curtain walls aluminum - crl-arch · curtain walls j j6 technical data aluminum series width depth...

01-J6

CURTAIN WALLS

J6

Table of Contents

J

ALUMINUM

SECTION J6 PAGE

SPECIFICATIONS ................................................................................................................................02-J6 and 03-J6

TECHNICAL DATA ................................................................................................................................................04-J6

SPECIAL FEATURES ............................................................................................................................................05-J6

TYPICAL DETAILS ..............................................................................................................................06-J6 thru 13-J6

WINDLOAD CHARTS ..........................................................................................................................14-J6 and 15-J6

DEADLOAD CHARTS ............................................................................................................................................16-J6

ACCESSORIES ..................................................................................................................................17-J6 and 18-J6

Due to the diversity in state/provincial, local, and federal laws and codes that govern the design and application of architectural products, it is the responsibility of the individual architect, owner, and installer to ensure that products selected for use on projects comply with allapplicable building codes and laws. U.S. Aluminum exercises no control over the use or application of its products, glazing materials, andoperating hardware, and assumes no responsibility thereof.

The rapidly changing technology within the architectural aluminum products industry demands that U.S. Aluminum reserve the right to revise,discontinue or change any product line, specification or electronic media without prior written notice.

NOTE: Dimensions in parentheses ( ) are millimeters unless otherwise noted.Other metric units shown in this publication are: m - meter Kg - kilogramPa - pascal KPa - kilopascalMPa - megapascal

Project: TAP Holdings; Deerfield, IL

Online usalum.com By Phone (800) 262-5151 Ext. 5305Online crlaurence.com By Phone (800) 421-6144 Ext. 5305

Thermally Broken• Series 4250T

Non Thermal• Series 4250

SERIES 4250TThermally Broken InteriorGlazed Curtain Wall

SERIES 4250Non Thermal InteriorGlazed Curtain Wall

02-J6

CURTAIN WALLS

J

J6

SpecificationsALUMINUM

SERIES FACE WIDTH DEPTH GLAZING INFILL GLAZING METHOD4250T 2-1/2" (63.5) 6" (152.4) 1" (25) and/or 1/4" (6) Interior

I. GENERAL DESCRIPTIONWork Included: Furnish all necessarymaterials, labor, and equipment for the complete installation of aluminumframing as shown on the drawings andspecified herein. (Specifier Note: It issuggested that related items such asaluminum entrance doors, glass, andsealants be included whenever possible.)Work Not Included: Structural supportof the framing system, interior closures,trim (Specifier list other exclusions).Related Work Specified Elsewhere:(Specifier list).

QUALITY ASSURANCEDrawings and specifications are basedon the Series 4250T Thermal CurtainWall System as manufactured by U.S. Aluminum. Whenever substituteproducts are to be considered,supporting technical literature, samples,drawings and performance data mustbe submitted 10 days prior to bid inorder to make a valid comparison of theproducts involved.

PERFORMANCE REQUIREMENTSAir Infiltration: shall be tested inaccordance with ASTM E 283.Infiltration shall not exceed .06 CFM per square foot (.0003m3/sm2) of fixedarea when tested at 6.24 psf (300 Pa).Water Infiltration: shall be tested inaccordance with ASTM E 331. No water penetration at test pressure of 12 psf (574 Pa). Structural Performance: shall betested in accordance with ASTM E 330and based on:• Maximum deflection of L /175 of thespan

• Allowable stress with a safety factor of 1.65

The system shall perform to this criteriaunder a windload of (Specify) psf.System shall exceed maximum seismiclateral displacement requirementsspecified in section 1628.8.2 of theUniform Building Code, 1994 edition.Upon successful completion of thePhase I seismic testing, the curtain wallshall once again be subjected to andmust successfully pass the air andwater infiltration tests specified above

before proceeding to Phase II testing.Structural Integrity - Manufacturer shallprovide a Two Year Warranty on thermalframing against failure resulting from thefollowing:• Longitudinal or transverse thermalbarrier shrinkage.

• Thermal barrier cracking.• Structural failure of the thermal barrier material.

• Loss of adhesion or loss ofprescribed edge pressure on theglazed material resulting in excessiveair and water infiltration.

Thermal Performance: Series 4250Tshall be tested in accordance withAAMA 1503, and NFRC-100.Testing Procedures:ASTM 283, E 331, and E 330 -Laboratory performance testing. AAMA503-08 - Newly installed curtain wall.AAMA 511-08 - Installed curtain wallafter six months.

II. PRODUCTS MATERIALSExtrusions shall be 6063-T5 alloy andtemper (ASTM B221 alloy T5 temper),thermally broken by a two partchemically cured high densitypolyurethane. To ensure that compositestrength remains unaltered duringthermal cycling, a mechanical bondbetween the aluminum and the thermalfilling shall be created by mechanicallyabrading the extrusion thermal cavityprior to filling with the polyurethanepolymer. Fasteners, where exposed,shall be aluminum, stainless steel orzinc plated steel in accordance withASTM A 164. Perimeter anchors shallbe aluminum or steel, providing thesteel is properly isolated from thealuminum. Glazing gaskets shall beE.P.D.M. elastomeric extrusions.

FINISHAll exposed framing surfaces shall befree of scratches and other seriousblemishes. Aluminum extrusions shallbe given a caustic etch followed by ananodic oxide treatment to obtain…(Specify one of the following):_____#11 Clear anodic coating_____#22 Dark Bronze anodic coating_____#33 Black anodic coating

A Fluoropolymer paint coatingconforming with the requirements ofAAMA 2605. Color shall be (Specify a U. S. Aluminum standard color).

FABRICATIONThe curtain wall system shall provide for both vertical and horizontal membersto project a maximum of 3/4" (19) to theexterior. Provisions shall be made atsealed horizontals to weep moistureaccumulations to the exterior. Spandrelhorizontals shall feature a gutter to collectmoisture and weep it to the exterior.Vertical and horizontal components shallbe designed for complete inside glazingof spandrel and vision glass. Provisionsshall be made for re-glazing of spandrelfrom exterior without removal of visionlights. Vertical splices shall be designedto provide adequate space for thermalexpansion. Splice sleeves will ensure the seal and weatherability of the splicejoints. System shall provide forexpansion and contraction of componentmaterials as will be required by anambient temperature range of 120degrees F (49°C) without causing harmfulbuckling or cracking, opening of joints,undue stress on fasteners or other effectsdetrimental to weathering performance.The system shall accommodate 1" (25)infill with provision for 1/4" (6) infill atspandrel areas.

III. EXECUTION INSTALLATIONAll glass framing shall be set in correctlocations as shown in the details andshall be level, square, plumb, and inalignment with other work in accordancewith the manufacturer’s installationinstructions and approved shopdrawings. All joints between framing andthe building structure shall be sealed inorder to secure a watertight installation.

PROTECTION AND CLEANINGAfter installation the General Contractorshall adequately protect exposedportions of aluminum surfaces fromdamage by grinding and polishingcompounds, plaster, lime, acid, cementor other contaminants. The GeneralContractor shall be responsible for finalcleaning.

SpecificationsSECTION 08 44 13 ALUMINUM CURTAIN WALL SYSTEMS



03-J6

CURTAIN WALLS

J6

Specifications Non Thermal• Series 4250

J

ALUMINUM

SECTION 08 44 13 ALUMINUM CURTAIN WALL SYSTEMS

SERIES FACE WIDTH DEPTH GLAZING INFILL GLAZING METHOD

4250 2-1/2" (63.5) 6" (152.4) 1" (25) and/or 1/4" (6) Interior

I. GENERAL DESCRIPTIONWork Included: Furnish all necessarymaterials, labor, and equipment for thecomplete installation of aluminumframing as shown on the drawings andspecified herein. (Specifier Note: It issuggested that related items such asaluminum entrance doors, glass, andsealants be included wheneverpossible.)Work Not Included: Structural supportof the framing system, interior closures,trim. (Specifier list other exclusions).Related Work Specified Elsewhere:(Specifier list).

QUALITY ASSURANCEDrawings and specifications are basedon the Series 4250 Curtain Wall Systemas manufactured by U.S. Aluminum.Whenever substitute products are to beconsidered, supporting technicalliterature, samples, drawings, andperformance data must be submitted 10days prior to bid in order to make avalid comparison of the productsinvolved. Test reports certified by anindependent test laboratory must bemade available upon request.

PERFORMANCE REQUIREMENTSAir Infiltration: shall be tested inaccordance with ASTM E 283.Infiltration shall not exceed .06 CFM persquare foot (.0003m3/sm2) of fixed areawhen tested at 6.24 psf (300 Pa).Water Infiltration: shall be tested inaccordance with ASTM E 331. No water penetration at test pressure of12 psf (574 Pa).Structural Performance: shall betested in accordance with ASTM E 330and based on:• Maximum deflection of L /175 of thespan

• Allowable stress with a safety factor of 1.65

The system shall perform to this criteriaunder a windload of (Specify) psf.

System shall exceed maximum seismiclateral displacement requirementsspecified in section 1628.8.2 of theUniform Building Code, 1994 edition.Upon successful completion of thePhase I seismic testing, the curtain wallshall once again be subjected to andmust successfully pass the air andwater infiltration tests specified abovebefore proceeding to Phase II testing.Testing Procedures:ASTM 283, E 331, and E 330 -Laboratory performance testing. AAMA503-08 - Newly installed curtain wall.AAMA 511-08 - Installed curtain wallsafter six months.

II. PRODUCTS MATERIALSExtrusions shall be 6063-T5 alloy andtemper (ASTM B221 alloy T5 temper).Fasteners, where exposed, shall bealuminum, stainless steel or zinc platedsteel in accordance with ASTM A 164.Perimeter anchors shall be aluminum orsteel, providing the steel is properlyisolated from the aluminum. Glazinggaskets shall be E.P.D.M. elastomericextrusions.

FINISHAll exposed framing surfaces shall befree of scratches and other seriousblemishes. Aluminum extrusions shallbe given a caustic etch followed by ananodic oxide treatment to obtain…(Specify one of the following):_____#11 Clear anodic coating_____#22 Dark Bronze anodic coating_____#33 Black anodic coatingA Fluoropolymer paint coatingconforming with the requirements ofAAMA 2605. Color shall be (Specify a U.S. Aluminum standard color).

FABRICATIONThe curtain wall system shall provide forboth vertical and horizontal members toproject a maximum of 3/4" (19) to theexterior. Provisions shall be made at

sealed horizontals to weep moistureaccumulations to the exterior.

Spandrel horizontals shall feature agutter to collect moisture and weep it to the exterior. Vertical and horizontalcomponents shall be designed forcomplete inside glazing of spandrel andvision glass. Provisions shall be madefor re-glazing of spandrel from exteriorwithout removal of vision lights. Verticalsplices shall be designed to provideadequate space for thermal expansion.Splice sleeves will ensure the seal andweatherability of the splice joints.System shall provide for expansion and contraction of component materialsas will be required by an ambienttemperature range of 120 degrees F(49° C) without causing harmful bucklingor cracking, opening of joints, unduestress on fasteners or other effectsdetrimental to weathering performance.The system shall accommodate 1" (25)infill with provision for 1/4" (6) infill atspandrel areas.

III. EXECUTION INSTALLATIONAll glass framing shall be set in correctlocations as shown in the details andshall be level, square, plumb, and inalignment with other work inaccordance with the manufacturer’sinstallation instructions and approvedshop drawings. All joints betweenframing and the building structure shall be sealed in order to secure awatertight installation.

PROTECTION AND CLEANINGAfter installation the General Contractorshall adequately protect exposedportions of aluminum surfaces fromdamage by grinding and polishingcompounds, plaster, lime, acid, cementor other contaminants. The GeneralContractor shall be responsible for finalcleaning.


04-J6

CURTAIN WALLS

J

J6

Technical DataALUMINUM

SERIES WIDTH DEPTH GLAZING INFILL APPLICATIONS

4250T4250

2-1/2" (63.5) 6" (152.4)1" (25) and/or

1/4" (6)

Low-Rise to Mid-Rise Buildings Where Interior Glazing is Desired.

Series 4250T Curtain Wall is a stick-erected, interior-glazed curtain wall utilizing a pocket setdesign and E.P.D.M. compression glazing gaskets. This system features the Poly-Aluminizer™

thermal break technology. It was specifically engineered to satisfy the increasing demands forenergy conservation. Dual colors can be achieved by specifying different finishes for theexterior face covers and the interior mullions. Two piece horizontals and shear blocks allow fora concealed horizontal to vertical joinery without exposed screws. These joint intersectionsalso have concealed injection molded end dams for controlling any infiltrated water.

NOTE: Series 4250 offers the same features, except it is not thermally broken.

SERIES 4250T Thermally Broken Interior Glazed Curtain Wall

GLASS SIZES*

Glass Width and Height = Daylight Opening + 15/16" (23.8)

* These formulae do not take into account glass tolerances. Consult glass manufacturer before ordering glass.




SERIES 4250 Non Thermal Interior Glazed Curtain Wall

05-J6

CURTAIN WALLS

J6

Special Features

J

ALUMINUM

Top and Bottom "T"Expansion Anchors

WD600End Dam

Snap-In Cover

Install Injection Molded Closure Plates at top and bottom of verticals to ensure a continuous perimeter seal.

Slide top and bottom "T" Anchors into vertical mullions. Install vertical mullions plumb and level. Secure top and bottom "T" Anchors to structure. See page 17-J6 for additional information.

Injected Molded End Dams are for controlling anyinfiltrated water. Apply sealant to the four contact sidesof end dams and slide between vertical and horizontaljoint as shown. See page 17-J6 for additionalinformation.

Sill Members are designed with Snap-In Covers to conceal fasteners.

Head and intermediate horizontal mullions are also designed to conceal the fasteners which attach to the Shear Block. See page 17-J6 for additional information.

NOTE: To accelerate installation times with pinpoint accuracy of Horizontal Shear Blocks to Curtain Wall Mullions see pages 56-P1 and 57-P1.

CP600Closure Plate




Shear Block

VERTICAL MULLIONSFOR 1" (25) GLAZING

06-J6

CURTAIN WALLS

J

J6

Typical DetailsALUMINUM

SERIES 4250TThermally Broken Interior GlazedCurtain Wall

NOTE: Part numbers shown areavailable in 24' (7.3 m) stock lengths.Visit usalum.com for more information.

NOT TO SCALE




HEAVY WALL VERTICALS

PT610PW610

PT610PW610

PT600PW600

PT600PW600

PT600PW600

TYPICAL ELEVATION

SS964Steel Stiffener

PW612

PW612

PW612 PW6121/2"(12.7)

1/2"(12.7)

Caulking Joint (Typ.)

3/4"(19.1)

PW612

PT618PW618

PT618PW618

2-1/2"(63.5)

6"(152.4)

D.L.O. 2-1/2"(63.5)

2-1/2"(63.5)

D.L.O.

FRAME WIDTH

ROUGH OPENING

Two digit Part Number prefixending in "T" representsTHERMALLY BROKEN parts.Thermal parts are in BOLDprint. 4250T details aretypically shown.

P T 6 0 0

1 2

1

1

2 2

2

07-J6

CURTAIN WALLS

J6

Typical Details

J

ALUMINUM

HORIZONTAL MULLIONSFOR 1" (25) GLAZING






Top and Bottom Anchor(See page 17-J6 forProper Part Numbers)

NOT TO SCALE

NOTE: The PW613 Beveled FaceCap (Shown) is Standard forHorizontal Members. The CW901Square Face Cap is Optional.

TYPICAL ELEVATION

1

2

2

3

1

2

3


P T 6 0 0

PT603PW603

PW607

PT604PW604

PW607

PT606PW606

Top and Bottom Anchor(See page 17-J6 forProper Part Numbers)

AP603Shear Block

CP600Closure Plate

CP600Closure Plate

PW602Snap-In Cover

PW613

PW613

PW613

NP425(Typ.)

NP426(Typ.)

1/2"(12.7)

1/2"(12.7)

D.L.O.

2-1/2"(63.5)

2-1/2"(63.5)

2-1/2"(63.5)

6"(152.4)

D.L.O.

FRAME HEIGHT

ROUGH OPENING

DOOR FRAMING

08-J6

CURTAIN WALLS

J

J6



D.O.

NOTE: Door Frames are available in stock to accommodate 36" x 84" (914 x 2134) and 72" x 84" (1829 x 2134) door openings. Visit usalum.com for more information.

NOT TO SCALE




ThresholdTH014

12

PW612

PW613

NP425(Typ.)

NP626(Typ.)

D-201

D-101

M-550

M-550

D-201

D-101

M-550

M-550

CENTER HUNG DOOR

PT600PW600

TJ450P-050

PT618PW618

JC457P-427

PT604PW604

PT618PW618

6"(152.4)

1/8"(3.2)

1/16"(1.6)

1"

(25.4)

1-3/4"(44.5)

D.O.

PW607

TH014 (TH017 for floor closer)

20101M17Center Hung Adjustable Closer105° N.H.O.

Top Portion ofCenter Pivot for SurfaceMounted orFloor CloserApplications

D.O.

1/8"(3.2)

1/8"(3.2)

PW613

J-450

PT604PW604

PT618PW618

1-3/4"(44.5)

PW607

1/8"(3.2)

1/8"(3.2)

1/2"(12.7)

1/2"(12.7)

3/16"(4.8)

3/16"(4.8)

Floor Closer Dotted

NOTE: The PW613 Beveled Face Cap (shown) is standard for HorizontalMembers. The CW901 Square Face Capis Optional.


P T 6 0 0

M-550

D-300

3

1

2

3

2

3

Threshold

09-J6

CURTAIN WALLS

J6

Typical DetailsDOOR FRAMING

J


ALUMINUM

NOT TO SCALE



PW607

1/16"(1.6)

PW612DT550M-550

NP626(Typ.)

NP425(Typ.)

DT550

M-550

PW613

OFFSET HUNG DOORPT600PW600

TJ450DS047

PT618PW618

JS467

DS047

D-201

M-550

D-101/M-550

D-101M-550

DA201

PT604PW604

PT618PW618

3/32" (2.4)1"

(25.4)

1-3/4"(44.5)

D.O.

D.O.

PW607

BW200Door SweepWith ConcealedFasteners

35083ContinuousGear Hinge

21201U CloserWith Offset Arm105° N.H.O.

D.O.1/16"(1.6)

PW612

PT600PW600

TJ450DS047

PT618PW618

3/8" (9.5)1"

(25.4)D.O.

1/8"(3.2)

4-1/2"(114.3) 6"

(152.4)

1/8"(3.2)

PW613

J-450

PT604PW604

PT618PW618

1-3/4"(44.5)

1/8"(3.2)

1/8"(3.2)

1/2"(12.7)

3/16"(4.8)

NOTE: The PW613 Beveled Face Cap(shown) is Standard for Horizontal Members. The CW901 Square Face Cap is Optional.


P T 6 0 0

12

3

NOTE: Door Frames are available in stockto accommodate 36" x 84" (914 x 2134)and 72" x 84" (1829 x 2134) door openings.Visit usalum.com for more information.

41

2

2

3

4

TH250 Threshold

90 DEGREE CORNER CONDITIONS

10-J6

CURTAIN WALLS

J

J6



P T 6 0 0


PT618PW618

PT631PW631

CW969

CW969

PT600PW600

Aluminum BrakeMetal Cover

Aluminum Angle

PT618PW618 PT600

PW600PW612

A-100

PW630

NP626(Typ.)

NP425(Typ.)

A-100

PW612

3-3/4"(95.3)

2-1/2"(63.5)

1/8"(3.2)

D.L.O.

FRAME WIDTH

NOT TO SCALE




11-J6

CURTAIN WALLS

J6

Typical Details

J

ALUMINUM

1" (25) TO 1/4" (6) TRANSITION GLAZING


NOT TO SCALE

4

5

6

7

TYPICAL ELEVATION

PW612

PW612(2) CW969

PT600PW600

PT631PW631

PT600PW600

2-1/2"(63.5)

2-1/2"(63.5)

2-1/2"(63.5)

2-1/2"(63.5)2-1/2"

(63.5)3-3/4"(95.3)

D.L.O.

D.L.O.

D.L.O.

FRAME HEIGHT

D.L.O.

DIMENSION POINT

PW614

PW614PW615 PW615

PW613

PW613

PW613

PW613

6"(152.4)

6"(152.4)

1/2"(12.7)

1/2"(12.7)

CP600Closure Plate

PT603PW603

PT605PW605

PT604PW604

PT611PW611

PW607

PW609

PW602

PW609

PW630

NOTE: The PW613 Beveled Face Cap(shown) is Standard for Horizontal Members.The CW901 Square Face Cap is Optional.


P T 6 0 0

(Typ.)NP425

NP426(Typ.)

1

2

3

4

5

6

7

1 2

3

CP600Closure Plate




MID-SPAN ANCHORS AND MULLION SPLICE

12-J6

CURTAIN WALLS

J

J6


TYPICAL ELEVATION SECTION DETAIL

Splice

PT604PW604

MULLION LENGTH

MULLION

LENGTH

DIMENSION POINT

DIMENSION POINT

DIMENSION POINT

Splice

MULLION

LENGTH

FIXED ANCHOR(DEADLOAD ANCHOR)

Anchor CL

NOTE: Anchor Typeand Size varies perjob requirements.


P T 6 0 0

DIMENSION POINT

DIMENSION POINT

DIMENSION POINT

SERIES 4250TThermally BrokenInterior GlazedCurtain Wall

1

1

1

2

3

NOT TO SCALE




GB300

GB180

Floor

GypsumBoard(Drywall)

13-J6

CURTAIN WALLS

J6

Typical DetailsMID-SPAN ANCHORS AND MULLION SPLICE

J

ALUMINUM


P T 6 0 0

PT605PW605

MULLION LENGTH

MULLION LENGTH

DIMENSION POINT

Min. SpliceJoint

1/2"(12.7)

4" (101.6)

6" Sleeve (152.4)

Splice Joint WithSplice Sleeve

Steel Clip Angle WithVertically Slotted Hole

EXPANSION ANCHOR(WINDLOAD ANCHOR)

NOTE: Anchor Typeand Size varies per job requirements.

SPLICE JOINT

NOTE: Joint Width shouldbe based on Mullion Length and TemperatureDifferential. A 1/2" (12.7)gap allows for 1/4" (6.4)movement.

Anchor CLDIMENSION POINT

Min. Face Cap Splice

1/2"(12.7)

SERIES 4250TThermally BrokenInterior GlazedCurtain Wall

2

3

NOT TO SCALE




VERTICAL MULLIONS FOR 1" (25) GLAZING

14-J6

CURTAIN WALLS

J

J6

Windload ChartsALUMINUM

Aluminum alloy 6063-T5: allowable stress for windload 12,929 psi. (89 MPa)Steel reinforcing allowable stress for windload 26,666 psi. (183 MPa)

Curves represent the limit values and are based on criteria for simple beam, uniformly loaded,using the distribution of wind forces on the wall with rectangular loading. Glass is notconsidered as contributing to resistance of deflection.

Mullions designed for L/175 deflection ratio and for the following allowable working stresses:

Mullion Height in Feet (meters)


A

B

C

D

A

B

C

D

PW600 Vertical (shown)PT600I = 7.701 (320.54 x 104)S = 2.698 (44.21 x 103)

PW600 Vertical (shown)PT600 with SS964Steel StiffenerI = 1.996 (83.08 x 104)S = 1.141 (18.70 x 103)IAL+STL = 13.489 (561.45 x 104)

(1) (1.5) (2) (2.5)

18

17

16

15

14

13

12

11

10

9

(5)

(4.5)

(4)

(3.5)

(3)

2 3 4 5 6 7 8 9

20

19

18

17

16

15

14

13

12

11

(1) (1.5) (2) (2.5)

(6)

(5.5)

(5)

(4.5)

(4)

(3.5)

2 3 4 5 6 7 8 9

SERIES 4250TThermally Broken Interior Glazed Curtain Wall

Two digit Part Number prefixending in "T" representsTHERMALLY BROKEN parts.Thermal parts are in BOLD print.

P T 6 0 0

Mullion Spacing in Feet (meters)




Limitation of vertical mullions for:CURVES A = 15 PSF (718 Pa)CURVES B = 20 PSF (957 Pa)CURVES C = 25 PSF (1197 Pa)CURVES D = 30 PSF (1436 Pa)

15-J6

CURTAIN WALLS

J6

Windload Charts

J

ALUMINUM

VERTICAL MULLIONS FOR 1" (25) GLAZING


Aluminum alloy 6063-T5: allowable stress for windload 12,929 psi. (89 MPa)Steel reinforcing allowable stress for windload 26,666 psi. (183 MPa)

Curves represent the limit values and are based on criteria for simple beam, uniformly loaded,using the distribution of wind forces on the wall with rectangular loading. Glass is notconsidered as contributing to resistance of deflection.

Mullions designed for L/175 deflection ratio and for the following allowable working stresses:

A

B

C

D

A

B

C

D

PW610 Heavy Wall Vertical (shown)PT610I = 10.413 (433.42 x 104)S = 3.520 (57.68 x 103)

PW610 Heavy Wall Vertical (shown)PT610 With SS964Steel StiffenerI = 1.996 (83.08 x 104)S = 1.141 (18.70 x 103)IAL+STL = 16.201 (674.34 x 104)

(1) (1.5) (2) (2.5)

19

18

17

16

15

14

13

12

11

10

(5.5)

(5)

(4.5)

(4)

(3.5)

2 3 4 5 6 7 8 9

(1) (1.5) (2) (2.5)

21

20

19

18

17

16

15

14

13

12

(6)

(5.5)

(5)

(4.5)

(4)

2 3 4 5 6 7 8 9




P T 6 0 0





Limitation of vertical mullions for:CURVES A = 15 PSF (718 Pa)CURVES B = 20 PSF (957 Pa)CURVES C = 25 PSF (1197 Pa)CURVES D = 30 PSF (1436 Pa)

16-J6

CURTAIN WALLS

J

J6

Deadload ChartsALUMINUM



Deadload charts are based on 1/8" (3.2) maximum deflection at the center point of the horizontal member and on a glass weight of 3.25 psf (15.87 Kg/m2) for 1/4" (6) glass and 6.5 psf (31.74 Kg/m2) for 1" (25) glass.

Glass shall rest on two setting blocks located at:CURVES A: 1/4 pointsCURVES B: 1/8 points or 8" (203.2) from corners, whichever is larger

A

B

A B

FOR 1/4" (6) SPANDRAL GLAZING CONDITIONS

FOR 1" (25) GLAZING

PW605 Horizonal (shown)PT605Iyy = .484 (20.15 x 104)

PW604 Horizonal (shown)PT604Iyy = .476 (19.81 x 104)

(1) (1.5) (2) (2.5)

10

9

8

7

6

5

4

3

2

1

(3)

(2.5)

(2)

(1.5)

(1)

(0.5)

2 3 4 5 6 7 8 9

(1) (1.5) (2) (2.5)

10

9

8

7

6

5

4

3

2

1

(3)

(2.5)

(2)

(1.5)

(1)

(0.5)

2 3 4 5 6 7 8 9




P T 6 0 0




HORIZONTAL MULLIONS FOR 1" (25) GLAZINGAND 1/4" (6) SPANDRAL GLAZING

PART NO.

DETAIL DESCRIPTIONPKG.QTY.

AP670Wall Jamb Anchorat Head and Sill forPW600 and PT600

6

AP671Wall Jamb Anchorat Head and Sill forPW610 and PT610

6

AP660Intermediate VerticalAnchor at Head and Sill for PW600 and PT600

12

AP661Intermediate VerticalAnchor at Head and Sill for PW610 and PT610

12

SL400 Mullion Splice Sleevefor PW600 and PT600

12

SL408 Mullion Splice Sleevefor PW610 and PT610

12

SL690 Corner Splice Sleevefor PW630

5

NP425 Exterior Gasket300'Roll

NP606 Interior Gasket200'Roll

NP610

ExteriorReplacementGasket for

Spandrel Condition

300'Roll

NP620

InteriorReplacementGasket for

Spandrel Condition

300'Roll

PART NO.


AP603Shear Block for

PW604 and PW605(Includes Screws)

20

AP601

Shear Block for 90 DegreeOutside Corner

(Includes One Left Block, One Right Block,and Screws)

1Set

WD600End Dam

for Deep PocketPW600

50

WD601End Dam

for Shallow Pocket PW600

50

CP600 Closure Platefor Mullions

50

CP690 Closure Platefor Corner Mullion

10

SL404Splice Sleeve for Face of Vertical

12

SL403Splice Sleeve for Vertical Face Cap

12

ST197

Screw forSL404 Splice#8 x 3/8" (9.5)PHSMS

100

SS964Steel Stiffener

Fits in: PW610, PT610

16'(4.88 m)StockLength

PW616 Re-GlazingLeg Adapter

24'(7.3 m)StockLength

17-J6

CURTAIN WALLS

J6

Accessories

J


ALUMINUMThermally Broken

• Series 4250T


FOR 1/4" (6) AND 1" (25) GLAZING

18-J6

CURTAIN WALLS

J

J6

AccessoriesALUMINUM

PART NO.


SB650Setting Block

for 1" (25) Glass;4" (101.6) Long

100

SB655Setting Block

for 1/4" (6) Glass;4" (101.6) Long

100

WB600Edge Block forDeep Pocket8" (203.2) Long

50

WB601Edge Block forShallow Pocket6" (152.4) Long

50

UB600 Weep Baffle4" (101.6) Long

100




PART NO.


WD602

Water Dam forThermal Regletof Non-thermal

Verticals

50

BA603

Plug Backer forPW614 Deep PocketSpandrel AdaptorUse With PW615

100

BA602

Plug Backer forPW615 ShallowPocket SpandrelAdaptor Use With

PW614

50

DJ620Drill Jig

for Horizontal Mullions

1

DJ610Drill Jig

for Vertical Mullions

1

Project: Cancer Center, Fort Worth, TX

FOR 1/4" (6) AND 1" (25) GLAZING

curtain walls aluminum - crl-arch · curtain walls j j6 technical data aluminum series width depth...

Documents