cpmca & southern california pipe trades d.c. 16 annual ... · 8/31/2019 · cal fall...

CPMCA & SOUTHERN CALIFORNIA PIPE TRADES D.C. 16 Annual Journeymen Upgrade Training (JUT)

10-hour/15-hour/20-hour

of 12 Rev. 2/6/18

The Master Agreement (2017-2026) for the Plumbing and Piping Industry of Southern California

between California Plumbing and Mechanical Contractors Association and Southern California

Pipe Trades District Council No. 16 of the United Association states 5.9.1 Effective September 1,

2018, all Book 1 and Book 2 Journeymen must annually complete ten (10) hours of approved

journeymen training as a condition of new or continuing employment. Effective September 1,

2020 the annual training requirement shall increase to fifteen (15) hours. Effective September

1, 2022 the annual training requirement shall increase to twenty (20) hours. The Union and

Contractors Association working with the Southern Pipe Trades Apprentice and Journeymen

Training Trust shall establish approved classes, seminars, instruction, and other types of training

for purposes of satisfying the requirements hereunder.

• Effective September 1, 2018 to August 31, 2019 = 10 hours minimum training hours

must be completed by August 31, 2019 (Journeymen Training hours from the approved

list completed from January 1, 2018 to August 31, 2018 will be accepted for the September

1, 2018 to August 31, 2019 year.) (Annual means September 1 to August 31)


must be completed by August 31, 2020 (For this year only, any hours over the first 10

hours completed from January 1, 2018 will be accepted towards hours for the September

1, 2019 to August 31, 2020 year.)


must be completed by August 31, 2021.





• Effective September 1, 2023 to August 31, 2024 = 20 hours minimum training

hours must be completed by August 31, 2024.





The following courses have been approved by Labor and Management for the required annual

journeymen upgrade training. (Note: Actual course hours may vary from the approved credit

hours. Course hours may be more hours than the annual required hours; however, excess hours



of 12 Rev. 2/6/18

over the 10 hours completed from January 1, 2018 to August 31, 2019 will only be allowed to

carry over to the 2019/2020 fiscal year.)

Members must attend all hours of training, pass the course with a 70% or better, and pass the UA

weld test when taking a UA weld test toward their required annual JUT hours. Members taking

the same course/courses each year will not qualify for the required minimum annual training

hours. The same course/courses may be retaken when a certification is due to expire within that

year. Courses offered through A&J must be requested on A&J website at www.ajtraining.org.

Courses offered through CPMCA must be requested on CPMCA website at www.cpmca.org.

• Example of compliance with the MLA annual JUT requirement.

o Attending, completing and passing an 11-hour Cal OSHA 10 course from January

1, 2018 to August 31, 2019 will satisfy the required 10 hours that must be

completed by August 31, 2019. 1-hour (11th hour) can be carried over towards

satisfying the September 1, 2019 to August 31, 2020 year 10-hour requirement.

o Attending, completing and passing a 32-hour NITC Fitter Certification course

from September 1, 2020 to August 31, 2021 will satisfy the required 15 hours that

must be completed by August 31, 2021. The 16th to 32nd hour of the 32-hour

course will not carry over to the September 1, 2021 to August 31, 2022 year 15-

hour requirement.

• Example of non-compliance with the MLA annual JUT requirement.

o Notification sent to members home local and Contractor/Employer. Member will

be removed from employment with Contractor/Employer and will be ineligible for

Book 1 and Book 2 list.

Procedure for submitting training outside of approved course list:

• Journeyman must submit an email to the Journeyman Upgrade Administrator (JUA) on any

course they may wish to submit outside of those listed on the approved course list. These

requests will be evaluated by the JUA to determine if the training is equivalent. If a course

has already been recently taken, the JUA will confirm that the recent training was

completed and submits their finding to Journeyman Upgrade Training (JUT) committee

for approval. Course must have been taken and completed after January 1, 2018.

o Example of such courses may include, but not limited to, college course in

estimating, building construction systems and codes, or industrial Relations in

Construction. The JUA understands that various trades association have training

session that may have CEU’s that qualify as approved courses. These may also be

submitted to the JUA for evaluation. Example of such course may include NFPA 99

4-hour Online Medical Gas Training, ASME Boiler & Pressure Vessel Certification or

AWS’s Understanding Welding Symbols course.

http://www.ajtraining.org/

http://www.cpmca.org/



of 12 Rev. 2/6/18

o Example of course that would not qualify would be those such as, Introduction to

Philosophy, Childcare, or World History. Course must pertain in some manner to

the piping industry.

• Courses offered at a Local Union or Contractors Office/Shop must pre-approved by the

JUT Committee. All requests must be emailed to the JUT Administrator, including

description of course/presentation, location, beginning and ending time and

instructor/presenter. After completion of class/presentation, a legible list of members

names, UA ID number, phone number and signature must be submitted to the JUT

Administrator via email. The JUT Administrator may need to be onsite during training to

confirm training has been completed.

A&J Journeymen Courses

Advanced Instrumentation 136 hours

Asbestos Awareness 16 hours

Asbestos Awareness Recertification 8 hours

Backflow Prevention 48 hours

Basic Computers 32 hours

Basic Instrumentation/EPRI Level I 64 hours

CAD I 32 hours

CAD II 32 hours

CAD III 32 hours

Cal OSHA 10 11 hours

Cal OSHA 30 32 hours

Competent Person 8 hours

Confined Spaces 16 hours

Crane Signal Person 32 hours

Crane Signal Person Recertification 8 hours

EPRI Level II Certification 64 hours

First Aid/CPR 8 hours

Forklift Training 8 hours

Green Awareness 16 hours

Green Awareness Systems Awareness Certification 24 hours

High Hazard Facility Safety Training 20 hours

Industrial Pipefitter Refinery 24 hours

L.A. Structural Steel 32 hours

Medical Gas Installer 32 hours

Medical Gas Renewal 4 hours

MSHA 24 hours

MSHA Refresher 8 hours

NITC Fitter Certification 32 hours

NITC Plumber Certification 32 hours

Orbital Welding/Clean Room 32 hours

Pipeline Safety 16 hours



of 12 Rev. 2/6/18

A&J Journeymen Courses (continued)

Rigging Techniques 32 hours

S&R – Basic Electricity Part II 8 hours

S&R – Basic Heating (Wall & Floor Furnace, Direct Vent) Installation,

Troubleshooting and Repair

8 hours

S&R – Faucet & Shower Valve Installation and Repair 8 hours

S&R – Pumps Installation & Troubleshooting 8 hours

S&R – Residential Tank Water Heaters 8 hours

S&R – Sewer Machines, Cameras & Line Locations 8 hours

S&R – Takagi Tankless Water Heater Training & Basic Electricity Part I 8 hours

S&R – Tankless Water Heater Installation & Repair 8 hours

S&R – Toilets 8 hours

S&R – Water Heater Repair 8 hours

Trimble & Sokkia Robotic Total Station Training 24 hours

Tube Bending 16 hours

UA Foreman 56 hours

UA Rigging Certification 66 hours

UA Rigging Recertification 4 hours

Valves Certification 40 hours

Valves Certification Refresher 8 hours

Clicksafety Courses

Advanced Safety Training

100% Fall Protection 45 minutes

A3 OSHA Recordkeeping & Reporting 60 minutes

Accident Prevention in Heavy Construction 30 minutes

Alcohol & Substance Abuse 60 minutes

Asbestos Hazards 35 minutes

Confined Spaces in Construction: An Introduction 75 minutes

Construction Jobsite Safety Orientation R2 60 minutes

Control of Hazardous Energies 30 minutes

Crane Safety Basics 80 minutes

Dust Disturbance and Mitigation 40 minutes

Electric Hazard Recognition and Control 45 minutes

Electrical Safety R2 40 minutes

Emergency Action/Response 60 minutes

Ergonomics 45 minutes

Excavation Safety R2 45 minutes

Fall Protection Equipment 50 minutes

Fall Protection in Construction 90 minutes

Fire Prevention 60 minutes

Focus 4 Fatality Prevention: Caught Between 60 minutes

Focus 4 Fatality Prevention: Electrocution Hazards 120 minutes

Focus 4 Fatality Prevention: Fall Hazards 120 minutes



of 12 Rev. 2/6/18

Clicksafety Courses (continued)

Focus 4 Fatality Prevention: Struck By 60 minutes

Forklift Hazards 60 minutes

Ground Fault Protection in Construction R2 35 minutes

Hand and Power Tools R2 50 minutes

Hazardous Waste 30 minutes

Heat Stress 20 minutes

Introduction to NFPA 70E 45 minutes

Introduction to OSHA – Construction 75 minutes

Introduction to OSHA – General Industry 75 minutes

Lead Hazards 15 minutes

Materials Handling 40 minutes

Mold – OSHA Position 50 minutes

Molds 45 minutes

Motorized Mobile Platforms 45 minutes

Noise and Hearing Protection 15 minutes

Other Construction Health Hazards 50 minutes

Power Tool Use and Guarding 45 minutes

PPE Common R2 60 minutes

PPE Specialized R2 45 minutes

Respiratory Protection 50 minutes

Rigging R2 45 minutes

Safety and Health During Disaster Recovery R2 35 minutes

Scaffold Erection Guidelines 30 minutes

Scaffold User Guidelines R2 30 minutes

Signs, Signals and Barricades 30 minutes

Silica Exposures in Construction R2 60 minutes

Slips, Trips and Falls 30 minutes

Soils Analysis and Classification 50 minutes

Stairways and Ladders R2 45 minutes

Subpart C – Construction General Safety 60 minutes

Subpart D – Construction Health Hazards 60 minutes

Subpart O – Motor Vehicles, Mechanized Equipment 75 minutes

Trenching and Excavation 25 minutes

Trenching and Excavations – Practical Applications 50 minutes

Tubular Welded Frame Scaffold Erectors R2 60 minutes

Welding/Hot Work 35 minutes


California

Cal Confined Spaces for Construction 45 minutes

Cal Crane Safety Basics 50 minutes

Cal Electrical Hazard Recognition/Control 45 minutes

Cal Electrical Hazards 30 minutes



of 12 Rev. 2/6/18


Cal Fall Protection 40 minutes

Cal Fall Protection Awareness 15 minutes

Cal Fire Prevention 60 minutes

Cal Fire Prevention Awareness 15 minutes

Cal Flagger 30 minutes

Cal Ground Fault Protection 30 minutes

Cal Hand and Power Tools 60 minutes

Cal IIPP 15 minutes

Cal Materials Handling 45 minutes

Cal Personal Protection Equipment Awareness 25 minutes

Cal Personal Protective Equipment R2 75 minutes

Cal Practical Trenching 60 minutes

Cal Scaffold Erection 30 minutes

Cal Scaffold Safety Awareness 15 minutes

Cal Scaffold Use 30 minutes

Cal Stairs and Ladders 45 minutes

Cal Trenching and Excavation 30 minutes

Cal/OSHA for Construction 30 minutes

Cal/OSHA Heat Illness R2 60 minutes

Cal/OSHA, An Introduction 30 minutes

Certificate or OSHA Authorized

Asbestos Awareness in Construction 120 minutes

Asbestos Awareness in General Industry 120 minutes

Asbestos Awareness in Schools 120 minutes

Cal/OSHA 10 Hour Construction Safety Course 600 minutes

Forklift Operator Certification 90 minutes

HAZWOPER 16-Hour 480 minutes



HAZWOPER 8-Hour Refresher 2015 480 minutes

HAZWOPER 8-Hour Supervisor 480 minutes

Lead Awareness in Construction 90 minutes

Lead Awareness in General Industry 90 minutes

OSHA 10 Construction Course 600 minutes

OSHA 10 Hour General Industry Training Course 600 minutes

OSHA 10 Road Construction 600 minutes

OSHA 10 Spanish 600 minutes

OSHA 30 Construction Course 1800 minutes

Rough Terrain Forklift Operator Certification 90 minutes

Department of Transportation (DOT)

Drug and Alcohol Training for Supervisors 120 minutes



of 12 Rev. 2/6/18


General Industry

100 Questions on Electrical Safety 180 minutes

13 Carcinogens 15 minutes

Air Contaminants 20 minutes

Ammonia Awareness R2 20 minutes

Asbestos 10 minutes

Back Injury Prevention and Safe Lifting Techniques 30 minutes

Cal/OSHA Heat Illness Prevention for Workers 40 minutes

Compressed Gas Cylinder Safety Awareness R2 25 minutes

Confined Spaces Awareness R2 30 minutes

Container Labeling R2 10 minutes

Control of Hazardous Energies, COHE R2 20 minutes

Electrical Safety and LOTO 60 minutes

Exit Routes, EAP/Fire Prevention Plans 60 minutes

Fed/OSHA Heat Illness Prevention for Workers 60 minutes

Flammable and Combustible Liquids 50 minutes

Flammable and Combustible Liquids R2 50 minutes

Hazard Communication Advanced (HazCom) 60 minutes

Hazard Communication Awareness (HazCom) 25 minutes

Hazard Communication for Managers & Supervisors 60 minutes

Industrial Hygiene Awareness R2 15 minutes

Inorganic Arsenic 10 minutes

Ionizing Radiation 20 minutes

Introduction to NFPA 70E 2015 40 minutes

Job Hazard Analysis 30 minutes

Ladder Safety Training 45 minutes

Lead 10 minutes

Machine Guarding 60 minutes

Materials Handling and Storage, General Industry 50 minutes

Noise and Hearing Conservation 20 minutes

Personal Protective Equipment 50 minutes

Portable Fire Extinguishers 15 minutes

Respiratory Protection Awareness R2 20 minutes

Subpart Z – Toxic and Hazardous Substances 265 minutes

Walking and Working Surfaces 30 minutes

Worker Right to Know 10 minutes

Workplace Violence 25 minutes

General Safety Awareness

Confined Spaces in Construction Awareness 20 minutes

Crystalline Silica R2 10 minutes

Electrical Safety Awareness R2 10 minutes

Emergency Action Planning Awareness 10 minutes

Employer/Employee Responsibility 10 minutes



of 12 Rev. 2/6/18


Ergonomics Awareness 10 minutes

Fall Protection Awareness R2 15 minutes

Fire Prevention Awareness 10 minutes

General Housekeeping on the Jobsite 10 minutes

Introduction to Heavy Construction Safety & Health 30 minutes

Introduction to OSHA’s Focus Four Hazards R2 25 minutes

Jobsite Safety Orientation R2 20 minutes

Ladder Safety Awareness R2 10 minutes

Power Tool Safety Awareness R2 10 minutes

PPE Awareness R2 10 minutes

Scaffold Safety Awareness R2 10 minutes

Trenching and Excavation Awareness R2 15 minutes

Working Around Mobile Equipment R2 10 minutes

Working Safely with Electricity 20 minutes

Human Resource

Sexual Harassment for Non-California Employees 60 minutes

Sexual Harassment for Non-California Managers 180 minutes

Management Courses

Alcohol and Substance Abuse for Supervisors 75 minutes

Competent Person, Excavations 170 minutes

Competent Person, Fall Protection 230 minutes

Conducting Tailgate Meetings 40 minutes

Construction Spanish for Supervisors 60 minutes

Contractor’s Safety and Health Program 60 minutes

Health and Leadership Safety 240 minutes

OSHA Compliance Basics 60 minutes

Suspicious Mail, Anthrax and Other Concerns 30 minutes

The Competent Person 45 minutes

Spanish

C1 Cal Fall Protection Awareness 15 minutes

C1 Cal Fire Prevention 15 minutes

C1 Cal PPE Awareness 25 minutes

C1 Cal Scaffold Safety Awareness 15 minutes

C1 Cal/OSHA for Construction 30 minutes

C1 Crystalline Silica Exposure 10 minutes

C1 Introduction to OSHA’s Focus Four 25 minutes

C1 Working Safely with Electricity 20 minutes

C2 Alcohol and Substance Abuse 30 minutes

C2 Noise and Hearing Protection 15 minutes

Cal/OSHA Heat Illness R2 30 minutes

Compressed Gas Cylinder Safety Awareness 25 minutes

Confined Space Entry 40 minutes

Confined Spaces Awareness 15 minutes



of 12 Rev. 2/6/18


Control of Hazardous Energies 30 minutes

Crane Safety Basics 45 minutes

Electrical Hazards 30 minutes

Electrical Safety Awareness 15 minutes

Emergency Action Planning Awareness 15 minutes

Employer/Employee Responsibility 15 minutes

Ergonomics Awareness 15 minutes

Fall Protection Awareness 15 minutes

Fall Protection in Construction 90 minutes

Fire Prevention 60 minutes

Fire Prevention Awareness 15 minutes

Flammable & Combustible Liquids 25 minutes

Ground Fault Protection in Construction 30 minutes

Hazard Communication Advanced 60 minutes

Hazard Communication Awareness 20 minutes

Heat Stress 40 minutes

Jobsite Safety Orientation Awareness 15 minutes

Ladder Safety Awareness 15 minutes

Materials Handling 45 minutes

OSHA: An Introduction 45 minutes

Personal Protective Equipment 75 minutes

Personal Protective Equipment Awareness 20 minutes

Power Tool Awareness 15 minutes

Power Tools Use and Guarding 60 minutes

Rigging 30 minutes

Scaffold Erection Guidelines 30 minutes

Scaffold Safety Awareness 15 minutes

Scaffold User Guidelines 30 minutes

Stairways and Ladders 45 minutes

Trenching and Excavation Awareness 15 minutes

Trenching and Excavations 25 minutes


Working Around Mobile Equipment 15 minutes

CPMCA Courses

Computer Skills & Technology

Bluebeam Revu 2017 7 hours

MS Excel 2016 – Part 1 7 hours



MS Project 2016 – Part 1 7 hours

MS Project 2016 – Part 2 7 hours



of 12 Rev. 2/6/18

CPMCA Courses (continued)

Foreman

Six Habits of the Highly Effective Foreman 7 hours

Management

California Construction Law Essentials 4 hours

People Management/Skills

Dealing with Difficult People in Construction 6 hours

Mastering the 8 Tenets of Values-Based 6 hours

Project Management

Maximizing Productivity Utilizing a Best-In-Class Prefab System 6 hours

Project Engineering Basics in Construction Project Manager/Foreman Training

Series

6 hours

Project Managers Impact on Financial Outcomes 6 hours

Project Manager/Foreman Training Series

Project Manager/Foreman Training Series 1 & 2 Day 1: 7 hours

Day 2: 4 hours


Day 2: 4 hours


Day 2: 4 hours

Sales/Service/Safety

Sexual Harassment Prevention Training 2 hours

UA Weld Tests qualify for the maximum number of hours as indicated on the weld test

specification page for each test.

Weld Test Process Pipe Coupon Size Wall

Thickness Filler Metals Special Notes

Max Time to

Complete

SS-1 Solder 1 1/2" Tube ASTM B32 Solder Solder Test 1-hour

UA-R1 GTAW 2" Sch. 80 .218" ER309 Requalification Test 2-hrs

UA-R2 SMAW 6" Sch. 80 .432" E6010 / E7018 Requalification Test 3-hrs

UA-R3 GTAW 2" Sch. 80 .218" ER70S-6 Requalification Test 2-hrs

UA-1 SMAW 6" Sch. 40 .280" E6010 Downhill Welding 2-hrs

UA-2 SMAW 6" Sch. 40 .280" E6010 / E7018 — 2-hrs

UA-3A GTAW & SMAW 6" XXS .864" ER80S-B6 / E8018-B6 5% Chrome Test 6-hrs

UA-5 GTAW & SMAW 6" Sch. 40 .280" ER70S-2 / E7018 — 2-hrs

UA-6 GTAW & SMAW 2" XXS .436" ER70S-2 / E7018 / E309 — 6-hrs

UA-8 SMAW 2" Sch. 80 .218" E6010 / E7018 — 3-hrs

UA-9T GTAW & SMAW 6" XXS .864" ER70S-2 / E7018 — 6-hrs



UA-12 GMAW-S 6" XXS .864" ER70S-6 — 5-hrs

UA-12W GMAW-S 6" Sch. 80 .432" ER70S-3 or 6 — 4-hrs

https://uanet.org/pdfPassThrough.asp?file=uass1.pdf

https://uanet.org/pdfPassThrough.asp?file=uar1.pdf



https://uanet.org/pdfPassThrough.asp?file=ua1.pdf


https://uanet.org/pdfPassThrough.asp?file=ua3a.pdf




https://uanet.org/pdfPassThrough.asp?file=ua9t.pdf




https://uanet.org/pdfPassThrough.asp?file=ua12w.pdf



of 12 Rev. 2/6/18

UA Weld Tests (continued)

UA-13 GTAW 3/8" Sch. 10 .065" none Manual Fusion 2-hrs

UA-14 GTAW 2" Sch. 10 .109" none Manual Fusion 2-hrs

UA-15 GTAW 2" Sch. 80 .218" ER70S-2 — 2-hrs

UA-16 GTAW 1/2" Sch. 80 .147" ER70S-2 Very small diameter 3-hrs

UA-17 GMAW & FCAW 6" XXS .864" ER70S-6 / E71-T1 — 5-hrs

UA-17W GMAW & FCAW 6" Sch. 80 .432" ER70S-6 / E71-T1 — 4-hrs

UA-18 SMAW 2" Sch. 160 .344" E7018 — 4-hrs

UA-18A GTAW 0.750" O.D. .065" none Automatic Orbital Welding 3-hrs

UA-19 SMAW 2" Sch. 160 .344" E6010 / E7018 — 4-hrs

UA-20 FCAW 6" Sch. 80 .432" E71-T1 Using Backing Ring 3-hrs

UA-21 SMAW 2" XXS .436" E6010 / E7018 — 3-hrs

UA-22 GTAW & SMAW 2" XXS .436" ER70S-2 / E7018 — 3-hrs

UA-23 SMAW 6" XXS .864" E6010 / E7018 — 6-hrs

UA-24 SMAW 6" Sch. 120 .562" E6010 / E7018 — 5-hrs

UA-25 GTAW 2" XXS .436" ER70S-2 — 5-hrs

UA-26 GTAW & SMAW 2" Sch. 160 .344" ER70S-2 or 3 / E7018 — 3-hrs

UA-27 GMAW 6" Sch. 80 .432" ER70S-6 Root-down / Balance-up 4-hrs

UA-28 SMAW 6" Sch. 80 .432" E6010 / E7018 — 4-hrs

UA-29 SMAW 6" Sch. 80 .432" E6010 / E7018 Restricted Access Test 4-hrs

UA-30 GMAW& FCAW 6" Sch. 80 .432" ER70S-6 / E71-T1 IG Rolled Test 2-hrs

UA-31B GTAW 6" Sch. 40 .280" ER5356 Aluminum Test - chill ring 3-hrs

UA-31J GTAW 6" Sch. 40 .280" ER5356 Aluminum Test - J Bevel 3-hrs

UA-32 SMAW 6" Sch. 80 .432" E6010 — 4-hrs

UA-33 GTAW 2" Sch. 40 .154" ER NiCrMo-10 Nickel Alloy Test 3-hrs



UA-36 GMAW & FCAW 2 3/4" O.D. .625" ER70S-6 / E71-T1 3-hrs

UA-37 GTAW 6" Sch. 120 .562" ER70S-6 Machine Welding 5-hrs


UA-39 GMAW 6" Sch. 80 .432" ER308Si IG Rolled Test 4-hrs

UA-41 GTAW 2" Sch. 80 .218" ER309 Stainless Test 3-hrs

UA-42 GTAW & SMAW 2" XXS .436" ER309 / E309-16 Stainless Test 4-hrs

UA-43 GTAW & SMAW 6" XXS .864" ER309 / E309-16 Stainless Test 6-hrs

UA-44 GTAW 10" Sch. 100 .719" ER309 Narrow Groove Test 7-hrs

UA-45 GTAW 2" Sch. 10 .109" ER308 Stainless Test 3-hrs

UA-46 SMAW 2" Sch. 160 .344" E309-17 or 16 Stainless Test 4-hrs

UA-47 GTAW 6" Sch. 80 .432" ER70S-6 Machine Welding 5-hrs

UA-48 GTAW 10" Sch. 100 .719" ER309 Remote Video control 6-hrs

UA-49 GTAW 6" Sch. 80 .432" ER70S-2 & ER70S-6 Manual & Machine Welding 6-hrs

UA-50 Brazing 3/4" Tube .045" BCuP 2 thru 7 Manual Torch Brazing 2-hrs

UA-51 Brazing 1 1/2" Tube .060" BCuP 2 thru 7 Manual Torch Brazing 2-hrs

UA-52 Brazing 1 1/2" Tube .060" BCuP 2 thru 7 Brazer Qual Renewal Test 1-hrs

UA-60 SMAW 2 3/4" O.D. .625" E6010 / E7018 5-hrs

UA-61 GTAW & SMAW 2 3/4" O.D. .625" ER309 / E309-16 Stainless Test 5-hrs






https://uanet.org/pdfPassThrough.asp?file=ua17w.pdf


https://uanet.org/pdfPassThrough.asp?file=ua18a.pdf













https://uanet.org/pdfPassThrough.asp?file=ua31b.pdf

https://uanet.org/pdfPassThrough.asp?file=ua31j.pdf

























of 12 Rev. 2/6/18

UA Weld Tests (continued)

UA-62 GTAW & SMAW 2 3/4" O.D. .625" ER70S-2 / E309-16 5-hrs

UA-63 GTAW & SMAW 2 3/4" O.D. .625" ER70S-2 / E7018 5-hrs

UA-64 SMAW 2 3/4" O.D. .625" E7018 5-hrs

UA-66 GTAW 2 3/4" O.D. .625" ER NiCr-3 Nickel Alloy Test 5-hrs

UA-67 GTAW 2 3/4" O.D. .625" ER70S-2 5-hrs

UA-68 SMAW 2 3/4" O.D. .625" E6010 / E7018 Root-down / Balance-up 5-hrs

UA-69 GTAW & SMAW 2 3/4" O.D. .625" ER70S-2 / E7018 4-hrs

UA-70 SMAW 2" pipe & 3/16"

plate .154" E7018 Structural Steel Fillet Weld Test

2-hrs

UA-71 GMAW 6" Sch. 80 .432" ER70S-3 or 6 Short Arc Root/Spray or Pulse Fill 4-hrs

UA-72 GMAW 6" Sch. 80 .432" ER70S-2 or 3 IG Rolled Test 3-hrs

UA-73 SMAW 6" Sch. 80 .432" E6010 / E7018 Flip Flop Test (2G & 5G) 4-hrs

UA-74 GTAW 6" Sch. 10 .134" ER308L or ER316L Stainless Orbital Machine Welding 5-hrs

UA-75 GTAW 6" Sch. 10 .134" ER308L or ER316L Stainless Orbital Machine Welding 5-hrs

UA-76 SMAW 2" XXS .436" E6010 / E7018 Two Coupons (2G & 5G) 4-hrs

UA-77 GTAW & SMAW 10" Sch. 160 1.125" ER70S-2 / E7018 LU responsible for coupon costs 8-hrs

UA-78 GTAW & SMAW 2 3/4" O.D. .625" ERNiCr-3 / ENiCr-3 Nickel Alloy Test 4-hrs

UA-79 GMAW 6" Sch. 80 .432" ER70S-3 or 6 90% Argon / 10% CO2 3-hrs

UA-80 GTAW 6" Sch. 80 .432" ER70S-6 or ER309 "Tip-Tig" Hot Wire Process 3-hrs

UA-81 SMAW 2" XXS .436" E7010-A1 / E7018-A1 — 3-hrs

UA-85 GMAW 2 3/4" O.D. .625" ER70S-6 90% Argon / 10% CO2 4-hrs

UA-86 GTAW & FCAW 6" Sch. 80 .432" ER70S-2 or E71T-1 IG Rolled Test 2-hrs

UA-87 SMAW 6" Sch. 40 .280" E6010 / E7018 Two Coupons (2G & 5G) 4-hrs

UA-91 GTAW & SMAW 2" XXS .436" ER90S-B9 / E9018-B9 9% Chrome Test 5-hrs

UA-92 GTAW 2" Sch. 40 .154" ERTi-2 LU responsible for coupon costs 3-hrs


UA-94 GTAW & SMAW 2 3/4" O.D. .625" ER70S-2 / E7018 Restricted Access Test 5-hrs

UA-99 SMAW 6" Sch. 80 .432" E6010 / E7018 Two Coupons (2G & 5G) 4-hrs

UA-100 SMAW 4" Sch. 80 .337" E6010 / E7018 2G Only Test 4-hrs

UA-101 GMAW & FCAW 6" XXS .864" ER70S-6 / E71T-1 Flip-Flop Test (2G & 5G) 5-hrs

UA-102 GMAW & FCAW 8" Sch. 40 .322" ER308LSi /E308LT1 Flip-Flop Test (2G & 5G) 3-hrs

UA-103 GMAW & FCAW 6" Sch. 80 .432" ER70S-6 / E71T-1 Two Coupons (2G & 5G) 3-hrs


























https://uanet.org/pdfaccess/pdf/ua94.pdf






cpmca & southern california pipe trades d.c. 16 annual ... · 8/31/2019 · cal fall...

Documents