crary cutting systems owner’s manual case ih -...

Manual PN 29486-00Rev. 030111

GOLD Guards

Sickle Sections

Hold Downs

ThunderBOLT Sickle

CASE IH - NEW HOLLAND

CRARY CUTTING SYSTEMS

OWNER’S MANUAL

© 2011, Crary Industries, All rights reserved. Produced and printed in the USA.

DISCLAIMERThis document is based on information available at the time of its publication. While efforts have been made to be ac-curate, the information contained herein does not purport to cover all details or variations, nor to provide for every pos-sible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all systems. Crary Industries assumes no obligation of notice to holders of this document with respect to changes subsequently made.Crary Industries assumes no responsibility for the accuracy, completeness, suffi ciency, or usefulness of the information contained herein.

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE.Crary Industries is continually making improvements and developing new equipment. In doing so, we reserve the right to make changes or add improvements to our product without obligation for equipment previously sold.

Because modifi cation to these systems may affect the performance, function, and safety of its operation, no modifi cations are to be made without the written permission of Crary Industries. Part replacements should be with original equipment supplied by Crary Industries.

THE CRARY INDUSTRIES STATEMENT OF PRODUCT SAFETYAs a manufacturer of specialized agricultural equipment, Crary Industries fully recognizes its responsibility of providing its customers products that perform their expected use in a reasonably safe manner. Safety considerations shall be an integral and high priority part of all engineering/design analysis and judgments involving Crary products. It is our stated policy that our products will be manufactured to comply with the safety standards specifi ed by the American Society of Agricultural Engineers, the National Electrical Code, the Society of Automotive Engineers, and/or any other applicable recognized standards at the time manufactured. However, this statement should not be construed to mean that our product will safeguard against a customer’s own carelessness or neglect in violating common safety practices specifi ed in each product’s manual, nor will we be liable for any such act.

HOW TO REACH US

ADDRESS HOURS TELEPHONEFAX NUMBERE-MAIL

INTERNET

Crary Industries, Inc.237 12th St. NW

West Fargo, ND 58078

Monday-Friday 8 am-5pm (CST)

For Parts and Service:Ph: 701.282.5520 •

800.247.7335Fax: 701.282.9522

Email: [email protected] • [email protected]

Online: www.crary.com

Part Number (s) :

Description of Product:

Date of Purchase:

Where Purchased:

Type of machine it will be used on:

REPLACEMENT PARTSCrary replacement parts are available from your Crary dealer. To obtain prompt, efficient service, please record and have the following information ready when calling the dealer.

Gold’N Cut Cutting Systems - Case IH/New Holland 3

THUNDERBOLTThe Thunder BOLT sickle is an effective alternative to long, difficult, one piece sickle bars. A special overlap-ping design allows the knifeback to be assembled using shorter interlocking pieces. The sections used, either BearCUT or KingKut, will depend on the machine type and its application.

The ThunderBOLT sickle fits most major types of cutting systems. Installation is quick and easy; a sickle section with four holes is placed over four corresponding holes on the knifeback’s split bar area and bolted together - allowing the overall bar strength to remain unchanged. The assembled knifeback is then bolted to the knifehead.

GOLD GUARDSThe GOLD Guard is uniquely designed to double the cutting action of each full sickle stroke. The increased cutting performance

and superior design reduces plant side movement by more than half, thus decreasing shelling and shatter loss. The GOLD Guard allows faster ground speeds and cleaner cutting in Beans, Hay, Lentils and Wheat while decreasing normal guard and sickle breakage.

GOLD Guards fit most major flex, floating and straight com-bine headers, swathers, mowers, windrowers and mower conditioners.

Guards included in the Gold’N Cut system are the standard GOLD Guards (two regular points and two mini-points), Head Guards (black, two regular points and two mini-points), Center Guards (black, two regular points), Left End Guard (one regular point and one mini-point), Right End Guard (one mini-point). The Guards received is dependent on the machine type and size of the cutting system.

HOLD DOWNSSpring Loaded Hold Downs outlast conventional hold downs by featuring replaceable wear pads, while providing a closer tolerance and quick adjustment.

Tdst

BEARCUT & KINGKUT SECTIONS BearCUT sections incorporate larger coined serrations and heavier, high strength, heat treated material to reduce breakage and wear two to four times longer than regular sections. Coined serrations are stamped into the metal before treating enabling a revolutionary wear pattern that reshapes and re-sharpens the sections.

KingKut sections have a 10% - 26% reduced weight from other section de-signs. The KingKut section also provides 33% - 77% more feeding area than other section shapes, allowing for less sickle drive wear and increased ground speeds.

Thank you for purchasing a Gold’N Cut system or other accessories. This product has been designed and tested to of-fer years of dependable service, if installed and maintained correctly. Please take time to completely read this Owner’s manual, paying close attention to the portions regarding safety.

Crary’s Gold’N Cut combines the fi eld proven features of the GOLD Guards, ThunderBOLT sickle, BearCUT or KingKut sections and Spring Loaded Hold Downs for cleaner, faster and more trouble-free cutting performance. It is available for cutting systems measuring 5 to 36 ft. and fi ts most combines, windrowers, and hay machines. Wear Plates, Shims and Mounting Hardware are also included for assembly.

Gold’N Cut Cutting Systems - Case IH/New Holland4

Gold’N Cut WarrantyWarranted for one year from the date of sale to the original consumer purchaser. This warranty does not include breakage of sickle sections under normal use or guards sold only as parts.

This warranty applies only to parts or components which are defective and does not cover repairs necessary due to normal wear, misuse, accidents or lack of proper maintenance. Regular, routine maintenance of the unit to keep it in proper operating condition is the responsibility of the owner.

Crary Industries will warrant its AG Products for 12 months from date of purchase to the original purchaser. Our obligation under this warranty is limited to repairing or replacing, at no charge, any part that in Crary Industries judgement show a defect in material or workmanship. This warranty does not cover merchandise or component parts which, in the opinion of Crary Industries, have been subjected to negligent use, misuse, alteration, ac-cident, or if repairs are made with parts other than those manufactured and obtainable from Crary Industries.

A COMPLETED WARRANTY CLAIM MUST BE SUBMITTED TO CRARY INDUSTRIES WITHIN 30 DAYS OF REPAIR, ALONG WITH PROOF OF PURCHASE BY ORIGINAL PURCHASER.

Parts must be returned to Crary Industries in West Fargo, ND (transportation charges pre-paid). Repair parts will be sent out UPS only (prepaid) to the repairing dealer. Crary Industries will not prepay air freight charges, which will be the responsibility of the dealer or customer, if they choose to have repair parts shipped that way. This warranty shall not be interpreted to render Crary Industries liable for injury or damages of any kind, direct, consequential or contingent to persons or property. This warranty does not extend to loss of crops, losses caused by delays or any expenses or loss for labor, supplies, rental machinery, prospective profi ts or for any other reason.

Except as provided by the Gold’N Cut CUSTOMER SATISFACTION GUARANTEE, there are no warranties, either express or implied, of merchantability or fi tness for particular purpose intended of fi tness for any other reason. This warranty cannot guarantee that existing conditions beyond the control of Crary Industries will not affect our ability to obtain materials or manufacture necessary replacement parts

Neither the dealer nor any other person has any authority to make any warranties or promises on behalf of Crary Industries or to modify the terms or limitation of this warranty in any way. Crary Industries reserves the right to make design changes, improve design or change specifi cations at any time without any contingent obligation to purchasers of machines or parts previously sold.

CRARY CUTTING SYSTEMSCUSTOMER SATISFACTION GUARANTEEIf a customer is unsatisfi ed with the Crary Cutting System’s

performance, the system may be returned for a full refund of the net purchase price.

• Customer must notify Crary Co. of intent to exercise the Customer Satisfaction guarantee within 7 days of first use

• Customer must discontinue use of the cutting system.

• Customer is responsible for shipping costs.

• Proof of purchase is required.


TABLE OF CONTENTSDESCRIPTION PAGE

SAFETY ....................................................................................................6GENERAL SAFETY..........................................................................................................................................7ASSEMBLY SAFETY........................................................................................................................................8OPERATING SAFETY ......................................................................................................................................8MAINTENANCE SAFETY ................................................................................................................................8STORAGE SAFETY .........................................................................................................................................8

ASSEMBLY INSTRUCTIONS ...................................................................9GENERAL INFORMATION ...............................................................................................................................9PRE-ASSEMBLY ..............................................................................................................................................9THUNDERBOLT - SINGLE DRIVE ................................................................................................................10THUNDERBOLT - DOUBLE DRIVE ............................................................................................................... 117222 GUARDS ...............................................................................................................................................127225 GUARDS ...............................................................................................................................................147226 GUARDS ...............................................................................................................................................167228 GUARDS ...............................................................................................................................................187228 GUARDS W/HEAD GUARDS ...............................................................................................................227228 GUARDS W/SINGLE POINT GUARDS ................................................................................................247228 GUARDS W/SINGLE POINT AND HEAD GUARDS .............................................................................267228 GUARDS DOUBLE DRIVES W/CENTER GUARDS ............................................................................287228 GUARDS DOUBLE DRIVES W/CENTER, HEAD AND SINGLE POINT GUARDS ..............................307228 GUARDS DOUBLE DRIVES W/CENTER AND HEAD GUARDS .........................................................337229 GUARDS ...............................................................................................................................................37

PARTS LISTS & ILLUSTRATIONS ........................................................40CASE IH COMBINES .....................................................................................................................................40CASE IH HAY MACHINES .............................................................................................................................46NEW HOLLAND COMBINES .........................................................................................................................54NEW HOLLAND HAY MACHINES .................................................................................................................59GUARDS ........................................................................................................................................................63

PARTS ILLUSTRATIONS .......................................................................63BEARCUT SECTIONS ...................................................................................................................................64KINGKUT SECTIONS ....................................................................................................................................67HALF SECTIONS ...........................................................................................................................................68H & S / DOUBLE POINT SECTIONS .............................................................................................................69WEAR PLATES ..............................................................................................................................................70HOLD DOWNS ...............................................................................................................................................70HOLD DOWN CLEARANCE ..........................................................................................................................72

SPECIFICATIONS ...................................................................................74


SAFETY ALERT SYMBOL

This Safety Alert Symbol means:

ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED!

The Safety Alert symbol identifi es important safety messages on the Air Reel and in the manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety message.

DANGER - Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations, typically for ma chine components that, for functional purposes, cannot be guarded.

WARNING - Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe prac tices.

CAUTION - Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

IMPORTANT - Instructions that must be followed to ensure proper installation/operation of equipment.

NOTE - General statements to assist the reader.

Why is SAFETY important to you?

1. Accidents Disable and Kill2. Accidents Cost3. Accidents Can Be Avoided

SIGNAL WORDS:

Note the use of the signal words DANGER, WARNING, CAUTION, IMPORTANT and NOTE with the safety messages. The appropriate signal word for each mes-sage has been selected using the following guidelines:

3 Big Reasons

SAFETYSection1


YOU are responsible for the SAFE operation and mainte-nance of your Gold’N Cut system. You must ensure that you and any one else who is going to operate, maintain or work around the Gold’N Cut system are familiar with the operat ing and maintenance procedures and related safety information contained in this manual. This manual will alert you to all good safety practices that should be adhered to while operat ing the Gold’N Cut system.

Remember, YOU are the key to safety. Good safety prac-tices not only protect you but also the people around you. Make these practices a working part of your safety program. Be certain that EVERYONE operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices.

• Gold’N Cut owners must give operating instruc tions to operators or employees before allowing them to operate the machine, and at least annually there-after per OSHA (Occupational Safety and Health Administration) regulation 1928.57.

• The most important safety device on this equipment is a safe operator. It is the operator’s responsibility to read and under stand all safety and Operating instructions in the manual and to follow them. All acci dents can be avoided.

• A person who has not read and understood all operating and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible seri-ous injury or death.

• Do not modify the equipment in anyway. Unauthor-ized modification may impair the function and/or safety and could affect the life of the equipment.

GENERAL SAFETY

1. Read and understand the Owner ’s Manual and all safety signs before operat-ing, maintaining, adjusting or servicing the Gold’N Cut System.

2. Only trained persons shall operate the Gold’N Cut system. An untrained operator is not qualified to operate the machine.

3. Have a first-aid kit available for use, should the need arise, and know how to use it.

4. Provide a fire extinguisher for use in case of an accident. Store in a highly visible place.

5. Do not allow children, spectators or by-standers within hazard area of machine.

6. Wear appropriate protective gear. This list Includes but is not limited to:

• A hard hat

• Protective shoes with slip resistant soles

• Protective goggles

• Heavy gloves

• Hearing protection

• Respirator or filter mask7. Wear suitable ear protection for pro-

longed exposure to excessive noise.

8. Place all controls in neutral or off, lower header to the ground, stop combine engine, set parking brake, chock wheels, remove ignition key and wait for all moving parts to come to a complete stop, before servicing, adjusting, repair-ing or unplugging.

9. Review safety related items annually with all person-nel who will be operating or maintain ing the Gold’N Cut system.

SAFETY


1. Follow ALL the operating, maintenance, and safety information in this manual.

2. Support the machine with blocks or safety stands when working around it.

3. Follow good shop practices:

• Keep service area clean and dry.

• Be sure electrical outlets and tools are properly grounded.

• Use adequate light for the job at hand.

• Use only tools, jacks and hoists of sufficient capacity for the job.

4. Place all controls in neutral or off, stop combine engine, set parking brake, chock wheels, remove ignition key and wait for all moving parts to come to a complete stop, before servicing, adjusting, repairing or unplugging.

5. Before resuming work, install and secure all guards when maintenance work is completed.

6. Keep hands, feet, hair and clothing away from all mov-ing and/or rotating parts.

7. Clear the area of bystanders, especially small children, when carrying out any maintenance and repairs or making any adjustments.

8. Keep safety signs clean. Replace any sign that is dam-aged or not clearly visible.

9. First-class maintenance is a prerequisite for the safest operation of your Gold’N Cut system. Maintenance should be performed with the machine stopped and locked out.

1. Read and understand the Owner’s Manual and all safety decals before servicing, adjusting or repairing.

2. Install and secure all guards and shields before starting or operating.

3. Keep hands, feet, hair and clothing away from all mov-ing and/or rotating parts.

4. Place all controls in neutral or off, lower header to the ground, stop combine engine, set parking brake, chock wheels, remove ignition key and wait for all moving parts to come to a complete stop, before servicing, adjusting, repairing or unplugging.

5. Clear the area of bystanders, especially small children, before starting.

6. Review safety related items annually with all person-nel who will be operating or maintaining the Gold’N Cut system.

OPERATING SAFETY

MAINTENANCE SAFETY

STORAGE SAFETY

ASSEMBLY SAFETY

1. Store the unit in an area away from human activity.

2. Do not permit children to play on or around the stored machine.

3. See the Owner’s Manual that came with your combine for additional storage information.

1. Assemble in an area with sufficient space to handle the largest component and access to all sides of the machine

2. Use only lifts, cranes and tools with sufficient capacity for the load.

3. When necessary, have someone assist you.

4. Do not allow spectators in the working area.

SAFETY


ASSEMBLY INSTRUCTIONSSection2

PRE-ASSEMBLYGOLD GUARDS HOLD DOWNS THUNDERBOLT

Clean any extra paint or built up material from the header platform before installing.

Remove any burrs and nicks from the mounting area.

Use a new knife assembly or a straight one (not badly worn) when aligning guards.

Do not use a hammer or pry up with a screwdriver to tighten the wear plates against the knifeback.

Shims should not be needed if mounting 7222 standard guards on header platforms that are 1/4” or thicker. Header platforms less than 1/4” will require shims.

When mounting 7229 standard guards on header platforms that are 3/8” or thicker, shims should not be needed. Header platforms less than 3/8” will require shims.

Sand off any rust or corrosion on sickle sections which may contact the wear pads.

Additional hold downs may be in-stalled to provide a more uniform hold down pressure.

When replacing hold downs, use no less than original number of OEM hold downs.

After hold downs have been ad-justed, run the system at full speed for a few minutes. Check for “hot spots” at hold down locations and adjust as needed.

Typically hold downs are set at .020 inches from the sickle. However, in tougher cutting conditions, such as hay, the hold downs should be set closer (down to .005 inches).

Binding problems can result from insufficient clearance between the sickle and hold downs. Exist-ing hold downs may need to be replaced with ones that allow more clearance for nuts.

On double drive systems, make sure to assemble both sickles correctly. See the thunderbolt section of the manual for correct assembly instructions.

Refer to the OEM owners manual for information on adjusting the sickles, setting the knife, and knife timing.

GENERAL INFORMATIONIn general, the Gold’n Cut is set up exactly the same as the OEM sickle system. The Gold’n Cut system usually will replace the OEM sickle, guards, and hold downs part for part. Use your packing slip for parts quantity information and guard descriptions. If all parts are not included contact your Crary Industries dealer.

The sickle head is not included in the system, but may be ordered extra from your Crary dealer. Normally, the original sickle head is used and can be bolted to the ThunderBOLT sickle.

In general, after determining a starting point, the hold downs are placed on every other guard. The clearance of the hold downs should be between .005” and .020”. The clearance should never be greater than .020. In hay, closer tolerances are required. In grain, the hold downs can be set at the upper end of the scale.

REMEMBERUse your packing

slip for parts and

quantity information.

If all parts are not

included, contact your

Crary Dealer.

Need help identifying parts??Finding out is easy!

Use the Parts List and Illustration section to determine what the parts look like and how many you need!


ASSEMBLY

THUNDERBOLT - SINGLE DRIVEGENERAL INSTRUCTIONS:1. Refer to your machine’s owner’s manual for removal of existing OEM sickle bar.

2. Verify all standard sections are tight on ThunderBOLT.

3. Align ThunderBOLT spliced ends, as shown in Figure 2.1.

4. Connect bars with a joint sickle section, four bolts and four nuts per joint.

5. Tighten the nuts. Do not over tighten; recommended torque is 50-60 in./lbs.

6. Check the ThunderBOLT joints. They must be straight and seated tight with the section bolts before installing onto the header/platform. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.

7. Inspect the assembled sickle bar. Remove any twists or bends in the knifeback that may result in poor cutting action or excessive wear.

Need help identifying parts?? Finding out is easy!Use the Parts List and Illustration section to determine what the parts look like and how many you need!

Figure 2.1 - ThunderBOLT Assembly (Single Drive)


ASSEMBLY

THUNDERBOLT - DOUBLE DRIVEGENERAL INSTRUCTIONS:1. Refer to your machine’s owners manual for removal of existing OEM sickle bar assemblies.

2. Verify all Gold’N Cut standard sections are tight.

3. Align sickle bar spliced ends.

4. On the left knife, connect the ThunderBOLT as illustrated in Figure 2.2. Four bolts and nuts are used on each joint.

5. On the right knife, two or more sickle bars may be used. One sickle bar uses the standard ThunderBOLT system as shown in Figure 2.1. The other sickle bar uses an overlap strap that is connected to the top of the section (Figure 2.2). Connect the appropriate ThunderBOLT sickle bar.

6. Tighten the nuts. Do not over tighten; recommended torque is 50-60 in./lbs.

7. Check the ThunderBOLT joints. They must be straight and seated tight with the section bolts before installing onto the header platform. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.

8. Verify the overlap area (generally the top of the left knife assembly and the bottom of the right knife assembly—some machines may be opposite) is smooth to prevent interference. Figure 2.2 illustrates special right knife sections with countersunk holes on the bottom to allow a flush bolt head to fit underneath. The left knife’s special sections have countersunk holes on the top for a flush bolt head fit on the top side.

9. Inspect the assembled sickle bar. Remove any twists or bends in the knifeback that may result in poor cutting action or excessive wear.


COUNTERSUNK BOLTS

Figure 2.2 - ThunderBOLT Assembly (Double Drive).


ASSEMBLY

7222 GUARDSNEW HOLLAND: 960 RIGID HEADER

GENERAL INSTRUCTIONS:

1. Install new guards starting and working from left to right replacing the OEM guards with Crary Guards as you go.

2. Install the wear plates, with the curled edge turned downward, to alternating guards beginning with the second full guard from the sickle head. 6” wear plates are used across the length of the header.

3. Attach hold downs above the wear plates starting with the head hold down and continuing with regular spring loaded hold downs. Do not tighten at this time. Use shims to adjust rear wear pad clearance to .020”.

4. Bolt knifeback to the knifehead. Recommended torque is 50-60 In-lbs. If necessary, bolt the ThunderBolt together at this time. Slide the sickle into the guards from the left side.

5. Guards may need adjustment to ensure the knife rests level on the platform.

6. Adjust wear plates snugly against the back of the knifeback.

7. Tighten guard bolts and torque to 30 Ft-lbs.

8. Using the adjustment bolts, position the heads of the hold downs to obtain .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions, the hold downs can be adjusted down to .005”.

MODEL VARIATIONS:

THUNDERBOLT: None, one, or two ThunderBolt splices will be used when mounting this Gold’N Cut system. When installing the ThunderBolt, make sure to follow the ThunderBolt assembly instruction in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.

NOTES: Shims should not be needed if mounting 7222 standard guards on header platforms 1/4” or thicker. Header platforms less than 1/4” will require shims.


ASSEMBLY

7222 GUARDS -- NEW HOLLAND 960 RIGID

LEFT SECTION

HOLD DOWN24911

HOLD DOWN24344

WEAR PLATE17329

GOLD GUARD7222

SLIDE SICKLEIN HERE


ASSEMBLY

7225 GUARDS

CASE IH: 810 RIGID W/HART CARTER GEN II FLOATING CUTTERBAR (PITMAN DRIVE)


1. Install new guards starting and working from left to right. Remove and replace the OEM head guards, 3-point guard (if equipped) and standard guards with the provided head guards, 3-point guard and standard GOLD guards.

2. Install the wear plates, with the curled edge turned upward, to alternating guards beginning with the second full guard from the left hand side (replace at OEM locations).

3. Attach hold downs above the wear plates, starting with head hold downs (install at OEM location), and continuing with spring loaded hold downs. Hold downs are mounted every other guard.

4. Bolt guards and hold downs to the header. Do not tighten. Use shims to adjust rear wear pad clearance to .020”.

5. Bolt knifeback to the knifehead. Recommended torque is 50-60 In-lbs. If equipped, bolt the ThunderBolt together at this time. Slide the sickle into the guards from the left side.

6. Guards may need adjustment to ensure the knife rests level on the ledger surface.

7. Adjust wear plates snugly against the back of the knifeback.


9. Using the adjustment bolts, position the heads of the hold downs to obtain .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions, clearance can be adjusted up to .005”.

MODEL VARIATIONS:

TRIPLE GUARD: Remove the OEM guard and replace with the Crary guard in the same location.

THUNDERBOLT: None, one, or two ThunderBolt splices will be used when mounting this Gold’N Cut system. When installing the ThunderBolt make sure to follow the instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.


ASSEMBLY

7225 GUARDS - - AGCO 7225 GUARDS - - CASE IH

LEFT SECTION

3 POINT GUARD

SLIDE SICKLEIN HERE

HOLD DOWN17418

HOLD DOWN24351

GOLD GUARD7225

WEAR PLATE17329

HEAD GUARD22064

3-POINT GUARD21549


ASSEMBLY

7226 GUARDSCASE IH: 810 RIGID OR W/HINIKER FLOATING CUTTERBAR


1. Remove all OEM components from the header.

2. Install new guards starting and working from left to right. Only 7226 Guards are used.

3. While installing the guards attach the hold downs with the head hold down and continuing with regular spring loaded hold downs.

4. Bolt guards and hold downs to the header. Do not tighten. Use shims to adjust rear wear pad clearance to .020”.

5. Bolt knifeback to the knifehead. Recommended torque is 50-60 in./lbs. Bolt the ThunderBolt together according to the installation instructions in this manual. Slide the sickle into the guards from the left side.


7. Tighten guard bolts securely (bolt torque should be 52 ft./lbs.).

8. Using the adjustment bolts, position the heads of the hold downs to obtain .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions hold downs can be adjusted down to .005”.

MODEL VARIATIONS:

THUNDERBOLT: None, one, or two ThunderBolt splices will be used when mounting this Gold’n Cut system. When installing the ThunderBolt, make sure to follow the ThunderBolt assembly instruction in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.




ASSEMBLY

7226 GUARDS -- CASE 810 RIGID OR W/HINIKER FLOATING CUTTERBAR

LEFT SECTION

SLIDE SICKLEIN HERE

GOLD GUARD7226

HOLD DOWN24911

HOLD DOWN24337


ASSEMBLY

7228 GUARDS

CASE IH: 1020 FLEX HEADER


1. Install new guards starting and working from left to right. Remove the old guards and replace with the new Crary guards as you go. The three head guards are positioned before the standard GOLD guards. On 15, 20, 25 & 30 ft. headers, install in the following order: one stub guard, three head guards, the standard GOLD guards and the remaining stub guard.

2. Attach hold downs starting with the head hold down and continuing with regular spring loaded hold downs. Use shims to adjust rear wear pad clearance to .020”.

3. Bolt guards and hold downs to the header. Do not tighten.

4. Bolt knifeback to the knifehead. Connect the ThunderBolt(s) at this time. Recommended torque is 50-60 in./lbs. Slide the sickle into the guards from the left side.



7. Using the adjustment bolts, position the heads of the hold downs to obtain .020” clearance between the top of the sections and the wear pads. In tough cutting conditions hold downs can be adjusted to .005”.

MODEL VARIATIONS:

THUNDERBOLT: None, one, or two ThunderBolt splices will be used when mounting this Gold’n Cut system. When installing the ThunderBolt, make sure to follow the ThunderBolt assembly instruction in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.



ASSEMBLY

7228 GUARDS W/HEAD AND END GUARDS -- CASE 1020 FLEX

LEFT SECTION

RIGHT SECTION

HEAD GUARD22063

END GUARD24361

HOLD DOWN25454

HOLD DOWN24338

GOLD GUARD7228

SLIDE SICKLEIN HERE

END GUARD24361


ASSEMBLY

7228 GUARDSCASE IH: 555, 950, 1050, 1155, 1160, 1075, 1085, 1275

NEW HOLLAND: 451, 461, 465, 467, 469, 472, 474, 477, 478, 479, 488, 489, 490, 492, 495, 903, 905, 1100, 1465, 1469, 1495


1. Install new guards starting and working from left to right replacing the OEM guards with Crary Guards as you go.

2. Position hold downs on alternating guards beginning with the second full guard from the sickle head. Start with head hold downs (1 or 2) and continue with regular spring loaded hold downs.

3. Bolt guards and hold downs to the platform. Do not tighten. Use shims to adjust rear wear pad clearance to .020”.

4. Bolt knifeback to the knifehead. Connect the ThunderBOLT(s) at this time. Recommended torque is 50-60 In-lbs. Slide the sickle into the guards from the left side.



7. Adjust the hold downs using the adjustment bolt to achieve .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions, hold downs can be adjusted to .005”.

MODEL VARIATIONS:

Head Area Hold Downs: One or two head area hold downs are used. Check your packing slip for details on how many of these hold downs are used on your machine.

ThunderBolt: Up to two ThunderBolt splices will be used when mounting this Gold’n Cut system. When installing the ThunderBolt make sure to follow the instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.



ASSEMBLY

LEFT SECTION

7228 GUARDS -- NEW HOLLAND 451,456, 461, 467, 469...

SLIDE SICKLE IN HEREGOLD GUARD

7228

HOLD DOWN24911

HOLD DOWN24338


ASSEMBLY

7228 GUARDS W/HEAD GUARDSCASE IH: 810 HEADERS W/HART CARTER GEN II FLOATING CUTTERBAR (PITMAN DRIVE), 810 HEADERS W/HART CARTER GEN III FLOATING CUTTERBAR (WOBBLEBOX), 721, 725, 730, 736, 742, 750, 6000, 6500

NEW HOLLAND: 451, 456, 461, 499, 970, 971, 972, 973 (NON-DOUBLE DRIVE), 1469, 1496, PIVOT TONGUEGENERAL INSTRUCTIONS:1. Install new guards starting and working from left to right replacing the OEM guards with Crary guards as you go.

Head Guards are positioned before the standard GOLD Guards.

2. Position hold downs on alternating guards beginning with the second full guard from the sickle head. Start with the head hold down and continue with spring loaded hold downs.





7. Using the adjustment bolts, position the heads of the hold downs to obtain .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions the hold downs can be set at .005”.

MODEL VARIATIONS:Head Guard: Up to three head guards are used. Check your packing slip for details on how many of these guards are used on your machine. The head guards are installed before the 7228 guards.

ThunderBolt: Up to two ThunderBOLT splices will be used when mounting this Gold’N Cut system. When installing the ThunderBolt make sure to follow the instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.

LEFT SECTION

7228 GUARDS W/HEAD GUARDS -- CASE 810 RIGID GEN II, 721, 725, 730, 736, 742, 750, 6000, 6500

AND NH 970 (NH HAS ONLY 2 SHIMS)

HOLD DOWN24911

HOLD DOWN24338

SLIDE SICKLEIN HERE

GOLD GUARD7228


ASSEMBLY

7228 GUARDS W/HEAD GUARDS -- CIH 2020, 3020 & NEW HOLLAND , 971, 972, 973, 73C, 74C, 740 (SINGLE DRIVE)

LEFT SECTION

RIGHT SECTION

RH END GUARD54100-12

HOLD DOWN24911

HOLD DOWN24338

HOLD DOWN PLATE (SHORT)(NOT USED FOR CIH3020 & NH740)23621

HOLD DOWN PLATE (LONG)(NOT USED FOR CIH3020 & NH740)23652

HEAD GUARD22063

SLIDE SICKLE IN HERE


ASSEMBLY

7228 GUARDS W/SINGLE POINT GUARDS

CASE IH: 88, 120, 130, 13, 140, 188, 200, 230, 240, 580, 590, 780, 800, 830, 1209, 1214, 1219, 1380, 1424, 2250, 2270, 2280, 2320, 2360, 2420, 8200 & 8220 (PULL TYPE), 8320, 8330, 8350, 8360, 8370, 8830


1. Remove existing guards, hold downs, strip plates and shims from the platform. Take note as to where the parts were located.

2. On a machine with a 1/4” cutterbar, reinstall the original strip plate.

3. Install new guards starting and working from left to right. Replace the OEM standard guards and single point guard with the provided single point guard and standard GOLD guards at OEM locations.

4. Position hold downs on alternating guards beginning with the second full guard from the sickle head. Start with the head hold down and continue with regular spring loaded hold downs.


6. Bolt knifeback to the knifehead. Connect the ThunderBOLT(s) at this time. Recommended torque is 50-60 in./lbs. Slide the sickle into the guards from the left side.



9. Adjust the hold downs with the adjustment bolt to achieve .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions the hold downs can be set at .005”.

MODEL VARIATIONS:

Head Area Hold Downs: One or two head area hold downs are used. Check your packing slip for details on how many of these hold downs are used on your machine.

Single Point Guards: Install the Crary single point guard at the location where the OEM single point guard was removed.

ThunderBolt: Up to two ThunderBOLT splices will be used when mounting this Gold’N Cut system. When installing the ThunderBolt make sure to follow the instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.


ASSEMBLY

7228 GUARDS W/SINGLE POINT GUARDS -- CASE

LEFT SECTION

RIGHT SECTION

SLIDE SICKLEIN HERE

HOLD DOWN24911

HOLD DOWN24338

GOLD GUARD7228

SINGLE POINT GUARD13454-00


ASSEMBLY


7228 GUARDS W/SINGLE POINT AND HEAD GUARDSCASE IH: 1100, 1300, 1490 (12’), 1590 (14’), 4000, 5000, 5500 W/DUAL AUGER HEADER, SERIES 100 BALANCED HEADERS, MOWER/CONDITIONER 990, ALL MOWERS


1. Remove existing guards, hold downs, strip plates and shims from the platform. Take note as to where the parts were located.

2. Install new guards starting and working from left to right. Replace the OEM head guards, standard guards and single point guard with the provided head guards, single point guard and standard GOLD guards at OEM locations.

3. Position hold downs on alternating guards beginning with the second full guard from the sickle head. Start with the head hold down and continue with regular spring loaded hold downs.




7. Tighten guard bolts securely (bolt torque should be 52 Ft-lbs.).

8. Adjust the hold downs, using the adjustment bolt, to achieve .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions the hold downs can be set at .005”.

MODEL VARIATIONS:

Head Guard: Two to four head guards are used. Check your packing slip for details on how many of these guards are used on your machine. The head guards are installed before the 7228 guards.

Head Area Hold Downs: One or two head area hold downs are used. Check your packing slip for details on how many of these hold downs are used on your machine. Head area hold downs are installed before spring loaded hold downs.

Single Point Guards: Install the Crary single point guard at the location where the OEM single point guard was removed.

ThunderBolt: One or two ThunderBolt splices will be used when mounting this Gold’N Cut system. When installing the ThunderBolt make sure to follow the instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.


ASSEMBLY

7228 GUARDS W/SINGLE POINT AND HEAD GUARDS -- CASE

LEFT SECTION

RIGHT SECTION

SLIDE SICKLEIN HERE

HEAD GUARD22063

GOLD GUARD7228

HOLD DOWN24911

HOLD DOWN24338

SINGLE POINT GUARD22659


ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/CENTER GUARDS

NEW HOLLAND: MOWER/CONDITIONER 499, 1496, 1499 WINDROWER


1. Install new guards starting and working from left to right. Replace the existing OEM center guards and standard guards with the provided center guards and standard GOLD guards.

2. Use if system included high head area hold downs: Position hold downs on alternating guards beginning with the second full guard from the sickle heads. Start with high head hold downs, continue with regular spring loaded hold downs, and use high head hold downs again in the overlap area.

3. Use if only standard hold downs are included in system: Position hold downs on alternating guards beginning with the second full guard from the sickle heads.

4. Bolt guards and hold downs to the cutterbar. Do not tighten. Use shims to adjust rear wear pad clearance to .020”.

5. Bolt knifeback to the knifehead. Connect the ThunderBolt(s) at this time. Recommended torque is 50-60 In-lbs. Slide the sickle into the guards from the respective ends (i.e. right and left).



8. Adjust the hold downs using the adjustment bolt to achieve .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions the hold downs can be set at .005”.


ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/CENTER GUARDS -- NEW HOLLAND 499, 1496, 1499

LEFT SECTION

CENTER SECTIONRIGHT SECTION

SLIDE SICKLEIN HERE

GOLD GUARD7228

HOLD DOWN24911

HOLD DOWN24338

HOLD DOWN24911

CENTER GUARD22827

HOLD DOWN24911


ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/CENTER, HEAD AND SINGLE POINT GUARDS

CASE IH: MOWER/CONDITIONER 8840, 8870, 8830 W/625 HEADER, 425 HEADER, SC 414 & 416, 8820 SINGLE AUGER HEADER


1. Install new guards starting and working from left to right. Replace the OEM head, standard, center, and single point guard with the provided Crary head, Gold, center, and single point guards at OEM locations.

2. Position hold downs on alternating guards beginning with the second full guard from the sickle head. Start on the ends with head hold downs and continue with spring loaded hold downs. Depending upon the model, head area hold downs may be used in the middle. On some models two different spring loaded hold downs are used. On these models the spring loaded hold downs with the thicker wear pads are placed on the side of the upper sickle. The upper sickle is the one that is located on top of the other sickle at the overlap area.


4. Bolt knifeback to the knifehead. Connect the ThunderBOLT(s) at this time. Recommended torque is 50-60 in./lbs. Slide the sickle into the guards from the respective ends (i.e. right and left).




MODEL VARIATIONS:

Head Guard: One to four head guards are used. Check your packing slip for details on how many of these guards are used on your machine. The head guards are installed before the 7228 guards.

Head Area Hold Downs: One or two head area hold downs are used. Check your packing slip for details on how many of these hold downs are used on your machine. Head area hold downs are installed before spring loaded hold downs at OEM locations.

Single Point Guards: Install the Crary single point guard at the location where the OEM single point guard was re-moved. One to two single point guards are used.

Center Guards: Install the Crary center guards at the location where the OEM center guard was removed. One to two center guards are used.

ThunderBolt: One or two ThunderBolt splices will be used when mounting this Gold’N Cut system. When installing the ThunderBolt make sure to follow the instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.



ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/CENTER AND SINGLE POINT GUARDS -- CASE 8840, 8870, 8830 W/625 HEADER

LEFT SECTION

CENTER SECTION

RIGHT SECTION

HOLD DOWN24911

HOLD DOWN24338

SLIDE SICKLEIN HERE

GOLD GUARD7228

CENTER GUARD22847

HOLD DOWN24911


HOLD DOWN24911


ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/CENTER AND SINGLE POINT GUARDS -- CASE 8840, 8870, 8380

SLIDE SICKLEIN HERE

HOLD DOWN25615

GOLD GUARD7228

CENTER GUARD22847

HOLD DOWN24911

HOLD DOWN24338



ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/CENTER AND HEAD GUARDS

NEW HOLLAND: WINDROWER 907, 909,910, 912, 1110, 1112, 1114, 1116, 1118, 116, 1100 W/HIGH PERFORMANCE HEADER, PIVOT TONGUE 114, WINDROWERS W/1475 DOUBLE OVERLAP SIDE 2200, 2300, 2450, 2550, MOD-ELS 970, 971, 972, 973, 73C, 74C HEADERS (DOUBLE DRIVE)

GENERAL INSTRUCTIONS:1. Install new guards starting and working from left to right. Replace the OEM head, standard, and center guard with

the provided Crary head, Gold, and center guards at OEM locations.

2. Use if system included Head Area Hold Downs: Position hold downs on alternating guards beginning with the second full guard from the sickle heads. Start with head area hold downs, continue with regular spring loaded hold downs, and use head area hold downs again in the overlap area and on the other side of the sickle.

3. (Use for all other systems) Position hold downs on alternating guards beginning with the second full guard from the sickle heads. The spring loaded hold downs with the thinner wear pads are placed on the side of the upper sickle. The upper sickle is the one that is located on top of the bottom sickle at the overlap area. The hold downs with the thicker wear pads go on the side of the bottom sickle.

4. Bolt guards and hold downs to the cutterbar. Do not tighten. Use shims to adjust wear rear pad clearance to .020”.

5. Bolt knifeback to the knifehead. Connect the ThunderBolt(s) at this time. Recommended torque is 50-60 in./lbs. Slide the sickle into the guards from the respective ends (i.e. right and left).




MODEL VARIATIONS:

Head Guard: Two head guards are used. The head guards are installed before the 7228 Guards.

Head Area Hold Downs: One head area hold downs are used. Check your packing slip for details on how many of these hold downs are used on your machine. Head area hold downs are installed before regular spring loaded hold downs at OEM locations.

Center Guards: Install the Crary center guard at the location where the OEM center guard was removed. One center guard is used.

ThunderBolt: One or two ThunderBolt splices will be used when mounting this Gold’n Cut system. When installing the ThunderBolt make sure to follow the instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.


ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/CENTER AND HEAD GUARDS -- NH 1475 W/DOUBLE 2200, 2300, 2450, 2550

LEFT SECTION

CENTER SECTION

RIGHT SECTION

SLIDE SICKLEIN HERE

HEAD GUARD22063

GOLD GUARD7228

HOLD DOWN25615

HOLD DOWN24911

CENTER GUARD22847

HOLD DOWN24338

HEAD GUARD22063


ASSEMBLY

7228 GUARDS--DOUBLE DRIVES W/CENTER AND HEAD GUARDS -- CIH 2020 & NEW HOLLAND 971, 972, 973, 73C, 74C

LEFT SECTION

CENTER SECTIONRIGHT SECTION

SLIDE SICKLEIN HERE

HEAD GUARD7228

GOLD GUARD7228

HOLD DOWN24911

HOLD DOWN24338

HOLD DOWN PLATE (SHORT)23621

HOLD DOWN PLATE (LONG)23652

3 POINT GUARD (CENTER GUARD)21579

HOLD DOWN24911

MODIFIEDHEAD GUARD

53817-12

HEAD GUARD22063


ASSEMBLY

7228 GUARDS DOUBLE DRIVES W/HEAD GUARDS -- NEW HOLLAND 970

LEFT SECTION

3 POINTSECTION

RIGHT SECTION

SLIDE SICKLEIN HERE

GOLD GUARD7228

HOLD DOWN24911

HOLD DOWN24338

HOLD DOWN24911

3 POINT GUARD21579

HOLD DOWN24911


ASSEMBLY

7229 GUARDSCASE IH: 1020 FLEX HEADER

GENERAL INSTRUCTIONS:1. Install new guards starting and working from left to right. Remove the old guards and replace with the new Crary

guards as you go. The three head guards are positioned before the standard GOLD Guards. On 15, 20, 25 & 30 ft. headers, install in the following order: one stub guard, three head guards, the standard GOLD Guards and the remaining stub guard.

2. Install the offset wear plates, with the curled edge turned downward, to alternating guards beginning with the second full guard from the sickle head.

3. Install the standard wear plates, between the offset wear plates, with the lip facing upwards. These are used to help hold the back of the sickle down and must be shimmed so they fit over the sickle with .020” clearance.

4. Attach hold downs above the offset wear plates starting with the head hold down and continuing with spring loaded hold downs. Use shims to adjust rear wear pads to .020”.

5. Bolt guards and hold downs to the header. Do not tighten.

6. Bolt knifeback to the knifehead. Connect the ThunderBolt(s) at this time. Recommended torque is 50-60 In-lbs. Slide the sickle into the guards from the left side.


8. Adjust offset wear plates snugly against the back of the knifeback.


10. Using the adjustment bolts, position the heads of the hold downs to obtain .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions, hold downs can be adjusted to .005”.

7229 GUARDS -- CASE IH COMBINES 1020 FLEX

LEFT SECTIONRIGHT SECTION

SLIDE SICKLEIN HERE

END GUARD24361

HEAD GUARD22063

GOLD GUARD7229

HOLD DOWN25348

WEAR PLATE, OFFSET24261

WEAR PLATE17329

HOLD DOWN25615

END GUARD24361


ASSEMBLY

7229 GUARDSCASE IH: 820 FLEX HEADER, 1010 RIGID (3” SICKLE)

GENERAL INSTRUCTIONS:1. Install new guards starting and working from left to right. Guards should be replaced as they are taken off.

2. Install the wear plates, with the curled edge turned downward, to alternating guards beginning with the second full guard from the sickle head.

3. Attach hold downs above the wear plates starting with the head hold down and continuing with spring loaded hold downs.

4. Bolt guards and hold downs to the header. Do not tighten. Use shims to adjust rear wear pad clearance to .020”. Shims shouldn’t be needed if the platform is 3/8” or thicker.

5. Bolt knifeback to the knifehead. Recommended torque is 50-60 In-lbs. Slide the sickle into the guards from the left side. If necessary, bolt the Thunderbolt together at this time.


7. Adjust wear plates snugly against the back of the Sickle.


9. Using the adjustment bolts, position the heads of the hold downs to obtain .020” clearance between the top of the sections and the bottom of the wear pads. In tough cutting conditions hold downs can be adjusted down to .005”.

MODEL VARIATIONS:Head Guard: Three head guards are used on Case-IH systems.

End Guard: One end guard is used on Case-IH 820 systems. The end guard is mounted before the head guards.

ThunderBolt: One or two ThunderBolt splices will be used when mounting this Gold’n Cut system. When installing the ThunderBolt make sure to follow the ThunderBolt installation instructions in this manual. The sickle bars must be pressed together by the bolts or the tabs of the sickle will eventually shear off.

7229 GUARDS -- 820 FLEX

LEFT SECTION

HOLD DOWN24911

HOLD DOWN24335

WEAR PLATE17329

GOLD GUARD7229

HEAD GUARD22063

END GUARD24361

SLIDE SICKLEIN HERE


ASSEMBLY

7229 GUARDS -- CASE 1010 RIGID

LEFT SECTION

HOLD DOWN24911

HOLD DOWN24335

WEAR PLATECURLED EDGE DOWN

GOLD GUARD7229

HEAD GUARD22063

SLIDE SICKLEIN HERE


PARTS LISTS & ILLUSTRATIONSSection3

CASE IH COMBINESHEADER: 810 RIGID W/HART CARTER GEN II FLOATING CUTTERBAR (PITMAN DRIVE)

DESCRIPTION 13 FT. 15 FT. 16 FT. 16.5 FT. 17.5 FT. 18 FT. 20 FT. 22.5 FT.GOLD’N CUT COMPLETE SYSTEM (7225) (BC) 19838 19839 19840 19870 19871 19425 19841 19872 COMPLETE SICKLE (7225) 19830 19831 19832 19864 19865 19407 19833 19866

-LEFT HAND SICKLE 28114 28114 28114 28114 28114 28114 28114 28114-CENTER SICKLE - - - - 24238 24238 24238 24238-RIGHT HAND SICKLE 24241 24240 24239 28118 28128 24243 24242 28122

COMPLETE SICKLE (OEM) 24004 24005 24006 24007 24008 24009 24010 24011-LEFT HAND SICKLE 24003 24003 24003 24003 24003 24003 24003 24003-CENTER SICKLE - - - - 23990 23990 23990 23990-RIGHT HAND SICKLE 23996 23999 24001 24002 23991 23992 23994 23998

PART # DESCRIPTION QTY QTY QTY QTY QTY QTY QTY QTY

7225 GUARD, GOLD 23 27 29 30 32 33 37 4222064 GUARD, HEAD 2 2 2 2 2 2 2 221549 GUARD, 3-POINT 1 1 1 1 1 1 1 117206 SECTION, GOLD (BC) (7225) 52 60 64 66 70 72 80 9017205 SECTION, GOLD (BC) (OEM) 52 60 64 66 70 72 80 9024351 HOLD DOWN (SPRING LOADED) 12 14 15 15 16 17 19 2117418 HOLD DOWN (SPRING LOADED HEAD) 2 2 2 2 2 2 2 217329 WEAR PLATE (6”) 14 16 17 17 18 19 21 2322523 SHIM (.010) 14 16 17 17 18 19 21 2315304 BOLT, 7/16 X 1-1/2” PLOW 46 54 58 60 64 66 74 8415305 BOLT, 7/16 X 1-3/4” PLOW 4 4 4 4 4 4 4 415052 NUT, 7/16” SERR. FLANGE 50 58 62 64 68 70 78 88


PARTS LISTS

CASE IH COMBINESHEADER: 810 RIGID W/HART CARTER GENERATION III FLOATING CUTTERBAR (WOBBLE BOX)

DESCRIPTION 13 FT. 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT.GOLD’N CUT COMPLETE SYSTEM (7228) (BC) 23834 23835 23836 23837 23838 23839 COMPLETE SICKLE 24244 24245 24246 24247 24248 24249

-LEFT HAND SICKLE 23820 23820 23820 23820 23820 23820-CENTER SICKLE - - - 23822 23822 23822-RIGHT HAND SICKLE 23828 23830 23833 23823 23826 23829

KINGKUT COMPLETE SYSTEM (KK) 27305 27306 27307 27308 27309 27310 COMPLETE SICKLE (OEM) 27299 27300 27291 27302 27303 27304

-LEFT HAND SICKLE 27062-00 27062-00 27062-00 27062-00 27062-00 27062-00-CENTER SICKLE - - - 27071-00 27071-00 27071-00-RIGHT HAND SICKLE 27074-00 27075-00 27082-00 27077-00 27073-00 27079-00

PART # DESCRIPTION QTY QTY QTY QTY QTY QTY7228 GUARD, GOLD 25 29 32 34 39 4422063 GUARD, HEAD 1 1 1 1 1 117318 SECTION, GOLD (BC) (7228) 52 60 66 70 80 9014765 SECTION, KINGKUT (KK) 52 60 66 70 80 9024338 HOLD DOWN (SPRING LOADED) 12 14 15 16 19 2124911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 1 1 122523 SHIM (.010) 26 30 32 34 40 4422524 SHIM (.024) 26 30 32 34 40 4415241 BOLT, 7/16 X 1/2” CARRIAGE 26 30 34 36 40 4615082 BOLT, 7/16 X 2” CARRIAGE 26 30 32 34 40 4415052 NUT, 7/16” SERR. FLANGE 52 60 66 70 80 90

HEADER: W/HART CARTER GENERATION III FLOATING CUTTERBAR (WOBBLE BOX)DESCRIPTION 13 FT. 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT.

GOLD’N CUT COMPLETE SYSTEM (7225) (BC) 19422 19423 19316 19883 19426 19884 COMPLETE SICKLE 19404 19405 19325 19877 19408 19878


PART # DESCRIPTION QTY QTY QTY QTY QTY QTY7225 GUARD, GOLD 25 29 32 34 39 4422064 GUARD, HEAD 1 1 1 1 1 117205 SECTION, GOLD (OEM) 52 60 66 70 80 9017206 SECTION, GOLD (7225) 52 60 66 70 80 9024351 HOLD DOWN (SPRING LOADED) 12 14 15 16 19 2124911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 1 1 117329 WEAR PLATE (6”) 13 15 16 17 20 2222523 SHIM (.010) 13 15 16 17 20 2215304 BOLT, 7/16 X 1-1/2” PLOW 26 30 32 34 40 4415306 BOLT, 7/16 X 2” PLOW 26 30 34 36 40 4615052 NUT, 7/16” SERR. FLANGE 52 60 66 70 80 90

DESCRIPTION 13 FT. 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT. COMPLETE SICKLE (OEM) 24012 24015 24019 24020 24023 24026



PARTS LISTS

NOTE: DOUBLE POINT SICKLES ARE NOT COMPATIBLE WITH BEARCUT SYSTEMS.

CASE IH COMBINESHEADER: 810 RIGID OR W/HINIKER FLOATING CUTTERBAR

DESCRIPTION 10 FT. 13 FT. 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT. 24 FT. 30 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 19900 19901 19715 19902 19716 19717 19903 19718 19694

COMPLETE SICKLE 19892 19893 19311 19894 19433 19434 19895 19435 19436-LEFT HAND SICKLE 28131 28131 28131 28131 28131 28131 28131 28131 28131

-CENTER SICKLE - - - - - 28132 28132 28132 28132 (2)-RIGHT HAND SICKLE 28140 28138 28136 28134 28133 28139 28137 28135 28138

PART # DESCRIPTION QTY QTY QTY QTY QTY QTY QTY QTY QTY

7226 GUARD, GOLD 20 26 30 33 35 40 45 48 6017200 SECTION, GOLD 35 47 55 61 65 75 85 91 11529027 SECTION, HALF-HEAD 1 1 1 1 1 1 1 1 121556 SECTION, HALF-RH 1 1 1 1 1 1 1 1 129029 SECTION, HEAD 3 3 3 3 3 3 3 3 3

24337 HOLD DOWN (SPRING LOADED) 9 12 14 15 16 19 21 23 29

24911 HOLD DOWN (SPRING LOAD-ED HEAD) 1 1 1 1 1 1 1 1 1

15058 BOLT, 3/8 X 1/2” CARRIAGE 20 26 30 32 34 40 44 48 6015378 BOLT, 3/8 X 1-1/4” CARRIAGE 20 26 30 34 36 40 46 48 6015051 NUT, 3/8” SERR. FLANGE 40 52 60 66 70 80 90 96 120

DESCRIPTION 10 FT. 13 FT. 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT. 24 FT. 30 FT. DOUBLE POINT SICKLE 19896 19897 19529 19898 19530 19531 19899 19532 19533

-LEFT HAND SICKLE 28141 28141 28141 28141 28141 28141 28141 28141 28141-CENTER SICKLE 28142 28142 28142 28142-RIGHT HAND SICKLE 28150 28148 28146 28144 28143 28149 28147 28145 28148


PARTS LISTS

NOTE: DOUBLE POINT SICKLES ARE NOT COMPATIBLE WITH BEARCUT OR KINGKUT SYSTEMS.

CASE IH COMBINESHEADER: 820 FLEX

DESCRIPTION 13 FT. 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 19548 19456 19549 19457 19458 19550 COMPLETE SICKLE 19541 19448 19542 19449 19450 19543

-LEFT HAND SICKLE 28151 28151 28151 28151 28151 28151-CENTER SICKLE - - - - 28152 28152-RIGHT HAND SICKLE 28157 28155 28154 28153 28158 28156

KINGKUT COMPLETE SYSTEM (KK) 27321 27322 27323 27324 27325 27326 COMPLETE SICKLE 27315 27316 27317 27318 27319 27320

-LEFT HAND SICKLE 27065-00 27065-00 27065-00 27065-00 27065-00 27065-00-CENTER SICKLE - - - - 27071-00 27071-00-RIGHT HAND SICKLE 27084-00 27085-00 27076-00 27086-00 27083-00 27080-00

PART # DESCRIPTION QTY QTY QTY QTY QTY QTY7229 GUARD, GOLD 22 26 29 31 36 4122063 GUARD, HEAD 3 3 3 3 3 324361 GUARD, END 1 1 1 1 1 117201 SECTION, GOLD (BC) 47 55 61 65 75 8514765 SECTION, KINGKUT (KK) 47 55 61 65 75 8529028 SECTION, HALF-HEAD 1 1 1 1 1 129030 SECTION, HEAD (BC) 3 3 3 3 3 327066-00 SECTION, KINGKUT HEAD-LH (KK) 3 3 3 3 3 324335 HOLD DOWN (SPRING LOADED) 12 14 15 17 19 2124911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 1 1 117329 WEAR PLATE (6”) 13 15 16 17 20 2222523 SHIM (.010) 13 15 16 17 20 2222524 SHIM (.024) 13 15 16 17 20 2215241 BOLT, 7/16 X 1-1/2” CARRIAGE 25 29 33 35 39 4515061 BOLT, 7/16 X 1-3/4” CARRIAGE 26 30 32 34 40 4415052 NUT, 7/16” SERR. FLANGE 51 59 65 69 79 89

DESCRIPTION 13 FT. 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT. DOUBLE POINT SICKLE 19544 19453 19545 19454 19455 19546

-LEFT HAND SICKLE 28159 28159 28159 28159 28159 28159-CENTER SICKLE 28160 28160-RIGHT HAND SICKLE 28165 28163 28162 28161 28166 28164


PARTS LISTS

NOTE: DOUBLE POINT SICKLES ARE NOT COMPATIBLE WITH GOLD’N CUT OR KINGKUT SYSTEMS.

CASE IH COMBINESHEADER: 1010 RIGID (3” SICKLE)

DESCRIPTION 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT. 25 FT. 30 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 28885 28886 28887 28888 28889 28890 COMPLETE SICKLE 19909 19910 19911 19912 19913 19914 19915

-LEFT HAND SICKLE 28167 28167 28167 28167 28167 28167 28167

-CENTER SICKLE - - 28152 28152 28152 28152 (2)-RIGHT HAND SICKLE 28171 28170 28169 28174 28172 28170 28173

KINGKUT COMPLETE SYSTEM (KK) 27334 27335 27336 27337 27338 27339 COMPLETE SICKLE 27327 27329 27330 27331 27332 27333

-LEFT HAND SICKLE 27067-00 27067-00 27067-00 27067-00 27067-00 27067-00

-CENTER SICKLE - - 27071-00 27071-00 27071-00 27071-00 (2)-RIGHT HAND SICKLE 27102-00 27103-00 27100-00 27092-00 27096-00 27101-00

PART # DESCRIPTION QTY QTY QTY QTY QTY QTY QTY7229 GUARD, GOLD 26 32 36 42 46 5622063 GUARD, HEAD 3 3 3 3 3 317201 SECTION, GOLD (BC) 59 69 79 89 99 11914765 SECTION, KINGKUT (KK) 58 68 78 88 98 11822526 SECTION, HALF-LH 1 1 1 1 1 117339 SECTION, H & S END-RH (BC) 1 1 1 1 1 124335 HOLD DOWN (SPRING LOADED) 14 17 19 22 24 2924911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 1 1 117329 WEAR PLATE (6”) 15 18 20 23 25 3022523 SHIM (.010) 30 36 40 46 50 6021256 SHIM (.036) 15 18 20 23 25 3021592 SHIM (.105) 15 18 20 23 25 3015061 BOLT, 7/16 X 1-3/4” CARRIAGE 30 36 40 46 50 6015241 BOLT, 7/16 X 1-1/2” CARRIAGE 28 34 38 44 48 5815052 NUT, 7/16” SERR. FLANGE 58 70 78 90 98 118

HEADER: 1010 RIGID (3” SICKLE) AND 1020 FLEXDESCRIPTION 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT. 25 FT. 30 FT.

DOUBLE POINT SICKLE 28342 28343 28344 28345 28346 28347 28348-LEFT HAND SICKLE 28365 28365 28365 28365 28365 28365 28365-CENTER SICKLE 28366 28366 28366 28366-RIGHT HAND SICKLE 28369 28368 28367 28372 28370 28368 28371


PARTS LISTS

CASE IH COMBINESHEADER: 1020 FLEXNOTE: WHEN REPLACING A 1-1/2” SYSTEM WITH A 3” SYSTEM, IT IS NECESSARY TO USE A SICKLE HEAD FOR A 3” SYSTEM.

DESCRIPTION 15 FT. 16.5 FT. 17.5 FT. 20 FT. 22.5 FT. 25 FT. 30 FT.GOLD’N CUT COMPLETE SYSTEM (BC) (7228) 25455 25456 25457 25458 25459 25460 25461GOLD’N CUT COMPLETE SYSTEM (BC) (7229) 19925 19926 19927 19928 19929 19930 19931 COMPLETE SICKLE (7228) (7229) 19909 19910 19911 19912 19913 19914 19915

-LEFT HAND SICKLE (8.5 FT.) 28167 28167 28167 28167 28167 28167 28167-CENTER SICKLE (8.5 FT.) - - - 28152 28152 28152 28152(2)-RIGHT HAND SICKLE 28171 28170 28169 28174 28172 28170 28173

KINGKUT COMPLETE SYSTEM (KK) (7228) 27340 27341 27342 27343 27344 27345 27346KINGKUT COMPLETE SYSTEM (KK) (7229) 27347 27348 27349 27350 27351 27352 27353 COMPLETE SICKLE 27327 27328 27329 27330 27331 27332 27333

-LEFT HAND SICKLE (8.5 FT.) 27067-00 27067-00 27067-00 27067-00 27067-00 27067-00 27067-00

-CENTER SICKLE (8.5 FT.) - - - 27071-00 27071-00 27071-00 27071-00 (2)-RIGHT HAND SICKLE 27102-00 27096-00 27103-00 27100-00 27092-00 27096-00 27101-00

PART # DESCRIPTION QTY QTY QTY QTY QTY QTY QTY7228 GUARD, GOLD 26 30 32 36 42 46 567229 GUARD, GOLD 26 30 32 36 42 46 5622063 GUARD, HEAD 3 3 3 3 3 3 324361 GUARD, END 2 - - 2 - 2 217201 SECTION, GOLD (BC) 59 65 69 79 89 99 11914765 SECTION, KINGKUT (KK) 58 64 68 78 88 98 11822526 SECTION, HALF-LH 1 1 1 1 1 1 117339 SECTION, H & S END-RH 1 1 1 1 1 1 124338 HOLD DOWN (SPRING LOADED) (7228) 14 15 16 19 21 24 29

25454 HOLD DOWN (SPRING LOADED HEAD) (7228) 1 1 1 1 1 1 1

25615 HOLD DOWN (SPRING LOADED) (7229) 14 15 16 19 21 24 29

25348 HOLD DOWN (SPRING LOADED HEAD) (7229) 1 1 1 1 1 1 1

17329 WEAR PLATE (6”) (7229) 15 17 18 19 23 24 2924261 WEAR PLATE, OFFSET (6”) (7229) 15 16 17 20 22 25 3022524 SHIM (.024) (7229) 15 17 18 19 23 24 2921256 SHIM (.036) (7229) 15 17 18 19 23 24 2922523 SHIM (.010) (7228) 15 17 18 20 23 25 3022523 SHIM (.010) (7229) 30 33 35 39 45 49 5915061 BOLT, 7/16 X 1-3/4” CARRIAGE 30 32 34 40 44 50 6015241 BOLT, 7/16 X 1-1/2” CARRIAGE 28 32 34 38 44 48 5815082 BOLT, 7/16 X 2” CARRIAGE 2 2 2 2 2 2 215052 NUT, 7/16” SERR. FLANGE 60 66 70 80 90 100 120


PARTS LISTS

CASE IH HAY MACHINESHEADER: 1100, 1300, SERIES 100 BALANCED HEADMOWER: ALL MOWERSMOWER/CONDITIONER: 990

DESCRIPTION 5 FT. 6 FT. 7 FT. 9 FT. 7 FT. (990)9 FT. (990)

GOLD’N CUT COMPLETE SYSTEM (TS) 19668 19670 19671 19672 19662 19664 COMPLETE SICKLE 19667 19669 28433 28434 19665 19663

-LEFT HAND SICKLE 19667 19669 28433 28100 19665 28241-LH END SICKLE - - - 28102 - 28104

GOLD’N CUT COMPLETE SYSTEM (US) 28056 28057 28058 28059 28480 28481 COMPLETE SICKLE 28017 28016 28014 28055 28478 28479

-LEFT HAND SICKLE 28017 28016 28014 28101 28478 28483-LH END SICKLE - - - 28103 - 28484

PART # DESCRIPTION QTY QTY QTY QTY QTY QTY7228 GUARD, GOLD 6 8 10 14 11 1522063 GUARD, HEAD 3 3 3 3 3 322659 GUARD, SINGLE POINT 1 1 1 1 1 117367 SECTION, GOLD (TS) 19 23 27 34 27 3517368 SECTION, GOLD (US) 19 23 27 34 27 3522836 SECTION, HALF-LH (TS) - - - - 1 122837 SECTION, HALF-LH (US) - - - - 1 117339 SECTION, H & S END-RH (TS) 1 1 1 1 1 117884 SECTION, H & S END-RH (US) 1 1 1 1 1 124338 HOLD DOWN (SPRING LOADED) 4 5 6 8 6 824911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 1 1 122523 SHIM (.010) 5 6 7 9 - -22524 SHIM (.024) 5 6 7 9 - -15061 BOLT, 7/16 X 1-3/4” CARRIAGE 10 12 14 18 14 1815241 BOLT, 7/16 X 1-1/2” CARRIAGE 9 11 13 17 14 1815052 NUT, 7/16” SERR. FLANGE 19 23 27 35 28 36


PARTS LISTS

CASE IH HAY MACHINESMOWER/CONDITIONER: 8840, 8870, 8830 W/625 HEADER HEADER: 425 HEADER, SC 414 & 416, 8820 SINGLE AUGER HEADER

DESCRIPTION 21 FT. 25 FT. 30 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 25545 25546 25547 COMPLETE SICKLE 24807 24808 24809

-LEFT HAND SICKLE (8.5 FT.) 24811 24811 24811-LH END SICKLE 24817 24815 24813-RIGHT HAND SICKLE (8.5 FT.) 24812 24812 24812-RH END SICKLE 24818 24816 24814

GOLD’N CUT COMPLETE SYSTEM (TS) 24409 24410 24411 COMPLETE SICKLE 24406 24407 24408

-LEFT HAND SICKLE (8.5 FT.) 24390 24390 24390-LH END SICKLE 24391 24392 24393-RIGHT HAND SICKLE (8.5 FT.) 24394 24394 24394-RH END SICKLE 24395 24396 24397

GOLD’N CUT COMPLETE SYSTEM (US) 24415 24416 24417 COMPLETE SICKLE 24412 24413 24414

-LEFT HAND SICKLE 24398 24398 24398-LH END SICKLE 24399 24400 24401-RIGHT HAND SICKLE (8.5 FT.) 24402 24402 24402-RH END SICKLE 24403 24404 24405PART # DESCRIPTION QTY QTY QTY

7228 GUARD, GOLD 40 48 5822847 GUARD, CENTER 2 2 213454-00 GUARD, SINGLE POINT 1 1 117201 SECTION, GOLD (BC) 79 95 11517367 SECTION, GOLD (TS) 76 92 11217368 SECTION, GOLD (US) 76 92 11217420 SECTION, GOLD (BOTTOM CSK) 3 3 317349 SECTION, H & S END-LH (TS) 1 1 117339 SECTION, H & S END-RH (TS) 1 1 117884 SECTION, H & S END-RH (US) 1 1 116009 SECTION, OVERLAP 3 3 324338 HOLD DOWN (SPRING LOADED) 18 22 2724911 HOLD DOWN (SPRING LOADED HEAD) 3 3 328974 OVERLAP STRAP 1 1 122523 SHIM (.010) 21 25 3022524 SHIM (.024) 21 25 3015061 BOLT, 7/16 X 1-3/4” CARRIAGE 42 50 6015241 BOLT, 7/16 X 1-1/2” CARRIAGE 42 50 6015684-00 BOLT, 7/16 X 20 X 1 GR 5 HCPS 2 2 215052 NUT, 7/16” SERR. FLANGE 84 100 120


PARTS LISTS

CASE IH HAY MACHINESSWATHER: 8200 & 8220 (PULL TYPE)

DESCRIPTION 21 FT. 25 FT. 30 FT. 35 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 25541 25542 25543 25544 COMPLETE SICKLE 24717 24718 24719 24720

-LEFT HAND SICKLE 24721 24721 24721 24721-CENTER SICKLE 24660 24660 24660 (2) 24660 (3)-RIGHT HAND SICKLE 24713 24722 24723 24724

GOLD’N CUT COMPLETE SYSTEM (TS) 24377 24378 24379 24380 COMPLETE SICKLE 24373 24374 24375 24376

-LEFT HAND SICKLE 24371 24371 24371 24371-CENTER SICKLE 28106 28106 28106 (2) 28106 (3)-RIGHT HAND SICKLE 24480 28998 29000 28712

GOLD’N CUT COMPLETE SYSTEM (US) 24386 24387 24388 24389 COMPLETE SICKLE 24382 24383 24384 24385

-LEFT HAND SICKLE 24381 24381 24381 24381-CENTER SICKLE 28500 28500 28500 (2) 28500 (3)-RIGHT HAND SICKLE 24481 28999 29001 28750PART # DESCRIPTION QTY QTY QTY QTY

7228 GUARD, GOLD 42 50 60 7013454-00 GUARD, SINGLE POINT 1 1 1 117201 SECTION, GOLD (BC) 84 100 120 14017367 SECTION, GOLD (TS) 84 100 120 14017368 SECTION, GOLD (US) 84 100 120 14017349 SECTION, H & S END-LH (TS) 1 1 1 117884 SECTION, H & S END-RH (US) 1 1 1 124338 HOLD DOWN (SPRING LOADED) 20 24 29 3424911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 122523 SHIM (.010) 21 25 30 3522524 SHIM (.024) 21 25 30 3515061 BOLT, 7/16 X 1-3/4” CARRIAGE 42 50 60 7015241 BOLT, 7/16 X 1-1/2” CARRIAGE 42 50 60 7015684-00 BOLT, 7/16 X 20 X 1 GR 5 HCPS 2 2 2 215052 NUT, 7/16” SERR. FLANGE 84 100 120 140


PARTS LISTS

CASE IH HAY MACHINESMOWER/CONDITIONER: 1190 (7’ & 9’) & 1590 (9’)WINDROWER: 230, 4000, 5000 W/SINGLE AUGER OR DRAPER HEADER (12’-24’), 210 AFTER SN 3700

DESCRIPTION 7 FT. 9 FT. 12.5 FT. 14.5 FT. 16.5 FT. 19.5 FT. 24.5 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 25517 25518 25519 25520 25521 25522 25523 COMPLETE SICKLE 24728 24729 24730 24731 24732 24733 24734

-LEFT HAND SICKLE 24728 24735 24735 24735 24735 24735 24735-CENTER SICKLE - - - - - 24660 24660-RIGHT HAND SICKLE - 24677 24686 24687 24688 24736 24737

GOLD’N CUT COMPLETE SYSTEM (TS) 19648 19649 19653 19655 19657 19812 19814 COMPLETE SICKLE 19615 19619 19652 19654 19656 19811 19813

-LEFT HAND SICKLE 19615 28105 28105 28105 28105 28105 28105-CENTER SICKLE - - - - - 28106 28106-RIGHT HAND SICKLE - 28112 28110 28109 28107 28111 28108

GOLD’N CUT COMPLETE SYSTEM (US) 28486 28488 28490 28492 28494 28496 28498 COMPLETE SICKLE 28485 28487 28489 28491 28493 28495 28497

-LEFT HAND SICKLE 28485 28499 28499 28499 28499 28499 28499-CENTER SICKLE - - - - - 28500 28500-RIGHT HAND SICKLE - 28507 28505 28504 28501 28506 28502PART # DESCRIPTION QTY QTY QTY QTY QTY QTY QTY

7228 GUARD, GOLD 11 15 21 25 29 35 4522063 GUARD, HEAD 3 3 3 3 3 3 322659 GUARD, SINGLE POINT 1 1 1 1 1 1 117201 SECTION, GOLD (BC) 24 32 44 52 60 72 9217367 SECTION, GOLD (TS) 24 32 44 52 60 72 9217368 SECTION, GOLD (US) 24 32 44 52 60 72 9229030 SECTION, HEAD (BC) 4 4 4 4 4 4 424746 SECTION, HEAD (TS) 4 4 4 4 4 4 424745 SECTION, HEAD (US) 4 4 4 4 4 4 417339 SECTION, H & S END-RH (TS) 1 1 1 1 1 1 117884 SECTION, H & S END-RH (US) 1 1 1 1 1 1 124338 HOLD DOWN (SPRING LOADED) 4 6 9 11 13 16 2124911 HOLD DOWN (SPRING LOADED HEAD) 2 2 2 2 2 2 222523 SHIM (.010) 6 8 11 13 15 18 2322524 SHIM (.024) 6 8 11 13 15 18 2321842 SHIM (3/16) 21 21 21 21 21 21 2115061 BOLT, 7/16 X 1-3/4” CARRIAGE 12 16 22 26 30 36 4615241 BOLT, 7/16 X 1-1/2” CARRIAGE 17 21 27 31 35 41 5115052 NUT, 7/16” SERR. FLANGE 29 37 49 57 65 77 97


PARTS LISTS

CASE IH HAY MACHINESMOWER: 8320 (7’), 8330 & 8340 (9’), 8350 & 8360 (12’), 8370 (14’), 8830 (12’ & 14’)

DESCRIPTION 7 FT. 9 FT. 12 FT. 14 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 25503 25504 25505 25506 COMPLETE SICKLE 24689 24690 24691 24692

-LEFT HAND SICKLE 24689 24693 24693 24693-RIGHT HAND SICKLE - 24694 24695 24696

GOLD’N CUT COMPLETE SYSTEM (TS) 28003 28004 28005 28374 COMPLETE SICKLE 28000 28001 28002 28373

-LEFT HAND SICKLE 28000 28437 28437 28437-RIGHT HAND SICKLE - 28439 28438 28375

GOLD’N CUT COMPLETE SYSTEM (US) 28576 28578 28580 28582 COMPLETE SICKLE 28575 28577 28579 28581

-LEFT HAND SICKLE 28575 28583 28583 28583-RIGHT HAND SICKLE - 28103 28584 28586PART # DESCRIPTION QTY QTY QTY QTY

7228 GUARD, GOLD 15 19 25 2913454-00 GUARD, SINGLE POINT 1 1 1 117201 SECTION, GOLD (BC) 27 35 47 5417367 SECTION, GOLD (TS) 27 35 47 5417368 SECTION, GOLD (US) 27 35 47 5417349 SECTION, H & S END-LH (TS) 1 1 1 117339 SECTION, H & S END-RH (TS) 1 1 1 117884 SECTION, H & S END-RH (US) 1 1 1 124338 HOLD DOWN (SPRING LOADED) 6 8 11 1324911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 122523 SHIM (.010) 7 9 12 1422524 SHIM (.024) 7 9 12 1415061 BOLT, 7/16 X 1-3/4” CARRIAGE 14 18 24 2815241 BOLT, 7/16 X 1-1/2” CARRIAGE 16 20 26 3015684-00 BOLT, 7/16 X 20 X 1 GR 5 HCPS 2 2 2 215052 NUT, 7/16” SERR. FLANGE 30 38 50 58


PARTS LISTS

CASE IH HAY MACHINESMOWER/CONDITIONER: 8840, 8870, 8380 WITH 625 HEADER, SC 414 & 416

DESCRIPTION 14 FT. 16 FT. 18 FT.GOLD’N CUT COMPLETE SYSTEM (TS) 28986 28984 27050 COMPLETE SICKLE 28982 28980 27052

-LEFT HAND SICKLE 29021 29019 27022-00-LEFT END SICKLE 28253-RIGHT HAND SICKLE 28978 28976 27021-00-RIGHT END SICKLE 24395

GOLD’N CUT COMPLETE SYSTEM (US) 28987 28985 27051 COMPLETE SICKLE 28983 28981 27053

-LEFT HAND SICKLE 29022 29020 27023-00-LEFT END SICKLE 27024-00-RIGHT HAND SICKLE 28979 28977 28253-RIGHT END SICKLE 24403PART # DESCRIPTION QTY QTY QTY

7228 GUARD, GOLD 26 30 3422847 GUARD, CENTER 2 2 213454-00 GUARD, SINGLE POINT 1 1 117367 SECTION, GOLD (TS) 50 58 6617368 SECTION, GOLD (US) 50 58 6617420 SECTION, GOLD (BOTTOM CSK) 3 3 317349 SECTION, H & S END-LH (TS) 1 1 117339 SECTION, H & S END-RH (TS) 1 1 117884 SECTION, H & S END-RH (US) 1 1 116009 SECTION, OVERLAP 2 2 224338 HOLD DOWN (SPRING LOADED) 6 7 825615 HOLD DOWN (SPRING LOADED) 7 8 924911 HOLD DOWN (SPRING LOADED HEAD) 2 2 217427 SPACER 1 1 128974 OVERLAP STRAP 1 1 122523 SHIM (.010) 15 17 1922524 SHIM (.024) 15 17 1915061 BOLT, 7/16 X 1-3/4” CARRIAGE 30 34 3815241 BOLT, 7/16 X 1-1/2” CARRIAGE 26 30 3415684-00 BOLT, 7/16 X 20 X 1 GR 5 HCPS 2 2 215052 NUT, 7/16” SERR. FLANGE 56 64 72


PARTS LISTS

CASE IH HAY MACHINESMOWER/CONDITIONER: CIH1490 (12’), 1590 (14’); NEW IDEA 512, 5112 (12’), 514, 5114 (14’)WINDROWER: 4000, 5000, 5500 W/DUAL AUGER HEADER

DESCRIPTION4000, 5000, 5500 CIH 1490, 1590 NEW IDEA 512, 5112, 514, 5114

12 FT. 14 FT. 16 FT. 12 FT. 14 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 25524 25525 25526 25527 25528 COMPLETE SICKLE 24738 24739 24740 24741 24742

-LEFT HAND SICKLE 24749 24749 24749 24749 24749-RIGHT HAND SICKLE 24695 24743 24744 24686 24687

GOLD’N CUT COMPLETE SYSTEM (TS) 28410 28411 28412 28467 28468 COMPLETE SICKLE 28407 28408 28409 28465 28466


GOLD’N CUT COMPLETE SYSTEM (US) 28513 28514 28515 28516 28517 COMPLETE SICKLE 28508 28509 28510 28511 28512


PART # DESCRIPTION QTY QTY QTY QTY QTY7228 GUARD, GOLD 21 25 29 21 2522063 GUARD, HEAD 3 3 3 3 322659 GUARD, SINGLE POINT 1 1 1 1 117201 SECTION, GOLD (BC) 43 51 59 44 5217367 SECTION, GOLD (TS) 43 51 59 44 5217368 SECTION, GOLD (US) 43 51 59 44 5222526 SECTION, HALF-LH (BC) 1 1 1 1 122836 SECTION, HALF-LH (TS) 1 1 1 1 122837 SECTION, HALF-LH (US) 1 1 1 1 129030 SECTION, HEAD (BC) 4 4 4 4 424746 SECTION, HEAD (TS) 4 4 4 4 424745 SECTION, HEAD (US) 4 4 4 4 417339 SECTION, H & S END-RH (TS) 1 1 1 1 117884 SECTION, H & S END-RH (US) 1 1 1 1 124338 HOLD DOWN (SPRING LOADED) 10 12 14 10 12

24911 HOLD DOWN (SPRING LOADED HEAD) 2 2 2 2 2

15061 BOLT, 7/16 X 1-3/4” CARRIAGE 24 28 32 24 2815241 BOLT, 7/16 X 1-1/2” CARRIAGE 25 29 33 25 2915052 NUT, 7/16” SERR. FLANGE 49 57 65 49 57


PARTS LISTS

CASE IH HAY MACHINESWINDROWER: CASE-IH 721, 725, 730, 736, 742, 750, 6000, 6500

DESCRIPTION 12 FT. 14 FT. 15 FT. 16 FT. 18 FT. 21 FT. 25 FT. 30 FT. 36 FT.GOLD’N CUT COMPLETE SYSTEM (BC) 23961 23962 23963 23964 23965 23966 23967 23968 23969

COMPLETE SICKLE 23970 23971 23972 29562 23974 23975 23976 23977 23978-LEFT HAND SICKLE (8.5 FT.) 23950 24986 23950 24986 23950 23950 23950 23950 23950

-CENTER SICKLE - - - - 23951 23951 23951 23951 (2)23951

(3)

-RIGHT HAND SICKLE (8.5 FT.) 29396-0029378-

0029381-

0029384-

0029387-

0029375-

0029384-

0023390-

0029393-

00GOLD’N CUT COMPLETE SYSTEM (TS) 28945 28946 28947 28948 28949 28950 28951 28952 28964

COMPLETE SICKLE 28945 28930 28931 29563 28933 28934 28935 28936 28953

-LEFT HAND SICKLE (8.5 FT.) 28908 29430-00 2890829430-

00 28908 28908 28908 28908 28908

-CENTER SICKLE - - - - 28909 28909 28909 28909 (2)28909

(3)

-RIGHT HAND SICKLE 28911 29379-0029382-

0029385-

0029388-

0029375-

0029385-

0029391-

0029394-

00GOLD’N CUT COMPLETE SYSTEM (US) 28953 28954 28955 28956 28957 28958 28959 28960 28967

COMPLETE SICKLE 28937 28938 28939 29564 28941 28942 28943 28944 28965

-LEFT HAND SICKLE 28919 29431-00 2891929431-

00 28919 28919 28919 28919 28919

-CENTER SICKLE - - - - 28920 28920 28920 28920 (2)28920

(3)

-RIGHT HAND SICKLE (8.5 FT.) 29398-0029380-

0029383-

0029386-

0029389-

0029377-

0029386-

0029392-

0029395-

00PART # DESCRIPTION QTY QTY QTY QTY QTY QTY QTY QTY QTY

7228 GUARD, GOLD 23 27 28 31 34 40 48 58 7022063 GUARD, HEAD 2 2 2 2 3 3 3 3 316918 SECTION, GOLD (BC) 48 56 58 64 70 83 99 118 14217877 SECTION, GOLD (TS) 48 56 58 64 70 83 99 118 14217878 SECTION, GOLD (US) 48 56 58 64 70 83 99 118 14223949 SECTION, HALF-LH (BC) 1 1 1 1 1 1 1 1 122786 SECTION, HALF-LH (US) 1 1 1 1 1 1 1 1 1

17339 SECTION, H & S END-RH (TS) 1 1 1 1 1 1 1 1 1

17884 SECTION, H & S END-RH (US) 1 1 1 1 1 1 1 1 1

24338 HOLD DOWN (SPRING LOADED) 11 13 14 15 17 20 24 29 35

24911 HOLD DOWN (SPRING LOADED HEAD) 1 1 1 1 1 1 1 1 1

22523 SHIM (.010) 12 14 15 16 18 21 25 30 3621256 SHIM (.036) 24 28 30 32 36 42 50 60 72

15082 BOLT, 7/16 X 2” CAR-RIAGE 24 28 60 32 36 42 50 60 72

15241 BOLT, 7/16 X 1-1/2”CAR-RIAGE 26 30 60 34 36 44 50 60 72

15052 NUT, 7/16” SERR. FLANGE 50 58 60 66 72 86 100 120 144


PARTS LISTS

NEW HOLLAND COMBINESHEADER: 960 RIGID

DESCRIPTION 11 FT. 13 FT. 15 FT. 17 FT. 19 FT. 20 FT. 22 FT. GOLD’N CUT COMPLETE SYSTEM (BC) 19784 19786 19788 19790 19792 19794 19796 COMPLETE SICKLE 19798 19800 19774 19776 19778 19780 19782

-LEFT HAND SICKLE 28211 28211 28211 28211 28211 28211 28211-CENTER SICKLE - - - - 28212 28212 28212-RIGHT HAND SICKLE 28302 28300 28298 28297 28303 28301 28299

KINGKUT COMPLETE SYSTEM (KK) 27420 28421 27422 27423 27424 27425 27426 COMPLETE SICKLE 27414 27415 27382 27416 27417 27418 27419

-LEFT HAND SICKLE 27070-00 27070-00 27070-00 27070-00 27070-00 27070-00 27070-00-CENTER SICKLE - - - - 27071-00 27071-00 27071-00-RIGHT HAND SICKLE 27100-00 27091-00 27093-00 27103-00 27105-00 27089-00 27092-00PART # DESCRIPTION QTY QTY QTY QTY QTY QTY QTY

7222 GUARD, GOLD 23 27 31 35 39 41 4517203 SECTION, GOLD (BC) 44 52 60 68 76 80 8814765 SECTION, KINGKUT (KK) 43 51 59 67 75 79 8721553 SECTION,

crary cutting systems owner’s manual case ih -...

Documents