converter setting for tcp/ip communication between controller & pc (operating sw) ► catalog...
TRANSCRIPT
CONVERTER SETTING FOR TCP/IP COMMUNICATION
BETWEEN CONTROLLER & PC (OPERATING SW)
► Catalog ► Manual► Installation Guide
► Troubleshooting► Purchase Order
► IDTECK Home► e-Training Center
TCP/IP COMMUNICATION Through INTERNAL TCP/IP MODULE (IIM7100A) -1
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
• Direct Connection Mode
Change Jumpers
- TCP/IP module Insertion
- Change Jumper Setting for TCP/IP communication
RS422(Default) TCP/IP RJ-45 Connector
1
(Factory Setting)
• Make sure that the Jumpers (JP1 ~ JP4) must be set to the right position. • Connect LAN cable between RJ45 Jack of Controller.
- Connects to the network such as hubs or router : Use Direct LAN Cable- Connects to the PC directly : Use Cross LAN Cable
• Make sure that the arrow direction of module and Controller board must be the same. (applicable to version 3.0.0 or higher)
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
• Bypass Connection Mode
- Change Jumper Setting and Wiring for TCP/IP and slave RS422 Communication
• Connect LAN cable between RJ45 Jack of Controller #1- Connects to the network such as hubs or router : Use Direct LAN Cable- Connects to the PC directly : Use Cross LAN Cable
• Cross-connect RS422 wires between Controller #1 and Controller #2. (①)• Direct-connect RS422 wires between Controller #2 and Controller #3~#n.(②)
• Change Jumper Setting- Controller #1 : Make sure that the Jumpers(JP1~JP4) must be set to the right position.- Controller #2~#n : Make sure that the Jumpers(JP1~JP4) must be set to the left position.
TCP/IP COMMUNICATION Through INTERNAL TCP/IP MODULE (IIM7100A) - 2
INTERNAL TCP/IP MODULE SETUP (IIM7100A)
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
• Software Setting
Network Tab
• After running converter setting program and press Search Icon, it will search TCP/IP Module
connected to your network.
TCP/IP COMMUNICATION THROUGH EXTERNAL
TCP/IP MODULE (ILAN422 & 485)
TCP/IP COMMUNICATION Through EXTERNAL TCP/IP CONVERTER
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
LAN, WAN, INTERNET
LAN, WAN, INTERNET
RS422
RS232LAN, WAN, INTERNET
LAN, WAN, INTERNET
• RS232 to TCP/IP Conversion
TCP/IPConverter
TCP/IPConverter
• RS422 to TCP/IP Conversion
LAN, WAN, INTERNET
LAN, WAN, INTERNET
RS485
TCP/IPConverter
- 505R, iCON100, Finger007, Finger006, FGR006, etc… (built- in RS232 module)
- RFL200C, 505R, iCON100, Finger007, Finger006, FGR006, FGR007, etc… (built –in RS485, RS422 module)
- 505R, iCON100, Finger007, Finger006, FGR006, FGR007, etc… ( built –in RS422 module )
15m
15m
• RS485 to TCP/IP Conversion
EXTERNAL TCP/IP CONVERTER SETUP (ILAN422/ILAN485)
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
ControllerILAN422/ILAN485
(9Pin D-SUB Connector)
RXD Pin 3(TXD)TXD Pin 2(RXD)GND Pin 5(GND)
• RS232 to TCP/IP Conversion
ILAN422 ILAN485
EXTERNAL TCP/IP CONVERTER SETUP (ILAN485)
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
ControllerILAN485
(Terminal Block)RS485
ProductRXD+ (RS485 A) 485 +RXD– (RS485 B) 485 -
RS422 Product
RX+, TX+ 485 +RX- , TX- 485 -
• RS485 to TCP/IP Conversion
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
ControllerILAN422
(Terminal Block)RX+ T+RX- T-TX+ R+TX- R-
• RS422 to TCP/IP Conversion
CROSSCONNECTION
EXTERNAL TCP/IP CONVERTER SETUP (ILAN422) - 1
► Catalog ► Manual► Installation Guide► Troubleshooting► Purchase OrderCopyright (c) 2008 IDTECK.
All rights reserved.
• User Name ： admin• Password ： admin
• Software Setting
• After the program is opened, click the Refresh button. Then, the information of all the LAN converters connected to the same network will be displayed as in the picture below.
• Click the LAN converter that you’d like to configure, then the IP Address and SubMask fields will be automatically filled.
EXTERNAL TCP/IP CONVERTER SETUP (ILAN422) - 2
For more information,
Contact us at
Thank you.
Copyright (c) 2008 IDTECK.
All rights reserved.