Brighten up your Miata with a touch of LEDs! The CorkSport LED Light Kit is an all inclusive easy to install LED kit for your interior and exterior accessories. The kit includes the front and rear running lights, trunk, rear license plate, and cabin light. Give your feedback for the CorkSport LED Light Kit by submitting a review at: http://corksport.com/2016-mazda-miata-led-light-kit.html

General Info. Part #: NDM-9-011-10 Time Est: 90 Minutes Wrench Rating: 1/5

Tooling List Flat Head Screw Driver #2 Phillips Head Screw Driver 90 Degree Pick Tool Needle Nose Pliers

Parts List 1. Two Festoon Quad LED Bulbs 2. Six T10 Triple LED Bulbs

Pre-Installation Notes:

Materials and Time:

P

Part # NDM-9-011-10

Need Help With Your Installation? Call (360) 260-CORK

OEM incandescent light bulbs will be hot immediately after use. Allow the OEM bulb 1-2 minutes to cool before removal.

These instructions were written for reference only and the use of a factory service manual is recommended. Please read these instructions thoroughly prior to starting installation

LED bulbs are directional. After installing each LED bulb, please power up the bulb to verify it is working. If not, de-power the bulb and flip it around.

These installation instructions were written using a 2016 ND MX-5 Launch Edition. Other models will be similar.

CorkSport LED Light Kit 2016+ Mazda MX-5

CorkkSporort L

s. The kit includes the front anding lights, trunk, rear license plate,

ght. Give your feedback for the CorkSby submitting a review at: http:// m/2016-mazda-miata-led-light-kit.h

rearand cabin

OEM incandndescent lightminutes to cool before

ese instructions were written fommended. Please read these i

These installation instructions wmodels will be similar.

bulbs wile removal

be hot

Drivercrew Driver

1. Two Festoon Quad LED Bulbs2. Six T10 Triple LED Bulbs122

ED bulb, please power up the bulbt around.

Installation Section 1: Cabin Light Pg. 2 Section 2: Trunk Light Pg. 3 Section 3: Rear License Plate Lights Pg. 4 Section 4: Rear Marker Light Pg. 5 Section 5: Front Marker Light Pg. 6

Order of Operations & Table of Contents

1 of 7

Part # NDM-9-011-10

InstallationSection 1: Cabin Light

Trunk Light Rear License Plate Lights Rear Marker Light

der of Operations & Table of Co

a) Move the switch to the “OFF” position.

b) Use the 90 degree pick to remove the lens cover. There is a small indent to pull on where the pick point is located. Pull downward to remove the lens cover. Shown in Figure 1a.

c) Remove the OEM bulb with the pick.

d) Install the Festoon LED bulb as shown in Figure 1b.

Part # NDM-9-011-10

Detailed Instructions

1. Cabin Light Replacement

Need Help With Your Installation? Call (360) 260-CORK 2 of 7

Figure 1b

Figure 1a

e) The (-) negative side of the LED bulb should be on the LH side of the vehicle.

f) Move the switch to the “ON” position to confirm bulb is working.

g) If not working then remove bulb and rotate 180 degrees.

h) Reinstall the lens cover.

switch to the “OFF”

b) Use the 90 degree pick to removethe lens cover There is a sm

led Instructions

1. Cabin Light Replacementtt

position to confirm bulbworking.

not working then remove bd rotate 180 degrees.

er.

is

a) Use a pick or flathead screwdriver to pop out the lens. Red arrow in Figure 1a.

b) Disconnect the entire lens from white electrical connector. Red circle in Figure 1b.

c) Remove the OEM bulb and the connector side metal bracket shown with the red arrow in Figure 2b.

d) Using small needle nose pliers bend the metal bracket as shown in Figures 2c and 2d.

e) Reinstall the metal bracket then install the Festoon LED bulb with the (-) terminal towards the connector side.

f) Reconnect the wire and confirm that the LED works. If not then rotate 180 degrees.

Part # NDM-9-011-10

Detailed Instructions

2. Trunk Light Replacement

Need Help With Your Installation? Call (360) 260-CORK 3 of 7

Figure 2b Figure 2a

Figure 2c: Before Bending Figure 2c: After Bending

a) Use a pick or flathe

ect the entire lens from white e

led Instructions

2. Trunk Light Replacementntt

d) Using small needle nose pliers bend the met

oon LED b

ks. If not then rotate 180 degrees.

r Bending

a) Follow Figure 3a – 3c to remove each side of the license plate light housing from the bumper. Use the pick to pull the loose as shown in Figure 3b.

b) Once the housing is loose from the bumper, rotate the housings counter-clockwise to unlock it from the bulb electrical connect. As shown in Figure 3d.

c) Remove the OEM bulb and install the T10 LED bulb. It is a tight fit.

d) Repeat above steps for other license plate light, then power up the lights to confirm operation. Rotate LED bulbs 180 degrees if not working.

e) Reinstall the housings onto the bulb connectors and them back into the bumper.

Part # NDM-9-011-10

Detailed Instructions

3. Rear License Plate Light Replacement

Need Help With Your Installation? Call (360) 260-CORK 4 of 7

Figure 3a

Figure 3b

Figure 3c

Figure 3d

a) Figure 3a – 3the license plate light housing

bumper. Use the pick toshown in Figure 3b.

b) Once the housing is loose from thebumper, rotate the housings counter-clockwise to unlock it

led Instructions

3. Rear License Plate Light Replacementt

igure 3a

bumper.

re 3c

a) Locate the rear marker light behind the rear wheel well inner fender.

b) Rotate the bulb connector counter-clockwise to remove. Shown in Figure 4a.

c) Remove the OEM bulb then install a T10 LED bulb. It is a tight fit.

d) Repeat the above steps for the other rear marker light.

Part # NDM-9-011-10

Detailed Instructions

4. Rear Marker Light Replacement

Need Help With Your Installation? Call (360) 260-CORK 5 of 7

Figure 4b

Figure 4a

e) Power-Up the lights to verify operation. If not working then remove bulb and rotate 180 degrees.

f) Align the largest tab on the bulb connector with the largest slot in the light housing. Shown in Figure 4b.

g) Press the bulb connector into the housings then rotate clockwise to lock.

he rear marker lighthe rear wheel well inner

b) Rotate the bulb connectorcounter-clockwise to remove.

led Instructions

4. Rear Marker Light Replacacement

st tab on thewith the larges

t housing. Show4b.

the bulb connector into thehen rotate clockwise to

) Align the largest connector wthe light F

bulbst slot in

wn in

a) Using a #2 Phillips screwdriver, remove the four screws circled in blue in Figure 5a.

b) Using a flathead screwdriver, remove the plastic push clips circled in red shown in Figures 5a & 5b.

c) Remove inner fender liner.

d) Locate the front marker bulb connector then rotate counter-clockwise to remove. Figure 5c.

e) Remove the OEM bulb then install a T10 LED bulb. It is a tight fit.

f) Power-Up the lights to verify operation. If not working then remove bulb and rotate 180 degrees.

g) Reinstall the bulb connector and the inner fender liner.

h) Repeat above steps for the other front marker light.

Part # NDM-9-011-10

Detailed Instructions

5. Front Marker Light Replacement

Need Help With Your Installation? Call (360) 260-CORK 6 of 7

Figure 5a

Figure 5b Figure 5c

a) #2 Phillips screwdriver,the four screws circled ingure 5a.

ver, remove the plastic push clips circled in red shown in Figures 5a & 5b.

led Instructions

5. Front Marker Light Replaacement

Reinstall the bulb connector ainner fender liner.

h) Repeat above steps farker light.

and the

7 of 7

Part # NDM-9-011-10

What’s Next:

Reduce intake flow restrictions and maintain cold intake air temperatures with the CorkSport Cold Air Intake. The CorkSport CAI utilized a high flow dry element filter, billet aluminum MAF and custom designed cold air box to give you a clean high flowing intake system. This awesome CorkSport product is still in development; look for it in the near future!

CorkSport Cold Air Intake System

Track tested and racer approved, the CorkSport Lowering Springs are a perfect match for your daily driven MX-5. The CorkSport Lowering Springs give the MX-5 an aggressive look without sacrificing functionality or ride quality.

CorkSport Lowering Springs

CORKSPORT Adjustable Swaybars Track tested and racer approved, the CorkSport Front and Rear Swaybars are a great compliment to the daily driver and track rat. Get your body roll under control with the CorkSport 3-Way Adjustable Swaybars.

hat’s Next:

C ustable SwaybarsTrack tested and racer approved, the CorkSport Fand Rear Swaybars are a great compliment to thdaily driver and track rat. Get your body roll control with the CorkSport 3-Way Adjust

Sport Cold Air Intake System

CorkSport Lowering Springs

aluma clTh