LIMITED, PRO-RATED WARRANTYConfer Plastics, Inc. warrants their swimming pool ladders to be free from defects in workmanship for one year from date of purchase. After the first year the cost to replace a part is as follows:

MODELS #626B ALL OTHER MODELS:2nd Year - 40% 2nd Year - 20%3rd Year - 80% 3rd Year - 40%

4th Year - 60%5th Year - 80%

Plus shipping/handling charges

DO NOT RETURN DEFECTIVE PART TO DEALERThe defective part should be returned, postpaid, to: Confer Plastics, Inc.

97 Witmer RoadNorth TonawandaN.Y. 14120-2421

Enclose proof-of-purchase (receipts, etc.) showing date purchased, your name, address, and daytime phone number.You will be notified of cost to replace part.This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Printed in U.S.A.

MODEL #7000

“ELIMINATOR” A-FRAME LADDERAssembly Instructions

Purchase our #CK100Conversion Kit and cut the handrails under thedeck platform as indicated in the photobelow. Be sure to cut the legs on the “swing up” side of theladder. Follow theinstructions providedwith the conversionkit to fasten the ladder to the deck.

Flush to deck

OPTIONAL ACCESSORYSKIM-IT SKIMS OFF DEBRISCut cleaning time 75% withskimmer extension that guides debris directly into your skimmer. Fits most in-ground and above-ground pool skimmers. Corrosion-resistant plastic Skim-It installs in seconds without tools.

*DANGER: Never use an electric drill in or around the pool

MADE IN THE U.S.A. by: Made in U.S.A. by

To convert this ladder to a Deck ladder

Swing up instructionsWhen not in use always secure ladder by swingingup outer treads and locking with cable lock provided.

To swing up the outer treads stand on thebottom tread, grasp the underside of thesecond lowest tread and swing it out toward you. Swing them up until the tread connectors drop into the preformed locks on each leg and stay in the upright position.To lower the treads lift them straight up toclear the locks and carefully swing themdown toward you.

SAFETY RULES• Locate ladder on a solid base• One person on the ladder at a time• Ladder MUST be installed

per manufacturer’s instructions• DANGER: No Jumping or Diving from ladder• Face ladder when entering and

leaving pool• To prevent entrapment or drowning -

Do not swim through, behind or around ladder• Ladder to be used as a swimming pool ladder only• Ladder must be fastened to top seat• Maximum weight on steps not to exceed 300 lbs.• When ladder is not in use lock up outer treads with cable lock

providedWARNING: Exceeding the recommended weight requirement may cause theladder to fail.

To order call 1-800-635-3213

97 Witmer RoadNorth Tonawanda, New York 14120-2421Toll Free U.S. 800-635-3213716-694-3100 / FAX 716-694-3102www.conferladders.com

4

SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER

Locatecablelockhere

As required by ANSI/NSPI - This ladder is equipped with an anti-entrapment barrier to prevent children from swimming behindor through the rungs of the ladder. It is NOT intended as a substitute for proper adult supervision.

See cuttinginstructionson insert

CP-7000 09/04

Confer 7000_9_04 9/23/04 2:58 PM Page 1

PARTS LIST

4 - Handrail / Leg

1 - Deck Platform

2 - Bottom Tread

8 - Upper Tread (Slip-on Style)

2 - Adjustable Brace

1 - Tread Connector (Left Hand)

1 - Tread Connector (Right Hand)

MODEL # 7000“ELIMINATOR” A-FRAME LADDER

ADJUSTABLE to fit 48”TO 54” ABOVE GROUND POOLSHARDWARE PACK

26 - #10 x 1-1/4" Screw

2 - 1/4-20 x 3-1/4" Bolt

6 - 1/4" Washer

2 - 1/4" Nylon Nut

2 - 1/4-20 x 2-1/4" Bolt

2 - 1/4" Hex Nut

4 - Push in Plug

1 - Cable Lock Set

IMPORTANT: Remove the wedges from thedeck platform protrusions and SAVEfor step 5.

Slide the handrail/ legstogether as shown.Apply liquid soap orspray lubricant to aidassembly.

Tools required for assembly:Hammer or mallet, Cordless drill motor, 1/8" & 9/32" drill bits, Phillips screwdriver bit. Pliers, 7/16" wrench or adjustablewrench.

Twist and save. Pliers may beuseful to aid in removal.

Step 3.

Place one handrail/leg assembly on a clean flat surfaceand push the deck platform protrusions in the openings.

Step 4.

Repeat the process with the second handrail/leg assembly,pushing firmly down onto the deck protrusions to ensure asecure fit.

Step 8.

Step 5.

Insert the four wedges that were saved from step 1 into the top of the openings as shown.

Insert wedges

Step 7.

Slide the three remaining upper treads intoposition in the ladder legs. Position the rightand left hand tread connectors onto the endsof the treads and fasten them to the ladderlegs, through the pre-formed holes, using two1/4-20 x 3-1/4" bolts four washers and twonylon nuts (as shown in exploded diagram).Tighten securely but do not overtighten. Attachthe tread connectors to the ends of each treadusing #10 x 1-1/4" screws (four per tread).

Step 9. Step 10.

Attach Bottom treads

Stand here

Stand here

Push down firmly.Push down firmly.

32

Step 6.Slide five uppertreads into positionso they are restingon the double nubsof the legs (asshown in diagram).Secure the treadsto the legs using#10 x 1-1/4" screws(two per tread)through the pre-drilled hole.

Do notattach thethreeremaininguppertreads tothe legs.

Tread connectors

1/4” Nylon Nut

1/4”-20 x 3-1/4”Bolt

1/4" Washer

TILT

Locate the ladder at the desiredposition on the pool and place oneof the adjustable braces on the sideof the ladder so that it rests on thetop of the pool. Secure theadjustable brace to the ladder withtwo #10x 1-1/4" screws. Repeat forother brace. Note: the adjustablebraces are not needed if the deckplatform of the ladder rests on thetop of the pool.Using the braces as locators (or thedeck platform), drill two 9/32" holesthrough the pool top seat. Be care-ful not to damage liner or pool wall.Fasten the ladder to the pool topusing the two 1/4-20 x 2/1/4" bolts,washers and hex nuts.

26 2 6 2 2 2 4

Step 1. Step 2.

Stand on one of the uppertreads to snap the legs intothe bottom tread.

Nubs

Place the ladder in the pool and filllegs with waterthrough the openingswith a hose. Thenplug the holes usingthe four push inplugs. Tilt it so the airis released from allthe submergedtreads.

(Not To Scale)

Step 8a. Please refer to the separate instruction sheet for anti-entrapment barrier installation.

Confer 7000_9_04 9/23/04 2:58 PM Page 3