configuringthecisco1-,2-,and4-portserial ...€¦ ·...

Cisco Systems, Inc.www.cisco.com

Configuring the Cisco 1-, 2-, and 4-port SerialNetwork Interface Modules for Cisco 4400 SeriesISRs

July 21, 2014OL-31531-01

This document provides information that you should know to perform the configuration tasks forconfiguring required and optional features of the Cisco 1-, 2-, and 4-port Serial Network InterfaceModules on the Cisco 4400 Series Integrated Services Routers (ISRs). This document contains thefollowing sections:

• Information About the Cisco 1-, 2-, and 4-port Serial Network Interface Modules

• Configuring the Cisco 1-, 2-, and 4-port Serial Network Interface Modules

• Verifying the Configuration

• Additional References

Information About the Cisco 1-, 2-, and 4-port Serial NetworkInterface Modules

The Cisco 1-port, 2-port, and 4-port Serial Network Interface Modules (NIMs) are multi-protocolsynchronous serial NIMs supported on the Cisco 4400 Series ISRs. The Cisco 1-, 2-, and 4-port SerialNIMs expand the capabilities of the router to provide connectivity for synchronous interfaces in a widerange of applications including up to 8Mbps date rate for high speed high-level data link control(HDLC). These capabilities can be utilized as Point-to-Point Cisco HDLC WAN interface or frame relayinterface. The Cisco 1-, 2-, and 4-port Serial NIM software is capable of anti-counterfeit protection andprovides periodic system status information. The Cisco 1-, 2-, and 4-port Serial NIMs have their ownserial communication controllers (SCCs) and they do not rely on the host platform for SCCs. For moreinformation on the Cisco 1-, 2-, and 4-port Serial NIM LED and hardware features, see the HardwareInstallation Guide.

Information About the Cisco 1-, 2-, and 4-port Serial Network Interface Modules

2Configuring the Cisco 1-, 2-, and 4-port Serial Network Interface Modules for Cisco 4400 Series ISRs

Table 1 Cisco 1-port, 2-port, and 4-port Serial HWICs

Platform and Software RequirementsThe Cisco 1-, 2-, and 4-port Serial NIMs are supported on the Cisco 4400 Series ISRs and runs on theCisco IOS XE Release 3.12S and later.

Supported FeaturesThe following are the software features supported on the Cisco 1-, 2-, and 4-port Serial NetworkInterface Modules:

• Cyclic Redundancy Checking

• Timing Signals

• Encapsulation Protocols

Cyclic Redundancy Checking

Cyclic redundancy checking (CRC) is an error-checking technique that uses a calculated numeric valueto detect errors in transmitted data. All the Serial HWIC interfaces use a 16-bit frame check sequence(FCS) CRC by default. The sender of a data frame calculates the FCS. The sender appends the FCS valueto the message before sending a frame.The receiver recalculates the FCS and compares its calculation tothe FCS from the sender. If there is a difference between the two calculations, the receiver assumes thata transmission error occurred and sends a resend request to the sender. See the Step 4 for configuringCRC.

Timing Signals

The Cisco 1-, 2-, and 4-port Serial NIM interfaces support both the data terminal equipment (DTE) anddata communication equipment (DCE) mode, depending on the mode of the compact serial cableattached to the port. To use a port as a DTE interface, you only need to connect a DTE compact serialcable to the port. When the system detects the DTE mode cable, it automatically uses the external timingsignal. To use a port in DCE mode, you must connect a DCE compact serial cable and set the clock speedwith the clock rate configuration command. See Step 4 for setting up a clock rate.

Serial HWICs SKUsConnectorType

Number ofConnectors

PortsperConnectors

SupportedInterfaces

Maximumdata rate perPort

1 port multi-protocolSynchronous SerialNIM

NIM-1T 12in1 1 1 V.35, RS232,X.21, RS449,RS530, RS530A

8Mbps



8Mbps



8Mbps

Configuring the Cisco 1-, 2-, and 4-port Serial Network Interface Modules


Encapsulation Protocols

Encapsulation protocols connect the layer- 2 (link layer) protocols with the layer-3 (network layer)protocols. When traffic crosses a WAN link, the connection needs a layer 2 protocol to encapsulatetraffic. The Cisco 1-, 2-, and 4-port Serial NIM interfaces support the High-Level Data Link Control(HDLC), Point-to-point (PPP), and Frame Relay encapsulation protocols. The HDLC protocol, is therouter proprietary protocol that decodes proprietary framing used by the routers on the PPP links. Thestandard PPP protocol supports the PPP links analyzed by the HDLC and can also be utilized for FrameRelay. The standard Frame Relay encapsulation protocol is a versatile and common encapsulationprotocol used with Frame Relay. See Step 4 to set the encapsulation method.

Configuring the Cisco 1-, 2-, and 4-port Serial Network InterfaceModules

This section contains the following sections:

• Configuring Required Features, page 3

• Configuring Optional Features, page 5

Configuring Required Features

Prerequisites

• You must properly install the Cisco 1-, 2-, and 4-port Serial Network Interface Modules on yourrouter following the instructions provided in the Hardware Installation Guide.

• You must confirm the Cisco 1-, 2-, and 4-port Serial Network Interface Modules are recognized byyour router.

Restrictions

• Only synchronous serial interfaces are supported.

• Network timing interface is not supported

• Only hdlc/ppp/frame-relay protocols are supported

• Half duplex operation is not supported. Only the full duplex operation is supported.



Detailed Steps

Command Purpose

Step 1 configure terminal

Example:Router# configure terminal

Enters global configuration mode.

Step 2 interface serial slot/subslot/port

Example:Router(config)# interface serial 0/3/0

Selects the interface to configure and entersinterface configuration mode.

• slot/subslot/port—Specifies the location of theinterface.

Step 3 ip address address mask

Example:Router(config-if)# ip address 10.0.0.1 255.255.255.0

Sets the IP address and subnet mask.

• address—IP address

• mask—Subnet mask

Step 4 clock rate bps

Example:Router(config-if)# clock rate 8000000

Configures the clock rate for the hardware to anacceptable bit rate per second (bps). Range is from1200-8000000 bits per second.

Note The clock rate configuration is onlyapplicable to the DCE interfaces.

Note The following clock rate options aresupported: 1200, 2400, 4800, 9600, 14400,19200, 28800, 32000, 38400, 48000, 56000,57600, 64000, 72000, 115200, 125000,148000, 192000, 250000, 256000, 384000,500000, 512000, 768000, 800000, 1000000,2000000, 4000000, 5300000, 8000000

Step 5 encapsulation {hdlc | ppp | frame-relay}

Example:Router(config-if)# encapsulation {hdlc | ppp |frame-relay}

Sets the encapsulation type on the interface.

• hdlc—High-Level Data Link Control (HDLC)protocol for serial interface. This is the default.

• ppp—Point-to-Point Protocol (PPP).

• frame-relay—Frame Relay.

Step 6 mtu bytes

Example:Router(config-if)# mtu 1500

Configures the MTU size for the interface. Defaultis 1500 bytes.

• bytes—The range is 64 to 8100.



Configuring Optional Features

This section provides you the information on configuring options features and the Cisco IOS XEcommands required to configure these features:

• Enhanced Object Tracking

• Setting up NIM Bring up Time

• NRZI Line-Coding Format

• Enabling DTR Pulse-Time

• Monitoring DSR As a Line Up/Down Indicator

• Ignoring Input Signals

• Inverting the Clock Signal

Enhanced Object Tracking

On your serial NIM, you can enable the Enhanced Object Tracking (EOT) feature to consider thecarrier-delay timer when tracking the status of an interface. The carrier-delay command in trackingconfiguration mode enables tracking to consider the carrier-delay timer configured on an interface. Youcan specify a period of time (in seconds) to delay communicating status change of a tracked interface.

Example:Router(config)# track 3 interface ethernet 0/1 line-protocolRouter(config-track)# carrier-delay ?<0-60> Carrier Transitions delay secondsmsec delay specified in millisecondsRouter(config-track)# delay up 30

Setting up NIM Bring up Time

You can set a specific amount of time for the router to wait before trying to bring up a NIM interfaceafter the NIM goes down using the serial restart-delay command in the interface configuration mode.

Example:Router(config-if)# serial restart-delay 500

NRZI Line-Coding Format

The serial NIM supports the non return to zero inverted (NRZI) line-coding format for signaltransitions.NRZI uses relational encoding to interpret signals rather than determining absolute values.You can enable NRZI format using the nrzi-encoding command in the interface configuration mode.

Example:Router(config-if)# nrzi-encoding

Enabling DTR Pulse-Time

You can enable the data terminal ready (DTR) pulse signal intervals on the serial interfaces using thepulse-time command in interface configuration mode. When the serial line protocol goes down (forexample, because of loss of synchronization), the interface hardware is reset and the DTR signal is heldinactive for at least the specified interval. Setting up the DTR pulse signal intervals is useful for handlingencryption or other similar devices that use the toggling of the DTR signal to resynchronize.

Verifying the Configuration


Example:Router(config-if)# pulse-time 3

Monitoring DSR As a Line Up/Down Indicator

When the serial interface is operating in DTE mode, by default, it monitors the Data Carrier Detect(DCD) signal as the line up/down indicator. The attached DCE device sends the DCD signal by default.When the DTE interface detects the DCD signal, it changes the state of the interface to up.

In some configurations, such as an the Synchronous Data Link Control (SDLC) multidrop environment,the DCE device sends the Data Set Ready (DSR) signal instead of the DCD signal, which prevents theinterface from coming up. To tell the interface to monitor the DSR signal instead of the DCD signal asthe line up/down indicator, configure the ignore dcd command in the interface configuration mode.

Example:Router(config-if)# ignore dcd

Ignoring Input Signals

You can configure the ignore [cts|dcd|dsr|dtr|rts] command to ignore the incoming signals that maybe flapping due to certain cabling issues. When the ignore [cts|dcd|dsr|dtr|rts] command is config-ured, a signal is automatically seen as asserted.

Example:Router(config-if)# ignore [cts|dcd|dsr|dtr|rts]

Note For the ignore command, the availability of cts, dcd, dsr, dtr and rts keyword options depend on whetherthe interface is a DTE or DCE interface.

Inverting the Clock Signal

Systems that use long cables or cables that are not transmitting the TxC (clock) signal might experiencehigh error rates when operating at higher transmission speeds. If a Serial NIM port is reporting a highnumber of error packets, a phase shift might be the problem; inverting the clock might correct this phaseshift.

When the EIA/TIA-232 interface is a DTE, the invert-txclock command inverts the TxC signal the DTEreceives from the remote DCE. When the EIA/TIA-232 interface is a DCE, the invert-txclock commandinverts the clock signal to the remote DTE port. You can use the no invert-txclock command to changethe clock signal back to its original phase.

Example:Router(config-if)# invert txclock

Verifying the ConfigurationFollow these tasks to verify your configuration:

• Verifying Interface Port Connection

• Verifying the Cisco 1-, 2-, and 4-port Serial NIM Connection Using the loopback Command

• Verifying Using show commands



Verifying Interface Port ConnectionUsing the ping command, you can verify that an interface port is functioning properly.

The ping command sends echo request packets out to a remote device at an IP address that you specify.After sending an echo request, the system waits a specified time for the remote device to reply. Eachecho reply is displayed as an exclamation point (!) on the console terminal; each request that is notreturned before the specified timeout is displayed as a period (.). A series of exclamation points (!!!!!)indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate abad connection.

Following is an example of a successful ping command to a remote server with the address 10.0.0.10:

Router# ping 10.0.0.10Type escape sequence to abort.Sending 5, 100-byte ICMP Echoes to 10.0.0.10, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 msRouter#

If the connection fails, verify that you have the correct IP address for the destination and that the deviceis active (powered on), and repeat the ping command.

Verifying the Cisco 1-, 2-, and 4-port Serial NIM Connection Using the loopbackCommand

You can run a loopback test using a loopback command in DCE mode to verify the connection betweenthe peer router and the Serial NIM. When the loopback command is configured on a Cisco 1-port, 2-port,and 4-port Serial HWIC DCE serial port, any incoming data is looped back out on the transmit line. Also,any traffic sent from the Cisco 1-, 2-, and 4-port Serial NIM’s host router is looped back to itself withoutbeing processed by the NIM’s serial controller.

Note On a Cisco 1-, 2-, and 4-port Serial Network Interface Modules, the looback feature works as intendedonly when a serial interface is connected to a DCE cable.

Following example shows loopback command configured under interface configuration mode:

Router(config-if)# loopback

Verifying Using show commandsYou can use the output from the following show commands to verify your configuration:

• show version, page 8

• show platform, page 9

• show interfaces, page 9

• show start (start up config), page 10

• show run (running configuration), page 15



show versionRouter# show versionCisco IOS XE Software, Version BLD_V154_2_S_XE312_THROTTLE_LATEST_20140205_020103Cisco IOS Software, ISR4400 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), ExperimentalVersion 15.4(20140205:045828)[v154_2_s_xe312_throttle-BLD-BLD_V154_2_S_XE312_THROTTLE_LATEST_20140205_020103-ios 202]Copyright (c) 1986-2014 by Cisco Systems, Inc.Compiled Wed 05-Feb-14 00:17 by ciscouser

Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.All rights reserved. Certain components of Cisco IOS-XE software arelicensed under the GNU General Public License (“GPL”) Version 2.0. Thesoftware code licensed under GPL Version 2.0 is free software that comeswith ABSOLUTELY NO WARRANTY. You can redistribute and/or modify suchGPL code under the terms of GPL Version 2.0. For more details, see thedocumentation or “License Notice” file accompanying the IOS-XE software,or the applicable URL provided on the flyer accompanying the IOS-XEsoftware.

ROM: IOS-XE ROMMON

Router uptime is 1 hour, 27 minutesUptime for this control processor is 1 hour, 28 minutesSystem returned to ROM by reload at 13:58:53 CST Mon Feb 10 2014System restarted at 14:01:31 CST Mon Feb 10 2014System image file is "bootflash:isr4400-universalk9.BLD_V154_2_S_XE312_THROTTLE_LATES"Last reload reason: Reload Command

This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email [email protected].

Technology Package License Information:-----------------------------------------------------------------Technology Technology-package Technology-package

Current Type Next reboot------------------------------------------------------------------appx appxk9 RightToUse appxk9uc uck9 RightToUse uck9security securityk9 RightToUse securityk9ipbase ipbasek9 Permanent ipbasek9

cisco ISR4451-X/K9 (2RU) processor with 1376390K/6147K bytes of memory.Processor board ID FGL170910134 Gigabit Ethernet interfaces4 Serial interfaces32768K bytes of non-volatile configuration memory.4194304K bytes of physical memory.7393215K bytes of flash memory at bootflash:.

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html



Configuration register is 0x2102

show platform

Router# show platform

Chassis type: ISR4451-X/K9

Slot Type State Insert time (ago)--------- ------------------- --------------------- -----------------0 ISR4451-X/K9 ok 01:27:420/0 ISR4451-X-4x1GE ok 01:26:460/1 NIM-1T admin down 01:26:520/2 NIM-1T admin down 01:26:520/3 NIM-4T ok 00:27:49

1 ISR4451-X/K9 ok 01:27:422 ISR4451-X/K9 ok 01:27:42R0 ISR4451-X/K9 ok, active 01:27:42F0 ISR4451-X/K9 ok, active 01:27:42P0 Unknown ps, fail neverP1 PWR-4450-AC ok 01:27:26P2 ACS-4450-FANASSY ok 01:27:26

Slot CPLD Version Firmware Version--------- ------------------- ---------------------------------------0 13061029 12.2(20130629:014040) [ciscouser-ISR4...1 13061029 12.2(20130629:014040) [ciscouser-ISR4...2 13061029 12.2(20130629:014040) [ciscouser-ISR4...R0 13061029 12.2(20130629:014040) [ciscouser-ISR4...F0 13061029 12.2(20130629:014040) [ciscouser-ISR4...

show interfacesRouter# show interfaces serial 0/3/0Serial0/3/0 is up, line protocol is up

Hardware is NIM-4TInternet address is 11.1.4.1/24MTU 1500 bytes, BW 8000 Kbit/sec, DLY 20000 usec,

reliability 255/255, txload 250/255, rxload 250/255Encapsulation HDLC, loopback not setKeepalive not setLast input never, output 1d19h, output hang neverLast clearing of "show interface" counters neverInput queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 3184797855Queueing strategy: fifoOutput queue: 0/40 (size/max)5 minute input rate 7870000 bits/sec, 18920 packets/sec5 minute output rate 7853000 bits/sec, 18876 packets/sec

2987797065 packets input, 155365447380 bytes, 0 no bufferReceived 0 broadcasts (0 IP multicasts)0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort2983666535 packets output, 155150668066 bytes, 0 underruns0 output errors, 0 collisions, 18 interface resets0 unknown protocol drops0 output buffer failures, 0 output buffers swapped out1 carrier transitionsRTS up, CTS up, DTR up, DCD up, DSR up



show start (start up config)Router# show startup-configUsing 5456 out of 33554432 bytes!! Last configuration change at 15:07:45 CST Mon Feb 10 2014! NVRAM config last updated at 15:07:46 CST Mon Feb 10 2014!version 15.4service timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneno platform punt-keepalive disable-kernel-coreplatform shellplatform hardware throughput level 1000000!hostname Router-1!boot-start-markerboot systembootflash:isr4400-universalk9.BLD_V154_2_S_XE312_THROTTLE_LATEST_20140205_020103.SSA.binboot-end-marker!aqm-register-fnf!vrf definition Mgmt-intf!address-family ipv4exit-address-family!address-family ipv6exit-address-family!logging buffered 10000000!no aaa new-modelclock timezone CST 8 0!!!!!!!!!

no ip domain lookup

!ip dhcp pool LOCAL!!!!!!!!!!subscriber templating!frame-relay fast-restart



multilink bundle-name authenticated!!!!!!!!!!!!!license udi pid ISR4451-X/K9 sn FOC17042FJVlicense accept end user agreementlicense boot level appxk9license boot level uck9license boot level securityk9hw-module subslot 0/1 shutdown unpoweredhw-module subslot 0/2 shutdown unpoweredspanning-tree extend system-id!!redundancymode none!!!!!!ip ftp source-interface GigabitEthernet0ip ftp username rootip ftp password cisco!class-map match-any serialmatch protocol ftpmatch protocol ftp-datamatch protocol ftp-agentmatch anyclass-map match-all serial_mlp_lowmatch dscp af21class-map match-all testmatch anyclass-map match-any serial1match anyclass-map match-all mlp_lficlass-map match-all serial_mlp_highmatch dscp af41!policy-map serialclass serial

priority level 2policy-map serial1class serial

priority level 1policy-map serial_mlpclass serial_mlp_high

priorityclass serial_mlp_lowpolicy-map testclass test!



pseudowire-class fr_frencapsulation l2tpv3ip local interface Loopback0!!!!!!!crypto isakmp performance!!crypto ipsec transform-set serial ah-sha512-hmac esp-3des esp-sha-hmacmode tunnel

!!!!!!!!!interface Loopback0ip address 192.168.1.1 255.255.255.0!interface Port-channel1no ip addressno negotiation autoservice instance 1 ethernet

encapsulation untaggedbridge-domain 40

!!interface Port-channel2no ip addressnegotiation autoservice instance 1 ethernet


!!interface Multilink1ip address 100.0.0.1 255.255.255.0ip ospf 1 area 0no keepaliveppp multilinkppp multilink interleaveppp multilink group 1ppp multilink fragment delay 10ppp timeout multilink lost-fragment 0 10service-policy output serial_mlp!interface Multilink2ip address 101.1.1.1 255.255.255.0ppp multilinkppp multilink group 2!interface GigabitEthernet0/0/0no ip addressnegotiation auto!interface GigabitEthernet0/0/0.10



encapsulation dot1Q 10ip address 1.1.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/0.20encapsulation dot1Q 20ip address 1.2.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/0.30encapsulation dot1Q 30ip address 1.3.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/0.40encapsulation dot1Q 40ip address 1.4.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/1no ip addressnegotiation autoservice instance 2 ethernet

encapsulation dot1q 20bridge-domain 30

!!interface GigabitEthernet0/0/2no ip addressshutdownnegotiation auto!interface GigabitEthernet0/0/3no ip addressshutdownnegotiation autochannel-group 2!interface Serial0/3/0ip address 10.1.1.1 255.255.255.0no keepalive!interface Serial0/3/1ip address 11.1.1.1 255.255.255.0no keepalive!interface Serial0/3/2ip address 12.1.1.1 255.255.255.0no keepalive!interface Serial0/3/3ip address 13.1.1.1 255.255.255.0no keepalive!interface GigabitEthernet0vrf forwarding Mgmt-intfip address 10.74.30.216 255.255.255.0negotiation auto!router ospf 1network 1.1.1.0 0.0.0.255 area 0network 8.8.8.0 0.0.0.255 area 0!ip forward-protocol nd



no ip http serverno ip http secure-serverip route 2.1.1.0 255.255.255.0 Serial0/3/0ip route vrf Mgmt-intf 0.0.0.0 0.0.0.0 10.74.30.1!!arp 200.1.1.2 00c0.0100.0002 ARPAarp 102.0.0.12 00c0.0200.0001 ARPA!snmp-server community public RO!!control-plane!!!!!!mgcp behavior rsip-range tgcp-onlymgcp behavior comedia-role nonemgcp behavior comedia-check-media-src disablemgcp behavior comedia-sdp-force disable!mgcp profile default!!!!!alias exec shell request platform software system shellalias exec shfirm1 show platform software subslot 0/1 module firmwarealias exec shfirm2 show platform software subslot 0/2 module firmwarealias exec shfirm3 show platform software subslot 0/3 module firmwarealias exec shdrop show platform hardware qfp active statistics dropalias exec bqs show plat hard qfp ac infras bqs sche output default interf Serialalias exec ship show ip int brialias exec shfp show plat soft object-m f0 statistic!line con 0exec-timeout 0 0privilege level 15length 0stopbits 1line aux 0stopbits 1line vty 0 4exec-timeout 20 0privilege level 15no loginlength 0line vty 5 6exec-timeout 0 0privilege level 15no loginlength 0!monitor event-trace voip ccsip max-dump-limit 1000000ntp source GigabitEthernet0ntp peer 10.75.221.108ntp server vrf Mgmt-intf 10.75.221.108!end



show run (running configuration)Router# show runBuilding configuration...

Current configuration : 5585 bytes!! Last configuration change at 15:28:40 CST Mon Feb 10 2014! NVRAM config last updated at 15:07:46 CST Mon Feb 10 2014!version 15.4service timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneno platform punt-keepalive disable-kernel-coreplatform shellplatform hardware throughput level 1000000!hostname Router-1!boot-start-markerboot systembootflash:isr4400-universalk9.BLD_V154_2_S_XE312_THROTTLE_LATEST_20140205_020103.SSA.binboot-end-marker!aqm-register-fnf!vrf definition Mgmt-intf!address-family ipv4exit-address-family!address-family ipv6exit-address-family!logging buffered 10000000!no aaa new-modelclock timezone CST 8 0!!!!!!!!!

no ip domain lookup

!ip dhcp pool LOCAL!!!!!!!!!!subscriber templating



!frame-relay fast-restartmultilink bundle-name authenticated!!!!!!!!!!!!!license udi pid ISR4451-X/K9 sn FOC17042FJVlicense accept end user agreementlicense boot level appxk9license boot level uck9license boot level securityk9hw-module subslot 0/1 shutdown unpoweredhw-module subslot 0/2 shutdown unpoweredspanning-tree extend system-id!!redundancymode none!!!!!!ip ftp source-interface GigabitEthernet0ip ftp username rootip ftp password cisco!class-map match-any serial_nimmatch protocol ftpmatch protocol ftp-datamatch protocol ftp-agentmatch anyclass-map match-all serial_nim_mlp_lowmatch dscp af21class-map match-all testmatch anyclass-map match-any serial_nim1match anyclass-map match-all mlp_lficlass-map match-all serial_mlp_highmatch dscp af41!policy-map serialclass serial_nim

priority level 2policy-map serial_nim1class serial_nim

priority level 1policy-map serial_mlpclass serial_nim_mlp_high

priorityclass serial_mlp_lowpolicy-map test



class test!pseudowire-class fr_frencapsulation l2tpv3ip local interface Loopback0!!!!!!!crypto isakmp performance!!crypto ipsec transform-set serial ah-sha512-hmac esp-3des esp-sha-hmacmode tunnel

!!!!!!!!!interface Loopback0ip address 192.168.1.1 255.255.255.0!interface Port-channel1no ip addressno negotiation autoservice instance 1 ethernet


!!interface Port-channel2no ip addressnegotiation autoservice instance 1 ethernet


!!interface Multilink1ip address 100.0.0.1 255.255.255.0ip ospf 1 area 0no keepaliveppp multilinkppp multilink interleaveppp multilink group 1ppp multilink fragment delay 10ppp timeout multilink lost-fragment 0 10service-policy output serial_mlp!interface Multilink2ip address 101.1.1.1 255.255.255.0ppp multilinkppp multilink group 2!interface GigabitEthernet0/0/0no ip addressnegotiation auto



!interface GigabitEthernet0/0/0.10encapsulation dot1Q 10ip address 1.1.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/0.20encapsulation dot1Q 20ip address 1.2.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/0.30encapsulation dot1Q 30ip address 1.3.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/0.40encapsulation dot1Q 40ip address 1.4.1.1 255.255.255.0no cdp enable!interface GigabitEthernet0/0/1no ip addressnegotiation autoservice instance 2 ethernet

encapsulation dot1q 20bridge-domain 30

!!interface GigabitEthernet0/0/2no ip addressshutdownnegotiation auto!interface GigabitEthernet0/0/3no ip addressshutdownnegotiation autochannel-group 2!interface Serial0/3/0ip address 10.1.1.1 255.255.255.0no keepalive!interface Serial0/3/1ip address 11.1.1.1 255.255.255.0no keepalive!interface Serial0/3/2ip address 12.1.1.1 255.255.255.0no keepalive!interface Serial0/3/3ip address 13.1.1.1 255.255.255.0no keepalive!interface GigabitEthernet0vrf forwarding Mgmt-intfip address 10.74.30.216 255.255.255.0negotiation auto!router ospf 1network 1.1.1.0 0.0.0.255 area 0network 8.8.8.0 0.0.0.255 area 0



!ip forward-protocol ndno ip http serverno ip http secure-serverip route 2.1.1.0 255.255.255.0 Serial0/3/0ip route 2.2.1.0 255.255.255.0 Serial0/3/1ip route 2.3.1.0 255.255.255.0 Serial0/3/2ip route 2.4.1.0 255.255.255.0 Serial0/3/3ip route vrf Mgmt-intf 0.0.0.0 0.0.0.0 10.74.30.1!!arp 200.1.1.2 00c0.0100.0002 ARPAarp 102.0.0.12 00c0.0200.0001 ARPA!snmp-server community public RO!!control-plane!!!!!!mgcp behavior rsip-range tgcp-onlymgcp behavior comedia-role nonemgcp behavior comedia-check-media-src disablemgcp behavior comedia-sdp-force disable!mgcp profile default!!!!!alias exec shell request platform software system shellalias exec shfirm1 show platform software subslot 0/1 module firmwarealias exec shfirm2 show platform software subslot 0/2 module firmwarealias exec shfirm3 show platform software subslot 0/3 module firmwarealias exec shdrop show platform hardware qfp active statistics dropalias exec bqs show plat hard qfp ac infras bqs sche output default interf Serialalias exec ship show ip int brialias exec shfp show plat soft object-m f0 statistic!line con 0exec-timeout 0 0privilege level 15length 0stopbits 1line aux 0stopbits 1line vty 0 4exec-timeout 20 0privilege level 15no loginlength 0line vty 5 6exec-timeout 0 0privilege level 15no loginlength 0!monitor event-trace voip ccsip max-dump-limit 1000000ntp source GigabitEthernet0

Additional References


ntp peer 10.75.221.108ntp server vrf Mgmt-intf 10.75.221.108!end


Related Documents

MIBs

Technical Assistance

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list ofCisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. Theuse of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Related Topic Document Title

Information about Installing the Cisco 1-, 2-, and4-port Serial Network Interface Modules.

Installing the Cisco 1-, 2-, and 4-port Serial Network InterfaceModules for Cisco 4400 Series ISRs

Information on installing the Cisco 4400 SeriesIntegrated Services Router

Hardware Installation Guide for the Cisco 4400 Series IntegratedServices Router

Information on configuring Cisco 4400 SeriesIntegrated Services Routers

Software Configuration Guide for the Cisco 4400 Series IntegratedServices Router

Information on Interface Commands. Cisco IOS Interface and Hardware Component Command Reference

Regulatory compliance and safety information Cisco Network Modules and Interface Cards RegulatoryCompliance and Safety Information

MIB MIBs Link

• OLD-CISCO-CHASSIS-MIB

• CISCO-ENTITY-VENDORTYPE-OID-MIB

• CISCO-PRODUCTS-MIB

To locate and download MIBs for selected platforms, Cisco softwarereleases, and feature sets, use Cisco MIB Locator found at thefollowing URL:

http://www.cisco.com/go/mibs

Description Link

Technical Assistance Center (TAC) home page,containing 30,000 pages of searchable technicalcontent, including links to products, technologies,solutions, technical tips, and tools. RegisteredCisco.com users can log in from this page to accesseven more content.

http://www.cisco.com/public/support/tac/home.shtml

http://www.cisco.com/public/support/tac/home.shtml

http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/interface/command/ir-cr-book.html

http://www.cisco.com/en/US/docs/routers/access/4400/hardware/installation/guide/c4400isr.html

http://www.cisco.com/en/US/docs/routers/access/4400/software/configuration/guide/isr4400swcfg.html

http://www.cisco.com/en/US/docs/routers/access/interfaces/rcsi/IOHrcsi.html

http://www.cisco.com/en/US/docs/routers/access/interfaces/rcsi/IOHrcsi.html

http://www.cisco.com/go/mibs

http://www.cisco.com/en/US/support/index.html

http://www.cisco.com/go/trademarks



Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Anyexamples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only.Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2014 Cisco Systems, Inc. All rights reserved.