cnc router cat2008 - r.f. flood industrial supply inc. techniks products are backed by our 100%...
TRANSCRIPT
CNC Router Tooling and Accessories
Because your router’s performancedepends on high-precision tooling.
• Collet Chucks
• Drill Chucks
• Arbors
• Shrink Fit
• Collets
• Pull Studs
• Set-up Tools
• Aggregates
2008
see page 38…
Every holder is individually tested for quality & accuracy and comes with a lab certifi cation documenting accuracy and balance specifi cations.
Taper-to-Pocket T.I.R. 0.0001"Measured from taper O.D. to collet pocket I.D.
Taper Accuracy AT3 Taper ground to AT3 accuracy for maximum contact with spindle.
Power Coat NutsOur Power Coat nut holds 40% tighter than bearing nuts for best T.I.R. and rigidity.
Balanced NutBalanced nut reduces vibration to extend cutting tool life.
Techniks Certified Tooling Improves Router Performance
Balanced to 24,000 RPMFactory balanced to 24,000 RPM at G2.5 Custom balancing to 60,000 RPM available.
Lab Certified Accuracy Each tool holder is lab certified for accuracy and balance.
Ultra Precision ColletEach collet hand inspected. T.I.R. only 0.0002"
Techniks Certified = High Performance Tooling = Best T.I.R.
Use Techniks Certified Tooling for improved cutting and extended tool life.
Each Tool Individually Lab Certified How T.I.R. Affects Cutting Tool LIfe
T.I.R. (total indicator runout) is the measure of concentricity of the cutting tool in the tool holder. T.I.R. is measured in "tenths" or one-ten-thousandths of an inch.
Every .0001" T.I.R. loses 10% tool life
Cutting tool life decreases by 10% for every .0001" T.I.R. The rigidity and accuracy of Techniks tool holders minimizes T.I.R.
A full report comes with each tool.
Tool holders make the important con-nection between the machine spindle and the cutting tool.
Quality tool holders extend tool life by 150% or more.
0
50
100
150
200
Per
cen
t To
ol L
ife
T.I.R. in tenths0 2 4 6 8 10
COLLET CHUCKS
HSK F and HSK E ................4
ISO 20 and ISO 30 ................5
SK 30 .....................................5
BT 30 ......................................6
BT 35 ......................................7
ER Straight Shank Ext .........7
CMS Tool Holder ...................9
Table of Contents
Tool Holders
COLLETS
ER Inch Collets ................... 14
ER Metric Collets ................ 15
TG Collets ............................20
TG Nuts ................................21
Shoda Collets ......................22
Perske DIN 6388 Collets ....23
DNA Collets .........................24
Retention Knobs .................25
Collets & Nuts
ARBOR TOOL HOLDERS
HSK 63F ................................8
ISO 30 ..................................8
DRILL CHUCKS &
ADAPTERS
HP3 High Precision ...........9
Drill Adapters ....................9
SHRINK FIT HOLDERS
HSK 63F ........................ 10
ISO 30 ............................. 10
Shrink Fit Machines ......11
HYDRAULIC HOLDERS
HSK Hydraulics ................ 12
ISO Hydraulics ................. 12
Reducing Sleeves ........... 13
COLLET NUTS
Power Coat ER Nuts ........... 16
ER Bearing Nuts .................18
ER High Speed Mini ............18
Dust Cover Nuts (ER) ........19
Dust Cover Nut (TG) ...........21
Shoda Nuts ..........................22
Perske DIN 6388 Nuts ........23Special Orders .....................42
Part Number Index ..............44
Other Info
WRENCHES & GAUGES
Hand Wrenches ..................28
Torque Wrenches ...............29
Torque Wrench Adapters ..29
Tightening Fixtures ............30
Digital Height Gauge ..........31
Analog Axial Gauge ............31
Setup Equipment
AGGREGATE
HEADS
About our aggregates .......33
Single output (Mono) .........34
Double output (Duo) ..........35
Quad output (Quattro) .......36
Variable angle (Vario) ........37
Floating head (Soft-Touch 38
Light weight (Smart Line) 39
Output options ...................40
Aggregate Heads
DUST SEALS, WIPERS
Dust Seals (internal) ...........26
Dust Covers (external) .......27
Spindle Wipers ....................27
Tool Holders
Call us toll free: (800) 597-3921, Local: (317) 803-8000, Fax: (317) 803-8001, Email: [email protected]
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.4
HSK 63F and HSK E Collet Chucks for CNC Routers
HSK 63F Tool Holders
Part No. Description D A F N Collet Nut Wrench Flats
171.05.008.001 HSK 63F x ER 16 - 60* 63 60 26 32 46116 04613 26
171.05.008.002 HSK 63F x ER 16 - 100* 63 100 26 32 46116 04613 26
30000 HSK 63F x ER 32 - 70 63 70 26 50 46132 04616 36
30001 HSK 63F x ER 40 - 76 63 76 26 63 46140 04617 46
30002 HSK 63F x ER 40 - 90 63 90 26 63 46140 04617 46
30005 HSK 63F x ER 40 - 125 63 125 26 63 46140 04617 46
31025F HSK 63F x SYOZ 25 - 80 63 80 26 60 03638 03691 38
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24
• Balanced to 24,000 RPM at G2.5
• Inspection report included for accuracy and balance
• includes collet nut
HSK 32E, 40E, 50E, 63E Tool Holders for HSK E type spindle
Part No. Description D d1 l1 l2 Collet Nut Wrench Flats
31374-60 HSK 32E x ER 25 32 32 48 27 46125 04615 22
84.05.008.001 HSK 40E x ER 16 - 65* 40 28 65 45 46116 04613 24
84.05.008.002 HSK 40E x ER 25 - 75 40 42 75 55 46125 04615 27
84.05.008.003 HSK 40E x ER 32 - 100 40 50 100 80 46132 04616 35
85.05.008.002 HSK 50E x ER 32 - 85 50 50 85 59 46132 04616 36
86.05.008.002 HSK 63E x ER 32 - 90 63 50 90 64 46132 04616 none
86.05.008.003 HSK 63E x ER 40 - 120 63 63 120 94 46140 04617 none
50001 HSK 63E x ER 40 - 75 63 63 75 49 46140 04617 none
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24
����
��
• Balanced to 25,000 RPM at G2.5
• Inspection report included for accuracy and balance
• includes collet nut
Note: Measure the "l1" dimension with the collet in the nut. Dimensions are in millimeters.
Note: Measure the "A" dimension with the collet in the nut. Dimensions are in millimeters.
A
D N
F
flats
flats
All Techniks products are backed by our 100% satisfaction guarantee! 5
ISO and SK Tool Holders for CNC Routers
• Balanced to 25,000 RPM at G2.5
• Inspection report included for accuracy and balance
• includes collet nut
Note: Measure the "A" dimension with the collet in the nut. Dimensions are in millimeters.
SK Tool Holders for ANDI and Weeke CNC Routers
Part No. Description D A F N Collet Nut Wrench Flats
NT-54300130 SK-30 x SYOZ 25 - 70 50 70 15.9 60 included 03691 38
• Balanced to 25,000 RPM at G2.5
• Inspection report included for accuracy and balance
• includes collet nut
Note: Measure the "A" dimension with the collet in the nut. Dimensions are in millimeters.
ISO 30
ISO 20
ISO 20, 30, and 40 Tool Holders
Part No. Description D A F N Collet Nut Wrench Flats
06000-2016M ISO 20 x ER 16M - 52 w/HS mini nut & stud* *30 52 15.9 22 33116 04622 17
06000-2016MC ISO 20 x ER 16 - 52 coated HS mini nut & stud* 30 52 15.9 22 53116 04622 17
06000-2516 ISO 20 x ER 16 - 52* 30 52 15.9 32 46116 04613 17
06000-2520 ISO 20 x ER 20 - 52 30 52 15.9 35 46120 04614 17
12407-W ISO 30 x ER 11M - 100 50 100 15.9 16 23111 04621 14
12000-CMS ISO 30 x ER 32 - CMS 46 58 15.9 50 46132 04616 36
12213-W-50 ISO 30 x ER 32 - 50 50 50 15.9 50 46132 04616 47
12213-W-63 ISO 30 x ER 32 - 63 50 63 15.9 50 46132 04616 36
12213-W-90 ISO 30 x ER 32 - 90 50 90 15.9 50 46132 04616 36
12215-W-57 ISO 30 x ER 40 - 57 50 57 15.9 63 46140 04617 47
12040-CMS ISO 30 x ER 40 - CMS w/o nut 46 66 15.9 63 46140 04617 42
12261-W ISO 40 x ER 40 - 70mm 63.5 70 15.9 63 46140 04617 46
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24.
flats
flats
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.6
BT 30 Tool Holders for CNC Routers
BT 30, ER 20 Tool Holders
Part No. Description D A F N Collet Nut Wrench
06106 BT 30 x ER 20 - 70 46 70 20 34 41120 04610
06106-SLOTNUT BT 30 x ER 20 - 70 with slotted nut 46 70 20 35 46120 04614
06107 BT 30 x ER 20 - 135 46 135 20 35 41120 04614
06107-SLOTNUT BT 30 x ER 20 - 135 with slotted nut 46 135 20 35 46120 04614
06108-2.5 BT 30 x ER 20 - 2.5" 46 63.5 20 34 41120 04610
06108-2.5-SLOTNUT BT 30 x ER 20 - 2.5" with slotted nut 46 63.5 20 35 46120 04614
BT 30 ER 25 Tool Holders
Part No. Description D A F N Collet Nut Wrench
06109 BT 30 x ER 25 - 70 46 70 20 42 41925 04615
06110 BT 30 x ER 25 - 60 46 60 20 42 41925 04615
06111 BT 30 x ER 25 - 135 46 135 20 42 41925 04615
06111-90 BT 30 x ER 25 - 90 46 90 20 42 41925 04615
BT 30, ER 16 Tool Holders*
Part No. Description D A F N Collet Nut Wrench
06101 BT 30 x ER 16 - 70 with hex nut 46 70 20 28 41116 04609
06101-SLOTNUT BT 30 x ER 16 - 70 with slotted nut 46 70 20 32 46116 04613
06102 BT 30 x ER 16 - 60 with hex nut 46 60 20 28 41116 04609
06102-C BT 30 x ER 16 - 60 with dust seal nut 46 60 20 32 41616 04609
06102-DNA BT 30 x ER 16 - 60 with DNA 16 nut 46 60 20 27 27116 DNA16W
06102-SLOTNUT BT 30 x ER 16 - 60 with slotted nut 46 60 20 32 46116 04613
06103 BT 30 x ER 16 - 90 with hex nut 46 90 20 28 41116 04609
06103-SLOTNUT BT 30 x ER 16 - 90 with slotted nut 46 90 20 32 46116 04613
06104 BT 30 x ER 16 - 100 with hex nut 46 100 20 28 41116 04609
06104-SLOTNUT BT 30 x ER 16 - 100 with slotted nut 46 100 20 32 46116 04613
06105 BT 30 x ER 16 - 120 with hex nut 46 120 20 28 41116 04609
06105-SLOTNUT BT 30 x ER 16 - 120 with slotted nut 46 120 20 32 46116 04613
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24.
• Balanced to 25,000 RPM at G2.5
• Inspection report included for accuracy and balance
Note: Measure the "A" dimension with the collet in the nut. Dimensions are in millimeters unless otherwise noted.
7
BT 30 and BT 35 Tool Holders and ER Extensions
Part No. C d I1 L I2 I3 D Set Screw Wrench Nut Type
04889 3/8" ER 8M 100 124 24 6 12 - 04620 M
04891 1/2" ER 11M 140 166.5 26.5 6.6 16 - 04621 M
04893 5/8" ER 11M 140 158.5 18.5 6.6 16 - 04621 M
04895 1/2" ER 16M 140 177 37 10.6 22 - 04622 M
04896 3/4" ER 16M 140 165 25 10.6 22 06083 04622 M
04894 3/4" ER 20M 140 180 40 11.5 28 06083 04623 M
04897 1" ER 20M 140 168 28 11.5 28 06083 04623 M
04898 3/4" ER 25M 100 140 40 12 35 06087 04624 M
04888 1" ER 25M 140 190 50 12 35 06087 04624 M
L
D
l1
d
l3
C
l2
set screw – T
For applications where the extension is rotating, extension length should not exceed a 4:1 ratio Example: 1/2" shank should not extend more than 2" in front of the holder.
ER 8, 11, 16, 20, 25 Straight Shank Extensions
• Works with any tool holder
• Precision ground pocket
• Includes ER mini nut - 0rder high-speed mini nuts pg. 18
Dimensions are in millimeters unless otherwise indicated.
BT 35, ER 32, SYOZ 25 Tool Holders for Heian Routers
Part No. Description D A F N Collet Nut Wrench
06010 BT 35 x SYOZ 25 - 76 with nut 53 76 22 60 included 03691
061-BT35-ER 32 76 BT 35 x ER 32 - 76 53 76 22 50 46132 04616
061-BT35-ER 32 76A BT 35 x ER 32 - 76 with nut 53 76 22 50 included 04616
BT 30, ER 32 Tool Holders
Part No. Description D A F N Collet Nut Wrench
06112 BT 30 x ER 32 - 60 46 60 20 50 46132 04616
06113 BT 30 x ER 32 - 70 46 70 20 50 46132 04616
06113-W-60 BT 30 x ER 32 - 60, 41mm flats - Komo 46 60 20 50 46132 04616
06113-W-60-A BT 30 x ER 32 - 60 w/nut & stud, 41mm flats - Komo 46 60 20 50 46132 04616
06113-W-90 BT 30 x ER 32 - 90 38mm flats - Komo 46 90 20 50 46132 04616
06114 BT 30 x ER 32 - 100 46 100 20 50 46132 04616
06115 BT 30 x ER 40 - 80 46 80 20 63 46132 04616
BT 30, SYOZ 25 Tool Holders
Part No. Description D A F N Collet Nut Wrench
06001-W BT 30 x SYOZ 25 - 70, 38mm flats - Komo 46 70 20 60 included 03691
06001 BT 30 x SYOZ 25 - 70 with nut 46 70 20 60 included 03691
Special sizes made to your specifi cations. See page 42 or call for more information.
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.8
HSK 63F and ISO 30 Arbors for CNC Routers
Part No. Description L GL D B N
12700-40-W ISO 30 x 1-1/4" x 40 arbor 40 42 1-1/4" 20 42
12700-55-W ISO 30 x 1-1/4" x 55 arbor 55 42 1-1/4" 20 42
12700-80-W ISO 30 x 1-1/4" x 80 arbor 80 42 1-1/4" 20 42
12700-100-W ISO 30 x 1-1/4" x 100 arbor 100 42 1-1/4" 20 42
Special sizes made to your specifications. Refer to page 42 or call for details.
• Special 3 screw design improves safety
• Precision ground taper provides high accuracy
• Balanced 25,000 RPM at G2.5
ISO 30 Arbors
Part No. Description D L N B GL
41060 HSK 63F 1-1/4" arbor x 55 1 1/4" 55 42 20 45
41080-3H HSK 63F 1-1/4" arbor x 80 1 1/4" 80 42 20 45
41085 HSK 63F 1-1/4" arbor x 100 1 1/4" 100 42 20 45
41087 HSK 63F 1-1/4" arbor x 112 1 1/4" 112 42 20 45
HSK 63F Arbors
• Special 3 screw design improves safety
• Taper ground to AT3 specification for accuracy
• Balanced 25,000 RPM at G2.5
Dimensions are in millimeters unless otherwise indicated.
Dimensions are in millimeters unless otherwise indicated.
9
High Precision Drill Chucks, Adapters, & CMS Tool Holder
• Capacity from 1/16" to 1/2"
• 4 times greater holding power
• Balanced to 10,000 RPM
Part No. Collet Type Shank Thread
00316-R ER16 3/8" or 10mm Right
00316-L ER16 3/8" or 10mm Left
Part No. Shank Thread I.D.
00316-SLN-R M10x1.05 Right 10
00316-SLN-L M10x1.05 Left 10
Drill AdaptersFor CNC routers with inline multi-spindles.
CMS ToolholderIncludes turret nut. Order collets and nuts separately.
Part No. Description
CMS-RR32 CMS Toolholder with turret nut
• Works with ER or ETS collets
• 0.0002" T.I.R. (collet pocket runout)
• Taper ground to AT3 specification
HP3 Precision Drill Toolholders (ISO, BT, HSK)
Part No. Description d1 I1 G
171.05.046.003 HSK 63F HP3 drill chuck 1/2" 50 123.5 -
64.05.046.051 ISO 30 HP3 drill chuck 1/2" 50 103 M12
67.05.046.001 BT 30 HP3 drill chuck 1/2" 50 92.5 M12
39.05.046.001 BT 40 HP3 drill chuck 1/2" 50 95.5 M16
Turret Nut
Our high-precision drill chucks have the flexibility to hold a wide range of shank sizes and deliver superior performance too. Maximum runout (T.I.R.) is only .0008”. The one-piece design provides greater rigidty and safety because the chuck cannot break free during operation.
• Eliminate threaded drill bits
• Better rigidity and holding power
• Longer drill life
Dimensions are in millimeters unless otherwise indicated.
Dimensions are in millimeters unless otherwise indicated.
Special sizes made to your specifi cations. See page 42 or call for more information.
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.10
HSK 63F and ISO 30 Shrink-Fit Tool Holders for CNC Routers
HSK 63F Shrink-Fit Toolholders
Part No. Description d1 d2 d3 I1 I2
171.05.071.010 HSK 63F x 20 - 100 20 33 42 100 52
171.05.071.011 HSK 63F x 25 - 115 25 44 53 115 63
171.05.071.250 HSK 63F x 1/4" - 80 1/4" 21 27 80 36
171.05.071.375 HSK 63F x 3/8" - 95 3/8" 24 32 95 42
171.05.071.500 HSK 63F x 1/2" - 95 1/2" 24 32 95 47
TE-171.05.071.500-S HSK 63F x 1/2" - 95 Thermwood 1/2" 24 32 95 47
171.05.071.750 HSK 63F x 3/4" - 100 3/4" 33 42 100 52
171.05.072.1 HSK 63F x 1" - 115 1" 44 53 115 53
ISO 30 Shrink-Fit Toolholders
Part No. Description d1 d2 d3 I1 l2
64.05.071.250 ISO 30 x 1/4" - 80 1/4" 18 27 80 39
64.05.071.375 ISO 30 x 3/8" - 80 3/8" 24 32 80 -
64.05.071.500 ISO 30 x 1/2" - 80 1/2" 28 32 80 25
TE-64.05.071.500-S ISO 30 x 1/2" - 80 Thermwood 1/2" 28 32 80 -
64.05 071.625 ISO 30 x 5/8” - 80 5/8" 28 32 80 50
64.05 071.750 ISO 30 x 3/4" - 80 3/4" 36 41 80 -
TE-64.05 071.750-S ISO 30 x 3/4" - 80 Thermwood 3/4" 33 41 80 -
Shrink-fit toolholders provide concentric clamping force of 10,000 lbs or more directly on the tool shank. This is why T.I.R. is so low and operators are able to run faster and cutters last longer too.
• Balanced to 24,000 RPM at G2.5
• Runout (T.I.R.) only .0001"
• Highest rigidity – extends cutter life
Dimensions are in millimeters unless otherwise indicated.
Dimensions are in millimeters unless otherwise indicated.
• Balanced to 24,000 RPM at G2.5
• Runout (T.I.R.) only .0001"
• Highest rigidity – extends cutter life
All Techniks products are backed by our 100% satisfaction guarantee! 11
TechnoSHRINK Induction Heat Shrink-Fit Machines
TechnoSHRINK MachinesPart No. Description Tool Change Cooling Power Rating L x D x H Ship Wt.
00300 Techno-Shrink II 30 seconds air (2-3 min.) 220V, 1 phase 16"x 19"x 28" 33 lbs
00100 Techno-Shrink Ultra 6-9 seconds air (2-3 min.) 220V, 3 phase 16"x 16"x 32" 77 lbs
Tool Holder Spindle Adapters
Part No. Spindle Figure
00151 any 30 taper 2
00152 any 40 taper 1
00153 any 50 taper 1
00156 HSK 32 2
00157 HSK 40 2
00158 HSK 50 2
00159 HSK 63 1
00160 HSK 80 1
TechnoSHRINK II(affordable induction unit for carbide shanks) TechnoSHRINK Ultra (for carbide and steel shanks)
Comes with everything you see in this photo.
• Heats and cools automatically
• Eliminates handling hot tools!
• For shank sizes 1/8" to 1-1/4"
Induction Stop Rings
Part No. Fits Shank Size
00165 3mm - 5mm
00166 6mm - 12mm
00167 14mm - 20mm
00168 25mm - 32mm
Tool Holder Sleeve
Part No. Description
00170 Use with adapters (left)
Supports holder during shrinking
Replacement Parts
Both the TechnoSHRINK machines feature fast, safe, induction heat and automatic cooling using your shop air. Cycle time is automatically set by entering the shank size. Change tools in seconds and cools in minutes.Controls are easy to use and do not require special training.
Figure 1 Figure 2
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.12
Hydraulic Tool Holders for CNC Routers
ISO Hydraulic Chucks for CNC Routers
Part No. Description d1 d2 d3 d I2 I1
64.05.043.224 ISO/SK 30 Hydro Chuck 3/4" ID 3/4" 70 45 50 44 60
64.05.043.225 ISO/SK 30 Hydro Chuck 1" ID 1.0" 70 45 50 44 60
HSK Hydraulic Chucks for CNC Routers
Part No. Description d1 d2 d3 d I2 I1
171.05.036.016 HSK 63 F Hydro Chuck 20mm ID 20 42 50 63 58 100
171.05.036.018 HSK 63 F Hydro Chuck 32mm ID 32 60 50 63 59 125
171.05.036.020 HSK 63 F Hydro Chuck 25mm ID 25 44 50 63 23 85
171.05.036.035 HSK 63 F Hydro Chuck 1" ID 1.0" 44 50 63 23 85
• High holding power, comparable to shrink-fit
• Fast tool changes, simply turn the screw
• Extends tool life of carbide and diamond tooling
• High holding power, comparable to shrink-fit
• Fast tool changes, simply turn the screw
• Extends tool life of carbide and diamond tooling
To use smaller shank sizes and odd shank diameters order reduc-ing sleeves to fit your cutting tools.
Dimensions are in millimeters unless otherwise indicated.
Dimensions are in millimeters unless otherwise indicated.
All Techniks products are backed by our 100% satisfaction guarantee! 13
Reducing Sleeves for Hydraulic Tool Holders
Metric OD / Inch ID
Part No. Description d1 D D1 L L1 L2
05.024.114 20mm OD - 1/4" ID 0.25" 20 24 52.9 50.9 2
05.024.116 20mm OD - 5/16" ID 0.3125" 20 24 52.9 50.9 2
05.024.118 20mm OD - 3/8" ID 0.375" 20 24 52.9 50.9 2
05.024.120 20mm OD - 7/16" ID 0.4375" 20 24 52.9 50.9 2
05.024.122 20mm OD - 1/2" ID 0.5" 20 24 52.9 50.9 2
05.024.126 20mm OD - 5/8" ID 0.625" 20 24 52.9 50.9 2
Metric OD / Metric ID
Part No. Description d1 D D1 L L1 L2
05.024.001 20mm OD - 6mm ID 6 20 24 52.9 50.9 2
05.024.002 20mm OD - 8mm ID 8 20 24 52.9 50.9 2
05.024.003 20mm OD - 10mm ID 10 20 24 52.9 50.9 2
05.024.004 20mm OD - 12mm ID 12 20 24 52.9 50.9 2
05.024.005 20mm OD - 14mm ID 14 20 24 52.9 50.9 2
05.024.006 20mm OD - 16mm ID 16 20 24 52.9 50.9 2
05.024.012 32mm OD - 10mm ID 10 32 40 66 62 4
05.024.013 32mm OD - 12mm ID 12 32 40 66 62 4
05.024.014 32mm OD - 14mm ID 14 32 40 66 62 4
05.024.015 32mm OD - 16mm ID 16 32 40 66 62 4
05.024.016 32mm OD - 18mm ID 18 32 40 66 62 4
05.024.018 32mm OD - 20mm ID 20 32 40 66 62 4
05.024.020 32mm OD - 25mm ID 25 32 40 66 62 4
Inch OD / Inch ID
Part No. Description d1 D D1 L L1 L2
05.024.130 3/4" OD - 1/8" ID 0.125" 0.750" 0.945" 2.083" 2.003" 0.079"
05.024.131 3/4" OD - 3/16" ID 0.1875" 0.750" 0.945" 2.083" 2.003" 0.079"
05.024.132 3/4" OD - 1/4" ID 0.25" 0.750" 0.945" 2.083" 2.003" 0.079"
05.024.133 3/4" OD - 5/16" ID 0.3125" 0.750" 0.945" 2.083" 2.003" 0.079"
05.024.134 3/4" OD - 3/8" ID 0.375" 0.750" 0.945" 2.083" 2.003" 0.079"
05.024.135 3/4" OD - 7/16" ID 0.4375" 0.750" 0.945" 2.083" 2.003" 0.079"
05.024.136 3/4" OD - 1/2" ID 0.5" 0.750" 0.945" 2.083" 2.003" 0.079"
05.024.137 3/4" OD - 5/8" ID 0.625" 0.750" 0.945" 2.083" 2.003" 0.079"
L
• Inch and Metric sizes
• T.I.R. only .00012"
• Fast tool changes
Dimensions are in millimeters unless otherwise indicated.
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.14
ER Precision Inch Collets
ER Precision Collets Inch Size
ER 11 ER 16 ER 20 ER 25 ER 32 ER 40 Range Shank
04211 - 1/16 04216 - 1/16 .043 - .062" 1/16"
04211 - 3/32 04216 - 3/32 04220 - 3/32 04225 - 3/32 04232 - 3/32 .054 - .093" 3/32"
04211 - 1/8 04216 - 1/8 04220 - 1/8 04225 - 1/8 04232 - 1/8 04240 - 1/8 .086 - .125" 1/8"
04211 - 5/32 04216 - 5/32 04220 - 5/32 04225 - 5/32 04232 - 5/32 04240 - 5/32 .117 - .156" 5/32"
04211 - 3/16 04216 - 3/16 04220 - 3/16 04225 - 3/16 04232 - 3/16 04240 - 3/16 .148 - .187" 3/16"
04211 - 7/32 04216 - 7/32 04220 - 7/32 04225 - 7/32 04232 -7/32 04240 - 7/32 .179 - .218" 7/32"
04211 - 1/4 04216 - 1/4 04220 - 1/4 04225 - 1/4 04232 - 1/4 04240 - 1/4 .211 - .250" 1/4"
04216 - 9/32 04220 - 9/32 04225 - 9/32 04232 - 9/32 04240 - 9/32 .242 - .281" 9/32"
04216 - 5/16 04220 - 5/16 04225 - 5/16 04232 - 5/16 04240 - 5/16 .273 - .312" 5/16"
04216 - 11/32 04220 - 11/32 04225 - 11/32 04232 - 11/32 04240 - 11/32 .304 - .343" 11/32"
04216 - 3/8 04220 - 3/8 04225 - 3/8 04232 - 3/8 04240 - 3/8 .336 - .375" 3/8"
04216 - 13/32 04220 - 13/32 04225 - 13/32 04232 - 13/32 04240 - 13/32 .367 - .406" 13/32"
04220 - 7/16 04225 - 7/16 04232 - 7/16 04240 - 7/16 .398 - .437" 7/16"
04220 - 15/32 04225 - 15/32 04232 - 15/32 04240 - 15/32 .429 - .468" 15/32"
04220 - 1/2 04225 - 1/2 04232 - 1/2 04240 - 1/2 .461 - .500" 1/2"
04225 - 17/32 04232 - 17/32 04240 - 17/32 .492 - .531" 17/32"
04225 - 9/16 04232 - 9/16 04240 - 9/16 .523 - .562" 9/16"
04225 - 19/32 04232 - 19/32 04240 - 19/32 .554 - .593" 19/32"
04225 - 5/8 04232 - 5/8 04240 - 5/8 .586 - .625" 5/8"
04232 - 21/32 04240 - 21/32 .617 - .656" 21/32"
04232 - 11/16 04240 - 11/16 .648 - .687" 11/16"
04232 - 23/32 04240 - 23/32 .679 - .718" 23/32"
04232 - 3/4 04240 - 3/4 .711 - .750" 3/4"
04240 - 7/8 .836 - .875" 7/8"
04240 - 1 .961 - 1.00" 1"
Our ER collets are the best in the industry. They are made from high-carbon bearing steel that is heat-treated for improved flexibility and longer life. Each collet is precisely ground and honed using a swiss technique, then individu-ally inspected and tested for quality. Compatible with DR, RD, ESX, AR, & BR series collets. For best rigidity and cutter life use Power Coat nuts (pg 17).
• Runout (T.I.R.) only .0002"
• Collapse range: 0.039"
• Collet sets availableCall to order collet sets.
All Techniks products are backed by our 100% satisfaction guarantee! 15
ER Precision Metric Collets
ER 16, 20, 25, 32, 40, Precision Metric Collets
ER 16 ER 20 ER 25 ER 32 ER 40 Inch Range Metric
04216 - 01 1/32" .019 - .039" 0.5-1
04216 - 02 04220 - 02 04225 - 02 1/16" .039 - .079" 1-2
04216 - 03 04220 - 03 04225 - 03 04232 - 03 7/64" .079 - .118" 2-3
04216 - 04 04220 - 04 04225 - 04 04232 - 04 04240 - 04 1/8" .118 - .157" 3-4
04216 - 05 04220 - 05 04225 - 05 04232 - 05 04240 - 05 3/16" .157 - .197" 4-5
04216 - 06 04220 - 06 04225 - 06 04232 - 06 04240 - 06 7/32" .197 - .236" 5-6
04216 - 07 04220 - 07 04225 - 07 04232 - 07 04240 - 07 1/4" .236 - .276" 6-7
04216 - 08 04220 - 08 04225 - 08 04232 - 08 04240 - 08 5/16" .276 - .315" 7-8
04216 - 09 04220 - 09 04225 - 09 04232 - 09 04240 - 09 11/32" .315 - .354" 8-9
04216 - 10 04220 - 10 04225 - 10 04232 - 10 04240 - 10 3/8" .354 - .394" 9-10
04220 - 11 04225 - 11 04232 - 11 04240 - 11 13/32" .394 - .433" 10-11
04220 - 12 04225 - 12 04232 - 12 04240 - 12 7/16" .433 - .472" 11-12
04220 - 13 04225 - 13 04232 - 13 04240 - 13 1/2" .472 - .512" 12-13
04225 - 14 04232 - 14 04240 - 14 17/32" .512 - .551" 13-14
04225 - 15 04232 - 15 04240 - 15 9/16" .551 - .591" 14-15
04225 - 16 04232 - 16 04240 - 16 5/8" .591 - .630" 15-16
04232 - 17 04240 - 17 21/32" .630 - .669" 16-17
04232 - 18 04240 - 18 11/16" .669 - .709" 17-18
04232 - 19 04240 - 19 3/4" .709 - .748" 18-19
04232 - 20 04240 - 20 25/32" .748 - .787" 19-20
04240 - 21 13/16" .787 - .827" 20-21
04240 - 22 27/32" .827 - .866" 21-22
04240 - 23 7/8" .866 - .906" 22-23
04240 - 24 15/16" .906 - .945" 23-24
04240 - 25 31/32" .945 - .984" 24-25
04240 - 26 1" .984 - 1.024" 25-26
Note: 0.5mm increment collets are available on request.
ER 8, ER 11, Precision Metric Collets
ER 8 ER 11 Inch Range Metric
04208 - 01.0 04211 - 01.0 1/32" .019 - .039" 0.5 - 1.0
04208 - 01.5 04211 - 01.5 3/64" .039 - .059" 1.0 - 1.5
04208 - 02.0 04211 - 02.0 1/16" .059 - .079" 1.5 - 2.0
04208 - 02.5 04211 - 02.5 3/32" .079 - .098" 2.0 - 2.5
04208 - 03.0 04211 - 03.0 7/64" .098 - .118" 2.5 - 3.0
04208 - 03.5 04211 - 03.5 1/8" .118 - .138" 3.0 - 3.5
04208 - 04.0 04211 - 04.0 5/32" .138 - .157" 3.5 - 4.0
04208 - 04.5 04211 - 04.5 11/64" .157 - .177" 4.0 - 4.5
04208 - 05.0 04211 - 05.0 3/16" .177 - .197" 4.5 - 5.0
04211 - 05.5 13/64" .197 - .217" 5.0 - 5.5
04211 - 06.0 7/32" .217 - .236" 5.5 - 6.0
04211 - 06.5 1/4" .236 - .256" 6.0 - 6.5
04211 - 07.0 17/64" .256 - .276" 6.5 - 7.0
Our ER collets are made from high-carbon bearing steel that is heat-treated for improved flexibility and longer life. Each collet is precisely ground and honed using a swiss technique, then individually inspected and tested for quality. Compatible with DR, RD, ESX, AR, & BR series collets.
• Runout (T.I.R.) .0002"
• Collapse range: 0.039"
• Collet sets available
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.16
Rubber bearing seals fail,
then dust contaminates
bearings, making them seize.
Uncoated threads limit
holding power.
Bearing Nuts = Old Technology
Why CNC Routers Run Better with Power Coat Nuts
Power Coat nuts are manufac-
tured with a special process
that reduces friction between
the nut, collet shoulder, and
tool holder threads. This great-
ly increases holding power so
runout (T.I.R.) is improved. Bet-
ter T.I.R. means cutting is faster
and smoother and tool life is
improved too.
Power Coat Nuts = 40% More Holding Power Than Bearing Nuts
Power Coat nuts perform the job of keeping your toolholder assembly intact and cutting true under extreme load conditions.
Bearing nuts cannot be
balanced because they
have moving parts, so
cutting tools wear
prematurely.
See a video demonstrating how Power Coat nuts hold
tighter to improve CNC router performance and shop
safety at: www.techniksusa.com/pcnut
• Less runout (T.I.R.)
• Greater rigidity (accuracy)
• Better balance (no moving parts)
collet shoulder
threads
All Techniks products are backed by our 100% satisfaction guarantee! 17
Ultra High Speed Power Coat ER Collet Nuts
Ultra High-Speed ER Coated Nuts
Part No. Description D B M Max. Speed Wrench * Max. Torque
46111 ER RH 11 B Nut 19 11.8 M14 x 0.75 70,000 04608 20 ft/lbs
46116 ER RH 16 B Nut 32 18.0 M22 x 1.5 65,000 04613 50 ft/lbs
46120 ER RH 20 B Nut 35 19.5 M25 x 1.5 60,000 04614 75 ft/lbs
46125 ER RH 25 B Nut 42 20.5 M32 x 1.5 55,000 04615 95 ft/lbs
46132 ER RH 32 B Nut 50 23.0 M40 x 1.5 50,000 04616 125 ft/lbs
46140 ER RH 40 B Nut 63 26.0 M50 x 1.5 40,000 04617 140 ft/lbs
*Recommended torque is 80-90% of maximum value. See page 29 for torque wrench.
• 40% more holding power than bearing nuts
• Safer: cutting tool is less likely break free
• Balanced up to 70,000 RPM
80 90 100 110 120 130 140
Standard nut breaks free at 80 ft/lbs
Bearing Nut breaks free at 100 ft/lbs25% more holding power
TEST RESULTS - Nut ComparisonAll nuts torqued to 70 ft/lbs
Holding Power - Foot/Pounds Torque
Power Coat breaks free at 140 ft/lbs 40% more holding power than
bearing nuts provide!
Dimensions are in millimeters.
Because holding power is 40% better than bearing nuts accuracy, cutter performance, saftey, and tool life are all improved!
Power Coat nuts increase hold-ing power because they reduce friction between the nut and the collet shoulder, and the tool holder threads and the nut. This creates more downforce on the collet, making it collapse tighter around the tool shank.
Power Coat breaks free at 140 ft/lbs 40% more holding power than
bearing nuts provide!
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.18
ER Bearing Nuts and High Speed Mini Nuts
ER Bearing Nuts
Part No. Description D B M Wrench * Max. Torque
29132 ER 32 HS Bearing Nut 50 25 M40x1.5 04616 125 ft/lbs
21240 ER 40 HS Bearing Nut 63 28 M50x1.5 04617 140 ft/lbsUse these nuts for spindle speeds below 18,000 RPM’s* Recommended torque is 80-90% of maximum value
Bearing nuts reduce friction between the nut and the collet shoulder. This creates more downforce on the collet, making it collapse tighter around the tool shank.For maximum holding power use Power Coat nuts.
Use ER High Speed mini nuts for applications where speed exceeds 10,000 RPM’s. They are balanced to G2.5 for 20,000 RPM’s. For col-let holders and multi-spindle heads where center or shoulder distances are important.
ER High Speed Mini Nuts
Part No. Description D B M Wrench Max. Torque
33108 ER 8 HS Mini Nut 12 11 M10 x 0.75 04620 7 ft/lbs
33111 ER 11 HS Mini Nut 16 12 M13 x 0.75 04621 14 ft/lbs
33116 ER 16 HS Mini Nut 22 18 M19 x 1.0 04622 22 ft/lbs
33120 ER 20 HS Mini Nut 28 19.5 M24 x 1.0 04623 25 ft/lbs
33125 ER 25 HS Mini Nut 35 21 M30 x 1.0 04624 29 ft/lbs
33125-L ER25 HS L-Hand Nut 35 21 M30 x 1.0 04624 29 ft/lbs
Recommended torque is 80-90% of maximum value. See page 26 for dust seals.
These nuts use a special wrench to torque down the nut. Do not over tighten these nuts.
Dimensions are in millimeters.
Dimensions are in millimeters.
• Bearings reduce friction between collet and nut
• 25% more holding power than standard nuts
• Helps prolong tool life
• Balanced 20,000 RPM at G 2.5
• Narrow nose diameter
• Left hand nut available
All Techniks products are backed by our 100% satisfaction guarantee! 19
Power Coat ER Dust Seal Nuts – Bearing ER Dust Seal Nuts
Power Coat ER Internal Dust Seal Nuts
Part No. Description D B Wrench T * Max. Torque
41616 ER 16 HS Internal Dust Seal Coated Nut 32 22.5 04613 M22x1.5 50 ft/lbs
41620 ER 20 HS Internal Dust Seal Coated Nut 35 24 04614 M25x1.5 75 ft/lbs
41625 ER 25 HS Internal Dust Seal Coated Nut 42 25 04615 M32x1.5 95 ft/lbs
41632 ER 32 HS Internal Dust Seal Coated Nut 50 27.5 04616 M40x1.5 125 ft/lbs
41640 ER 40 HS Internal Dust Seal Coated Nut 63 30.7 04617 M50x1.5 140 ft/lbs
See page 26 for dust seals.
Bearing ER Internal Dust Seal Nuts
Part No. Description D B M Wrench * Max. Torque
21325 ER 25 Internal Dust Seal Bearing Nut 42 22.5 M32x1.5 04615 95 ft/lbs
21332 ER 32 Internal Dust Seal Bearing Nut 50 25 M40x1.5 04616 125 ft/lbs
21340 ER 40 Internal Dust Seal Bearing Nut 63 28 M50x1.5 04617 140 ft/lbs
Recommended torque is 80-90% of maximum value. See page 26 for dust seals.
Use these nuts with a dust seal that snaps into the nut to seal and protect your tools. (pg. 26) They are available for a wide range of diameters. Each dust seal has a .020" range.
Dimensions are in millimeters.
• 40% more holding power than bearing nuts!
• Prevent contamination of collets
• Prolongs tool life
Use these nuts with a dust seal that snaps into the nut to seal and protect your tools. The dust seals can be found on page 26. They are available for a wide range of diameters. Each dust seal has a .020" range.
Dimensions are in millimeters.
• Prevent contamination of collets
• Prolongs tool life
• Helps keep tool holder clean
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.20
TG 75 and TG 100 Precision Collets
Part No. ID Size
04010 - 3/32 3/32"
04010 - 1/8 1/8"
04010 - 5/32 5/32"
04010 - 3/16 3/16"
04010 - 7/32 7/32"
04010 - 1/4 1/4"
04010 - 9/32 9/32"
04010 - 5/16 5/16"
04010 - 11/32 11/32"
04010 - 3/8 3/8"
TG 100 Collets
Part No. ID Size
04010 - 13/32 13/32"
04010 - 7/16 7/16"
04010 - 15/32 15/32"
04010 - 1/2 1/2"
04010 - 17/32 17/32"
04010 - 9/16 9/16"
04010 - 19/32 19/32"
04010 - 5/8 5/8"
04010 - 21/32 21/32"
04010 - 11/16 11/16"
Part No. ID Size
04010 - 23/32 23/32"
04010 - 3/4 3/4"
04010 - 25/32 25/32"
04010 - 13/16 13/16"
04010 - 27/32 27/32"
04010 - 7/8 7/8"
04010 - 29/32 29/32"
04010 - 15/16 15/16"
04010 - 31/32 31/32"
04010 - 1 1"
Part No. ID Size
04008 - 7/16 7/16"
04008 - 15/32 15/32"
04008 - 1/2 1/2"
04008 - 17/32 17/32"
04008 - 9/16 9/16"
04008 - 19/32 19/32"
04008 - 5/8 5/8"
04008 - 21/32 21/32"
04008 - 11/16 11/16"
04008 - 23/32 23/32"
04008 - 3/4 3/4"
TG 75 Collets
Part No. ID Size
04008 - 3/32 3/32"
04008 - 1/8 1/8"
04008 - 5/32 5/32"
04008 - 3/16 3/16"
04008 - 7/32 7/32"
04008 - 1/4 1/4"
04008 - 9/32 9/32"
04008 - 5/16 5/16"
04008 - 11/32 11/32"
04008 - 3/8 3/8"
04008 - 13/32 13/32"
Dimensions
Series L A
TG 75 1.844" 1.062"
TG 100 2.375" 1.379"
TG 75 Collet
TG 100 Collet
Snap collet into the nut before screwing nut onto spindle or collet holder.
• Runout (T.I.R.) .0004"
• Collapse range: 1/64"
• Collet sets available
Our TG collets are made from high-carbon bearing steel that is heat-treated for improved flexibility and longer life.
Each collet is precisely ground and honed using a swiss technique, then individually inspected and tested for quality.
All Techniks products are backed by our 100% satisfaction guarantee! 21
Power Coat TG Collet Nuts and TG Dust Seal Collet Nuts
TG Dust Seal Collet Nuts
Part No. Description D d1 T I1 L Spanner Torque*
28210 TG100 Dust Seal Nut 2.35" 0.95" 1 7/8 - 12" 0.44" 1.41" 03691 100 ft/lb
* Recommended torque is 80-90% of maximum value. See page 29 for torque wrench.
Power Coat nuts increase hold-ing power because they reduce friction between the nut and the collet shoulder, and the tool holder threads and the nut. This creates more downforce on the collet, making it collapse tighter around the tool shank.
Use TG 100 dust cover style nuts (bottom) to prevent contamination of collet with dust and particles.
Dust Cover Style
TG Collet Nuts
Part No. Description D d1 T I1 L Spanner Torque*
27500 TG75 Collet Nut 1.88" - 1 1/2 - 12" 0.32" 0.94" 04018 100 ft/lb
28110 TG100 Collet Nut 2.35" 1.12" 1 7/8 - 12" 0.44" 1.18" 03691 100 ft/lb
* Recommended torque is 80-90% of maximum value. See page 29 for torque wrench.
Power Coat nuts increase holding power because they reduce friction between the nut and the collet shoul-der, and the tool holder threads and the nut. This cre-ates more downforce on the collet, making it collapse tighter around the tool shank.
Regular Style
• Prevent contamination of collets
• Helps keep tool holder clean
• Power Coat provides 40% better holding power
• Power Coat for 40% more holding power
• No bearings to seize and fail
• Balanced up to 20,000 RPM
Use these nuts with a dust seal that snaps into the nut to seal and protect your tools. The dust covers can be found on page 26.
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.22
Shoda Collets and Nuts
Shoda Collet Nuts
Shoda ColletsPart Number Description A d L
SD-20mm-.250 Shoda 20mm (old style) 1/4" collet 20 .250" 52
SD-20mm-.312 Shoda 20mm (old style) 5/16" collet 20 .312" 52
SD-20mm-.375 Shoda 20mm (old style) 3/8" collet 20 .375" 52
SD-20mm-.500 Shoda 20mm (old style) 1/2" collet 20 .500" 52
SD-20mm-.625 Shoda 20mm (old style) 5/8" collet 20 .625" 52
SD-C001-.125 Shoda Piggyback 1/8" collet 16 .125" 52
SD-C001-.187 Shoda Piggyback 3/16" collet 16 .187" 52
SD-C001-.250 Shoda Piggyback 1/4" collet 16 .250" 52
SD-C001-.312 Shoda Piggyback 5/16" collet 16 .312" 52
SD-C001-.375 Shoda Piggyback 3/8" collet 16 .375" 52
SD-C001-.500 Shoda Piggyback 1/2" collet 16 .500" 52
SD-C015-.125 Shoda 24mm (new style) 1/8" collet 24 .125" 52
SD-C015-.250 Shoda 24mm (new style) 1/4" collet 24 .250" 52
SD-C015-.312 Shoda 24mm (new style) 5/16" collet 24 .312" 52
SD-C015-.375 Shoda 24mm (new style) 3/8" collet 24 .375" 52
SD-C015-.500 Shoda 24mm (new style) 1/2" collet 24 .500" 52
SD-C015-.625 Shoda 24mm (new style) 5/8" collet 24 .625" 52
SD-C015-.750 Shoda 24mm (new style) 3/4" collet 24 .750" 52
SS-22-1/4 Super Shoda 1/4" collet 23 1/4" 40
SS-22-3/8 Super Shoda 3/8" collet 23 3/8" 40
SS-22-10 Super Shoda 10mm collet 23 10 40
SS-22-1/2 Super Shoda 1/2" collet 23 1/2" 40
Note: Other sizes available on request.
Part Number Description A d L
SD-C001-Nut Shoda piggy back collet nut 36 14 30
SD-20mm-Nut Shoda old style collet nut 41 19 30
SD-C015-Nut Shoda new style collet nut 46 22 30
SS-22-Nut Super Shoda collet nut 36 12.5 15
SS-22-Ext -Nut Super Shoda extended nut 36 12.5 30
Our Shoda collets are the most accurate in the industry. We use heat-treated high carbon bearing steel and a Swiss grinding technique that ensures accuracy.
Shoda SD collet
Super Shoda SS collet
• Precision ground accuracy
• Heat-treated carbon steel
• Individually inspected
Dimensions are in millimeters unless otherwise indicated.
Dimensions are in millimeters.
Old Style Piggyback Style New Style Super Shoda
Super Shoda nut
New style nut
All Techniks products are backed by our 100% satisfaction guarantee! 23
Perske DIN 6388 Collets and Nuts
Perske Collets
EOC 08 SYOZ 20/EOC 12 EOC 16 SYOZ 25 Shank
03508-1/8 03520-1/8 03531-1/8 03868-1/8 1/8"
03508-3/16 03520-3/16 03531-3/16 03868-3/16 3/16"
03508-1/4 03520-1/4 03531-1/4 03868-1/4 1/4"
03508-5/16 03520-5/16 03531-5/16 03868-5/16 5/16"
03520-3/8 03531-3/8 03868-3/8 3/8"
03520-7/16 03531-7/16 03868-7/16 7/16"
03520-1/2 03531-1/2 03868-1/2 1/2"
03531-9/16 03868-9/16 9/16"
03531-5/8 03868-5/8 5/8"
03868-3/4 3/4"
03868-7/8 7/8"
03868-1 1"
03520-10 03531-10 03868-10 10mm
03531-16 03868-16 16mm
03868-20 20mm
03868-25 25mm
Perske Nuts and Wrenches
Part No. Type L D Wrench
03508 EOC 08 19 30 -
03636 EOC 16 24 43 -
03520 SYOZ 20/EOC 12 20 35 22220
03638 SYOZ 25 30 60 03691
Dimensions
Part No. L D
EOC 08 26mm 14.4mm
EOC 16 40mm 25.5mm
SYOZ 20 34mm 20mm
SYOZ 25 52mm 35mm
These Perske collets are made from high-carbon bearing steel that is heat-treated for improved flexibility and longer life.
Each collet is precisely ground and honed using a swiss technique, then individually inspected and tested for quality.
Snap collet into the nut before screwing nut onto spindle or collet holder.
• Runout (T.I.R.) .0004"
• Collapse range: 1/64"
• Made to DIN 6388 standards
Dimensions are in millimeters.
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.24
DNA – Dead Nuts Accurate – ER 16 Collets and Nuts
Designed to hold tighter with greater rigidity for improved T.I.R. and tool life.
DNA Ultra-Precision Metric Collets
Part No Description - Shank Inch Shank Collapse
1016.0030 DNA 16 0.3 - 0.2 mm .0118 – .0079" 0.10 mm
1016.0040 DNA 16 0.4 - 0.3 mm .0157 – .0118" 0.10 mm
1016.0050 DNA 16 0.5 - 0.4 mm .0197 – .0157" 0.10 mm
1016.0060 DNA 16 0.6 - 0.5 mm .0236 – .0196" 0.10 mm
1016.0080 DNA 16 0.8 - 0.7 mm .0315 – .0276" 0.10 mm
1016.0100 DNA 16 1.0 - 0.9 mm .0394 – .0354" 0.10 mm
1016.0120 DNA 16 1.2 - 1.1 mm .0472 – .0433" 0.10 mm
1116.0125 DNA 16 1.25 - 1.00 mm .0492 – .0394" 0.25 mm
1116.0150 DNA 16 1.50 - 1.25 mm .0590 – .0492" 0.25 mm
1116.0175 DNA 16 1.75 - 1.50 mm .0688 – .0590" 0.25 mm
1116.0200 DNA 16 2.00 - 1.75 mm .0787 – .0688" 0.25 mm
1116.0225 DNA 16 2.25 - 2.00 mm .0885 – .0787" 0.25 mm
1116.0250 DNA 16 2.50 - 2.25 mm .0984 – .0885" 0.25 mm
1116.0300 DNA 16 3.00 - 2.50 mm .1181 – .0984" 0.50 mm
1116.0350 DNA 16 3.50 - 3.00 mm .1337 – .1181" 0.50 mm
1116.0400 DNA 16 4.00 - 3.50 mm .1574 – .1337" 0.50 mm
1116.0450 DNA 16 4.50 - 4.0 mm .1771 – .1574" 0.50 mm
1116.0500 DNA 16 5.00 - 4.00 mm .1968 – .1574" 1.0 mm
1116.0600 DNA 16 6.00 - 5.00 mm .2362 – .1968" 1.0 mm
1116.0700 DNA 16 7.00 - 6.00 mm .2755 – .2362" 1.0 mm
1116.0800 DNA 16 8.00 - 7.00 mm .3149 – .2755" 1.0 mm
1116.0900 DNA 16 9.00 - 8.00 mm .3543 – .3149" 1.0 mm
1116.1000 DNA 16 10.0 - 9.00 mm .3927 – .3543" 1.0 mm
DNA Ultra-Precision Inch Collets
Part No Description - Shank Inch Shank Collapse
1116.0018 DNA 16 1/8" .1250 – .1050" 0.50 mm
1116.0316 DNA 16 3/16" .1875 – .1675" 0.50 mm
1116.0014 DNA 16 1/4" .250 – .230" 0.50 mm
1116.0038 DNA 16 3/8" .375 – .355" 0.50 mm
DNA Collets Feature
• 0.0002" T.I.R.
• Best collet for tools 6mm and smaller
• Works with standard ER 16 holders
DNA Collet Nuts, Sealed Nuts, Wrenches
Part No Description
2016-200 DNA16 M19 x1 Mini Nut
27116 M22 x 1.5 nut
27216 M22 x 1.5 nut 1/8" o-ring
27116-30 3.0 - 2.5mm sealed nut
27116-40 4.0 - 3.5mm sealed nut
27116-45 4.5 - 4.0mm sealed nut
27116-50 5.0 - 4.5mm sealed nut
27116-55 5.5 - 5.0mm sealed nut
27116-60 6.0 - 5.5mm sealed nut
27116-65 6.5 - 6.0mm sealed nut
DNA16W DNA 16 Collet Wrench
DNA16-TWA DNA 16 Torque Wrench Adapter
894-22 DNA 16 Mini Nut Wrench
Sealed nuts prevent contamination. Nut O.D. = 27mm
For improved concentricity and consistent T.I.R. 6mm and under, use DNA collets in place of ER 16 collets.
DNA Nut
DNA Sealed Nut
DNA wrench & torque wrench adapter
DNA ColletER Collet
Twice as muchmetal holding
tool shank!
All Techniks products are backed by our 100% satisfaction guarantee! 25
Retention Knobs for CNC Routers and Special Orders
Retention knobs make the important connection between the spindle and the tool holder. Always use the correct retention knob for your tool holder and machine spindle and tighten it properly. Refer to the diagram (right).
Retention Knobs
Part No. Type D d1 d2 d3 L I1 I2 θ T
750-19 KOMO ISO/BT30-A 12.5 17 13 9 12.5 44 23.4 18.2 15° M12
13001 DAT 30- A 17 13 9 13 44 24 19 15° M12
13003 DAT 40 – A 23 19 14 17 54 26 20 15° M16
13001-45 Colombo ISO 30 - Ball 17 12.8 9 13 44 24 19 45° M12
49019 HSD ISO 30 17 12 8 13 44 23.9 - radius M12
07801 BT 30 - 45° 16.5 11 7 12.5 43 23 - 45° M12
07806 BT 30 - 60° 16.5 11 7 12.5 43 23 - 60° M12
07812 BT30 - 90° 16.5 11 7 12.5 43 23 8 M12
4403502 BT 35- Heian 20 13 8.5 12.5 43 28 22.5 - M12
13003 DAT 40 – A 23 19 14 17 54 26 20 15° M16
07803 BT40 - 45° 23 15 10 17 60 35 28 - M16
07808 BT40 - 60° 23 15 10 17 60 35 28 - M16
07814 BT40 - 90° 23 15 10 17 60 35 28 - M16
13001 – Colombo Spindles (Billet spindle) 13001-45 – Colombo spindle clamping by balls (RS spindle)
750-19 – KOMO router for BT 30 tool holder, 13019 – HSD spindles
Stud Machine d1 d2 I1 I2 θ T
Special Pull Studs
We can get the pull studs you need. Just fill in your pull stud(s) dimensions on the chart below before you call. Keep your information in this catalog for easy re-orders.For safe operation please make sure that the pull stud you order is the exact pull stud your machine uses. Improper choice of pull stud can cause damage to the spindle and/or toolholder, and is a potential safety hazard.
T
d3D
d2
d1
l2
Ll1
T
d3D
d2
d1
l2l1
Dimensions are in millimeters.
For safe operation please make sure that the pull stud you order is the exact pull stud your machine uses. Improper choice of pull stud can cause damage to the spindle and/or toolholder, and is a potential safety hazard.
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.26
Internal Dust Seals for ER 16 to ER 40 Collets
ER 16 ER 20 ER 25 ER 32 ER 40 Metric Shank Inch Shank08516 - 03.5 08520 - 03.5 08525 - 03.5 08532 - 03.5 08540- 03.5 3.5 - 3.0 1/8"08516 - 04.0 08520 - 04.0 08525 - 04.0 08532 - 04.0 08540 - 04.0 4.0 - 3.5 5/32"08516 - 04.5 08520 - 04.5 08525 - 04.5 08532 - 04.5 08540 - 04.5 4.5 - 4.0 11/64"08516 - 05.0 08520 - 05.0 08525 - 05.0 08532 - 05.0 08540 - 05.0 5.0 - 4.5 3/16"08516 - 05.5 08520 - 05.5 08525 - 05.5 08532 - 05.5 08540 - 05.5 5.5 - 5.0 13/64"08516 - 06.0 08520 - 06.0 08525 - 06.0 08532 - 06.0 08540 - 06.0 6.0 - 5.5 7/32"08516 - 06.5 08520 - 06.5 08525 - 06.5 08532 - 06.5 08540 - 06.5 6.5 - 6.0 1/4"08516 - 07.0 08520 - 07.0 08525 - 07.0 08532 - 07.0 08540 - 07.0 7.0 - 6.5 17/64"08516 - 07.5 08520 - 07.5 08525 - 07.5 08532 - 07.5 08540 - 07.5 7.5 - 7.0 9/32"08516 - 08.0 08520 - 08.0 08525 - 08.0 08532 - 08.0 08540 - 08.0 8.0 - 7.5 5/16"08516 - 08.5 08520 - 08.5 08525 - 08.5 08532 - 08.5 08540 - 08.5 8.5 - 8.0 21/64"08516 - 09.0 08520 - 09.0 08525 - 09.0 08532 - 09.0 08540 - 09.0 9.0 - 8.5 11/32"08516 - 09.5 08520 - 09.5 08525 - 09.5 08532 - 09.5 08540 - 09.5 9.5 - 9.0 3/8"08516 - 10.0 08520 - 10.0 08525 - 10.0 08532 - 10.0 08540 - 10.0 10.0 - 9.5 25/64"
08520 - 10.5 08525 - 10.5 08532 - 10.5 08540 - 10.5 10.5 - 10.0 13/32"08520 - 11.0 08525 - 11.0 08532 - 11.0 08540 - 11.0 11.0 - 10.5 27/64"08520 - 11.5 08525 - 11.5 08532 - 11.5 08540 - 11.5 11.5 - 11.0 7/16"08520 - 12.0 08525 - 12.0 08532 - 12.0 08540 - 12.0 12.0 - 11.5 15/32"08520 - 12.5 08525 - 12.5 08532 - 12.5 08540 - 12.5 12.5 - 12.0 31/64"08520 - 13.0 08525 - 13.0 08532 - 13.0 08540 - 13.0 13.0 - 12.5 1/2"
08525 - 13.5 08532 - 13.5 08540 - 13.5 13.5 - 13.0 17/32"08525 - 14.0 08532 - 14.0 08540 - 14.0 14.0 - 13.5 35/64"08525 - 14.5 08532 - 14.5 08540 - 14.5 14.5 - 14.0 9/16"08525 - 15.0 08532 - 15.0 08540 - 15.0 15.0 - 14.5 37/64"08525 - 15.5 08532 - 15.5 08540 - 15.5 15.5 - 15.0 19/32"08525 - 16.0 08532 - 16.0 08540 - 16.0 16.0 - 15.5 5/8"
08532 - 16.5 08540 - 16.5 16.5 - 16.0 41/64"08532 - 17.0 08540 - 17.0 17.0 - 16.5 21/32"08532 - 17.5 08540 - 17.5 17.5 - 17.0 11/16"08532 - 18.0 08540 - 18.0 18.0 - 17.5 45/64"08532 - 18.5 08540 - 18.5 18.5 - 18.0 23/32"08532 - 19.0 08540 - 19.0 19.0 - 18.5 3/4"08532 - 19.5 08540 - 19.5 19.5 - 19.0 49/64"08532 - 20.0 08540 - 20.0 20.0 - 19.5 25/32"
08540 - 20.5 20.5 - 20.0 51/64"08540 - 21.0 21.0 - 20.5 13/16"08540 - 21.5 21.5 - 21.0 27/32"08540 - 22.0 22.0 - 21.5 55/64"08540 - 22.5 22.5 - 22.0 7/8"08540 - 23.0 23.0 - 22.5 29/32"08540 - 23.5 23.5 - 23.0 59/64"08540 - 24.0 24.0 - 23.5 15/16"08540 - 24.5 24.5 - 24.0 61/64"08540 - 25.0 25.0 - 24.5 31/32"08540 - 25.5 25.5 - 25.0 1"
Seal fits inside nut before assembling with collet.
Ranges are in millimeters.Internal Dust Seals
• Eliminates cleaning collets!
• Extends the life of your collets
• Use with Dust Cover Nuts (pgs. 19, 21)
All Techniks products are backed by our 100% satisfaction guarantee! 27
External Dust Covers For Tool Shanks – Spindle Wipers
• Eliminates cleaning collets!
• Extends the life of your collets
• Extends tool life by maintaining T.I.R.
For 3/16" thru 3/4" tool shanks.Works with: TG 75, TG 100, ER 25, ER 32, ER 40, SYOZ 25, SD-CO15, SD-20MM
Part No. Description
DC32-3/16 Dust cover for 3/16" tool shank
DC32-1/4 Dust cover for 1/4" tool shank
DC32-5/16 Dust cover for 5/16" tool shank
DC32-3/8 Dust cover for 3/8" tool shank
DC32-1/2 Dust cover for 1/2" tool shank
DC32-5/8 Dust cover for 5/8" tool shank
DC32-3/4 Dust cover for 3/4" tool shank
Installed Dust Seal
Simple and effective dust covers prevent costly failures and reduce downtime by keeping unwanted particles from entering the collet pocket.
Keeping your tool holder clean insures proper balance, maximizes grip on tool shank, and reduces downtime spent cleaning out collets during tool changes.
Installation
1. Place dust cover on tool shank
2. Insert tool into collet/nut assembly
3. Tighten assembly into toolholder using proper torque
Note: Do not slide dust cover over cutting edge of tool or you may damage the dust cover.
Real lambskin provides the best cleaning. Use with any type of machine with a taper of 7/24 CAT, BT or DIN 69871.
Part No. Taper Total Taper
17706 30 170 60
17707 40 188 78
17708 50 240 120
07710 HSK 63A 165 31
07711 HSK 63F 165 31
Spindle Wipers
External Dust Covers
• For CAT, BT, HSK spindles
• Remove contaminants to improve T.I.R.
• Keeps spindles and tool holders clean
Dimensions are in millimeters.
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.28
Type A, UM, RU, and M Wrenches
Part No. Description Nut Type Length Width
04608 ER 11-A Wrench A (Hex) 120 40
04609 ER 16-A Wrench A (Hex) 140 53
04610 ER 20-A Wrench A (Hex) 160 60
04613 ER 16-E Wrench Slotted 160 55
04614 ER 20-E Wrench Slotted 180 60
04615 ER 25-E Wrench Slotted 206 65
04616 ER 32-E Wrench Slotted 253 75
04617 ER 40-E Wrench Slotted 289 90
04618 ER 50-E Wrench Slotted 351 110
04620 ER 8-M Wrench ER Mini 75 13
04621 ER 11-M Wrench ER Mini 95 17
04622 ER 16-M Wrench ER Mini 117 22.5
04623 ER 20-M Wrench ER Mini 129 28.5
04624 ER 25-M Wrench ER Mini 142.5 35.5
04018 TG 75 Wrench Hook Type 253 46
03691 TG 100 / SYOZ 25 Wrench Hook Type 260 46
22220 SY0Z 20 Wrench Hook Type 34
Note: Proper torque on the collet nut reduces collet wear, keeps tools securely in tool holder and saves you time and money. See the Recommended Torque Chart on the back cover for proper torque values.Torque down the nut to 80-90% of maximum torque value. Do not over tighten nuts as this will prematurely cause collets for fail and damage tool holder.
ER 20A Hex Wrench
ER 20E Slotted Wrench
TG Hook Wrench
DIN 894 Hex Wrench
ER 20 Mini Wrench
Use a tightening fixture to secure the tool holder. (pg. 30)
Hand Wrenches
Dimensions are in millimeters.
All Techniks products are backed by our 100% satisfaction guarantee! 29
Fixed Head Square Drives
Part No. Description Drive
29828 3/8" Square Drive 3/8"
29827 1/2" Square Drive 1/2"
Collet Keys For Adjustable Torque Wrench
Part No. Collet Nut Size Type Max. Torque*
04576 ER 11 Mini MIni 14 ft/lbs
04577 ER 16 Mini MIni 22 ft/lbs
04578 ER 20 Mini MIni 25 ft/lbs
04587 ER 25 Mini MIni 29 ft/lbs
04580-16 ER 16 Slotted Slotted 50 ft/lbs
04601-16 ER 16 Hex Hex 50 ft/lbs
04580-20 ER 20 Slotted Slotted 75 ft/lbs
04602-20 ER 20 Hex Hex 75 ft/lbs
04603-25 ER 25 Slotted Slotted 95 ft/lbs
04604-32 ER 32 Slotted Slotted 125 ft/lbs
04605-40 ER 40 Slotted Slotted 140 ft/lbs
03690-25 SYOZ 25/TG 100 Hook 100 ft/lbs
04018-TWA TG 75 Slotted Hook 100 ft/lbs
DNA16-TWA DNA 16 Slotted 50 ft/lbs
04588-R ER 32 Slotted Slotted 125 ft/lbs
SD-TWA SYOZ-20 Hook 45 ft/lbs
Adjustable Torque Wrench
Part No. Torque Range Length Weight Spigot
60 TH 5-45 ft/lbs 12" 1 lb. 16mm round
200 TH 30-150 ft/lbs 16.5" 1.75 lbs 16mm round
300 TH 45-228 ft/lbs 21.5" 2.5 lbs 16mm round
Retention Knob Sockets–Square Drive
Part No. Taper or Holder Flats Drive Max. Torque*
PSS - 30BT BT 30 Taper Retention Knob 0.535" 3/8" 40 ft/lbs
PSS - 30ISO ISO 30 Taper Retention Knob 0.535" 3/8" 40 ft/lbs
PSS - 40 All 40 Taper Retention Knobs 0.750" 3/8" 85 ft/lbs
PSS - 50 BT 50 Taper Retention Knob 1.187" 1/2" 110 ft/lbs
PSSC - 50 CAT 50 Taper Retention Knob 1.250" 1/2" 110 ft/lbs
*Recommended Torque is 80 – 90 % of max. value given.
Set adjustable dial to the correct amount of torque and tighten nut until wrench “clicks”.
• Get consistant cutting tool performance
• Ensure proper tightening for best T.I.R.
• Prevent tool accidents
ER 25 Castle DNA 16 Slotted
ER Slotted
TG Hook 04588-R
Hex
Retention Knob Sockets
Torque Wrenches and Adapters
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.30
• For HSK, ISO, BT, CAT spindles
• Change retention knobs from underneath
• Use with Digital Height Gauge to preset tools
Part No. Description
TSHG1-40-CT CAT 40 taper
TSHG1-30-41 BT 30 taper, 41mm flats
TSHG1-40-BT BT 40 taper
TSHG1-63F-36 HSK 63F, 36mm flats
TSHG1-63F-38 HSK 63F, 38mm flats
TSHG1-63F-46 HSK 63F, 46mm flats
TSHG1-30-36 ISO 30 taper, 36mm flats
TSHG1-30-38 ISO 30 taper, 38mm flats
TSHG1-30-47 ISO 30 taper, 47mm flats
TSHG1 Preset and Tightening Fixtures
• For HSK, ISO, BT, CAT spindles
• Change Retention Knobs from underneath
• Bolts right to workbench
Part No. Description
NTS-BT30-38 BT 30 taper - 38mm flats
NTS-BT30-41 BT 30 taper - 41mm flats
NTS-BT30-Slot BT 30 for tools with drive slots
NTS-ISO20-17 ISO 20 - 17mm flats
NTS-ISO20-22 ISO 20 - 22mm flats
NTS-ISO25-27 ISO 25 - 27mm flats
NTS-ISO30-36 ISO 30 - 36mm flats
NTS-ISO30-38 ISO 30 - 38mm flats
NTS-ISO30-47 ISO 30 - 47mm flats
NTS-HSK63A HSK63A - no flats
NTS-HSK63F-36 HSK 63F - 36mm flats
NTS-HSK63F-38 HSK 63F - 38mm flats
NTS-HSK63F-41 HSK 63F - 41mm flats
NTS-HSK63F-46 HSK 63F - 46mm flats
NTS-40 Taper Any CAT 40 or BT 40 taper
Tightening Fixtures
A large set-screw engages the drive slot in ISO, BT, and CAT tool holders to securely hold the tool in the fixture.
Side Mount Tightening Fixture
Attach tightening fixture to workbench or tool cart using bolts or screws. Allows easy access to reten-tion knobs from underneath. Tool flats are positively engaged by locking collar to secure tool holder. Heavy-duty plate steel construction for maximum rigidity and durability. Torque nuts and retention knobs to proper tightness using a torque wrench for best performance.
A sliding collar engages the wrench flats on HSK tool holders to allow tight-ening of collet nut.
All Techniks products are backed by our 100% satisfaction guarantee! 31
• 0 – 12" range
• Repeatability 0.0008"
• Automatic inch to metric conversion
OperationSet the height of your tool with the digital height gauge, then torque the nut to the proper tightness. Refer to the Torque Chart on back cover.
Part No. Description
54-212-012 12” Digital Height Gauge
12" inch height measured from gauge line (end of spindle).
Digital Height Gauge, Analog Axial Preset Gauge
This precision instrument is sealed against dust, grime, and oil, is shock and magnetism resistant, and is covered by a five year warranty.
Operation1. Use the gauge pin included to press down on the spring-loaded center piece as illustrat-
ed. Please be sure the gauge pin is placed on the shiny surface.
2. Turn the indicator to read “0”, then remove the gauge pin.
3. Put the unit on the workpiece and carefully jog the tool down to make contact with the gauge face. When the gauge reads "0" the tool is 50mm (2") above the workpiece.
• Accuracy 0.0002"
• Easy to measure tool depth
• Height 50mm (2")
Part No. Description
17906-2 ZSI-50 Preset Gauge
Save valuable machine time by using axial preset gauges to quickly set tool depth and increase accuracy.
Analog Axial Preset Gauge
Digital Height Gauge
Use with TSHG1 Tightening Fixture to set tool height. Reduce machine down-time and increase productivity by presetting tools.
32
Unleash the Full Potential of Your CNC Router!
3 inline outputsfor boring
lock recess
underside
moulder
chainsaw
With Techniks Aggregate Heads
Aggregate Head Advantages
• Increase productivity and profitability• Combine boring, mortising, routing, shaping,
and sawing operations • Eliminate tool changes, increase your tool
handling capacity
45˚ fixed angle
Floating Aggregate with Chip Guide System
IWF 2008 Challengers Award Finalist
See Our Modular Output System Page 40
Rotation Aggregate can be rotated 360˚
Spindle Outputs* M5, R6, S1, S2, Modular
• Interchangeable outputs increase flexibility.• Look for “Modular” in the specifications tables
Call us toll-free at: (800) 597-3921 to speak to an aggregate head applications specialist.
All Techniks products are backed by our 100% satisfaction guarantee! 33
Our Aggregates Offer Unmatched Quality & Reliability
Ultra Line Aggregates are lubricated in an oil bath and sealed from contaminants for extended life and use under heavy duty conditions. We recommend the Ultra Line for sawing using blades larger than 7", V-grooving, heavy routing applications, cutting MDF, composite materials, or cutting aluminum.
Function Line Aggregates are grease lubricated for standard duty operation. They provide the greatest number of configurations and application specific options to increase router productivity.
Smart Line Aggregates for light weight routers are smaller size aggregates for standard duty operations. They are grease lubricated and provide aggregate head productivity for owners of smaller CNC routers. See page 39.
How To Order AggregatesWe offer hundreds of different aggregate configura-tions, and can make practically any application specific aggregates you need. We can only show a few of the most popular models in this catalog. Please specify your application and center spindle type (ISO, HSK, BT, etc.) when ordering so we can make sure you get the right aggregate for your shop.
Call us at (800) 597-3921 to discuss your application requirements.
Only the very best components available are used to create our aggregate heads. This is why our aggregate heads run cool, quiet, and trouble-free. Every aggregate head we make is individually hand assem-bled by one, highly skilled technician, who is personally responsible for the quality of that aggregate, and signs their name to the aggregate upon completion. Our assembly process is a labor of love, but the end result is well worth the effort.
We promise • unmatched reliability • unmatched performance • unmatched support
How you benefit • increase productivity • increased reliability • reduced machine down-time
About our Aggregates
34
Ultra Line Mono Dimensions (mm)
Mono output aggregates are an affordable way to add 4th axis capability to your CNC router. Perform rout-ing, boring, mortising, and sawing operations faster to increase profits. Choose from a wide variety of spindle optputs. See chart below for supported outputs.
Ultra Line Mono (oil bath lubricated)Spindle Speed Max. 10,000 RPM
Tool Speed Max. 15,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.48
Gear Reduction* 1:0.676 (*optional feature)
Maximum Torque 17 ft. lbs
Spindle Direction Same as machine spindle
Maximum Temp. 185˚F
Spindle Outputs* M5, R6, S1, S2, P1, P2, P3, P4, 05
Function Line Mono Dimensions (mm)
Function Line Mono (grease lubricated)Spindle Speed Max. 10,000 RPM
Tool Speed Max. 15,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.48
Maximum Torque 15 ft. lbs
Spindle Direction Same as machine spindle
Maximum Temp. 185˚F
Spindle Outputs* M5, R6, S1, S2, Modular
Mono Aggregate Heads (1-spindle output)
HSK center spindle shown. Please specify your machine spindle and application.
*See page 40 for spindle output specifications.
Aggregate heads are confi gured to fi t your spindle. Please call us at (800) 597-3921 for ordering assistance.
35
Duo Aggregate Heads (2-spindle outputs)
Use Duo aggregates for faster manufacturing when more than one tool is required. Choose from a wide variety of spindle optputs. See chart below for supported outputs. Possibilities include routing, boring, mortising, and sawing operations. ER 25 or ER 32.
Function Line Duo Dimensions (mm)
Ultra Line Duo Dimensions (mm)
Function Line Duo (grease lubricated)Spindle Speed Max. 10,000 RPM
Tool Speed Max. 15,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.48
Maximum Torque 15 ft. lbs
Spindle Direction #1 clockwise, #2 opposite
Maximum Temp. 185˚F
Spindle Outputs* M5, R6, S1, S2, Modular
Ultra Line Duo (oil bath lubricated)Spindle Speed Max. 10,000 RPM
Tool Speed Max. 15,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.48
Gear Reduction* 1:0.676 (*optional feature)
Maximum Torque 17 ft. lbs
Spindle Direction #1 clockwise, #2 opposite
Maximum Temp. 185˚F
Spindle Outputs* M5, R6, S1, S2, P1, P2, P3, P4, 05
HSK center spindle shown. Please specify your machine spindle and application.
*See page 40 for spindle output specifications.
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
36
Quattro Aggregate Heads (4-spindle outputs)
Function Line Quattro Dimensions (mm)
Function Line Quattro (grease lubricated)Spindle Speed Max. 10,000 RPM
Tool Speed Max. 15,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.48
Maximum Torque 15 ft. lbs
Maximum Temp. 185˚F
Spindle Outputs* M5, R6, Modular
Quattro aggregate heads provide 4 tool spindles for more flexibility to combine operations. Choose from a wide variety of spindle optputs. See chart below for sup-ported outputs, and page 40 for output specifications.
• Add 4th axis capability to your CNC
• Reduce the number of tool changes needed
• Features 2, ER 25 spindles for boring, and 2 ER 32 spindles for custom applications
*See page 40 for spindle output specifications.
HSK center spindle shown. Please specify your machine spindle and application.
Aggregate heads are confi gured to fi t your spindle. Please call us at (800) 597-3921 for ordering assistance.
37
Vario Aggregate Heads (variable-angle)
Function Line Vario (grease lubricated)Spindle Speed Max. 15,000 RPM
Tool Speed Max. 15,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1
Swiveling Range 0° to 100°
Maximum Torque 15 ft. lbs
Spindle Direction Opposite machine spindle
Maximum Temp. 185˚F
Spindle Outputs* K1, K2
Function Line Vario Dimensions (mm)
Ultra Line Vario (oil bath lubricated)Spindle Speed Max. 13,760 RPM
Tool Speed Max. 15,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.09
Swiveling Range -100˚ to 100˚
Maximum Torque 17 ft. lbs
Spindle Direction Opposite machine spindle
Maximum Temp. 185˚F
Spindle Outputs* K1, K2
*See page 40 for spindle output specifications.
Ultra Line Vario Dimensions (mm)
The Vario can operate at any angle within it's range to perform “impossible” cuts, …right on your CNC. Function Line Vario aggregate operates at any angle from 0˚ to 100˚. (100˚ adjustable)Ultra Line Vario aggregate operates at any angle from -100˚ to 100˚. (200˚ adjustable)
HSK center spindle shown. Please specify your machine spindle and application.
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
38
12 g5
6045.5
5
34
141.
5 +
10
185
-10
40
35
140
Function Line Soft Touch ( (grease lubricated)Spindle Speed Max.* 18,000 RPM / 24,000 RPM
Floating Range 10 mm (with 10 mm adjustment)
Floating Pressure adjustable from 1/4 lb. to 20 lbs
Rotation aggregate can be rotated 360˚
Gear Ratio 1:1
Floating Bell** 70 mm deep X 105 mm I.D.
Maximum Torque 20 ft. lbs
Rotation Direction same as machine spindle
Maximum Temp. 185˚F
Spindle Outputs*** M5, R6, R7, P1, Modular
*24,000 RPM for high speed and/or small cutting tools.**Other bell diameters, lengths, and types available.***Also ER 40, saw blade, and shrink-fit available.See page 40 for spindle output specifications.
Function Line Soft-Touch Dimensions (mm)
Soft-Touch Floating Aggregate & Chip Guide System
The Soft-Touch aggregate head accurately follows the contours of your stock, automatically com-pensating for up to 10mm of variance. Floating pressure is adjustable from 1/4 lb. to 20 lbs. Convenient tool pre-setting flange allows you to perform fast, accurate adjustments. Compressed air connection on the aggre-gate provides saw dust evacuation.Aggregate comes with standard floating bell, ER 25 or ER 32 output (your choice) and wrench. Options include a variety of floating bells, shoes, and sleighs that are all interchangeable.
HSK center spindle shown. Please specify your machine spindle and application.
Chip Guide System features a rotor mounted at the tool, which directs chips into the machine’s dust exhaust system. Chips don't contami-nate your material so cutting quality remains high.
See a video of the Chip Guide in action at www.techniksusa.com/aggregate/cg
Aggregate heads are confi gured to fi t your spindle. Please call us at (800) 597-3921 for ordering assistance.
Floating Aggregate with Chip Guide IWF 2008 Challengers Award Finalist
39
Smart Line Aggregates for Lighter Weight Routers
Smart Line Vario (grease lubricated)Spindle Speed Max. 12,000 RPM
Tool Speed Max. 12,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1
Swiveling Range 0° to 100°
Maximum Torque 15 ft. lbs
Spindle Direction Same as machine spindle
Maximum Temp. 185˚F
Spindle Outputs* K1, K2
Smart Line Duo (grease lubricated)Spindle Speed Max. 8,000 RPM
Tool Speed Max. 12,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.5
Maximum Torque 15 ft. lbs
Spindle Direction one tool spindle same as machine spindle, one opposite
Maximum Temp. 185˚F
Spindle Outputs* M5, S1
Smart Line Lock Recess (grease lubricated)Spindle Speed Max. 8,000 RPM
Tool Speed Max. 12,000 RPM
Rotation Aggregate can be rotated 360˚
Gear Ratio 1:1.5
Maximum Torque 4 ft. lbs
Spindle Direction Same as machine spindle
Maximum Temp. 185˚F
Spindle Outputs* M5
Smart Line aggregates are individually hand-built just like our other aggregate lines. They offer full aggregate functionality for standard duty operations in a compact design for smaller routers. Smart Line aggregates are grease lubricated and offer an excellent price-to-performance ratio.
Smart Line Vario Adjustable Angle Type All the features of the Function Line Vario, but sized for lighter-duty applications. Comes with collet nut and wrench.
Smart Line Duo 2 spindle output aggregate.Dual spindle outputs are great for boring and sawing applications.
Smart Line Lockset RecessSpecially built for cutting lockset recesses. Comes with collet nut and wrench.
See page 40 for spindle output specifications.
See page 40 for spindle output specifications.See page 40 for spindle output specifications.
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
40
Modular System – Spindle Output Options
Note: Spindle outputs are designed to hold specific tools to perform a variety of tasks. Some spindle outputs cannot be used with certain aggre-gates. Please contact us for help selecting your outputs. Call us toll-free (800) 597-3921 or local (317) 803-8000.
Modular spindle outputs (highlighted in blue boxes) are all interchange-able on the aggregates that support the modular spindle output system.
W3 WeldonDIN 1835 B ∅10H6
W4 WeldonDIN 1835 B ∅12H6
M5 Modular ER 25
R6 Modular ER 32 R7 Modular ER 40
09 Modular Arbor
07 Modular Arbor
08 Modular Arbor
R3 ER 16 collet and nutRange: 0.5mm – 10mm
M5 ER 25 collet and nutRange: 1mm – 16mm
R6 ER 32 collet and nutRange: 3mm – 20mm
R7 ER 40 - for Soft-TouchRange: 4mm – 26mm
K1 ER 25 collet and nut
K2 Combi spindle, 45mm and52mm bolt circle
S1 Modular Saw Spindle
P1 Modular Saw ArborRange: 1.5mm-4mm tool shank
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
All Techniks products are backed by our 100% satisfaction guarantee! 41
Spindle Output Options
01 Saw Spindle
03 Special spindle ∅20h52x ∅6H7, 2x M6 - bolt circle 32mm
M10 centrical
05 Special spindle ∅20h62x ∅5H7, 2x M5 - bolt circle 32mm
M10 centrical
10 Special spindle ∅302x ∅6H7, 2x M5 - bolt circle 42mm
M10 centrical
12 Special spindle ∅30h52x M5 - bolt circle 45mm; ∅6H7, bolt circle 42mm
M10 centrical
13 Special spindle ∅30h52x M5 - bolt circle 45mm; ∅6H7, bolt circle 42mm M10 centrical
S1 Saw Spindle, 45mm bolt circle
S2 Saw Spindle, 52mm bolt circle
P1 Prolock spindle Range: 1.5mm-4mm tool shank
P2 Prolock spindleRange: mm – 52mm
P3 Prolock spindleRange: 98mm – 102mm
P4 Prolock spindleRange: 28mm – 32mm
P5 Prolock spindleRange: 28mm – 32mm
P6 Prolock spindleRange: 28mm
– 32mm
UHM12030Spindle for moulder head
I3 ER 16 collet insideRange: 1mm – 10mm
I5 ER 25 collet insideRange: 1mm – 16mm
N1 Notch whistleDIN 1835 E ∅6H5
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.42
Tool Holder Measuring Guide – Special Orders
Use this guide to help measure your tools to determine what you need to order, or for special order toolholders built to your specifications.
Make and model of CNC router ______________________________________
Pull Stud Dimensions
P = ____________
A = ____________
L = ____________
R = ____________
Toolholder Dimensions
D = ____________
F = ____________
W = ____________
A = ____________
N = ____________
Make and model of HSK spindle CNC Router ______________________________________________
Toolholder Dimensions
D = ____________
F = ____________
W = ____________
A = ____________
N = ____________
All Techniks products are backed by our 100% satisfaction guarantee! 43
Woodworking Collets Measuring Guide
ER Collet Style
SYOZ Collet Style
TG Collet Style
Use the guide below for selecting your replacement collets. The best way to tell what type of collet you need is to measure the length of the collet using a digital caliper. ER, TG, and SYOZ collets all have unique length and diameter measurements.
ER Collet Style Length O.D. (diameter)
ER 11 18mm (0.708") 11.5mm (0.45")
ER 16 27.5mm (1.08") 17mm (0.67")
ER 20 31.5mm (1.24") 21mm (0.83")
ER 25 34mm (1.34") 26mm (1.02")
ER 32 40mm (1.57") 33mm (1.3")
ER 40 46mm (1.81") 41mm (1.61")
ER 50 60 mm (2.36") 52mm (2.05")
DIN 6388 Collet Style Length O.D. (diameter)
EOC 8 26mm (1.026") 14.4mm (0.567")
SYOZ 20 34mm (1.34") 20mm (0.78")
RDO 20 34mm (1.34") 20mm (0.78")
407E 34mm (1.34") 20mm (0.78")
EOC 12 34mm (1.34") 20mm (0.78")
SYOZ 25 52mm (2.06") 35mm (1.38")
RDO 35 52mm (2.06") 35mm (1.38")
462E 52mm (2.06") 35mm (1.38")
EOC 32 60mm (2.36") 43.7mm (1.72")
TG Collet Style Length O.D. (diameter)
TG 75 47mm (1.85") 27mm (1.06")
TG 100 60mm (2.36") 35mm (1.38")
Special Order Collets Dimensions
Length __________ Diameter ___________ Other Markings __________
Length __________ Diameter ___________ Other Markings __________
Length __________ Diameter ___________ Other Markings __________
Standard Collet Dimensions
Stud Machine d1 d2 I1 I2 θ T
Special Pull Studs
We can get the pull studs you need. Just fill in your pull stud(s) dimensions on the chart below before you call. Keep your information in this catalog for easy re-orders.Please carefully select the pull stud you need by referring to the diagram.For safe operation please make sure that the pull stud you order is the exact pull stud your machine uses. Improper choice of pull stud can cause damage to the spindle and/or toolholder, and is a potential safety hazard.
T
d3D
d2
d1
l2l1
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.44
00100 1100151 1100152 1100153 1100156 1100157 1100158 1100159 1100160 1100165 1100166 1100167 1100168 1100170 1100300 1100316-SLN-L 900316-SLN-R 903508 2303508-1/4 2303508-1/8 2303508-3/16 2303508-5/16 2303520 2303520-1/2 2303520-1/4 2303520-1/8 2303520-10 2303520-3/16 2303520-3/8 2303520-5/16 2303520-7/16 2303531-1/2 2303531-1/4 2303531-1/8 2303531-10 2303531-16 2303531-3/16 2303531-3/8 2303531-5/16 2303531-5/8 2303531-7/16 2303531-9/16 2303636 2303638 2303690-25 2903691 2803868-1 2303868-1/2 2303868-1/4 2303868-1/8 2303868-10 2303868-16 2303868-20 2303868-25 2303868-3/16 2303868-3/4 2303868-3/8 2303868-5/16 2303868-5/8 2303868-7/16 2303868-7/8 2303868-9/16 2304008 - 1/2 2004008 - 1/4 20
04008 - 1/8 2004008 - 11/16 2004008 - 11/32 2004008 - 13/32 2004008 - 15/32 2004008 - 17/32 2004008 - 19/32 2004008 - 21/32 2004008 - 23/32 2004008 - 3/16 2004008 - 3/32 2004008 - 3/4 2004008 - 3/8 2004008 - 5/16 2004008 - 5/32 2004008 - 5/8 2004008 - 7/16 2004008 - 7/32 2004008 - 9/16 2004008 - 9/32 2004010 - 1 2004010 - 1/2 2004010 - 1/4 2004010 - 1/8 2004010 - 11/16 2004010 - 11/32 2004010 - 13/16 2004010 - 13/32 2004010 - 15/16 2004010 - 15/32 2004010 - 17/32 2004010 - 19/32 2004010 - 21/32 2004010 - 23/32 2004010 - 25/32 2004010 - 27/32 2004010 - 29/32 2004010 - 3/16 2004010 - 3/32 2004010 - 3/4 2004010 - 3/8 2004010 - 31/32 2004010 - 5/16 2004010 - 5/32 2004010 - 5/8 2004010 - 7/16 2004010 - 7/32 2004010 - 7/8 2004010 - 9/16 2004010 - 9/32 2004018 2804018-TWA 2904208 - 01.0 1504208 - 01.5 1504208 - 02.0 1504208 - 02.5 1504208 - 03.0 1504208 - 03.5 1504208 - 04.0 1504208 - 04.5 1504208 - 05.0 1504211 - 01.0 1504211 - 01.5 1504211 - 02.0 15
04211 - 02.5 1504211 - 03.0 1504211 - 03.5 1504211 - 04.0 1504211 - 04.5 1504211 - 05.0 1504211 - 05.5 1504211 - 06.0 1504211 - 06.5 1504211 - 07.0 1504211 - 1/16 1404211 - 1/4 1404211 - 1/8 1404211 - 3/16 1404211 - 3/32 1404211 - 5/32 1404211 - 7/32 1404216 - 01 1504216 - 02 1504216 - 03 1504216 - 04 1504216 - 05 1504216 - 06 1504216 - 07 1504216 - 08 1504216 - 09 1504216 - 1/16 1404216 - 1/4 1404216 - 1/8 1404216 - 10 1504216 - 11/32 1404216 - 13/32 1404216 - 3/16 1404216 - 3/32 1404216 - 3/8 1404216 - 5/16 1404216 - 5/32 1404216 - 7/32 1404216 - 9/32 1404220 - 02 1504220 - 03 1504220 - 04 1504220 - 05 1504220 - 06 1504220 - 07 1504220 - 08 1504220 - 09 1504220 - 1/2 1404220 - 1/4 1404220 - 1/8 1404220 - 10 1504220 - 11 1504220 - 11/32 1404220 - 12 1504220 - 13 1504220 - 13/32 1404220 - 15/32 1404220 - 3/16 1404220 - 3/32 1404220 - 3/8 1404220 - 5/16 1404220 - 5/32 1404220 - 7/16 1404220 - 7/32 14
Part No. Pg. Part No. Pg. Part No. Pg.
Part Number Index: 00100 – 04220-7/32
All Techniks products are backed by our 100% satisfaction guarantee! 45
04220 - 9/32 1404225 - 02 1504225 - 03 1504225 - 04 1504225 - 05 1504225 - 06 1504225 - 07 1504225 - 08 1504225 - 09 1504225 - 1/2 1404225 - 1/4 1404225 - 1/8 1404225 - 10 1504225 - 11 1504225 - 11/32 1404225 - 12 1504225 - 13 1504225 - 13/32 1404225 - 14 1504225 - 15 1504225 - 15/32 1404225 - 16 1504225 - 17/32 1404225 - 19/32 1404225 - 3/16 1404225 - 3/32 1404225 - 3/8 1404225 - 5/16 1404225 - 5/32 1404225 - 5/8 1404225 - 7/16 1404225 - 7/32 1404225 - 9/16 1404225 - 9/32 1404232 - 03 1504232 - 04 1504232 - 05 1504232 - 06 1504232 - 07 1504232 - 08 1504232 - 09 1504232 - 1/2 1404232 - 1/4 1404232 - 1/8 1404232 - 10 1504232 - 11 1504232 - 11/16 1404232 - 11/32 1404232 - 12 1504232 - 13 1504232 - 13/32 1404232 - 14 1504232 - 15 1504232 - 15/32 1404232 - 16 1504232 - 17 1504232 - 17/32 1404232 - 18 1504232 - 19 1504232 - 19/32 1404232 - 20 1504232 - 21/32 1404232 - 23/32 1404232 - 3/16 14
04232 - 3/32 1404232 - 3/4 1404232 - 3/8 1404232 - 5/16 1404232 - 5/32 1404232 - 5/8 1404232 - 7/16 1404232 - 9/16 1404232 - 9/32 1404232 -7/32 1404240 - 04 1504240 - 05 1504240 - 06 1504240 - 07 1504240 - 08 1504240 - 09 1504240 - 1 1404240 - 1/2 1404240 - 1/4 1404240 - 1/8 1404240 - 10 1504240 - 11 1504240 - 11/16 1404240 - 11/32 1404240 - 12 1504240 - 13 1504240 - 13/32 1404240 - 14 1504240 - 15 1504240 - 15/32 1404240 - 16 1504240 - 17 1504240 - 17/32 1404240 - 18 1504240 - 19 1504240 - 19/32 1404240 - 20 1504240 - 21 1504240 - 21/32 1404240 - 22 1504240 - 23 1504240 - 23/32 1404240 - 24 1504240 - 25 1504240 - 26 1504240 - 3/16 1404240 - 3/4 1404240 - 3/8 1404240 - 5/16 1404240 - 5/32 1404240 - 5/8 1404240 - 7/16 1404240 - 7/32 1404240 - 7/8 1404240 - 9/16 1404240 - 9/32 1404576 2904577 2904578 2904580-16 2904580-20 2904587 2904588-R 2904601-16 29
04602-20 2904603-25 2904604-32 2904605-40 2904608 2804609 2804610 2804613 2804614 2804615 2804616 2804617 2804618 2804620 2804621 2804622 2804623 2804624 2804888 704889 704891 704893 704894 704895 704896 704897 704898 705.024.001 1305.024.002 1305.024.003 1305.024.004 1305.024.005 1305.024.006 1305.024.012 1305.024.013 1305.024.014 1305.024.015 1305.024.016 1305.024.018 1305.024.020 1305.024.114 1305.024.116 1305.024.118 1305.024.120 1305.024.122 1305.024.126 1305.024.130 1305.024.131 1305.024.132 1305.024.133 1305.024.134 1305.024.135 1305.024.136 1305.024.137 1306000-2016M 506000-2016MC 506000-2516 506000-2520 506001 706001-W 706010 706101 606101-SLOTNUT 606102 6
Part No. Pg. Part No. Pg. Part No. Pg.
Part Number Index: 04220-9/32 – 06102
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.46
06102-C 606102-DNA 606102-SLOTNUT 606103 606103-SLOTNUT 606104 606104-SLOTNUT 606105 606105-SLOTNUT 606106 606106-SLOTNUT 606107 606107-SLOTNUT 606108-2.5 606108-2.5-SLOTNUT 606109 606110 606111 606111-90 606112 706113 706113-W-60 706113-W-60-A 706113-W-90 706114 706115 7061-BT35-ER 32 76 7061-BT35-ER 32 76A 707710 2707711 07801 2507803 2507806 2507808 2507812 2507814 2508516 - 03.5 2608516 - 04.0 2608516 - 04.5 2608516 - 05.0 2608516 - 05.5 2608516 - 06.0 2608516 - 06.5 2608516 - 07.0 2608516 - 07.5 2608516 - 08.0 2608516 - 08.5 2608516 - 09.0 2608516 - 09.5 2608516 - 10.0 2608520 - 03.5 2608520 - 04.0 2608520 - 04.5 2608520 - 05.0 2608520 - 05.5 2608520 - 06.0 2608520 - 06.5 2608520 - 07.0 2608520 - 07.5 2608520 - 08.0 2608520 - 08.5 2608520 - 09.0 2608520 - 09.5 2608520 - 10.0 26
08520 - 10.5 2608520 - 11.0 2608520 - 11.5 2608520 - 12.0 2608520 - 12.5 2608520 - 13.0 2608525 - 03.5 2608525 - 04.0 2608525 - 04.5 2608525 - 05.0 2608525 - 05.5 2608525 - 06.0 2608525 - 06.5 2608525 - 07.0 2608525 - 07.5 2608525 - 08.0 2608525 - 08.5 2608525 - 09.0 2608525 - 09.5 2608525 - 10.0 2608525 - 10.5 2608525 - 11.0 2608525 - 11.5 2608525 - 12.0 2608525 - 12.5 2608525 - 13.0 2608525 - 13.5 2608525 - 14.0 2608525 - 14.5 2608525 - 15.0 2608525 - 15.5 2608525 - 16.0 2608532 - 03.5 2608532 - 04.0 2608532 - 04.5 2608532 - 05.0 2608532 - 05.5 2608532 - 06.0 2608532 - 06.5 2608532 - 07.0 2608532 - 07.5 2608532 - 08.0 2608532 - 08.5 2608532 - 09.0 2608532 - 09.5 2608532 - 10.0 2608532 - 10.5 2608532 - 11.0 2608532 - 11.5 2608532 - 12.0 2608532 - 12.5 2608532 - 13.0 2608532 - 13.5 2608532 - 14.0 2608532 - 14.5 2608532 - 15.0 2608532 - 15.5 2608532 - 16.0 2608532 - 16.5 2608532 - 17.0 2608532 - 17.5 2608532 - 18.0 2608532 - 18.5 2608532 - 19.0 26
08532 - 19.5 2608532 - 20.0 2608540 - 04.0 2608540 - 04.5 2608540 - 05.0 2608540 - 05.5 2608540 - 06.0 2608540 - 06.5 2608540 - 07.0 2608540 - 07.5 2608540 - 08.0 2608540 - 08.5 2608540 - 09.0 2608540 - 09.5 2608540 - 10.0 2608540 - 10.5 2608540 - 11.0 2608540 - 11.5 2608540 - 12.0 2608540 - 12.5 2608540 - 13.0 2608540 - 13.5 2608540 - 14.0 2608540 - 14.5 2608540 - 15.0 2608540 - 15.5 2608540 - 16.0 2608540 - 16.5 2608540 - 17.0 2608540 - 17.5 2608540 - 18.0 2608540 - 18.5 2608540 - 19.0 2608540 - 19.5 2608540 - 20.0 2608540 - 20.5 2608540 - 21.0 2608540 - 21.5 2608540 - 22.0 2608540 - 22.5 2608540 - 23.0 2608540 - 23.5 2608540 - 24.0 2608540 - 24.5 2608540 - 25.0 2608540 - 25.5 2608540- 03.5 261016.0030 241016.0040 241016.0050 241016.0060 241016.0080 241016.0100 241016.0120 241116.0014 241116.0018 241116.0038 241116.0125 241116.0150 241116.0175 241116.0200 241116.0225 241116.0250 241116.0300 24
Part No. Pg. Part No. Pg. Part No. Pg.
Part Number Index: 06102-C – 1116.0300
All Techniks products are backed by our 100% satisfaction guarantee! 47
1116.0316 241116.0350 241116.0400 241116.0450 241116.0500 241116.0600 241116.0700 241116.0800 241116.0900 241116.1000 2412000-CMS 512040-CMS 512213-W-50 512213-W-63 512213-W-90 512215-W-57 512261-W 512407-W 512700-100-W 812700-40-W 812700-55-W 812700-80-W 813001 2513001-45 2513003 2513003 25171.05.008.001 4171.05.008.002 4171.05.036.016 12171.05.036.018 12171.05.036.020 12171.05.036.035 12171.05.046.003 9171.05.071.010 10171.05.071.011 10171.05.071.250 10171.05.071.375 10171.05.071.500 10171.05.071.750 10171.05.072.1 1017706 2717707 2717708 2717906-2 31200 TH 292016-200 2421225 1821240 1821325 1921332 1921340 1922220 2827116 2427116-30 2427116-40 2427116-45 2427116-50 2427116-55 2427116-60 2427116-65 2427216 2427500 2128110 2128210 21
29132 1829827 2929828 29300 TH 2930000 430001 430002 430005 431025F 431374-60 433108 1833111 1833116 1833120 1833125 1833125-L 1839.05.046.001 941060 841080-3H 841085 841087 841616 1941620 1941625 1941632 1941640 194403502 2546111 1746116 1746120 1746125 1746132 1746140 1749019 2550001 454-212-012 3160 TH 2964.05 071.625 1064.05 071.750 1064.05.043.224 1264.05.043.225 1264.05.046.051 964.05.071.250 1064.05.071.375 1064.05.071.500 1067.05.046.001 9750-19 2584.05.008.001 484.05.008.002 484.05.008.003 485.05.008.002 486.05.008.002 486.05.008.003 4894-22 24CMS-RR32 9DC32-1/2 27DC32-1/4 27DC32-3/16 27DC32-3/4 27DC32-3/8 27DC32-5/16 27DC32-5/8 27DNA16-TWA 24DNA16-TWA 29
DNA16W 24NT-54300130 5NTS-40 Taper 30NTS-BT30-38 30NTS-BT30-41 30NTS-BT30-Slot 30NTS-HSK63A 30NTS-HSK63F-36 30NTS-HSK63F-38 30NTS-HSK63F-41 30NTS-HSK63F-46 30NTS-ISO20-17 30NTS-ISO20-22 30NTS-ISO25-27 30NTS-ISO30-36 30NTS-ISO30-38 30NTS-ISO30-47 30PSS - 30BT 29PSS - 30ISO 29PSS - 40 29PSS - 50 29PSSC - 50 29SD-20mm-.250 22SD-20mm-.312 22SD-20mm-.375 22SD-20mm-.500 22SD-20mm-.625 22SD-20mm-Nut 22SD-C001-.125 22SD-C001-.187 22SD-C001-.250 22SD-C001-.312 22SD-C001-.375 22SD-C001-.500 22SD-C001-Nut 22SD-C015-.125 22SD-C015-.250 22SD-C015-.312 22SD-C015-.375 22SD-C015-.500 22SD-C015-.625 22SD-C015-.750 22SD-C015-Nut 22SD-TWA 29SS-22-1/2 22SS-22-1/4 22SS-22-10 22SS-22-3/8 22SS-22-Ext -Nut 22SS-22-Nut 22TE-171.05.071.500-S 10TE-64.05 071.750-S 10TE-64.05.071.500-S 10TSHG1-30-36 30TSHG1-30-38 30TSHG1-30-41 30TSHG1-30-47 30TSHG1-40-BT 30TSHG1-40-CT 30TSHG1-63F-36 30TSHG1-63F-38 30TSHG1-63F-46 30
Part No. Pg. Part No. Pg. Part No. Pg.
Part Number Index: 1116.0316 – TSHG1-63F-46
Ph. (800) 597-3921 • Fax (877) 776-9994 E-mail: [email protected], website: www.techniksusa.com9930 East 56th St., Indianapolis, IN 46236Office Hours: Monday – Friday 8:00 am to 5:00 pm, EST.© June, 2008, Techniks Inc., Indianapolis, Indiana USA, LITCNC2008
Tools cut smoother, faster, & safer when you tighten collets, nuts, and retention knobs to correct specifications.
Use a tightening fixture and torque wrench to make sure tools are
properly tightened. Incorrect torque can cause cracked col-lets, poor cutting performance, and possibly cause tools to come loose during operation,
causing a very dangerous work environment.
Collet Nuts Wrench Type Max. Torque Rec. Torque* Wrench
ER 16 Slotted 50 ft/lbs 45 ft/lbs 41916
ER 16 Hex Hex 50 ft/lbs 45 ft/lbs 41116
ER 20 Slotted 75 ft/lbs 67 ft/lbs 41920
ER 20 Hex Hex 75 ft/lbs 67 ft/lbs 41120
ER 25 Spanner Slotted 95 ft/lbs 85 ft/lbs 41925
ER 25 M Castle 29 ft/lbs 25 ft/lbs 23125
ER 32 Spanner Slotted 125 ft/lbs 112 ft/lbs 41932
ER 40 Spanner Slotted 140 ft/lbs 126 ft/lbs 41940
SYOZ 25 Hook 100 ft/lbs 90 ft/lbs 03638
TG 75 Hook 100 ft/lbs 90 ft/lbs 27500
TG 100 Hook 100 ft/lbs 90 ft/lbs 28110
Retention Knobs Wrench Flats Drive Max. Torque Rec. Torque*
BT 30 Taper 0.535" 1/4" 40 ft/lbs 36 ft/lbs
ISO 30 Taper 0.535" 3/8" 40 ft/lbs 36 ft/lbs
Any 40 Taper 0.750" 3/8" 85 ft/lbs 76 ft/lbs
BT 50 Taper 1.187" 1/2" 110 ft/lbs 99 ft/lbs
CAT 50 Taper 1.250" 1/2" 110 ft/lbs 99 ft/lbs
Torque Chart
Recommended torque is 80-90% maximum torque value.
1. Snap collet into nut.
2. Insert cutter into collet
3. Hand tighten collet nut assembly into tool holder
4. Insert tool holder assembly into tightening fixture and secure it.
5. Tighten collet nut to recommended torque using a torque wrench.