craftsman table saw
TRANSCRIPT
Save This ManualFor Future Reference
MODEL NO.113.221611
SerialNumber
Model and serial
number may be foundat the rear of the base,,
You should record both
model and serial number
in a safe place forfuture use,
CAUTION:
READ ALL
INSTRUCTIONSCAREFULLY
8 INCH DIRECT DRIVETABLE SA W
o assembly
® operating
o repair parts
Sold by SEARS, ROEBUCK AND CO,, Chicago, IL 60684 U.S.A.Part No, SP5022 Primed i_ U S A
FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW
If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect inmaterial or workmanship, Sears will repair it, free of chargeWARRANTY SERVICE IS AVAILABLE BY RETURNING THE TABLE SAW TO THE NEARESTSEARS RETAIL/CATALOG STORE OR SERVICE CENTER/DEPARTMENT IN THE UNITEDSTATES
This warranty gives you specific legal rights and you may also have other rights which varyfrom state to state,
SEARS, ROEBUCK AND CO,,, Scars Tower, BSC 4%3, Chicago, iL 60684
GENERAL SAFETY iNSTRUCTiONSFOR POWER TOOLS
1. KNOW YOUR POWER TOOLRead and understand the owner's manual andlabels affixed to the tool Learn its applicationand limitations as well as the specific potentialhazards peculiar to this tool
2. GROUND ALL TOOLSThis tool is equipped with an approved 3-conductor cord and a 3-prong grounding typeplug to fit the propergrounding type receptacle,The green conductor in the cord is thegrounding wire° Never connect the green wire toa live terminal
3. KEEP GUARDS IN PLACEIn working order, and in proper adjustment andalignment.
4. REMOVE ADJUSTING KEYSAND WRENCHESForm habit of checking to see that keys andadjusting wrenches are removed from toolbefore turning it on.
5. KEEP WORK AREA CLEANCluttered areas and benches invite accidents.,Floor must not be siippery due to wax orsawdust.
6, AVOID DANGEROUS ENVIRONMENTDon't use power tools in damp or wet locationsor expose them to rain. Keep work area welllighted Provide adequate surrounding workspace..
7, KEEP CHILDREN AWAYAll visitors should be kept a safe distance fromwork area,
8. MAKE WORKSHOP CHILD-PROOF-- with padlocks, master switches, or byremoving starter keys.
9. DON'T FORCE TOOLIt wit! do the job better and safer at the rate forwhich it was designed
10. USE RIGHT TOOLDon't force tool or attachment to do a job it wasnot designed for.
11. WEAR PROPER APPARELDo not wear loose clothing, gloves, neckties orjewelry (rings, wrist watches) to get caught inmoving parts, Nonslip footwear isrecommended Wear protective hair covering tocontain tong hair Roll long sleeves above theelbow
12. USE SAFETY GOGGLES (Head Protection)Wear Safety goggles (must comply with ANSI
Z87.,1) at all times° Everyday eyeglasses onlyhave impact resistant lenses, they are NOTsafety glasses. Also, use face or dust mask ifcutting operation is dusty, and ear protectors(plugs or muffs) during extended periods ofoperation.
13. SECURE WORKUse clamps or a vise to hold work whenpractical It's safer than using your hand, freesboth hands to operate tool
14. DON'T OVERREACHKeep proper footing and balance at all times,
15. MAINTAIN TOOLS WITH CAREKeep tools sharp and clean for best and safestperformance,, Follow instructions for lubricatingand changing accessories,
16. DISCONNECT TOOLSBefore servicing; when changing accessoriessuch as blades, bits, cutters, etc
17_ AVOID ACCIDENTAL STARTINGMake sure switch is in "OFF" position beforeplugging in,
18. USE RECOMMENDED ACCESSORIESConsult the owner's manual for recommendedaccessories, Follow the instructions thataccompany the accessories_ The use ofimproper accessories may cause hazards.
19. NEVER STAND ON TOOLSerious injury could occur if the tool istipped orif the cutting tool is accidentally contacted,
Do not store materials above or near the tootsuch that it is necessary to stand on the tool toreach them
20. CHECK DAMAGED PARTSBefore further use of the tool, a guard or otherpart that is damaged should be carefullychecked to ensure that it will operate properlyand perform its intended function., Check foralignment of moving parts, binding of movingparts, breakage of parts, mounting, and anyother conditions that may affect its operation. Aguard or other part that is damaged should beproperly repaired or replaced
21. DIRECTION OF FEEDFeed work into a blade or cutter against thedirection of rotation of the blade or cutter only
22. NEVER LEAVE TOOL RUNNINGUNATTENDEDTurn power off Don't leave tool until it comes toa complete stop,
ADDITIONAL SAFETYFOR TABLE
WARNING: FOR YOUR OWN SAFETY, DO NOTOPERATE YOUR SAW UNTIL IT IS COMPLETELYASSEMBLED AND INSTALLED ACCORDING TOTHE INSTRUCTIONS,.. AND UNTIL YOU HAVEREAD AND UNDERSTAND THE FOLLOWING:1. GENERAL SAFETY INSTRUCTIONS FOR
POWER TOOLS. _. SEE PAGE 22, GETTING TO KNOW YOUR SAW.,, SEE PAGE
2O3. BASIC SAW OPERATION _., SEE PAGE 234. MAINTENANCE ._. SEE PAGE 315. STABILITY OF SAW
if there is any tendency for the saw to tip over ormove during certain cutting operations such ascutting extremely large heavy panels or longheavy boards, the saw should be bolted down.If you attach any kind of auxiliary tableextensions over 24" wide to either end of the saw,make sure you either bolt the saw to the bench orfloor as appropriate, or support the outer end ofthe extension from the bench or floor, asappropriate,
6. LOCATIONThe saw should be positioned so neither theoperator nor a casual observer is forced to standin line with the saw biade,
7. KICKBACKSA "KICKBACK" occurs during a rip-typeoperation when a part or all of the workpiece isviolently thrown back toward the operatorKeep your face and body to one side of thesawblade, out of line with a possible "Kickback."Kickbacks -- and possible injury from them --can usually be avoided by:A Maintaining the rip fence parallel to the
sawblade,B Keeping the sawblade sharp Replace or
sharpen antikickback pawls when pointsbecome dull
C. Keeping sawblade guard, spreader, andantikickback pawls in place and operatingproperly The spreader must be in alignmentwith the sawblade and the pawls must stop akickback once it has started. Check theiraction before ripping
D, NOT ripping work that is twisted or warped ordoes not have a straight edge to guide alongthe rip fence
E NOT releasing work until you have pushed itall the way past the sawblade.
F. Using a push stick for ripping widths of 2 to 6in., and an auxiliary fence and push block forripping widths narrower than 2 in. (See "BasicSaw Operation Using The Rip Fence"section )
G NOT confining the cut-off piece when rippingor cross-cutting
H When ripping apply the feed force to thesection of the workpiece between the sawblade and the rip fence.
8. PROTECTION: EYES, HANDS, FACE, EARS,BODYA if any part of your saw is malfunctioning, has
INSTRUCTIONSSAWS
B
C
D,
E
F
been damaged or broken ...such as the motorswitch, or other operating control, a safetydevice or the power cord. cease operatingimmediately until the particular part isproperly repaired or replacedWear safety goggles that comply with ANSIZ87.1, and a face shield if operation is dusty.Wear ear plugs or muffs during extendedperiods of operation.Smali loose pieces of wood or other objectsthat contact the rear of the revolving blade canbe thrown back at the operator at very highspeed. This can usually be avoided by keepingthe guard and spreader in place for all thru-sawing operations (sawing entirely thru thework) AND by removing all loose pieces fromthe table with a long stick of woodIMMEDIATELY after they are cut offUse extra caution when the guard assembly isremoved for resawing, dadoing, rabbeting, ormolding ,-- replace the guard as soon as thatoperation is completedFor rip or rip-type cuts, the following end of aworkpiece to which a push stick or push boardis applied must be square (perpendicular tothe fence) in order that feed pressure appliedto the workpiece by the push stick or blockdoes not cause the workpiece to come awayfrom the fence, and possibly cause a kickbackDuring rip and rip type cuts, the workpiecemust be held down on the table and againstthe fence with a push stick, push block, and/orfeatherboards A featherboard is made of solidlumber per sketch
5/I 6" APA_RT
G NEVER turn the saw "ON" before clearing thetable of all tools, wood scraps, etc, except theworkpiece and related feed or support devicesfor the operation planned
H NEVER place your face or body in line with thecutting tool.
t NEVER pface yourfingers or hands in the pathof the sawblade or other cutting tool
J NEVER reach in back of the cutting tool witheither hand to hold down or support theworkpiece, remove wood scraps, or for anyother reason Avoid awkward operations andhand positions where a sudden slip couldcause fingers or hand to move into a sawbladeor other cutting tool
K. DO NOT perform layout, assembly, or setupwork on the table while the cutting tool isrotating
L, DO NOT perform any operation"FREEHAND" -- always use either the ripfence or the miter gauge to position and guidethe work
M NEVERusetheripfencewhencrosscuttingorthe mitergaugewhenripping,DO NOTusethe rip fenceasa lengthstopNeverholdontoortouchthe"freeend"oftheworkpieceor a "free piece"that is cut off,whilepoweris "ON"and/orthe sawbladeisrotating
N Shut"OFF"thesawanddisconnectthepowercord when removing the table insert,changing the cutting tool, removing orreplacing the blade guard, or makingadjustments
O Provideadequatesupport to the rear andsides of the saw table for wider or tongworkpieces
P.Plastic and composition (like hardboard)materialsmaybecut onyoursaw However,since these are usually quite hard andslippery,theantikickbackpawlsmaynotstopa kickback,Therefore,beespeciallyattentiveto followingproper set-up and cutting proceduresforripping Donotstand,orpermitanyoneelsetostand,in linewitha potentialkickback
Q If you stall or jam the sawbladein theworkpiece, turn saw "OFF", remove theworkpiecefrom thesawblade,andchecktosee if the sawbladeis parallelto the mitergaugegroovesandif thespreaderis inproperalignmentwiththesawbladeIf rippingat thetime,checkto seeif the rip fenceis parallelwith thesawbladeReadjustas indicated
R DO NOT remove small pieces of cut-offmaterialthat maybecometrappedinsidethebladeguardwhile the saw is running Thiscould endanger your hands or cause akickbackTurnsaw"OFF"andwaituntilbladestops
S. Useextracarewhenrippingwoodthat hasatwistedgrainor is twistedor bowedi it mayrockon thetableand/orpinchthesawblade
T Nevergangcrosscutor rip -- lining up morethan one workpiece in front of the blade(stacked vertically, or horizontally outward onthe table) and then pushing throughsawblade The blade could pick up one ormore pieces and cause a binding or loss ofcontrol and possible injury
9. KNOW YOUR CUTTING TOOLSA° Dull, gummy, or improlSerly sharpened or set
cutting tools can cause material to stick, jam,stall the saw, or kickback at the operatorMinimize potential injury by proper cuttingtool and machine maintenanceNEVER ATTEMPT TO FREE A STALLEDSAWBLADE WITHOUT FIRST TURNINGTHE SAW OFF.
B- Never use grinding wheels, abrasive cut-offwheels, friction wheels (metal slitting blades)wire wheels or buffing wheels
10o USE ONLY ACCESSORIES DESIGNED FORTHIS SAW,
11_ Make sure the top of the arbor or cutting toolrotates toward you when standing in normaloperating position Also make sure the cuttingtool, arbor collars and arbor nut are installedproperly Keep the cutting tool as low as
possible for the operation being performedKeep all guards in place whenever possible
12_ Do not use any blade or other culling toolmarked for an operating speed less than 3450RPM. Never use a cutting tool larger in diameterthan the diameter for which the saw wasdesigned. For greatest safety and efficiencywhen ripping, use the maximum diameter bladefor which the saw is designed, since under theseconditions the spreader is nearest the blade.
13. NEVER operate the saw unless the proper insertis installed
14, NEVER feed material into the cutting tool fromthe rear of the saw An accident and seriousinjury could result
t5, NEVER use another person as a substitute for atable extension, or as additional support for aworkpiece that is longer or wider than the basicsaw table, orto assist in feeding or supporting orpulling the workpiece,DO NOT pull the workpiece through thesawblade -- position your body at the nose (in-feed) side of the guard: start and complete thecut from the same side This will require addedtable support for tong or wide workpieces thatextend beyond the length or width of the sawtable
16. THINK SAFETY.Safety is a combination of operator commonsense and alertness at att times when the saw isbeing used
r
17_ NOTE AND FOLLOW SAFETY INSTRUC-TIONS THAT APPEAR ON THE FRONT OFYOUR SAW.
li E=ANGERI o. ou. ow.sAFETY:READ AND UNDERSTAND OWNERS MANUAL BEFORE OPERATING MACH|NE
I WE,AR 5AFE'T_ GOGGLES 5 KNOW HOW TO AVOIO'*_ICt_ACKS,*
U_E I_AWSLAI_E GG_gO FOR 1 H P_$_SAWING _ DO t_O_ tJ_.RFORM OP_RATION_ 'F_ EEHAf_I
_EEP HANOS OUr OF PATP: OF _AWI_t.A_E I NI_VE _ REACH AAOURL1 On OV,_ _ _AWgLA D_
U_E A ' PUSH'$T_CK =' WHEN R[QUIR_O
WARNING: use 1_0 VOLT 15 A_P a_NCH CtRCIJtT AtG3 USE I_ AMP TiME DELAY I_GJSE
18. WARNING: DO NOT ALLOW FAMILIARITY(GAINED FROM FREQUENT USE OF YOURSAW) TO BECOME COMMONPLACE.ALWAYS REMEMBER THAT A CARELESSFRACTION OF A SECOND IS SUFFICIENT TOINFLICT SEVERE INJURY.
NOTE: Do not overtighten arbor nut. Use the arborwrench to just "snug" it
WEAR YOUR
The operation of any power tool can result in foreignobjects being thrown into the eyes, which can resultin severe eye damage Always wear safety gogglescomptying with ANSI Z87 1 (shown on Package)before commencing power too! operation SafetyGoggles are available at Sears retail or catalogstores.
4
MOTOR SPEC FICATIONS ANDELECTR!CAL REQUIREMENTS
MOTOR SPECIFICATIONSThe AC motor used in this saw is a non-reversibletype, with the following specifications:
Amperes ...................................... 7.8Hertz .................................... 60Phase ...................................... SingleRPM ................................... 3450Rotation (viewed from
Sawblade end) .......... CounterclockwiseMOTOR SAFETY PROTECTION
the Canadian Standards Association The groundconductor has a green jacket and is attached to thetoot housing at one end and to the ground prong inthe attachment plug at the other endThis plug requires a mating 3-conductor groundedtype outlet as shownWARNING: DO NOT PERMIT FINGERS TOTOUCH THE TERMINALS OF PLUGS WHENINSTALLING OR REMOVING THE PLUG TO ORFROM THE OUTLET.
MOTOR SAFETY PROTECTION1 REPEATED STALLING OF THE SAW BLADE
WILL SHORTEN THE LIFE OF THE MOTOR.Always avoid stalling the blade If the motor hasbeen abused (repeated stalling) and fails to start(hums), TURN THE SWITCH OFF, ALLOW THEMOTOR TO COOL, THEN RE-START IT
2 ALWAYS USE SHARP BLADES A dull bladerequires excessive power and does not producequality results
3. NOTE: The starting relay is a GRAVITYSENSITIVE TYPE. NEVER TURN THE POWERON WHILE TH E SAW tS UPSIDE DOWN AS THISWILL DAMAGE THE MOTOR.
4 Frequent opening of fuses or circuit breakersmay result if motor is overloaded, or if the motorcircuit is fused with a fuse other than thoserecommended Do not use a fuse of greatercapacity without consulting the power company°
5 Although the motor is designed for operation onthe voltage and frequency specified on motornameplate, normal loads will be handled safelyon voltages not more than 10% above or belowthe nameplate voltageHeavy loads, however, require that voltage atmotor terminals by not tess than the voltagespecified on nameplate
6 Most motor troubles may be traced to loose orincorrect connections, overloading, reducedinput voltage (which results when small size wiresare used in the supply circuit) or when the supplycircuit is extremely long Always checkconnection, load and supply circuit when themotor fails to perform satisfactorily. Check wiresizes and lengths with table at end of this section
CONNECTING TO POWER SUPPLY OUTLETIf power cord is worn or cut, or damaged in any way,have it replaced immediately.
WARNING: IF NOT PROPERLY GROUNDED THISPOWER TOOL CAN CAUSE AN ELECTRICAL SHOCKPARTICULARY WHEN USED IN DAMP LOCATIONSCLOSE TO PLUMBING. IF AN ELECTRICAL SHOCKOCCURSTHEREtSTHEPOTENTIALOFASECONDARYHAZARD SUCH AS YOUR HANDS CONTACTING
THE SAW BLADE.
If you are not sure that your outlet, as picturedbelow, is properly grounded, have it checked by aqualified electrician
Your unit is for use on 110=120volts, and has a plugthat looks like illustration belowThis power tool is equipped with a 3-conductor cordand grounding type plug which has a groundingprong, approved by Underwriters' Laboratories and
@
3-PRONG PLUG
GROUNDING PRONG
"_ PROPERLY GROUNDED3-PRONG OUTLET
Plug power cord into a 110-120V properly groundedtype outlet protected by a 15-amp dual elementtime delay or CircuibSaver fuse or circuit breakerIf the outlet you are planning to use for this powertool is of the 2 prong type, DO NOT REMOVE ORALTER THE GROUNDING PRONG IN ANYMANNER Use an adapter as shown below andalways connect the grounding lug to knownground.A temporary adapter as shown below is available forconnecting plugs to 2-prong receptacles The greengrounding lug extending from the adapter must beconnected to a permanent ground such as to aproperly grounded outlet boxA temporary adapter as illustrated is available forconnecting plugs to 2-prong receptacles Thetemporary adapter should be used only until aproperly grounded outlet can be installed by aqualified electrician
GROUNDING LUG
_ MAKE SURE THIS tS
3-PRONG _"'_- _-_ CONNECTED TO APLUG _-'l(_'_lt KNOWNGROUND
/ _ RECEPTACLE
ADAPTER
WARNING: THE GREEN GROUNDING LUGEXTENDING FROM THE ADAPTER MUST BECONNECTED TO A PERMANENT GROUNDSUCH AS TO A PROPERLY GROUNDED OUTLETBOX. NOT ALL OUTLET BOXES ARE PROPERLYGROUNDED.If you are not sure that your outlet box is properlygrounded, have it checked by a qualified electrician.NOTE: The adapter illustrated is for use only if youalready have a properly grounded 2-prongrec'eptacte_ Adapter is not allowed in Canada by theCanadian Electrical Code
Theuseof anyextensioncordwillcausesomelossof power.To keepthistoa minimumandtopreventover-heatingandmotorburn-out,usethefollowingtableto determinetheminimumwiresize(A.WoG)extensioncord.Useonly3wireextension¢ordswhichhave3-prong
groundingtypeplugsand3-polereceptacleswhichacceptthe toolsplug.Extension Cord Length Wire Size A.W.G.
Up to 100 Ft .............................. !4100-200 Ft .................................. 12200-400 Ft .................. ............... 8
CONTENTS
WARRANTY ....................................... 2
GENERAL SAFETY INSTRUCTIONSFOR POWER TOOLS ............................ 2
ADDITIONAL SAFETY INSTRUCTIONSFOR TABLE SAWS ........................... 3
MOTOR SPECIFICATIONS AND ELECTRICALREQUIREMENTS ............................ 5
UNPACKING AND CHECKING CONTENTS ., 6Tools Needed ............................... 6List of Loose Parts ........................... 7
ASSEMBLY .......................................... 7Installing Handwheels ........................... 7Adjusting Blade Insert ....................... 8Checking Heeling or Parallelism of
Saw Blade to Miter Gauge Groove ............ 9Adjusting Parallelism of Saw Blade to MiterGauge Groove ................................ 9
Adjusting 90 Degree Bevel Stop ............. 10Adjusting Bevel Pointer ........................ 11Adjusting 45 Degree Bevel Stop ............. I2Installing Table Extensions ................. 12Aligning Table Extensions ................... 13To Raise Extension ...................... 13To Lower Extension .............................. 14Leveling Extensions ........................ 14To Lower Outer Edge of Extension ........ 14TO Raise Outer Edge of Extension .......... 14Aligning Table Extensions with Front of Table I5To Move Outer Edge of Extension Back ..... 15To Move Outer Edge of Extension Forward , 15Installing Blade Guard ........................ 16Aligning Spreader ............................... 17Attaching Rip Fence ........................... 18Aligning Rip Fence ....................... 19Adjusting Miter Gauge ...................... 19Mounting Saw to Legs or Bench ............. t9
,,u,u,H ' ' ="'111
UNPACKING AND
TOOLS NEEDED
Medium Screwdriver 7/16 tn.
#2 Phillips ScrewdriverLong Nose Pliers
Combination Square
Hex "L" Wre_
3/16", t/8", 5/32"
GETTING TO KNOW YOUR SAW ........... 20On-Off Switch ................................. 20Elevation Handwheel ......................... 21Tilt Handwheel .................................. 21Miter Gauge ................................ 21Blade Guard .............................. 21Table Insert ................................... 21Rip Fence .................................... 21Removing and Installing Saw Blade ......... 21To Install Saw Blade ........................... 22
BASIC SAW OPERATION USING THEMITER GAUGE .................................. 23Work Helpers ................................ 23Crosscutting .................................. 24Repetitive Cutting ............................. 25Miter Cutting ............................... 25Bevel Crosscutting ............................... 26Compound Miter Cutting ..................... 26
BASIC SAW OPERATION USING THERIP FENCE ..................................... 26Ripping ...................................... 27Bevel Ripping ..................................... 27Ploughing and Molding ...................... 29Resawing ...................................... 29Rabbeting .................................. 30Dadoing ..... .................................. 30Molding and Cutting ......................... 30Using Featherboards ........................... 31
MAINTENANCE ............................... 31
LUBRICATION ..................................... 32
RECOMMENDED ACCESSORIES ............. 33
TROUBLE SHOOTING ......................... 33
REPAIR PARTS .................................. 35
CHECKING CONTENTSCOMBINATION SQUARE MUST BE TRUE°
STRAIGHT EDGE OF BOARD3t4" THICK. THIS EDGE MUST
DRAW LIGHT LINE ON BE PERFECTLY STRAIGHTTHIS EDGE _'_
BOARD ALONG "} ",
SHOULD BE NO GAP OR OVERLAPHERE WHEN SQUARE IS FLIPPED
OVER tN DOTTED POSITION
Model 1! 3221611 Table Saw with Table Extensionsis shipped complete in one cartonSeparate all parts from packing materials and checkeach one with the illustration and the list of LooseParts to make certain alf items are accounted for,before discarding any packing materialIf any parts are missing, do not attempt to assemblethe table saw, plug in the power cord or turn theswitch on until the missing parts are obtained andare installed correctly
Apioly a coat of automobile wax to the table.Wipe att parts thoroughly with a clean, dry cloth.WARNING: FOR YOUR OWN SAFETY, NEVERCONNECT PLUG TO POWER SOURCE OUTLETUNTIL ALL ASSEMBLY STEPS ARE COMPLETE,AND YOU HAVE READ AND UNDERSTAND THESAFETY AND OPERATIONAl, INSTRUCTIONS_
ITEMABCDEFG
LIST OF LOOSE PARTSDESCRIPTION QTY.
Guard Assembly ....................... 1Extension Table LH ...................... 1Extension Table R..H................... 1Handwheel .............................. 2Rip Fence Assembly ................... 1Miter Gauge Assembly ................. 1Owners Manual ...................... 1
Loose Parts Bag No. 507545(Containing the following items):
H Wrench, Arbor .......................... 1J Wrench, Shaft .......................... 1K Support, Spreader ..................... 1L Bracket, Spreader ..................... 1M Clamp, Spreader_.. .................. tN Nut, Wing 1/4-20 ....................... 2
Loose Parts Bag No. 507546(Containing the following items):
O Washer, t7/64 x 9/16 x 3/64 .......... 4P Screw, Pan Hd. 8_32 x 3/8 ............ 2Q Nut, Sq.. 1/4-20 ........................ 2R Screw, Soc. Set 1/4-20 x 7/8 ......... 2S Lockwasher, Ext. I/4 ................ 4S Lockwasher, Ext. #8 ...................... 2T Nut, Hex 1/4-20 ........................ 2U Screw, Truss Hd 1/4-20 x 5/8 ......... 2V Screw, Flat Hd 1/4-20 x 5/8 ............ 14W Key,Switch ........................... 1
F
D
--- o
_R
_S
INSTALLING HANDWHEELS1 From among the loose parts find two #8 external
tockwashers and two 8-32 x 3/8 inch long Phillipsscrews
2. Install elevation handwheel onto elevation shaft
by lining up FLAT SPOT on shaft with flat insidehandwheel. Install screw and Iockwasher.
3. Install bevel handwheel onto bevel shaft bylining up FLAT SPOT on shaft with flat insidehandwheet, Install screw and Iockwasher
WARNING: Failure to complete the following twosteps could result in damage to your saw.4. Turn elevation handwheel counter-clockwise to
pull motor away from inner packing cardboard,5 Remove cardboard.
ASSEMBLY
LO(
SCREW
REMOVE CARDBOARD FROMUNDERNEATH MOTOR
LOCKWASHER
SCREW
7
ADJUSTING BLADE INSERT1,,Turn saw over
2, Loosen Phillips screw in blade insert do notremove,
3 Remove blade insert by lifting slightlyand pullinginsert toward front of saw to disengage from keyhole slot
BLADE INSERT
HEADSCREW
4, Tab at rear of insert should engage in saw tablefirmly It may be necessary to bend tab slightlyusing pliers.
\
5 Install blade insert by placing keyhole slot ininsert over screw head in saw table and pushinginsert to rear of saw table sliding tab in insertunder saw table ledge
Tighten screw
CHECKING HEELING OR PARALLELISMOF SAW BLADE TO MITER GAUGEGROOVE
While cutting, the material must move in a straightline PARALLEL to the SAW BLADE . . thereforeboth the miter gauge GROOVE and the RIP FENCEmust be PARALLEL to the SAW BLADE
If the saw blade is not parallel to the miter gaugegroove, it is said to have "HEEL" This condition cancause the workpiece to bind or move workpieceaway from the rip fence at the end of a cut, possiblycausing a kickback
WARNING: TO AVOID INJURY FROMACCIDENTAL START MAKE SURE SWITCH IS"OFF" AND PLUG IS NOT CONNECTED TOPOWER SOURCE OUTLET.
1. Elevate blade to maximum height by turningelevation handwheef
2. Mark an "X" on one of the teeth which _s SET(bent) to the LEFT
3, Place the head of a combination square in theMITER GROOVE. Adjust blade of square so that itjust touches the tip of the MARKED tooth
4. Move squar;_ to REAR, rotate blade to see ifMARKED tooth again touches blade of square.
5 If tooth touches square the same amount atFRONT and REAR, sawblade is PARALLEL toMITER GAUGE GROOVE
\
MARK 'X" ONTOOTH
ADJUSTING PARALLELISM OF SAWBLADE TO MITER GAUGE GROOVE
If tooth does not touch front and rear themechanism underneath must be adjusted to makethe blade PARALLEL to miter gauge groove
1. Loosen the four hex socket screws in the top ofthe table next to the saw blade using a 3/16 inchhex L wrench This will allow the mechanismbelow the table to be shifted sideways
//
2 Fold a piece of cardboard or heavy paper over theblade to protect your hands
3 Grasp the blade and the cradle rod and move themechani,sm right or left a small amount as neededto make the square touch the same amount frontand rear Tighten one screw
4 Check with squareto determine if MARKED toothtouches square the same amount at front andrear
tf it does -- alternately tighten other three screwssfowly
If it does not -- loosen screw and move blade therequired amount
5 Recheck blade clearance to table and table insertto make sure blade does not hit
NOTE: Use the hex L wrench as shown Do not useapair of pliers or any other tool to gain more leverageon the setscrew wrench
ADJUSTING 90 DEGREE BEVEL STOP
(IMPORTANT: Blade must be square (90 ° ) to tablein order to accurately align the saw° Using care inthe following adjustments will help assure accuratewoodworking cuts.)WARNING: TO AVOID INJURY FROMACCIDENTAL START, TURN SWITCH "OFF" ANDREMOVE PLUG FROM POWER SOURCE OUTLETBEFORE ADJUSTING BEVEL STOP.
t Raise blade to highest elevation
2 Turn bevel handwheet just until it stops undermoderate pressure Blade should be 90° to thetable top
3 Place a square flush on the table top to the left ofthe sawblade and slide the square up against thebody of the sawblade, NOT against the teeth ofthe blade
4 The square should be nearly flush with the bodyof the sawblade When this is so, the sawblade issaid to be 90° with respect to the table topNotice the bevel pointer on the front of the sawThe pointer should be at 0°
5, If you feel the blade is not close enough to 90°with respect to the table top, further adjustmentcan be made by performing the followingoperation&.
IO
ADJUSTING 90 DEGREE BEVEL STOP
1 On the stop bracket are two t0-32 pan headscrews which set 90° stop position. If condition Aexists the two screws need to be turned clockwiseto obtain 90° setting if condition B exists thestews should be turned counterclockwise
[ t/BLADE
IItl
I I.,.,.,,-'_BLADE
HIF
H
If
2.. Turn saw over
3, Rotate bevel crank blade is in approximateFy 40°position and using phillips screwdriver rotatescrews slightly in direction necessary to correctgap, (rotate screws equally),. Recheck bladeposition and readjust if necessary
4, When 90° stop position is adjusted to yoursatisfaction re-adjust pointer to 0° position,
BEVELSTOP BRACKET
BEVEL SHAFT X_
BEVEL ADJUSTINGSCREWS
BEVELHANDWHEEL
l
ADJUSTING BEVEL POINTER
If blade IS SQUARE to table:
1,, Check pointer.
If POINTER DOES NOT point to the "0" mark on thebevel scale:
2 Remove Elevation Handwheel
3 Loosen screw and adjust pointer usingmedium screwdriver
4o Install Elevation Handwheel
! r
@
BEVELPOINTER
@
@
11
CHECKING 45 DEGREE BEVEL STOP
1 Turn elevation handwheet clockwise to raiseblade as high as it will go ,,
t/
2oTurn bevel handwheel clockwise to tilt blade to /,H45 °
3 Lay head of combination square on the blade ofsquare as illustrated and place head against theblade Make sure square is not touching TIP ofone of the saw TEETH
4, The 45° blade stop is set during manufacturing.If adjustment is needed proceed to next step,, Ifbevel adjustment is satisfactory go on to installing ttable extensions I
ADJUSTING 45 DEGREE BEVEL STOP
! The 45° blade position is controlled by thelocation of the sheet metal nut on end of bevelshaft
2, ff condition A exists the sheet metal nut needs tobe turned clockwise (CW) to obtain 45° setting Ifcondition B exists the nut should be turnedcounterclockwise (CCW),
3 To correct condition A - Rotate bevel handleCCW approximately 2 turns, place 11/16 inchwrench on sheet metal nut and hold in placewhile rotating handle counterclockwise in smallincrements Recheck blade position after eachrotation.
4. To correct condition B - Same procedure as No3, except, rotate handle clockwise while holdingnut,
5, Check blade clearance by rotating blade by handmaking sure blade does not strike insert or table
SHEET METAL BEVEL LINK
WASHER BEVEL SHAFT
ANGLE A
\\\\
\\\\
\/" \\
/
ANGLE
\x\\
\\_X
INSTALLING TABLE EXTENSIONS
1, Among toose parts locate fourteen 1/4-20 x 5/8inch tong flat head hex socket screws
2 Install right table extension and install sevenscrews using a 5/32 inch hex L wrench. Just startscrews
3 Install left table extension and install sevenscrews using a5/32 inch hex Lwrench Just startscrews
FLAT HEADHEX SOCKET
SCREWS
12
3 Install left table extension and install sevenscrews using 5/32 inch hex L wrench Just startscrews
ALIGNING TABLE EXTENSIONS
NOTE; The table extensions must be the sameheight as the table and level,Place combination square on table and extension,
"-_ EXTENSION SHOULDBE SAME HEIGHT
AS TABLE
TO RAISE EXTENSION
1, If extension is low loosen three screws on top ofthe table extension A, B, and C See illustration
2, Tighten screws D, E, F, and G underneath tableextension to raise extension even with table topfront and rear
3, Check height with square and tighten A, Band C4, Repeat for left extension
L==J I"
lEXTENS{ON
13
TO LOWER EXTENSION
!. If extension is too high loosen four screws onunderside of the extension D, E, F, and G. Seeillustration.
2 Tighten screws A, B and C on top of tableextension to lower extension even with table topfront and rear.
3. Check height with square and tighten screws D,E, F and G
4. Repeat for left extension.,,,u,
EXTENSfON
LEVELING EXTENSIONS
Place combination square on table and extension sothat end of blade extends over edge of extension.HoLd square firmly on saw table and check for gapbetween extension and blade of square.
SHOULD BENO GAP
TO LOWER OUTER EDGE OF EXTENSION
1. Loosen screws B_E, and Fon right extension. SeeilhJstration
2 Tighten screws C, D, and G until table extensionis Level
3oSnug down screws B, E, and Fr.
4 Repeat for left extension
EXTENSION
TO RAISE OUTER EDGE OF EXTENSION
1 Loosen screws C, D, and G on right extension.
2. Tighten screws B, E, and F until table extension istevet
3. Snug down screws C, D, and G
4. Repeat for left table extension.1
EXTENSION
14
ALIGNING TABLE EXTENSIONS WITHFRONT OF TABLE
!, Place blade of combination square on front oftable and table extension,,
2, Extension should line up with table,
'l'l='l'_'l'_'l'l'l'_'t'l'l'I'l'J'l,t'l'l'l'l't'l,l't,tI' I
TO MOVE OUTER EDGE OFEXTENSION BACK
1 Loosen screws C and F in right extension Seeillustration
2, Tighten screws B and G until extension is linedup,
3 Snug down screws C and F4, Recheck level and flatness to table
5, Check left extension
6. Adjust left extension in same manner
F G
TO MOVE OUTER EDGE OFEXTENSION FORWARD
1 Loosen screws B and G in right extension
2, Tighten screws C and F until extension is linedup
3, Snug down screws B and G4 Recheck level and flatness to table Check left
extension,4_ Recheck level and flatness to table
5 Check left extension
6 Adjust left extension in same manner
lltI! l
, LH|S
INSTALLING BLADE GUARD
1. From among the loose parts, find the hardware asshown
SQUARE NUT
_....._ , _..,_F SPREADER St'IPPORT
TRUSS HEAD _ _ SPREADER BRACKETSCREW _ _ J"
5/8 IN LONG "_,_(7"_ K-_}_-"_'_.,.,_ SPREADER CLAMP1 /
SOCKETHEAD _SETSCREW _,_-_,_1_ "-_ (J'-- I WING NUT
718,.,Lo.a g "IL_&j /FLAT WASHER/_) @'_.
HEX NUT -"-'_'_ LOCKWASHEREXT, 1/4 IN.
BLADE SQUAREWITH TABLE
2 MAKE SURE THE BLADE IS ALL THE WAY UPAND SQUARE WITH THE TABLE
3, Position SPREADER SUPPORT on rod until it iseven with the end of the rod
SPREADER SUPPORTEVEN WITH ROD
4. Assemble the 7/8 in, long setscrews, nuts,Iockwashers and washers to the SPREADERSUPPORT BRACKET and slip the nuts into theslot in the spreader support
5 Finger tighten ONLY THE HEX NUTS
16
6 Layapieceof flat straightwoodandasquareonsawtableandrotatetheSPREADERSUPPORTuntil the bracketis alignedwithsquare
7 MAKE SUREENDOF SUPPORT,BRACKETANDRODAREEVEN.,+usingan1/8in+HexLwrench,TIGHTENTHESETSCREWSONLY,
ENDS OF SUPPORTAND BRACKET TOBE EVEN WITHEND OF ROD
TIGHTENSETSCREW ONLY
ALIGNING SPREADER
IMPORTANT: The SPREADER must always bePARALLEL to the sawblade and in the MIDDLE ofthe cut (KERF) made by the sawblade.NOTE: The spreader is thinner than the width of theKERF by approximately six thicknesses of paper
SPACE EQUAL TO APPROX3 THICKNESSES OF PAPER KERF WOOD
.... :_ o/ J
/SPREADER
SPACE EQUAL TOAPPROX, LOOKING DOWN ON SAW3 THICKNESSES OF PAPER
1 Make two folds in a small piece (6 x 6 in,,) ofordinary NEWSPAPER making threethicknesses The folded paper witl be used as a"spacing gauge"
17
2, Installthe SPREADERCLAMP.Placespreaderbetweenspreaderclamp and bracket, Moveforwarduntilall threeareinline,TIGHTENWINGNUTS.
3 Lay a piece of straight flat wood againstthesawblade.Insertfoldedpaperbetweenspreaderandstripof wood.
4,MAKESURETHE HEXNUTSUNDERNEATHARELOOSE
5 Lift the antikickbackpawlto clearthewoodandholdthespreadertightlyagainstthewood,Makesure the wood is against the saw bladeTIGHTENTHEHEXNUTS,This will alignthespreaderin themiddleof thecut (KERF)madeby sawblade
THREE THICKNESSES
OFPAPER SPREADER
WING NUT CLAMP
PIECE OFSTRAIGHT WOOD
HOLD WOOD 1"IGHTLY AGAINSTBLADE
ACK
HOLD SPREADERTIGHTLY AGAINST WOOD
BRACKET
ATTACHING RIP FENCE
Apply a coat of paste wax to the top surface andfront ledge of the saw table This will allow the fenceto slide more easily
1 Loosen fence lock knob by turning counter-clockwise,.
2. Attach fence head by placing head of fence overfront ledge in saw table.,
FENCE LOCKKNOB
18
ALIGNING RiP FENCE
IMPORTANT: The rip fence MUST be parallel withsaw blade and miter grooves in order to help preventKICKBACK of the workpiece when ripping. Carefuladjustment is required,1..Hold head of rip fence and slide on table until the
edge of the fence lines up with the right miter slot.2 Turn fence lock knob clockwise to lock fence.
3 If..fence does not line up with miter slot front andrear:A. Loosen the two hex screws in top of fence
B. While holding head of rip fence, move rear ofrip fence right or left until edge lines up withmiter s!ot_
C Tighten hex screws alternately being carefulnot to move fence
MUST LINE UP WITH MITERSLOT FRONT AND REAR
HEAD
LOOSEN TWO HEXSCREWS TO ADJUST
ADJUSTING MITER GAUGE
NOTE: The graduations are manufactured to veryclose tolerances which provide suitable accuracyfor average woodworking. In some cases whereextreme accuracy is required, when making anglecuts, for example, make a trial cut and then recheckit.
If necessary, the miter gauge head can then beswiveled slightly to compensate and then lockedThe HEAD should be SQUARE (90 ° ) with the barwhen the pointer points to "0".To check for squareness, place an accurate squareon the mitergauge If the head is NOTSQUAREwiththe bar:
1. Loosen the lock handle.
2 Position the head square with the bar .. • tightenthe handle
3 Loosen the screw and adjust the pointer, so itpoints to zero
BAR
HEAD
MOUNTING SAW TO LEGS OR BENCH
If you purchase Craftsman Steel Legs for your saw,assemble them according to the directionsfurnished with them
If you mount the saw on any other bench, makesurethat there is an opening in the top of the bench thesame size as the opening in the bottom of the saw sothat the sawdust can drop through, Recommendedworking height is 33 to 37 in. from the fop of the sawtable to the floor°
4 HOLES.312 DIA'
12-3/4REAR OF SAW
OPENING
11-3/16
NOTE; All dimensions in Inches,
19
GETTING TO KNOW YOUR SAW
5 BLADE GUARD
SPREADER 6 TABLE INSERT\
8 SAW BLADE "k* RIP FENCE
TABLE EXTENSION
4 MITERGUAGE
MITER GUAGELOCK KNOB
3 TILT HANDWHEEL
POWER CORD
TTABLE
EXTENSION
RIP FENCELOCK KNOB
,BEVEL SCALE
BEVEL POINTER
2 ELEVATION HANDWHEEL
1 ON-OFF SWITCH
1. ON-OFF SWITCHCAUTION: Before turning switch on, make surethe blade guard is correctly installed andoperating properly,The On-Off Switch has a locking feature. THiSFEATURE IS INTENDED TO HELP PREVENTUNAUTHORIZED AND POSSIBLE HAZARDOUSUSE BY CHILDREN AND OTHERS
A Insert Key into switchB TO turn saw ON stand to either side of the
blade never in line with it. insert finger underswitch lever and pull END of lever out
After turning switch ON, always allow theblade to come up to fuff speed before cutting
Do not cycle the motor switch on and offrapidly, as this may cause the sawblade toloosen In the event this should ever occur,allow the sawblade to come to a complete stopand retighten the arbor nut normally, notexcessively. Never leave the saw while thepower is "ON"
C TO turn saw OFF PUSH lever in Neverleave the saw until the cutting toot has come toa complete stop
D To lock switch in OFF position hold switchIN with one hand REMOVE key with otherhand
WARNING: FOR YOUR OWN SAFETY,LOWER BLADE OR OTHER CUTTING TOOLBELOW TABLE SURFACE. (IF BLADE ISTILTED, RETURN IT TO VERTICAL (90 ° )POSITION). ALWAYS LOCK THE SWITCH
f
INSERT KEY
TURN O\F_F _, _ \_-=_,_
TURN ON
REMOVE KEY
"OFF", WHEN SAW IS NOT IN USE o , .REMOVE KEY AND KEEP IT IN A SAFEPLACE . , . ALSO , , . IN THE EVENT OF APOWER FAILURE (ALL OF YOUR LIGHTSGO OUT) TURN SWITCH OFF,. , LOCK ITAND REMOVE THE KEY. THIS WILLPREVENT THE SAW FROM STARTING UPAGAIN WHEN THE POWER COMES BACKON.
2O
2. ELEVATION HANDWHEEL ,elevates orlowersthe blade, Turn counterclockwise to elevateclockwise to lower
3. TILT HANDWHEEL tilts the blade for bevelcutting Turn counterclockwise to tift toward left, clockwise to tilt toward rightWhen the blade is tilted to the LEFT as far as it wittgo, it should be at 45° to the table and the bevelpointer should point 45°NOTE: There are LIMIT STOPS inside the sawwhich prevent the blade from tilting beyond 45 °to the LEFT and 90° to the RIGHT (See"Adjustments" section "Blade Tilt, or Squarenessof Blade to Table")
4. MITER GAUGE head is locked in position forcrosscutting or mitering by tightening the lockknob ALWAYS LOCK IT SECURELY WHEN INUSE
5. BLADEGUARD must always be in place andworking properly for all thru-sawing cuts That is,all cuts whereby the blade cuts completelythrough the workpiece
To remove the guard for special operation,loosen both wing nuts, slide spreader back andup. DO NOT DISTURB THE SETTING OF THESPREADER SUPPORT BRACKETWhen replacing the guard, insert spreaderbetween bracket and clamp and slide forwardTIGHTEN BOTH WINGNUTS SECURELY
6. TABLE INSERT is removable for removing or"installing blades or other cutting tools
WARNING: FOR YOUR OWN SAFETY, TURNSWITCH "OFF" AND REMOVE PLUG FROMPOWER SOURCE OUTLET BEFOREREMOVING INSERT.A Lower the blade below the table surface
B Raise blade guard
C Loosen Screw (Do Not Remove)
,
D, Lift insert from front end, and pull toward frontof saw
NEVER OPERATE THE SAW WITHOUT THEPROPER INSERT IN PLACE. USE THE SAWBLADE INSERT WHEN SAWING . . USE THEMOLDING INSERT WHEN MOLDING
RIP FENCE, is locked in place by tightening thelock knob To move the fence, loosen the knoband grasp the fence with one hand at the front
Holes are provided in the rip fence for attaching awood facing when using the dado head, ormolding head
Select a piece of smooth straight wood approx3/4" thick, at least as long as the rip fence, and atIeast 7-1/2" wide (high) to permit clamping offeatherboards
Attach it to the fence with two Round Head #10Wood Screws 2 in long To remove the facing,loosen the screws, slide the facing forward andpuli the screws through the round holes
WOOD FACING
\
\ \
# 10 WOOD SCREWS
CAUTION: When positioning fence for maximumrip, make sure end of fence HEAD is even with edgeof table extension. Fence cannot be locked securelybeyond the edge of the table extension.
REMOVING AND INSTALLINGSAWBLADE
WARNING: TO AVOID INJURY FROMACCIDENTAL START, TURN SWITCH "OFF" ANDREMOVE PLUG FROM POWER SOURCE OUTLETBEFORE REMOVING OR INSTALLINGSAWBLADE.
NOTE: When installing the blade make sure theupper saw teeth are pointing toward the front of thesaw, and that the blade and collars are clean, andfree from any burrsThe HOLLOW side of the collars must be against theblade.
NOTE: Always place the LARGE collar on the shaftbefore the blade
NOTE: Do not overtighten arbor nut Use the arborwrench to just "snug" it
1 Loosen Phillips head screw in blade insert Donot remove
2 Remove blade insert by lifting stightly and pullinginsert to disengage from key hole slot
PHILLIPSBLADE INSERT HEAD SCREW
I
21
3, Turn elevation handwheel clockwise to raisemotor shaft as high as it will go,
4, Insert shaft wrench over flat portions of motorspacer and arbor wrench over arbor nut
5 Hold shaft wrench and loosen arbor nut witharbor wrench
ARBORWRENCH
t
TO INSTALL SAWBLADE
1 Install large inner blade collar onto motor shaftwith rounded surface toward motor,,
2 Install saw blade onto shaft with top teethpointing toward front of saw
3 Install sina!! outer blade collar with flat surfacetoward blade
4, Install arbor nut Note: Arbor nut should just besnug Do not overtightenIMPORTANT: Do not attempt to run saw withoutboth blade collars properly installed_
FLAT SURFACES
TOP TEETH POINTINGTO FRONT OF SAW
LARGE COLLAR(2" DIAMETER)
SMALL COLLAR(1-3/4" DIAMETER)
HEX NUT
5, Install blade insert by placing keyhole slot ininsert over screw head in saw table and pushinginsert to rear of saw table engaging tab in insertonto saw table Iedge
Tighten screw.
22
BASIC SAW OPERATIONUSING THE MITER GAUGE
CROSSCUTTING, MITER CUTTING, BEVELCUTTING, COMPOUND MITER CUTTING andwhen RABBETING across the end of a narrowworkpiece, the MITER GAUGE is used
WARNING: FOR YOUR OWN SAFETY, ALWAYSOBSERVE THE FOLLOWING SAFETYPRECAUTIONS IN ADDITION TO THE SAFETYINSTRUCTIONS ON PAGES 2, 3, and 4.
1 Never make these cuts freehand (without usingthe miter gauge or other auxiliary devices)because the blade could bind in the cut andcause a KICKBACK or cause your fingers orhand to slip into the blade,
2., Always lock the miter gauge securely when inUSe.
3. Remove rip fence from table,
4, Make sure blade guard is installed for atl "thru-sawing" operations (when sawbiade cutsentirely thru the thickness of the workpiece,)Replace guard IMMEDIATELY after completionof dadoing, molding or rabbeting cuts.,
5. Have blade extend approximately 1/8 in abovetop of workpiece° Additional blade exposurewould increase the hazard potential,
6, Do not stand directly in front of the blade in caseof a THROWBACK (Small cut-off piece caught
7,
8.
by the back of the blade and thrown toward theoperator), Stand to either side of the bladeKeep your hands clear of the blade and out Ofthe path of the blade,
If blade stalls or stops while cutting, TURNSWITCH OFF before attempting to free theblade,,
9. Do not reach over or behind the blade to pul! theworkpiece through the cut,. oto support long orheavy workpieces, ,. to remove cut-off pieces ofmaterial or FOR ANY OTHER REASON
10, Do not pick up small pieces of cut-off materialfrom the table. REMOVE them by pushing themOFF the table with a long stick, Otherwise theycould be thrown back at you by the rear of theblade.
11. Do not remove small pieces of cut-off materialthat may become TRAPPED inside the bladeguard while the saw in RUNNING THIS COULDENDANGER YOUR HANDS or cause aK1CKBACK_
Turn the saw OFF. After the blade has stoppedturning, lift the guard and remove the piece.
12 If workpiece is warped, place the CONCAVEside DOWN This will prevent it from rockingwhile it is being cut,
WORK HELPERS
Before cutting any wood on your saw, study all ofthe "Basic Saw Operations'L
Notice that in order to make some of the cuts, it isnecessary to use certain devices "Work Helpers"like the Push Stick, the Push Block and the AuxiliaryFence, which you can make yourself
After you have made a few practice cuts, make upthese "helpers" before starting any projects, Makethe "Push Stick" first, To rip the piece for the pushstick, start out with a wide board, say 11-t/2 in. wideand set the rip fence 9-3/4 in. from the blade
PUSH STICK AND PUSH BLOCK
Make the Push Stick using a piece of 1 x 2.
Make the Push Block using a piece of 3/8 in and 3/4in. plywood
The small piece of wood 3/8 in, x 3/8 in, x 2-1/2 in.should be GLUED to the plywood ... • DO NOT USENAILS, This is to prevent dulling the sawblade in theevent you mistakingly cut into the push block,
Position the handle in the center of the plywood andfasten together with glue and woodscrews
SLIGHTLY LESS THANTHICKNESS OF WORKPIECE
UP TO
15
t-5/8
45 ° NOTCH
NOTE: All dimensions in inches
PUSH STICK
THESE EDGES MUSTBE PARALLEL
_\ 1"4"3/4_
3/4 PLYWOOD
114 -" 2-1/2
3/8
NOTE: All dimensions in inches 3/8 PLYWOOD
23
AUXILIARYFENCEMake one using a piece of 3/8 in,. and 3/4 in,plywood Fasten together with glue andwoodscrews
NOTE: Since the Push Block is used with theAuxiliary Fence, the 4-3/4 in dimensions must beheld identical on both the pieces.
3/8 PLYWOOD
THIS FACE ANDTHIS EDGE MUST
BE PARALLEL
14
3/'4 PLYWOOD
NOTE: All dimensions in Inches
AUXILIARY FENCE
CROSSCUTTING
CROSSCUTTING is cutting wood across the grain,at 90_, or square with both the edge and the flat sideof the wood This is done with the miter gauge andblade angle set at "0". The graduations on the mitergauge provide accuracy for average woodworkingIn some cases where extreme accuracy is required,when making angle cuts, for example, make a trialcut and then recheck it with an accurate square, orprotractor.
_f necessary, the miter gauge head can be swiveledslightly to compensate for any inaccuracy
NOTE: The space between the miter gauge bar andthe groove in the table is held to a minimum duringmanufacturing.
WORKPIECE
1 ,
TABLE
For maximum accuracy when using the mitergauge, always "favor" one side of the groove in thetable In other words, don't move the miter gaugefrom side to side while cutting, but keep one side ofthe bar riding against one side of the groove
NOTE: Glue a piece of sandpaper to the face of themiter gauge head, This will hetp prevent theworkpiece from "creeping" while it is being cut.
The miter gauge may be used in either of thegrooves in the table. Make sure locking knob is tight.When using the miter gauge in the LEFT handgroove, hold the workpiece firmly against the mitergauge head with your left hand, and grip the lockknob with your right
When using the RIGHT hand groove, hold theworkpiece with your right hand and the tock knobwith your left hand.
When cutting tong workpieces, make sure the end issupported from the floor..
PLYWOOD CLAMPEDTO SAWHORSE
SANDPAPER
LINE FOR CLARITY
24
REPETITIVE CUTTING
REPETITIVE CUTTING is cutting a quantity ofpieces the same length without having to mark eachpiece
NOTE: When making repetitive cuts from a longworkpiece make sure it is supported1 NEVER USE THE RIP FENCE AS A LENGTH
STOP BECAUSE THE CUTOFF PIECE COULDBIND BETWEEN THE FENCE AND THE BLADECAUSING A KICKBACK
2, When making repetitive cuts shorter than 6 in,clamp a block of wood 3 in long to the table to actas a length stop
CAUTION: When clamping the block, make surethat the end of the block is well in front of thesawblade, Be sure it is clamped securely.
3. Slide the workpiece along the miter gauge until ittouches the block,, hold it securely
4 Make the cut , pull the workpiece back _ pushthe cut off piece off the table with a long pushstick .. DO NOT ATTEMPT TO PICK IT UP ASTHIS COULD ENDANGER YOUR HANDS
MITER CUTTING
MITER CUTTING is cutting wood at an angle otherthan 90° with the edge of the wood Follow the sameprocedure as you would for crosscuttingAdjust the miter gauge to the desired angle, andlock it
The miter gauge may be used in either of thegrooves in the table
When using the miter gauge in the LEFT handgroove, hold the workpiece firmly against the mitergauge head with your left hand, and grip the lockknob with your right
When using the RIGHT hand groove, hold theworkpiece with your right hand and the lock knobwith your left hand
TOP VIEW
TABLE
25
BEVEL CROSSCUTTING
BEVEL CROSSCUTTING is the same as cross-cutting except that the wood is cut at an angleother than 90° with the flat side of the wood.
Adjust the blade to the desired angle
Use the Miter Gauge in the groove to the RIGHTofthe blade It cannot be used in the groove to theLEFT because the blade guard will interfere Holdthe workpiece with your right hand and the Dockknob with your left hand
WORKPIECE
TA!LE
?,1
COMPOUND MITER CUTTING
COMPOUND MITER CUTTING is a combination ofmiter cutting and bevel crosscutting The cut ismade at an angle other than 90° to both the edgeand the flat side of the wood
Adjust the miter gauge and the blade to the desiredangle. Make sure miter gauge is locked
USING THE RIP FENCE
RIPPING, BEVEL RIPPING, RESAWING ANDRABBETING are performed using the RiP FENCEtogether with the AUXILIARY FENCE/WORKSUPPORT, PUSH STICK OR PUSH BLOCK..
WARNING: FOR YOUR OWN SAFETY, ALWAYSOBSERVE THE FOLLOWING SAFETYPRECAUTIONS IN ADDITION TO THE SAFETYINSTRUCTIONS ON PAGES 2, 3 and 4.
1 Never make these cuts FREEHAND (withoutusing the rip fence or auxiliary devices whenrequired) because the blade could bind in thecut and cause a KICKBACK
2. Always lock the rip fence securely when in use
3. Remove miter gauge from table.
4 Make sure blade guard is installed for aft thru-sawing type cuts. Replace the guardIMMEDIATELY following completion ofresawing, rabbeting, dadoing, or moldingoperations
Frequently check the action of theANTtKICKBACK PAWLS by passing theworkpiece alongside of the spreader while sawis OFF
Pull the workpiece TOWARD you. If the PAWLSdo not DtG into the workpiece and HOLD it..the pawls must be REPLACED ORSHARPENED See "Maintenance" section
5 Have blade extend approximately 1/8 in abovetop of workpiece Additional blade exposurewould increase the hazard potential
6 Do not stand directly in front of the blade in caseof a KICKBACK Stand to either side of theblade
7 Keep your hands clear of the blade and out ofthe path of the blade,,
8 If the blade stalls or stops while cutting, TURNSWITCH OFF before attempting to free theblade
,r
10,
Do not reach over or behind the blade to pull theworkpiece through the cut., to support long orheavy workpieces , to remove small cut-offpieces of material or FOR ANY OTHERREASONS
Do not pick up small pieces of cut-off materialfrom the table. REMOVE them by pushing themOFF the table with a long stick Otherwise theycould be thrown back at you by the rear of theblade
11 Do not remove small pieces of cut-off materialthat may become TRAPPED inside the bladeguard while the saw is RUNNING, THIS COULDENDANGER YOUR HANDS or cause aKICKBACK,
Turn the saw OFF After the blade has stoppedturning, lift the guard and remove the piece,
12, If workpiece is warped, place the CONCAVEside DOWN, This will help prevent it fromrocking while it is being ripped.
26
RIPPING
RIPPING is cutting a piece of wood with the grain, orlengthwise. This is done using the rip fence,Position the fence to the desired WIDTH OF RIP andlock in place
Before starting to rip, be sureA, Rip Fence is parallel to sawblade.B Spreader is properly aligned with sawbfadeC. Anti-Kickback pawls are functioning properly,D Rip fence knob is tightened to secure the fence to
the table
Position the fence to the desired WIDTH OF RIP bymeasuring the distance from the sawblade
WORKPIECE
k.jTABLE
When ripping LONG BOARDS or LARGE PANELS,always t,_sea work support.
A simple one can be made by clamping a piece ofplywood to a sawhorse.
BEVEL RIPPING
When bevel ripping material 6 in or narrower, usefence on the right side of the blade ONLY. This willprovide more space between the fence and thesawblade for use of a push stick if the fence ismounted to the left, the sawbtade guard mayinterfere with proper use of a push stick
ALWAYS SUPPORTLONG WORKPIECES
When "WIDTH OF RIP" is 6 in and WIDER use yourRIGHT hand to feed the workpiece until it is c_ear ofthe table,
Use LEFT hand ONLY to guide the workpiece. Ldonot PUSH the workpiece with the left hand
27
When "WIDTH OF RIP" is 2 in, to 6 in, wide USE THEPUSH STICK to feed the work,
When "WIDTH OF RIP" is NARROWER than 2 in,,the push stick CANNOT be used because the guardwill interfere USE the AUXILIARYFENCEIWORK SUPI_ORT and PUSH BLOCK
Attach Auxiliary Fence/Work Support to rip fencewith two "C" clamps
Feed the workpiece by hand along the AUXILIARYFENCE until the end is approx, 1 in past the frontedge of the table Continue to feed using the PUSHBLOCK until the cut is complete.,
Hold the workpiece in position and instalf the PUSHBLOCK by sliding it on top of the AUXILIARYFENCE/WORK SUPPORT (This May Raise Guard)
\
\\
28
Narrow strips thicker than the Auxiliary Fence/WorkSupport may enter the guard and strike the baffleCAREFULLY raise guard only enough to clear theworkpiece. Use PUSH BLOCK to complete cut.
FLE
RESAWING
RESAWlNG is a "thru-sawing" cut made by rippinga piece of wood through its thickness Do notattempt to res'aw BOWED or WARPED materialNOTE: To RESAW a piece of wood it will benecessary to remove the blade guard _, and use theAUXILIARY FENCE/WORK SUPPORT. (See "WorkHelpers").
Clamp it to the table so that the workpiece willSLIDE EASILY but not TILT or MOVE SIDEWAYSwithout BINDING between the two fences.
Do not clamp directly to the bottom edge of the tablebecause the "swivel" of the clamp will not gripproperly Place a small block of wood between thebottom edge of the table and the "C" clamp.
WARNING: FOR YOUR OWN SAFETY . . :1. DO NOT "BACK UP" (REVERSE FEEDING)
WHILE RESAWING BECAUSE THIS COULDCAUSE A KICKBACK.
2, MAKE FIRST PASS TO A DEPTH SLIGHTLYLESS THAN ONE-HALF THE WIDTH OF THEBOARD; KEEP SAME FACE OF BOARDAGAINST FENCE FOR SECOND PASS AS THEFIRST PASS,
3. INSTALL BLADE GUARD IMMEDIATELY UPONCOMPLETION OF THE RESAWINGOPERATION,
SMALL BLOCKOF WOOD
PLOUGHING AND MOLDING
PLOUGHING is grooving with the grain the longway of the workpiece, using the fence. USE feather-boards and push sticks as required
MOLDING is shaping the workpiece with the grainthe long way of the workpiece, using the fence. Usefeatherboards and push sticks as required
PLOUGHING
29
MOLDING
RABBETING
RABBETING is known as cutting out a section of thecorner of a piece of material, across an end or alongan edge
To make a RABBET requires cuts which do not go allthe way through the material Therefore the bladeguard must be removed
1 Remove blade guard
2 For rabbeting along an edge (long way of work-piece) as shown, add facing to rip fence approxi-mately as high as the workpiece is wide Adjustrip fence and blade to required dimensions; thenmake first cut with board flat on table as any rip(type) cut; make second cut with workpiece onedge Foitow all precautions, safety instructions,and operational instructions as for ripping, or riptype operations, including feather boards andpush stick, etc
3 For rabbeting across an end, for workpiece 10-1/2" and narrower make the rabbet cut with theboard flat on the table Using the miter gaugefitted with a facing, follow the same proceduresand instructions for cross cutting making succes-sive cuts across the width of the workpiece toobtain the desired width of cut DO NOT use therip fence for rabbeting across the end
4, INSTALL BLADE GUARD IMMEDIATELY UPONCOMPLETION OF RABBETING OPERATION
RABB!
FIRST CUT
RABBETING ALONGTHEEDGE
RABBETINGACROSS THE END
Rabbet cuts can also be made in one pass of theworkpiece over the cutter using the dado head ormolding head
DADOING
Instructions for operating the Dado Head arecontained in booklet furnished with the Dado Head
The Recommended Dado Head is listed underRecommended Accessories in this manualThe arbor on the saw, is only long enough so thatthe widest cut that can be made is 1/2" wide
Do not install the outside loose collar beforescrewing on the arbor nut Make sure the arbor nutis tightALWAYS USE DADO INSERT LISTED UNDERRECOMMENDED ACCESSORIES
When using the dado head it will be necessary toremove the Blade Guard and Spreader USECAUTION, USE FEATHERBOARDS AND PUSHSTICKS AS REQUIRED
WARNING'. FOR YOUR OWN SAFETY, ALWAYSREPLACE THE BLADE, GUARD AND SPREADERWHEN YOU ARE FINISHED DADOING_
MOLDING CUTTING
Instructions for operating the Molding Head arecontained in a booklet furnished with the MoldingHead
The recommended molding head is listed underRecommended Accessories in this manual
When using the molding head it will be necessary toremove the Blade Guard and Spreader. USE CAUTION
LARGE BLADE DADO ARBORCOLLAR (2" DIA,) HEAD NUT
li
USE FEATHERBOARDS AND PUSH STICKS, etc ASREQUIRED
ALWAYS REPLACE THE BLADE GUARD ANDSPREADER WHEN YOU ARE FINISHED MOLDING
30
-C'CLAMPS FEATHERBOARD
USING FEATHERBOARDS
Featherboards are not employed during non thru-sawing operations when using the miter gauge
Use featherboards for all other non "thru-sawing"operations (when sawblade guard must beremoved) Featherboards are used to keep the workin contact with the fence and table as shown, and tostop kickbacks,,
Add 8 inch high fiat facing board to the fence, thefull length of the fenceMount featherboards to fence and table as shown,so that leading edges of featherboards will supportworkpiece until cut is complete, and the workpiecehas been pushed completely past the cutter(sawbtade, dado head, molding head, etc ) with apushstick, as in ripping,
Before starting the operation (switch "OFF" andcutter befow table surface):
(a) install featherboards so they exert pressureon the workpiece; be positive they are secure,and
(b) Make sure by trial that the featherboards willstop a kickback if one should occur
Replace the sawblade guard as soon as the nonthru-sawing operation is complete,
WORK SUPPORT "C'*CLAMPS
MAmNTENANCEWARNING: TO AVOID INJURY FROMACCIDENTAL START, TURN SWITCH "OFF" ANDREMOVE PLUG FROM POWER SOURCE OUTLETBEFORE MAINTAINING OR LUBRICATING YOURSAW.
Do not allow sawdust to accumulate inside the saw
Frequently blow out any dust that may accumulateinside the saw cabinet and the motor
Frequently clean your cutting tools with CraftsmanGum and Pitch Remover
A coat of automobile-type v,,=x applied to the tablewill hetp to keep the surface clean and allowworkpieces to slide more freely, Treat unplated andunpainted steel parts and surfaces with Sears "StopRust,"
If the power cord is worn or cut, or damaged in anyway, have it replaced immedia[efy
Make sure the teeth of the ANTtKICKBACK pawlsare always sharp To sharpen:
t Identify the dull tooth or teeth Remove bladeguard
2, Rotate pawl toward rear of spreader so that teethare above top of spreader
3 Hold spreader with left hand and place pawl overcorner or workbench
4 Sharpen the dull tooth using a few light strokes ofa fine-cut file
31
LUBRiCATiONThe saw motor bearings have been packed at thefactory with proper lubricant and require noadditional lubrication,
The following parts should be oiled occasionallywith SAE Noo 20 or No, 30 engine oil
1_Elevation guide slot and pivot2, Elevation screw threads,
3., Bevel screw threads (First clean with CraftsmanGum & Pitch Remover.)
4 Bevel and elevation link pivot points
5 Cradle pivot pin bearing points
6, Bearing points in miter gauge and rip fenceThe saw table and other major parts are made ofaluminum and require no special care. A coat ofautomobile-type wax applied to the table will help tokeep the surface clean and allow workpieces to slidemore freely, Treat unplated and unpainted steelparts and surfaces with Sears "Stop Rust "
BEARING POINTS
ELEVATION .7 ISCREW
ELEVATIONLINK
ELEVATIOI'
, GUIDE SLOT IAND PIVOT tl LD
IN CRADLE tl I
32
RECOMMENDED ACCESSORIESITEM CAT. NO,Saw Blades ......................... See Catalog*Molding Head Set ...................... 9-3222Dado Insert ............................ 9-22281Molding Insert ........................... 9-22282Taper Jig ................................. 9-3233Dado Set ............................... 9-32581
ITEM CAT. NO.Steel Legs ............................... 9-22236Retractable Caster Set .................... 9-22221
9-22222"Power Tool Know How Handbook"
Table Saw ............................. 9-2918
*Smaller Diameter Molding Heads cannot be usedbecause they do not provide adequate depth ofcut
The above recommended accessories are currentand were available at the time this manual wasprinted
TROUBLE SHOOTING
WARNING: TO AVOID INJURY FROMACCIDENTAL START, TURN SWITCH "OFF" ANDALWAYS REMOVE PLUG FROM POWER SOURCEOUTLET BEFORE TROUBLE SHOOTING.
TROUBLE SHOOTING -- GENERAL
TROUBLE PROBABLE CAUSE REMEDY
Excessive vibration, t Blade out of balance 1 Discard Blade and use a different blade
1 1 See section 'Miter Gauge"
Sharpen or replace blade
Cannot make square cutwhen crosscutting_
Cuts binds, burns or 1stalls motor when
ripping_ 2
Miter gauge not adjustedproperly
Dull blade with improper
tooth set
Warped board
3 Rip fence not parallelto blade
4 Spreader out of
alignment
1 Stop nuts not properly
adjusted
1 Sawdust on threads of tilt
screw or elevating screw
1. Blade has excessive
wobble
2 Blade collars not installed
properly
1
2
3
4
Make sure concave or hollow side is facing
'down" feed slowly
See "Assembly" section, *Aligning Rip Fence"
See "Assembly" section. "InstallingBlade Guard "
Cut not true at 90 ° t See 'Assembly" section, _Blade Tilt, or
or 45 ° positions, "Squareness of Blade to Table"
Tilt crank and elevating t See "Maintenance and Lubrication" sectioncrank turn hard.
Excessive blade wobble° 1 Replace blade
(Causes oversize kerr
and unsmooth cut) 2 Make sure the _arge collar (2" Dia )is between motor and blade (Installed
before blade)
33
TROUBLE SHOOTING -- MOTOR
NOTE: Motors used on wood-working tools areparticulary susceptible to the accumulation ofsawdust and wood chips and should be blown out or'*vaccummed" frequently to prevent interferenceswith normal motor ventilation
NOTE: The starting relay is a GRAVITY SENSITIVETYPE NEVER TURN THE POWER ON WHILE THESAW IS UPSIDE DOWN AS THIS WILL DAMAGETHE MOTOR
TROUBLE
Excessive noise°
Motor fails to developlull power,. (Poweroutput of motor decreasesrapidly with decrease involtage at motor terminalsFor example, a reductionof 10% in voltage causesa reduction of 19% in
maximum power output ofwhich the motor is capable,white a reduction of 20%
in voltage causesreduction of 36% in
maximum power output )
Motor starts slowly orfails to come up tolull speed.
Motor overheats,
Starting relay in motorwill not operate (Motordoes not come upto full speed°)
Motor stalls (resulting
in blown fuses or tripped
circuit breakers)
Frequent opening offuses or circuit breakers.
PROBABLE CAUSE
1 Motor
1 Circuit overloaded with
lights, appliances andother motors
2 Undersize wires or circuit
too long
3 Generat overloading of power
company facilities (Insome sections of the
country, demand for electrical
power may exceed thecapacity of existing
generating and distribution
systems )4 Incorrect fuses or circuit
breakers in power tine
1 Low voltage-will not trip
relay
2 Starting relay not operating
1 Motor overloaded
2 Improper cooling (Aircirculation restricted
through motor due to
sawdust, accumulatinginside of saw
Burned relay contacts (due
to extended hold-in periods
caused by low line voltage
etc )
2 Saw not in upright position,3. Loose or broken connections
I Starting relay not operating
2 Voltage too low to permitmotor to reach operating
speed3 Fuses or circuit breakers
do not have sufficient
capacity
1 Motor overloaded
2 Fuses or circuit breakers
do not have sufficient
capacity3 Starting relay not operating
(motor does not reach
normal speed)
REMEDY
t
4
2
1
2
Have motor checked by qualified service
technician Repair service is available at
your nearest Sears store
Do not use other appliances or motors on
same circuit when using the saw
Increase wire sizes, or reduce length of wiring
See "Motor Specification and Electrical
Requirements" section
Request a voltage check from the power
company
install correct fuses or circuit breakers
Request a voltage check from the power
companyHave retay replaced,
Do not cut so fast-Feed work slower into blade
Clean out sawdust to provide normal aircirculation through motorSee "Maintenance and Lubrication" section
Have reiay replaced and request a voltage check
from the power company
2 Place saw in upright position3 Have wiring checked and repaired
I Have relay replaced
2 Request a voltage check from the powercompany
3 Install proper size fuses or circuit breakers
1 Don't cut so fast-Feed work slower into blade
2 lnstalt proper size fuses or circuit breakers
3 Have relay replaced
34
REPAIR PARTSPARTS LIST FOR CRAFTSMAN 8 INCH DIRECT DRIVE TABLE SAW
MODEL NO. 113.221611
8
\
i
FIGURE 1 - GUARD ASSEMBLY 62935
Always Order by Part Number - Not by Key Number
M
Key
12345678
Part Description
629166291162519i62921iSTD551025i62561i62902i455734i
Link, GuardGuardSpring, PawlPin
*Washer, 17/64 x 1/2 x 1/32PawlBlade, SpreaderPin, Roll 1/8 x 3/4
*Standard Hardware Item - May be Purchased Locally
35
f,,,t¢P,
PARTS LiST FOR CRAFTSMAN 8 lINCH DIRECT DRIVE TABLE SAWMODEL NO. 113.221611
8 9
\\ 65
10 1t
68
.i
J
//
12
t5
I
13
24
50 51 52
42
55
47
41-41.40 46
45
\64 63
PARTS LIST FOR CRAFTSMAN 8 INCH DIRECT DRIVE TABLE SAWMODEL NO. 113.221611
FIGURE 2
(eyNo.H,=
t2
34567
8
9101112131415
161718t9202'1
2223
24
25262728293031
3233343536
37
383940
PartNo.
62905ST D601 'I03
624366262581607562908805297_9
]05297-1
_293l62915
iSTD600805629096293762924STD601105
62936624426025680370967085STD510603
629136292562938
6293562642STD54!02562809STD551225STD541625]0074
}TD551012STD54t0256264360314_420417
ITD611005
816072816073STD551037
Description
Bracket, Cradle*Screw, Hex Washer Hd
Type "T" 10-32 x 3/8NutHangerRod, CradleExtension, Table LHScrew, Socket Fiat Hd
1/4-20 x 5/8Screw, Flat Hd5/16-18 x 1-1/4
TableInsert, Table
*Screw, Pan Hd 8-32 x 1/2Extension, Table R.HFence Assy, Rip (See Fig 3)Plate, Switch
*Screw, Pan Hd. CrossRecess Type "T" 10-32 x 1/2
Lead AssemblySwitch, LockingKey, LockingConnector, WireCord with Plug
*Screw, Pan Rec..Type "T" 6-32 x 3/8
Housing, SwitchoRelay
Gauge Assembly, Miter(See Fig. 4)
Guard Assembly (See Fig 1)Support, Spreader
*Nut, Square 1/4-20Bracket, Spreader
*Lockwasher, External 1/4-20*Nut, Wing 1/4-20Screw, Socket Set
1/4-20 x 7/8*Washer, 17/64 x 9/16 x 3/64*Nut, Hex 1/4-20Clamp, SpreaderScrew, Truss Hd. 1/4-20 x 5/8Screw, Washer Type "T"
1/4-20 x 5/8*Screw, Pan Rec Type "AB"
No 10 x 1/2Panel, Frontindicator, Bevel
*Washer, 380 x 47/64 x 1/16
*Standard Hardware item - May be purchasedlocally.
1"Stock Item- May be secured through the HardwareDepartment of most Sears Retail Stores andCatalog Order House,
"klf this part is removed, discard and replace with anew Push Nut
Key PartNo. No.
4I 6024042 6291243 STD55120844 STD51080345 }290146 81463847 STD52250648 STD55112549 81607150 806752W
51 6054052 6291953 6291754 6292355 81607656 941492057 16038858 81466359 6509360 629006t 60548
#
62 6298963 6054I
64 6054665 6054566 1899267 6054768 6362
69 6249870 6299271 628567273747576777879
STD5410256053962922STD551025814770354063062STD551210507545
507546
SP5022
Description,=,
t_Nut, Push 3/8Handwheel, 3-5/8
*Lockwasher, No 8*Screw, Pan 8-32 x 3/8BasePlate, Thrust
*Screw, Hex 1/4-20 x 5/8*Lockwasher, 1/4Bracket Lead ScrewScrew, Pan Hd Type "T"
10-32 x 1-1/8Ring, Retaining 11/16Nut, ElevationLinkPin, GuideShaft, TiltWasher, t7/64 x 5/8 x 1/16Nut, Self-ThreadingShaft, ElevationClip, WireBaffleScrew, Hex Washer Type "T"1/4-20 x 3/8
Bracket, Lead ScrewScrew, Hex Locking1/4-20 x 3/4
Washer, SpringWasher, Nylon
1:Blade, 8"Collar, OuterNut, Saw ArborCollar, InnerCradle
oMotor*Nut, Hex 1/4-20Ring, Retaining 1/4Pin, Guide
*Washer, 17/64 x 1/2 x 1/32LinkWrench, ArborWrench, Shaft
*Lockwasher Ext, #10Bag of Loose Parts
(Not Illustrated)Bag of Loose Parts(Not Illustrated)
Owners Manual(Not Illustrated)
QRelay must accompany motor when motor isreturned for service. Any attempt to repair thismotor may create a hazard unless repair is done bya qualified service technician Repair service isavailable at your nearest Sears Store.
37
PARTS LIST FOR CRAFTSMAN 8 INCH DIRECT DRIVE TABLE SAWMODEL NO. 113,221611
7 6
/5
FIGURE 3 - RIP FENCE ASSEMBLY 62937
m,
KeyNo.
12
34567
Part
No, Description
62906STD522505
6298562482STD5412316054362939
Channel, Fence*Screw, Hex Hd, Sems
1/4-20 x 1/2Head, FenceKnob, t-1/4 Dia
*Nut, Hex ,Jam 5/16-18Screw, Truss Hd 5/16-!8 x 2Clip, Shoe
*Standard Hardware Item - May be Purchased Locally
38
PARTS LIST FOR CRAFTSMAN 8 INCH DIRECT DRIVE TABLE SAWMODEL NO. 113.221611
7
FIGURE 4 - MITER GAUGE ASSEMBLY 62938
Key PartNo. No.
1 621762 STD5510103 621734 621755 STD5108036 387247 605448 62927
Description
Knob, Miter Gauge*Washer, I3/64 x 5/8 x 1/32Gauge, MiterPin, Miter Pivot
*Screw, Pan Hd 8-32 x 3/8PointerSpacerRod, Miter Gauge
*Standard Hardware Item = May be Purchased Locally
39
SERVICE
MODEL NO.113.221611
SAW WITHTABLE EXTENSIONS
HOW TO ORDER
REPAIR PARTS
8 iNCH DIRECT DRIVETABLE SAW
Now that you have purchased your 8 inch direct drive tablesaw should a need ever exist for repair parts or service,simply contact any Sears Service Center and most Sears,Roebuck and Co stores Be sure to provide all pertinentfacts when you call or visit.
The model number of your 8 inch direct drive table saw willbe found on a plate attached to your saw, at the rear of thebase
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THEFOLLOWING INFORMATION:
PART NUMBER
MODEL NUMBER113o221611
PART DESCRIPTION
NAME OF ITEM8 INCH DIRECT DRIVETABLE SAW
All parts listed may be ordered from any Sears ServiceCenter and most Sears stores, If the parts you need arenot stocked locally, your order will be electronicallytransmitted to a Sears Repair Parts Distribution Centerfor handling.
Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.Part No SP5022 Form No.. SP5022-2 Printed in US.A. 7/87