course 02n arches - web.itu.edu.trweb.itu.edu.tr/ustunda1/course/slides_10.10.2013.pdf · funicular...
TRANSCRIPT
Arches
Arches can be used to reduce the bending moments inlong-span structures. Essentially, an arch acts as aninverted cable, so it receives its load mainly incompression although, because of its rigidity, it must alsoresist some bending and shear depending upon how it isloaded and shaped.
Arches
In particular, if the arch has a parabolic shape and it issubjected to a uniform horizontally distributed verticalload, then only compressive forces will be resisted by thearch. Under these conditions the arch shape is called afunicular arch because no bending or shear forces occurwithin the arch.
Arches
Depending on its uses, several types of arches can beselected to support a loading
fixed arch tied arch
two-hinged arch three-hinged arch
Arches
A fixed arch is often made from reinforced concrete.Although it may require less material to construct thanother types of arches, it must have solid foundationabutments since it is indeterminate to the third degreeand, consequently, additional stresses can be introducedinto the arch due to relative settlement of its supports.
fixed arch
Arches
A two-hinged arch is commonly made from metal ortimber. It is indeterminate to the first degree, andalthough it is not as rigid as a fixed arch, it is somewhatinsensitive to settlement. We could make this structurestatically determinate by replacing one of the hinges witha roller. Doing so, however, would remove the capacity ofthe structure to resist bending along its span, and as aresult it would serve as a curved beam, and not as anarch.
two-hinged arch
Arches
A three-hinged arch which is also made from metal ortimber, is statically determinate. Unlike staticallyindeterminate arches, it is not affected by settlement ortemperature changes.
three-hinged arch
Arches
If two and three-hinged arches are to be constructedwithout the need for larger foundation abutments and ifclearance is not a problem, then the supports can beconnected with a tie rod.A tied arch allows the structure to behave as a rigid unit,since the tie rod carries the horizontal component of thrustat the supports. It is also unaffected by relative settlementof the supports.
tied arch
Three-Hinged Arches
The third hinge is located at the crown & thesupports are located at different elevations
To determine the reactions at the supports, the archis disassembled
Three-Hinged Arches
In order to determine the reactions at the supports, the arch is disassembled and thefree-body diagram of each member. Here there are six unknowns for which sixequations of equilibrium are available. One method of solving this problem is to applythe moment equilibrium equations about points A and B. Simultaneous solution will yieldthe reactions Cx and Cy. The support reactions are then determined from the forceequations of equilibrium.
Three-Hinged Arches
Once all support reactions obtained, the internal normal force, shear, and momentloadings at any point along the arch can be found using the method of sections. Here, ofcourse, the section should be taken perpendicular to the axis of the arch at the pointconsidered.
Example
The three-hinged open-spandrel arch bridge has aparabolic shape and supports a uniform load. Show thatthe parabolic arch is subjected only to axial compressionat an intermediate point such as point D. Assume theload is uniformly transmitted to the arch ribs.
Solution
Applying the equations of equilibrium, we have:
040 320 20 0
160
Entire Arch:With anti‐clockwise direction moments as ve,
( m) kN( m)
kN
A
y
y
MC
C
Solution
0160 10 160 20 10 0
160
0 160
0160 160 00
Arch segment BC:With anti‐clockwise direction moments as ve,
kN( m) kN( m) ( m)kN
kN
kN kN
B
x
x
x x
y
y
y
MC
C
F B
F
B
B
Solution
A section of the arch taken through point D
2 2
210
1010 10 20 2 5
20 0 520
26 6m
m
( ) / ( ) . m
The slope of the segment at D is:
tan .( )
.x
x
y
dyx
dx
Solution
0160 26 6 26 6 0
0
80 26 6 26 6 0
080 5 160 2 5 0
Applying the eqn of equlibrium, Fig 5.10(d), we have:
kN cos . sin .
kN sin . cos .
With anti‐clockwise moments as ve:
kN( m) kN( . m)
x
o oD D
y
o oD D
D
D
F
N V
F
N V
MM
178 9
0
0
.D
D
D
N kN
V
M
Example
The tied three-hinged arch is subjected to the loadingshown. Determine the components of reaction at A and Cand the tension in the cable.
Solution on whiteboard
Example
Determine the horizontal and vertical components ofreaction at A, B, and C of the three-hinged arch. AssumeA, B, and C are pin connected.
Solution on whiteboard
Example
The three-hinged spandrel arch is subjected to theuniform load of 20 kN/m. Determine the internalmoment in the arch at point D.
Solution on whiteboard