Technical DataANTIFOULING SEAQUANTUM FB

Product descriptionAntifouling SeaQuantum FB is a tin-free high performance self-polishing antifouling, based on hydrolysing organosilyl polymer as binder. This binder dissolves in seawater at a rate permitting the continuous exposure of fresh antifouling. IMO Anti-fouling System Convention compliant (AFS/CONF/26).

Recommended useAs an antifouling for newbuildings and major refurbishment, for flatbottom areas on vessels operating at medium speed with drydocking intervals up to 60 months.

Film thickness and spreading rateMinimum Maximum

Film thickness, dry (m) 75 150 Film thickness, wet (m) 160 320 Theoretical spreading rate (m/l) 6,2 3,1

Physical properties Colour Dark Red, Light Red Solids (vol %)* 47 2

Flash point 252 (Setaflash)

VOC 3,92 lbs/gal (470 gms/ltr) USA-EPA Method 24460 gms/ltr UK-PG6/23(97). Appendix 3

*Measured according to ISO 3233:1998 (E)

Surface preparationCoated surfacesTo be applied on a clean, dry approved primer/undercoat or intact self-polishing antifouling in accordance with Jotun's requirements. Remove surface contamination by high pressure fresh water cleaning.

Other surfacesThe coating may be used on other substrates. Please contact your local Jotun office for more information.

ANTIFOULING SEAQUANTUM FB Page 1 of 3

Condition during applicationThe temperature of the substrate should be minimum 3C above the dew point of the air, temperature and relative humidity measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure correct drying.

Application methods Spray Use airless spray Brush May be used but care must be taken to achieve the specified dry film thickness. Roller May be used. However when using roller application care must be taken to apply

sufficient material in order to achieve the specified dry film thickness.

Application data Mixing ratio (volume) Single pack.

Thinner/Cleaner Jotun Thinner No. 7 Guiding data airless spray Pressure at nozzle 15 MPa (150 kp/cm, 2100 psi.). Nozzle tip 0.53 - 0.78 mm (0.021 - 0.031"). Spray angle 65 - 80 Filter Check to ensure that filters are clean.

Drying timeDrying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with:* Good ventilation (Outdoor exposure or free circulation of air)* Typical film thickness* One coat on top of inert substrate

Substrate temperature 5C 10C 23C 40C Surface dry 60 min 45 min 30 min 15 min Through dry 8 h 6 h 4 h 3 h Dry for launching 1 12-24 h 10-22 h 8-20 h 8-16 h Dry to recoat, minimum 2 12 h 9 h 7 h 6 h

1. Indicate the time which normally occurs in a drydocking situation where the drying time depends on the total film thickness of primer/antifouling applied. The drying time will increase with increasing film thickness.

2. The surface should be dry and free from any contamination prior to application of the subsequent coat.

The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special conditions could be included.

Recommended type of primer:

Anticorrosive primer system suitable for purpose with Safeguard Universal ES or Vinyguard Silvergrey 88 as a sealer coat/tie-coat.

ANTIFOULING SEAQUANTUM FB Page 2 of 3

Other systems may be specified, depending on area of use

StorageThe product must be stored in accordance with national regulations. Storage conditions are to keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.

HandlingHandle with care. Stir well before use.

Packing size20 litre container.

Packing may vary from country to country according to local requirements.

Health and safetyPlease observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

For detailed information on the health and safety hazards and precautions for use of this product, we refer to the Material Safety Data Sheet.

DISCLAIMER The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical experience. However, as the product is often used under conditions beyond our control, we cannot guarantee anything but the quality of the product itself. We reserve the right to change the given data without notice.Footer - English

Head Office & Nordic

Jotun A/S

P.O. Box 2021

N-3248 Sandefjord

Norway

Phone +47 33 45 70 00Fax +47 33 46 46 13

Europe

Jotun Paints (Europe) Ltd.

Stather Road, FlixboroughNorth Lincolnshire DN15

8RR

United Kingdom

Phone +44 172 44 00 000Fax +44 172 44 00 100

Middle EastJotun U.A.E Ltd. LLC.

A l Quoz Industrial Area

P.O Box 3671Dubai U.A.E

Phone +971 4 3 39 50 00Fax +971 4 3 38 06 66

South East Asia

Jotun (Singapore) Pte. Ltd.No 11-15, Sixth Lok Yang

Road

Jurong

Singapore 628 111

Phone +65 6265 4711Fax +65 6265 7484

Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com

ISSUED 16 AUGUST 2005 BY JOTUNTHIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED

ANTIFOULING SEAQUANTUM FB Page 3 of 3