controls of super critical 3 rd feb 2009 controls of super critical boilers presentation by ajay...
TRANSCRIPT
Controls of Super Critical 3 rd Feb 2009
CONTROLS OF SUPER CRITICAL BOILERS
Presentation ByAJAY SHUKLA
Sr.Faculty PMI,
Controls of Super Critical 3 rd Feb 2009
Boiler Turbine Control
Controls of Super Critical 3 rd Feb 2009
Boiler Following Mode
Controls of Super Critical 3 rd Feb 2009
Turbine Following Mode
Controls of Super Critical 3 rd Feb 2009
Coordinate Mode Control
Controls of Super Critical 3 rd Feb 2009
Coordinate Mode Control
Controls of Super Critical 3 rd Feb 2009
Drum and OT Control Comparison
Controls of Super Critical 3 rd Feb 2009
Drum and OT Control Comparison
Controls of Super Critical 3 rd Feb 2009
OT Control Overview
Controls of Super Critical 3 rd Feb 2009
Cycle of Supercritical Power Plant
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
Supercritical Power Plant
Controls of Super Critical 3 rd Feb 2009
OT Control Overview
Controls of Super Critical 3 rd Feb 2009
OT Start up Control mode
Controls of Super Critical 3 rd Feb 2009
Super Critical Units Controls Mode
Controls of Super Critical 3 rd Feb 2009
Flushing Mode
Controls of Super Critical 3 rd Feb 2009
Flushing Mode
Controls of Super Critical 3 rd Feb 2009
Start-Up System with Recirculation
HPH
BFP
Deaerator
C
C
WW
ECO
To Condenser
C
HWL
SH
Start-Up System Recirculation Pump in Main Bypass Line
Sep
arat
or
Fla
sh
Tan
k
Controls of Super Critical 3 rd Feb 2009
Start UP System
Controls of Super Critical 3 rd Feb 2009
START-UPIf the water system of the boiler is empty (economizer, furnace walls, separators), then the system is filled with approximately 10% TMCR feed water flow. When the level in the separator reaches set-point, the WR valve will begin to open. When the WR valve reaches >30% open for approximately one minute, then increase feed water flow set-point to 30% TMCR. As the flow increases, WR valve will reach full open and ZR valve will begin to open. The water system is considered full when:
The separator water level remains stable for two(2) minutesand
The WR valve is fully opened and ZR valve is >15% open for two(2) minutes.
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
SEPARATOR STORAGE TANK LEVEL CONTROL
• Separator level is maintained by the combined action of a separator storage tank level feed water demand and the positioning of WR and ZR drain valves.
• Feed water demand is developed in response to separator storage tank level error and total fuel flow so as to prevent tank level from dropping too low.
• The WR and ZR valves are controlled in a split range manner to maintain the liquid level once the level reaches a high limit.
• The WR valve will respond first and then the ZR when the WR exceeds its linear operating range.
• Tank geometry is such that fluctuations in tank level are very dynamic, for this reason, only proportional control action established through the WR/ZR function curves is used to position these valves in response to level error.
Controls of Super Critical 3 rd Feb 2009
UG VALVE CONTROL
Control objective:Maintain minimum economizer inlet flow.Control action:
• The boiler circulating pump is started following the start of a turbine-driven feed water pump and the final clean-up cycle. This pump circulates feed water from the evaporator outlet back to the economizer inlet.
• Located at the outlet of this pump is the UG valve which controls economizer inlet flow during the start-up phase of operation. Demand for this recirculation control valve is established based on measured economizer inlet flow compared to a minimum boiler flow set point.
Controls of Super Critical 3 rd Feb 2009
Separator water circuit of Super Critical
Controls of Super Critical 3 rd Feb 2009
FEEDWATER CONTROL LOOP
Control objective:• Develop total unit feed water demand as required to support unit
load. • Adjust feed water demand to maintain desired separator outlet
temperature.• Adjust separator outlet temperature set point as required to maintain
acceptable platen superheat spray control range.• Incorporate separator storage tank level (wet mode) feed water
demand.• Maintain minimum required economizer inlet flow..
Controls of Super Critical 3 rd Feb 2009
Feedwater Control
Natural circulation boiler Once-through boiler
Feedwatercontrol
Level
Feedwater
Steam flowm•
EvaEco
T
T
Enthalpy
Feedwatercontrol
Feedwater
TP
Eco
Eva
Controls of Super Critical 3 rd Feb 2009
Feed water firing rate ratio control
Controls of Super Critical 3 rd Feb 2009
Feed water firing rate ratio control
Controls of Super Critical 3 rd Feb 2009
Process Setpoint
Feed Forwardf(x)
K
d dt
P +/-
C -/+
C +/-
P +/-
X
MODEL
Feed Forward with model
Controls of Super Critical 3 rd Feb 2009
process FF setpoint
K
d dt
P +/-
C -/+
X
C +/-
P +/-
f(x)
PROCESS FF
K
d dt
P +/-
C -/+
f(x)
C +/-
P +/-
Feed Forward
Controls of Super Critical 3 rd Feb 2009
t[sec]0 60 120
C
180 240 300
Water wall Temperature
MW
_
+Fuel with model
Turbine setpoint
Without model
Model predictive control
D:\moje\Dokumentacja\litwa\unit #6\model
Controls of Super Critical 3 rd Feb 2009
Firing Rate Master
Controls of Super Critical 3 rd Feb 2009
Fuel Rate Master
Controls of Super Critical 3 rd Feb 2009
Feed Forward Firing Rate Control
Controls of Super Critical 3 rd Feb 2009
Feed Forward Firing Rate Control
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
Yuhuan 4x1000MW Preparation of light off
Controls of Super Critical 3 rd Feb 2009
Multi-combusting Nozzles with Separated Overfire Air Damper
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
Controls of Super Critical 3 rd Feb 2009
START-UP contd.. Water flows through the economizer and evaporator, and discharges the boiler through the WR valve to the flash tank and via connecting pipe to the condenser. Start BCP and open the UG valve to establish minimum water wall flow at 30% TMCR. As the pressure is raised, first the WR and then the ZR valves will open when
•separator water level increases due to boiler water swell. As pressure further•increases, the WR and ZR valves will start to close as the water level decreases.
•The steam temperature at the separator inlet will reach a stable superheated•condition at app. 30% TMCR, causing the level in the separator to decrease and•eventually disappear. The boiler is now in once-through mode (dry mode). The
•BCP (Boiler Circulating Pump) will be stopped automatically.
•It is extremely important that minimum water wall flow be maintained at all times when firing the boiler to prevent tube damage due to overheating.
Controls of Super Critical 3 rd Feb 2009
FEEDWATER CONTROL LOOP contd..
Demand for feed water is established predominately by the Boiler Master demand.
This signal, processed though a “boiler transfer function” provides the feed forward component of the total feed water demand.
The “boiler transfer function” is a tunable dynamic element providing a means to dynamically match the feed water feed forward demand to actual evaporator heat transfer.
Optimization of the feed forward in this manner minimizes temperature fluctuations that may otherwise result from varying dynamic response between the firing and feed water control systems (as they relate to evaporator heat transfer) thereby lessening the dependence on feedback correction.
Controls of Super Critical 3 rd Feb 2009
FEEDWATER CONTROL LOOP contd..
The first controller acts on a load dependent average platen spray differential temperature.
Its output represents the required adjustment to evaporator heat transfer/steam generation to maintain both the steam conditions and flue gas temperatures entering the platen superheat section so as to ensure adequate platen spray control range.
A second controller acts on a load dependent separator outlet temperature set point corrected by the platen spray differential temperature controllers output.
This controller acts to adjust feed water in response to firing system disturbances and the relatively fast effect they have on separator outlet steam temperatures.
The overall combined feed water feedback control action is such that feed water demand is responsive to changes in the overall unit heat transfer profile.
Controls of Super Critical 3 rd Feb 2009
FEEDWATER CONTROL LOOP contd..
The combined feed forward/feedback demand signal is subject to a minimum economizer inlet flow set point (wet mode) activated if the boiler circulation pump is not in service and the unit is being fired.
This ensures the minimum economizer inlet cooling flow is maintained by the feed water supply system in the event the start-up system is not available.
The feed forward/feedback demand signal is subject to a second “wet mode” feed water demand developed to support separator storage tank level control.
The resulting demand provides the set point to a feed water master controller.
The fuel/feed water ratio protection logic provides overriding control of individual feeder speed demands in the event of an excessively high fuel to feed water ratio.
Controls of Super Critical 3 rd Feb 2009
THANK YOUTHANK YOU