cts/titan injection bore system - con-tech · pdf filects/titaninjection bore system tie back...
TRANSCRIPT
CTS/TITAN Injection Bore System
Tie Back Anchors
Soil Nails &
Micropiles
G IBO®: Injection BOring
G Dynamic pressure grouted,
casing free single step
installation
G Suits all ground conditions
G Rapid, effective ground
and structural stabilisation
November 2006CON-TECH SYSTEMS LTD HQ: 8150 RIVER ROAD • DELTA BC, V4G 1B5 • CANADA • PH: (604) 946-5571 • FAX: (604) 946-5548
WESTERN DIVISION: DELTA, BC, PH: (604) 946-5571, FAX: (604) 946-5548 • DESCANSO CA, USA, PH: (619) 659-9931
FAX: (619)659-9932, E-MAIL: [email protected]
EASTERN DIVISION: • ELIZABETHTOWN ON • CANADA • PH: (613) 342-0041, FAX: (613) 342-0609 • RICHEY FL, USA,
PH: (866) 848 6800 • CHARLOTTE NC, USA, (704) 494-3989 • E-MAIL: [email protected]
CTSCON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
2
1 Technical Data 3
2 Drill Bit Selection Chart 5
3 R32/20 7
4 TITAN 30/11, TITAN 30/14 & TITAN 30/16 9
5 TITAN 40/16 & TITAN40/20 13
6 TITAN 52/26 17
7 TITAN 73/56, TITAN 73/53TITAN 73/45 & TITAN 73/35 19
8 TITAN 103/78 & TITAN103/51 21
9 TITAN 130/60 23
Disclaimer:
All products are subject to change at any time without notice. Con-Tech Systems will make the best effort to keep
you informed about any changes. Please check our website (www.contechsystems.com) for updates.
All photos are for illustrative purpose only; weights are approximate.
Products must be used in conformity with safe practices and applicable codes.
For best performance results, refere to CTS/TITAN/IBO installation procedures
Parts-List Index
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
CTS/TITAN Technical Data
3
CTS
Rod
Siz
eW
eigh
tD
Ø /
INN
ER
ØU
ltim
ate
Yie
ldM
ax. T
est
Des
ign1
Des
ign2
Effe
ctiv
eN
omin
alG
.U.T
.S.
Tem
p. A
nch.
60%
G.U
.T.S
.d
ØD
Øm
min
2ki
pski
pski
pski
pski
psin
inlb
s./lf
.m
m2
kNkN
kNkN
kNm
mm
mkg
/m30
/16
0.59
49.5
40.5
39.6
34.6
29.7
1.02
1.18
1.8
L.H
. TH
RE
AD
382
220
180
176
154
132
2630
2.7
30/1
40.
6158
.549
.546
.840
.935
.11.
031.
181.
9L.
H. T
HR
EA
D39
526
022
020
8.0
182
156
2630
2.9
32/2
00.
6065
.454
.952
.345
.839
.31.
101.
262.
2L.
H. T
HR
EA
D38
929
124
423
320
417
528
323.
230
/11
0.69
72.0
58.5
5850
.443
.21.
031.
182.
2L.
H. T
HR
EA
D44
632
026
025
622
419
226
303.
340
/20
1.13
121.
296
.795
.684
.872
.71.
421.
573.
8L.
H. T
HR
EA
D72
653
943
042
537
732
336
405.
640
/16
1.36
148.
411
8.1
116.
910
3.9
89.0
1.42
1.57
4.7
L.H
. TH
RE
AD
879
660
525
520
462
396
3640
7.0
52/2
62.
0720
8.9
164.
216
0.1
146.
212
5.3
1.92
2.05
6.7
L.H
. TH
RE
AD
1337
929
730
712
650
557
4952
10.0
73/5
62.
1926
8.5
176.
517
4.3
173.
216
1.1
2.76
2.87
7.5
R.H
. TH
RE
AD
1414
1194
785
775
770
716
7073
11.1
73/5
32.
5326
0.9
218.
120
8.7
182.
615
6.5
2.76
2.87
8.3
R.H
. TH
RE
AD
1631
1160
970
928
812
696
7073
12.3
73/4
53.
5036
6.5
265.
326
3.1
256.
621
9.9
2.76
2.87
12.0
R.H
. TH
RE
AD
2260
1630
1180
1170
1141
978
7073
17.8
73/3
54.
2044
5.2
304.
730
2.5
301.
326
7.1
2.76
2.87
14.2
R.H
. TH
RE
AD
2710
1980
1355
1345
1340
1188
7073
21.2
103/
784.
8851
3.2
404.
840
0.3
359.
230
7.9
3.94
4.06
16.7
R.H
. TH
RE
AD
3146
2282
1800
1780
1597
1369
100
103
24.9
103/
518.
5377
8.1
618.
461
6.1
544.
646
6.8
3.94
4.06
29.2
R.H
. TH
RE
AD
5501
3460
2750
2740
2422
2076
100
103
43.4
127/
111*
4.65
539.
740
7.0
404.
837
7.8
323.
83.
944.
0615
.8R
.H. T
HR
EA
D30
0024
0018
1018
0016
8014
4010
010
323
.513
0/60
14.7
917
85.5
1180
.611
73.8
1169
.310
71.3
4.92
5.12
50.4
R.H
. TH
RE
AD
9540
7940
5250
5220
5200
4764
125
130
75.0
1 Tem
pora
ry A
ncho
rs ;
2 Per
man
ent A
ncho
rsIm
peria
l val
ues
conv
erte
d fro
m m
etric
val
ues;
Oct
ober
200
6
Are
aLo
ad C
apac
ityO
utsi
de D
iam
eter
November 2006
TIT
AN
127/1
11:
Allo
wable
ben-
din
g m
om
ent
=
23.9
kN
m
(737.5
lbsft)
Cert
ifie
d t
o
ISO
9001
No
te:
Subje
ct
to
change w
ithout
notice.
Sh
ear
Fo
rce
Allo
wable
shear
forc
e is d
ete
r-
min
ed b
y t
he
form
ula
:
Qa
llow
=Y
ield
*A
1.7
5*√3
A:
(Ste
el) A
rea
November 2006
CTSCON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
CTS/TITAN Technical Data
4
THE TITAN THREAD MEETS AND EXCEEDS ASTM REQUIREMENTS
FOR RE-BAR DEFORMATIONS (ASTM-A-615). GROUT CRACK
WIDTH = O.1mm AT 1.25 OF DESIGN LOAD.
NO ADDITIONAL CORROSION PROTECTION IS REQUIRED
IBO/TITAN BARS ARE ROLLED OUT OF HIGH QUALITY STEEL TUB-
ING FOR SOIL NAILS, ROCK AND SOIL ANCHORS AND MINI /
MICRO PILES.
THEIR UNIQUE INSTALLATION METHOD, I.E. DYNAMIC (TREMI)-
GROUTING DURING DRILLING ASSURES CONTINUOUS GROUT
COVER FOR GOOD CORROSION PROTECTION AND SUPERIOR
SKIN FRICTION AND BOND.
FOR ADDITIONAL CORROSION PROTECTION, BARS AND HARD-
WARE CAN ALSO BE
EPOXY COATED, acc. to ASTM A-934, ASTM A-775 or AASHTO M284
ZINC METALLIZED, acc. to ASTM A-153 or AASHTO M232
HOT DIP GALVANIZED, acc. to ASTM A-153 or AASHTO M232
OR BE SUPPLIED IN (INOX) STAINLESS STEEL.
INSTEAD OF EXTRA CORROSION PROTECTION, THE SACRIFICIAL-
STEEL METHOD, CHOOSING THE BAR LARGER THAN
REQUIRED, CAN BE USED. THIS METHOD IS VERY COMMON IN
EUROPE AND FOR REINFORCED EARTH SYSTEMS.
STOCKED TITAN BARS: 30/16, R32/20, 30/11, 30/14, 40/20, 40/16,
52/26, 73/53, 103/78, 103/51.
NOTES:
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
Drill Bit Selection Chart
5
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
Carb
ide C
ross
Carb
ide C
ross
Cut 3
-ste
pC
ut 3
-ste
p
carb
ide ti
pped
carb
ide ti
pped
ha
rdn
ess H
V 1
80
0 h
ard
ne
ss H
V 1
80
0
(75
mm
Ø)
90
mm
Ø
Button T
ype
Button T
ype
hard
ness H
V 7
00
hard
ness H
V 7
00
42
mm
Ø / 4
6 m
m Ø
/ 5
1 m
m Ø
/ 5
5 m
m Ø
70
mm
Ø
Mic
ro
Pil
es
DIN
41
28
/ S
oil
Na
ils
/ A
nc
ho
rs
DIN
41
25
TITAN
TITAN
TITAN
TITAN
TITAN
TITAN
30/1
1(left)
40/1
6(left)
52/2
673/5
3(r
ight)
1
03/7
8(r
ight)
103/5
1(r
igh
t)
Cro
ss C
ut
Cro
ss C
ut
Cro
ss C
ut
Cro
ss C
ut
Cro
ss C
ut
Cro
ss C
ut
Drill
Bit
Drill
Bit
Drill
Bit
Drill
Bit
Drill
Bit
Drill
Bit
hard
ness H
V 3
75
hard
ness H
V 3
75 h
ard
ness H
V 3
75
hard
ness H
V 3
75
hard
ness H
V 3
75
hard
ness H
V 3
75
90
mm
Ø9
0 m
m Ø
11
5 m
m Ø
13
0 m
m Ø
17
5 m
m Ø
17
5 m
m Ø
11
5 m
m Ø
13
0 m
m Ø
17
5 m
m Ø
for
cla
y, so
ft s
oil
and s
and/g
ravel
< 5
0 S
.P.T
.
Cla
y B
itC
lay B
itC
lay B
itC
lay B
itC
lay B
itC
lay B
it
hard
ness H
V 2
70 h
ard
ness H
V 2
70 h
ard
ness H
V 2
70
hard
ness H
V 2
70
hard
ness H
V 2
70
hard
ness H
V 2
70
75
mm
Ø1
10
mm
Ø1
30
mm
Ø 2
00
mm
Ø 2
80
mm
Ø 2
80
mm
Ø
95
mm
Ø1
50
mm
Ø
for hard
or hig
h q
uarz
ite rock,
rein
forc
ed c
oncre
te B
25 a
t the
begin
nin
g
> 7
0 M
Pa
Button T
ype
Button T
ype
Button T
ype
Button T
ype
Button T
ype
carb
ide ti
pped
carb
ide ti
pped
carb
ide ti
pped
carb
ide ti
pped
carb
ide ti
pped
ha
rdn
ess H
V 1
80
0hard
ness H
V1800
hard
ne
ss H
V 1
80
0h
ard
ne
ss H
V 1
80
0h
ard
ne
ss H
V 1
80
0
90
mm
Ø1
15
mm
Ø1
30
mm
Ø1
75
mm
Ø1
75
mm
Ø
for directional s
tabili
ty o
f
+ 2
% o
f th
e to
tal le
ng
th
TITAN
30/1
1(left)
TITAN
40
/16
(le
ft)
expla
nation to
diffe
rent
- H
ard
ness to M
ohs e
.g.d
iam
ant 10, carb
ide 9
,5, corr
espond to H
V 1
800 (
Hard
ness to V
ickers
),quarz
ite 7
, sla
te 2
,5
decla
rations o
f hard
ness
- H
RC
60 (H
ard
ness to R
ockw
ell
C) corr
espond to H
V 7
00 (H
ard
ness to V
ickers
), H
RC
38 c
orr
espond to H
V 3
75
and rock h
ard
ness:
- 70 M
Pa (soft s
oil
and lo
ose s
and/g
ravel)
- 7
0 ÷
150 M
Pa (fo
r hard
rock, lik
e d
olo
mit, gra
nite, sandsto
ne)
- S
.P.T
. valu
e (S
tandard
Penetr
ation T
est)
for m
ixed s
oil
with o
bsta
cle
s
> 5
0 S
.P.T
.
Carb
ide O
ffset C
ross C
ut
Carb
ide O
ffset C
ross C
ut
hard
ness H
V 1
800
hard
ness H
V 1
800
46
mm
Ø7
0 m
m Ø
AV
8/B
1-6
for w
ea
the
red
so
ft ro
ck
and g
ravel
hard
ness <
70 M
Pa
for h
ard
ro
ck,
gra
nite, d
olo
mite, s
tandsto
ne,
hard
ness 7
0 - 1
50 M
Pa
Page left blank intentionally
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
CTS/TITAN
6
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
7
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN R32/20
CTS Injection Bore Hollow Bar System R32/20
TITAN Injection Hollow Bar, 32/20 mm, design load (60% GUTS) 175 kN,
left hand threaded in lengths of 3 m black
part.no. R32-0127 3.20 kg/m pc
Accessories
Spherical Collar Nut
black, part.no. R32-0126 0.35 kg pc. stock
Coupling
black, part.no. R32-0124 0.43 kg pc. stock
CTS Drill Bit - Carbide 2”, (51mm Ø),
carbide tipped, part.no. R32-0117 0.37 kg pc. stock
CTS Drill Bit - Carbide 2.5”, (63.5mm Ø),
carbide tipped, part.no. R32-0119 0.37 kg pc. stock
TITAN Drill Bit - Soil Bit Y-Cut 3”, (76 mm Ø),
part.no. R32-0115 0.69 kg pc. stock
TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel,
induction hardened part.no. R32-0116 0.44 kg pc. stock
Flushing Head 32/20 available for R 32* (1 -1/4"), R 38* (1 -1/2"), T 38*, T 45*,
for left hand rotary/percussion drilling, for flushing with water, grout or air,
thread Rd 32 x 1/8" (BSP 3/4”) male for grout hose, with lubrication nipple, to be
used in connection with holder only, incl. transport box,
length 265 mm, part.no. P32-001/.002/R32-0113/P32-003 14.00 kg pc. st. T38
complete set of spare seals for R 32 - T 45 flushing heads
(2 seals 63 x 78 x 11.4 mm plus 2 guide rings 63 x 68 x 6.3 mm)
part.no. T30-0369 set stock
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,
to be fixed on to the mast of the drill rig, fixing position:
hammer fully extended and spring released
part.no. T30-0370 5.90 kg pc. stock
CTS Grout Swivel - T38m/T38m
for left hand rotary/percussion drilling and for flushing with water, grout or air
1” NPT male for grout hose connection
part.no. TAC-003 6.75 kg pc. stock
CTS Adaptor Couplers - T38/R32
part.no. MIC-0032 3.2 kg pc. stock
* please specify when ordering
Drill Connectors or flushing heads for other drill threads on request
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
8
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
Page left blank intentionally
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
9
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 30/16 & 30/11
CTS/TITAN Injection Bore Hollow Bar System 30 / 16
TITAN Injection Hollow Bar, 30/16 mm, design load (60% GUTS) 132 kN.
left hand threaded, suitable for all 30/11 accessories,
in 3m lengths.
black part.no. T30-0341 2.87 kg/m pc. stock
CTS/TITAN Injection Bore Hollow Bar System 30 / 14
TITAN Injection Hollow Bar, 30/14 mm, design load (60% GUTS) 156 kN,
left hand threaded,
in 3m lengths
black part.no. T30-0004 3.29 kg/m pc. stock
CTS/TITAN Injection Bore Hollow Bar System 30 / 11
TITAN Injection Hollow Bar, 30/11 mm, design load (60% GUTS) 192 kN,
left hand threaded,
in 3m lengths
black part.no. T30-0351 3.42 kg/m pc. stock
INOX, stainless steel, material no. 1.4462, with approval Z-30.3-6
in 3 m lengths. part.no. T30-0373 3.42 kg/m pc. stock
CTS/TITAN 30/16 and 30/11 Injection Anchors are also available in other
lengths. Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors
and Accessories are also available. Please ask us for pricing.
Accessories
Spherical Collar Nut SW 46 x 35 mm. inclination ± 7.5
black, part.no. T30-0362 0.34 kg pc. stock
INOX Sperical Collar Nut, stainless steel,
material no. 1.4468, part.no. T30-0358 0.42 kg pc. stock
Coupling 38 Ø x 105 mm. with center-stop.
black, part.no. T30-0355 0.42 kg pc. stock
INOX Coupling, stainless steel,
material no. 1.4468, part.no. T30-0357 0.40 kg pc. stock
Bearing Plate, 200 x 200 x 8 mm, for shotcrete,
black, part.no. T30-0372 2.43 kg pc. stock
Bearing Plate INOX, 200 x 200 x 12 mm, stainless steel,
hole Ø 38 mm,
material no. 1.4301 part.no. T30-0359 3.85 kg pc. stock
Steel ball 80 mm Ø, hole Ø 32 mm, max. inclination ± 36°,
black part.no. P30-001 1.87 kg pc.
Plate for Steel Ball, 300 x 200 x 23 mm (without steel ball)
to be used on four double U-300 walers, spaced max. 150 mm
black part.no. PAC-002 13.00 kg pc.
Geotextile Fixing Plate, 285 mm Ø for CTS/TITAN 30/11 and 40/16
galv. part.no. P30-003 6.00 kg pc.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
CTS/TITAN 30/16 & 30/11
10
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
Accessories
Wedge Disc 30/11, 12°, allows 3 x 12° angle,
black, weldable part.no. T30-0361 0.91 kg pc.
Adaptor for Injection Hollow Bar 30/11 on drill bit 40/16
part.no. T30-0334 0.21 kg pc.
Drill Bits
TITAN Drill Bit - Button Type 42, (42 mm Ø), hardness HRC 54,
for hand-held rotary percussion drills, for soft rock and concrete
part.no. P30-004 0.28 kg pc.
TITAN Drill Bit - Button Type 46, (46 mm Ø), hardness HRC 54,
with top and radial flushing holes, suitable for airtrack drilling machines
for harder rock and concrete
part.no. T30-0344 0.32 kg pc. stock
TITAN Drill Bit - Button Type 51, (51 mm Ø), hardness HRC 54,
with top and radial flushing holes, suitable for airtrack drilling machines
for harder rock and concrete.
part.no. P30-005 0.34 kg pc.
TITAN Drill Bit - Button Type 55, (55 mm Ø),
for weathered soft rock and gravel
part.no. T30-0345 0.38 kg pc. stock
TITAN Drill Bit - Carbide Offset Cross Cut 46, (46 mm Ø)
carbide tipped, part.no. T30-0346 0.37 kg pc. stock
CTS/TITAN Drill Bit - Carbide 2” (51 mm)
carbide tipped, part.no. T30-0349 0.63 kg pc. stock
CTS/TITAN Drill Bit - Carbide 2.5” (63 mm)
carbide tipped, part.no. T30-0350 1.46 kg pc. stock
CTS/TITAN Drill Bit - Carbide 3” (76 mm)
carbide tipped, part.no. T30-0375 1.7 kg pc. stock
TITAN Drill Bit - Carbide Cross Cut 2-Step 75, (75 mm Ø)
drill bit for directional stability, cuts through several hard layers of soil/rock
part.no. T30-0347 0.84 kg pc.
TITAN Drill Bit - 3 Cut 76, (76 mm Ø)
with recess center buttons hardened to 57 Rc
part.no. P30-006 0.69 kg pc.
TITAN Drill Bit - Cross Cut 90 mixed Ground, (90 mm Ø)
part.no. T30-0007 1.27 kg pc. stock
TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel.
induction hardened part.no. T30-0348 0.44 kg pc. stock
TITAN Drill Bit - Clay bit 95 mm Ø for soft soil and loose sand/gravel.
induction hardened part.no. T30-0003 0.55 kg pc. stock
Piling Cone 75, (75 mm Ø), with backwards pointing injection hole
part.no. T30-0364 0.68 kg pc.
Centralizer TITAN 30, 70 mm Ø, for 20 mm grout cover, cast iron
black part.no. T30-0335 0.23 kg pc. stock
Centralizer TITAN 30, 88 mm Ø, cast iron
to seal bore holes of 33 mm up to 56 mm Ø
black part.no. P30-007 0.27 kg pc.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
11Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 30/16 & 30/11CTS
Accessories
Bore Hole Stopper screws on to the anchor, material PE,
to seal bore holes of 33 mm up to 56 mm Ø
part.no. T30-0365 0.10 kg pc.
Eye bolt, 35 mm eye diam., SWL 30 kN
galvanized part.no. P30-008 0.50 kg pc.
Eyebolt, inside Ø, 40/30 mm, for shackles max. M 30,
SWL 150 kN
galvanized part.no. T30-0010 1.90 kg pc. stock
Load Indicator for 30/11, to indicate loads of 70, 160 and 180 kN,
retracts by a total of 30 mm, LOBA approved
galvanized part.no. T30-0367 0.42 kg pc. stock
Expansion Shell for 30/11 and 30/16 anchors for drill hole Ø 46 up to 56 mm
part.no. T30-0368 0.77 kg pc.
Self contained Flushing Head S 22 for 30/11, for left-hand hand-held hammers
(no holder required) part.no. T30-0386 5.96 kg pc. stock
Flushing Head 30/11, for hexagon S 22 (7/8"), for left hand rotary/percussive
drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for
grout hose, length 323 mm, to be used in connection with holder only
incl. transport box part.no. T30-0336 5.40 kg pc.
Complete set of spare seals for S 22 flushing head (2 pieces, 40 x 50 x 7 mm)
part.no. TAC-0018 set
Holder, spring action, for flushing head 30/11-S 22,
bolts on to the mast of the drill rig
part.no. TAC-0019 7.28 kg pc.
Flushing Head 30/11 available for R 32* (1-¼"), R 38* (1 -1/2"), T 38*, T 45*,
for left hand rotary and percussive drilling, for flushing with water, grout or air, thread
Rd 32 x 1/8" (BSP 3/4") male for grout hose, with lubrication nipple, to be used in
connection with holder only, incl. transport box,
length 265 mm, part.no. T30-0339/..0380/..0340/..0379/ 14.00 kg pc. stock
complete set of spare seals for R 32 - T 45 flushing heads
(2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6,3 mm)
part.no. TAC-0005 set stock
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,to be fixed on to the mast of the drill rig, fixing position: hammer fully extended and
spring released
part.no. T3AC-0020 5.90 kg pc. stock
*please specify when ordering
Drill Connectors or flushing heads for other drill threads on request
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
12
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 30/16 & 30/11
Grouting Connector for 30/11thread Rd 32 x 1/8" male, for high pressure grout-hose DN 20, with handle and
lubrication nipple
zinc plated part.no. T30-0333 0.92 kg pc.
CTS Grout Swivel - T38m/T38mfor left hand rotary/percussion drilling and for flushing with water, grout or air
1” NPT male for grout hose connection
part.no. TAC-0003 6.75 kg pc. stock
CTS Adaptor Couplers - T38/TITAN30
part.no. MIC-0035 2.27 kg pc. stock
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
13
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 40/16 & 40/20
CTS/TITAN Injection Bore Hollow Bar System 40 / 16
TITAN Injection Hollow Bar, 40/16 mm, design load (60% GUTS) 396 kN,
continuously left hand threaded,
in lengths of 3 m.
black part.no. T40-0247 7.00 kg/m pc. stock
INOX, stainless steel, material no. 1.4462,
in 3 m lengths part.no. T40-0299 7.00 kg/m pc. stock
CTS/TITAN Injection Bore Hollow Bar System 40 / 20
TITAN Injection Hollow Bar, 40/20 mm, design load (60% GUTS) 323 kN,
in lengths of 3 m
black part.no. T42-0002 5.60 kg/m pc. stock
CTS/TITAN 40/16 and 40/20 are also available in other lengths.
Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated Injection Anchors and
Accessories are also available. Please ask us for pricing.
Accessories
Spherical Collar Nut SW 65 x 50 mm, inclination ± 7°.
black, part.no. T40-0263 0.87 kg pc. stock
INOX Sperical Collar Nut, stainless steel, material no. 1.4468
part.no. T40-0261 0.88 kg pc. stock
Coupling, 54 mm Ø x 140 mm, with center-stop, hardened, with 2 rubber seals
black part.no. T40-0259 1.12 kg pc. stock
INOX Coupling, stainless steel,
material no. 1.4468 part.no. T40-0260 1.13 kg pc. stock
Bayonet Coupler 63 Ø x 228 mm, recoverable
part.no. T40-0291 1.40 kg pc. stock
Bearing Plate, 200 x 200 x 12 mm, hole Ø 56 mm,
black part.no. T40-0270 3.50 kg pc. stock
Bearing Plate, 200 x 200 x 30 mm, hole Ø 56 mm, for anchorpiles,
black part.no. P40-001 8.50 kg pc.
INOX Bearing Plate, 200 x 200 x 15 mm, hole Ø 54 mm,
stainless steel,
material no. 1.4301 part.no. T40-0300 4.58 kg pc.
Steel ball 80 mm Ø, hole Ø 42 mm, max. inclination ± 36°,
black part.no. P40-002 1.59 kg pc.
Plate for Steel Ball, 300 x 200 x 23 mm (without steel ball)
to be used on four double U-300 walers, spaced max. 150 mm
black part.no. PAC-001 13.00 kg pc.
Wedge Disc 40/16, 12°, weldable
black part.no. T40-0262 1.43 kg pc. stock
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
14
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 40/16 & 40/20
Accessories
TITAN Drill Bit - Clay bit 110 mm Ø for soft soil and loose sand/gravel,
induction hardened
part. no. T40-0255 1.28 kg pc. stock
TITAN Drill Bit - HPI-Clay bit 110 mm Ø for jet grouting up to 200 bars,
with 2 nozzles, 2,3 mm Ø,
part.no. T40-0254 1.34 kg pc. stock
TITAN Drill Bit - Clay bit 150 mm Ø
induction hardened
part.no. T40-0297 1.5 kg pc. stock
TITAN Drill Bit - Button Type 70, (70 mm Ø ), for soft rock and gravel,
hardness HRC 54, with top and radial flushing holes,
screw-on type.
part.no. T40-0250 0.68 kg pc. stock
TITAN Drill Bit - Carbide button drill bit 90, (90 mm Ø ),
screw-on type.
part.no. P40-003 1.27 kg pc.
TITAN Drill Bit - Carbide Cross Cut 70, (70 mm Ø), for hard rock,
screw-on type
part.no. T40-0252 0.98 kg pc. stock
CTS/TITAN Drill Bit - Carbide 3” (76 mm)
carbide tipped,
part.no. T40-0257 1.75 kg pc. stock
CTS/TITAN Drill Bit - Carbide 3.5” (89 mm)
carbide tipped,
part.no. T40-0276 2.38 kg pc. stock
TITAN Drill Bit - Cross Cut 90, (90 mm Ø), mixed soil with obstacles
part.no. T40-0256 1.05 kg pc. stock
TITAN Drill Bit - Cross Cut 115 (115 mm Ø), for soft soils, sand and cobbles and
soft rock, with top and radial flushingholes,
screw-on type
part.no. T40-0296 2 kg pc. stock
TITAN Drill Bit - Aggressive Soft Soil Bit, 100 mm Ø, for clay and mudstone,
screw-on type
part.no. T40-0253 0.83 kg pc.
TITAN Drill Bit - Carbide cross cut 3-step, cuts through several hard layers,
screw-on type
part.no. P40-004 1.2 kg pc.
Piling Cone, (90 mm Ø), for displaceable soils, clay or high water table,
screw-on type
part.no. T40-0264 2.06 kg pc.
Centralizer 88 mm Ø, for 20 mm grout cover,
cast iron
black part.no. T40-0242 0.45 kg pc. stock
Geotextile Fixing Plate, 285 mm Ø for CTS/TITAN 30/11 and 40/16
galv. part.no. P30-005 6.00 kg pc.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
15
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 40/16 & 40/20
Accessories
Bore Hole Stopper, material PE, to seal bore holes, up to 80 mm Ø,
screw-on type, 100 mm long,
part.no. P40-010 0.1 kg pc.
Eye bolt, hole 40/30 mm, SWL 300 kN
galvanized part.no. T40-0303 1.90 kg pc.
Load Indicator for 40/16, to indicate loads of 200, 300 and 400 kN, retracts by a
total of 40 mm, LOBA approved
galvanized part.no. P40-012 0.59 kg pc.
Flushing Head 40/16 for hexagon S 22 (7/8"), for left hand rotary and percussive
drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for
grout hose, length 368 mm, to be used in connection with holder only, incl. transport
box,
part.no. P40-013 6.40 kg pc.
Complete set of spare seals for S 22 flushing heads
(2 pieces, 40 x 50 x 7 mm)
part.no. TAC-0018 set
Holder, spring action, for Flushing Head 40/16-S22,
bolts on to the mast of the drill rig,
part.no. TAC-0019 7.20 kg pc.
Flushing Head 40/16 available for R32*(1-1/4"), R38*(1-1/2"), T38*, T45* ,
for left hand rotary and percussive drilling, for flushing with water, grout or air, thread
Rd 32 x 1/8 " (BSP 3/4") male for grout hose, with lubrication nipple, length 265 mm,
to be used in connection with holder only, incl. transport box,
part.no. T40-0279/..0244/..0243/..024513.30 kg pc. stock
Complete set of spare seals for R 32 - T 45 flushing heads
(2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6.3 mm)
part.no. TAC-0005 set stock
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,
to be fixed on to the mast of the drill rig
fixing position: hammer fully extended and spring released
part.no. TAC-0020 5.90 kg pc. stock
Flushing Head R 55 (2-1/4"), for left hand rotary and percussive drilling, for flush-
ing with water, grout or air, thread Rd 32 x 1/8" (BSP R 3/4") male for grout hose,
with lubrication nipple, length 365 mm, to be used in connection with holder only,
incl. transport box
part.no. T40-0295 34.20 kg pc.
Complete set of spare seals for R 55 flushing heads
( 2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm)
part.no. TAC-0021 set
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc.
*please specify when ordering
Drill Connectors or flushing heads for other threads on request.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
16
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 40/16 & 40/20
Grouting Connector, for high pressure grout-hose DN 20
thread Rd32 x 1/8” male, with handle and lubrication nipple
galvanized part no. T40-0241 1.5 kg pc.
CTS Grout Swivel - T38m/T38mfor left hand rotary/percussion drilling and for flushing with water, grout or air
1” NPT male for grout hose connection
part.no. TAC-0003 6.75 kg pc. stock
CTS Adaptor Couplers - T38/TITAN40
part.no. MIC-0034 2.95 kg pc. stock
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
17
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 52/26
CTS/TITAN Injection Bore Hollow Bar System 52/26
CTS/TITAN Injection Hollow Bar 52/26, design load (60% GUTS) 557 kN, left handthreaded, right-hand threaded available on special order
in 3 m lengths.
black left hand thread part.no. T52-0160 9.83 kg/m pc. stock
Accessories
Spherical Collar Nut SW 80 x 70,
max. inclination ± 10° of washer plate,
black part.no. T52-0162 2.20 kg pc. stock
Coupling 70 mm Ø x 160 mm, with center-stop, hardened, with 2 rubber seals,
black part.no. T52-0161 2.42 kg pc. stock
Bayonet Coupler 105 Ø x 325 mm, recoverable
part.no. P52-006 11.70 kg pc.
Adapter for Bayonet Coupler, recoverable
part.no. P52-007
Bearing Plate, 220 x 220 x 35 mm for Anchorpiles,
hole Ø 65 mm
black part.no. T52-0157 13.1 kg pc.
Steel Ball, 100 mm Ø, black,
54 mm bore in the steel ball, max. inclination 36°
part.no. P52-001 3.25 kg pc.
Plate for Steel Ball 300 x 200 x 35 mm, hole Ø 93
without ball, black part.no. P52-001a 14.4 kg pc.
Wedge Disc, 12°, allows max. 0 x 24°, black,
part.no. T52-0152 5.00 kg pc. stock
Drill Bits
TITAN Drill Bit - Cross Cut 115, (115 mm Ø), for soft soils, sand and cobbles and
soft rock with top and radial flushing holes,
screw-on type part.no. T52-0147 2.51 kg pc. stock
CTS/TITAN Drill Bit - Carbide 3.5” (89 mm)
carbide tipped part.no. T52-0150 2.04 kg pc. stock
TITAN Drill Bit - Clay bit 130 mm Ø,
screw-on type part.no. T52-0165 2.37 kg pc. stock
TITAN Drill Bit - HPI-Clay bit 130 mm Ø, for jet grouting up to 200 bar
with 2 nozzles, 2,3 mm Ø,
part.no. P52-003 2.40 kg pc. stock
TITAN Drill Bit - Button Type 115, (115 mm Ø), for hard or high quarzite rock car-
bide tipped
screw-on type
part.no. P52-004 3.3 kg pc.
CTS/TITAN 52/26 Injection Anchors are also available in other lengths.
Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors
and Accessories are also available. Please ask us for pricing.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
18
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 52/26
Accessories
Centralizer 112 mm Ø, cast iron
black part.no. T52-0140 1.2 kg pc. stock
Flushing Head 52/26 available for R32*(1-1/4"), R38*(1-1/2"), T38*, T45*,for rotary/percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8"
(BSP 3/4") male for grout hose, with lubrication nipple, length 365 mm, to be used in
connection with holder only, incl. transport box,
part.no. T52-0172/..0142/..0164/..0158/ 18.80 kg pc. stock
complete set of spare seals for flushing heads R 32 - T 45(2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6,3 mm)
part.no. TAC-0005 set stock
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,to be fixed on to the mast of the drill rig
fixing position: hammer fully extended and spring released
part.no. TAC-0020 5.90 kg pc. stock
Flushing Head R 55 ( 2- 1/4"), for rotary/percussive drilling, for flushing with water,
grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female for grout hose, with
lubrication nipple, length 365 mm, to be used in connection with holder only, incl.
transport box
part.no. T5R-0050 34.30 kg pc.
complete set of spare seals for R 55 flushing head
(2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9,7 mm)
part.no. TAC-0021 set
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc. stock
Grouting Connector for 52/26 , for high pressure grout-hose DN 20, thread Rd 32
x 1/8" male, with handle and lubrication nipple, galvanized
part.no. P52-005 1.80 kg pc.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
19
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 73/56, 73/53 & 73/45
CTS/TITAN Injection Bore Hollow Bar System 73 / 56
CTS/TITAN Injection Hollow Bar 73/56, design load (60% GUTS) 656 kN
continuously right-hand threaded
in 6.25 m lengths
black, part.no. T73-0172 10.75 kg/m pc. stock
CTS/TITAN Injection Bore Hollow Bar System 73 / 53
CTS/TITAN Injection Hollow Bar 73/53, design load (60% GUTS) 696 kN
continuously right-hand threaded
in 3 m lengths
black, part.no. T73-0154 12.24 kg/m pc. stock
CTS/TITAN Injection Bore Hollow Bar System 73 / 45
CTS/TITAN Injection Hollow Bar 73/45, design load (60% GUTS) 978 kN
continuously right-hand threaded
in 3 m lengths
black, part.no. T73-0173 17.8 kg/m pc. stock
CTS/TITAN Injection Bore Hollow Bar System 73 / 35
CTS/TITAN Injection Hollow Bar 73/35, design load (60% GUTS) 1188 kN
continuously right-hand threaded
in 3 m lengths
black, part.no. T73-0173 17.8 kg/m pc. stock
Accessories
Spherical Collar Nut SW 95 x 70
black, part.no. T73-0163 2.22 kg pc. stock
Coupling 89 Ø x 225 mm,
St. 52-3, with internal rubber seal,
black, part.no. T73-0161 3.72 kg pc. stock
Bayonet Coupler 105 Ø x 325 mm, recoverable
part.no. P73-001 11.70 kg pc.
Bearing Plate, 250 x 250 x 40 mm for Anchorpiles,
hole Ø 80 mm, max. inclination ± 6°,
black part.no. T73-0166 18.00 kg pc.
Wedge Disc, 12° for 73/53, 200 mm, allows max. 2 x 12°,
black, part.no. T73-0162 5.97 kg pc. stock
Centralizer 130 mm Ø, cast iron,
black part.no. T73-0148 1.39 kg pc. stock
CTS/TITAN 73 Injection Anchors are also available in other lengths.
Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors
and Accessories are also available. Please ask us for pricing.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
20
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 73/56, 73/53 & 73/45
Accessories
TITAN Drill Bit - Cross Cut, 130 mm Ø, for mixed soil with obstacles,
screw-on type
part.no. T73-0157 3.12 kg pc. stock
TITAN Drill Bit - Cross Cut, 175 mm Øscrew-on type
part.no. T73-0169 8.22 kg pc. stock
TITAN Drill Bit - Clay Bit 200 mm Ø,
screw-on type
part.no. P73-004 6.10 kg pc. stock
TITAN Drill-Bit - Button Type 130, (130 mm Ø)
with carbide buttons, screw-on type
part no. T73-0158 5.5 kg pc. stock
TITAN Drill Bit - Carbide Cross Cut 3 Step 130 (130 mm Ø)
drill bit for directional stability, cuts through several hard layers of soil/rock
part no. P73-0006 5.8 kg pc.
Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flush-
ing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4") male for grout hose, with
lubrication nipple, length 365 mm, to be used in connection with holder only, incl.
transport box,
part.no. T73-0149 32.10 kg pc. stock
complete set of spare seals for R 55 flushing head
(2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm)
part.no. TAC-0021 set stock
Rotary Flushing Head R 55 (2 1/4"), self contained, length 405 mm, no holder
required, 120 mm wrench required, incl. transport box,
part.no. T73-0153 43.70 kg pc.
Flushing Head H 112, for right hand rotary and percussive drilling, for flushing with
water, grout or air, thread BSP 2" male for grout hose, with lubrication nipple, length
300 mm, to be used in connection with holder only, incl. transport box,
part.no. T73-0151 53.20 kg pc.
complete set of spare seals for flushing head H 112
(2 seals 160 x 185 x 16 mm plus 2 guide rings 160 x 165 x 14.8 mm)
part.no. TAC-0022 pc.
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc. stock
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
21
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 103/78 & 103/51
CTS/TITAN Injection Bore Hollow Bar System 103/78
CTS/TITAN Injection Hollow Bar 103/78, design load (60% GUTS) 1369 kN,
continuously right-hand threaded
in 3 m lengths.
black, part.no. T03-0106 24.50 kg/m pc. stock
CTS/TITAN Injection Bore Hollow Bar System 103/51
CTS/TITAN Injection Hollow Bar 103/51, design load (60% GUTS) 2076 kN,
continuously right-hand threaded
in 3 m. lengths.
black, part.no. T03-0120 43.40 kg/m pc. stock
Accessories
Spherical Collar Nut SW 125 x 80,
black, part.no. T03-0110 3.42 kg pc. stock
Coupling Nut 123 mm Ø x 255 mm,
with internal rubber seal, black
2282 KN part.no. T03-0109 7.47 kg pc. stock
Coupling Nut 132 mm Ø x 290 mm,
with internal rubber seal, black
3460 KN part.no. T03-0121 12.6 kg pc.
Bayonet Coupler 135 Ø x 384 mm, recoverable
part.no. P03-002 19.00 kg pc.
Bearing Plate 300 x 300 x 50 mm,
black, part.no. T03-0113 32.60 kg pc.
Drill Bits
TITAN Drill Bit - Cross Cut, 175 mm Ø, for mixed soil with obstacles,
screw-on type
part.no. T03-0108 5.70 kg pc. stock
TITAN Drill Bit - Clay Bit 220 mm Ø,
part.no. P03-002 12.6 kg pc. stock
TITAN Drill Bit - Clay Bit 280 mm Ø
part no. T03-0122 13.9 kg pc. stock
TITAN Drill Bit - Button Type 175, (175 mm Ø), with carbide buttons,
screw-on type
part.no. T03-0119 10.2 kg pc. stock
Centralizer, 165 mm Ø, cast iron,
black, part.no. T03-0101 2.94 kg pc. stock
CTS/TITAN 103/78 & 103/51 Injection Anchors are also available in other
lengths. Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors
and Accessories are also available. Please ask us for pricing.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
22
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 103/78 & 103/51
Accessories
Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flush-
ing with water, grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female, for
grout hose, with lubrication nipple, length 365 mm, to be used in connection with
holder only, incl. transport box,
part.no. T03-0102 40.00 kg pc. stock
complete set of spare seals for R 55 flushing head
(2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm)
part.no. TAC-0021 set stock
Flushing Head, H 112 for right hand rotary and percussive drilling , for flushing with
water, grout or air, thread BSP 2" male, for grout hose, with lubrication nipple, length
300 mm, to be used in connection with holder only, incl. transport box
part.no. T03-0104 48.40 kg pc. stock
complete set of spare seals for H 112 flushing head
(2 seals 160 x 185 x 16 mm plus 2 guide rings 160 x 165 x 14.8 mm)
part.no. TAC-0022 set stock
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc. stock
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
23
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN 130/60
CTS/TITAN Injection Bore Hollow Bar System 130/60
CTS/TITAN Injection Hollow Bar 130/60, design load (60% GUTS) 4764 kN,
continuously right-hand threaded
in 3 m lengths.
black, part.no. T13-0001 79 kg/m pc.
CTS/TITAN 130/60 Injection Anchors are also available in other lengths.
Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors
and Accessories are also available. Please ask us for pricing.
Accessories
Spherical Collar Nut
black, part.no. T13-0003 pc.
Coupling Nut
with internal rubber seal, black
black part.no. T13-0002 pc.
TITAN Drill Bit - Carbide Button Bit 220 mm Ø,
screw-on type
part.no. T13-0004 pc.
CON-TECH SYSTEMS LTDHQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: [email protected] • Website: www.contechsystems.com
CTS/TITAN
24
CTS
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate.
November 2006
CTS/TITAN Hollow Bar Technical Data 3
Drill Bit Selection Chart 5
CTS/TITAN R32 7
Accessories 7
CTS/TITAN T30/11 & T30/16 9
Injection Hollow Bars 9
Accessories 9
CTS/TITAN T40/16 & T40/20 13
Injection Hollow Bars 13
Accessories 13
CTS/TITAN T52/26 17
Injection Hollow Bars 17
Accessories 17
CTS/TITAN T73/56 T73/53 & T73/45 19
Injection Hollow Bars 19
Accessories 19
CTS/TITAN T103/78 & T103/51 21
Injection Hollow Bars 21
Accessories 21
CTS/TITAN T130/60 23
Injection Hollow Bars 23
Accessories 23