custom seat cover installation guide - truck accessories
TRANSCRIPT
1
Custom Seat Cover Installation Guide
De�ning Custom Accessories
All pictures, diagrams & text, copyright 2009 Shrin Corporation
2
Index
Custom Seat Cover Installation 3Removing a Headrest 4Backrest Cover Installation 7Seat Bottom Cover 10Solid Bench 11Console Cover Installation 12Special Instructions - 1 13Special Instructions - 2 14Finishing Touches 15
Also Available
Custom Car Cover
Custom Sunshield
Custom Dashboard Cover
Custom Floor Mats
Custom Seat Cover
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
3
Custom Seat Cover Installation
Custom Seat Cover Installation
Buckets
Bucketswithout Headrests
Bucketswith Seatbelts
60/40 Split Bench
60/40 Split Benchwith Integrated Belts
60/40 Split Bench
Split Benchwith Integrated Belts
Solid Bench
Solid Benchwith Headrests
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
4
Removing a Headrest
All pictures, diagrams & text, copyright 2009 Shrin Corporation
ab
© 2009 SHRIN CORPORATION
5
Removing a Headrest
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
in oles
.
lot ab
6
Pin Hole and TabInsert a paperclip end into the hole on the side of headrest base. While pressing the paper clip, pressthe tab on the other base; while pressing both, liftthe headrest. This requires two or more people.
Removing a Headrest
Removing a Headrest
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
7
Backrest Cover Installation
Backrest Cover InstallationBucket Seats with Non-Removable Headrest
Backrest Cover InstallationCertain Seats Required to be FoldedForward for Proper Installation.
Tip: Fold the seatback forward to gain betteraccess while passing the �ap through.
Attach velcro to the �ap which is passed through theopening between seatback and seat bottom.
All pictures, diagrams and text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
8
Backrest Cover InstallationBucket Seats with Integrated Seat Belts
Backrest Cover InstallationHigh-Back Bucket Seats
Tip: See Finishing Touches, pg. 15, forcleaner headrest post �nishing.
A�x velcro.
Tip: Fold the seatback forward to gain better access while passing the �ap through.
Pass �ap through the opening betweenseatback and seat bottom, then attach velcro.
Tip: Fold the seatback forward to gainbetter access while passing the �apthroughthe seatback and seat bottom.
Backrest Cover Installation
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
9
Backrest Cover Installation
Backrest Cover Installation60/40 Split Bench
Backrest Cover InstallationSpecial - for Older Jeep Models
See Removing a Headrest, pgs. 4-6,on removing headrests.
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
Tip: Fold the seatback forward to gain better
seatback and seat bottom, then attach velcro.
10
CD
A BC
D
E
ABC
D
E
A B
C D
A BC D
A, B
A, B
E
E
Seat Bottom CoverTip: Fold the seatback forward to gain betteraccess while passing the �ap through.
Position cover over seat bottom. Pass �apthrough and attach buckles and hooks.
Tip: Tuck excess material behind plastictrim pieces for an extra custom look.
Note: Some seat bases are not covered.
or
Seat Bottom Cover
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
11
Solid Bench
C
AAC
B
DB
D
AC AC
E
BB
D
D
AC
BD
C
D
A, B
A, B
E
E A, BE
Follow these simple instructions if you have a solid bench seat(made for three people, with and without headrests).
Solid Bench
Place backrest cover over backrest. If the seat has a folding armrest, place it in the “up” position.If seat has headrests, remove headrests prior to installation (see Headrest Removal, pgs. 4-6).
Tuck �ap through the opening between seatback and seat bottom.
Place seat bottom cover over seat bottom and a�x straps.
See Finishing Touches, pg. 15, for extra tips.
Tip: Fold the seatback forwardfor easier access.
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
12
A B
C D
A B
C D
E EA B
A B
A BE
E
ABC
D
E
A
B
C
E
Open console.
Cover console top,then console bottom.
Pass console bottom �apthrough opening, then a�xvelcro.
Console Cover Installation
Console Cover Installation
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
13
Special Instrustions -1
A
C
D
B
A
B
C
DSeats with airbags, lumbar supports and armrestsrequire special instructions.
Special Instructions -1
Seats with integrated seat airbags must be covered only with seat coversdesigned with opening �aps. The �ap inserts inside the cutout, and shouldbe able to open freely in case of deployment.
If your vehicle has seat-mounted airbags, be certain that the seat covershave airbag cutouts or �aps! DO NOT COVER SEAT AIRBAGS!
Some levers or controls may require a slit in the seat cover.
Installing backrest cover around armrests.
Installing armrest covers and a�xing velcro.
All pictures, diagrams & text, copyright 2009 Shrin Corporation
1
2
© 2009 SHRIN CORPORATION
14
Special Instructions - 2
1. An elastic strap holds the �ap of fabric to some permanently mounted hooks. To remove, simply pull the the elastic forward and remove the elastic loop from the hook.
2. Metal hoops hold the �ap of fabric to a steel support under the seat. To remove, use a set of pliers to open the hoop, and remove the fabric.
The views shown below are of the bottom of the seat.
Pliers required.
Special Instrustions -2
All pictures, diagrams & text, copyright 2009 Shrin Corporation
© 2009 SHRIN CORPORATION
Certain late-model vehicles, including Lexus, Toyota, In�niti, Nissan,Hyundai and others, have a piece of fabric which prevents the seat cover�ap from going through the opening of the seatback and seat bottom.
This �ap will need to be removed to install the seat cover. Beloware instructions detailing the methods used to remove this fabric.
15
Finishing Touches
A
B
C
D
If you have extra time and a little mechanical know-how,your seat covers can �t even better by following thesesimple �nishing touches:
Finishing Touches
Material around the headrest posts can be stretched over the base and tucked underneath.
Adjust material around armrests by tucking excessivematerial around the base.
Pay special attention to small levers, such as lumbar support. Material should be tucked under the lever.
Tip: Fold the seatback forwardfor easier access.
All pictures, diagrams & text, copyright 2009 Shrin Corporation
A
B
C
D
© 2009 SHRIN CORPORATION
or
After the �rst two weeks of use, tighten the seatback covers by releasing them, and--using the assistance ofanother person--pull the material very tight and a�x the velcro fastener.
Toll Free: 800.COVERKINGFax: 714.850.0828
900 E. Arlee PlaceAnaheim, CA 92805
Coverking.com
All pictures, diagrams & text, copyright 2009 Shrin Corporation
Tel: 714.850.0303