September 25, 2014

ROBERT WOO WIKA INSTRUMENTS CANADA L TO 3103 PARSONS RD EDMONTON AB T6N 1 C8 CA

Service Request Type: BPV-Fitting Registration Service Request No.: 1465568 Your Reference No. : Registered to: WIKA INSTRUMENTS CANADA L TO

Dear ROBERT WOO,

14th Floor, Centre Tower 3300 Bloor Street West Toronto, Ontario Canada MBX 2X4 Tel.: 416.734.3300

Fax: 416.231.1626 Toll Free: 1.877.682.8772

www.tasa.org

Technical Standards and Safety Authority (TSSA) is pleased to inform you that your submission has been reviewed and registered as follows:

CRN No.: OH17165.5 Main Design No.: ATS-17502 SHT 7 to SHT 10 REV.A Expiry Date: 25-Sep-2024

Please be advised that a valid quality control system must be maintained for the fitting registration to remain valid until the expiry date.

Note: Pressure- Temperature rating of the assembly is limited by the process connections per main design above.

The stamped copy of the approved registration and the invoice are mailed separately. Should you have any questions or require further assistance, please contact a Customer Service Advisor at 1.877.682.TSSA (8772) or e-mail customerservices@tssa.org. We will be happy to assist you. When contacting TSSA regarding this file, please refer to the Service Request number provided above.

Yours truly,

Rui ing You, ng. Mechanical Eng neer, BPV Tel.: 416-734-3428 Fax: 416-231-6183 Email: ryou@tssa.org

Putting Public Safety First

TECHNICAL STANDARDS & SAFETY AUTHORITY 14th Floor, Centre Tower 3300 Bloor Street West Toronto, Ontario

Show facsimile of manufacturer's logo or trademark, as it will appear on the fitting, in the space below

IWIKAII Canada MBX 2X4 'A' or 'ATS'

STATUTORY DECLARATION Registration of Fittings

I, Robert Woo, P.Eng- Engineering Manager

(Name and Position, e.g. President, Plant Manager, Chief Engineer)

of WIKA Instruments LTD.

(Name of Manufacturer)

Located at 3103 Parsons Road, Edmonton, Alberta, T6N 1C8 (Plant Address)

780-463-7035

(Telephone No.)

780-462-0017

(Fax No.)

[{] do solemnly declare that the fittings listed hereunder, which are subject to the Technical Standards and Safety Act, Boilers and Pressure Vessels Regulation, comply with all of the requirements of ASME BPE, ASME B31.3- 2012

(Title of recognized North American Standard)

which specifies the dimensions, materials of construction, pressure/temperature ratings, identification marking the fittings and service;

0 or are not covered bv the orovisions of a recognized North American standard and are therefore manufactured to comply with --- ----------as supported by the attached data which identifies the dimensions, material of construction, pressure/temperature ratings and the basis for such ratings, the marking of the fitting for identification and service.

I further declare that the manufacture of these fittings is controlled by a quality system meeting the requirements of ISO 9001:2008 _______ which has been verified by the following authority, _A_B_S_A _ __________________ .

The items covered by this declaration, for which I seek registration, are category H type fittings. In support of

this application, the followinq information and/or test data are attached as follows: Drawing ATS-17502 Shts 7-10 Rev A, Design Calculations, CRN OA13351 .5

(drawings, calculations, test reports, etc.)

Declared before me at _ _ .""-f,.c..~L-'/'1-=().'--'/111'-';_C_l/f) _ ____ in the _ ___,_/).L..:.ift-><-'()"-'f!.~W--'L::....!,. {.._ _ _ of I/L6&r A

7 (Signature of Declarer)

FOR OFFICE USE ONLY To the best of my knowledge and belief, the application meets the requirements of the

Technical Standards and Safety Act, Boilers and Pressure Vessels ~e~ulation, and

CSA Standard B51 and is accepted for registration in Category _ __,f-1'--'--------e

CRN:

Registered by:

Dated:

NOTE: This re

PV 09553 ( 11/ 12) f-1tJT£ ;

/ZU(;!Jt~J .., v t

StF Jlrtl+ctl H6t.:Jr C 5 f!+G£ SJ AtJP J>t0(-ttf 11T5--17So 2 ;>Hr 7,--- to UJ.Jv ER. 1-rt ,·5 ci</J ..

:X;;p£ R£Gtst£~rvtJ

Re ~:; fl..

Technical Standards and Safety Authority ili .

14 Floor- Centre Tower ' 3300 Bloor "Street West Toronto, ON M8X 2X4

Service Request No. 1465568 Attn: Gerry Goettl

Re: Project Scope

The TW22 line ofthermowells has options for the thermowell body, the process connection, and the sensor connection. Only the body and process connections are exposed to pressure and are therefore supported by the following documents:

TW22 Thermow.ell (Body and' Tip) Body Style: Straight and Stepped Tip Style: Rounded and Flat Drawing: ATS-17502 sheet 7 See calculations:

External Pressure on Cylindrical Tube, External pressure on Spherical Shell, Unstayed Flat Heads and Covers

THIS IS PART OF CRN Of-{/) t6S:.5 Technical Standards & Safety Authority Boilers & Pressure Vessels

Safely Program

TW22. Thermowell (Weld-on and Compression Process Connections)

WIKA

Styles: Welding ball, Ball-type Compression, Collar-Type Compression, and Straight Drawing: ATS~ l7502 sheet 8 Pressure and temperature limited by thermowell body/tip calculations

TW22 Thermowell (Tri-Clamp Process Connections) Sizes Y:z", %", 1", 1 Y:z", 2", 2 Y:z", 3", 4" Temperature and Pressure limited by Tri-Clamp CRN (OA13351.5) Drawing: ATS-17502 sheet 10

The remaining process connection options require proof-testing and will be submitted at a later date.

Best regards,

Robert Woo, P.Eng. Engineering Manager E-mail: r.woo@wika.ca Phone#: 780-463-7035 Fax#: 780-462-0017