTE
R C
X-24
*22
1157
89FR
AME,
GU
IDE
CX-
12*
2211
5784
FRAM
E,G
UID
E C
X-24
*22
1157
85FR
AME,
SUPP
OR
T C
X-12
*22
1157
80FR
AME,
SUPP
OR
T C
X-24
*18
2217
5693
GEA
R L
**
1921
6551
63H
OLD
ER,B
ELT
CX-
24*
*20
2165
5164
HO
LDER
,IDLE
PU
LLEY
CX-
24*
*21
2248
5105
KNO
B,LE
VER
CX-
24*
*L-
BEAR
ING
,RSR
9NM
UU
C1+
380L
M(C
X-12
: Z
O00
382
and
belo
w)
L-BE
ARIN
G,R
SR9Z
MU
UC
1+38
0LM
(CX-
12 :
ZO00
383
and
abov
e )
L-BE
ARIN
G,R
SR9N
MU
UC
1+68
0LM
(CX-
24 :
ZO02
864
and
belo
w)
L-BE
ARIN
G,R
SR9Z
MU
UC
1+68
0LM
(CX-
24 :
ZO00
2865
and
abo
ve)
2253
5234
LABE
L,G
-RO
LLER
CX-
12 #
LA96
*22
5352
32LA
BEL,
G-R
OLL
ER C
X-24
#LA
170
*
2189
5102
2189
5134
2189
5103
2189
5135
*
*
16 17 23227 11 14 15
PART
S LI
ST
-Sup
plem
enta
l Par
ts-
Parts
Nam
eS1
BUSH
,RO
LL3x
5S2
EDG
E SA
DD
LEED
S-3
S3LI
VET,
PUSH
NYL
ON
P355
0S4
RIN
G,E
ETW
-10
SUS
S5R
ING
,EET
W-3
SU
S
S6SC
REW
,BIN
DIN
G H
EAD
M3x
6 C
S7SC
REW
,BIN
DIN
G H
EAD
WIT
HTE
ETH
WAS
HER
M3x
8 N
i
S8SC
REW
,BIN
DIN
G H
EAD
WIT
HTE
ETH
WAS
HER
M4x
6 N
i
S9SC
REW
,FLA
T H
EAD
M3x
10BC
S10
SCR
EW,H
EXAG
ON
SO
CKE
TH
EAD
CAP
M4x
35 B
C
S11
SCR
EW,H
EXAG
ON
SO
CKE
TH
EAD
CAP
PR
ECO
ATIN
G L
OC
KAG
ENT
M3x
8 BC
S12
SCR
EW,H
EXAG
ON
SO
CKE
T SE
TM
3x3
BC
S13
SCR
EW,P
ANH
EAD
M3x
6 N
iS1
4SC
REW
,TR
USS
HEA
DM
2x5
BCS1
5SC
REW
,W-S
EMS
M3x
6 N
iS1
6SC
REW
,W-S
EMS
M4x
10 B
C
S17
SCR
EW,W
-SEM
S PR
ECO
ATIN
GLO
CK
AGEN
TM
3x8
C
S18
SCR
EW,W
-SEM
S PR
ECO
ATIN
GLO
CK
AGEN
TM
4x15
BC
S19
WAS
HER
,PLA
NE
3x6x
0.5C
S20
WAS
HER
,PLA
NE
4.3x
7x1C
S21
RIN
G,C
SC
S-4
S22
LIVE
T,PU
SH N
YLO
NP2
655B
PART
S LI
ST-M
ain
Part
s-Pa
rts N
o.Pa
rts N
ame
2422
1454
46LE
VER
,HAN
DLE
CX-
24*
*22
2651
01PA
D C
UTT
ER*
2154
5133
PAD
,CU
TTER
CM
-12
*26
2263
5376
PAD
,DU
CT
CX-
24*
2722
1458
31PI
N N
O.1
(2
14-8
31)
**
2821
5351
18PI
N,S
TOPP
ER G
-LEV
ER P
C-6
0*
*29
2153
5101
PIN
,Y P
ULL
EY P
NC
-500
0*
*30
2217
5877
PIN
CH
RO
LLER
(WH
EEL
RO
LLER
)*
*31
2205
5462
PLAT
E,AX
IS C
X-24
**
3222
0554
60PL
ATE,
LIN
K C
X-24
**
3322
0554
09PL
ATE,
OR
G C
X-24
**
3422
0554
59PL
ATE,
OSC
ILLA
TE C
X-24
**
3522
0554
61PL
ATE,
SEN
SOR
CX-
24*
*36
2205
5458
PLAT
E,SP
ACER
CX-
24*
*37
2217
5715
PULL
EY H
D10
.8S3
(B9)
**
3822
1451
07SZ
BAC
K U
P ST
AY*
*39
2197
5105
PULL
EY T
20P2
S8+G
EAR
S55
**
4011
8891
02R
-BEA
RIN
G D
8S4(
B3)
**
4122
1758
71R
OLL
ER F
D12
S4(
B4 C
4.0)
*42
1522
9505
SEN
SOR
INTE
RR
UPT
ER G
P2A2
5*
2229
5194
SHAF
T,G
RO
LLER
CX-
12*
2229
5101
SHAF
T,W
ITH
G-R
OLL
ER P
NC
-960
*44
2214
5393
SHAF
T,JO
INT
PNC
-960
**
4522
1453
88SH
AFT,
PULL
EY P
NC
-960
**
2229
5196
SHAF
T,SQ
UAR
E C
X-12
*22
2951
97SH
AFT,
SQU
ARE
CX-
24*
4722
1651
64SP
ACER
,MO
TOR
CX-
24*
*48
2217
5157
SPR
ING
,C P
-RO
LLER
CM
-500
**
4922
1751
88SP
RIN
G,T
ENSI
ON
CX-
24*
*50
2271
5215
STAY
,CAR
RIA
GE
CX-
24*
*51
2271
5219
STAY
,DR
IVE
SHAF
T C
X-24
**
5222
7152
17ST
AY,F
RAM
E G
UID
E C
X-24
**
5322
7152
20ST
AY,S
ENSO
R F
CX-
24*
5422
7152
56ST
AY,S
ENSO
R R
CX-
24*
5521
4251
15W
ASH
ER,A
XIS
CX-
24*
*
25 43 46
1-4
1 Structure & Spare Parts
1
PARTS LIST -Main Parts-
Parts No. Parts Name1 21815101 BOLT,PENHOLDER * *
23475166 CABLE-CARD 8P 1030L BB HIGH-V *23475165 CABLE-CARD 8P 730L BB HIGH-V *
3 22805393 CARRIAGE ASS'Y CX-24 * *4 7501623040 CARRIAGE JUNCTION BOARD ASS'Y * *5 22025404 COVER,CARRIAGE CX-24 * *6 21655163 HOLDER,BELT CX-24 * *7 21655162 HOLDER,SENSOR BOARD CX-24 * *8 7501625000 MARK SENSOR BOARD ASS'Y * *9 22285503 NUT,PENHOLDER * *10 7501623030 PINCH SENSOR BOARD ASS'Y * *11 22155567 SPACER M3X5 * *12 22165198 SPACER,SENSOR CX-24 * *13 22715216 STAY,CABLE CX-24 * *14 22715265 STAY,CARRIAGE-2 CX-24 * *15 22715255 STAY,MARK SENSOR CX-24 * *
11929116 BELT,1526P2M6 *11929117 BELT,940P2M6 *
2
16
1-3 CARRIAGE2
S2
S3
S3S4
S8
S8
4
13
S7
1
9
5
S8
S5
S1
15
12
8
S6
S7
3
11
S8
S10
6
14
S11
10
7
S9
S1
S12
16
S12
CX-12
CX-24
Revised 3
Revised 3
Revised 3
Revised 3
Revised 4
CROP MARK SENSOR has been fixed to themachines with the following serial number.CX-24 : AQ87825 and aboveCX-12 : ZQ81680 and above
PARTS LIST -Supplemental Parts-
Parts No. Parts Name remarksS1 31379106 CLAMP,MINI MB-2 *20 pcs./setS2 31329601 CLAMP,INSULOK T-18S *100 pcs./setS3 31159110 CUSHION,GREEN FELT 3T*8*840 **cut off 14mmS4 31409702 SADDLE,LOCKING EDGE LES-1010 *20 pcs./setS5 31089103 SCREW,PAN M2.6*4 C *100 pcs./setS6 31229103 SCREW,TRUSS M2*6 BC *100 pcs./setS7 31239128 SCREW,W-SEMS M3*8 NI *100 pcs./setS8 31239127 SCREW,W-SEMS M3*6 NI *100 pcs./setS9 31679102 SCREW,C-SEMS M3*5.5 NIS10 31019103 SCREW,BINDING M3*6 C *100 pcs./setS11 31019701 SCREW,BINDING P-TIGHT 3*8 C *100 pcs./setS12 31019148 SCREW,BINDING M2.6*4 C *100 pcs./set * : These parts will be provided as set per quantity in remarks with P/N+AS.** : This part will be provided by roll. Please cut when using.
Revised 3
Revised 3Revised 3
Revised 4
Revised 4
Revised 4
Revised 4
Revised 4
Revised 3
Revised 5Revised 6
1 Structure & Spare Parts
1-5
1
PARTS LIST -Main Parts-
Parts No. Parts Name1 13429746 AC INLET SUP-J3G-E+FILTER * *2 23505674 CABLE-ASSY JUNBI A CX-24 * *3 23505675 CABLE-ASSY JUNBI B CX-24 * *
23505634 CABLE-ASSY JUNBI D PC-600 *23505419 CABLE-ASSY JUNBIWIRE D FJ-50 *
5 23505640 CABLE-ASSY POWER 2 CX-24 * *6 23475125 CABLE-CARD 25P 150L BB HIGH-V * *
22815138 CHASSIS,CX-12 *22815137 CHASSIS,CX-24 *
8 11769106 CLAMP,CLAMP-B * *9 22465129 HEAT-SINK,CX-24 * *10 22535257 LABEL,CAUTION VOLTAGE #LA167 * *11 22505242 LABEL,EARTH MARK-1 NO.E-580 * *12 22505244 LABEL,FLASH-LIGHTING NO.E-582 * *13 7501623010 MAIN BOARD ASS'Y CX-24 * *14 22055418 PLATE,F-COVER CX-24 * *15 13129170 POWER SW AJ7201B * *16 22425109U0 POWER UNIT,SWITCHING CX-24 * *17 22355168 RUBBER FOOT PL-10J65 * *18 23505899 WIRE,C GRX-410 * *
4
7
S1
S3
S6
18
2
3
1S4
154
14
14
14S3
S3
S3
17
17
S2S2
7
S5
16
5
13
9
S5
8S5
S5
6
S2
S210
12
11
1-4 CHASSIS
CX-12
CX-24
PARTS LIST -Supplemental Parts-Parts Name
S1 CABLE TYE,PUSHMOUNT PT30SSF5S2 CLAMP,WIRE LWS-0711ZS3 SCREW,BINDING HEAD M4x5NiS4 SCREW,FLAT HEAD M3x10BCS5 SCREW,W-SEMS M3x6NiS6 WASHER,TEETH M4
1-6
1 Structure & Spare Parts
1
PARTS LIST -Main Parts-Parts No. Parts Name
1 13499109 AC CORD SJT 117V 10A 3PVC * *2 23495124 AC CORD 3ASL/100 240VA 10A S * *3 13499111 AC CORD H05VV-F 240VE 10A S * *4 23495125 AC-CORD H05VV 230V 10A S * *5 13439801 CABLE-AC 3P CHINA 10A/250V S * *6 22355647 BASE,SHEET CM-24 * *
22605337 CARTON CX-12 *22605336 CARTON CX-24 *
8 22635379 PAD,SET CX-24 * *
7
1-5 ACCESSORIES
1-6 STAND PNS-24
8
6
7
1 2 3
4 5
CX-12
CX-24
5 6
1
3
4
CX-12
CX-24
2
PARTS LIST -Main Parts-
Parts No. Parts Name1 21985116 BRACKET,PNS-24 *2 22605279 CARTON,PNS-24 *3 22155121 PIPE,1 PNS-24 *4 22155122 PIPE,2 PNS-24 *5 22035126 STAND,L PNS-24 *6 22035127 STAND,R PNS-24 *
PARTS LIST -Supplemental Parts-
Parts NameS1 SCREW HEXAGONAL CAP UC 10X45S2 WASHER FLAT UC 10X21X2S3 CUSHION SK1912 RUBBERS4 BOLT PICK UC 5X20S5 TOOL HEXAGONAL NO.8S6 SHAFT STOPPER Ni 4.5X95
2 Electrical Section
2-1
2
2-1 WIRING MAP 2 Electrical Section
NL
F R
CG
MA
IN B
OA
RD
CN
7
CN
9
CN
6
CN
8
CN
4
CN
3
Fron
t Pap
er S
enso
r
Rea
r Pa
per
Sens
or
Blu
e
Yel
low
CA
BL
E-A
SSY
PPS
EN
SOR
CX
-24
2350
5639
CA
BL
E-A
SSY
PO
WE
R 2
CX
-24
2350
5640
CN
2
POW
ER
UN
IT,S
WIT
CH
ING
CG
676
2242
5109
U0
CN
1
Gri
t Mot
orC
arri
age
Mot
orFa
n
Blu
e
Bro
wnC
X-1
2 : C
AB
LE
-ASS
Y J
UN
BI
D P
C-6
0023
5056
34C
X-2
4 : C
AB
LE
-ASS
Y J
UN
BI
D F
J-50
2350
5419
CA
BL
E-C
AR
D 2
5P 1
50L
BB
HIG
H-V
2347
5125
CN
10
CN
12
CN
11
PAN
EL
BO
AR
D
LC
D
CX
-24
CA
BL
E-C
AR
D 8
P 10
30L
BB
HIG
H-V
2347
5166
CX
-12
CA
BL
E-C
AR
D 8
P 17
30L
BB
HIG
H-V
2347
5165
Sole
noid
Pinc
h Se
nsor
CN
13
CN
14C
N15
CN
16
CA
RR
IAG
E B
OA
RD
Mar
k Se
nsor
CA
BL
E-A
SSY
JU
NB
I A
CX
-24
2350
5674 CA
BL
E-A
SSY
JU
NB
I B
CX
-24
2350
5675
POW
ER
SW
AJ7
201B
1312
9170
AC
IN
LE
TSU
P-J3
G-E
1342
9746
Bro
wn
Blu
e
Gre
en/Y
ello
w
JUN
BI
C G
RX
-410
2350
5899
Rev
ised
4
2 Electrical Section
2-2
2
MA
IN B
OA
RD
MBM29F400BA
HD
6437
042
16M DRAM
74HC175
AD7305
5636
4-06
0-B
XE
Cab
le C
lam
p
74L
S245
74L
S14
74H
C12
3
74H
C37
374
HC
7474
LV
08A
7.17
5NH
z
74H
C13
8
MA
DE
IN
JA
PAN
53014-0510
53014-0410
R80
R81
MT
D20
05M
TD
2005
MT
D20
05
B4P
-VH
100u
/16v
47u/
50V
74H
C13
8
12
1 2
3
4
5
6
7
8
9
0
1
2
3 4
5
6
7
8
9
C
X-2
4/12
BL
02R
N2
BL
02R
N2
BL
02R
N2
BL
02R
N2
BL
02R
N2
BL
02R
N2
BL
02R
N2
BL
02R
N2
BL
02R
N2
BL
02R
N2
Grit
MA
X23
8CW
G
C30
114
R5
R55
SW
2
EC
16
B2
42
04
SW
6
EV
Q2
13
05
RE
VQ
21
30
5R
EV
Q2
13
05
RE
VQ
21
30
5R
EV
Q2
13
05
R
EV
Q2
13
05
R
EV
Q2
13
05
R
EV
Q2
13
05
R
EN
1
RA16EX
BA
10
E1
03
J
14
FP
Z-S
M-T
F
CN
12
74HC04
SW
5S
W1
SW
8
SW
7S
W3
SW
4
CP
45
IC2
7
R8
5
R8
6
R8
7
R8
4
IC25
CP4310
5
74
LS
24
5
MA
DE
IN JA
PAN
Carriage
CN
16C
N15
CN
14
CN13
IL-S2P-S2L
IL-FPC-8SL
Red B
lue
Whi
te
Bla
ckG
reen
MA
DE
IN J
APA
N
IC28
RA
2R
A1
RA
3D
1
CN
1
R43
19 136 18
C5
IC1
CP8
mon
itor
mod
el
ON S1
IC8
IC6
IC10 IC3
IC9
IC7C29 R76
Paper Sensor
x1
CN7
C3
C48R35
R38R18
R2
IC24
IC22
USB
uni
t
Non
Non
08
Mai
n
SubJP1
TP4
112
C42
TP3
IC5
RA
8T
P5
TP1TP2
TP6
IC16IC17
IC4
7516
2300
0 1
/5
RA
11
IC2
Vcc
93LC46
GND
C15
R4
IC14
C13
RA
9R
A10
C41
R45
R67
Vm
m
CN9
R83
IC21
R60
R59
C44 R
6IC
13
47u/
50V
C12
NJU
7032
C16
RA
4
RA
6
R69
IC20
R58
R73 C45
R28
R53
C22
R54
R29
C21
C19
R25
R52
R63
C23
C20
D8
D9
D10
D11 D2
D3
D4
D5
C11
47u/
50V
R75
R74
C46
R57
IC19
R3
C14C17
R24
R36
C47
R37
R23
C18
R56
FL24
FL27FL26FL25FL33FL32FL31
FL30
CN4 CN3
CN
8
to F
AN
Carriage to Motors
R61
IC51
D7
D6
Q2
D13
CN
5
RA
13R
A14
RA
15
X2
IC18
DB
LC
-J25
SAF-
20L
9
11425
3
CN
2
V-C
UT
LIN
E
FL23
FL21
FL19
FL17
FL15
FL13
FL29
C39
FL28
RA
12
C24 C25
IC23IC11
CN6
Blue5 15 25
10 20
R15 RA7RA5
C26
R13
R72
Q1
D12
C40
L1
R82
IC12
MA
DE
IN J
APA
N
2-2 MAIN BOARD MAIN BOARD COMPONENT DIAGRAM_COMPONENT SIDE
DIP SW
This Jumper SW should be set to the MAIN side.
No. Function OFF ON1 Model Selection CX-24 CX-122 Reserved ALWAYS OFF
Electric Maintenance PartIC.No. Parts No. Description Function
IC 12 15189105 MTD2005 Grit Motor DriverIC 13 15189105 MTD2005 Carriage Motor DriverIC 14 15189105 MTD2005 Solenoid Driver
2 Electrical Section
2-3
2
MAIN BOARD_Circuit Diagram
/RE
SE
T
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A[1
..18]D[0
..15]
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
R1
10K
C1 27
pC
2 27p
X1
7.17
5MH
z
CP
1 1u
CP
21u
CP
3N
onC
P4
Non
CP
5N
on
CP
61u
Vcc
1
Gnd
2ou
t3
IC1
PS
T57
2CM
T
R2
22K
R18
1KC
31u
SK
2C
S1
DI
3
VC
C8
DO
4
GN
D5
IC2
93LC
46
9108
IC3C
74LV
08A
A0
11
A1
10
A2
9
A3
8
A4
7
A5
6
A6
5
A7
4
A8
42
A9
41
A10
40
A11
39
A12
38
A13
37
A14
36
A15
35
A16
34
A17
3
D0
15
D1
17
D2
19
D3
21
D4
24
D5
26
D6
28
D7
30
D8
16
D9
18
D10
20
D11
22
D12
25
D13
27
D14
29
D15
31
VCC23
Vss13
CE
12
OE
14R
ES
ET
44
Vss32
WE
43
RY
/BY
2
BY
TE
33
IC4
MB
M29
F40
0BA
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
JP1
DS
P03
-003
-432
T
MA
INS
UB
R35
10K
R38
220K
D0
70D
169
D2
68D
367
D4
66D
564
D6
63D
762
D8
60D
959
D10
58D
1157
D12
56D
1354
D14
53D
1552
CS
041
CS
140
CS
245
CS
344
RD
/WR
28
RD
34
RA
S24
CA
SL
25
CA
SH
26
WR
H36
WR
L38
PF
0/A
N0
91
PF
1/A
N1
92
PF
2/A
N2
93
PF
3/A
N3
94
PF
4/A
N4
95
PF
5/A
N5
96
NM
I76
TC
LKD
42T
CLK
C43
A0
4
A1
5
A2
6
A3
7
A4
8
A5
9
A6
10
A7
11
A8
12
A9
13
A10
14
A11
15
A12
16
A13
17
A14
18
A15
19
A16
20
A17
22
A18
29
RE
SE
T84
PLL
CA
P81
PLL
VC
C80
PLL
VS
S82
XT
AL
72
EX
TA
L74
PA
15/C
LK83
MD079MD1
78 MD275
MD373
WD
TO
VF
35
Vss27
RX
D0
51
TX
D0
50
Vcc21
Vcc37
Vcc65
Vcc77
Vcc103
Vss3
Vss 23
Vss33
Vss 39
Vss55
Vss 61
Vss71
Vss90
Vss 101
Vss109
RX
D1
48
TX
D1
47
PE
1311
2
PE
710
5
PE
8(T
IOC
3A)
106
PE
1211
1
PF
6/A
N6
98
PF
7/A
N7
99
PE
5(T
IOC
1B)
102
PE
9(T
IOC
3B)
107
PE
10(T
IOC
3C)10
8
PE
11(T
IOC
3D)
110
PE
141
PE
152
AV
CC
100
AV
SS
97
PB
831
PB
932
PA
5(D
SR
)46
PA
2(R
TS
)49
PE
4(D
TR
)89
DR
EQ
085
PE
186
DR
EQ
187
PE
388
IRQ
530
PE
610
4
IC5
HD
6437
042
Vcc
Vcc
R15
0
A1A2A3A4A5A6A7A8A9A10
CP
7
1u
CP
8
1u
C4
470p
R39
3.3K R
46 220
CP
91u
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
46
5 IC3B
74LV
08A
56
IC6C
74LS
14
1312
IC6F
74LS
14
/CR
D
/CR
DY
D0
D1
D2
D3
D4
D5
D6
D7
BU
SY
/AC
K
DA
TA
0D
AT
A1
DA
TA
2D
AT
A3
DA
TA
4D
AT
A5
DA
TA
6D
AT
A7
/ST
BV
cc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
D2
3
D4
4
D6
7
D8
8D
713
D5
14
D3
17
D1
18
OC
1
G11
Q2
2
Q4
5
Q5
6
Q7
9Q
612
Q5
15
Q3
16
Q1
19
Vcc20
GND10
IC7
74H
C37
3
R47
33
R48
33
R20
1KR
211K
R40
3.3K
R50
3.3K
R41
3.3K
R42
3.3K
1 2 3 4 5678910
RA
1
10K
x8
81
72
63
54
RA
2
33x4
81
72
63
54
RA
3
33x4
A1
2
A2
3
A3
4
A4
5
A5
6
A6
7
A7
8
A8
9
G19
DIR
1
B1
18
B2
17
B3
16
B4
15
B5
14
B6
13
B7
12
B8
11
Vcc20
GND10
IC874
LS24
5
D1
D1F
L20U
R22
1K
R49
33
12
IC6A
74LS
14
34
IC6B
74LS
14
C5
1000
p
R43
3.3K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
E1E2
CN
156
364-
060-
BX
ED
2
CLK
3
Q5
Q6
Vcc
14P
R4
GN
D7
CL
1
IC9A
74H
C74
D12
CLK
11
Q9
Q8
PR
10
CL
13
IC9B
74H
C74
extC
14
extC
R15
A1
B2
CLR
3
Q13
Q4
Vcc
16
GN
D8
IC10
A74
HC
123
123
IC3A
74LV
08A
FL1
FL2
FL3
FL4
FL5
FL6
FL7
FL8
FL9
FL1
0
EX
C3B
B60
1H FL1
1
CD
0C
D1
CD
2C
D3
CD
4C
D5
CD
6C
D7
1110
IC6E
74LS
14
98
IC6D
74LS
14
Vcc
TX
DA
RX
DA
/RT
SA
RX
DB
/DT
RA
/DS
RA
TX
DB
Vcc
C1+
10
C1-
12
C2+
13
C2-
14
V+
11
V-
15
out
2
in7
out
1
in3
out
24
in23
out
20
in16
in5
out
6
in18
out
4
in19
out
22
in21
out
17
VC
C9
GN
D8
T1
T2
T3
T4
R1
R2
R3
R4
IC11
MA
X23
8
13251224112310229218207196185174163152141
E1 E2
CN
2D
BLC
-J25
SA
F-2
0L9
extC
6
extC
R7
A9
B10
CLR
11
Q5
Q12
IC10
B
74H
C12
3
Vcc
CP
10
1u Vm
m
Vcc
Vcc
FL2
4B
L02R
N2
FL2
5B
L02R
N2
FL2
6B
L02R
N2
FL2
7B
L02R
N2
+ C11
47u/
50V
CP
111u
Vcc
25
ALM
3
PhA
5
PhB
23
EA
6
EB
22
Vre
fA2
Vre
fB26
CR
4
VsA
1
RsA
11R
sB17
PG
13
VsB
27
Vm
mA
8
Vm
mB
20
Out
A10
Out
A12
Out
B14
Out
B18
LG A
7
LG B
21
Dec
ay24
IC12
MT
D20
05
R3 10
kC
1439
00p
D2
D1FL20U
D3
D1FL20U
D4
D1FL20U
D5
D1FL20U
TX
DA
RX
DA
/RT
SA
RX
DB
/DT
RA
/DS
RA
TX
DB
R36
2.7K
R37
2.7K C17
2200
p
C18
2200p
PhGA
PhGB
Vre
fGA
Vre
fGB
Gm
A+
Gm
A-
Gm
B-
Gm
B+
1 2 3 4
CN
3
5267
-04A
Vm
m
Vcc
Vcc
FL2
8B
L02R
N2
FL2
9B
L02R
N2
+
C12
47u/
50V
CP
121u
Vcc
25
ALM
3
PhA
5
PhB
23
EA
6
EB
22
Vre
fA2
Vre
fB26
CR
4
VsA
1
RsA
11R
sB17
PG
13
VsB
27
Vm
mA
8
Vm
mB
20
Out
A10
Out
A12
Out
B14
Out
B18
LG A
7
LG B
21
Dec
ay24
IC14
MT
D20
05
R4
15k
C15
3900
p
D6 D
1FL2
0UD
7D
1FL2
0U
R52
8.2K
C19
0.01
u
Vre
fSO
L
R23 1k
R24
1k
R25
1K
R55
39K
R56
0.68
1W
R57
0.68
1W
R26
1K
R27
1KC
6
1000
p
C7
1000
p
R5 10
K
Vcc
CP
421u
R61
No
Mou
nt
/RD
/WR
Dra
m
/CA
SH
/CA
SL
/RA
S
/Ena
bleM
TD
Dec
ayM
OT
C20
0.01
u
81
72
63
54
RA
4
33x4
81
72
63
54
RA
5
33x4 8
17
26
35
4
RA
6
33x4
81
72
63
54
RA
7
33x4
A0
17
A1
18
A2
19
A3
20
A4
23
A5
24
A6
25
A7
26
A8
27
A9
28
D0
2
D1
3
D2
4
D3
5
D4
7
D5
8
D6
9
D7
10
D8
33
D9
34
D10
35
D11
36
D12
38
D13
39
D14
40
D15
41
Vcc6
Gnd 22
Gnd37
OE
29
WE
13
UC
AS
30
LCA
S31
RA
S14
Gnd42
Vcc1
Vcc21
IC15
16M
DR
AM
CP
131u
CP
141u
CP
151u
CP
161u
CP
17
1u
Vcc
CP
18
1u
A18
CP
19
1u
CP
20
1u
CP
21
1u
CP
22
1u
CP
23
1u
81
72
63
54
RA
8
22K
x4
Vcc
CP
241u
81
72
63
54
RA
9
22K
x4
A4A5A6
A1
B2
C3
G1
6
G2A
4
G2B
5
Y0
15
Y1
14
Y2
13
Y3
12
Y4
11
Y5
10
Y6
9
Y7
7
VCC16 GND 8IC1674
HC
138
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
CP
251u
CP
261u
Vm
m
Vcc
Vcc
FL3
0B
L02R
N2
FL3
1B
L02R
N2
FL3
2B
L02R
N2
FL3
3B
L02R
N2
+ C13
47u/
50V
CP
271u
Vcc
25
ALM
3
PhA
5
PhB
23
EA
6
EB
22
Vre
fA2
Vre
fB26
CR
4
VsA
1
RsA
11R
sB17
PG
13
VsB
27
Vm
mA
8
Vm
mB
20
Out
A10
Out
A12
Out
B14
Out
B18
LG A
7
LG B
21
Dec
ay24
IC13
MT
D20
05
R6
10k
C16
3900
p
D8
D1FL20U
D9
D1FL20U
D10
D1FL20U
D11
D1FL20U
R53
5.6KR
545.
6K
C21 22
00p
C22
2200
p
PhCA
PhCB
VrefCA
VrefCB
Cm
A+
Cm
A-
Cm
B-
Cm
B+
1 2 3 4
CN
4
5267
-04A
R28 1k
R29
1k
R58
0.68
1W
R59
0.68
1W
R30
1K
R31
1KC
8
1000
pC
910
00p
DQ
11
DQ
02
WR
3
RD
4
A0
5
S0
6
IBF
07
OB
F0
8
CNVss9
RE
SE
T10
Tou
t/XC
out
11
XC
in12
Vss13
Xin
14
Xou
t15
Vcc16
AVcc 17
LPF18AVss19
INT
122
INT
023
ED
MA
24
RT
S1
25
CT
S1
26
UR
XD
127
UT
XD
128
RD
B33
WR
B34
SY
NC
out
35
SY
SC
LKou
t36
DM
Aou
t37
P32
38
P31
39
RD
Y40
AB
1541
AB
1442
AB
1343
AB
1244
AB
1145
AB
1046
AB
947
AB
848
AB
749
AB
650
AB
551
AB
452
AB
353
AB
254
AB
155
AB
056
DB
757
DB
658
DB
559
DB
460
DB
361
DB
262
DB
163
DB
064
OB
F1
65IB
F1
66S
167
HO
LD68
SO
F69
USB D+ 70
USB D-71
XcvrPower/Ext.Cap72
Vss73
Vcc74
DQ
775
DQ
676
DQ
577
DQ
478
DQ
379
DQ
280
US
BC
CN
TR
120
CN
TR
021
RT
S2/
ST
XD
29
CT
S2/
SR
XD
30
UR
XD
2/S
CLK
31
UT
XD
2/S
RD
Y32
IC18
Non
A1
B2
C3
G1
6
G2A
4
G2B
5
Y0
15
Y1
14
Y2
13
Y3
12
Y4
11
Y5
10
Y6
9
Y7
7
VCC16 GND 8IC1774
HC
138
/CS
2
/CR
D
/LC
DE
n/K
eyR
D
/LC
DE
n
R60
0.68
1W
R32
1KC
10
1000
p
VoA 2VoB
1VoC20
VoD19
A017
A116
LDAC6
DB014 DB113
DB212DB3
11 DB410
DB59 DB68
DB77
Gnd5
WR15
Vref4
Vdd18
Vss 3
IC19
AD
7305
D14D2
5D312D4
13
CLK9 CLR1
Q12
Q2 7
Q3 10
Q415
Vcc16
Gnd8
Q13
Q26
Q311
Q4 14
IC20
74H
C17
5
D0D1D2D3D4D5D6D7
D0D1D2D3
/PhaseWR
/uStepWR
567
8 4
IC21
A
NJU
7032
3
21
IC21
BN
JU70
32
A1
A2
/Res
et
R63
47K
C23
0.01
u
DirS
OL
Dec
ayS
OL
8 17 26 35 4
RA11
10Kx4
Chk
Vfa
n
81
72
63
54
RA
10
22K
x4
/CR
D
A0
10A
19
A2
8A
37
A4
6A
55
A6
4A
73
A8
25A
924
A10
21A
1123
A12
2A
1326
A14
1D
011
D1
12
D2
13
D3
15
D4
16
D5
17
D6
18
D7
19
OE
22
W27
CE
20
Vcc28
Vss14
IC22
Non
VC
C1
-Dat
a2
+Dat
a3
Gro
und
4
Cas
e1A
5A
Cas
e2B
6B
Cas
e1B
5B
Cas
e2A
6A
CN
5N
onC
P28
Non
CP
29N
on
FL34 Non
FL35Non
R33
Non
R64
Non
R65
Non
R66
Non +
C30
Non
C31
Non
CP
30N
on
FL3
6N
onFL3
7N
on
C32
Non
C33
Non
C34
Non
C35
Non
FL38Non F
L39
Non
C36
Non
C37
Non
C38
Non
R17
Non
X2
Non
1 2 3 4 5678910
RA
13N
on
1 2 3 4 5678910
RA
14
Non
1 2 3 4 5678910
RA
15
Non
R7
Non
R8
Non
D0
D1
D2
D3
D4
D5
D6
D7
/RD
/WR
A1
A1
/RD
/WR
/Res
et
R9
10K
R10
Non
R11
10KR
12N
on
123456789
10111213141516171819202122232425
CN
6IL
-FP
C-2
5ST
-N
CR
Sen
s
C39
2200
p
Vcc
CP
311u
FL13FL14
FL15
FL16FL17
FL18FL19
FL20FL21
FL22
Vcc C
P32
1u
FL23
8 17 26 35 4
RA12
10Kx4
/Key
RD
A2
A1
ELC
D
D0D1D2D3D4D5D6D7
C24
0.01
u
C250.
01u
Pap
Sen
sFP
apS
ensR
Vcc
123456
CN
753
014-
0610
+C
4010
u/50
V
L1R
CH
895-
181K
D12
D1F
L20U
Q1
2SK
2796
S
Vm
m
R51 10
0
R34
1K
Vcc
Fan
PW
M
Q2
DT
A11
4E
D13
D1F
L20U
C26
0.01
u
CP
331u
R13
10K
R67
33K
R45
3.3K
C27
0.01
u
12
CN
852
67-0
2A
CP
34
1u
Chk
Vm
m
JogA
JogB
E2C
SE
2CLK
E2D
inE
2Dou
t
1 2 3 4
CN
9
B4P
-VH
+C
4110
0u/1
6v
Vm
m
Vcc
Vcc14
Gnd7
IC6G
74LS
14V
cc
CP
35
1u
Vcc C
P36
1u
Vcc
CP
371u
Vcc
CP
381u
Vcc14
Gnd7
IC3E
74LV
08A
CP
39
1u
CP
40 1u
TP
1T
P2
TP
3
TP
4
1 24 3
S1
SW
DIP
-2
Vcc
Mon
itor
Mod
el
Vfan
TP
5T
P6
/WR
SOL+
SOL-
CP
41 1u
R71
33K
R70
3.3K
C42
0.01
u
R72
1.2
1W
FanVmm
R16
22K
R62
22KV
cc
R691.2K
R73
1.2k
R74
1.2k
R75
1.2k
C44 0.
068u
C45
0.06
8u
C46
0.06
8u
C47
0.06
8u
R76
10K
R77 10
K
R78 22
K
R79
22K
A2
24
5 3
IC23
TC
7S04
F
C48 1u
FL12EXC3BB601H
A1
B2
G3
Y0
7
Y1
6
Y2
5
Vcc8
Gnd4
IC24
Non
A4
A5
/CS
2
A4
A5
Vcc
/CS
2/C
S3
1311
12IC
3D
74LV
08A
C28
2200
p
C29
2200
p
/LC
DE
n
R82
100K
R83
100K
Sel
Sen
sor
FL40EXC3BB601H
R14
1.2k
2 Electrical Section
2-4
2
2-3 OTHER CIRCUIT BOARDS OTHER CIRCUIT BOARDS_1/2 Circuit Diagram
1 2 3 4 5678910
RA
16
10K
x8
R44
Non
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
CN
10
IL-F
PC
-25S
T-N
CP
431u
CP
441u
SW
1S
W K
EY
SW
2S
W K
EY
SW
3S
W K
EY
SW
4S
W K
EY
SW
5
SW
KE
Y
SW
6S
W K
EY
SW
7S
W K
EY
SW
8S
W K
EY
A B C
EN
1JO
G E
NC
OD
ER
1 2 3 4 5 6 7 8 9 10 11 12 13 14CN
12
14F
PZ
-SM
-TF
PN
-VC
C
PN
-VC
C
PN
-VC
C
PN
-VC
C
PN
-GN
D
PN
-GN
D
PN
-GN
D
PN
-GN
D
PN
-GN
D
PN
-GN
DP
N-G
ND
PN
-GN
DP
N-G
ND
PN
-GN
DP
N-G
ND
PN
-GN
DP
N-G
ND
R68
0
CP
45
1u
OR
IGIN
EN
TE
R
ME
NU
TE
ST
A1
2
A2
3
A3
4
A4
5
A5
6
A6
7
A7
8
A8
9
G19
DIR
1
B1
18
B2
17
B3
16
B4
15
B5
14
B6
13
B7
12
B8
11
Vcc20 GND 10IC
2574
LS24
5P
N-/
Key
RD
PN
-Jog
AP
N-J
ogB
PN
-A2
PN
-A1
PN
-ELC
D
PN
-CR
Sen
sP
N-S
OL-
PN
-SO
L+
Orig
inE
nter
Rig
htU
pD
own
Left
Men
uT
est
VC
ont
PN
-D0
PN
-D1
PN
-D2
PN
-D3
PN
-D4
PN
-D5
PN
-D6
PN
-D7
98
IC27
D
74H
C04
56
IC27
C
74H
C04
1110
IC27
E
74H
C04
34
IC27
B
74H
C04
12
IC27
A
74H
C04
1312
IC27
F
74H
C04
Vcc14
Gnd 7
IC27
G74
HC
04
R84
33 R85
33
R86
33 R87
33
PN
-Opt
-AP
N-O
pt-B
R19
47K
C43
2200
p
C49
2200
p
PN
-GN
D
12345678
CN
11IL
-FP
C-8
ST
PANEL BOARD
2 Electrical Section
2-5
2
12
CN14
IL-S2P-S2L
c-Sol+c-Sol-
R80
220
R81
220
c-Sens
c-Opt-A
c-Opt-B
12345
CN15
53014-0510
1234
CN16
53014-0410
R90Non
R91Non
R880
R890
C-GND
12345678
CN13
IL-FPC-8SL
CARRIAGE BOARD
12
34
IC26GP1L57
sp-LedAN
sp-TrE
sp-TrC
SP1
SP3
SP2
SP4
sp-LedKA
sm-LedAN
sm-TrE
sm-TrC
SM1
SM3
SM2
SM4
sm-LedKA
41
32
IC28NJL5265KL
S-GndM-Gnd
Mark Sensor Pinch Sensor
OTHER CIRCUIT BOARDS_2/2 Circuit Diagram
SENSOR BOARD
3 Replacement of Main Parts
3-1
3
3 Replacement of Main Parts
Following table describes the necessary adjustment after the replacement of each parts.
3-1 TOOL CARRIAGE_REPLACEMENT (Referential Time : 10 min.)
1
Remove the FRONT COVER by disconnecting the flatcables from the Panel Board.
Remove the FRONT COVER.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
(RIGHT SIDE)
(FRONT VIEW)
(CX-24 Only)
Revised 4
Replacement Parts Necessary AdjustmentMain Board 1. Upgrade Firmware
2. Initialize3. Tool Pressure Adjustment4. Calibration5. Crop Mark Sensor Adjustment
Replacement Parts Necessary AdjustmentTool Carriage 1. Tool Height Adjustment
2. Tool Pressure Adjustment3. Crop Mark Sensor Adjustment
Replacement Parts Necessary AdjustmentDrive Gear 1. Motor Backlash Adjustment
Replacement Parts Necessary AdjustmentMotor 1. Motor Backlash Adjustment
Revised 4
Revised 4
CROP MARK SENSOR has been fixed to themachines with the following serial number.CX-24 : ZQ81680 and aboveCX-12 : ZQ81680 and above
3 Replacement of Main Parts
3-2
3
2 Remove the Y RAIL COVER.
(BINDING HEAD WITH TEETH WASHER M3X8 Ni /4pcs.)
3 Disconnect the 3 cables.
(REAR VIEW)
(CARRIAGE JUNCTION BOARD)
4
5
Unhook and remove the screws for fixing the TOOLCARRIAGE.
(W SEMS M3X6 Ni / 2pcs.)
Remove the CARRIAGE COVER and the TOOLCARRIAGE.
(CARRIAGE COVER : W SEMS M3X6 Ni / 1pce.)(TOOL CARRIAGE : W SEMS M3X8 Ni / 2pcs.)
(TOOL CARRIAGE)
SCREWS
HOOK (WHITE)
SCREWS
3 Replacement of Main Parts
3-3
3
6
7
8
9
Remove the INSULOCK TIE for fixing the cables.
Fix the CROP MARK SENSOR CABLE and TOOLCARRIAGE CABLE with the INSULOCK TIE.
Fix the (New) CROP MARK SENSOR to the NewTOOL CARRIAGE.
(BINDING M2.6X4 C / 2pcs.)
Remove the screws for fixing the CROP MARKSENSOR.
(BINDING M2.6X4 C / 2pcs.)
SCREWS
SCREWS
INSULOCK TIE
INSULOCK TIE
(CARRIAGE_BOTTOM)
(CARRIAGE_BOTTOM)
C R O P M A R KSENSOR CABLE
TOOL CARRIAGECABLE
3 Replacement of Main Parts
3-4
3
10
11
(TOOL CARRIAGE)
12
13
SCREWS
SCREWS
(REAR VIEW)
HOOK(White)
Pass the Sensor Cable through the hole of the TOOLCARRIAGE and fix the TOOL CARRIAGE by pushingit upwards.Then, fix the CARRIAGE COVER.
(TOOL CARRIAGE : W SEMS M3X8 Ni / 2pcs.)(CARRIAGE COVER : W SEMS M3X6 Ni / 1pce.)
(CARRIAGE JUNCTION BOARD)
Fix the Y RAIL COVER.
(BINDING HEAD with TEETH WASHER M3X8 Ni /4pcs.)
Connect the 3 cables.
Fix the screws for fixing the TOOL CARRIAGE.And then, fix the cables with the hook.
(W SEMS M3X6 Ni / 2pcs.)
SENSORCABLE
3 Replacement of Main Parts
3-5
3
Carry out the following adjustments.
1. Tool Height Adjustment2. Tool Pressure Adjustment3. Crop Mark Sensor Adjustment
14
(FRONT VIEW)
(CX-24 Only)
15
(RIGHT SIDE)
Connect the flat cables to the Panel Board.
Make sure that the blue line on the big cable facesupwards and the blue line on the small cable facesleft when connecting them.
Fix the FRONT COVER.CX-24 : Fix the screws at the center first and them
both sides.CX-12 : Fix the screws from the left side.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
3 Replacement of Main Parts
3-6
3
3-2 MAIN BOARD_REPLACEMENT (Referential Time : 10min.)
2
3 Remove the GUIDE COVER R.
(BINDING HEAD with TEETH WASHER M3X8 Ni /4pcs.)
Remove the FRONT COVER by disconnecting the 2flat cables from the Panel Board.
Remove the FRONT COVER.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
Remove the Y RAIL COVER.
(BINDING HEAD WITH TEETH WASHER M3X8 Ni /4pcs.)
(FRONT VIEW)
(CX-24 Only)
(RIGHT SIDE)
(REAR VIEW)
(REAR VIEW)
3 Replacement of Main Parts
3-7
3
4
6
Remove the screws of the Parallel Cable and nuts ofthe Serial Cable.
Disconnect all the cables (5 pcs.) from the MAINBOARD.
7
5
Remove the screws from the MAIN BOARD and theHeat Sink. And disconnect the Cable on the MAINBOARD.
(W SEMS M3X6 Ni / 6pcs.)
Remove the RIGHT SIDE COVER.
(BINDING HEAD M4X5 Ni / 4pcs.)
(RIGHT SIDE)
HOOK (White)
PARALLELSERIAL
MAIN BOARD
CABLE
3 Replacement of Main Parts
3-8
3
Connect the cables (5pcs.) to the MAIN BOARD.
Make sure connect the wirings to the right place.Carriage Motor Cable CN4Grit Motor Cable CN3Fan Cable (Red and Black) CN8Paper Sensor Cable (Yellow and Blue) CN7Switching Power Cable CN9
Remove the MAIN BOARD.8
10
Fix the new MAIN BOARD and connect the CABLE onthe MAIN BOARD.
(W SEMS M3X6 Ni / 6pcs.)
9
Fix the screws of the Parallel Cable and nuts of theSerial Cable.
PARALLELSERIAL
MAIN BOARDCABLE
3 Replacement of Main Parts
3-9
3
12
13
14
15
(RIGHT SIDE)
(REAR VIEW)
Fix the RIGHT SIDE COVER.
(BINDING HEAD M4X5 Ni / 4pcs.)
Fix the Y RAIL COVER.
(BINDING HEAD with TEETH WASHER M3X8 Ni /4pcs.)
(REAR VIEW)
Fix the cables with the hook and put the hook to theRight Side Frame. HOOK (White)
Fix the GUIDE COVER R.
(BINDING HEAD with TEETH WASHER M3X8 Ni /4pcs.)
3 Replacement of Main Parts
3-10
3
Carry out the following adjustments.
1. Upgrade Firmware2. Initialize3. Tool Pressure Adjustment4. Calibration5. Crop Mark Sensor Adjustment
17
16
(FRONT VIEW)
(CX-24 Only)
(RIGHT SIDE COVER)
Connect the flat cables to the Panel Board.
Make sure that the blue line on the big cable facesupwards and the blue line on the small cable facesleft when connecting them.
Fix the FRONT COVER.CX-24 : Fix the screws at the center first and them
both sides.CX-12 : Fix the screws from the left side.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
Revised 4
3 Replacement of Main Parts
3-11
3
3-3 CARRIAGE MOTOR_REPLACEMENT (Referential Time : 5 min.)
1
2
3 Disconnect the CARRIAGE MOTOR WIRE from CN4of the MAIN BOARD.
(RIGHT FRONT)CN4
Remove the FRONT COVER.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
(CX-24 Only)
(FRONT VIEW)
Remove the FRONT COVER by disconnecting the flatcables from the Panel Board.
(RIGHT SIDE COVER)
Remove the RIGHT SIDE COVER.
(BINDING HEAD M4X5 Ni / 4pcs.)
(RIGHT SIDE )
3 Replacement of Main Parts
3-12
3
4
Fix the new CARRIAGE MOTOR together with theSPACER to the FRAME so that there won't be anylooseness or to much load.
(W SEMS PRECOATING LOCK AGENT M3X8 C /2pcs.)
5
Connect the CARRIAGE MOTOR WIRE to the CN4on the MAIN BOARD.
6
7
Remove the CARRIAGE MOTOR.
(W SEMS PRECOATING LOCK AGENT M3X8 C /2pcs.)
The position of the screws fixing the CX-24CARRIAGE MOTOR is different from CX-12.
SCREWS
CN4
The position of the screws fixing the CX-24SPACER is different from CX-12.
(RIGHT SIDE )
(RIGHT FRONT)
(RIGHT REAR)
SCREWS(CX-24) (RIGHT REAR)
SPACER
Fix the RIGHT SIDE COVER.
(BINDING HEAD M4X5 Ni / 4pcs.)
SCREWS(CX-12)
3 Replacement of Main Parts
3-13
3
8
(RIGHT SIDE)
(FRONT VIEW)
(CX-24 Only)
Connect the flat cables to the Panel Board.
Make sure that the blue line on the big cable facesupwards and the blue line on the small cable facesleft when connecting them.
Fix the FRONT COVER.CX-24 : Fix the screws at the center first and them
both sides.CX-12 : Fix the screws from the left side.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
3 Replacement of Main Parts
3-14
3
3-4 GRIT MOTOR_REPLACEMENT (Referential Time : 5 min.)
1
Remove the Y RAIL COVER.
(BINDING HEAD WITH TEETH WASHER M3X8 Ni /4pcs.)
Remove the FRONT COVER by disconnecting the flatcables from the Panel Board.
Remove the LEFT SIDE COVER.
(BINDING HEAD M4X5 Ni / 4pcs.)
Remove the FRONT COVER.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
(FRONT VIEW)
(CX-24 Only)
(RIGHT SIDE COVER)
(LEFT SIDE )
(REAR VIEW)
3 Replacement of Main Parts
3-15
3Remove the GRIT MOTOR WIRE from the CN3 onthe MAIN BOARD.
CN3
Remove the GRIT MOTOR.
(W SEMS PRECOATING LOCK AGENT M3X8 C /2pcs.)
(LEFT SIDE)
GRIT MOTOR
SCREWS
6
Fix the GRIT MOTOR so that there won't be anylooseness or too much load.
(W SEMS PRECOATING LOCK AGENT M3X8 C /2pcs.)
7
Remove the COVER GUIDE R.
(BINDING HEAD WITH TEETH WASHER M3X8 Ni /4pcs.)
(REAR VIEW)
(RIGHT FRONT)
GRIT MOTOR
(LEFT SIDE)SCREWS
The GRIT MOTOR CABLE should be thefront side when fixing the ASS'Y MOTOR Y.
GRIT MOTORCABLE
3 Replacement of Main Parts
3-16
3
Connect the GRIT MOTOR WIRE to the CN3 on theMAIN BOARD.
CN3
Fix the Y RAIL COVER.
(BINDING HEAD with TEETH WASHER M3X8 Ni /4pcs.)
(RIGHT FRONT)
Fix the COVER GUIDE R.
(BINDING HEAD WITH TEETH WASHER M3X8 Ni /4pcs.)
(REAR VIEW)
(REAR VIEW)
Fix the LEFT SIDE COVER.
(BINDING HEAD M4X5 Ni / 4pcs.)
(LEFT SIDE )
3 Replacement of Main Parts
3-17
3
Connect the flat cables to the Panel Board.
(RIGHT SIDE)
(FRONT VIEW)
(CX-24 Only)
Make sure that the blue line on the big cable facesupwards and the blue line on the small cable facesleft when connecting them.
Fix the FRONT COVER.CX-24 : Fix the screws at the center first and them
both sides.CX-12 : Fix the screws from the left side.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
3 Replacement of Main Parts
3-18
3
3-5 PINCH ROLLER_REPLACEMENT (Referential Time : 5min.)
1 Lower the SHEET LOADING LEVER to raise thePINCH ROLLER.
Remove the SHAFT.
Remove one of the E-RING with the Flat Head driver.
Fix the new PINCH ROLLER with washers by passingthe SHAFT through the PINCH ROLLER.
E-RING
Set the Sheet to prevent the washer from droppingduring the replacement.
Be careful with the direction of the PINCH ROLLER. The marked side should be outside.
SHAFT
3 Replacement of Main Parts
3-19
3
Fix the E-RING with pincers.
Put the CUTTER PROTECTION fully from the left edgeof the APRON and along the MARK on theFRAME,CENTER.There would be space at the right edge.
3-6 CUTTER PROTECTION_REPLACEMENT (Referential Time : 5 min.)
(FRONT VIEW)
E-RING
0 ~ 1mm
CUTTER PROTECTION
MARKThe machines with the following serialnumber have been carved the MARK.CX-24 : ZN92130 and aboveCX-12 : ZO 00370 and above
Revised 1
4-1
4 Adjustment
4
Tool No. ST-002
Tool Name TENSION GAUGE 3N (300gf)
Purpose Tool Pressure Adjustment
Tool No. ST-006
Tool Name WHITE DUMMY PEN
Purpose Tool Height Adjustment
Tool Pressure Adjustment
Tool No. ST-012
Tool Name DIAL TENSION METER DT-50 0.5N (50gf)
Purpose Tool Pressure Adjustment
4 Adjustment4-1 Special Tool
Table shows a list of special tools recommended by Roland DG Corp.
4-2
4 Adjustment
4
4-2 Service Mode
[ ], [ ], [ ] + POWER ON
VERSION A100 Display the version of Firmware.
[Clockwise]
Turn the dial to selectthe menu.
[Counterclockwise]
KEY START This menu is for checking the Panel Keys. It will be checked [MENU/PARAM], [ENTER], [TEST], [ORIGIN] ,[ ], [ ], [ ], [ ] in order.
SENSOR F1 R1 C1
FAN OFF This menu is for checking the FAN.ON/OFF will be changed by pressing the [ENTER] key.
KEY
This menu is for checking the ON / OFF status of Sensor.F : Front Pepare Sensor R : Rear Paper SensorC : Carriage Sensor
1 : ON 0 : OFF
SENSOR F1 R1 C1
FAN OFF[MENU/PARAM]
[MENU/PARAM]
[MENU/PARAM] ********
F-35g U < 33> This menu is for adjusting the MIN Tool Pressure. Refer to section 4 [TOOL PRESSURE ADJUSTMENT] for details.
F-200g U <155>
F-35g U < 33>
F-200g U <155>
[MENU/PARAM]
[MENU/PARAM]
CALIB-G < 0.11>
Select the Calibration Checking DATA by turning the dial and press the [ENTER] key to draw a figure.
This menu is for Calibration of the Grit Roller side. The value is %.CALIB-G < 0.11>
DATA1 DATA2
[TEST]
[MENU/PARAM]
[MENU/PARAM]
CALIB-C < 0.11> This menu is for Calibration of the Carriage Moving. The value is %.CALIB-C < 0.11>
DATA1 DATA2
[MENU/PARAM]
[MENU/PARAM]
[TEST]
Service Mode
Go toNext Page.
[Counterclockwise]
[Clockwise]
[Clockwise]
[Clockwise]
[Clockwise]
[Clockwise]
[Clockwise]
[Clockwise]
[Counterclockwise]
[Counterclockwise]
[Counterclockwise]
[Counterclockwise]
[Counterclockwise]
[Counterclockwise]
This menu is for adjusting the MAX Tool Pressure. Refer to section 4 [TOOL PRESSURE ADJUSTMENT] for details.
Select the Calibration Checking DATA by turning the dial and press the [ENTER] key to draw a figure.
CROP START [MENU/PARAM] CROP START
[Clockwise]
This menu is for Crop Mark Sensor Auto Calibration.
Revised 4
4-3
4 Adjustment
4
AGING STARTThis menu is for AGING.AGING starts after pressing the [MENU/PARAM] key and it will be stop after turning the power off.
PENWAIT < 0>This menu is for setting the time from going the Pen or the Cutter down until moving. The range of the time is 0 ~ 99 (msec).Ending menu of the Service Mode.
AGING START
PENWAIT < 0>
[MENU/PARAM]
[MENU/PARAM]
EEROM START
DRAM START
This menu is for checking the EEROM.Either [OK] or [NG] will be indicated after the check
EEROM check OK!
DRAM check OK!
[MENU/PARAM]
[MENU/PARAM]
[ ], [ ], [MENU/PARAM] + POWER ON
KEY Dir <Forw.>
EXIT
COMMAND <AUTO>
This menu is for setting the COMMAND.AUTO : AUTO (Default)MODE2 : COMMAND CAMM-GL3 MODE 2 FixedMODE1 : COMMAND CAMM-GL3 MODE 1 Fixed
MARK <OFF> Always OFF.
[MENU/PARAM]
[MENU/PARAM]
[MENU/PARAM] KEY Dir <Forw.>
MARK <OFF>
COMMAND <AUTO>
This menu is for setting the media feeding direction when pressing the [ ], [ ].Forw : The media feeds forward with [ ] key. (Default)Rev : The media feeds backward with [ ] key.
Movement Mode
[Clockwise]
Fromlast Page.
[Counterclockwise]
[Counterclockwise]
[Clockwise]
[Counterclockwise]
[Clockwise]
[Counterclockwise]
[Clockwise]
This menu is for checking the DRAM.Either [OK] or [NG] will be indicated after the check
[Counterclockwise]
[Clockwise]
Turn the dial to selectthe menu.
Turn the dial to selectthe menu.
[Counterclockwise]
[Clockwise]
[Counterclockwise]
[Clockwise]
[Clockwise]
Press the [ENTER] key to reset and go back to the general menu.
!FScmd <ON>This menu is for setting the Tool Pressure Control Command (!FS).ON : EnableOFF : Disable (Default)
[MENU/PARAM] !FScmd <OFF>
Turn the dial to selectthe menu.
Turn the dial to selectthe menu.
[Counterclockwise]
CROP G < -31>
CROP C < 416>
CROP AD 468
[MENU/PARAM]
[MENU/PARAM]
[MENU/PARAM]
CROP G < -31>
CROP C < 416>
CROP AD 468
[Clockwise]
[Clockwise]
[Clockwise]
[Counterclockwise]
[Counterclockwise]
[Counterclockwise]
This menu is for checking the movement of the Crop Mark Sensor.This value will change depending on the media.
This menu is used when Auto Calibration cannot be done. This menu shows the distance in Grid direction between the center of the Sensor and the center of the cutter.This value will change by Jog Dial. (1 step = 0.05mm)
This menu is used when Auto Calibration cannot be done. This menu shows the distance in Carriage direction between the center of the Sensor and the center of the cutter.This value will change by Jog Dial. (1 step = 0.05mm)
Revised 2
4-4
4 Adjustment
4
4-3 Function Mode
SERIAL INTERFACE CHECK
SYSTEM REPORT
Turn on the power while pressing the [ ] key.
SYSTEM REPORTMODEL : CX-24MAIN : A100BOOT : B100
--- PARAM ---CALIB. : C=0.00% G = 0.00%FORCE DA : MAX= 170 MIN= 45CROP ENABLE: OFFCROP OFFSET: X= 430 Y= -29 LANGUAGE : ENGLISH
--- SAVE MENU --- No \ ITEM FORCE[g] SPEED[cm/s] OFFSET WEIGHTCURRENT : 100 40 0.250 LIGHTSAVE1 : 50 40 0.250 LIGHTSAVE2 : 50 40 0.250 LIGHTSAVE3 : 50 40 0.250 LIGHTSAVE4 : 50 40 0.250 LIGHTSAVE5 : 50 40 0.250 LIGHTSAVE5 : 50 40 0.250 LIGHTSAVE6 : 50 40 0.250 LIGHTSAVE7 : 50 40 0.250 LIGHTSAVE8 : 50 40 0.250 LIGHT
--- OTHER PARAMETER ---AREA : 1.0 [m] , ROTATE: OFFSAVE : USER1 , PRESET: USER1 SMOOT : ON , I/O : AUTOBAUD : 9600 , DATA : 8STOP : 1 , PARITY : NONEHAND : H-WIRE , U-CROP : OFF
UNIT : Metric , CURSOR: Forw. COMMAND: AUTO , PENWAIT: 0[msec]!FScmd : OFF-- END ---
Displayed Language and Unit
LINGUA <ITAL.>
[MENU/PARAM]
[ENTER]
[ENTER]
[MENU/PARAM]
Languages : English, Japanese, German, French, Spanish, Italian and Portuguese
Unit : Metric (mm), Inch
LINGUA <ITAL.>
LINGUA ENGLIS
LANG. <ENGLIS>
[ENTER]
INITIALIZE EEROM
[ENTER]
ENTER ->START INT
COMPLETED
LIMITED INITIALIZE
All data inside the EEPROM will be initialized.
ALL INITIALIZE
Init ALL EEROM
[ENTER]
ENTER ->ALL INIT
FINISH
RTS-DSR errorDTR-CTS errorTxD-RxD errorSTxD-SRxD error
Connection2 (TxD) 3 (RxD)4 (RTS) 6 (DSR)5 (CTS) 20 (DTR)14 (STxD) 16 (SRxD)
Error bit = 1111
RS232C check
EXIT
UNIT <Metric>
Turn on the power while pressing the [MENU/PARAM] key.
UNIT <Metric>
UNIT Inch
UNIT <Inch>
Turn on the power while pressing the [ ], [ ], [ORIGIN] keys.
Turn on the power while pressing the [ ] key.
Turn on the power while pressing the [ENTER] key.
The data which the customer sets inside the EEPROM
will be initialized.
Revised 2
4-5
4 Adjustment
4
4-4 HOW TO UPGRADE FIRMWARE (Referential Time : 5 min.)
1 Connect PC and CX-24/12 with the PARALLELCABLE.
2 Turn on the power while pressing [ ], [ ], [ ]keys.It is ready to receive data when [Send new program]is displayed.
3 Open the download.BAT from MS-DOS.
4 Turn off the power when the upgrade is completed.
It is necessary to prepare the followings toupgrade the FIRMWARE.
1. FIRMWARE DISK2. PC with MS-DOS3. PARALLEL CABLE
Some PCs can not use the BAT FILE.Please refer to the ReadMe File in theFIRMWARE DISK.
COMPLETE
POWER OFF
[ENTER]
[ ] [ ] [ ] + POWER ON
VERSION UP SURE?
Send new program
CX-XX V.A 100 %
ERASE %
WRITE %**
**
**
4-6
4 Adjustment
4
4-5 TOOL HEIGHT ADJUSTMENT (Referential Time : 20min.)
1
2
TOOL HEIGHT ADJUSTMENT is designed to cut the whole media equally and ensure cuttingquality by eliminating tool-bouncing as the tool traverses the media.This adjustment must be performed after replacement of the TOOL CARRIAGE.Roland Special Tool ST-006, Thickness Gauge and 1mm Hexagonal wrench are used for thisadjustment.
Remove the Carriage Cover.
(W SEMS M3X6 Ni / 1pce.)
Make sure not to disconnect the flat cables from thePanel Board.
Screw
Remove the screws fixing the FRONT COVER.
(CX-24 : W SEMS M3X8 BC / 6pcs.)(CX-12 : W SEMS M3X8 BC / 4pcs.)
(FRONT VIEW)
(CX-24 Only)
(RIGHT SIDE COVER)
4-7
4 Adjustment
4
Put the WHITE DUMMY PEN (ST-006) to the TOOLCARRIAGE. Make sure to insert until the collar of theblade holder touches the rim of the hole.
5
3
CX-24 : Make sure to cover the FRONT /REAR PAPER SENSOR with paper and turnon the power.
4 Put the PINCH ROLLER down at the both ends ofGRIT ROLLER
Turn on the power and press the [ENTER] key.
6
Remove the Y RAIL COVER.
(BINDING HEAD WITH TEETH WASHER M3X8 Ni /4pcs.)
(REAR VIEW)
4-8
4 Adjustment
4 8 Adjusting Screw
7 Move the TOOL CARRIAGE to the positions shown inthe right figure with the [ ], [ ] keys.Carry out Adjustment 8 at the position where theclearance between the pen tip and the BED is thelowest.
Adjust the Adjusting Screw so that the clearancebetween the pen tip and the BED will be more than2.4 / less than 2.6 with 1mm Hexagonal wrench.
Thickness Gauge
Make sure to adjust the Adjusting Screw sothat the 2.4mm thickness gauge can insertbetween the pen tip and the BED and 2.6mmthickness gauge can not insert.
4-9
4 Adjustment
4
1 Make sure to carry out TOOL HEIGHT ADJUSTMENTbefore this adjustment.
4-6 TOOL PRESSURE ADJUSTMENT (Referential Time : 15 min.)
Driver IC [MTD2005] supplies voltage,corresponds to the pen pressure, to thesolenoid of the Carriage. Tool Pressure couldbe set by adjusting the OFFSET with "MIN"adjustment and GAIN with "MAX" adjustmentof the TOOL PRESSURE ADJUSTMENT.
2
TOOL PRESSURE ADJUSTMENT is for adjusting the voltage supplied to the solenoid of theTOOL CARRIAGE to ensure that correct pressure would be added to the blade when cutting.This adjustment must be performed after replacement of the TOOL CARRIAGE.It is necessary to enter PEN PRESSURE MODE to perform this adjustment.Roland Special Tool ST-002, ST-006 and ST-012 are used for this adjustment.
Move the TOOL CARRIAGE to the position where theTOOL HEIGHT ADJUSTMENT has been carried out.
[Actual Pen Pressure]
[Pressure set from Panel]
200 g
20 g
20 g 200 g
Offset
Gain
Correct
Offset is not adjusted.
Gain is not adjusted.
4-10
4 Adjustment
4
3
4
5
Move the PEN down by pressing the [ ] key.Make sure to touch the pen tip to the BED.
Turn on the power while pressing [ ], [ ], [ ]keys to enter the Service Mode.Select [F-35g] menu and press [MENU/PARAM] keyto enter the Adjusting Mode.
0.3N ~ 0.4N(30gf ~ 40gf)
[MENU/PARAM]
VERSION A100
F-35g U < 33>
F-35g U < 33>
[ ] [ ] [ ] + POWER ON
Pull up the TOOL CARRIAGE with the DIAL GAUGE(ST-012) and measure the tool pressure when pen tipleaves the BED.
F-35g D <36>
[ENTER]
F-35g D < 33>
F-36g U <36>
Adjust the parameter in the menu with the dial so thatthe pressure will be 0.3N ~ 0.4N (30gf ~ 40gf).Press the [ENTER] key to save the settings.
Make sure to check the pressure with the DIALGAUGE (ST-012) again.
6
4-11
4 Adjustment
4
7
8
10
9
Select the [F-200g] menu and press the [MENU/PARAM] key to enter the adjusting mode.
F-200g U <155>
[MENU/PARAM]
F-35g U < 36>
F-200g U <155>
1.9N ~ 2.0N(195gf ~ 205gf)
[ ]
F-200g D <155>
F-200g D 157
F-200g U 157
Move the PEN down by pressing the [ ] key.Make sure to touch the pen tip to the BED.
Pull up the TOOL CARRIAGE with the TENSIONGAUGE (ST-002) and measure the tool pressurewhen pen tip leaves the BED.
Adjust the parameter in the menu with the dial so thatthe pressure will be 1.9N ~ 2.0N (195gf ~ 205gf).Press the [ENTER] key to save the settings.
Make sure to check the pressure with the TENSIONGAUGE (ST-002) again.
4-12
4 Adjustment
4
Turn on the power while pressing [ ], [ ], [ ]keys to enter the Service Mode.Select [CALIB -*] menu and press the [TEST] key.Then, select the [DATA2] with the dial.
4-7 CALIBRATION (Referential Time : 20 min.)
1 Put the 0.25mm Standard Ceramic Pen to the TOOLCARRIAGE.
2
3
Set A1 size paper on CX-24 and A3 size paper onCX-12.Make sure to set the edge of the paper to the Guideline.
[TEST]
VERSION A100
DATA1 DATA2
CALIB-G < 0.11>
[ ] [ ] [ ] + POWER ON
[CALIB - *] menu is used either [CALIB-G] or[CALIB -C].
CALIBRATION is designed to ensure the distance accuracy by adjusting the media-feedingrate. This adjustment must be performed after the MAIN BOARD or in case you like to improvethe distance accuracy.It is necessary to enter the CALIBRATION MODE to perform this adjustment.
4-13
4 Adjustment
4
Measure the length of CARRIAGE DIRECTION /GRIT ROLLER DIRECTION by using the figure.
If the measured length is within the following range, itdoes not need to calibrate.
[CX-24]Grit Direction : 748.5mm ~ 751.5mmCarriage Direction : 548.9mm ~ 551.1mm[CX-12]Grit Direction : 349.3mm ~ 350.7mmCarriage Direction : 249.5mm ~ 250.5mm
If the measured length is beyond the range, carry outthe 7 ~ 12 .
7
6
CX-24/12 will start drawing a figure when pressingthe [ENTER] key.
4
550mm
100mm
50mm
750mm
100mm
50mm
CX-24 AI SIZE
250mm
100mm50mm
350mm
100mm
50mm
CX-12 A3 SIZE
CARRIAGECARRIAGE
GRIT
GRIT
Lower the sheet loading lever and remove the sheet.
750 (350) mm - Measured Length (mm)
Measured Length (mm)X 100 = Calibrating
Amount (%)
[FOR EXAMPLE]
Calculate the amount to be calibrate by using the rightformula.
5
( FORMULA for the Grit Direction )
750mm - 752mm
752mmX 100 = - 0.3 (%)
4-14
4 Adjustment
4
Press the [MENU/PARAM] key to enter the menu andchange the Calibrating Amount with the dial.
Select the directions, GRIT ROLLER DIRECTION orCARRIAGE DIRECTION.
9
10
(Carriage Direction)
(Grit Direction)
8
CALIB-G < 0.11>
CALIB-C < 0.13>
[MENU/PARAM]
CALIB-G < 0.13>
CALIB-G -0.3
Press the [ENTER] key to save the settings.
If the both directions are needed to calibrate, pressthe [MENU/PARAM].Select another direction and carry out the 9 .
Enter the Calibrating Amount which is the amountcalculated at 7 .Calibrating range is -0.60% ~ +0.60%.
[MENU/PARAM]
CALIB-G < -0.3>
CALIB-G -0.3[ENTER]
CALIB-C < 0.13>
550 (250) mm - Measured Length (mm)
Measured Length (mm)X 100 = Calibrating
Amount (%)
[FOR EXAMPLE]
( FORMULA for the Carriage Direction )
550mm - 547mm
547mmX 100 = 0.5 (%)
4-15
4 Adjustment
4Measure the length of CARRIAGE DIRECTION orGRIT ROLLER DIRECTION by using the figure.
Make sure that the measured length is within thefollowing range.
[CX-24]Grit Direction : 748.5mm ~ 751.5mmCarriage Direction : 548.9mm ~ 551.1mm[CX-12]Grit Direction : 349.3mm ~ 350.7mmCarriage Direction : 249.5mm ~ 250.5mm
If the measured length is beyond the range, carry outthe 7 ~ 12 again.
11 Set the paper again and press the [TEST] key.Then, select the [DATA2] with the dial and CX-24/12will start drawing a figure when pressing the [ENTER]key. [TEST]
CALIB-G < -0.3>
DATA1 DATA2
DATA1 DATA2
[ENTER]
12
4-16
4 Adjustment
4
4-8 CROP MARK SENSOR CHECK (Referential Time : 20 min.)
This is for checking the sensitivity of the CROP MARK SENSOR with using the internaldata of the machine. It can be done without the influence of Application / Driver.
1
2
3
[MENU/PARAM]
SELECT I ROLL
SELECT I ROLL
1.5cm
2cm
5.7cmA4 size
Crop Mark(Diameter : 1cm) Printing Area
Prepare the followings.1. Sheet which the Crop Marks are printed.2. Blade3. Blade Holder
Set the Sheet and fix the Blade Holder with a blade tothe Carriage.
Set the Right & Left Pinch Rollers at the outsideof the Crop Marks.
Pinch Roller
Cutter ProtectionSet the sheet so that theCrop Marks are on theCutter Protection.
Power on the machine and press the [MENU/PARAM]key to enter the User's Mode.
Make sure that there is no illustration and stain onthis area.
Revised 4
4-17
4 Adjustment
4
MARK TEST
SELECT ROLL
[ENTER]
[ TEST ] + POWER ON
SELECT PIECE
CROPMARK I <AUTO>
SELECT I ROLL
CROPMARK I <OFF>
SELECT I ROLL
[MENU/PARAM]
CROPMARK I <OFF>
CROPMARK I <AUTO>
[ENTER]
6
4
5
Make sure that the [CROP MARKS] menu is set to[AUTO].
Factory Default : [OFF]In order to set to [AUTO], press the [MENU/PARAM]key to enter the Setting Mode and change it by theJog Dial.Then, press the [ENTER] key to save it.
<Confirmation> <Setting>
Power off the machine and power on again whilepressing the [TEST] key.Select [PIECE] and press the [ENTER] key.
The machine cuts around the Crop Marks.
Make sure that the Crop Marks are in the cut squares.If not, carry out the Crop Mark Sensor Adjustment.
4-18
4 Adjustment
4
4-9 AUTO CROP MARK SENSOR ADJUSTMENT (Referential Time : 20 min.)
This adjustment is for calibrating the distance from the center of the sensor to the tip of the pen.This adjustment can be performed by adjusting the cutting position to the Crop Marks which areprinted on the sheet with [CROP START] menu in the Service Mode.
Revised 4
1
2
3
Prepare the followings.1. Vinyl Sheet Size : A4
Color : Black (Backing should be white.)
2. Blade3. Blade Holder4. Tweezers
Turn on the power while pressing [ ], [ ], [ ]keys to enter the Service Mode.Select [CROP START] menu and press [MENU/PARAM] key to carry out the AUTO CROP MARKSENSOR ADJUSTMENT.
VERSION A100
PAUSE -> ENTER
CROP START
[MENU/PARAM]
[ ] [ ] [ ] + POWER ON
Set the Right & Left Pinch Rollers with 10cminterspace.Set the Sheet and fix the Blade Holder with a blade tothe Carriage.
4-19
4 Adjustment
4
6
4
5
Peel off this area.
Peel the sheet off leaving 2 squares after cutting.
Please carry out this without taking the sheet off.
Press [ENTER] key to continue the adjustment.
Sensor detects the center of the left square firstly anddetects the center of the right square.Then, the machine cuts inside of the right square.
Peel off the inside part of the right square and checkthat the line of the right square is not cut.
If it is cut, carry out the [4-10 Manual Crop MarkSensor Adjustment].
4-20
4 Adjustment
4
4-10 MANUAL CROP MARK SENSOR ADJUSTMENT (Referential Time : 20 min.) Revised 4
1 Turn on the power while pressing [ ], [ ], [ ]keys to enter the Service Mode.Select [CROP - *] menu and press [MENU/PARAM]key to enter the setting mode.
Select [CROP G] when adjusting the gritdirection.Select [CROP C] when adjusting the carriagedirection.
This adjustment can be done more precisely than the Auto Crop Mark Sensor Adjustment.This adjustment can be performed from [CROP G] & [CROP C] menus in the Service Mode.
VERSION A100
[ ] [ ] [ ] + POWER ON
[MENU/PARAM]
CROP < -29>
CROP < -29>*
*
[ENTER]
CROP G < -40 >
CROP G < -50 >
[ENTER]
CROP C < 25 >
CROP C < 45 >
When adjusting the cutting position to the right/ up, the parameter is [+].When adjusting the cutting position to the left/ down, the parameter is [-].
Change the parameter with the Jog Dial and press[ENTER] key to save it.
Parameter 1step = 0.05mm(Parameter 20 steps = 1mm)
In case of moving the Cutting Position down_about 0.5mm.
In case of moving the Cutting Position tothe right_about 1mm.
+ 20 steps
- 10 steps
4-21
4 Adjustment
4
3 Carry out [4-8 CROP MARK SENSOR CHECK].
5-1
5 Supplemental Information
5
5-1 OPERATIONAL SEQUENCE 5 Supplemental Information
DRAM CHECK
Power SW ON
NG
OK
Stop the movement.
Copy Firmware to DRAM.
Carriage moves to origin.
Ready to cut.
Motor Voltage
Detects origin
SHEET UNLOADED
NG
OK
Initialize Hardware.NG
OK
EEPROM ErrorEEROM CHECKNG
OK
Display Error Message
Roland DG Corp.Displays Opening Message.
Sensor ErrorNG
OKOrigin Error
Fan Error
Detects Media
SELECT RollDisplays Sheet Selection Menu.
ENTER
NG
OK
Err:Bad Posit ionDetects
PINCH ROLLER position.
NG
OK
Err:Sheet SetDetects Media length.NG
OK
When selecting PIECE
or
or
Display Error Message
Display Error Message
Display Error Message
Display Error Message
Display Error Message
Stop the movement.
OK
MARK1 NOT FOUNDDetects Crop Mark.
NGWhen CROP MARK isenable Display Error Message
Revised 4
5-2
5 Supplemental Information
5
5-2 SENSOR MAP
FRONT PAPER SENSOR (CX-24 ONLY)This sensor detects whether the Media is setor not. And also, it detects the front edge ofthe Media.Media has to be on this sensor when SETUP.
REAR PAPER SENSOR (CX-24 ONLY)This sensor detects whether the Media is set or not.And also, it detects the rear edge of the Media.Media has to be on this sensor when SETUP.
CARRIAGE LIMIT & PINCH ROLL SENSORThis sensor detects the Carriage Limit and thePinch Roller Position.
CROP MARK SENSORThis sensor detects the Crop Mark.
Revised 4
6-1
6 Troubleshooting
6
6 Troubleshooting6-1 START & END POINTS DON'T MATCH
Backlash Adjustment
Secure the Tool Carriage
Replace the Tool Carriage
Holder part of Tool Carriage is loose
Replace the Blade Holder
Bearing inside Blade Holder doesn't rotate smoothly
Blade tip is wearing out
Replace the blade
Match Offset
Blade Offset doesn't match with offset set in CX.
Motor Gear is meshed too tight or too loose
Tool Height is not correct Tool Carriage is loose
START & END POINTS DON'T MATCH
Tool Height Adjustment
Tool Pressure is not correct
Tool Pressure Adjustment
Blade Holder is set loose on Tool Carriage
Secure the Blade Holder
: Symptom : Check Points
: Action Number : Checking order
1
2 3
4
5
67
8
9
NO CHECKING POINT ACTION REFERENCE OUTLINE
1Blade Offset doesn't
match with offsetset in CX
Match Offset User's Manual
Blade used on the CX has offset and therefore, tip is shifted from itscenter. When the offset setting done on CX doesn't match with theblade offset, offset correction won't be done. Therefore, the startingand ending points won't match because the direction of the bladeslightly shifts from the correct direction.
2Blade Holder is setloose on ToolCarriage
Secure the BladeHolder User's Manual When Blade Holder is set loose on Tool Carriage, the blade tip
becomes very shaky when cutting and results in distorted figure.
3Blade tip is wearing
outReplace theBlade User's Manual
When blade tip wears out, offset will be changed. Therefore, as samesa1, the starting and ending point won't match especially whencutting circles.
4
Bearing insideBlade holderdoesn't rotatesmoothly
Replace theBlade holder
There are bearings inside the Blade Holder. When the bearings don'trotate smoothly, direction of the blade slightly shifts form the correctdirection and therefore, starting and ending points doesn't match.
5Holder part of ToolCarriage is loose
Replace the ToolCarriage
When holder part of Tool Carriage is loose, direction of the bladeslightly shifts from the correct direction and therefore, the startingand ending points won't match.
6Tool Carriage isloose
Secure the ToolCarriage
Section3 [ToolCarriage_Replacement]
When the Tool Carriage is loose, direction of the Tool Carriage slightlyshifts form the correct direction and therefore, the starting and ending pointswon't match.
7Tool Height is notcorrect
Tool HeightAdjustment
Section4 [ToolHeightAdjustment]
When Tool Height is not adjusted, blade hits the Bed strongly andbounces. Therefore, the cutting at the very beginning won't be doneand cause the starting and ending points to be shifted.
6-2
6 Troubleshooting
6
NO CHECKING POINT ACTION REFERENCE OUTLINE
8Tool Pressure is notcorrect
Tool pressure isnot
Section4 [ToolPressureAdjustment]
When Tool height is not adjusted, blade hits he Bed strongly andbounces. Therefore, he cutting at the very beginning won't be doneand cause the starting and ending points to be shifted. And also,when the Tool Pressure is set too high by the user, the blade offsetchanges because the blade tip goes deep into the sheet. Therefore,the starting and ending points will be shifted.
9Motor Gear ismeshed too tight ortoo loose
BacklashAdjustment
When Motor Gear is meshed too tight or too loose, Tool Carriageand Grit Roller will be driven unstable and results in starting andending points to shift.
6-3
6 Troubleshooting
6
6-2 STITCH CUT
Solenoid Driver IC on Main Board is broken STITCH CUTReplace IC14 on
Main Board
Replace the Blade
Blade tip is wearing out / cracks
Bearing inside Blade Holder doesn't rotate smoothly
Replace the Blade Holder
Tool doesn't move up/down smoothly
Replace the Tool Carriage
Scratch in Cutter Protection
Replace the Cutter Protection
Holder part of Tool Carriage is loose
Replace the Tool Carriage
Tool Carriage is set loose
Secure the Tool Carriage
Tool Height is not correct
Tool Height Adjustment
Tool Pressure is not correct
Tool Pressure Adjustment
1
2 3
4
5
67
8
9
NO CHECKING POINT ACTION REFERENCE OUTLINE
1Blade tip is wearing
out / cracksReplace theBlade
When blade wears out and cracks, it will be caught by the sheet andresults in stitch cut.
2
Bearing insideBlade holderdoesn't rotatesmoothly
Replace theBlade Holder
There are bearing s inside the Blade Holder. When the bearingsdon't rotate smoothly, direction of the blade slightly shifts from thecorrect direction and therefore, it will be caught by the sheet whichresults in stitch cut.
3Tool doesn't moveup/down smoothly
Replace the ToolCarriage
Section3 [ToolCarriage_Replacement
When Tool doesn't move up and down smoothly, blade sometimeshits the Bed strongly and bounces which results in stitch cut. In mostcases, stitch cut at the beginning is caused by this reason.
4Scratch in CutterProtection
Replace theCutter Protection
Section3 [CutterProtection_Replacement
Cutter Protection is where the blade lands for cutting. If there isscratch in the Cutter Protection, blade is caught by the sheet becauseit sticks deeper into the sheet and results in stitch cut.
5Holder part of ToolCarriage is loose
Replace the ToolCarriage
Section3 [ToolCarriage_Replacement
When holder part of Tool Carriage is loose, direction the bladeslightly shifts from the correct direction and therefore, it will becaught by the sheet which results in stitch cut.
6Tool Carriage is
looseSecure the Tool
CarriageWhen the Tool Carriage is loose, the blade tip becomes shaky and itwill be caught by the sheet which results in stitch cut.
7Tool Height is notcorrect
Tool HeightAdjustment
Section4 [ToolHeightAdjustment]
When Tool Height is not adjusted, blade hits the Bed strongly andbounces which results in stitch cut. In most cases, stitch cut at thebeginning is caused by this reason.
8Tool Pressure is notcorrect
Tool PressureAdjustment
Section4 [ToolPressureAdjustment]
When Tool Pressure is not adjusted, blade hits the Bed strongly andbounces which results in stitch cut.
9Solenoid Driver ICon Main Board isbroken
Replace IC14 onMain Board
When Solenoid Driver IC breaks, sometimes high pressure will begenerated. In this case, blade hits the Bed strongly and bounceswhich results in stitch cut.
6-4
6 Troubleshooting
6
6-3 MEDIA SHIFTING
Grit Roller is dirty
Sheet is not set correctly
Screw fixing the Plate Shaft is loose
MEDIA SHIFTING
Fan revolution
Refer to Troubleshooting FAN REVOLUTION 6-5
Secure the screw fixing the Plate Shaft
Set the sheet again and explain to user
Pieces of Media
Cleaning
Clean the Grit Roller
Pinch Roller is wearing out /broken
Replace the Pinch Roller
12
Driver IC on Main Board is broken
Replace IC12/13 onMain Board
7
65
4
3
NO CHECKING POINT ACTION REFERENCE OUTLINE
1Sheet is not set
correctly
Set the sheetagain and
explain to user
The most effective measure against media shifting is to set the mediastraight to the machine. Small tilting of the media when setting it upcould result in big shifting especially doing long print. It isrecommended to setup the media by adding tension towards front andcheck the shifting by prefeed function before actually start cutting.
2Pinch Roller iswearing out /
broken
Replace thePinch Roller
Section 3 [PinchRoller_Replacement]
When pinch rollers wear out, power to hold the media will beweakened and results in media shifting.
3 Pieces of Media CleaningWhen dust such as pieces of media is stick to the feeding place,making contact with the dust during the cutting and results in mediashifting.
4 Grit Roller is dirty Clean the GritRoller
When dust such as pieces of Media is stick to the grit roller, power tohold the sheet will be weakened and results in media shifting. Usebrush to clean the Grit Roller.
5Screw fixing the
Plate Shaft is loose
Secure the screwfixing the Plate
Shaft
When the screw fixing the Plate Shaft is loose, the pinch rollerdoesn't push the grit roller with the correct pressure and results inmedia shifting.
6 Fan revolution
Refer toTroubleshooting
FAN REVOLUTION6-5
When Fan is not rotate correctly, it doesn't suck the media to theApron and the media lifts up at the Bed and results in media shifting.
7Driver IC on MainBoard is broken
Replace IC12/ 13on Main Board
Motor Driver IC is a chip to supply the current to drive the motor.When it is broken, motor doesn't supply the correct current and themotor doesn't move correctly and results in media shifting.
6-5
6 Troubleshooting
6
6-4 PEN UP/DOWN ERROR
Cut-line in solenoid coil
Cut-line in Carriage Cable
Cable is not connected correctly
PEN UP/DOWN ERROR
Tool Pressure is not correct
Tool Pressure Adjustment
Load on the carriage up/down movement
Solenoid Driver IC on Main Board is broken
Replace the Carriage Cable
Replace the Tool CarriageConnect the cable again
1 2
3
45
6
Replace IC14 on Main Board
Replace the Tool Carriage
NO CHECKING POINT ACTION REFERENCE OUTLINE
1Cut-line in
Carriage CableReplace the
Carriage CableWhen there is cut-line in the carriage cable, the current is notsupplied from Main Board to Solenoid and the carriage doesn't move.
2Load on the
carriage up/downmovement
Replace the ToolCarriage
Section3 [ToolCarriage_Replacement
When the media is jammed, the carriage hits the jammed media andresults in the position of the solenoid shifting. The mechanical loadby rubbing the coil and bobbin cause the tool up/down error.
3Solenoid Driver ICon Main Board is
broken
Replace IC14 onMain Board
When the Solenoid Driver IC is broken the current is not supplied tosolenoid and result in tool up/down error.
4Cut-line in solenoid
coilReplace the Tool
Carriage
Section3 [ToolCarriage_Replacement
When there is cut-line in solenoid coil, there is no function aselectrical magnet because of no current and results in tool up/downerror.
5Cable is not
connected correctlyConnect thecable again
When there is a bad contact on the connector or cable, the signal isnot sent and cause tool up and down error.
6Tool Pressure is not
correctTool PressureAdjustment
Section4[Tool PressureAdjustment]
When Tool Pressure Adjustment is not done correctly (the value ofthe MIN pressure is lower that the correct one), there is a case thetool doesn't down.
6-6
6 Troubleshooting
6
6-5 FAN REVOLUTION
Fan Motor is broken
Replace the Main Board
CPU and Q1/Q2 on Main Board is broken
Replace the Fan Motor
FAN REVOLUTION
1 2
3
Bad contact in connector
Connect the connector again
NO CHECKING POINT ACTION REFERENCE OUTLINE
1Bad contact in
connectorConnect the
connector againWhen there is bad contact in connector, the signal doesn't passand results Fan Motor doesn't rotate.
2CPU and Q1/Q2 on
Main Board isbroken
Replace theMain Board
Fan Motor is controlled by CPU on the Main Board and sendthe signal to Q1/Q2. If the CPU or Q1/Q2 is broken, it doesn'tcontrol correctly and cause the Fan Motor rotation error.
3Fan Motor is
brokenReplace the Fan
Motor
Fan Motor used CX doesn't need to replace normally, howeverthere is a possibility the motor doesn't rotate because wearingout. Therefore, if there is no problem in the above 1 or 2,replace the Fan Motor to check.
7-1
7 Service Activities
7
7-1 INSTALLATION CHECK LIST 7 Service Activities
CX-24/12 INSTALLATION CHECK LIST
Power cord: 1 Roland Software Package CD-ROM: 1
Roller base: 1 Blade : 1
Blade holder(XD-CH3) : 1
Startup manual: 1 To Ensure Safe Use: 1
* CX-24 only
Pin
Accessories
Connection
Cables are available separately.One which you are surematches the model of computerbeing used should be selected.
For IBM PC or PC compatibles
Serial (RS-232C) cable
Parallel (Centronics) cable
Printer connector on the computerRS-232C connector on the computer
Serial (RS-232C) InputConnector
Parallel (Centronics)Input Connector
Model Serial Number User Date CX-24 / CX-12
ClassificationPurchase Loan Unit Demo Unit Replacement
CX-24 : 950mm (W) x 500mm (L) x 300mm (H)CX-12 : 650 (W) x 500mm (L) x 300mm (H)
Minimum Space Required
7-2
7 Service Activities
7
For Macintosh
Crossover serial cable
Cables are available separately.
Printer Port
Modem Port
Connect to either port.
Serial Input Connector
Preparation
Power connector
Power cord
Power outlet
Connecting the Power Cord
Installing Blade (User's Manual 4-1)
Loading the Matelial (User's Manual 4-2)
Acceptable material widths
Width(horizontal dimension)
Length(vertical direction)
CX-2450 to 700 mm (1-15/16 to 27-3/4 in.)
For flat material, 100 mm or more; for roll material,no restrictionNo other restrictions (* Accuracy assured within arange of up to 1,600 mm (63 in.))
CX-1250 to 395 mm (1-15/16 to 15-1/2 in.)
No restrictions (* Accuracy assured within arange of up to 1,600 mm (63 in.))
Installing the Driver / Software (User's Manual 3-3 / Startup Manual)
Putting the Machine in the Setup State (User's Manual 4-3)
7-3
7 Service Activities
7
Making Menu Setting with the Control Panel (User's Manual 4-3)
Checking Material Feed (User's Manual 4-4)
Setting the Origin Point (User's Manual 4-6)
Port Setting (User's Manual 3-4)
Setting
Cutting Test (User's Manual 4-7)¥ Adjusting the Blade Force¥ Adjusting the Blade extension
Test
Performing a Self-test (User's Manual 5)
Operation
Downloading Cutting Data (User's Manual 4-8)
Removing the Material (User's Manual 4-9)
Apply the Completed Cut out (User's Manual 4-9)
When Cutting is Completed (User's Manual 4-10)
Plotting on Paper Media (User's Manual 6)
¥ Explain to the customer that since the design of the CX-24/12 differs inherently from that of dedicated plotters, it does notaccommodate functions such as high-speed plotting, automatic pen changes, pen dry protection, or the like.
Repeating the Same Cutting (User's Manual 7)¥ Preparing the Cutting Data¥ Getting Ready for Recutting
Repeating cutting without replacing the material.Repeating cutting on different material
¥ Performing Recutting
Model
CX-24
CX-12
Material shape selected from the menu
[ROLL]
[EDGE][PIECE]
There is no material-selection menu.
Location of the origin point
- Near the left pinch roller- Near the right pinch roller when the [ROTATE] menu
item is set to ON- At the front lower left of the material- Near the front lower right of the material when the
[ROTATE] menu item is set to ON- Near the left pinch roller- Near the right pinch roller when the [ROTATE] menu
item is set to ON
7-4
7 Service Activities
7
Others
Blade
ZEC-U1005
ZEC-U5025
ZEC-U1715
Material
General Signage Vinyl
General Signage VinylReflective VinylFluorescent Vinyl
Rubber material forsandblasting stencil
Tool-force
50 to 150 gf
30 to 100 gf120 to 200 gf100 to 200 gf
100 to 200 gf
Speed
40 cm/sec.
40 cm/sec.40 cm/sec.40 cm/sec.
10 cm/sec.
Amount of cutterblade extension
0.25 mm (0.01 in.)
0.25 mm (0.01 in.)0.25 mm (0.01 in.)0.25 mm (0.01 in.)
0.25 mm (0.01 in.)
Life of a blade(General guide)
8000 m (314960 in.)
4000 m (157480 in.)4000 m (157480 in.)4000 m (157480 in.)
Varies according tomaterial type
¥ The values for lifespan are intended to serve as a general guide when cutting materials of identical type.
Blade and Material Combinations (User's Manual 8-1)
Cutting Area (User's Manual 8-2)
Description of Display Menu (User's Manual 9-2)
Pinch roller (Right) Pinch roller (Right)
Cutting Area
Material
Pinch roller (Left) About 1 mm(about 0.04in.)
Initial cutting coordi-nate origin point (0,0)
Abou
t 15
mm
(abo
ut 9
/16
in.)
Max.584 mm (23 in.)
Max.280 mm (11in.)
Max
.24,
998
mm
(984
-1/8
in.)
(Acc
urac
y as
sure
d w
ithin
a ra
nge
ofup
to 1
,600
mm
(63
in.))
Max
. 24,
998
mm
(984
-1/8
in.)
(Acc
urac
y as
sure
d w
ithin
a ra
nge
ofup
to 1
,600
mm
(63
in.))
<CX-24> <CX-12>
7-5
7 Service Activities
7
MECHANICAL PARTS
LUBRICATION
FUNCTION CHECK
Date : . . .
7-2 MEINTENANCE CHECK LIST
CX-24/12 MAINTENANCE CHECK LIST
Model Serial No.CX-24CX-12
ConfirmationCarriage Driving Part 1. Drive Gear Dirt / Crack
2. Backlash LoosenessGrit Driving Part 1. Drive Gear Dirt
2. Backlash Looseness3. Grit Roller Foreign substance
Bed/Guide Rail 1. Pinch Roller Rotation 2. Cutter Protection Dirt / Scratch
(Replacement depend on the scratch.)Carriage 1. Carriage Looseness
2. Cutter Holder LoosenessCutter Pen 1. Bearing Rotation of the Bearing
Check Points
ConfirmationFloil G-474C Carriage Drive Gear
Grit Drive Gear
Check Points
Confirmation1. Firmware Version Replace the Firmware to the latest version2. Carriage & Grit Compensation3. Cutting Test Wavy line
Distorted figurePen BouncingNoiseTool PresureMedia ShiftingQuality of corners
4. Connection check with Customer's PC.
Check Points
7-6
7 Service Activities
7
7-3 SPECIFICATION
*..... CX-24 only
Driving methodMaximum cutting area
Acceptable media widthsAcceptable paper widthsAcceptable paper typesTools
Max. cutting speed
Blade forceMechanical resolutionSoftware resolutionDistance accuracyRepetition accuracy
InterfaceBuffer sizeInstruction systemSwitchesControl switchesDisplayPower consumptionAcoustic noise level
Dimensions
WeightOperating temperatureOperating humidityAccessories
Width: 584 mm (22-15/16 in.)Length: 24,998 mm (984-1/8 in.)50 to 700 mm (1-15/16 to 27-1/2 in.)50 to 700 mm (1-15/16 to 27-1/2 in.)
Media-movement method Stepping motor (Micro-step)
Width: 280 mm (11 in.)Length: 24,998 mm (984-1/8 in.)50 to 395 mm (1-15/16 to 15-1/2 in.)50 mm to 395 mm (1-15/16 to 15-1/2 in.)
High-quality paperCutters: Special cutter for CAMM-1 seriesPens: Water-based fiber-tipped pens, and Thick water-based fiber-tipped pens (options)During cutting: 400 mm/sec. (15-11/16 in./sec.) (45-degree direction)(when [HEAVY] is selected on the display menu: 100 mm/sec.(3-7/8 in./sec.))30 to 200 gf0.05 mm/step (0.00197 in./step)0.025 mm/step (0.000984 in./step)Error of less than +/- 0.2% of distance traveled, or 0.1 mm (0.00394 in.), whichever is grater0.1 mm (0.00394 in.) or less (Excluding stretching/contraction of the material,and provided that material length is under 1600 mm (62-15/16 in.))Parallel (Centronics compatible), Serial (RS-232C)1 Mbyte (800 Kbyte for replot buffer)CAMM-GLIII (mode1 and mode2)Power switchDial, TEST, ORIGIN, , , , , ENTER, MENU/PARAMLiquid crystal display unit: 16-character by 1 lineMaximum: 0.9 A /100 to 240 V ± 10 % 50/60 Hz[Cutting mode] : less than 70 dB (A) [Standby mode] : less than 40 dB (A)(According to ISO 7779)850 mm (W) x 300 mm (D) x 240 mm (H)(33-1/2 in. (W) x 11-13/16 in. (D) x 9-1/2 in. (H))14 kg (30.9 lb.)
545 mm (W) x 300 mm (D) x 240 mm (H)(21-1/2 in. (W) x 11-13/16 in. (D) x 9-1/2 in. (H))10 kg (22 lb.)
5 to 40¡C (41 to 104¡F)35 to 80% (non-condensing)Power Cord x 1, Blade (ZEC-1005) x 1, Blade Holder XD-CH3 (Cutter holder and pin) x 1,Startup Manual x 1, To Ensure Safe Use x1, Roland Software Package CD-ROM x 1, Roller base x1*
CX-24 CX-12
7-7
7 Service Activities
7
1
19
18
36
3.3K
+5 V
=*
Signal Terminal Signal Pin Connectionnumber number number
NC 36 18 HIGH*HIGH* 35 17 GNDNC 34 16 GNDGND 33 15 NCHIGH* 32 14 NCNC 31 13 HIGH*
30 12 GND29 11 BUSY28 10 ACK27 9 D726 8 D6
GND 25 7 D524 6 D423 5 D322 4 D221 3 D120 2 D019 1 STROBE
ParallelStandard In compliance with the specifications of CentronicsInput signals STROBE (1 BIT), DATA (8 BITS)Output signals BUSY (1 BIT), ACK (1 BIT)Level of input/output signals TTL levelTransmission method Asynchronous
SerialStandard RS-232C specificationsTransmission method Asynchronous, duplex data transmissionTransmission speed 4800, 9600 (Selected using panel keys.)Parity check Odd, Even, or None (Selected using panel keys.)Data bits 7 or 8 bits (Selected using panel keys.)Stop bits 1 or 2 bits (Selected using panel keys.)Handshake Hardwire (power on) or XON/XOFF (Selected using panel keys.)
Parallel connector (in compliance with specifi-cations of Centronics)
Serial connector (RS-232C)
1
14
13
25
Signal Terminal Signal Pin Connectionnumber number number
NC 25 13 NCNC 24 12 NCNC 23 11 NCNC 22 10 NCNC 21 9 NCDTR 20 8 NCNC 19 7 SGNC 18 6 DSRNC 17 5 CTSNC 16 4 RTSNC 15 3 RXDNC 14 2 TXD
1 FG
CX-24 / 12