cnc milling cutters · 2016. 6. 23. · with a high quality awareness. for example, many vhf single...
TRANSCRIPT
CNC Milling Cutters
> 25 years vhf
Update01/2015
EngravingUniversal gravers and engraver’s milling cutters as well as special tools for engraving acrylic glass, stainless steel and pressed paper sheets.
MillingTools from one to six cutting edges made of car-bide or diamond – uncoated or coated in more than 700 variants in total!
Deburring | chamfering | countersinkingRemoving burrs or chamfering edges with special tools from vhf. Countersinks for screws in wood, plastics, non-ferrous metals or steel.
PolishingOur special diamond polishing tools bring your milled edges or engravings in acrylic glass to a high gloss.
Thread cuttingCut your threads either with thread whirling cut-ters or with combined circular thread cutters which drill the tapping hole at the same time.
DrillingFine drills in 0.1 mm gradations with very good im-mersion characteristics for different kinds of materi-als.
CuttingKnifes and lances up to 70 mm length for straight cuts and diagonal cuts in all kinds of materials which can be better cut than milled.
vhf tools for...
You will find many more production samples at www.vhf.deAs of: January 2015 Pict
ure
cred
its: f
olie
ndes
ign
Gm
bH
, Ess
en (
4th fr
om to
p).
100 %
recy
cled
Welcome to vhf!
I want to thank you for your interest in our tools. With this issue, you have a much thicker catalogue in your hands than before. Compared with the previous issue more than 400 new tools have been added. That means an extension of our range of tools by more than 70 per cent.
Quite much has happened concerning the composite cutters – we have added more than 130 new tools in six categories. But also the selection of drills and diamond tools has become remarkably bigger. And we even have nearly doubled the quantity of single tooth cutters – a tool category which has already been well represented before. For reasons of clarity, we have marked all new tools with a red asterisk*. You will see that there are only very few pages without any asterisk in this new catalogue.
We were able to extend our range of tools in such a way especially because we have invest-ed heavily in our machinery and made our production more efficient during the past years. This leads also to the nice side benefit that we could reduce again many prices compared with the last issue of the catalogue.
Our friendly and competent vhf tool team would be glad to answer all your questions. Please do not hesitate to contact them.
Frank Benzinger Chief Executive Officer
Woodapprox. 95,000 kg
more than 3,000 trees for fresh fibre paper
Electricityapprox 50.000 kWh
consumption of a family of four in over 10 years
Waterapprox. 500,000 l
consumption for more than 3,000 full baths
Wasteapprox. 25,000 kg
amount of a family of four in over 10 years
By using 100 % recovered paper for the complete edition of these catalogues, the following resources have been saved:
Table of contentsGeneral informationDevelopment and production 6Special wishes? 7Order today, use it tomorrow... 7Comfortable search in the vhf Shop 8Tools live in the working process 8Why carbide tools? 9Why diamond tools? 10Hard coatings for carbide tools 11Overview of carbide and diamond tools 14
Single tooth cuttersVarius® cutters 22Cutters with polished flute 26Cutters with hawk beak profile 28Cutters with hawk beak and undercut 30Cutters with face radius 31Varius® cutters with left-hand twist 32Cutters, polished, with left-hand twist 33V-slot cutters for aluminium composites 34
Double tooth cuttersVarius® cutters 36Cutters with polished flute 37Cutters with fishtail 38HSC cutters 39Cutters for aluminium 40Cutters for aluminium profiles 41Cutters for stainless steel 42Cutters for wood 43Cutters with face radius 44Cutters with torus and undercut 45Cutters with face radius and undercut 46Rub out cutters 47
Triple tooth cuttersVarius® cutters 50Cutters for foam 51Cutters for stainless steel 52
Four tooth cuttersVarius® cutters 54Ratio cutters 55
Roughing and finishing cuttersRoughing cutters for copper 58Roughing cutters for graphite 59Finishing cutters for copper 60
Composite cuttersFinely toothed cutters 62Finely toothed cutters with chip breaker 63Medium toothed cutters 64Coarsely toothed cutters 65Straightly slotted honeycomb cutters 66Spiral-fluted honeycomb cutters 67PCB outline cutters, diamond-toothed 68PCB outline cutters, spiral-toothed 69
Engraving toolsGravers 72Box gravers 74Engraver’s milling cutters for acrylic 75Engraver’s milling cutters for stainless steel 76Channel cutters 77Isolation engraving tool 78Semi-finished gravers 79
For deburring, countersinking, cham-fering of non-ferrous metals and plas-tics. M Page 81
Using these tools you can cut threads in plastics, non-ferrous or ferrous met-als and composites. M Page 95
Lances and knives for the different cutting heads and the universal head. M Page 105
A selection of tools for typical gold-smith works in materials like wax, metal and plastics. M Page 117
Carbide milling cutters in more than 700 variants – for most tools also avail-able with coating. M Page 21
Carbide Tools | Diamond Tools4
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Table of contentsDeburring toolsDeburring tools 82Deburring tools, quadrant 83
Router bitsV slot cutters 86Long hole slot cutters 87Slot cutters 88Character cutter 89Radius cutters 90Chamfering cutters 91Cutters with quadrant 91V slot cutters for aluminium composites 93Triple tooth surface milling cutters 94
Thread cuttersThread whirling cutters 96Circular thread cutters 97
DrillsDrills with 3 mm shank 100Drills with 6 mm shank 102
Lances and knives Lances 106Knives 107
Diamond toolsPCD single tooth cutters 110PCD double tooth cutters 111MCD polishing cutters 112MCD polishing gravers 113PCD polishing cutters 114PCD polishing gravers 115CVD cutters 116
Impression toolsGoldsmith tools 118
AccessoriesVacuum fleece 120Special adhesive film 120Stop rings 120Reducing bushes 121Coolants and lubricants 121
AppendixTips for the proper use of tools 122Hints for the right number of teeth 122Setting the machining parameters 123Choice of the milling direction 123Cooling/lubrication 124What to do in case of problems? 124Order form 125Your contacts 126vhf machine catalogue 127
Massive steel body with integrated car-bide cutting edges; for wood, plastics and composite plates. M Page 81
For plastics, non-ferrous metals, PCBs or thermosetting plastics and thermo-plastics. M Page 99
A diamond instead of a carbide cutting edge improves the quality and endur-ance – without cooling. M Page 109
Stop rings and reducing bushes; vacu-um fleece and adhesive film; lubricants for cooling. Page 119
All prices exclude VAT, customs duties and transporta-tion/packaging fees • Deliveries are always subject to our Terms of Sale; we would be glad to send them to you on request and you will find them on the inter-net at download.vhf.de • All trade and product names mentioned in this catalogue belong to their owners • Technical modifications and errors excepted.
Engraver’s milling cutters and gravers for machining materials from plastics to stainless steel. M Page 71
Carbide Tools | Diamond Tools 5
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Development and production
Our tool experts develop sophisticated cutting edge geometries in order to ex-actly adjust the tools to different materials and machining strategies.
These standard and special tools will be manufactured on most modern six and seven axis precision grinding centres. vhf exclusively uses ultra finest grain or super finest grain carbides of German ori-gin. Finished tools will be checked by a CNC measuring machine with four axes and a resolution of the measured values of 0.25 µm. Thus highest quality is guaran-teed.
The own production facilities enable us to flexibly manufacture variants of ex-isting types. So the range of tools will be further extended also during the period of validity of this catalogue. Just check in our tool section on the internet (tools.vhf.de) the tool news from time to time.
Everything from a single source: Beginning with the development of the cutting edge geometry over the production of the carbide tools on a 6 or 7 axis grinding centre up to a contact-free complete measuring with a 4 axis machine.
All vhf tools are exclusively manufactured with certi-
fied green power of 100 % hydroelectricity.
A part of the vhf machinery for producing tools: 5 axis cylindrical grinding machine
(right), several six axis grinding machines for producing tools with diameters from
0.1 to 16 mm, in the background left a 4 axis measuring machine.
7 axis grinding machine with integrated robot loader for producing tools with diam-eters from 0.5 to 12 mm.
Carbide Tools | Diamond Tools6
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Result: detail view of the cutting edge geometry of a single tooth cutter manufactured from the carbide type DK460UF.
Micrograph of the carbide type DK460UF with 1,000 times magnification. With kind permission of Gühring KG.
It’s all the mix
Hardness, resistance to wear and ductility of the car-bide are significantly influenced by the combination of its ingredients and the grain size of the hard material. An increasing proportion of tungsten carbide leads to in-creased hardness and ductility and higher resistance to wear. Milling tools mostly have a tungsten carbide pro-portion of 90 %. Relevant grain sizes range from less than 0.2 microns (nano) to over 1.3 microns (fine/medium grains) – smaller grain sizes result in a greater hard-ness and bending strength. The material becomes more resistant to wear. If the proportion of the binder phase increases (especially cobalt of about 10 %), the bending strength, tensile strength and impact strength can be improved. The material becomes “tougher”.
Generally vhf uses different kinds of carbide substrates for their tools – always with the aim to create the best pos-sible tool with the most benefit for the user. When choosing our technology partners, we always put great emphasis on the fact that they are renowned companies with a high quality awareness.
For example, many vhf single tooth cutters are manufac-tured from the carbide type DK460UF, which consists of 90 % tungsten carbide and 10 % cobalt; the average tungsten carbide grain size in this case is 0.5 microns. Thus it offers a balanced mix of wear resistance and toughness.
Why carbide tools?Due to its extraordinary features, tools made of carbide metal are far superior to those made of high speed steel (HSS). For high speed cutting, HSS is not suitable any-more. All tools from vhf are carbide tools – either completely or partly. Most of the tools are solid carbide tools. The diamond tools consist of a carbide shank with an attached diamond and the router bits have carbide cutting edges.
Sintered from finest powders under high pressure
Carbide metal is a sintered material and consists main-ly of the hard material tungsten carbide (WC). For a targeted optimization small amounts of other carbide phases may additionally be used. Mainly these are tita-nium carbides (TiC), tantalum carbides (TaC), niobium carbides (NbC) or chromium carbides (CrC). The second main component is the binder phase which mainly con-sists of cobalt (Co) and may partly be complemented by nickel (Ni), iron (Fe) and nickel chromium (NiCr). This mixture of originally powdery ingredients will finally be sintered under high pressure and high temperatures un-til it becomes a solid object.
Carbide Tools | Diamond Tools 9
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Why diamond tools?Diamond is even much harder than carbide. The carbide tools with diamond attachment which are offered by vhf have a multiple of the endurance of carbide tools. We use three sorts of diamonds:
Our monocrystalline diamonds (MCD) consist of pure carbon and are extremely resistant to wear. Although they have been produced synthetically, they have the same characteristics as natural diamonds. This ultra-hard material ensures glassy polishing edges. MCD tools are excellent for polishing acrylic glass to a high gloss.
Polishing graver with monocrystalline diamond.
Single tooth cutter with polycrystalline diamond.
Double tooth cutter with two CVD thick layer plates.
Polycrystalline diamonds (PCD) will be sintered from numerous single crystals at high temperatures and pres-sures to a solid plate. This production process is compa-rable to that of carbide. Depending on the grade, they are suitable for milling and polishing tasks.
The PCD polishing plates have a very fine grain size and will be finished by grinding in a separate step after laser cutting respectively eroding. Thus, there are only slight differences in polishing quality compared with the results of MCD tools. However, in most cases they are more than compensated by the effect of the longer cutting edges.
CVD thick film plates are built up in thin layers by Chemical Vapour Deposition (CVD). Afterwards they are cut into shape by a laser beam. The result is a very homogeneous diamond structure and an extremely smooth and sharp cutting edge for highest surface quali-ties. Compared with the already very good results of PCD tools, the CVD tools distinguish themselves by an even greater hardness and resistance to wear which can lead to an even longer endurance. In contrast to PCD, CVD has no metallic binder phase, so the bending strength and the impact resistance are a bit lower. So, by its fea-tures, it can be regarded as an ideal completion to PCD and MCD.
Despite their higher cost price, diamond tools are the more economic alternative for many processing tasks – last but not least due to the possibility that they can be regrind for several times.
Carbide Tools | Diamond Tools10
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Hard coatings for carbide toolsNowadays, carbide milling tools are often additionally coated with hard material. By the proper choice of the coating, the tool endurance will be considerably extended. The range of possible coating alternatives is wide:
This coating has been especially de-signed for high performance milling of aluminium (alloys). Due to its low affinity to aluminium AluSpeed® effec-tively prevents the formation of built-up edges. Extremely smooth surfaces re-duce the friction at the cutting face and facilitate the chip flow. Due to its great hardness also an excellent protection against wear is ensured.
CC AluSpeed®
Type PVD coatingMaterial TiB2
Micro hardness 4,000 VHN0.05
Coating thickness 2.0 µm ± 0.7Frictional value* –Max. application temperature
900 °C
Coating colour silver greyvhf tools ■ single tooth cutters with hawkbeak
■ double tooth cutters for aluminium
* dry against steel
HARDLOX®
Type PVD coatingMaterial TiAlN/TiSiNMicro hardness 3,800 VHN0.05
Coating thickness 3.0 µm ± 1.0Frictional value* 0.30Max. application temperature
1,100 °C
Coating colour copperyvhf tools ■ triple tooth cutters for stainl. steel
* dry against steel
An extremely hard and smooth, drop-let-free coating due to its silicon dop-ing. With best adhesive properties thanks to the new HiPIMS (High Power Impulse Magnetron Sputtering) tech-nology. HARDLOX® is the first choice for machining stainless steel, materials which are difficult to machine such as titanium or chromium-cobalt-molybde-num alloys and hard machining up to 70 HRC.
HPN1
Type PVD coatingMaterial AlTiCrNMicro hardness 3,500 VHN0.05
Coating thickness 3.0 µm ± 1.0Frictional value* 0.30Max. application temperature
1,100 °C
Coating colour greyvhf tools ■ four tooth ratio cutters
* dry against steel
The HPN1 coating is also produced with the ultra-modern HiPIMS meth-od. Thereby it is effectively fixed in the substrate. This facilitates a high hard-ness and exceptional toughness. The strengths of HPN1 lie in machining steel, cast iron, titanium and materials with hardness up to 55 – 60 HRC which are difficult to machine.
Carbide Tools | Diamond Tools 11
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
TINALOX® SN2
Type PVD coatingMaterial TiAlNMicro hardness 3,500 VHN0.05
Coating thickness 3.0 µm ± 1.0 (1.5 µm ± 0.5)Frictional value* 0.30Max. application temperature
1,000 °C
Coating colour black anthracitevhf tools ■ engraver's milling cutters and dou-
ble tooth cutters for stainless steel ■ double, triple and four tooth cut-
ters Varius® ■ deburring tools ■ thread whirling cutters
* dry against steel
TINALOX® SN2 is a proven all-round coating for all types of steel and cast iron up to 50 HRC. It has a wide appli-cation field for roughing and finishing tasks. Tools which are coating with this contour-close thin film are also per-fectly suitable for engraving and/or for fine works in stainless steel.
SHC®
Type DLC coatingMaterial ta-CMicro hardness > 4,000 VHN0.02
Coating thickness 2.0 µm ± 0.2Frictional value* 0.10Max. application temperature
400 °C
Coating colour blackvhf tools ■ single tooth cutters Varius®
■ V-slot cutters for aluminium com-posites
■ double tooth cutters for wood ■ roughing cutters for graphite
* dry against steel
This super hard carbon coating with tightest coating thickness tolerance is the first choice for all tasks that require an outstanding dry running. Due to its high hardness SHC® resists strong abrasive exposures, e. g. when machin-ing CRP and GRP. Also ideal for machin-ing solid wood and (wood-metal) lami-nates. It can be used as inexpensive alternative to diamond coatings at anytime.
HYPERLOX®
Type PVD coatingMaterial AlTiNMicro hardness 3,700 VHN0.05
Coating thickness 3.0 µm ± 1.0Frictional value* 0.30Max. application temperature
1,100 °C
Coating colour black anthracitevhf tools ■ four tooth cutters Varius®
* dry against steel
HYPERLOX® is characterized by being almost free from internal stress, having a high oxidation resistance and an ad-ditional extra of hardness. Due to the very wide range of applications (in al-loyed and stainless steel, cast iron and materials with up to 60 HRC which are difficult to machine), this layer is an all-round coating which shows its strengths especially in roughing.
Carbide Tools | Diamond Tools12
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
MicroSpeed
Type CVD coatingMaterial diamondMicro hardness > 10,000 VHN0.05
Coating thickness 9.0 µm + 3.0Frictional value* –Max. application temperature
700 °C
Coating colour dark greyvhf tools ■ diamond-toothed PCB outline
cutters ■ spiral-toothed PCB outline cutters
Please note: Diamond is an insulator, i. e. there is no measur-ing by means of electric contact possible.* dry against steel
A multilayer coating with the best possible cost-performance ratio. It is optimised for nearly all tasks in the field of printed circuit board manufactur-ing. You get a considerably higher per-formance in machining FR4/FR5, halo-gen-free materials and laminates with and without ceramic fillers.
CCDia® FiberSpeed
Type CVD coatingMaterial diamondMicro hardness > 10,000 VHN0.05
Coating thickness 9.0 µm ± 1.0Frictional value* –Max. application temperature
700 °C
Coating colour dark greyvhf tools ■ finely toothed composite cutters
with chip breaker
Please note: Diamond is an insulator, i. e. there is no measur-ing by means of electric contact possible.* dry against steel
FiberSpeed is a diamond coating which is optimised for the special re-quirements of machining fibre re-inforced plastics (CRP, GRP) and has ideal adhesive properties. The high surface quality counteracts any possible adhesive tendencies of the machined materials. Due to its very thick multi-layer composition with 9.0 µm it can be used extremely long.
CCDia® MultiSpeed Thin
Type CVD coatingMaterial diamondMicro hardness > 10,000 VHN0.05
Coating thickness 3.0 µm ± 1.0Frictional value* –Max. application temperature
700 °C
Coating colour dark greyvhf tools ■ single tooth cutters Varius®
■ double tooth cutters with polished flute
Please note: Diamond is an insulator, i. e. there is no measur-ing by means of electric contact possible.* dry against steel
The high-end coating MultiSpeed combines an optimised coating adhe-sion with a smooth surface and an ex-tremely high wear volume. This multi-layer coating also has crack-stopping properties which lead to additional endurance. As it is a relatively thin dia-mond coating, the cutting edges will nearly not be rounded off. Thus it is especially suitable for all non-ferrous metals (also in combination with fibre materials) and wood.
Carbide Tools | Diamond Tools 13
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Overview of carbide and diamond tools
Cutters with polished fluteThis tool has a mirror finished polished flute, so the risk of clogging is very low. Thus this tool is ideal for milling extruded acrylic glass. Page 26
Cutters with hawk beak profileIdeal for milling aluminium due to a very sharp and exposed cutting edge with ex-treme grinding and large flute. Available with AluSpeed® coating. M Page 28
Varius® cuttersThis universal tool of our own brand Var-ius® has a favourable cost/performance ratio. It is also available with two kinds of coatings. M Page 22
Single tooth cuttersThese tools are mainly used for machining wood, plas-tics and non-ferrous metals.
Cutters with undercutThanks to the extra long undercut of this hawk beak cutter you can mill very deep slots. Ideal for machining aluminium, also in form of profiles. M Page 30
New
Cutters, polished, with left-hand twistThe single tooth cutter with polished flute is also available with a left-hand twist. Very handy for small workpieces and vacuum tables. M Page 33
V-slot cutters for compositesAn extra balanced carbide tool for cham-fering aluminium composites. It runs very smoothly and achieves especially high rates of feed. M Page 34
Varius® cuttersWith its two cutting edges, this version of our milling cutter Varius® is suitable for working on harder sorts of aluminium and softer ferrous metals. M Page 36
Double tooth cuttersSuitable for harder sorts of wood, plastics and non-fer-rous metals and for softer sorts of ferrous metals.
Cutters with fishtailDue to its fishtail grinding, this milling cut-ter can dip into hard materials quite eas-ily. It has a cost/performance ratio which is nearly unbeatable. M Page 38
HSC cuttersWith its especially steep spiral flute (15°), this milling cutter enables high rates of feed as the chips are removed very quickly. M Page 39
Cutters for aluminiumWith its 45° spiral flute, this milling cutter creates especially smooth edges of cut; optionally it is available with AluSpeed®
coating. M Page 40
Cutter for aluminium profilesA tool with very good immersion features and a short cutting edge for high feed rates. Especially suitable for window and door making. M Page 41
Varius® cutters with left-hand twistOur single tooth cutter Varius® is also avail-able with a left-hand twist, i. e. the work-piece will be pressed downwards while it is being machined. M Page 32
Cutters with face radiusThe cutting edge of this tool is semi-circu-lar rounded for optimum results in three-dimensional moulds or models without disturbing steps. M Page 31
Cutters with polished flute25° spiral flute, extremely sharp polished cutting edges with radial relief grinding; due to its two cutting edges especially great running smoothness. M Page 37
New
New
New
Carbide Tools | Diamond Tools14
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Cutters for stainless steelThis torus cutter has a small edge radius. Thus its wear resistance is increased and you will receive a very good surface qual-ity. M Page 42
Cutters with face radiusThis double tooth cutter with its semi-circular face radius is suitable for machin-ing harder materials three-dimensionally. M Page 44
Cutters for woodThis almost straightly slotted tool exerts only low drag forces on the workpiece; thus a fraying of the edges of cut will be prevented. M Page 43
Cutters with torus and undercutThe two cutters with undercut make up an ideally matching mould making duo. With its torus grinding, this one is the roughing specialist. M Page 45
New
New
Varius® cuttersOur Varius® milling cutter with three cut-ting edges is especially suitable for steel. Its TiAlN coating facilitates an excellent en-durance. M Page 50
Varius® cuttersThe four-toothed Varius® is ideal for very hard materials, e. g. for milling tempered steel, cast and other sorts of material which are difficult to machine. M Page 54
Cutters for stainless steelFor milling stainless steel, this triple tooth cutter has an especially shaped and very short cutting edge as well as a HARDLOX® coating. M Page 52
Cutters for foamThe cutting edge geometry is optimised for milling foam without fringing its verti-cal edges and for achieving plain surfaces when milling pockets. M Page 51
Ratio cuttersMilling cutter with different lead angles of its four flutes. This asymmetry facilitates a vibration-free running and counteracts the “cork-screw effect”. M Page 55
Four tooth cuttersMainly suitable for machining ferrous metals and other sorts of material which are difficult to machine.
Triple tooth cuttersSuitable for machining harder sorts of materials, on top of that we have extra long triple tooth cutters for foam.
Rub out cuttersIts shortened cutting edge and very sharp grinding make this cutter ideal for remov-ing larger copper areas from printed cir-cuit boards (rub out areas). M Page 47
Cutters with radius and undercutThe two cutters with undercut make up an ideally matching mould making duo. With its face radius, this one is the finishing spe-cialist. M Page 46
New
Carbide Tools | Diamond Tools 15
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Composite cuttersWith cross cut, diamond or spiral toothing; for highly abrasive materials like GRP or CRP.
Finely toothed cuttersMilling cutter with a fine-staggered tooth system of 10 – 14 micro-teeth rows. Due to its 30° right hand twist, the chips can be well removed. M Page 62
Finely toothed cutters, chip-breakerMilling cutter with a fine-staggered tooth system of 10 – 14 micro-teeth rows and an integrated chip breaker flute. So long chips will be chopped. M Page 63
NewNew
Roughing cutters for copperCentre-cutting tool with three cutting edges and chip splitter for an especially ef-ficient machining; 30° spiral flute and ad-ditional edge chamfer. M Page 58
Finishing cutters for copperDue to three different spiral angles and micro supporting chamfer at its perimeter especially smooth running characteristics; polished cutting edges. M Page 60
Roughing cutters for graphiteCentre-cutting tool with three or four cut-ting edges and chip splitter; with SHC coating for an extra long endurance. M Page 59
New
New
New
Roughing and finishing cuttersFor an especially efficient machining while roughing re-spectively extra low-vibration running while finishing.
Straightly slotted honeycomb cuttersFive tooth cutter with opposed chip break-ers. Due to its straight flute, the chips can be well removed and no tractive forces are exerted on the workpiece. M Page 66
Spiral-fluted honeycomb cuttersSix tooth cutter with opposed chip break-ers and a 10° right hand twist. So there is only a slight tractive force exerted on the workpiece. M Page 67
PCB outline cutters, diamond-toothedThis milling cutter is especially suitable for milling the outlines of printed circuit boards. Its diamond-toothing facilitates a high endurance. M Page 68
PCB outline cutters, spiral-toothedAlso suitable for milling the outlines of PCBs. Its spiral-toothing facilitates a better chip-clearance which leads to smoother surfaces. M Page 69
Medium-toothed cuttersMilling cutter with a medium-staggered tooth system of 8 – 12 micro-teeth rows and a 25° right hand twist. The fibres will be sheared off accurately. M Page 64
Coarsely toothed cuttersCoarse-staggered tooth system of 6 – 8 mi-cro-teeth rows and a 20° right hand twist. Like all toothed composite cutters with double-tooth face grinding. M Page 65
NewNew
NewNew
Carbide Tools | Diamond Tools16
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Router bitsMassive steel body with integrated carbide cutting edges; for wood, plastics and composite plates.
V slot cuttersAvailable with 60° or 90° top angle and two or three cutting edges; for milling (decoration) slots as well as for chamfering and engraving. M Page 86
Long hole slot cuttersStraightly slotted tool with negative cut-ting angle for perfectly even surfaces; For producing tongue and groove or mortice and tenon joints. M Page 87
Deburring toolsFor deburring, countersinking, chamfering of non-fer-rous metals and plastics.
Deburring toolsThis tool is used for deburring, counter-sinking, chamfering of non-ferrous metals and plastics; available with 60° to 120° top angle. M Page 82
Deburring tools, quadrantThe quadrant grinding of this tool creates smooth round chamferings on your work-pieces of plastics or non-ferrous metals. M Page 83
Engraver’s milling cutters for acrylicThis engraver’s milling cutter is equipped with a flute. So chips can be removed bet-ter and engravings in acrylic glass become clean-cut and burr-free. M Page 75
Engraver’s milling cutters for steelEngraving stainless steel needs an engrav-er’s milling cutter with a special cutting edge to achieve clear results and a long endurance. M Page 76
Isolation engraving toolOur special tool for engraving isolation channels on printed circuit boards and other hard materials. The results become burr-free and clean-cut. M Page 78
Channel cuttersGraver with 180° top angle, for milling die channels in pressed paper sheets or high pressure laminates, also suitable for usage in packaging industry. M Page 77
Semi-finished graversWe can deliver our gravers also in a semi-finished state with preground profile which you can finish according to your de-mands. M Page 79
New
New
Engraving toolsEngraver’s milling cutters and gravers for machining materials from plastics to stainless steel.
GraversOur classic gravers for engraving plastics, wood and non-ferrous metals with top an-gles from 15° on (ideal for working with-out workpiece levelling). M Page 72
Box graversA special kind of graver with a top angle of 92°. This tool is very well suitable for tasks like edge bending, e. g. for cabinet mak-ers. M Page 74
Carbide Tools | Diamond Tools 17
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Cutters for aluminium compositesThese V slot cutters are used for bending aluminium composites with a thickness of 3 mm to 6 mm. They are available with two different top angles. M Page 93
Cutters with quadrant A double tooth cutter with quadrant grinding for milling accurately rounded edges or appropriate internal profiles M Page 92
Thread cuttersUsing these tools you can cut threads in plastics, non-ferrous or ferrous metals and composites.
Thread whirling cuttersThese tools are suitable for tiny threads from M 1 on. They will be machined down to the bottom of the pre-drilled (tapped blind) hole. M Page 96
Circular thread cuttersA special tool which offers the possibility to drill the hole and to cut the thread in one working cycle. You save the time of the tool changing process. M Page 97
DrillsFor plastics, non-ferrous metals, printed circuit boards or thermosetting plastics and thermoplastics.
Drills with 3 mm shankThese drills with diameters from 0.2 mm to 6 mm are optimally suited for plastics and printed circuit boards, also well suit-able for non-ferrous metals. M Page 100
Drills with 6 mm shankA drill with a top angle of 130° for machin-ing non-ferrous metals or thermoplastics, but also suitable for wood or composites. M Page 102
New
New
Triple tooth surface milling cuttersMassive steel shank with a carbide head soldered on it; for an efficient surface mill-ing of larger areas of wood, MDF, plastics, and aluminium. M Page 94
New
Chamfering cuttersStraightly slotted tool with two cutting edges for chamfering accurately. The tool is available with three different chamfering angles. M Page 91
Radius cuttersDouble-toothed cutter (partly made of sol-id carbide) with semi-circular tool tip for milling rounded slots and for mould mak-ing. M Page 90
Slot cuttersA straightly slotted tool which is radi-ally ground for perfect surfaces; for mill-ing plane surfaces, notches, tongue and groove joints etc. M Page 88
Character cutterSpecial cutter with a top angle of 60° and a top radius; suitable for effectively remov-ing the material around free standing let-ters. M Page 89
Carbide Tools | Diamond Tools18
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Diamond toolsA diamond instead of a carbide cutting edge improves the quality and endurance – without cooling.
PCD single tooth cuttersCentre-cutting tool with a polycrystalline diamond; suitable for machining softer sorts of plastics, non-ferrous metals and wood. M Page 110
PCD double tooth cuttersThe second cutting edge again extends the endurance and enables a slightly im-proved smoothness. This milling cutter is ideal for harder materials. M Page 111
MCD polishing cuttersYou can produce polished acrylic glass let-ters or logos of any shape completely on your milling system. Polishing machines become dispensable. M Page 112
MCD polishing graversWith its diamond, it polishes engravings on sophisticated acrylic glass signboards to a high gloss. It is available with a top an-gle of 60° and 90°. M Page 113
PCD polishing graversDue to its extra long cutting edge, this tool is also suitable for very deep engravings. It is available with either 60° or 90° top an-gle. M Page 115
PCD polishing cuttersThanks to its less expensive polycrystalline diamond cutting edge suitable for much thicker materials than the monocrystalline diamond tools. M Page 114
CVD cuttersMilling cutter with one or two cutting edg-es which distinguish themselves by their especially great hardness and endurance; ideal for abrasive materials. M Page 116
Impression toolsWith appropriate shank and stop ring for use in the mill-ing machines of the Impression line.
Goldsmith toolsA selection of tools from the vhf product range which are suitable for typical gold-smith works in materials like wax, metal and plastics. M Page 118
NewNew
New
New
Lances and knivesLances and knives for the different cutting heads and the universal head.
LancesWe offer different kinds of lances for the use in tangential cutting heads. The larg-est choice is available for the oscillating tangential cutting head. M Page 106
KnivesHere you will find several replacement knives for the drag knife unit and for the various attachments of the universal head. M Page 107
Carbide Tools | Diamond Tools 19
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Carbide Tools | Diamond Tools20
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Single Tooth CuttersOn the following pages you'll find an impres-sive range of single tooth cutters – with more than 250 different geometries! Especially suit-able for wood, plastics and non-ferrous metals; also with left-hand twist.
Varius® cutters
Cutters with polished flute
Cutters with hawk beak profile
Cutters with undercut
Cutters with face radius
Varius® cutters with left-hand twist
Polished cutters with left-hand twist
V-slot cutters for aluminium composites
Free delivery at shop.vhf.de
L1L2
D2 D1Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-SC-0020-3-006-40 0.20 mm 3 mm 0.6 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-SC-0050-3-015-40 0.50 mm 3 mm 1.5 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0060-3-030-40 0.60 mm 3 mm 3.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0070-3-040-40* 0.70 mm 3 mm 4.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0080-3-040-40 0.80 mm 3 mm 4.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0100-3-030-40* 1.00 mm 3 mm 3.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0100-3-050-40 1.00 mm 3 mm 5.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0100-6-050-40 1.00 mm 6 mm 5.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0120-3-050-40* 1.20 mm 3 mm 5.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0150-3-050-40 1.50 mm 3 mm 5.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0150-6-050-40* 1.50 mm 6 mm 5.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0160-3-060-40 1.60 mm 3 mm 6.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0180-3-070-40 1.80 mm 3 mm 7.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0200-3-050-40* 2.00 mm 3 mm 5.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0200-3-080-40 2.00 mm 3 mm 8.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0200-4-070-40 2.00 mm 4 mm 7.0 mm 40 mm 19.00 18.05 17.10 16.15 15.20ES-SC-0200-6-050-40* 2.00 mm 6 mm 5.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0200-6-070-40 2.00 mm 6 mm 7.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60ES-SC-0250-3-100-40 2.50 mm 3 mm 10.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0250-6-100-50* 2.50 mm 6 mm 10.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ES-SC-0300-3-050-40 3.00 mm 3 mm 5.0 mm 40 mm 13.00 12.35 11.70 11.05 10.40ES-SC-0300-3-100-30* 3.00 mm 3 mm 10.0 mm 30 mm 14.00 13.30 12.60 11.90 11.20ES-SC-0300-3-100-40 3.00 mm 3 mm 10.0 mm 40 mm 14.00 13.30 12.60 11.90 11.20ES-SC-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 15.00 14.25 13.50 12.75 12.00ES-SC-0300-4-100-40 3.00 mm 4 mm 10.0 mm 40 mm 19.00 18.05 17.10 16.15 15.20ES-SC-0300-6-050-40 3.00 mm 6 mm 5.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-SC-0300-6-080-50* 3.00 mm 6 mm 8.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0300-6-100-50 3.00 mm 6 mm 10.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ES-SC-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40
...
Single tooth cutters Varius®
Description:With our own brand Varius® we have developed a series of milling cutters with one to four cutting edges. They distinguish themselves by a universal applicability and a long endurance. This type is made of finest grain car-bide and it has a 30° spiral flute.
Coating:Many of these milling cutters are available with an SHC® coating which consists of super-hard carbon (see page 12). On top of that, some diameters are available with the diamond coating CCDia® MultiSpeed Thin (see page 13).
Fields of application:This universal single tooth cutter is suitable for milling aluminium (also aluminium composite plates), copper, zinc, brass, cast acrylic glass and plastics which do not tend to smear. With SHC® coating it is especially suitable for (composite) materials with a considerable part of glue/resin (e. g. MDF, multiplex panels, chipboards) or thermosetting plastics (Bakelite®, Pertinax, HPL, ...). All-rounders: single tooth cutters of finest grain carbide.
26new
tools
Carbide Tools | Diamond Tools22
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esSi
ngle
Too
th
Cut
ters
L1L2
D2 D1
Non-ferr.Metals
PlasticsRigid Foam
Wood
Continuation
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-SC-0330-6-160-50* 3.30 mm 6 mm 16.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0350-6-140-50* 3.50 mm 6 mm 14.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0400-4-060-40 4.00 mm 4 mm 6.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ES-SC-0400-4-100-40 4.00 mm 4 mm 10.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-SC-0400-4-140-50 4.00 mm 4 mm 14.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40ES-SC-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 20.00 19.00 18.00 17.00 16.00ES-SC-0400-6-060-40 4.00 mm 6 mm 6.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ES-SC-0400-6-180-60* 4.00 mm 6 mm 18.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0420-6-160-50* 4.20 mm 6 mm 16.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0450-6-140-50* 4.50 mm 6 mm 14.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0500-5-120-50* 5.00 mm 5 mm 12.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20ES-SC-0500-5-160-60 5.00 mm 5 mm 16.0 mm 60 mm 20.00 19.00 18.00 17.00 16.00ES-SC-0500-6-070-40* 5.00 mm 6 mm 7.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0500-6-140-50 5.00 mm 6 mm 14.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ES-SC-0550-6-140-50* 5.50 mm 6 mm 14.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0600-6-050-40* 6.00 mm 6 mm 5.0 mm 40 mm 19.00 18.05 17.10 16.15 15.20ES-SC-0600-6-080-40 6.00 mm 6 mm 8.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-SC-0600-6-140-50 6.00 mm 6 mm 14.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ES-SC-0600-6-200-60 6.00 mm 6 mm 20.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60ES-SC-0600-6-250-60 6.00 mm 6 mm 25.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0800-8-140-50* 8.00 mm 8 mm 14.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ES-SC-0800-8-200-60* 8.00 mm 8 mm 20.0 mm 60 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0800-8-250-75 8.00 mm 8 mm 25.0 mm 75 mm 29.00 27.55 26.10 24.65 23.20ES-SC-0800-8-350-85* 8.00 mm 8 mm 35.0 mm 85 mm 39.00 37.05 35.10 33.15 31.20ES-SC-1000-10-140-50* 10.00 mm 10 mm 14.0 mm 50 mm 34.00 32.30 30.60 28.90 27.20ES-SC-1000-10-250-75 10.00 mm 10 mm 25.0 mm 75 mm 39.00 37.05 35.10 33.15 31.20ES-SC-1000-10-280-75* 10.00 mm 10 mm 28.0 mm 75 mm 41.00 38.95 36.90 34.85 32.80ES-SC-1200-12-250-75 12.00 mm 12 mm 25.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20
* new tool in this printed issue | * new tool in this PDF updateCoated tools on the next double page...
Carbide Tools | Diamond Tools 23
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Single Tooth C
utters
L1L2
D2 D1
Varius® cutters with SHC and diamond coating.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With SHC® coating, thickness 2.0 µm ± 0.2:ES-SC-0100-3-030-40-SHC* 1.00 mm 3 mm 3.0 mm 40 mm 23.00 21.85 20.70 19.55 18.40ES-SC-0100-6-050-40-SHC* 1.00 mm 6 mm 5.0 mm 40 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0150-6-050-40-SHC* 1.50 mm 6 mm 5.0 mm 40 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0200-6-050-40-SHC* 2.00 mm 6 mm 5.0 mm 40 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0200-6-070-40-SHC 2.00 mm 6 mm 7.0 mm 40 mm 28.00 26.60 25.20 23.80 22.40ES-SC-0300-3-100-40-SHC 3.00 mm 3 mm 10.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-SC-0300-6-050-40-SHC 3.00 mm 6 mm 5.0 mm 40 mm 26.00 24.70 23.40 22.10 20.80ES-SC-0300-6-080-50-SHC* 3.00 mm 6 mm 8.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0300-6-100-50-SHC 3.00 mm 6 mm 10.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-SC-0300-6-120-50-SHC* 3.00 mm 6 mm 12.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-SC-0330-6-160-50-SHC* 3.30 mm 6 mm 16.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-SC-0350-6-140-50-SHC* 3.50 mm 6 mm 14.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-SC-0400-4-140-50-SHC 4.00 mm 4 mm 14.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-SC-0400-6-060-40-SHC 4.00 mm 6 mm 6.0 mm 40 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0400-6-120-50-SHC 4.00 mm 6 mm 12.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-SC-0400-6-180-60-SHC* 4.00 mm 6 mm 18.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20ES-SC-0420-6-160-50-SHC* 4.20 mm 6 mm 16.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-SC-0450-6-140-50-SHC* 4.50 mm 6 mm 14.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-SC-0500-5-160-60-SHC* 5.00 mm 5 mm 16.0 mm 60 mm 26.00 24.70 23.40 22.10 20.80ES-SC-0500-5-160-75-SHC* 5.00 mm 5 mm 16.0 mm 75 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0500-6-070-40-SHC* 5.00 mm 6 mm 7.0 mm 40 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0500-6-140-50-SHC 5.00 mm 6 mm 14.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-SC-0600-6-050-40-SHC* 6.00 mm 6 mm 5.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-SC-0600-6-080-40-SHC 6.00 mm 6 mm 8.0 mm 40 mm 26.00 24.70 23.40 22.10 20.80ES-SC-0600-6-140-50-SHC 6.00 mm 6 mm 14.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-SC-0600-6-200-60-SHC 6.00 mm 6 mm 20.0 mm 60 mm 28.00 26.60 25.20 23.80 22.40ES-SC-0600-6-250-60-SHC 6.00 mm 6 mm 25.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20
...
20new
toolsDimensions and prices
Single tooth cutters Varius® with coating
Description:The coated Varius® types have a great dry running performance and do not tend to clog too easily. Their already long endurance will be prolonged considerably.
Coating:Most of these milling cutters are available with an SHC® coating which consists of super-hard carbon (see page 12). On top of that, some diameters are available with the diamond coating CCDia® MultiSpeed Thin (see page 13).
Fields of application:Tools with SHC® coating it is especially suitable for (com-posite) materials with a considerable part of glue/resin (e. g. MDF, multiplex panels, chipboards) or thermoset-ting plastics (Bakelite®, Pertinax, HPL, ...). Tools coated with CCDia® MultiSpeed Thin are especially suitable for all non-ferrous metals (also in combination with fibre materials) and wood.
Carbide Tools | Diamond Tools24
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esSi
ngle
Too
th
Cut
ters
Sing
le T
ooth
C
utte
rs
L1L2
D2 D1Continuation
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-SC-0800-8-140-50-SHC* 8.00 mm 8 mm 14.0 mm 50 mm 33.00 31.35 29.70 28.05 26.40ES-SC-0800-8-200-60-SHC* 8.00 mm 8 mm 20.0 mm 60 mm 35.00 33.25 31.50 29.75 28.00ES-SC-0800-8-250-75-SHC 8.00 mm 8 mm 25.0 mm 75 mm 37.00 35.15 33.30 31.45 29.60ES-SC-1000-10-250-75-SHC 10.00 mm 10 mm 25.0 mm 75 mm 47.00 44.65 42.30 39.95 37.60
With CCDia® MultiSpeed Thin, thickness 3.0 µm ± 1.0:1
ES-SC-0300-3-100-40-MST* 3.00 mm 3 mm 10.0 mm 40 mm 28.00 26.60 25.20 23.80 22.40ES-SC-0400-4-140-50-MST* 4.00 mm 4 mm 14.0 mm 50 mm 38.00 36.10 34.20 32.30 30.40ES-SC-0600-6-140-50-MST* 6.00 mm 6 mm 14.0 mm 50 mm 48.00 45.60 43.20 40.80 38.40
* new tool in this printed issue1 as the diamond layer is an electrical isolator, these tools are not suitable for a measurement with the automatic z adjustment.Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Non-ferr.Metals
PlasticsWoodCompo-
sites
Carbide Tools | Diamond Tools 25
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Single Tooth C
utters
L1
D2 D1
L2
Single tooth cutters with polished flute
Description:This single tooth cutter has a mirror finished polished flute with a lead angle of 25°. So the risk of clogging is low and the chip clearance is very good. The cut-ting edge of this tool is extremely sharp and faceted. So the results will become very smooth even at high rates of feed.
Fields of application:This tool has been developed especially for working on extruded acrylic glass; however, it is also very well suit-able for working on soft wood and thermoplastics.
The original – often copied, but still unmatched.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-PS-0100-3-040-40 1.00 mm 3 mm 4.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0100-6-050-50* 1.00 mm 6 mm 5.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-PS-0150-3-060-40 1.50 mm 3 mm 6.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0200-2-080-30 2.00 mm 2 mm 8.0 mm 30 mm 19.00 18.05 17.10 16.15 15.20ES-PS-0200-3-050-40* 2.00 mm 3 mm 5.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0200-3-080-30* 2.00 mm 3 mm 8.0 mm 30 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0200-3-080-40 2.00 mm 3 mm 8.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0200-3-090-40* 2.00 mm 3 mm 9.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0200-3-110-40* 2.00 mm 3 mm 11.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0200-6-050-50* 2.00 mm 6 mm 5.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-PS-0200-6-080-50 2.00 mm 6 mm 8.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-PS-0250-3-100-40* 2.50 mm 3 mm 10.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0300-3-080-40* 3.00 mm 3 mm 8.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-PS-0300-3-100-30 3.00 mm 3 mm 10.0 mm 30 mm 18.00 17.10 16.20 15.30 14.40ES-PS-0300-3-120-40 3.00 mm 3 mm 12.0 mm 40 mm 19.00 18.05 17.10 16.15 15.20ES-PS-0300-3-120-60 3.00 mm 3 mm 12.0 mm 60 mm 20.00 19.00 18.00 17.00 16.00ES-PS-0300-3-160-50* 3.00 mm 3 mm 16.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ES-PS-0300-3-220-60 3.00 mm 3 mm 22.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60ES-PS-0300-4-120-50* 3.00 mm 4 mm 12.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0300-6-050-50* 3.00 mm 6 mm 5.0 mm 50 mm 26.00 24.70 23.40 22.10 20.80ES-PS-0300-6-080-50* 3.00 mm 6 mm 8.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-PS-0300-6-100-50 3.00 mm 6 mm 10.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-PS-0300-6-120-50 3.00 mm 6 mm 12.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0300-6-160-50* 3.00 mm 6 mm 16.0 mm 50 mm 30.00 28.50 27.00 25.50 24.00ES-PS-0300-6-220-60* 3.00 mm 6 mm 22.0 mm 60 mm 31.00 29.45 27.90 26.35 24.80ES-PS-0400-4-080-40* 4.00 mm 4 mm 8.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-PS-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ES-PS-0400-4-160-50* 4.00 mm 4 mm 16.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60
...
42new
tools
Carbide Tools | Diamond Tools26
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esSi
ngle
Too
th
Cut
ters
L1
D2 D1
L2
If the tool has finished its lifetime and is no longer sharp enough for milling acrylic glass, you can still use it for machining alumini-um composite plates or similar materials.
Practical Tip
PlasticsRigid Foam
Wood
Continuation
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-PS-0400-4-220-60 4.00 mm 4 mm 22.0 mm 60 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0400-4-320-70 4.00 mm 4 mm 32.0 mm 70 mm 26.00 24.70 23.40 22.10 20.80ES-PS-0400-6-060-50* 4.00 mm 6 mm 6.0 mm 50 mm 26.00 24.70 23.40 22.10 20.80ES-PS-0400-6-080-50* 4.00 mm 6 mm 8.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-PS-0400-6-100-50* 4.00 mm 6 mm 10.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-PS-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0400-6-160-50* 4.00 mm 6 mm 16.0 mm 50 mm 30.00 28.50 27.00 25.50 24.00ES-PS-0400-6-220-60* 4.00 mm 6 mm 22.0 mm 60 mm 31.00 29.45 27.90 26.35 24.80ES-PS-0500-5-120-50* 5.00 mm 5 mm 12.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ES-PS-0500-5-160-60 5.00 mm 5 mm 16.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ES-PS-0500-5-320-70 5.00 mm 5 mm 32.0 mm 70 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0500-6-140-50 5.00 mm 6 mm 14.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-PS-0500-6-220-60* 5.00 mm 6 mm 22.0 mm 60 mm 31.00 29.45 27.90 26.35 24.80ES-PS-0540-6-140-50* 5.40 mm 6 mm 14.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-PS-0540-6-270-70* 5.40 mm 6 mm 27.0 mm 70 mm 31.00 29.45 27.90 26.35 24.80ES-PS-0600-6-100-50* 6.00 mm 6 mm 10.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ES-PS-0600-6-140-50 6.00 mm 6 mm 14.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-PS-0600-6-220-60 6.00 mm 6 mm 22.0 mm 60 mm 26.00 24.70 23.40 22.10 20.80ES-PS-0600-6-320-70 6.00 mm 6 mm 32.0 mm 70 mm 31.00 29.45 27.90 26.35 24.80ES-PS-0600-6-420-80 6.00 mm 6 mm 42.0 mm 80 mm 36.00 34.20 32.40 30.60 28.80ES-PS-0800-8-140-50* 8.00 mm 8 mm 14.0 mm 50 mm 34.00 32.30 30.60 28.90 27.20ES-PS-0800-8-220-60 8.00 mm 8 mm 22.0 mm 60 mm 39.00 37.05 35.10 33.15 31.20ES-PS-0800-8-320-70* 8.00 mm 8 mm 32.0 mm 70 mm 44.00 41.80 39.60 37.40 35.20ES-PS-0800-8-420-80* 8.00 mm 8 mm 42.0 mm 80 mm 49.00 46.55 44.10 41.65 39.20ES-PS-1000-10-140-60* 10.00 mm 10 mm 14.0 mm 60 mm 39.00 37.05 35.10 33.15 31.20ES-PS-1000-10-220-70* 10.00 mm 10 mm 22.0 mm 70 mm 44.00 41.80 39.60 37.40 35.20ES-PS-1000-10-320-75 10.00 mm 10 mm 32.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20ES-PS-1200-12-300-75 12.00 mm 12 mm 30.0 mm 75 mm 59.00 56.05 53.10 50.15 47.20
With undercut:ES-PS-0100-6-050-0120-50* 1.00 mm 6 mm 5.0 mm 12.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0200-6-080-0160-50* 2.00 mm 6 mm 8.0 mm 16.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0300-6-100-0220-50* 3.00 mm 6 mm 10.0 mm 22.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0400-6-120-0220-50* 4.00 mm 6 mm 12.0 mm 22.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0500-6-140-0220-50* 5.00 mm 6 mm 14.0 mm 22.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20ES-PS-0600-6-140-0220-50* 6.00 mm 6 mm 14.0 mm 22.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ES-PS-0800-8-140-0220-50* 8.00 mm 8 mm 14.0 mm 22.0 mm 50 mm 35.00 33.25 31.50 29.75 28.00ES-PS-0800-8-220-0420-75* 8.00 mm 8 mm 22.0 mm 42.0 mm 75 mm 42.00 39.90 37.80 35.70 33.60ES-PS-1000-10-140-0220-60* 10.00 mm 10 mm 14.0 mm 22.0 mm 60 mm 40.00 38.00 36.00 34.00 32.00ES-PS-1000-10-220-0320-70* 10.00 mm 10 mm 22.0 mm 32.0 mm 70 mm 45.00 42.75 40.50 38.25 36.00ES-PS-1000-10-220-0420-75* 10.00 mm 10 mm 22.0 mm 42.0 mm 75 mm 47.00 44.65 42.30 39.95 37.60
* new tool in this printed issue | * new tool in this PDF updateAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Carbide Tools | Diamond Tools 27
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Single Tooth C
utters
L1
D2 D1
L2
Single tooth cutters with hawk beak
Description:This single tooth cutter has a very sharp, exposed cut-ting edge (“hawk beak”) with an extreme grinding. The large flute with a lead angle of 30° enables a very good chip clearance. So the risk is low that the tool may clog during milling, also in softer sorts of aluminium.
Coating:Many tools are optionally available with the high perfor-mance coating AluSpeed® (see page 11).
Fields of application:Special milling cutter for aluminium; however, also very good results in plastics and wood. The coated tools are suitable for machining aluminium with a silicon part of up to 10 %, copper and other non-ferrous metals.
Practical tip:Choose appropriately short cutting edges (ideal in com-bination with increased shanks) for milling works or feed rates in the threshold range.This hawk beak is especially keen on aluminium...
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-HB-0100-3-030-40* 1.00 mm 3 mm 3.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0100-3-050-40* 1.00 mm 3 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0100-6-050-40* 1.00 mm 6 mm 5.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0150-3-050-40* 1.50 mm 3 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0200-3-050-40* 2.00 mm 3 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0200-3-060-40* 2.00 mm 3 mm 6.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0200-3-080-40 2.00 mm 3 mm 8.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0200-4-070-40 2.00 mm 4 mm 7.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-HB-0200-6-050-40* 2.00 mm 6 mm 5.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0200-6-070-40 2.00 mm 6 mm 7.0 mm 40 mm 23.00 21.85 20.70 19.55 18.40ES-HB-0200-6-070-50* 2.00 mm 6 mm 7.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-HB-0250-3-100-40* 2.50 mm 3 mm 10.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0300-3-060-40* 3.00 mm 3 mm 6.0 mm 40 mm 14.00 13.30 12.60 11.90 11.20ES-HB-0300-3-100-40 3.00 mm 3 mm 10.0 mm 40 mm 15.00 14.25 13.50 12.75 12.00ES-HB-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ES-HB-0300-4-100-40 3.00 mm 4 mm 10.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-HB-0300-6-050-40 3.00 mm 6 mm 5.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-HB-0300-6-080-50* 3.00 mm 6 mm 8.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0300-6-100-50 3.00 mm 6 mm 10.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-HB-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-0350-6-140-50* 3.50 mm 6 mm 14.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-0400-4-060-40 4.00 mm 4 mm 6.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ES-HB-0400-4-100-40 4.00 mm 4 mm 10.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0400-4-140-50 4.00 mm 4 mm 14.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20ES-HB-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 21.00 19.95 18.90 17.85 16.80ES-HB-0400-6-060-40 4.00 mm 6 mm 6.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-HB-0400-6-180-60* 4.00 mm 6 mm 18.0 mm 60 mm 24.00 22.80 21.60 20.40 19.20ES-HB-0450-6-140-50* 4.50 mm 6 mm 14.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20
...
39new
tools
Carbide Tools | Diamond Tools28
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esSi
ngle
Too
th
Cut
ters
L1
D2 D1
L2
Non-ferr.Metals
PlasticsWood
Continuation
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-HB-0500-5-160-60 5.00 mm 5 mm 16.0 mm 60 mm 21.00 19.95 18.90 17.85 16.80ES-HB-0500-6-070-40* 5.00 mm 6 mm 7.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0500-6-140-50 5.00 mm 6 mm 14.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-HB-0550-6-140-50* 5.50 mm 6 mm 14.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-0600-6-050-40 6.00 mm 6 mm 5.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-HB-0600-6-060-40* 6.00 mm 6 mm 6.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-HB-0600-6-080-40 6.00 mm 6 mm 8.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-HB-0600-6-140-50 6.00 mm 6 mm 14.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0600-6-200-60 6.00 mm 6 mm 20.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ES-HB-0600-6-250-60 6.00 mm 6 mm 25.0 mm 60 mm 24.00 22.80 21.60 20.40 19.20ES-HB-0800-8-060-40* 8.00 mm 8 mm 6.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-HB-0800-8-140-50 8.00 mm 8 mm 14.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-HB-0800-8-200-60* 8.00 mm 8 mm 20.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20ES-HB-0800-8-250-75 8.00 mm 8 mm 25.0 mm 75 mm 31.00 29.45 27.90 26.35 24.80ES-HB-0800-8-350-85* 8.00 mm 8 mm 35.0 mm 85 mm 41.00 38.95 36.90 34.85 32.80ES-HB-1000-10-140-50* 10.00 mm 10 mm 14.0 mm 50 mm 36.00 34.20 32.40 30.60 28.80ES-HB-1000-10-250-75 10.00 mm 10 mm 25.0 mm 75 mm 41.00 38.95 36.90 34.85 32.80ES-HB-1200-12-250-75 12.00 mm 12 mm 25.0 mm 75 mm 51.00 48.45 45.90 43.35 40.80
With AluSpeed® coating, thickness 2.0 µm ± 0.7:ES-HB-0200-3-060-40-AS* 2.00 mm 3 mm 6.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0200-3-080-40-AS* 2.00 mm 3 mm 8.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60ES-HB-0200-6-050-40-AS* 2.00 mm 6 mm 5.0 mm 40 mm 26.00 24.70 23.40 22.10 20.80ES-HB-0200-6-070-40-AS 2.00 mm 6 mm 7.0 mm 40 mm 27.00 25.65 24.30 22.95 21.60ES-HB-0300-3-060-40-AS* 3.00 mm 3 mm 6.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-HB-0300-3-100-40-AS 3.00 mm 3 mm 10.0 mm 40 mm 19.00 18.05 17.10 16.15 15.20ES-HB-0300-6-050-40-AS 3.00 mm 6 mm 5.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-HB-0300-6-080-50-AS* 3.00 mm 6 mm 8.0 mm 50 mm 26.00 24.70 23.40 22.10 20.80ES-HB-0300-6-100-50-AS 3.00 mm 6 mm 10.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-HB-0300-6-120-50-AS* 3.00 mm 6 mm 12.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-HB-0350-6-140-50-AS* 3.50 mm 6 mm 14.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-HB-0400-4-060-40-AS* 4.00 mm 4 mm 6.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-HB-0400-4-140-50-AS 4.00 mm 4 mm 14.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-HB-0400-4-220-60-AS* 4.00 mm 4 mm 22.0 mm 60 mm 27.00 25.65 24.30 22.95 21.60ES-HB-0400-6-060-40-AS 4.00 mm 6 mm 6.0 mm 40 mm 26.00 24.70 23.40 22.10 20.80ES-HB-0400-6-120-50-AS 4.00 mm 6 mm 12.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-HB-0400-6-180-60-AS* 4.00 mm 6 mm 18.0 mm 60 mm 28.00 26.60 25.20 23.80 22.40ES-HB-0450-6-140-50-AS* 4.50 mm 6 mm 14.0 mm 50 mm 28.00 26.60 25.20 23.80 22.40ES-HB-0500-6-070-40-AS* 5.00 mm 6 mm 7.0 mm 40 mm 26.00 24.70 23.40 22.10 20.80ES-HB-0500-6-140-50-AS 5.00 mm 6 mm 14.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60ES-HB-0600-6-050-40-AS 6.00 mm 6 mm 5.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-HB-0600-6-060-40-AS* 6.00 mm 6 mm 6.0 mm 40 mm 24.00 22.80 21.60 20.40 19.20ES-HB-0600-6-080-40-AS 6.00 mm 6 mm 8.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-HB-0600-6-140-50-AS 6.00 mm 6 mm 14.0 mm 50 mm 26.00 24.70 23.40 22.10 20.80ES-HB-0600-6-200-60-AS 6.00 mm 6 mm 20.0 mm 60 mm 27.00 25.65 24.30 22.95 21.60ES-HB-0600-6-250-60-AS 6.00 mm 6 mm 25.0 mm 60 mm 28.00 26.60 25.20 23.80 22.40ES-HB-0800-8-060-40-AS* 8.00 mm 8 mm 6.0 mm 40 mm 32.00 30.40 28.80 27.20 25.60ES-HB-0800-8-140-50-AS 8.00 mm 8 mm 14.0 mm 50 mm 34.00 32.30 30.60 28.90 27.20ES-HB-0800-8-200-60-AS* 8.00 mm 8 mm 20.0 mm 60 mm 36.00 34.20 32.40 30.60 28.80ES-HB-0800-8-250-75-AS 8.00 mm 8 mm 25.0 mm 75 mm 38.00 36.10 34.20 32.30 30.40ES-HB-1000-10-250-75-AS* 10.00 mm 10 mm 25.0 mm 75 mm 48.00 45.60 43.20 40.80 38.40
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Carbide Tools | Diamond Tools 29
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Single Tooth C
utters
L1L2
D2 D1L3
Non-ferr.Metals
PlasticsWood
Single tooth cutters with hawk beak and undercut
Description:With their undercut which is partly extra long, you can use these single tooth cutters for milling very deep slots. Their rather short spiral flute with a lead angle of 30° facilitates great stability and smooth running and enables high rates of feed.
The cutting edge has a hawk beak profile at its top, so the tool can immerse into the material quite easily. Furthermore, this profile reduces the risk that the cutter may clog during the milling process, also in softer sorts of aluminium. The tool is ideal for machining aluminium, also in form of profile bars. In addition to this it may be used for the pre-roughing process in three-dimensional machining.
Fields of application:Special cutter for aluminium, however very good results are also achieved in plastics and wood.
Milling in deep slots with a long undercut.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting
edge length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-HB-FS-0100-3-050-0100-40* 1.00 mm 3 mm 5.0 mm 10.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-HB-FS-0150-3-050-0100-40* 1.50 mm 3 mm 5.0 mm 10.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-HB-FS-0200-3-050-0120-40* 2.00 mm 3 mm 5.0 mm 12.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-HB-FS-0200-6-050-0120-50* 2.00 mm 6 mm 5.0 mm 12.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-FS-0300-3-050-0220-50* 3.00 mm 3 mm 5.0 mm 22.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ES-HB-FS-0300-6-050-0220-50* 3.00 mm 6 mm 5.0 mm 22.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-FS-0400-4-080-0220-50* 4.00 mm 4 mm 8.0 mm 22.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ES-HB-FS-0400-4-080-0320-60* 4.00 mm 4 mm 8.0 mm 32.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60ES-HB-FS-0400-6-080-0220-50* 4.00 mm 6 mm 8.0 mm 22.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-FS-0500-6-140-0220-50* 5.00 mm 6 mm 14.0 mm 22.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-FS-0500-6-140-0320-60* 5.00 mm 6 mm 14.0 mm 32.0 mm 60 mm 25.00 23.75 22.50 21.25 20.00ES-HB-FS-0600-6-140-0220-50* 6.00 mm 6 mm 14.0 mm 22.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ES-HB-FS-0600-6-140-0320-60* 6.00 mm 6 mm 14.0 mm 32.0 mm 60 mm 25.00 23.75 22.50 21.25 20.00ES-HB-FS-0600-6-140-0420-70* 6.00 mm 6 mm 14.0 mm 42.0 mm 70 mm 26.00 24.70 23.40 22.10 20.80ES-HB-FS-0800-8-140-0320-60* 8.00 mm 8 mm 14.0 mm 32.0 mm 60 mm 31.00 29.45 27.90 26.35 24.80ES-HB-FS-0800-8-140-0420-75* 8.00 mm 8 mm 14.0 mm 42.0 mm 75 mm 33.00 31.35 29.70 28.05 26.40ES-HB-FS-0800-8-140-0520-85* 8.00 mm 8 mm 14.0 mm 52.0 mm 85 mm 35.00 33.25 31.50 29.75 28.00ES-HB-FS-0800-8-220-0620-100* 8.00 mm 8 mm 22.0 mm 62.0 mm 100 mm 37.00 35.15 33.30 31.45 29.60ES-HB-FS-1000-10-250-0420-75* 10.00 mm 10 mm 25.0 mm 42.0 mm 75 mm 45.00 42.75 40.50 38.25 36.00
* new tool in this printed issue | * new tool in this PDF updateAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
Carbide Tools | Diamond Tools30
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esSi
ngle
Too
th
Cut
ters
L1
D2 D1
L2
Non-ferr.Metals
PlasticsRigid Foam
Wood
Single tooth cutters with face radius
Description:This single tooth cutter is due to its semi-circular face ra-dius perfectly suitable for tasks in the field of model and mould making. The tool has a radial relief grinding and its large flute with its 30° spiral enables a good chip clear-ance and thus high rates of feed.
Fields of application:This tool is suitable for milling three-dimensional moulds in wood, aluminium, copper, zinc, brass, cast acrylic glass and plastics.
Single tooth cutters with face radius for mould making.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-SCR-0100-3-050-40* 1.00 mm 3 mm 5.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SCR-0100-6-050-40* 1.00 mm 6 mm 5.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-SCR-0200-3-080-40 2.00 mm 3 mm 8.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SCR-0200-6-070-40 2.00 mm 6 mm 7.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-SCR-0300-3-100-40 3.00 mm 3 mm 10.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ES-SCR-0300-6-100-50 3.00 mm 6 mm 10.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ES-SCR-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-SCR-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ES-SCR-0500-6-140-50 5.00 mm 6 mm 14.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ES-SCR-0600-6-140-50 6.00 mm 6 mm 14.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ES-SCR-0800-8-200-60* 8.00 mm 8 mm 20.0 mm 60 mm 36.00 34.20 32.40 30.60 28.80ES-SCR-1000-10-220-75* 10.00 mm 10 mm 22.0 mm 75 mm 46.00 43.70 41.40 39.10 36.80
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
4new
tools
Carbide Tools | Diamond Tools 31
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Single Tooth C
utters
L1
D2 D1
L2
Non-ferr.Metals
PlasticsRigid Foam
Wood
The left-hand twist presses the workpiece downwards.
Single tooth cutters Varius®, left-hand twist
Description:Our universal single tooth cutter Varius® is also available with a 30° left-hand twisted flute. So the chips won’t be transported to the top but be pressed downwards into the milled slot, although the tool is right-cutting – like all vhf tools. An advantage of the left-hand twist is that the workpiece will be pressed downwards, too.
Fields of application:Especially when workpieces have to be milled on a vacu-um table with low holding force, the danger that the workpiece may loosen accidentally due to the cork-screw effect will be reduced considerably. The left-hand twist also shows advantages when working on thin materials or such which tend to fray easily. However, the removal rate is reduced a little bit. This tool is good for milling aluminium, copper, zinc, brass, acrylic glass, plastics...
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-SC-LD-0100-3-050-40 1.00 mm 3 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-SC-LD-0150-3-050-40 1.50 mm 3 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-SC-LD-0200-3-080-40 2.00 mm 3 mm 8.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-SC-LD-0300-3-100-40 3.00 mm 3 mm 10.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ES-SC-LD-0300-6-100-50 3.00 mm 6 mm 10.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40ES-SC-LD-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ES-SC-LD-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40 ES-SC-LD-0500-5-160-60* 5.00 mm 5 mm 16.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ES-SC-LD-0600-6-140-50 6.00 mm 6 mm 14.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40 ES-SC-LD-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 24.00 22.80 21.60 20.40 19.20ES-SC-LD-0800-8-220-75 8.00 mm 8 mm 22.0 mm 75 mm 33.00 31.35 29.70 28.05 26.40
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
2new
tools
Carbide Tools | Diamond Tools32
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esSi
ngle
Too
th
Cut
ters
L1
D2 D1
L2
PlasticsRigid Foam
Wood
Single tooth cutters, polished, left-hand twist
Description:Like the universal single tooth cutter Varius®, our single tooth cutters with polished flute are also available with a 25° left-hand twist. This milling cutter has a mirror finished polished flute. So the risk of clogging is low and the chip clearance is very good. The cutting edge of this tool is very sharp and the results will become very smooth even at high rates of feed.
Fields of application:This tool has been developed especially for working on extruded acrylic glass; however, it is also well suitable for working on other sorts of plastics and wood. We rec-ommend this tool especially for very thin plates or for trimming the edges of workpieces.
Cutters with left-hand twist for acrylic glass and plastics.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ES-PS-LD-0100-3-040-40 1.00 mm 3 mm 4.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-PS-LD-0150-3-060-40 1.50 mm 3 mm 6.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-PS-LD-0200-2-080-30 2.00 mm 2 mm 8.0 mm 30 mm 20.00 19.00 18.00 17.00 16.00ES-PS-LD-0200-3-080-40 2.00 mm 3 mm 8.0 mm 40 mm 25.00 23.75 22.50 21.25 20.00ES-PS-LD-0300-3-100-30 3.00 mm 3 mm 10.0 mm 30 mm 19.00 18.05 17.10 16.15 15.20ES-PS-LD-0300-3-120-40 3.00 mm 3 mm 12.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ES-PS-LD-0300-3-120-60 3.00 mm 3 mm 12.0 mm 60 mm 21.00 19.95 18.90 17.85 16.80ES-PS-LD-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 30.00 28.50 27.00 25.50 24.00ES-PS-LD-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ES-PS-LD-0400-4-220-60 4.00 mm 4 mm 22.0 mm 60 mm 25.00 23.75 22.50 21.25 20.00ES-PS-LD-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 30.00 28.50 27.00 25.50 24.00ES-PS-LD-0500-5-160-60 5.00 mm 5 mm 16.0 mm 60 mm 24.00 22.80 21.60 20.40 19.20ES-PS-LD-0600-6-220-60 6.00 mm 6 mm 22.0 mm 60 mm 27.00 25.65 24.30 22.95 21.60ES-PS-LD-0800-8-220-60 8.00 mm 8 mm 22.0 mm 60 mm 40.00 38.00 36.00 34.00 32.00ES-PS-LD-0800-8-320-70* 8.00 mm 8 mm 32.0 mm 70 mm 45.00 42.75 40.50 38.25 36.00ES-PS-LD-1000-10-300-75 10.00 mm 10 mm 30.0 mm 75 mm 50.00 47.50 45.00 42.50 40.00
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
3 new
tools
Carbide Tools | Diamond Tools 33
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Single Tooth C
utters
L1
D2 D3 αD1
V-slot cutters for aluminium composites
Description:An extra balanced tool which runs very smoothly; its top angle is 90°. With this milling cutter you can realize especially high rates of feed. For the uncoated tools, we offer a regrinding service at a price of € 12 per tool (our usual scales of discount are effective). On request we can produce this tool also with different bottom widths.
Coating:Also available with a super-hard carbon coating (SHC®). This diamond-like special coating distinguishes itself by a minimum friction value and extreme hardness. So the milling cutters get a great dry running performance and do not tend to clog too easily (see page 12).
Fields of application:This carbide tool is suitable for rectangular bendings in materials of up to 4 mm thickness (bottom width 3 mm).
For rectangular bendings in aluminium composites.
Dimensions and prices
Article no.
αTop
angle
D3Cutting edge
diameter
D1Bottom
width
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
ES-AV-090-1000-180-6-50* 90° 10.00 mm 1.8 mm 6 mm 50 mm 58.00 55.10 52.20 49.30ES-AV-090-1000-180-10-50* 90° 10.00 mm 1.8 mm 10 mm 50 mm 48.00 45.60 43.20 40.80ES-AV-090-1000-300-6-50* 90° 10.00 mm 3.0 mm 6 mm 50 mm 58.00 55.10 52.20 49.30ES-AV-090-1000-300-10-50* 90° 10.00 mm 3.0 mm 10 mm 50 mm 48.00 45.60 43.20 40.80
With SHC® coating, thickness 2.0 µm ± 0.2:ES-AV-090-1000-300-6-50-SHC* 90° 10.00 mm 3.0 mm 6 mm 50 mm 68.00 64.60 61.20 57.80ES-AV-090-1000-300-10-50-SHC* 90° 10.00 mm 3.0 mm 10 mm 50 mm 58.00 55.10 52.20 49.30
* new tool in this printed issue | * new tool in this PDF updateAsk for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
The bottom width (D1) of this milling cutter is 1.8 or 3 mm. It determines the later bending radius (r). Please note that there has to remain a rest of 0.6 to 0.8 mm of the plate which must not be milled.
Practical Tip
rr = 2 – 3 mm
0,6
– 0
,8 m
m
D3∢α
D1
regr
inda
ble
Alu Compo-
sites
New
Carbide Tools | Diamond Tools34
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Double Tooth CuttersMore than 150 tools for materials of medium hardness. Different kinds of radius cutters and torus cutters for mould making complete this product range.
Varius® cutters
Cutters with polished flute
Cutters with fishtail
HSC cutters
Cutters for aluminium
Cutters for aluminium profiles
Cutters for stainless steel
Cutters for wood
Cutters with face radius
Cutters with torus and undercut
Cutters with face radius and undercut
Rub out cutters
Free delivery at shop.vhf.de
L1
D2 D1
L2
Non-ferr.Metals
Ferrous Metals
Double tooth cutters Varius®
Description:This cutter of our own brand Varius® has two teeth and is made of finest grain carbide. It has a 30° spiral flute All tools with a cutting edge diameter from 5 mm have an edge chamfer.
Coating:All tools are TINALOX® SN² coated (see page 12) with a thickness of 3.0 µm ± 1.0.
Fields of application:For milling hard sorts of aluminium (Rm > 300 N/mm2) which are usually short-chipping, hard bronze alloys, zinc, brass, construction or cementation steel.
If you machine steel and other ferrous metals with these tools, please use only an appropriate lubricant for cool-ing, e. g. AquaTec®, WST 20 or the cutting oil spray Al-pha 93 (see page 121).
All-round double tooth cutters of finest grain carbide.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ZS-SC-0020-3-006-40 0.20 mm 3 mm 0.6 mm 40 mm 25.00 23.75 22.50 21.25 20.00ZS-SC-0050-3-015-40 0.50 mm 3 mm 1.5 mm 40 mm 21.00 19.95 18.90 17.85 16.80ZS-SC-0100-3-020-40* 1.00 mm 3 mm 2.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0100-3-030-40 1.00 mm 3 mm 3.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0150-3-045-40 1.50 mm 3 mm 4.5 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0200-3-060-40 2.00 mm 3 mm 6.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0200-3-090-40 2.00 mm 3 mm 9.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0200-6-070-50 2.00 mm 6 mm 7.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ZS-SC-0250-3-050-40* 2.50 mm 3 mm 5.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0250-3-075-40 2.50 mm 3 mm 7.5 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0300-3-090-40 3.00 mm 3 mm 9.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0300-3-120-40 3.00 mm 3 mm 12.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0300-6-070-50 3.00 mm 6 mm 7.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ZS-SC-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60ZS-SC-0400-6-080-50 4.00 mm 6 mm 8.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80
With edge chamfer 0.20 mm x 45°:ZS-SC-0500-6-100-50 5.00 mm 6 mm 10.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ZS-SC-0500-6-150-50 5.00 mm 6 mm 15.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ZS-SC-0600-6-120-50 6.00 mm 6 mm 12.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ZS-SC-0600-6-180-60 6.00 mm 6 mm 18.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60ZS-SC-0800-8-120-50 8.00 mm 8 mm 12.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ZS-SC-0800-8-220-60 8.00 mm 8 mm 22.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20ZS-SC-1000-10-120-50 10.00 mm 10 mm 12.0 mm 50 mm 34.00 32.30 30.60 28.90 27.20ZS-SC-1000-10-220-75 10.00 mm 10 mm 22.0 mm 75 mm 39.00 37.05 35.10 33.15 31.20ZS-SC-1000-10-280-75* 10.00 mm 10 mm 28.0 mm 75 mm 41.00 38.95 36.90 34.85 32.80ZS-SC-1200-12-220-75 12.00 mm 12 mm 22.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
3new
tools
Carbide Tools | Diamond Tools36
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
oubl
e To
oth
Cut
ters
L1
D2 D1
L2
Double tooth cutters with polished flute
Description:This milling cutter has a 25° spiral flute and a radial re-lief grinding. It runs very smoothly due to its two cutting edges which are ground extremely sharply and have a high-end finishing.
Coating:Some tools are available with the diamond coating CCDia® MultiSpeed Thin (see page 13).
Fields of application:Machining of soft wood and all kinds of thermoplas-tics. The coated tools are especially suitable for MDF, laminates, hard wood and aluminium.
Two extremely sharp cutting edges, high-end finished.
PlasticsRigid Foam
Wood
Dimensions and prices New
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.15 mm x 45°:ZS-PS-0300-3-120-50* 3.00 mm 3 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-PS-0300-3-120-0250-60* 3.00 mm 3 mm 12.0 mm 25.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ZS-PS-0400-4-140-50* 4.00 mm 4 mm 14.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ZS-PS-0400-4-140-0250-60* 4.00 mm 4 mm 14.0 mm 25.0 mm 60 mm 25.00 23.75 22.50 21.25 20.00ZS-PS-0600-6-140-50* 6.00 mm 6 mm 14.0 mm 50 mm 26.00 24.70 23.40 22.10 20.80ZS-PS-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20ZS-PS-0600-6-220-0350-70* 6.00 mm 6 mm 22.0 mm 35.0 mm 60 mm 33.00 31.35 29.70 28.05 26.40
With edge chamfer 0.25 mm x 45°:ZS-PS-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 39.00 37.05 35.10 33.15 31.20ZS-PS-0800-8-220-0350-70* 8.00 mm 8 mm 22.0 mm 35.0 mm 70 mm 43.00 40.85 38.70 36.55 34.40ZS-PS-1000-10-220-60* 10.00 mm 10 mm 22.0 mm 60 mm 49.00 46.55 44.10 41.65 39.20ZS-PS-1000-10-220-0350-70* 10.00 mm 10 mm 22.0 mm 35.0 mm 70 mm 53.00 50.35 47.70 45.05 42.40
With CCDia® MultiSpeed Thin, thickness 3.0 µm ± 1.0:1
ZS-PS-0300-3-120-50-MST* 3.00 mm 3 mm 12.0 mm 50 mm 33.00 31.35 29.70 28.05 26.40ZS-PS-0400-4-140-50-MST* 4.00 mm 4 mm 14.0 mm 50 mm 43.00 40.85 38.70 36.55 34.40ZS-PS-0600-6-140-50-MST* 6.00 mm 6 mm 14.0 mm 50 mm 53.00 50.35 47.70 45.05 42.40
* new tool in this printed issue1 as the diamond layer is an electrical isolator, these tools are not suitable for a measurement with the automatic z adjustment.Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Non-ferr.Metals
Carbide Tools | Diamond Tools 37
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Double Tooth
Cutters
L1
D2 D1
L2
Non-ferr.Metals
PlasticsRigid Foam
WoodCompo-
sitesPCBs
Double tooth cutters with fishtail
Description:Due to its fishtail grinding, this double tooth cutter can immerse even into hard materials quite easily. All tools with a shank diameter from 4 mm have a four area grinding at the tip instead of a two area grinding. The lead angle of the spiral flute is always 30°.Instead of a 3 mm shank you can also get a 1/8 inch shank on request.
Fields of application:A versatile double tooth cutter with an almost unbeat-able cost/performance ratio for milling soft non-ferrous metals, plastics, wood and composite materials. On top of that it convinces with a long endurance and clear-cut results.
Stop ring:Tools with 3 mm shank are equipped with a green stop ring, distance from tool tip to back of ring: 21 mm; on request also available without stop ring.
Universally applicable and a sensational bargain.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ZS-FS-0030-3-015-38 0.30 mm 3 mm 1.5 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0040-3-020-38 0.40 mm 3 mm 2.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0050-3-030-38 0.50 mm 3 mm 3.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0060-3-030-38 0.60 mm 3 mm 3.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0080-3-040-38 0.80 mm 3 mm 4.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0100-3-050-38 1.00 mm 3 mm 5.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0120-3-050-38 1.20 mm 3 mm 5.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0140-3-060-38 1.40 mm 3 mm 6.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0150-3-060-38 1.50 mm 3 mm 6.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0160-3-060-38 1.60 mm 3 mm 6.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0200-3-090-38 2.00 mm 3 mm 9.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0240-3-100-38 2.40 mm 3 mm 10.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60ZS-FS-0300-3-120-38 3.00 mm 3 mm 12.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60
With four area grinding:ZS-FS-0300-6-120-50 3.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60ZS-FS-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 14.00 13.30 12.60 11.90 11.20ZS-FS-0400-4-220-60 4.00 mm 4 mm 22.0 mm 60 mm 17.00 16.15 15.30 14.45 13.60ZS-FS-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60ZS-FS-0400-6-220-60 4.00 mm 6 mm 22.0 mm 60 mm 20.00 19.00 18.00 17.00 16.00ZS-FS-0500-6-120-50 5.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60ZS-FS-0600-6-120-50 6.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60ZS-FS-0600-6-220-60 6.00 mm 6 mm 22.0 mm 60 mm 20.00 19.00 18.00 17.00 16.00ZS-FS-0600-6-320-70 6.00 mm 6 mm 32.0 mm 70 mm 23.00 21.85 20.70 19.55 18.40ZS-FS-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 24.00 22.80 21.60 20.40 19.20ZS-FS-0800-8-320-75* 8.00 mm 8 mm 32.0 mm 75 mm 28.00 26.60 25.20 23.80 22.40
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
2new
tools
Carbide Tools | Diamond Tools38
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
oubl
e To
oth
Cut
ters
L1
D2 D1
L2
Non-ferr.Metals
PlasticsRigid Foam
Wood
HSC double tooth cuttersDescription:Due to its especially steep spiral flute (15°), the chips will be removed very quickly. This enables consider-ably higher rates of feed. The softer tractive force at the workpiece facilitates an improved holding force on vacuum tables. Furthermore, the tool has a polished flute which minimizes the risk of clogging when milling plastics.
Fields of application:For high-speed cutting of wood, plastics and non-fer-rous metals.
Practical tip:You can use this tool especially for quick roughing.
Extra steep spiral flute for high-speed cutting.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ZS-HSC-0150-3-045-40 1.50 mm 3 mm 4.5 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-HSC-0200-3-060-40 2.00 mm 3 mm 6.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-HSC-0200-3-090-40* 2.00 mm 3 mm 9.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-HSC-0200-6-060-50 2.00 mm 6 mm 6.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-HSC-0200-6-090-50* 2.00 mm 6 mm 9.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ZS-HSC-0300-3-090-40 3.00 mm 3 mm 9.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-HSC-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-HSC-0300-6-090-50 3.00 mm 6 mm 9.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-HSC-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60ZS-HSC-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 16.00 15.20 14.40 13.60 12.80ZS-HSC-0400-6-120-60 4.00 mm 6 mm 12.0 mm 60 mm 20.00 19.00 18.00 17.00 16.00ZS-HSC-0500-6-150-50 5.00 mm 6 mm 15.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-HSC-0600-6-120-50 6.00 mm 6 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-HSC-0600-6-180-60 6.00 mm 6 mm 18.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60ZS-HSC-0800-8-250-75 8.00 mm 8 mm 25.0 mm 75 mm 30.00 28.50 27.00 25.50 24.00
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
4new
tools
Carbide Tools | Diamond Tools 39
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Double Tooth
Cutters
L1
D2 D1
L2
Non-ferr.Metals
Double tooth cutters for aluminium
Description:With its 45° spiral flute, this tool creates especially smooth edges of cut. Some diameters have an addi-tional undercut.
Coating:Many diameters are available with the high performance coating AluSpeed® (see page 11).
Fields of application:Special milling cutter for aluminium and other non-ferrous metals.
Practical tip:This tool is ideal for trimming edges and for finishing. If you want to mill slots, please take care for a sufficient cooling.
Specialist for non-ferrous metals with 45° spiral flute.
Dimensions and prices 9new
tools
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ZS-AL-0100-3-030-40 1.00 mm 3 mm 3.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-AL-0100-3-030-0050-40* 1.00 mm 3 mm 3.0 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-AL-0130-3-039-40* 1.30 mm 3 mm 3.9 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-AL-0150-3-045-40 1.50 mm 3 mm 4.5 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-AL-0150-3-045-0075-40* 1.50 mm 3 mm 4.5 mm 7.5 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-AL-0200-3-060-40 2.00 mm 3 mm 6.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-AL-0200-3-060-0100-40* 2.00 mm 3 mm 6.0 mm 10.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-AL-0200-6-060-50 2.00 mm 6 mm 6.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0250-3-075-40* 2.50 mm 3 mm 7.5 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-AL-0250-3-075-0125-40* 2.50 mm 3 mm 7.5 mm 12.5 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-AL-0300-3-090-40 3.00 mm 3 mm 9.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80ZS-AL-0300-6-090-50 3.00 mm 6 mm 9.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 16.00 15.20 14.40 13.60 12.80ZS-AL-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0500-6-150-50 5.00 mm 6 mm 15.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0600-6-120-50 6.00 mm 6 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0600-6-180-60 6.00 mm 6 mm 18.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60ZS-AL-0800-8-140-50* 8.00 mm 8 mm 14.0 mm 50 mm 26.00 24.70 23.40 22.10 20.80ZS-AL-0800-8-250-75 8.00 mm 8 mm 25.0 mm 75 mm 30.00 28.50 27.00 25.50 24.00With AluSpeed® coating, layer thickness 2.0 µm ± 0.7:ZS-AL-0100-3-030-40-AS* 1.00 mm 3 mm 3.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0200-6-060-50-AS 2.00 mm 6 mm 6.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ZS-AL-0300-3-090-40-AS 3.00 mm 3 mm 9.0 mm 40 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0300-6-090-50-AS 3.00 mm 6 mm 9.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ZS-AL-0400-4-120-50-AS 4.00 mm 4 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00ZS-AL-0400-6-120-50-AS 4.00 mm 6 mm 12.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ZS-AL-0500-6-150-50-AS 5.00 mm 6 mm 15.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ZS-AL-0600-6-120-50-AS 6.00 mm 6 mm 12.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20ZS-AL-0600-6-180-60-AS 6.00 mm 6 mm 18.0 mm 60 mm 26.00 24.70 23.40 22.10 20.80ZS-AL-0800-8-140-50-AS* 8.00 mm 8 mm 14.0 mm 50 mm 33.00 31.35 29.70 28.05 26.40ZS-AL-0800-8-250-75-AS 8.00 mm 8 mm 25.0 mm 75 mm 38.00 36.10 34.20 32.30 30.40
* new tool in this printed issue
Carbide Tools | Diamond Tools40
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
oubl
e To
oth
Cut
ters
L1
D2 D1L2
L3
Non-ferr.Metals
Double tooth cutters for aluminium profiles
Description:The tool has very good drilling and immersion fea-tures and facilitates due to its short cutting edge high rates of feed. Thanks to finest polished cutting edges and flutes (30° spiral flute), it is nearly impossible that chips may adhere. Also composites of aluminium and plastics can be milled without burrs. An edge chamfer reduces the abrasion.
Fields of application:Due to its great total length and its long undercut, this tool type is optimally suitable for milling aluminium pro-files, especially for window and door making.
Please note: We are about to extend the range of this tool type by additional diameters from 6 mm on. Please check the vhf shop regularly to see all currently offered tools.
The specialist for aluminium profiles.
Dimensions
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.20 mm x 45°ZS-AP-0600-6-220-70* 6.00 mm 6 mm 22.0 mm 70 mm 28.00 26.60 25.20 23.80 22.40ZS-AP-0800-8-120-0550-85* 8.00 mm 8 mm 12.0 mm 55.0 mm 85 mm 38.00 36.10 34.20 32.30 30.40ZS-AP-0800-8-220-70* 8.00 mm 8 mm 22.0 mm 70 mm 38.00 36.10 34.20 32.30 30.40
With edge chamfer 0.30 mm x 45°ZS-AP-1000-10-140-0600-100* 10.00 mm 10 mm 14.0 mm 60.0 mm 100 mm 48.00 45.60 43.20 40.80 38.40ZS-AP-1000-10-140-0800-120* 10.00 mm 10 mm 14.0 mm 80.0 mm 120 mm 53.00 50.35 47.70 45.05 42.40ZS-AP-1000-10-220-70* 10.00 mm 10 mm 22.0 mm 70 mm 48.00 45.60 43.20 40.80 38.40ZS-AP-1200-12-160-0600-100* 12.00 mm 12 mm 16.0 mm 60.0 mm 100 mm 58.00 55.10 52.20 49.30 46.40ZS-AP-1200-12-220-70* 12.00 mm 12 mm 22.0 mm 70 mm 58.00 55.10 52.20 49.30 46.40
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
Carbide Tools | Diamond Tools 41
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Double Tooth
Cutters
L1
D2 D1L2
L3
Ferrous Metals
Double tooth cutters for stainless steel
Description:This torus cutter has an edge radius. Thus its wear re-sistance is increased and you will receive a very good surface quality. Its extra short cutting edge facilitates a high stiffness; the additional undercut which has the same length as the cutting edge enables also deeper slots to be milled. The lead of the spiral flute is 30°.
Coating:This tool is coated with a TINALOX® SN² thin layer coat-ing (see page 12) in a layer thickness 1.5 µm ± 0.5.
Fields of application:This cutter is suitable for machining steel and stainless steel; ideal for instance for making cutting dies or bigger engravings.
Please use only an appropriate lubricant for cooling, e. g. AquaTec®, WST 20 or the cutting oil spray Alpha 93 (see page 121).
Torus cutters with extra short cutting edge.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge radius 0.10 mm:ZS-ED-0090-3-009-0018-40* 0.90 mm 3 mm 0.9 mm 1.8 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0100-3-010-0020-40* 1.00 mm 3 mm 1.0 mm 2.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0110-3-011-0022-40* 1.10 mm 3 mm 1.1 mm 2.2 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0120-3-012-0024-40* 1.20 mm 3 mm 1.2 mm 2.4 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0130-3-013-0026-40* 1.30 mm 3 mm 1.3 mm 2.6 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0140-3-014-0028-40* 1.40 mm 3 mm 1.4 mm 2.8 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0150-3-015-0030-40* 1.50 mm 3 mm 1.5 mm 3.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40
With edge radius 0.20 mm:ZS-ED-0160-3-016-0032-40* 1.60 mm 3 mm 1.6 mm 3.2 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0170-3-017-0034-40* 1.70 mm 3 mm 1.7 mm 3.4 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0180-3-018-0036-40* 1.80 mm 3 mm 1.8 mm 3.6 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0190-3-019-0038-40* 1.90 mm 3 mm 1.9 mm 3.8 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0200-3-020-0040-40* 2.00 mm 3 mm 2.0 mm 4.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-ED-0250-3-025-0050-40* 2.50 mm 3 mm 2.5 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40
With edge radius 0.25 mm:ZS-ED-0300-3-030-0060-40* 3.00 mm 3 mm 3.0 mm 6.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
Carbide Tools | Diamond Tools42
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
oubl
e To
oth
Cut
ters
L1
D2 D1
L2
Wood
Double tooth cutters for wood
Description:This nearly straightly slotted tool (spiral of 1°) exerts only low drag forces on the workpiece and so effectively prevents a fraying of the edges of cut. The geometry of the tool tip is optimised for immersing quickly into the material. All of these milling cutters have an SHC® coat-ing which consists of super-hard carbon (see page 12) with a layer thickness of 2.0 µm ± 0.2.
Fields of application:Special tool for wood and all kinds of laminate.
No fraying of the edges due to straightly slotted flutes.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ZS-WO-0200-3-100-40* 2.00 mm 3 mm 10.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ZS-WO-0300-3-120-40 3.00 mm 3 mm 12.0 mm 40 mm 21.00 19.95 18.90 17.85 16.80ZS-WO-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ZS-WO-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80ZS-WO-0400-4-220-60 4.00 mm 4 mm 22.0 mm 60 mm 25.00 23.75 22.50 21.25 20.00ZS-WO-0400-6-120-50 4.00 mm 6 mm 12.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ZS-WO-0500-6-120-50 5.00 mm 6 mm 12.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ZS-WO-0600-6-120-50 6.00 mm 6 mm 12.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ZS-WO-0600-6-220-60 6.00 mm 6 mm 22.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20ZS-WO-0600-6-320-70 6.00 mm 6 mm 32.0 mm 70 mm 33.00 31.35 29.70 28.05 26.40ZS-WO-0800-8-220-60 8.00 mm 8 mm 22.0 mm 60 mm 37.00 35.15 33.30 31.45 29.60ZS-WO-0800-8-320-75 8.00 mm 8 mm 32.0 mm 75 mm 39.00 37.05 35.10 33.15 31.20ZS-WO-0800-8-420-85* 8.00 mm 8 mm 42.0 mm 85 mm 44.00 41.80 39.60 37.40 35.20ZS-WO-1000-10-320-75* 10.00 mm 10 mm 32.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
4new
tools
Carbide Tools | Diamond Tools 43
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Double Tooth
Cutters
L1
D2 D1
L2
Non-ferr.Metals
PlasticsRigid Foam
Wood
Double tooth cutters with face radius
Description:This milling cutter has two cutting edges with a spiral flute of 30° and is made of finest grain carbide. The tip of the tool is semi-circular rounded.
Fields of application:Due to its face radius, this tool is specially intended for model, tool and mould making. It can be used for ma-chining aluminium, zinc, brass, wood, acrylic glass and plastics.
These cutters are optionally available with an SHC® or TINALOX® SN2 coating for working on materials like GRP composites, carbon fibre reinforced plastics, cast iron, epoxy resin or harder sorts of metals (see page 12).
Double tooth cutters with face radius for mould making.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ZS-SCR-0100-3-050-40 1.00 mm 3 mm 5.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-SCR-0150-3-060-40 1.50 mm 3 mm 6.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-SCR-0200-3-090-40 2.00 mm 3 mm 9.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-SCR-0250-3-100-40* 2.50 mm 3 mm 10.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-SCR-0300-3-120-40 3.00 mm 3 mm 12.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40ZS-SCR-0300-3-250-60 3.00 mm 3 mm 25.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ZS-SCR-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40ZS-SCR-0400-4-250-60 4.00 mm 4 mm 25.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40ZS-SCR-0600-6-160-50 6.00 mm 6 mm 16.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00ZS-SCR-0600-6-300-70 6.00 mm 6 mm 30.0 mm 70 mm 35.00 33.25 31.50 29.75 28.00ZS-SCR-0800-8-200-60 8.00 mm 8 mm 20.0 mm 60 mm 35.00 33.25 31.50 29.75 28.00ZS-SCR-0800-8-350-75 8.00 mm 8 mm 35.0 mm 75 mm 45.00 42.75 40.50 38.25 36.00ZS-SCR-1000-10-220-75 10.00 mm 10 mm 22.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20ZS-SCR-1000-10-450-100 10.00 mm 10 mm 45.0 mm 100 mm 59.00 56.05 53.10 50.15 47.20ZS-SCR-1200-12-220-75 12.00 mm 12 mm 22.0 mm 75 mm 69.00 65.55 62.10 58.65 55.20ZS-SCR-1200-12-450-100 12.00 mm 12 mm 45.0 mm 100 mm 79.00 75.05 71.10 67.15 63.20
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
1new
tool
Carbide Tools | Diamond Tools44
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
oubl
e To
oth
Cut
ters
L1
D2 D1L2
L3
Non-ferr.Metals
PlasticsCompo-
sites
Double tooth cutters with torus and undercut
Description:Together with the double tooth cutter with face radius and undercut, this tool makes up an ideally matching mould making duo. With its torus grinding, this mill-ing cutter is the roughing specialist – i. e. for removing larger volumes of material. The edge radius at the end of the cutting edges (torus) ensures a greater resistance to wear. The rather flat angle of its spiral flute of 40° facilitates a smooth running and a good distribution of the cutting force. An especially long undercut of the shank enables a machining of the workpieces without interfering contour. Finally, a polished flute and espe-cially sharp cutting edges ensure perfect surfaces.
Fields of application:This tool is suitable for machining all kinds of non-ferrous metals, wood, plastics and titan. If you want to machine fibre-reinforced plastics (GRP/CRP), please ask us for the type with SHC® coating (see page 12).
A roughing specialist due to its torus grinding.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting
edge length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge radius 0.50 mm:ZS-T-0300-6-060-0500-100* 3.00 mm 6 mm 6.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20ZS-T-0400-6-080-0500-100* 4.00 mm 6 mm 8.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20ZS-T-0500-6-100-0500-100* 5.00 mm 6 mm 10.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20
With edge radius 1.00 mm:ZS-T-0600-6-120-0500-100* 6.00 mm 6 mm 12.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20ZS-T-0800-8-160-0500-100* 8.00 mm 8 mm 16.0 mm 50.0 mm 100 mm 44.00 41.80 39.60 37.40 35.20
With edge radius 1.50 mm:ZS-T-1000-10-200-0700-120* 10.00 mm 10 mm 20.0 mm 70.0 mm 120 mm 59.00 56.05 53.10 50.15 47.20
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
WoodRigid Foam
Carbide Tools | Diamond Tools 45
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Double Tooth
Cutters
L3
L1
D2 D1L2
Non-ferr.Metals
PlasticsCompo-
sites
Double tooth cutters with face radius and undercut
Description:Together with the double tooth cutter with torus and undercut, this tool makes up an ideally matching mould making duo. With its semi-circular face radius, this tool is a specialist for finishing – i. e. the final fine machin-ing after the roughing process. The rather flat angle of its spiral flute of 40° facilitates a smooth running and a good distribution of the cutting force. An especially long undercut of the shank enables a machining of the workpieces without interfering contour. Finally, a pol-ished flute and especially sharp cutting edges ensure perfect surfaces.
Fields of application:This tool is suitable for machining all kinds of non-ferrous metals, wood, plastics and titan. If you want to machine fibre-reinforced plastics (GRP/CRP), please ask us for the type with SHC® coating (see page 12).
An ideal finishing tool with face radius.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting
edge length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
ZS-R-0300-6-060-0500-100* 3.00 mm 6 mm 6.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20ZS-R-0400-6-080-0500-100* 4.00 mm 6 mm 8.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20ZS-R-0500-6-100-0500-100* 5.00 mm 6 mm 10.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20ZS-R-0600-6-120-0500-100* 6.00 mm 6 mm 12.0 mm 50.0 mm 100 mm 34.00 32.30 30.60 28.90 27.20ZS-R-0800-8-160-0500-100* 8.00 mm 8 mm 16.0 mm 50.0 mm 100 mm 44.00 41.80 39.60 37.40 35.20ZS-R-1000-10-200-0700-120* 10.00 mm 10 mm 20.0 mm 70.0 mm 120 mm 59.00 56.05 53.10 50.15 47.20
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
WoodRigid Foam
Carbide Tools | Diamond Tools46
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
oubl
e To
oth
Cut
ters
L1
D2 D1
L2
Non-ferr.Metals
PlasticsCompo-
sitesPCBs
Rub out cuttersDescription:The shortened cutting edge of this tool with a 30° spi-ral reduces the risk of fracture; with its fishtail grind-ing it is very sharp and straight. So it becomes quite easy to dip even into harder sorts of materials. An optimised four area grinding of the tip enables very plane surfaces. This tool is also well suitable for engraving without work-piece levelling.
Fields of application:You can use this tool especially for removing larger copper areas from printed circuit boards, but also for working on plastics and non-ferrous metals.
Special features:High rates of feed become possible due to a short cutting edge; long endurance.
Stop ring:All cutters are equipped with a blue stop ring, distance from tool tip to back of ring: 15 mm; on request also available without stop ring.
Cutters with extra short cutting edge and fishtail.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
RO-0050-3-015-30 0.50 mm 3 mm 1.5 mm 30 mm 10.00 9.50 9.00 8.50 8.00RO-0100-3-025-30 1.00 mm 3 mm 2.5 mm 30 mm 10.00 9.50 9.00 8.50 8.00RO-0200-3-045-30 2.00 mm 3 mm 4.5 mm 30 mm 10.00 9.50 9.00 8.50 8.00RO-0300-3-065-30* 3.00 mm 3 mm 6.5 mm 30 mm 10.00 9.50 9.00 8.50 8.00
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
1new
tool
Carbide Tools | Diamond Tools 47
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Double Tooth
Cutters
Carbide Tools | Diamond Tools48
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Triple Tooth CuttersIn addition to universal tools we offer – for an especially efficient machining – extra long triple tooth cutters for foam and a triple tooth cutters for stainless steel with a very short cut-ting edge.
Varius® cutters
Cutters for foam
Cutters for stainless steel
Free delivery at shop.vhf.de
L1
D2 D1
L2
Non-ferr.Metals
Ferrous Metals
Triple tooth cutters Varius®
Description:These triple tooth cutters of our own brand Varius® are made of finest grain carbide and have a 30° spiral flute with a centre cut. They already have a TiAlN coating for a longer endurance. All tools with a cutting edge dia-meter from 5 mm have an edge chamfer of 0.2 mm x 45°.
Coating:All tools are TINALOX® SN² coated (see page 12) with a thickness of 3.0 µm ± 1.0.
Fields of application:These triple tooth cutters are especially suitable for mill-ing tool steel, grey cast iron, cast steel, malleable cast iron and brass.
If you machine steel and other ferrous metals with these tools, please use only an appropriate lubricant for cool-ing, e. g. AquaTec®, WST 20 or the cutting oil spray Al-pha 93 (see page 121).
All-round triple tooth cutter of finest grain carbide.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
DS-SC-0100-3-030-40 1.00 mm 3 mm 3.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0150-3-045-40 1.50 mm 3 mm 4.5 mm 40 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0200-3-060-40 2.00 mm 3 mm 6.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0200-3-090-40 2.00 mm 3 mm 9.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0200-6-070-50 2.00 mm 6 mm 7.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80DS-SC-0250-3-075-40 2.50 mm 3 mm 7.5 mm 40 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0300-3-090-40 3.00 mm 3 mm 9.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0300-3-120-40 3.00 mm 3 mm 12.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0300-6-070-50 3.00 mm 6 mm 7.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80DS-SC-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60DS-SC-0400-6-080-50 4.00 mm 6 mm 8.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80
With edge chamfer 0.20 mm x 45°:DS-SC-0500-6-100-50 5.00 mm 6 mm 10.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80DS-SC-0500-6-150-50 5.00 mm 6 mm 15.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60DS-SC-0600-6-120-50 6.00 mm 6 mm 12.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80DS-SC-0600-6-180-60 6.00 mm 6 mm 18.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60DS-SC-0800-8-120-50 8.00 mm 8 mm 12.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00DS-SC-0800-8-220-60 8.00 mm 8 mm 22.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20DS-SC-1000-10-120-50 10.00 mm 10 mm 12.0 mm 50 mm 34.00 32.30 30.60 28.90 27.20DS-SC-1000-10-220-75 10.00 mm 10 mm 22.0 mm 75 mm 39.00 37.05 35.10 33.15 31.20DS-SC-1200-12-220-75 12.00 mm 12 mm 22.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Carbide Tools | Diamond Tools50
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esTr
iple
Too
th
Cut
ters
L1
D2 D1L2
L3
Foam
Triple tooth cutters for foam
Description:The cutting edge geometry of this tool is optimised for machining foam without fringing its vertical edges. The cutter’s tip is ground in a way that always smooth surfaces are achieved when you mill pockets. An espe-cially steep spiral flute with 15° enables an efficient clearance of chippings, also if deep slots are milled at high feed rates.
Fields of application:Specially suitable for machining foams of polyethylene (PE) and polyurethane (PUR). Ideal for milling inser-tions for suitcases etc.
Practical tip:Set a fill overlapping of at least 25 % for your milling works. If foam residues should remain on the cutting edge, we recommend to use a cleaner on acetone basis or to clean the tool in an ultrasonic bath.
Extra long and especially steep spiralled.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting
edge length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.10 mm x 45°:DS-FO-0300-3-120-0200-50* 3.00 mm 3 mm 12.0 mm 20.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20DS-FO-0300-3-200-0450-75* 3.00 mm 3 mm 20.0 mm 45.0 mm 75 mm 29.00 27.55 26.10 24.65 23.20DS-FO-0400-4-200-0450-75* 4.00 mm 4 mm 20.0 mm 45.0 mm 75 mm 34.00 32.30 30.60 28.90 27.20DS-FO-0400-4-300-0450-75* 4.00 mm 4 mm 30.0 mm 45.0 mm 75 mm 39.00 37.05 35.10 33.15 31.20DS-FO-0400-4-450-75* 4.00 mm 4 mm 45.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20DS-FO-0500-5-250-0450-75* 5.00 mm 5 mm 25.0 mm 45.0 mm 75 mm 39.00 37.05 35.10 33.15 31.20DS-FO-0600-6-250-0450-75* 6.00 mm 6 mm 25.0 mm 45.0 mm 75 mm 44.00 41.80 39.60 37.40 35.20DS-FO-0600-6-250-0700-100 6.00 mm 6 mm 25.0 mm 70.0 mm 100 mm 49.00 46.55 44.10 41.65 39.20DS-FO-0600-6-400-0700-100* 6.00 mm 6 mm 40.0 mm 70.0 mm 100 mm 54.00 51.30 48.60 45.90 43.20DS-FO-0800-8-250-0450-75* 8.00 mm 8 mm 25.0 mm 45.0 mm 75 mm 59.00 56.05 53.10 50.15 47.20DS-FO-0800-8-400-0700-100 8.00 mm 8 mm 40.0 mm 70.0 mm 100 mm 64.00 60.80 57.60 54.40 51.20DS-FO-0800-8-400-1150-150* 8.00 mm 8 mm 40.0 mm 115.0 mm 150 mm 69.00 65.55 62.10 58.65 55.20DS-FO-0800-8-550-0700-100* 8.00 mm 8 mm 55.0 mm 70.0 mm 100 mm 79.00 75.05 71.10 67.15 63.20DS-FO-1000-10-250-0450-75* 10.00 mm 10 mm 25.0 mm 45.0 mm 75 mm 69.00 65.55 62.10 58.65 55.20DS-FO-1000-10-400-0700-100* 10.00 mm 10 mm 40.0 mm 70.0 mm 100 mm 79.00 75.05 71.10 67.15 63.20DS-FO-1000-10-500-0850-120 10.00 mm 10 mm 50.0 mm 85.0 mm 120 mm 89.00 84.55 80.10 75.65 71.20DS-FO-1000-10-500-1150-150* 10.00 mm 10 mm 50.0 mm 115.0 mm 150 mm 99.00 94.05 89.10 84.15 79.20DS-FO-1200-12-500-0850-125 12.00 mm 12 mm 50.0 mm 85.0 mm 125 mm 134.00 127.30 120.60 113.90 107.20DS-FO-1200-12-500-1150-150* 12.00 mm 12 mm 50.0 mm 115.0 mm 150 mm 139.00 132.05 125.10 118.15 111.20
* new tool in this printed issue | * new tool in this PDF updateAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
15new
tools
Carbide Tools | Diamond Tools 51
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Triple Tooth C
utters
L1
D2 D1
L2
Ferrous Metals
Triple tooth cutters for stainless steel
Description:These milling cutters with three teeth have a very short cutting edge, the flute has an angle of 45° instead of the usual 30°. This reduces the abrasive force on the workpiece. The cutting force is being distributed more equally and the endurance of the tool will be prolonged.
Coating:All tools are HARDLOX® coated (see page 11) with a thickness of 3.0 µm ± 1.0.
Fields of application:This tool is especially suitable for milling steel and stain-less steel.
Please use only an appropriate lubricant for cooling, e. g. AquaTec®, WST 20 or the cutting oil spray Alpha 93 (see page 121).
Cutters with special geometry for stainless steel.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.075 mm x 45°DS-ED-0100-4-020-50 1.00 mm 4 mm 2.0 mm 50 mm 32.00 30.40 28.80 27.20 25.60DS-ED-0150-4-030-50 1.50 mm 4 mm 3.0 mm 50 mm 32.00 30.40 28.80 27.20 25.60DS-ED-0200-4-030-50 2.00 mm 4 mm 3.0 mm 50 mm 32.00 30.40 28.80 27.20 25.60
With edge chamfer 0.10 mm x 45°DS-ED-0250-4-030-50 2.50 mm 4 mm 3.0 mm 50 mm 32.00 30.40 28.80 27.20 25.60DS-ED-0300-6-045-57 3.00 mm 6 mm 4.5 mm 57 mm 34.00 32.30 30.60 28.90 27.20DS-ED-0400-6-060-57 4.00 mm 6 mm 6.0 mm 57 mm 34.00 32.30 30.60 28.90 27.20
With edge chamfer 0.15 mm x 45°DS-ED-0500-6-070-57 5.00 mm 6 mm 7.0 mm 57 mm 34.00 32.30 30.60 28.90 27.20DS-ED-0600-8-080-63 6.00 mm 8 mm 8.0 mm 63 mm 38.00 36.10 34.20 32.30 30.40
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Carbide Tools | Diamond Tools52
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esTr
iple
Too
th
Cut
ters
Four Tooth CuttersMilling cutters with four cutting edges are recommended for working on tempered steel, cast and other sorts of materials which are dif-ficult to machine. They are always hard coated.
Varius® cutters
Ratio cutters
Free delivery at shop.vhf.de
L1L2
D2 D1
Ferrous Metals
Four tooth cutters Varius®
Description:The four tooth cutters of our own brand Varius® are made of finest grain carbide. They have a 30° spiral flute and are centre cutting. All tools with a cutting edge diameter from 5 mm have an edge chamfer.
Coating:By default, all tools are TINALOX® SN² coated (see page 12). On top of that we offer some tools with the even harder HYPERLOX® coating (see page 12).
Fields of application:We recommend to use four tooth cutters for working on high-alloy steel and tempered steel, cast, titanium, nickel alloys, die steel and other materials which are hard to machine.
If you machine steel and other ferrous metals with these tools, please use only an appropriate lubricant for cool-ing, e. g. AquaTec®, WST 20 or the cutting oil spray Al-pha 93 (see page 121).
“Snappish”: four teeth for very hard materials.
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With TINALOX® SN² coating, layer thickness 3.0 µm ± 1.0:VS-SC-0020-3-006-40 0.20 mm 3 mm 0.6 mm 40 mm 25.00 23.75 22.50 21.25 20.00VS-SC-0050-3-015-40 0.50 mm 3 mm 1.5 mm 40 mm 21.00 19.95 18.90 17.85 16.80VS-SC-0100-3-030-40 1.00 mm 3 mm 3.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60VS-SC-0150-3-045-40 1.50 mm 3 mm 4.5 mm 40 mm 17.00 16.15 15.30 14.45 13.60VS-SC-0200-3-060-40 2.00 mm 3 mm 6.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60VS-SC-0200-3-090-40 2.00 mm 3 mm 9.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60VS-SC-0250-3-075-40 2.50 mm 3 mm 7.5 mm 40 mm 17.00 16.15 15.30 14.45 13.60VS-SC-0300-3-090-40 3.00 mm 3 mm 9.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60VS-SC-0300-3-120-40 3.00 mm 3 mm 12.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60VS-SC-0400-4-120-50 4.00 mm 4 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60Additionally with edge chamfer 0.20 mm x 45°:VS-SC-0500-6-150-50 5.00 mm 6 mm 15.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60VS-SC-0600-6-180-60 6.00 mm 6 mm 18.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60VS-SC-0800-8-200-60 8.00 mm 8 mm 20.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20VS-SC-1000-10-120-50 10.00 mm 10 mm 12.0 mm 50 mm 34.00 32.30 30.60 28.90 27.20VS-SC-1000-10-220-75 10.00 mm 10 mm 22.0 mm 75 mm 39.00 37.05 35.10 33.15 31.20VS-SC-1200-12-220-75 12.00 mm 12 mm 22.0 mm 75 mm 49.00 46.55 44.10 41.65 39.20
With HYPERLOX® coating, layer thickness 3.0 µm ± 1.0:VS-SC-0200-6-070-50-HL 2.00 mm 6 mm 7.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60 VS-SC-0300-6-070-50-HL 3.00 mm 6 mm 7.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60 VS-SC-0400-6-080-50-HL 4.00 mm 6 mm 8.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60 Additionally with edge chamfer 0.20 mm x 45°:VS-SC-0500-6-100-50-HL 5.00 mm 6 mm 10.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60 VS-SC-0600-6-120-50-HL 6.00 mm 6 mm 12.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60 VS-SC-0800-8-120-50-HL 8.00 mm 8 mm 12.0 mm 50 mm 26.00 24.70 23.40 22.10 20.80
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Dimensions and prices
Carbide Tools | Diamond Tools54
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esFo
ur T
ooth
C
utte
rs
L1
D2 D1
L2
L3
Ferrous Metals
Four tooth Ratio cuttersDescription:Centre-cutting four tooth cutters with different lead angles of the flutes of 35° and 38°. This asymmetry fa-cilitates a vibration-free running and counteracts the unwanted cork-screw effect. So you will achieve smooth edges of cut at high rates of feed.
Coating:All tools have a HPN1 coating (see page 11) with a layer thickness of 3.0 µm ± 1.0.
Fields of application:Suitable for machining harder workpieces like steel, cast iron, titanium and other materials which are hard to machine.
Please use only an appropriate lubricant for cooling, e. g. AquaTec®, WST 20 or the cutting oil spray Alpha 93 (see page 121).
Unequal lead angles of the flutes reduce vibrations.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.15 mm x 45°VS-RF-0400-6-110-0180-57 4,00 mm 6 mm 11,0 mm 18,0 mm 57 mm 25,00 23,75 22,50 21,25 20,00VS-RF-0500-6-130-0180-57 5,00 mm 6 mm 13,0 mm 18,0 mm 57 mm 25,00 23,75 22,50 21,25 20,00
With edge chamfer 0.20 mm x 45°VS-RF-0600-6-130-0210-57 6,00 mm 6 mm 13,0 mm 21,0 mm 57 mm 25,00 23,75 22,50 21,25 20,00
With edge chamfer 0.25 mm x 45°VS-RF-0800-8-190-0270-63 8,00 mm 8 mm 19,0 mm 27,0 mm 63 mm 35,00 33,25 31,50 29,75 28,00VS-RF-1000-10-220-0320-72 10,00 mm 10 mm 22,0 mm 32,0 mm 72 mm 50,00 47,50 45,00 42,50 40,00
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Carbide Tools | Diamond Tools 55
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Four Tooth C
utters
Carbide Tools | Diamond Tools56
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Roughing andFinishing CuttersThe interrupted cutting edge profile of the roughing cutters with diamond-shaped knurl-ing for quickly breaking the chips is characteris-tic for these kinds of tools. The especially short chips can be removed then quite quickly. So a maximum volume of chips can be removed at high rates of feed with these milling cutters. However, in most cases a finishing process with a separate tool is necessary.
We also offer a suitable finishing cutter with especially low-vibration running characteristics for processing copper.
Roughing cutters for copper
Roughing cutters for graphite
Finishing cutters for copper
Free delivery at shop.vhf.de
L1
D2 D1
L2
Roughing cutters for copper
Description:This centre-cutting tool with three cutting edges is made of a special carbide substrate. Its spiral flute has a variable torsion of 30 – 35°. This helps to avoid vibra-tions and enables a greater profile depth at higher cut-ting speeds. An additional edge chamfer reduces the wear and thus increases the endurance. The roughing toothing with its characteristic chip splitters effectively breaks the chips and allows to remove large amounts of material.
Fields of application:Roughing copper and other sorts of hard non-ferrous metals.
Special toothing for removing large amounts of material.
Abmessungen und PreiseDimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.15 mm x 45°SF-CU-DS-0300-6-080-57* 3.00 mm 6 mm 8.0 mm 57 mm 28.00 26.60 25.20 23.80 22.40
With edge chamfer 0.20 mm x 45°SF-CU-DS-0400-6-100-57* 4.00 mm 6 mm 10.0 mm 57 mm 28.00 26.60 25.20 23.80 22.40
With edge chamfer 0.25 mm x 45°SF-CU-DS-0500-6-130-57* 5.00 mm 6 mm 13.0 mm 57 mm 28.00 26.60 25.20 23.80 22.40
With edge chamfer 0.30 mm x 45°SF-CU-DS-0600-8-130-63* 6.00 mm 8 mm 13.0 mm 63 mm 34.00 32.30 30.60 28.90 27.20
With edge chamfer 0.40 mm x 45°SF-CU-DS-0800-8-160-63* 8.00 mm 8 mm 16.0 mm 63 mm 40.00 38.00 36.00 34.00 32.00
With edge chamfer 0.50 mm x 45°SF-CU-DS-1000-10-220-72* 10.00 mm 10 mm 22.0 mm 72 mm 52.00 49.40 46.80 44.20 41.60
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
Non-ferr.Metals
Carbide Tools | Diamond Tools58
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esRo
ughi
ng
Cut
ters
L2L1
D2 D1
L3
Roughing cutters for graphite
Description:Milling cutter with three cutting edges, from 10 mm diameter on with four cutting edges. The lead angle of the spiral flute is always 30°. The tool is centre-cutting and an additional edge chamfer reduces the wear and thus increases the endurance. The roughing toothing with its characteristic chip splitters effectively breaks the chips and allows to remove large amounts of ma-terial.
Coating:These milling cutters have an SHC® coating which con-sists of super-hard carbon (see page 12).
Fields of application:Roughing graphite.
Three or four cutting edges and additional coating.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting
edge length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.20 mm x 45°SF-G-DS-0400-4-100-0300-60* 4.00 mm 4 mm 10.0 mm 30.0 mm 60 mm 39.00 37.05 35.10 33.15 31.20
With edge chamfer 0.30 mm x 45°SF-G-DS-0600-6-130-0210-57* 6.00 mm 6 mm 13.0 mm 21.0 mm 57 mm 44.00 41.80 39.60 37.40 35.20
With edge chamfer 0.40 mm x 45°SF-G-DS-0800-8-190-0270-63* 8.00 mm 8 mm 19.0 mm 27.0 mm 63 mm 49.00 46.55 44.10 41.65 39.20
With edge chamfer 0.50 mm x 45°SF-G-VS-1000-10-220-0320-72* 10.00 mm 10 mm 22.0 mm 32.0 mm 72 mm 64.00 60.80 57.60 54.40 51.20
With edge chamfer 0.60 mm x 45°SF-G-VS-1200-12-260-0380-83* 12.00 mm 12 mm 26.0 mm 38.0 mm 83 mm 74.00 70.30 66.60 62.90 59.20
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
Graphite
Carbide Tools | Diamond Tools 59
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Roughing C
utters
L1
D2 D1
L2
Finishing cutters for copper
Description:This triple-toothed cutter has different spiral angles (39°/40°/ 41°) and a variable torsion. It is especially suit-able for machining long-chipping materials. Due to its reinforced face cutting edges and the symmetric cross grinding, this cutter has a improved drilling and ramp behaviour. The unequal partition (114°/120°/126°) and the micro supporting chamfer at its perimeter ensure a vibration-free running. An additional edge chamfer reduces the abrasion and thus increases the endur-ance. The polished cutting edges and chipping area fa-cilitate a high surface quality.
Fields of application:Grooving and finishing of copper, aluminium (alloys) as well as long-chipping plastics.
Abmessungen und PreiseDimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
With edge chamfer 0.10 mm x 45°SLF-CU-DS-0150-4-035-50* 1.50 mm 4 mm 3.5 mm 50 mm 22.00 20.90 19.80 18.70 17.60SLF-CU-DS-0200-4-045-50* 2.00 mm 4 mm 4.5 mm 50 mm 22.00 20.90 19.80 18.70 17.60
With edge chamfer 0.20 mm x 45°SLF-CU-DS-0300-6-080-57* 3.00 mm 6 mm 8.0 mm 57 mm 25.00 23.75 22.50 21.25 20.00SLF-CU-DS-0400-6-100-57* 4.00 mm 6 mm 10.0 mm 57 mm 25.00 23.75 22.50 21.25 20.00SLF-CU-DS-0500-6-130-57* 5.00 mm 6 mm 13.0 mm 57 mm 25.00 23.75 22.50 21.25 20.00SLF-CU-DS-0600-8-130-63* 6.00 mm 8 mm 13.0 mm 63 mm 32.00 30.40 28.80 27.20 25.60SLF-CU-DS-0800-8-160-63* 8.00 mm 8 mm 16.0 mm 63 mm 32.00 30.40 28.80 27.20 25.60SLF-CU-DS-1000-10-220-72* 10.00 mm 10 mm 22.0 mm 72 mm 45.00 42.75 40.50 38.25 36.00
* new tool in this printed issue | * new tool in this PDF updateAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Non-ferr.Metals
Different spiral angles for a smooth running.
New
Carbide Tools | Diamond Tools60
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esFi
nish
ing
Cut
ters
Composite CuttersWe offer a whole series of special milling cut-ters with cross cut, diamond or spiral toothing for highly abrasive materials like GRP/CRP or honeycomb plates.
Finely toothed cutters
Finely toothed cutters with chip breaker
Medium toothed cutters
Coarsely toothed cutters
Straightly slotted honeycomb cutters
Spiral-fluted honeycomb cutters
PCB outline cutters, diamond-toothed
PCB outline cutters, spiral-toothed
Free delivery at shop.vhf.de
L1
D2 D1
L2
Compo-sites
Finely toothed composite cutters
Description:Milling cutter with a fine-staggered tooth system of 10 to 14 micro-teeth rows. Due to its 30° right hand twist, the chips can be well removed, at the same time a tractive force is exerted on the workpiece. The tool has a double-tooth face grinding with four areas at its top.
It distinguishes itself by a high endurance with a very high edge holding ability; for burr-free milling with-out delamination of the layers. The fibres of the com-posite materials will be sheared off very accurately.
Fields of application:GRP/CRP materials (glass reinforced plastics and carbon fibre reinforced plastics) with a medium (30 – 60 %) to high fibre amount (> 60 %).
Extra fine tooth system for milling without delamination.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-F-0300-3-060-40* 3.00 mm 3 mm 6.0 mm 40 mm 10.50 9.98 9.45 8.93 8.40LK-F-0300-3-090-40* 3.00 mm 3 mm 9.0 mm 40 mm 11.00 10.45 9.90 9.35 8.80LK-F-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 11.50 10.93 10.35 9.78 9.20LK-F-0300-3-160-50* 3.00 mm 3 mm 16.0 mm 50 mm 12.00 11.40 10.80 10.20 9.60LK-F-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-F-0300-6-160-50* 3.00 mm 6 mm 16.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-F-0400-4-060-40* 4.00 mm 4 mm 6.0 mm 40 mm 12.00 11.40 10.80 10.20 9.60LK-F-0400-4-100-40* 4.00 mm 4 mm 10.0 mm 40 mm 13.00 12.35 11.70 11.05 10.40LK-F-0400-4-140-50* 4.00 mm 4 mm 14.0 mm 50 mm 14.00 13.30 12.60 11.90 11.20LK-F-0400-4-180-50* 4.00 mm 4 mm 18.0 mm 50 mm 15.00 14.25 13.50 12.75 12.00LK-F-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 16.00 15.20 14.40 13.60 12.80LK-F-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-F-0400-6-160-50* 4.00 mm 6 mm 16.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-F-0500-5-160-60* 5.00 mm 5 mm 16.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20LK-F-0500-6-140-50* 5.00 mm 6 mm 14.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-F-0500-6-220-60* 5.00 mm 6 mm 22.0 mm 60 mm 21.00 19.95 18.90 17.85 16.80LK-F-0600-6-140-50* 6.00 mm 6 mm 14.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00LK-F-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 23.50 22.33 21.15 19.98 18.80LK-F-0600-6-320-70* 6.00 mm 6 mm 32.0 mm 70 mm 27.00 25.65 24.30 22.95 21.60LK-F-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 34.00 32.30 30.60 28.90 27.20LK-F-0800-8-320-75* 8.00 mm 8 mm 32.0 mm 75 mm 38.00 36.10 34.20 32.30 30.40LK-F-1000-10-320-75* 10.00 mm 10 mm 32.0 mm 75 mm 46.00 43.70 41.40 39.10 36.80
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Wood
New
Carbide Tools | Diamond Tools62
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esC
ompo
site
C
utte
rs
L1
D2 D1
L2
Compo-sites
Finely toothed composite cutters with chip breaker
Description:Milling cutter with a fine-staggered tooth system of 10 to 14 micro-teeth rows and an integrated chip breaker flute. So long chips will be chopped and due to its 30° right hand twist, the chips can be well removed then; at the same time a tractive force is exerted on the workpiece. The tool has a double-tooth face grinding with four areas at its top. It distinguishes itself by a high endurance with a very high edge holding ability; for burr-free milling without delamination of the layers. The fibres of the composite materials will be sheared off very accurately.
Coating:Some tools have the extra hard diamond coating CCDia® FiberSpeed (see page 13).
Fields of application:GRP/CRP materials with a medium (30 – 60 %) to high fibre amount (> 60 %), rather long-chipping fibres and a light tendency to smearing.
Extra chip-breaker for improved chip removal.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-FSB-0300-3-060-40* 3.00 mm 3 mm 6.0 mm 40 mm 12.50 11.88 11.25 10.63 10.00LK-FSB-0300-3-090-40* 3.00 mm 3 mm 9.0 mm 40 mm 13.00 12.35 11.70 11.05 10.40LK-FSB-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 13.50 12.83 12.15 11.48 10.80LK-FSB-0300-3-160-50* 3.00 mm 3 mm 16.0 mm 50 mm 14.00 13.30 12.60 11.90 11.20LK-FSB-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00LK-FSB-0300-6-160-50* 3.00 mm 6 mm 16.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80LK-FSB-0400-4-060-40* 4.00 mm 4 mm 6.0 mm 40 mm 14.00 13.30 12.60 11.90 11.20LK-FSB-0400-4-100-40* 4.00 mm 4 mm 10.0 mm 40 mm 14.50 13.78 13.05 12.33 11.60LK-FSB-0400-4-140-50* 4.00 mm 4 mm 14.0 mm 50 mm 15.00 14.25 13.50 12.75 12.00LK-FSB-0400-4-180-50* 4.00 mm 4 mm 18.0 mm 50 mm 15.50 14.73 13.95 13.18 12.40LK-FSB-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 16.00 15.20 14.40 13.60 12.80LK-FSB-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00LK-FSB-0400-6-160-50* 4.00 mm 6 mm 16.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80LK-FSB-0500-5-160-60* 5.00 mm 5 mm 16.0 mm 60 mm 21.00 19.95 18.90 17.85 16.80LK-FSB-0500-6-140-50* 5.00 mm 6 mm 14.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80LK-FSB-0500-6-220-60* 5.00 mm 6 mm 22.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40LK-FSB-0600-6-140-50* 6.00 mm 6 mm 14.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00LK-FSB-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 27.00 25.65 24.30 22.95 21.60LK-FSB-0600-6-320-70* 6.00 mm 6 mm 32.0 mm 70 mm 29.00 27.55 26.10 24.65 23.20LK-FSB-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 36.00 34.20 32.40 30.60 28.80LK-FSB-0800-8-320-75* 8.00 mm 8 mm 32.0 mm 75 mm 38.00 36.10 34.20 32.30 30.40LK-FSB-1000-10-320-75* 10.00 mm 10 mm 32.0 mm 75 mm 48.00 45.60 43.20 40.80 38.40
With CCDia®FiberSpeed coating, layer thickness 9.0 µm ± 1.0:1
LK-FSB-0300-3-120-40-DIA* 3.00 mm 3 mm 12.0 mm 40 mm 33.00 31.35 29.70 28.05 26.40LK-FSB-0400-4-140-50-DIA* 4.00 mm 4 mm 14.0 mm 50 mm 48.00 45.60 43.20 40.80 38.40LK-FSB-0600-6-140-50-DIA* 6.00 mm 6 mm 14.0 mm 50 mm 68.00 64.60 61.20 57.80 54.40LK-FSB-0800-8-220-60-DIA* 8.00 mm 8 mm 22.0 mm 60 mm 98.00 93.10 88.20 83.30 78.40
* new tool in this printed issue1 as the diamond layer is an electrical isolator, these tools are not suitable for a measurement with the automatic z adjustment.Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Wood
New
Carbide Tools | Diamond Tools 63
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Com
posite C
utters
L1
D2 D1
L2
Compo-sites
Medium-toothed composite cutters
Description:Milling cutter with a medium-staggered tooth system of eight to twelve micro-teeth rows. Due to its 25° right hand twist, the chips can be well removed, at the same time a tractive force is exerted on the workpiece. The tool has a double-tooth face grinding with four areas at its top.
It distinguishes itself by a high endurance with a very high edge holding ability. The fibres of the composite materials will be sheared off very accurately.
Fields of application:GRP/CRP materials with a low (< 30 %) to medium fibre amount (30 – 60 %) and a high tendency to smearing. Also well suitable for pure glass and carbon fibre fabrics and for honeycomb plates.
For materials with high tendency to smearing.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-M-0300-3-060-40* 3.00 mm 3 mm 6.0 mm 40 mm 10.50 9.98 9.45 8.93 8.40LK-M-0300-3-090-40* 3.00 mm 3 mm 9.0 mm 40 mm 11.00 10.45 9.90 9.35 8.80LK-M-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 11.50 10.93 10.35 9.78 9.20LK-M-0300-3-160-50* 3.00 mm 3 mm 16.0 mm 50 mm 12.00 11.40 10.80 10.20 9.60LK-M-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-M-0300-6-160-50* 3.00 mm 6 mm 16.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-M-0400-4-060-40* 4.00 mm 4 mm 6.0 mm 40 mm 12.00 11.40 10.80 10.20 9.60LK-M-0400-4-100-40* 4.00 mm 4 mm 10.0 mm 40 mm 13.00 12.35 11.70 11.05 10.40LK-M-0400-4-140-50* 4.00 mm 4 mm 14.0 mm 50 mm 14.00 13.30 12.60 11.90 11.20LK-M-0400-4-180-50* 4.00 mm 4 mm 18.0 mm 50 mm 15.00 14.25 13.50 12.75 12.00LK-M-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 16.00 15.20 14.40 13.60 12.80LK-M-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-M-0400-6-160-50* 4.00 mm 6 mm 16.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-M-0500-5-160-60* 5.00 mm 5 mm 16.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20LK-M-0500-6-140-50* 5.00 mm 6 mm 14.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-M-0500-6-220-60* 5.00 mm 6 mm 22.0 mm 60 mm 21.00 19.95 18.90 17.85 16.80LK-M-0600-6-140-50* 6.00 mm 6 mm 14.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00LK-M-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 23.50 22.33 21.15 19.98 18.80LK-M-0600-6-320-70* 6.00 mm 6 mm 32.0 mm 70 mm 27.00 25.65 24.30 22.95 21.60LK-M-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 34.00 32.30 30.60 28.90 27.20LK-M-0800-8-320-75* 8.00 mm 8 mm 32.0 mm 75 mm 38.00 36.10 34.20 32.30 30.40LK-M-1000-10-320-75* 10.00 mm 10 mm 32.0 mm 75 mm 46.00 43.70 41.40 39.10 36.80
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Wood
New
Carbide Tools | Diamond Tools64
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esC
ompo
site
C
utte
rs
L1
D2 D1
L2
Compo-sites
Coarsely toothed composite cutters
Description:Milling cutter with a coarse-staggered tooth system of six to eight micro-teeth rows. Due to its 20° right hand twist, the chips can be well removed, at the same time a tractive force is exerted on the workpiece. The tool has a double-tooth face grinding with four areas at its top.
It distinguishes itself by a high endurance with a very high edge holding ability. The fibres of the composite materials will be sheared off accurately.
Fields of application:GRP/CRP materials with a low fibre amount (< 30 %). Also well suitable for semi-finished fibre matrix prod-ucts (BMC, SMC, GMT, LFT) and for foamed materials.
Coarse teeth for materials with low fibre amount.
Dimensions and prices
Wood
New
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-G-0300-3-060-40* 3.00 mm 3 mm 6.0 mm 40 mm 10.50 9.98 9.45 8.93 8.40LK-G-0300-3-090-40* 3.00 mm 3 mm 9.0 mm 40 mm 11.00 10.45 9.90 9.35 8.80LK-G-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 11.50 10.93 10.35 9.78 9.20LK-G-0300-3-160-50* 3.00 mm 3 mm 16.0 mm 50 mm 12.00 11.40 10.80 10.20 9.60LK-G-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-G-0300-6-160-50* 3.00 mm 6 mm 16.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-G-0400-4-060-40* 4.00 mm 4 mm 6.0 mm 40 mm 12.00 11.40 10.80 10.20 9.60LK-G-0400-4-100-40* 4.00 mm 4 mm 10.0 mm 40 mm 13.00 12.35 11.70 11.05 10.40LK-G-0400-4-140-50* 4.00 mm 4 mm 14.0 mm 50 mm 14.00 13.30 12.60 11.90 11.20LK-G-0400-4-180-50* 4.00 mm 4 mm 18.0 mm 50 mm 15.00 14.25 13.50 12.75 12.00LK-G-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 16.00 15.20 14.40 13.60 12.80LK-G-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-G-0400-6-160-50* 4.00 mm 6 mm 16.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-G-0500-5-160-60* 5.00 mm 5 mm 16.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20LK-G-0500-6-140-50* 5.00 mm 6 mm 14.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-G-0500-6-220-60* 5.00 mm 6 mm 22.0 mm 60 mm 21.00 19.95 18.90 17.85 16.80LK-G-0600-6-140-50* 6.00 mm 6 mm 14.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00LK-G-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 23.50 22.33 21.15 19.98 18.80LK-G-0600-6-320-70* 6.00 mm 6 mm 32.0 mm 70 mm 27.00 25.65 24.30 22.95 21.60LK-G-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 34.00 32.30 30.60 28.90 27.20LK-G-0800-8-320-75* 8.00 mm 8 mm 32.0 mm 75 mm 38.00 36.10 34.20 32.30 30.40LK-G-1000-10-320-75* 10.00 mm 10 mm 32.0 mm 75 mm 46.00 43.70 41.40 39.10 36.80
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Carbide Tools | Diamond Tools 65
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Com
posite C
utters
L1
D2 D1
L2
Compo-sites
Straightly slotted honeycomb cutters
Description:Five tooth cutter with opposed chip breakers. Due to its straight flute, the chips can be well removed and there are no tractive forces exerted on the workpiece. The tool has a five-tooth face-grinding at its top.
It distinguishes itself by a high endurance with a very high edge holding ability; for burr-free milling with-out delamination of the layers. The fibres of the com-posite materials will be sheared off very accurately, at the same there is a very good heat dissipation from the workpiece. Suitable for an increased chip removal vol-ume.
Fields of application:Ideal for honeycomb plates and also well suitable for ar-amid fibre reinforced plastics and GRP/CRP materials.
No tractive forces on the workpiece due to straight flute.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-HC-0300-3-060-40* 3.00 mm 3 mm 6.0 mm 40 mm 14.50 13.78 13.05 12.33 11.60LK-HC-0300-3-090-40* 3.00 mm 3 mm 9.0 mm 40 mm 15.00 14.25 13.50 12.75 12.00LK-HC-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 15.50 14.73 13.95 13.18 12.40LK-HC-0300-3-160-50* 3.00 mm 3 mm 16.0 mm 50 mm 16.00 15.20 14.40 13.60 12.80LK-HC-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60LK-HC-0300-6-160-50* 3.00 mm 6 mm 16.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40LK-HC-0400-4-060-40* 4.00 mm 4 mm 6.0 mm 40 mm 16.00 15.20 14.40 13.60 12.80LK-HC-0400-4-100-40* 4.00 mm 4 mm 10.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60LK-HC-0400-4-140-50* 4.00 mm 4 mm 14.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-HC-0400-4-180-50* 4.00 mm 4 mm 18.0 mm 50 mm 19.00 18.05 17.10 16.15 15.20LK-HC-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 20.00 19.00 18.00 17.00 16.00LK-HC-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 22.00 20.90 19.80 18.70 17.60LK-HC-0400-6-160-50* 4.00 mm 6 mm 16.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40LK-HC-0500-5-160-60* 5.00 mm 5 mm 16.0 mm 60 mm 23.00 21.85 20.70 19.55 18.40LK-HC-0500-6-140-50* 5.00 mm 6 mm 14.0 mm 50 mm 23.00 21.85 20.70 19.55 18.40LK-HC-0500-6-220-60* 5.00 mm 6 mm 22.0 mm 60 mm 25.00 23.75 22.50 21.25 20.00LK-HC-0600-6-140-50* 6.00 mm 6 mm 14.0 mm 50 mm 27.00 25.65 24.30 22.95 21.60LK-HC-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 29.00 27.55 26.10 24.65 23.20LK-HC-0600-6-320-70* 6.00 mm 6 mm 32.0 mm 70 mm 31.00 29.45 27.90 26.35 24.80LK-HC-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 38.00 36.10 34.20 32.30 30.40LK-HC-0800-8-320-75* 8.00 mm 8 mm 32.0 mm 75 mm 40.00 38.00 36.00 34.00 32.00LK-HC-1000-10-320-75* 10.00 mm 10 mm 32.0 mm 75 mm 50.00 47.50 45.00 42.50 40.00
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Wood
New
Carbide Tools | Diamond Tools66
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esC
ompo
site
C
utte
rs
L1
D2 D1
L2
Compo-sites
Spiral-fluted honeycomb cutters
Description:Six tooth cutter with opposed chip breakers. Due to its 10° right hand twist, the chips can be well removed, at the same time only a slight tractive force is exerted on the workpiece. The tool has a special triple-tooth face grinding at its top with one center-crossing tooth for an optimal immersion.
It distinguishes itself by a high endurance with a very high edge holding ability; for burr-free milling with-out delamination of the layers. The fibres of the com-posite materials will be sheared off very accurately, at the same there is a very good heat dissipation from the workpiece. Suitable for a maximum chip removal volume.
Fields of application:Ideal for honeycomb plates and also well suitable for ar-amid fibre reinforced plastics and GRP/CRP materials.
A six tooth cutter for maximum chip removal volume.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-HCS-0300-3-060-40* 3.00 mm 3 mm 6.0 mm 40 mm 16.50 15.68 14.85 14.03 13.20LK-HCS-0300-3-090-40* 3.00 mm 3 mm 9.0 mm 40 mm 17.00 16.15 15.30 14.45 13.60LK-HCS-0300-3-120-40* 3.00 mm 3 mm 12.0 mm 40 mm 17.50 16.63 15.75 14.88 14.00LK-HCS-0300-3-160-50* 3.00 mm 3 mm 16.0 mm 50 mm 18.00 17.10 16.20 15.30 14.40LK-HCS-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20LK-HCS-0300-6-160-50* 3.00 mm 6 mm 16.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00LK-HCS-0400-4-060-40* 4.00 mm 4 mm 6.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40LK-HCS-0400-4-100-40* 4.00 mm 4 mm 10.0 mm 40 mm 19.00 18.05 17.10 16.15 15.20LK-HCS-0400-4-140-50* 4.00 mm 4 mm 14.0 mm 50 mm 20.00 19.00 18.00 17.00 16.00LK-HCS-0400-4-180-50* 4.00 mm 4 mm 18.0 mm 50 mm 21.00 19.95 18.90 17.85 16.80LK-HCS-0400-4-220-60* 4.00 mm 4 mm 22.0 mm 60 mm 22.00 20.90 19.80 18.70 17.60LK-HCS-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 24.00 22.80 21.60 20.40 19.20LK-HCS-0400-6-160-50* 4.00 mm 6 mm 16.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00LK-HCS-0500-5-160-60* 5.00 mm 5 mm 16.0 mm 60 mm 25.00 23.75 22.50 21.25 20.00LK-HCS-0500-6-140-50* 5.00 mm 6 mm 14.0 mm 50 mm 25.00 23.75 22.50 21.25 20.00LK-HCS-0500-6-220-60* 5.00 mm 6 mm 22.0 mm 60 mm 27.00 25.65 24.30 22.95 21.60LK-HCS-0600-6-140-50* 6.00 mm 6 mm 14.0 mm 50 mm 29.00 27.55 26.10 24.65 23.20LK-HCS-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 31.00 29.45 27.90 26.35 24.80LK-HCS-0600-6-320-70* 6.00 mm 6 mm 32.0 mm 70 mm 33.00 31.35 29.70 28.05 26.40LK-HCS-0800-8-220-60* 8.00 mm 8 mm 22.0 mm 60 mm 40.00 38.00 36.00 34.00 32.00LK-HCS-0800-8-320-75* 8.00 mm 8 mm 32.0 mm 75 mm 42.00 39.90 37.80 35.70 33.60LK-HCS-1000-10-320-75* 10.00 mm 10 mm 32.0 mm 75 mm 52.00 49.40 46.80 44.20 41.60
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Wood
New
Carbide Tools | Diamond Tools 67
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Com
posite C
utters
L1
D2 D1
L2
WoodCompo-
sitesPCBs
Ceramics,Graphite
PCB outline cutters, diamond-toothed
Description:A diamond-toothed tool which has been especially op-timised for machining printed circuit boards. Its special kind of carbide cutting edge resembles the structure of diamonds and facilitates a very good endurance. The tool has a fishtail grinding at its tip. On request, it is also available with a 1/8 inch shank.
Coating:Some tools have the extra hard diamond coating Micro-Speed (see page 13).
Fields of application:Ideal for machining printed circuit boards, but also other GRP/CRP materials and wood.
Stop ring:Equipped with a purple stop ring, distance from tool tip to back of ring: 21 mm; on request also available without stop ring.
The diamond-toothing facilitates a long endurance.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-0080-3-050-38 0.80 mm 3 mm 5.0 mm 38 mm 9.00 8.55 8.10 7.65 7.20 LK-0100-3-050-38 1.00 mm 3 mm 5.0 mm 38 mm 9.00 8.55 8.10 7.65 7.20 LK-0160-3-085-38 1.60 mm 3 mm 8.5 mm 38 mm 9.00 8.55 8.10 7.65 7.20 LK-0200-3-090-38 2.00 mm 3 mm 9.0 mm 38 mm 9.00 8.55 8.10 7.65 7.20 LK-0300-3-105-38 3.00 mm 3 mm 10.5 mm 38 mm 9.00 8.55 8.10 7.65 7.20
With MicroSpeed coating, layer thickness 9.0 µm ± 3.0:1
LK-0100-3-050-38-DIA* 1.00 mm 3 mm 5.0 mm 38 mm 18.00 17.10 16.20 15.30 14.40 LK-0200-3-090-38-DIA* 2.00 mm 3 mm 9.0 mm 38 mm 18.00 17.10 16.20 15.30 14.40 LK-0300-3-105-38-DIA* 3.00 mm 3 mm 10.5 mm 38 mm 18.00 17.10 16.20 15.30 14.40
* new tool in this printed issue1 as the diamond layer is an electrical isolator, these tools are not suitable for a measurement with the automatic z adjustment.Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
3new
tools
When you are machining abrasive materials and they should be milled through completely, please take care that the fishtail grind-ing will fully immerse into the run-out material (vacuum fleece etc.), as it is most susceptible to wear.
Practical Tip
Carbide Tools | Diamond Tools68
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esC
ompo
site
C
utte
rs
L1
D2 D1L2
WoodCompo-
sitesPCBs
Ceramics,Graphite
PCB outline cutters, spiral-toothed
Description:A spiral-toothed tool which has been especially opti-mised for machining printed circuit boards. This grind-ing facilitates a very good chip clearance which leads to smoother surfaces. This cutter has a fishtail grinding at its tip and is also available with a 1/8 inch shank, on request.
Coating:The tools are also available with the extra hard diamond coating MicroSpeed (see page 13).
Fields of application:Ideal for machining printed circuit boards, but also other GRP/CRP materials and wood.
Stop ring:Equipped with a purple stop ring, distance from tool tip to back of ring: 21 mm; on request also available without stop ring.
The spiral-toothing facilitates a good chip clearance.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
LK-SV-0100-3-050-38 1.00 mm 3 mm 5.0 mm 38 mm 9.00 8.55 8.10 7.65 7.20LK-SV-0200-3-090-38 2.00 mm 3 mm 9.0 mm 38 mm 9.00 8.55 8.10 7.65 7.20LK-SV-0300-3-090-38 3.00 mm 3 mm 9.0 mm 38 mm 9.00 8.55 8.10 7.65 7.20
With MicroSpeed coating, layer thickness 9.0 µm ± 3.0:1
LK-SV-0100-3-050-38-DIA 1.00 mm 3 mm 5.0 mm 38 mm 18.00 17.10 16.20 15.30 14.40 LK-SV-0200-3-090-38-DIA 2.00 mm 3 mm 9.0 mm 38 mm 18.00 17.10 16.20 15.30 14.40 LK-SV-0300-3-090-38-DIA 3.00 mm 3 mm 9.0 mm 38 mm 18.00 17.10 16.20 15.30 14.40
1 as the diamond layer is an electrical isolator, these tools are not suitable for a measurement with the automatic z adjustment.Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
When you are machining abrasive materials and they should be milled through completely, please take care that the fishtail grind-ing will fully immerse into the run-out material (vacuum fleece etc.), as it is most susceptible to wear.
Practical Tip
Carbide Tools | Diamond Tools 69
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Com
posite C
utters
Carbide Tools | Diamond Tools70
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Engraving Toolsvhf offers gravers and engraver’s milling cutters with a wide range of sizes and top angles for machining materials from plastics to stainless steel. Gravers with a shank diameter from 6 mm on are balanced by default. On top of that, there is a special tool for engraving isolation channels on printed circuit boards.
Gravers
Box gravers
Engraver’s milling cutters for acrylic
Engraver’s milling cutters for stainless steel
Channel cutters
Isolation engraving tool
Semi-finished gravers
Free delivery at shop.vhf.de
L1
D2
D1
α
GraversDescription:Gravers are conic tools (halved carbide rod) with one cutting edge. The deeper the graver immerses into your workpiece, the broader becomes the engraving. The relationship between immersion depth and engrav-ing width is determined by the top angle of the tool. A smaller top angle enables a more constant engraving width, even if the surface is not absolutely plane. We rec-ommend our special 15° gravers for spindles without workpiece levelling. On request, we can also produce special designs. New: All gravers with a shank diameter of 6 mm up from 36° top angle have a balance grinding for an improved true-running accuracy.
Fields of application:Optimal for plastics, non-ferrous metals and wood.
Stop ring:3 mm gravers are equipped with a white stop ring, dis-tance from tool tip to back of ring: 21 mm; stop rings for 4 and 6 mm gravers can be found on page 120.
Top angles from 15° on for a constant engraving width.
Dimensions and prices
Article no.
αTop
angle
D1Engraving
width
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
GS-015-010-3-40 15° 0.10 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-015-020-3-40 15° 0.20 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-015-030-3-40 15° 0.30 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-015-030-6-30* 15° 0.30 mm 6 mm 30 mm 18.00 17.10 16.20 15.30 14.40GS-015-040-3-40 15° 0.40 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-015-050-3-40 15° 0.50 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-015-050-6-30* 15° 0,50 mm 6 mm 30 mm 18,00 17,10 16,20 15,30 14,40GS-015-070-3-40 15° 0.70 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-015-100-3-40 15° 1.00 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60
GS-036-010-3-40 36° 0.10 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-036-010-4-40 36° 0.10 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-036-010-6-40 36° 0.10 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-036-020-3-40 36° 0.20 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-036-020-4-40 36° 0.20 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-036-020-6-40 36° 0.20 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-036-030-3-40 36° 0.30 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-036-030-4-40 36° 0.30 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-036-030-6-40 36° 0.30 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-036-040-3-40 36° 0.40 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-036-040-4-40 36° 0.40 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-036-040-6-40 36° 0.40 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-036-050-3-40 36° 0.50 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-036-050-4-40 36° 0.50 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-036-050-6-40 36° 0.50 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-036-070-3-40 36° 0.70 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-036-070-4-40 36° 0.70 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-036-070-6-40 36° 0.70 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40
...
regrindable
2new
tools
Carbide Tools | Diamond Tools72
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esEn
grav
ing
Tool
s
L1
D2
D1
α
Non-ferr.Metals
PlasticsRigid Foam
Wood
Continuation
Article no.
αTop
angle
D1Engraving
width
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
GS-036-100-3-40 36° 1.00 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-036-100-4-40 36° 1.00 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-036-100-6-40 36° 1.00 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40
GS-060-010-3-40 60° 0.10 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-060-010-4-40 60° 0.10 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-060-010-6-40 60° 0.10 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-060-020-3-40 60° 0.20 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-060-020-4-40 60° 0.20 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-060-020-6-40 60° 0.20 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-060-030-3-40 60° 0.30 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-060-030-4-40 60° 0.30 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-060-030-6-40 60° 0.30 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-060-040-3-40 60° 0.40 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-060-040-4-40 60° 0.40 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-060-040-6-40 60° 0.40 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-060-050-3-40 60° 0.50 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-060-050-4-40 60° 0.50 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-060-050-6-40 60° 0.50 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-060-070-3-40 60° 0.70 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-060-070-4-40 60° 0.70 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-060-070-6-40 60° 0.70 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-060-100-3-40 60° 1.00 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-060-100-4-40 60° 1.00 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-060-100-6-40 60° 1.00 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40
GS-090-010-3-40 90° 0.10 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-090-010-4-40 90° 0.10 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-090-010-6-40 90° 0.10 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-090-020-3-40 90° 0.20 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-090-020-4-40 90° 0.20 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-090-020-6-40 90° 0.20 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-090-030-3-40 90° 0.30 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-090-030-4-40 90° 0.30 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-090-030-6-40 90° 0.30 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-090-040-3-40 90° 0.40 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-090-040-4-40 90° 0.40 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-090-040-6-40 90° 0.40 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-090-050-3-40 90° 0.50 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-090-050-4-40 90° 0.50 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-090-050-6-40 90° 0.50 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-090-070-3-40 90° 0.70 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-090-070-4-40 90° 0.70 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-090-070-6-40 90° 0.70 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-090-100-3-40 90° 1.00 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-090-100-4-40 90° 1.00 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-090-100-6-40 90° 1.00 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.We offer a regrinding service at a price of € 8 per tool (our usual scales of discount are effective). Please send us your tools for regrinding individually wrapped so that they can not damage each other in transport.
Carbide Tools | Diamond Tools 73
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Engraving Tools
L1
D2
D1
D3
α
Non-ferr.Metals
PlasticsRigid Foam
Wood
Box graversDescription:These special gravers with a top angle of 92° are very well suitable for bevelling. The material will be cut through nearly completely and bent up then. The over-size of 2° equals tolerances and offers space for glue. The name of the tool – box graver – results from its usage: it can be used for producing boxes, or more generally, for cabinet making. For calculating the maximum mate-rial thickness which you can process with this tool, just subtract the engraving width (tip diameter of the grav-er) from the half cutting edge diameter. All box gravers with a shank diameter of 6 mm and more have a balance grinding for an improved true-running accuracy. For bendings in aluminium composite plates you find a spe-cial tool on page 34 and page 93.
Fields of application:Universal tools for plastics, wood and aluminium.
Ideal for producing boxes and furniture.
Dimensions and prices
regrindable
Article no.
αTop
angle
D3Cutting edge
diameter
D1Engraving
width
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
GS-092-0300-010-3-40 92° 3.00 mm 0.10 mm 3 mm 40 mm 12.00 11.40 10.80 10.20 9.60GS-092-0400-020-4-40 92° 4.00 mm 0.20 mm 4 mm 40 mm 14.00 13.30 12.60 11.90 11.20GS-092-0600-020-4-40 92° 6.00 mm 0.20 mm 4 mm 40 mm 30.00 28.50 27.00 25.50 24.00GS-092-0600-020-6-40 92° 6.00 mm 0.20 mm 6 mm 40 mm 18.00 17.10 16.20 15.30 14.40GS-092-0800-030-6-50 92° 8.00 mm 0.30 mm 6 mm 50 mm 40.00 38.00 36.00 34.00 32.00GS-092-0800-030-8-50 92° 8.00 mm 0.30 mm 8 mm 50 mm 35.00 33.25 31.50 29.75 28.00GS-092-1000-040-6-50 92° 10.00 mm 0.40 mm 6 mm 50 mm 55.00 52.25 49.50 46.75 44.00GS-092-1000-040-10-50 92° 10.00 mm 0.40 mm 10 mm 50 mm 45.00 42.75 40.50 38.25 36.00GS-092-1200-050-12-50 92° 12.00 mm 0.50 mm 12 mm 50 mm 55.00 52.25 49.50 46.75 44.00GS-092-1600-050-12-60 92° 16.00 mm 0.50 mm 12 mm 60 mm 95.00 90.25 85.50 80.75 76.00
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.We offer a regrinding service at a price of € 8 for each tool with a cutting edge diameter of up to 6 mm and € 12 for each tool with a cutting edge diameter of 8 mm and more (our usual scales of discount are effective). Please send us your tools for regrinding individu-ally wrapped so that they can not damage each other in transport.
Carbide Tools | Diamond Tools74
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esEn
grav
ing
Tool
s
L4
L1
D2
D1
α
Non-ferr.Metals
PlasticsWood
Engraver’s milling cutters for acrylic
Description:Engraver’s milling cutters are – like the gravers – conic tools with one cutting edge and a top angle of 30, 60 or 90°. The additional polished spiral flute enables a very good chip clearance. Thus your engravings are per-formed burr-free and clean cut. On top of that, due to a higher feed rate, the total chip removal rate is increased, too.
The tools with 8 mm shank have a partly cylindric cut-ting edge. The maximum immersion depth of the 30° tool is 22 mm, the two other tools have a maximum im-mersion depth of 12 mm each.
Fields of application:Special cutters for engraving acrylic glass, but also for engraving other sorts of plastics and non-ferrous metals.
Polished flute for burr-free engravings in acrylic glass.
Dimensions and prices 3new
tools
Article no.
αTop
angle
D1Engraving
width
D2Shank
diameter
L4Max. immer-
sion depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
GF-030K-020-3-40 30° 0.20 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-030K-020-4-40 30° 0.20 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-030K-020-6-40 30° 0.20 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-030K-050-3-40 30° 0.50 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-030K-050-4-40 30° 0.50 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-030K-050-6-40 30° 0.50 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-030K-050-8-0220-60* 30º 0.50 mm 8 mm 22.0 mm 60 mm 38.00 36.10 34.20 32.30 30.40GF-030K-070-3-40 30° 0.70 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-030K-070-4-40 30° 0.70 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-030K-070-6-40 30° 0.70 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-060K-020-3-40 60° 0.20 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-060K-020-4-40 60° 0.20 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-060K-020-6-40 60° 0.20 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-060K-050-3-40 60° 0.50 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-060K-050-4-40 60° 0.50 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-060K-050-6-40 60° 0.50 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-060K-050-8-0120-50* 60º 0.50 mm 8 mm 12.0 mm 50 mm 38.00 36.10 34.20 32.30 30.40GF-060K-070-3-40 60° 0.70 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-060K-070-4-40 60° 0.70 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-060K-070-6-40 60° 0.70 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-090K-020-3-40 90° 0.20 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-090K-020-4-40 90° 0.20 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-090K-020-6-40 90° 0.20 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-090K-050-3-40 90° 0.50 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-090K-050-4-40 90° 0.50 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-090K-050-6-40 90° 0.50 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20GF-090K-050-8-0120-50* 90º 0.50 mm 8 mm 12.0 mm 50 mm 38.00 36.10 34.20 32.30 30.40GF-090K-070-3-40 90° 0.70 mm 3 mm 40 mm 18.00 17.10 16.20 15.30 14.40GF-090K-070-4-40 90° 0.70 mm 4 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-090K-070-6-40 90° 0.70 mm 6 mm 40 mm 24.00 22.80 21.60 20.40 19.20
* new tool in this printed issue
Rigid Foam
Carbide Tools | Diamond Tools 75
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Engraving Tools
L1
D2
D1
α
Ferrous Metals
Engraver’s milling cutters for stainless steel
Description:This engraver’s milling cutter has a very short cutting edge and a very stable geometry (three-quarter car-bide rod with a flute), it has a top angle of 35° or 60°.
Coating:By default, this tool is coated with a TINALOX® SN² thin layer coating (see page 12) with a thickness of 1.5 µm ± 0.5 for machining stainless steel. This makes it ideal for engraving very hard metal types.
Fields of application:Special tool for engraving steel, stainless steel and very hard non-ferrous metals.
Please use only an appropriate lubricant for cooling, e. g. AquaTec®, WST 20 or the cutting oil spray Alpha 93 (see page 121).
Considerable advantages in stainless steel.
Dimensions and prices
Article no.
αTop
angle
D1Engraving
width
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
GF-035V-020-3-40 35° 0.20 mm 3 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-035V-020-4-40* 35° 0.20 mm 4 mm 40 mm 22.00 20.90 19.80 18.70 17.60GF-035V-020-6-40 35° 0.20 mm 6 mm 40 mm 26.00 24.70 23.40 22.10 20.80GF-035V-040-3-40 35° 0.40 mm 3 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-035V-040-4-40* 35° 0.40 mm 4 mm 40 mm 22.00 20.90 19.80 18.70 17.60GF-035V-040-6-40 35° 0.40 mm 6 mm 40 mm 26.00 24.70 23.40 22.10 20.80
GF-060V-020-3-40 60° 0.20 mm 3 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-060V-020-4-40* 60° 0.20 mm 4 mm 40 mm 22.00 20.90 19.80 18.70 17.60GF-060V-020-6-40 60° 0.20 mm 6 mm 40 mm 26.00 24.70 23.40 22.10 20.80GF-060V-040-3-40 60° 0.40 mm 3 mm 40 mm 20.00 19.00 18.00 17.00 16.00GF-060V-040-4-40* 60° 0.40 mm 4 mm 40 mm 22.00 20.90 19.80 18.70 17.60GF-060V-040-6-40 60° 0.40 mm 6 mm 40 mm 26.00 24.70 23.40 22.10 20.80
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
4new
tools
Non-ferr.Metals
Carbide Tools | Diamond Tools76
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esEn
grav
ing
Tool
s
L1
D1
αD2L2
L3
Compo-sites
Channel cuttersDescription:This graver has a parallel tip with a top angle of 180°. The cutting edges are regrindable.
Fields of application:Used for milling die channels in pressed paper sheets (e. g. Pertinax®) or high pressure laminates (HPL) e. g. when counter dies have to be applied for corrugated board.
Graver with 180° top angle for milling die channels.
Dimensions and prices
regr
inda
ble
New
Article no.
αTop
angle
D1Engraving
width
D2Shank
diameter
L2Cut. edge
length
L3bisecting
depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
GS-180-080-3-40* 180º 0.80 mm 3 mm 3.0 mm 4.5 mm 40 mm 11.00 10.45 9.90 9.35 8.80GS-180-100-3-40* 180º 1.00 mm 3 mm 3.0 mm 4.5 mm 40 mm 11.00 10.45 9.90 9.35 8.80GS-180-120-3-40* 180º 1.20 mm 3 mm 3.0 mm 4.5 mm 40 mm 11.00 10.45 9.90 9.35 8.80GS-180-130-3-40* 180º 1.30 mm 3 mm 3.0 mm 4.5 mm 40 mm 11.00 10.45 9.90 9.35 8.80GS-180-140-3-40* 180º 1.40 mm 3 mm 3.0 mm 4.5 mm 40 mm 11.00 10.45 9.90 9.35 8.80GS-180-200-3-40* 180º 2.00 mm 3 mm 3.0 mm 4.5 mm 40 mm 11.00 10.45 9.90 9.35 8.80
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.We offer a regrinding service at a price of € 6 per tool (our usual scales of discount are effective). Please send us your tools for regrinding individually wrapped so that they can not damage each other in transport.
Carbide Tools | Diamond Tools 77
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Engraving Tools
L1
D2
D1
α
Non-ferr.Metals
PlasticsCompo-
sitesPCBs
Isolation engraving toolDescription:The tip of this conic special tool is tapered from 0.05 to 1.0 mm with a top angle of 90°. This results in extremely burr-free and finely cleared out isolation channels. This is for instance decisive for your success when you produce prototypes of printed circuit boards.
Fields of application:Printed circuit board prototyping by engraving isolation channels.
Special features:Its high endurance and stability even at high rates of feed make this tool an ideal fine engraving tool for nearly all kinds of materials.
Stop ring:All cutters are equipped with a red stop ring, distance from tool tip to back of ring for L1 = 30 mm: 15 mm, for L1 = 40 mm: 21 mm; on request also available without stop ring.
PCB prototyping tool with long endurance.
Dimensions and prices
Article no.
αtop
angle
D1Cutting edge
diameter
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
RS-ISO-090-3-30 90° 1.00 mm 3 mm 30 mm 10.00 9.50 9.00 8.50 8.00RS-ISO-090-3-40* 90° 1.00 mm 3 mm 40 mm 10.00 9.50 9.00 8.50 8.00
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
1new
tool
Carbide Tools | Diamond Tools78
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esEn
grav
ing
Tool
s
L1
D2L3
½ D2 + 0,02 mm
Semi-finished graversDescription:You can get our gravers also semi-finished with pre-ground profile which you can finish according to your demands. These products are carbide rods which are halved at one end with different depths. The halving is 0.02 mm over the centre.
Please note:These semi-finished products are not directly usable tools. They cannot be used without grinding them ap-propriately before.
Semi-finished gravers for grinding them by yourself.
Dimensions and prices
Article no.
D2Shank
diameter
L3Halving
depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
GS-HZ-3-10-40* 3 mm 10 mm 40 mm 6.00 5.70 5.40 5.10 4.80GS-HZ-4-10-40* 4 mm 10 mm 40 mm 7.50 7.13 6.75 6.38 6.00GS-HZ-4-15-50* 4 mm 15 mm 50 mm 9.50 9.03 8.55 8.08 7.60GS-HZ-6-10-40* 6 mm 10 mm 40 mm 9.00 8.55 8.10 7.65 7.20GS-HZ-6-15-50* 6 mm 15 mm 50 mm 11.00 10.45 9.90 9.35 8.80GS-HZ-6-20-50* 6 mm 20 mm 50 mm 12.00 11.40 10.80 10.20 9.60
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
New
Carbide Tools | Diamond Tools 79
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Engraving Tools
Carbide Tools | Diamond Tools80
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Deburring ToolsThese tools can be used for deburring, coun-tersinking, chamfering and edge-working of non-ferrous metals and plastics. They are avail-able with top angles of 60°, 90° and 120° and a quadrant grinding.
Deburring tools
Deburring tools, quadrant
Free delivery at shop.vhf.de
L1
D2 D1
L2
α
Non-ferr.Metals
PlasticsRigid Foam
Ferrous Metals
Deburring toolsDescription:Tools with a cutting edge diameter of up to 8 mm have 4 cutting edges, tools with a diameter of 10 mm or more have 5 cutting edges. These tools have a top angle of 60°, 90° or 120°. In contrast to conventional deburr-ing tools, this type can also be used at high rotational speeds for deburring or chamfering all kinds of con-tours quickly. It is recommended to use this type espe-cially with larger tool diameters in a high frequency spin-dle due to its very little unbalance. The life of the spindle will be prolonged and your results will be improved.
Coating:All tools are TINALOX® SN² coated (see page 12) with a thickness of 3.0 µm ± 1.0.
Fields of application:This tool is optimally suited for deburring and chamfer-ing plastics, non-ferrous metals and steel.
If you machine steel and other ferrous metals with these tools, please use only an appropriate lubricant for cool-ing, e. g. AquaTec®, WST 20 or the cutting oil spray Al-pha 93 (see page 121).
No chance for burrs with this special tool.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
α = 60° top angle:EG-060-0400-6-034-40 4.00 mm 6 mm 3.4 mm 40 mm 22.00 20.90 19.80 18.70 17.60EG-060-0600-6-052-40 6.00 mm 6 mm 5.2 mm 40 mm 22.00 20.90 19.80 18.70 17.60EG-060-0800-8-069-50 8.00 mm 8 mm 6.9 mm 50 mm 32.00 30.40 28.80 27.20 25.60EG-060-1000-6-086-50* 10.00 mm 6 mm 8.6 mm 50 mm 48.00 45.60 43.20 40.80 38.40EG-060-1000-10-086-50* 10.00 mm 10 mm 8.6 mm 50 mm 38.00 36.10 34.20 32.30 30.40
α = 90° top angle:EG-090-0300-6-015-40 3.00 mm 6 mm 1.5 mm 40 mm 22.00 20.90 19.80 18.70 17.60EG-090-0400-4-020-40* 4.00 mm 4 mm 2.0 mm 40 mm 18.00 17.10 16.20 15.30 14.40EG-090-0400-6-020-40 4.00 mm 6 mm 2.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60EG-090-0600-6-030-40 6.00 mm 6 mm 3.0 mm 40 mm 22.00 20.90 19.80 18.70 17.60EG-090-0800-8-040-50 8.00 mm 8 mm 4.0 mm 50 mm 32.00 30.40 28.80 27.20 25.60EG-090-1000-6-050-50* 10.00 mm 6 mm 5.0 mm 50 mm 48.00 45.60 43.20 40.80 38.40EG-090-1000-10-050-50 10.00 mm 10 mm 5.0 mm 50 mm 38.00 36.10 34.20 32.30 30.40EG-090-1200-12-060-50 12.00 mm 12 mm 6.0 mm 50 mm 48.00 45.60 43.20 40.80 38.40
α = 120° top angle:EG-120-0600-6-017-40* 6.00 mm 6 mm 1.7 mm 40 mm 22.00 20.90 19.80 18.70 17.60EG-120-0800-8-023-50* 8.00 mm 8 mm 2.3 mm 50 mm 32.00 30.40 28.80 27.20 25.60EG-120-1000-6-028-50* 10.00 mm 6 mm 2.8 mm 50 mm 48.00 45.60 43.20 40.80 38.40EG-120-1000-10-028-50* 10.00 mm 10 mm 2.8 mm 50 mm 38.00 36.10 34.20 32.30 30.40
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
8new
tools
Carbide Tools | Diamond Tools82
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
ebur
ring
To
ols
L1
D2 D1
L2
Non-ferr.Metals
PlasticsRigid Foam
Deburring tools, quadrantDescription:The quadrant grinding of this tool with four teeth cre-ates smooth round chamferings.
Coating:On request, the deburring tools are also available with a TINALOX® SN² coating or with the super-hard diamond coating SHC® for machining steel or composites (see page 12).
Fields of application:This tool is suitable for chamfering plastics and non-ferrous metals.
Rounded chamferings due to quadrant grinding.
Dimensions and prices
Article no.
L2
Radius
D1Head
diameter
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
EG-R05-0500-6-50 0.5 mm 5.00 mm 6 mm 50 mm 22.00 20.90 19.80 18.70 17.60EG-R10-0400-6-50 1.0 mm 4.00 mm 6 mm 50 mm 22.00 20.90 19.80 18.70 17.60EG-R15-0300-6-50 1.5 mm 3.00 mm 6 mm 50 mm 22.00 20.90 19.80 18.70 17.60EG-R20-0200-6-50 2.0 mm 2.00 mm 6 mm 50 mm 22.00 20.90 19.80 18.70 17.60EG-R25-0300-8-50 2.5 mm 3.00 mm 8 mm 50 mm 32.00 30.40 28.80 27.20 25.60EG-R30-0200-8-50 3.0 mm 2.00 mm 8 mm 50 mm 32.00 30.40 28.80 27.20 25.60EG-R35-0300-10-50* 3.5 mm 3.00 mm 10 mm 50 mm 42.00 39.90 37.80 35.70 33.60EG-R40-0200-10-50* 4.0 mm 2.00 mm 10 mm 50 mm 42.00 39.90 37.80 35.70 33.60
* new tool in this PDF updateAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
2new
tools
Carbide Tools | Diamond Tools 83
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Deburring Tools
Carbide Tools | Diamond Tools84
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Router BitsRouter bits are mostly used for machining wood. However, due to their carbide cutting edges they are also very well suitable for work-ing on other kinds of materials like plastics.
The router bits are available as different types for chamfering or bevelling, for milling slots, characters and concave or convex radii, and for surface milling. The Orange ToolsTM are manu-factured by CMT, an experienced specialist for woodworking tools. The paint serves also as non-stick coating to prevent that resins and impurities may accumulate at the cutting edge.
V slot cutters
Long hole slot cutters
Slot cutters
Character cutter
Radius cutters
Chamfering cutters
Cutters with quadrant
V slot cutters for aluminium composites
Triple tooth surface milling cutters
Free delivery at shop.vhf.de
L1
D2 D1
L2
α
PlasticsRigid Foam
Wood
V-slot cuttersDescription:The tool is made of a massive steel body with two inte-grated carbide cutting edges and 90° top angle respec-tively three cutting edges and 60° top angle. The 90° tools also have a cylindric part of the cutting edge.
Fields of application:This tool can be used in various ways: for milling (deco-ration) slots, chamfering and engraving. Especially the tool with 60° top angle is suitable for engraving. With small immersion depths you engrave fine lines, if you use the full cutting edge length you will get quite prominent letterings.
Two top angles for different V slots.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Max. immersion
depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
α = 60° top angle, triple tooth cutters:RB-VN-060-1270-6-110-57 12.70 mm 6 mm 11.0 mm 57 mm 37,00 35,15 33,30 31,45RB-VN-060-1270-8-110-57 12.70 mm 8 mm 11.0 mm 57 mm 37,00 35,15 33,30 31,45
α = 90° top angle. double tooth cutters:RB-VN-090-0950-6-127-45 9.50 mm 6 mm 12.7 mm 45 mm 31,00 29,45 27,90 26,35RB-VN-090-0950-8-127-45 9.50 mm 8 mm 12.7 mm 45 mm 31,00 29,45 27,90 26,35RB-VN-090-1270-6-127-45 12.70 mm 6 mm 12.7 mm 45 mm 29,00 27,55 26,10 24,65RB-VN-090-1270-8-127-45 12.70 mm 8 mm 12.7 mm 45 mm 29,00 27,55 26,10 24,65RB-VN-090-1600-8-127-53 16.00 mm 8 mm 12.7 mm 53 mm 35,00 33,25 31,50 29,75RB-VN-090-1900-6-160-56 19.00 mm 6 mm 16.0 mm 56 mm 35,00 33,25 31,50 29,75RB-VN-090-3170-8-160-64 31.70 mm 8 mm 16.0 mm 64 mm 57,00 54,15 51,30 48,45RB-VN-090-3800-8-190-64* 38.00 mm 8 mm 19.0 mm 64 mm 62,00 58,90 55,80 52,70
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
1new
tool
Carbide Tools | Diamond Tools86
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esRo
uter
Bits
L1
D2 D1
L2
PlasticsRigid Foam
Wood
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-LN-1600-6-190-54 16.00 mm 6 mm 19.0 mm 54 mm 24.00 22.80 21.60 20.40RB-LN-1600-8-190-54 16.00 mm 8 mm 19.0 mm 54 mm 24.00 22.80 21.60 20.40RB-LN-1800-6-160-48 18.00 mm 6 mm 16.0 mm 48 mm 26.00 24.70 23.40 22.10RB-LN-1800-8-160-48 18.00 mm 8 mm 16.0 mm 48 mm 26.00 24.70 23.40 22.10RB-LN-2000-6-160-48 20.00 mm 6 mm 16.0 mm 48 mm 28.00 26.60 25.20 23.80RB-LN-2000-8-160-48 20.00 mm 8 mm 16.0 mm 48 mm 28.00 26.60 25.20 23.80
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
Long hole slot cuttersDescription:The tool is made of a massive steel body with two in-tegrated carbide cutting edges. It is slotted straightly and has a negative cutting angle for perfectly even sur-faces. This prevents also fraying out of the material.
Fields of application:For producing tongue and groove or mortice and tenon joints, for milling space for hinges etc.
Milling slots with perfectly even surfaces.
Carbide Tools | Diamond Tools 87
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Router Bits
L1
D2 D1
L2
PlasticsRigid Foam
Wood
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-NF-1000-6-317-60 10.00 mm 6 mm 31.7 mm 60 mm 30.00 28.50 27.00 25.50RB-NF-1000-8-317-60 10.00 mm 8 mm 31.7 mm 60 mm 30.00 28.50 27.00 25.50RB-NF-1200-6-317-60 12.00 mm 6 mm 31.7 mm 60 mm 30.00 28.50 27.00 25.50RB-NF-1200-8-317-60 12.00 mm 8 mm 31.7 mm 60 mm 30.00 28.50 27.00 25.50RB-NF-1500-6-317-66 15.00 mm 6 mm 31.7 mm 66 mm 34.00 32.30 30.60 28.90RB-NF-1500-8-317-66 15.00 mm 8 mm 31.7 mm 66 mm 34.00 32.30 30.60 28.90RB-NF-1600-6-317-66 16.00 mm 6 mm 31.7 mm 66 mm 34.00 32.30 30.60 28.90RB-NF-1600-8-317-66 16.00 mm 8 mm 31.7 mm 66 mm 34.00 32.30 30.60 28.90
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
Slot cuttersDescription:The tool is made of a massive steel body with two in-tegrated carbide cutting edges. It is slotted straightly, sharp like a razor blade and radially ground for perfect surfaces.
Fields of application:Suitable for milling plane surfaces, slots for letters or blunt connections, notches, tongue and groove joints etc.
Practical tip:We recommend the milling cutter with article number RB-NF-1600-8-317-66 for the usage in all rotary current spindles for plane-milling the surface of vhf special vac-uum tables.
Thanks to its long cutting edge suitable for deep slots.
Carbide Tools | Diamond Tools88
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esRo
uter
Bits
L1
D2 D1
L2
α
PlasticsRigid Foam
Wood
Dimensions and prices
Character cutterDescription:The tool is made of a massive steel body with two in-tegrated carbide cutting edges. It is slotted straightly with a top angle of 60°. The radius at the tip of the tool is 3.2 mm. The tool also has a cylindric part of the cutting edge.
Fields of application:Effective removal of the material around the free stand-ing letters.
You can achieve striking effects with free standing letters.
Article no.
αtop
anglel
D1Cutting edge
diameter
D2Shank
diameter
L2Max. immersion
depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-SF-2540-6-190-51 60° 25.40 mm 6 mm 19.0 mm 51 mm 44.00 41.80 39.60 37.40
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
Carbide Tools | Diamond Tools 89
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Router Bits
L1
D2 D1
L2
PlasticsRigid Foam
Wood
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Max. immersion
depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-RF-0320-6-095-511 3.20 mm 6 mm 9.5 mm 51 mm 30.00 28.50 27.00 25.50RB-RF-0600-6-127-511 6.00 mm 6 mm 12.7 mm 51 mm 30.00 28.50 27.00 25.50RB-RF-0950-6-064-51 9.50 mm 6 mm 6.4 mm 51 mm 30.00 28.50 27.00 25.50RB-RF-1270-6-095-51 12.70 mm 6 mm 9.5 mm 51 mm 30.00 28.50 27.00 25.50RB-RF-1270-8-095-51 12.70 mm 8 mm 9.5 mm 51 mm 30.00 28.50 27.00 25.50RB-RF-1580-6-095-51 15.80 mm 6 mm 9.5 mm 51 mm 32.00 30.40 28.80 27.20RB-RF-1580-8-095-51 15.80 mm 8 mm 9.5 mm 51 mm 32.00 30.40 28.80 27.20RB-RF-1900-6-115-51 19.00 mm 6 mm 11.5 mm 51 mm 34.00 32.30 30.60 28.90RB-RF-1900-8-115-51 19.00 mm 8 mm 11.5 mm 51 mm 34.00 32.30 30.60 28.90
1 Radius cutters with a cutting edge diameter of up to 6 mm are made of solid carbide.Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
Radius cuttersDescription:The tool is made of a massive steel body with two inte-grated carbide cutting edges which form a semi-circu-lar tool tip. The tools also have a cylindric part of the cutting edge. You will find quarter rod milling cutters with concave radius on page 92.
Fields of application:For milling rounded concave slots and for mould mak-ing.
For rounded slots and mould making.
Carbide Tools | Diamond Tools90
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esRo
uter
Bits
β
L1
D2 D1L2
PlasticsRigid Foam
Wood
Dimensions and prices
Article no.
βChamfering
angle
D1Cutting edge
diameter
D2Shank
diameter
L2Max. immersion
depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-AF-015-2400-6-140-46 15° 24.00 mm 6 mm 14.0 mm 46 mm 26.00 24.70 23.40 22.10RB-AF-015-2400-8-140-46 15° 24.00 mm 8 mm 14.0 mm 46 mm 26.00 24.70 23.40 22.10RB-AF-030-2600-6-127-45 30° 26.00 mm 6 mm 12.7 mm 45 mm 26.00 24.70 23.40 22.10RB-AF-030-2600-8-127-45 30° 26.00 mm 8 mm 12.7 mm 45 mm 26.00 24.70 23.40 22.10RB-AF-045-2500-6-080-41 45° 25.00 mm 6 mm 8.0 mm 41 mm 26.00 24.70 23.40 22.10RB-AF-045-2500-8-080-41 45° 25.00 mm 8 mm 8.0 mm 41 mm 26.00 24.70 23.40 22.10
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
Chamfering cuttersDescription:The tool is made of a massive steel body with two inte-grated carbide cutting edges. It is slotted straightly for chamfering edges accurately (may also be used for pro-ducing polygons). The tool is available with three differ-ent chamfering angles.
Fields of application:Suitable for chamfering edges and to justify coatings.
For chamfering edges with three different angles.
Carbide Tools | Diamond Tools 91
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Router Bits
L1
D2 D1
L2L3
PlasticsRigid Foam
Wood
Dimensions and prices
Cutters with quadrantDescription:The tool is made of a massive steel body with two in-tegrated carbide cutting edges which form a concave quadrant grinding. Furthermore, the tools have a front and a cylindric part of the cutting edge. You will find radius cutters with a convex radius on page 90. For milling smaller radii, we recommend the deburring tools with quadrant which are described on page 83.
Fields of application:For milling accurately rounded convex edges or ap-propriate internal profiles. By varying the depth of im-mersion, you can create many interesting effects.
The quadrant grinding is used for rounding edges.
New
Article no.
L2Radius
D1Cutting edge
diameter
D2Shank
diameter
L3Max. immersion
depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-VK-R40-1900-8-44* 4.0 mm 19.00 mm 8 mm 12.0 mm 44 mm 33.00 31.35 29.70 28.05RB-VK-R50-2100-8-44* 5.0 mm 21.00 mm 8 mm 12.0 mm 44 mm 33.00 31.35 29.70 28.05RB-VK-R60-2300-8-44* 6.0 mm 23.00 mm 8 mm 12.0 mm 44 mm 36.00 34.20 32.40 30.60RB-VK-R80-2860-8-45* 8.0 mm 28.60 mm 8 mm 12.7 mm 45 mm 39.00 37.05 35.10 33.15RB-VK-R95-3170-8-46* 9.5 mm 31.70 mm 8 mm 14.0 mm 46 mm 39.00 37.05 35.10 33.15
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
Carbide Tools | Diamond Tools92
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esRo
uter
Bits
L1
D2 D3 αD1
V-slot cutters for aluminium composites
Description:This tool consists of a massive steel body with an inserted double-toothed carbide plate. The top angle is 90° or 135°.
Fields of application:Using the router bits, you can bend aluminium com-posites with a thickness of 3 to 6 mm. The tool with 90° produces rectangular bendings with a bottom width of 3 mm. The tool with 135° produces acute-angled bendings of 45° with a bottom width of 2 mm.
For rectangular and acute-angled bendings.
Dimensions and prices
Article no.
αTop
angle
D3Cutting edge
diameter
D1Bottom
width
D2Shank
diameter
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-AV-090-1800-6-59 90° 18.00 mm 3.0 mm 6 mm 59.0 mm 49.00 46.55 44.10 41.65RB-AV-090-1800-8-59 90° 18.00 mm 3.0 mm 8 mm 59.0 mm 49.00 46.55 44.10 41.65RB-AV-135-1800-6-59 135° 18.00 mm 2.0 mm 6 mm 59.0 mm 49.00 46.55 44.10 41.65RB-AV-135-1800-8-59 135° 18.00 mm 2.0 mm 8 mm 59.0 mm 49.00 46.55 44.10 41.65
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
The bottom width (D1) of the mill-ing cutter determines the later bending radius (r). For α = 90° it is 3 mm and for α = 135° it is 2 mm. Please note that there has to remain a rest of 0.6 to 0.8 mm of the plate which must not be milled. The maxi
mum thickness of the plate should not exceed 4 mm when you work with the 135° tool.
Practical Tip
rr = 2 – 3 mm
0,6
– 0
,8 m
m
D3∢α
D1
Alu Compo-
sites
Carbide Tools | Diamond Tools 93
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Router Bits
L1
D2 D1
L2
Triple tooth surface milling cutters
Description:This tool is made of a massive steel shank with a carbide head soldered on it. It has three cutting edges with a lead angle of 30° and an edge radius of 0.5 mm. The carbide cutting edges are regrindable for several times.
Fields of application:You can use this tool for an efficient and top quality sur-face milling of larger areas of wood-based materials and aluminium. Also suitable for plastics and rigid foams.
Triple tooth carbide head for perfect surfaces.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
RB-DS-1000-6-080-50* 10.00 mm 6 mm 8.0 mm 50 mm 29.00 27.55 26.10 24.65RB-DS-1200-6-080-50* 12.00 mm 6 mm 8.0 mm 50 mm 39.00 37.05 35.10 33.15RB-DS-1400-10-080-50* 14.00 mm 10 mm 8.0 mm 50 mm 49.00 46.55 44.10 41.65RB-DS-1600-10-080-50* 16.00 mm 10 mm 8.0 mm 50 mm 59.00 56.05 53.10 50.15RB-DS-1800-10-080-50* 18.00 mm 10 mm 8.0 mm 50 mm 69.00 65.55 62.10 58.65RB-DS-2000-10-080-50* 20.00 mm 10 mm 8.0 mm 50 mm 79.00 75.05 71.10 67.15RB-DS-3000-12-080-50* 30.00 mm 12 mm 8.0 mm 50 mm 89.00 84.55 80.10 75.65
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.Regrinding service for two or more identical tools: D1: 10 – 14 mm for € 19.–; D1: 16 – 20 mm for € 24.–; D1: 30 mm for € 29.–. From five pieces on our usual scales of discount are effective. Please send us your tools for regrinding individually wrapped so that they can not damage each other in transport.
New
Non-ferr.Metals
PlasticsRigid Foam
Wood
regrindable
Carbide Tools | Diamond Tools94
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esRo
uter
Bits
Thread CuttersYou can choose between thread whirling cut-ters and circular thread cutters. For the thread whirling cutters you will need a pre-drilled hole. The circular thread cutters drill the hole and cut the thread in the same working cycle.
Thread whirling cutters
Circular thread cutters
Free delivery at shop.vhf.de
L1
D2 D1
L2
Non-ferr.Metals
PlasticsCompo-
sitesFerrous Metals
Thread whirling cuttersDescription:This tool has two rows of teeth and is suitable for espe-cially tiny threads from M 1 on. The threads will be machined down to the bottom of the pre-drilled (tapped blind) hole. The threads can be very deep thanks to the long undercut. The number of teeth depends on the thread size: three teeth for M 1 to M 4, four teeth for M 5 to M 6 and six teeth for M 8 to M 10. The tools are de-signed for cutting metric threads and standard threads.
Coating:The tools are also available with TINALOX® SN2 coating (see page 12) which is especially recommended for machining steel.
Fields of application:The thread whirling cutter can be universally used for plastics, non-ferrous metals, composites and steel.
If you machine steel and other ferrous metals with these tools, please use only an appropriate lubricant for cool-ing, e. g. AquaTec®, WST 20 or the cutting oil spray Al-pha 93 (see page 121).Thread whirling cutters with two rows of teeth.
Dimensions and prices
Article no. Thread
D1Cutting edge
diameter
D2Shank
diameter
L2Maximum
thread depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
GW-M01-0073-3-032-40 M 1 0.73 mm 3 mm 3.2 mm 40 mm 53.00 50.35 47.70 45.05GW-M02-0155-3-064-40 M 2 1.55 mm 3 mm 6.4 mm 40 mm 53.00 50.35 47.70 45.05GW-M02.5-0200-3-080-40 M2.5 2.00 mm 3 mm 8.0 mm 40 mm 53.00 50.35 47.70 45.05GW-M03-0244-4-096-40 M 3 2.44 mm 4 mm 9.6 mm 40 mm 58.00 55.10 52.20 49.30GW-M04-0320-4-128-40 M 4 3.20 mm 4 mm 12.8 mm 40 mm 58.00 55.10 52.20 49.30GW-M05-0400-6-160-60 M 5 4.00 mm 6 mm 16.0 mm 60 mm 68.00 64.60 61.20 57.80GW-M06-0485-6-192-60 M 6 4.85 mm 6 mm 19.2 mm 60 mm 68.00 64.60 61.20 57.80GW-M08-0650-8-256-75 M 8 6.50 mm 8 mm 25.6 mm 75 mm 78.00 74.10 70.20 66.30GW-M10-0790-8-320-75 M 10 7.90 mm 8 mm 32.0 mm 75 mm 78.00 74.10 70.20 66.30
With TINALOX® SN2 coating, layer thickness 3.0 µm ± 1.0:GW-M01-0073-3-032-40-TAN M 1 0.73 mm 3 mm 3.2 mm 40 mm 57.00 54.15 51.30 48.45GW-M02-0155-3-064-40-TAN M 2 1.55 mm 3 mm 6.4 mm 40 mm 57.00 54.15 51.30 48.45GW-M02.5-0200-3-080-40-TAN M2.5 2.00 mm 3 mm 8.0 mm 40 mm 57.00 54.15 51.30 48.45GW-M03-0244-4-096-40-TAN M 3 2.44 mm 4 mm 9.6 mm 40 mm 62.00 58.90 55.80 52.70GW-M04-0320-4-128-40-TAN M 4 3.20 mm 4 mm 12.8 mm 40 mm 62.00 58.90 55.80 52.70GW-M05-0400-6-160-60-TAN M 5 4.00 mm 6 mm 16.0 mm 60 mm 72.00 68.40 64.80 61.20GW-M06-0485-6-192-60-TAN M 6 4.85 mm 6 mm 19.2 mm 60 mm 72.00 68.40 64.80 61.20GW-M08-0650-8-256-75-TAN M 8 6.50 mm 8 mm 25.6 mm 75 mm 82.00 77.90 73.80 69.70GW-M10-0790-8-320-75-TAN M 10 7.90 mm 8 mm 32.0 mm 75 mm 82.00 77.90 73.80 69.70
Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.Please note that both, controller and production software, must be able to perform a helix movement to produce a thread with this tool. This is the case for all vhf controllers starting with CNC 550 and the manufacturing software Cenon.
Carbide Tools | Diamond Tools96
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esTh
read
C
utte
rs
L1
D2L2
D1
L3
Non-ferr.Metals
Plastics
Circular thread cuttersDescription:This tool with its special tip grinding is a multifunction-al thread cutter and a tapping drill at the same time. It cuts the thread in the same working cycle in which also the tap hole is being milled. These “two tools in one” save not only an extra tool, but also a lot of time because the tool change becomes obsolete after the hole has been milled.
Fields of application:The circular thread cutter with its patented technology is suitable for plastics and non-ferrous metals. It can be used for producing metric internal threads. Each thread cutter (except M 2 and M 6) can be used for producing several thread sizes, so this saves time due to the obso-lete tool changes, too.
Thread cutter and tapping drill at the same time.
Dimensions and prices
Article no. Thread
D1Cutting edge
diameter
D2Shank
diameter
L3Additional
depth
L2Maximum
thread depth
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
BGF-M02* M 2 1.55 mm 6 mm 1.3 mm 5.5 mm 50 mm 62.00 58.90 55.80 52.70BGF-M02.5-M03 M 2.5 – M 3 2.00 mm 6 mm 1.3 mm 8.5 mm 50 mm 62.00 58.90 55.80 52.70BGF-M04-M05 M 4 – M 5 3.15 mm 6 mm 1.3 mm 10.5 mm 50 mm 62.00 58.90 55.80 52.70BGF-M06 M 6 4.80 mm 6 mm 1.3 mm 10.5 mm 50 mm 62.00 58.90 55.80 52.70BGF-M08-M10 M 8 – M 10 5.90 mm 6 mm 2.3 mm 10.5 mm 50 mm 62.00 58.90 55.80 52.70BGF-M12-M16 M 12 – M 16 5.90 mm 6 mm 2.3 mm 10.5 mm 50 mm 62.00 58.90 55.80 52.70BGF-MKV MCD1 5.90 mm 6 mm 2.3 mm 10.5 mm 50 mm 62.00 58.90 55.80 52.70BGF-PG07-PG48 PG 7 – PG 48 5.90 mm 6 mm 5.6 mm 8.5 mm 50 mm 62.00 58.90 55.80 52.70
* new tool in this printed issue1 MCG = metric cable glandAsk for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.Please note that both, controller and production software, must be able to perform a helix movement to produce a thread with this tool. This is the case for all vhf controllers starting with CNC 550 and the manufacturing software Cenon.You will find a data sheet for setting the operational parameters in the download section of our web site (download.vhf.de).
1new
tool
Carbide Tools | Diamond Tools 97
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Thread C
utters
Carbide Tools | Diamond Tools98
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
DrillsThese drills are suitable for materials like plas-tics, non-ferrous metals, printed circuit boards or thermosetting plastics and thermoplastics. With an appropriate cooling you can use them also for steel and ferrous metals. Optionally they are also available with hard coating.
Drills with 3 mm shank
Drills with 6 mm shank
Free delivery at shop.vhf.de
L1
D2 D1L2
Drills with 3 mm shankFields of application:These drills are optimal for plastics and printed circuit boards, but also well suitable for non-ferrous metals. If you would like to drill titanium, steel or stainless steel, please ask us. Drills with cutting edge diameters of up to 3 mm have a top angle of 130°, from 3.1 mm on they have a top angle of 165°. On request, these tools are also available with a 1/8 inch shank. If you want to use these drills for pre-drilling threads, please note the suitable thread sizes in the table.
Stop ring:Tools with 3 mm cutting edge diameter are equipped with a yellow stop ring, distance from tool tip to back of ring: 21 mm; on request also available without stop ring.
Drills for PCBs and other sorts of hard materials.
Dimensions and prices
Article no.for
thread
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
130° top angle:LB-0020-3-035-38 0.20 mm 3 mm 3.5 mm 38 mm 5.00 4.75 4.50 4.25 4.00LB-0030-3-035-38 0.30 mm 3 mm 3.5 mm 38 mm 5.00 4.75 4.50 4.25 4.00LB-0040-3-055-38 0.40 mm 3 mm 5.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0050-3-070-38 0.50 mm 3 mm 7.0 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0060-3-070-38 0.60 mm 3 mm 7.0 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0070-3-105-38 0.70 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0080-3-105-38 0.80 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0090-3-105-38 0.90 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0100-3-105-38 1.00 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0110-3-105-38 1.10 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0120-3-105-38 1.20 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0130-3-105-38 1.30 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0140-3-105-38 1.40 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0150-3-105-38 1.50 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0160-3-105-38 M 2 1.60 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0170-3-105-38 1.70 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0180-3-105-38 1.80 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0190-3-105-38 1.90 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0200-3-105-38 2.00 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0210-3-105-38 M 2.5 2.10 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0220-3-105-38 2.20 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0230-3-105-38 2.30 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0240-3-105-38 2.40 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0250-3-105-38 M 3 2.50 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0260-3-105-38 2.60 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0270-3-105-38 2.70 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0280-3-105-38 2.80 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0290-3-105-38 M 3.5 2.90 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60LB-0300-3-105-38 3.00 mm 3 mm 10.5 mm 38 mm 4.50 4.28 4.05 3.83 3.60
...
32new
tools
Carbide Tools | Diamond Tools100
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
rills
L1
D2 D1L2
Non-ferr.Metals
PlasticsWoodCompo-
sitesPCBs
Continuation
Article no.for
thread
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
165° top angle:LB-0310-3-120-38* 3.10 mm 3 mm 12.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60LB-0320-3-120-38* 3.20 mm 3 mm 12.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60LB-0330-3-120-38* M 4 3.30 mm 3 mm 12.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60LB-0340-3-120-38* 3.40 mm 3 mm 12.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60LB-0350-3-120-38* 3.50 mm 3 mm 12.0 mm 38 mm 9.50 9.03 8.55 8.08 7.60LB-0360-3-120-38* 3.60 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0370-3-120-38* M 4.5 3.70 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0380-3-120-38* 3.80 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0390-3-120-38* 3.90 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0400-3-120-38 4.00 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0410-3-120-38* 4.10 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0420-3-120-38* M 5 4.20 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0430-3-120-38* 4.30 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0440-3-120-38* 4.40 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0450-3-120-38* 4.50 mm 3 mm 12.0 mm 38 mm 11.00 10.45 9.90 9.35 8.80LB-0460-3-120-38* 4.60 mm 3 mm 12.0 mm 38 mm 13.00 12.35 11.70 11.05 10.40LB-0470-3-120-38* 4.70 mm 3 mm 12.0 mm 38 mm 13.00 12.35 11.70 11.05 10.40LB-0480-3-120-38* 4.80 mm 3 mm 12.0 mm 38 mm 13.00 12.35 11.70 11.05 10.40LB-0490-3-120-38* 4.90 mm 3 mm 12.0 mm 38 mm 13.00 12.35 11.70 11.05 10.40LB-0500-3-120-38 M 6 5.00 mm 3 mm 12.0 mm 38 mm 13.00 12.35 11.70 11.05 10.40LB-0510-3-120-38* 5.10 mm 3 mm 12.0 mm 38 mm 14.50 13.78 13.05 12.33 11.60LB-0520-3-120-38* 5.20 mm 3 mm 12.0 mm 38 mm 14.50 13.78 13.05 12.33 11.60LB-0530-3-120-38* 5.30 mm 3 mm 12.0 mm 38 mm 14.50 13.78 13.05 12.33 11.60LB-0540-3-120-38* 5.40 mm 3 mm 12.0 mm 38 mm 14.50 13.78 13.05 12.33 11.60LB-0550-3-120-38* 5.50 mm 3 mm 12.0 mm 38 mm 14.50 13.78 13.05 12.33 11.60LB-0560-3-120-38* 5.60 mm 3 mm 12.0 mm 38 mm 16.00 15.20 14.40 13.60 12.80LB-0570-3-120-38* 5.70 mm 3 mm 12.0 mm 38 mm 16.00 15.20 14.40 13.60 12.80LB-0580-3-120-38* 5.80 mm 3 mm 12.0 mm 38 mm 16.00 15.20 14.40 13.60 12.80LB-0590-3-120-38* 5.90 mm 3 mm 12.0 mm 38 mm 16.00 15.20 14.40 13.60 12.80LB-0600-3-120-38 6.00 mm 3 mm 12.0 mm 38 mm 16.00 15.20 14.40 13.60 12.80LB-0610-3-120-38* 6.10 mm 3 mm 12.0 mm 38 mm 17.50 16.63 15.75 14.88 14.00LB-0620-3-120-38* 6.20 mm 3 mm 12.0 mm 38 mm 17.50 16.63 15.75 14.88 14.00LB-0630-3-120-38* 6.30 mm 3 mm 12.0 mm 38 mm 17.50 16.63 15.75 14.88 14.00LB-0640-3-120-38* 6.40 mm 3 mm 12.0 mm 38 mm 17.50 16.63 15.75 14.88 14.00LB-0650-3-120-38* 6.50 mm 3 mm 12.0 mm 38 mm 17.50 16.63 15.75 14.88 14.00
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Carbide Tools | Diamond Tools 101
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Drills
L1
D2 D1
L2
Drills with 6 mm shankDescription:A universally applicable drill with a top angle of 130°. Its four-facet grinding with polished radius thinning of the chisel edge reduces the feed force during immersion and enables a very good centring. Due to polished flutes and a polished flute land, the risk of built-up edges and clogging of chips is considerably reduced. If you want to use these drills for pre-drilling threads, please note the suitable thread sizes in the table.
Coating:On request, these drills are also available with an SHC® coating (see page 12).
Fields of application:You can machine a wide range of materials, for instance non-ferrous metals or thermosetting plastics and thermoplastics, but also wood and composites.
Universally applicable drills with a top angle of 130°.
Dimensions and prices
Article no.for
thread
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
130° top angle, short type:KB-0160-6-120-50* M 2 1.60 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0200-6-120-50* 2.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0210-6-120-50* M 2.5 2.10 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0250-6-120-50* M 3 2.50 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0290-6-120-50* M 3.5 2.90 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0300-6-120-50* 3.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0330-6-120-50* M 4 3.30 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0370-6-120-50* M 4.5 3.70 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0400-6-120-50* 4.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0420-6-120-50* M 5 4.20 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0500-6-120-50* M 6 5.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60KB-0600-6-120-50* 6.00 mm 6 mm 12.0 mm 50 mm 17.00 16.15 15.30 14.45 13.60
130° top angle, long type:KB-0300-6-220-60* 3.00 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0310-6-220-60* 3.10 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0320-6-220-60* 3.20 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0330-6-220-60* M 4 3.30 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0340-6-220-60* 3.40 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0350-6-220-60* 3.50 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0360-6-220-60* 3.60 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0370-6-220-60* M 4.5 3.70 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0380-6-220-60* 3.80 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0390-6-220-60* 3.90 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0400-6-220-60* 4.00 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0410-6-220-60* 4.10 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0420-6-220-60* M 5 4.20 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20
...
New
Carbide Tools | Diamond Tools102
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
rills
L1
D2 D1
L2
Plastics
Continuation
Article no.for
thread
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
–20 %20 – 49
KB-0430-6-220-60* 4.30 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0440-6-220-60* 4.40 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0450-6-220-60* 4.50 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0460-6-220-60* 4.60 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0470-6-220-60* 4.70 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0480-6-220-60* 4.80 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0490-6-220-60* 4.90 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0500-6-220-60* M 6 5.00 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0510-6-220-60* 5.10 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0520-6-220-60* 5.20 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0530-6-220-60* 5.30 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0540-6-220-60* 5.40 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0550-6-220-60* 5.50 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0560-6-220-60* 5.60 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0570-6-220-60* 5.70 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0580-6-220-60* 5.80 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0590-6-220-60* 5.90 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20KB-0600-6-220-60* 6.00 mm 6 mm 22.0 mm 60 mm 19.00 18.05 17.10 16.15 15.20
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 50 upwards.
Non-ferr.Metals
WoodCompo-
sites
Carbide Tools | Diamond Tools 103
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Drills
Carbide Tools | Diamond Tools104
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Lances and KnivesFor processing all materials which can be bet-ter cut than milled, we offer different kinds of knives and lances for our cutting heads with a cutting edge length of up to 70 mm.
for oscillating tangential cutting head
for tangential cutting head
for drag knife unit
for universal head
Free delivery at shop.vhf.de
L1
D2
L2
L3
Plastics FoamFoil,
Rubber
LancesDescription:For the oscillating tangential cutting head, you can choose lances with cutting edge lengths from 5 to 70 mm according to your material thickness. The lances are extra thin for cutting also narrow curve radii. Some types have a serrated cutting edge (on the image right). For the tangential cutting head with adjustable spring force, there are lances available with different top angles at considerable shorter lengths.
Fields of application:The lances in the oscillating tangential cutting head are used for processing all kinds of materials which can be better cut than milled, for instance cardboard, softer sandwich materials, foam, etc. The serrated types are especially suitable for insulating materials. The lances in the tangential cutting head are mainly for foils.
Special features:The lances for the tangential cutting heads have a Wel-don slot in order to fix them quickly and only in cutting direction.Lances for the oscillating tangential cutting head.
Dimensions and prices
Article no. Type
D2Shank
diameter
L2Cutting edge
length
L3 L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
Lances for oscillating tangential cutting head:HL-OT-05ES extra thin, single cutting 6 mm 5.0 mm 17 mm 27 mm 28.00 26.60 25.20 23.80HL-OT-07ES* extra thin, single cutting 6 mm 7.0 mm 19 mm 29 mm 31.00 29.45 27.90 26.35HL-OT-10ES extra thin, single cutting 6 mm 10.0 mm 22 mm 32 mm 35.00 33.25 31.50 29.75HL-OT-10ZS* double cutting 6 mm 10.0 mm 22 mm 32 mm 35,00 33,25 31,50 29,75HL-OT-12ES* extra thin, single cutting 6 mm 12.0 mm 24 mm 34 mm 38.00 36.10 34.20 32.30HL-OT-15ES extra thin, single cutting 6 mm 15.0 mm 27 mm 37 mm 42.00 39.90 37.80 35.70HL-OT-17ES* extra thin, single cutting 6 mm 17.0 mm 29 mm 39 mm 45.00 42.75 40.50 38.25HL-OT-20ES extra thin, single cutting 6 mm 20.0 mm 32 mm 42 mm 49.00 46.55 44.10 41.65HL-OT-22ES* extra thin, single cutting 6 mm 22.0 mm 34 mm 44 mm 52.00 49.40 46.80 44.20HL-OT-25ES* extra thin, single cutting 6 mm 25.0 mm 37 mm 47 mm 56.00 53.20 50.40 47.60HL-OT-27ES* extra thin, single cutting 6 mm 27.0 mm 39 mm 49 mm 59.00 56.05 53.10 50.15HL-OT-50 single cutting1 6 mm 50.0 mm 57 mm 65 mm 124.00 117.80 111.60 105.40HL-OT-70 single cutting1 6 mm 70.0 mm 75 mm 83 mm 154.00 146.30 138.60 130.90
Serrated lances for oscillating tangential cutting head:HL-OTS-35* single cutting1 6 mm 35.0 mm 42,5 mm 50 mm 98.00 93.10 88.20 83.30HL-OTS-58* single cutting1 6 mm 58.0 mm 64,5 mm 73 mm 118.00 112.10 106.20 100.30
Lances for tangential cutting head (type with adjustable spring force):HL-T-2.5-55* 55° cutting edge 6 mm 2.5 mm 17 mm 27 mm 28.00 26.60 25.20 23.80HL-T-4.0-45* 45° cutting edge 6 mm 4.0 mm 17 mm 27 mm 28.00 26.60 25.20 23.80HL-T-6.5-30* 30° cutting edge 6 mm 6.5 mm 17 mm 27 mm 28.00 26.60 25.20 23.80
* new tool in this printed issue1 Please note that you can use only lances with a cutting edge length of up to 27 mm in the oscillating tangential cutting head of a multi unit if a milling cutter is chucked in the spindle at the same time.Ask for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
12new
tools
Card-board
Carbide Tools | Diamond Tools106
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esLa
nces
and
K
nive
s
➀
➁ ➂ ➃
Dimensions and prices
KnivesDescription:We offer a standard knife ➀ for replacement in the drag knife unit. For the universal head, there is a wider se-lection of attachments available: a trapeze knife ➁ for the straight cutting attachment with 2 and 5 mm cutting depth. For the older model with 25 mm cutting depth we offer a standing knife ➂. The V-cut knife ➃ for 45° diagonal cutting fits into the various V-cut attachments offered by vhf and will be chucked in different depths there. For the kiss-cut attachment please use the lance with the article number HL-T-2.5-55 which is also offered for the tangential cutting head (see previous page).
Fields of application:The drag knife is especially suitable for cutting lettering foils. The knives in the universal head will be used for di-agonal cutting and straight cuts in materials which do not demand an oscillating knife.
A drag knife and knives for the universal head.
Article no. TypePrice
in €–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
Knife for drag knife unit: HL-SM-STD ➀ standard drag knife 32.00 30.40 28.80 27.20
Knives for universal head: MUK-SC-02* ➁ trapeze knife – for straight cutting attachment, 2 and 5 mm (10 pieces) 5.00 4.75 4.50 4.25MUK-SC-25* ➂ standing knife – for straight cutting attachment, 25 mm (10 pieces) 10.00 9.50 9.00 8.50MUK-VC* ➃ V-cut knife (5 pieces) 59.00 56.05 53.10 50.15
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
3new
tools
Plastics FoamFoil,
RubberCard-board
Carbide Tools | Diamond Tools 107
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Lances and K
nives
Carbide Tools | Diamond Tools108
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Diamond ToolsOur single and double tooth cutters of poly-crystalline diamonds and CVD thick film plates have a very high endurance and can be used without cooling. Additionally we offer polish-ing tools for acrylic glass made of monocrystal-line and polycrystalline diamonds.
All diamond tools are regrindable for several times. The price for the regrinding service depends on the complexity, it usually lies be-tween 80 and 120 euros. Please send us your tools for regrinding individually wrapped.
PCD single tooth cutters
PCD double tooth cutters
MCD polishing cutters
MCD polishing gravers
PCD polishing cutters
PCD polishing gravers
CVD cutters
Free delivery at shop.vhf.de
L1
D2 D1
L2
L3
Non-ferr.Metals
PlasticsWoodCompo-
sites
PCD single tooth cuttersDescription:This single tooth cutter is equipped with a centre-cutting polycrystalline diamond (PCD). This material consists of many single crystals which were sintered at a very high temperature and pressure. It has a very fine granula-tion, is extremely hard and nearly free from abrasion. A PCD tool ensures best surface qualities without ad-ditional cooling. Its endurance is fantastic!
Fields of application:Due to its large flute, the PCD single tooth cutter is espe-cially suitable for working on plastics, which do not tend to smear, softer non-ferrous metals and wood.
Special features:Very long endurance and regrindable for several times.
Diamond single tooth cutters for best surfaces.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
PKD-ES-0300-3-050-0080-40 3.00 mm 3 mm 5.0 mm 8.0 mm 40 mm 125.00 118.75 112.50PKD-ES-0300-3-100-0130-40 3.00 mm 3 mm 10.0 mm 13.0 mm 40 mm 145.00 137.75 130.50PKD-ES-0400-4-080-0110-50 4.00 mm 4 mm 8.0 mm 11.0 mm 50 mm 145.00 137.75 130.50PKD-ES-0400-4-140-0170-50 4.00 mm 4 mm 14.0 mm 17.0 mm 50 mm 165.00 156.75 148.50PKD-ES-0500-6-100-0150-50* 5.00 mm 6 mm 10.0 mm 15.0 mm 50 mm 180.00 171.00 162.00PKD-ES-0600-6-100-0150-50 6.00 mm 6 mm 10.0 mm 15.0 mm 50 mm 180.00 171.00 162.00PKD-ES-0600-6-200-0250-50 6.00 mm 6 mm 20.0 mm 25.0 mm 50 mm 240.00 228.00 216.00PKD-ES-0800-8-100-0150-50 8.00 mm 8 mm 10.0 mm 15.0 mm 50 mm 195.00 185.25 175.50PKD-ES-0800-8-200-0250-60 8.00 mm 8 mm 20.0 mm 25.0 mm 60 mm 295.00 280.25 265.50
* new tool in this printed issuePlease note that the diamond tools are not suitable for the measurement with the automatic z adjustment due to their lacking electric conductivity.You will find a data sheet for setting the operational parameters in the download section of our web site (download.vhf.de).
1new
tool
regrindable
Carbide Tools | Diamond Tools110
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
iam
ond
Tool
s
L1
D2 D1
L2
L3
Non-ferr.Metals
PlasticsWoodCompo-
sitesCeramics,Graphite
PCD double tooth cuttersDescription:The carbide shank of this centre cutting tool is equipped with two cutting plates of polycrystalline diamond (PCD). Due to the extreme hardness and the low wear of the material, you can process non-ferrous metals like alu-minium without cooling. In spite of that you will achieve a fantastic endurance and best surface qualities. Tests in ceramics have shown a more than hundredfold endurance compared with a carbide tool.
Fields of application:The double tooth cutter will be used – depending on its grinding – for aluminium, harder wood, reinforced plastics, ceramics, graphite, composite materials and other highly abrasive materials. By dry processing you work cost-efficiently and your work environment re-mains clean.
Special features:High cutting speed, endurance and regrindable for sev-eral times.
This diamond tool mills aluminium without cooling!
You can use a PCD single tooth cutter when you want to process the materials listed under “Fields of application” with a smaller cutting edge diameter. For technical reasons, it is only possible to realize smaller cutting edge diameters with just one cutting edge. Please take care that you re-adjust the rotational speed and the feed rate accordingly while processing these materials.
Practical Tip
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
PKD-ZS-0500-6-100-0150-50* 5.00 mm 6 mm 10.0 mm 15.0 mm 50 mm 265.00 251.75 238.50PKD-ZS-0600-6-100-0150-50 6.00 mm 6 mm 10.0 mm 15.0 mm 50 mm 265.00 251.75 238.50PKD-ZS-0600-6-200-0250-50 6.00 mm 6 mm 20.0 mm 25.0 mm 50 mm 315.00 299.25 283.50PKD-ZS-0800-8-100-0150-50 8.00 mm 8 mm 10.0 mm 15.0 mm 50 mm 295.00 280.25 265.50PKD-ZS-0800-8-200-0250-60 8.00 mm 8 mm 20.0 mm 25.0 mm 60 mm 395.00 375.25 355.50
* new tool in this printed issuePlease note that the diamond tools are not suitable for the measurement with the automatic z adjustment due to their lacking electric conductivity.By default, the grinding of the diamonds is designed for working on aluminium. If you would like to process other kinds of materials, please tell us them.You will find a data sheet for setting the operational parameters in the download section of our web site (download.vhf.de).
1new
tool
regr
inda
ble
Carbide Tools | Diamond Tools 111
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Diam
ond Tools
L1
D2 D1L2
L3
0,2 mm
Non-ferr.Metals
Plastics
MCD polishing cuttersDescription:The monocrystalline diamond (MCD) which is at-tached to a carbide shank consists of pure carbon and is extremely resistant to wear. Although it has been pro-duced synthetically, it has the same characteristics as a natural diamond. This ultra-hard material ensures glassy polishing edges. It cuts sidewards as well as downwards.
Fields of application:This tool is used for polishing acrylic glass edges and pockets of any contour. A cutting edge or pocket that has been milled is a sufficient preparation. So all kinds of polished acrylic glass letters or logos can be produced quite easily. By default, the grinding of the diamonds is designed for working on plastics, if you would like to pol-ish non-ferrous metals, please ask us.
Special features:Very long endurance and regrindable for several times.
Polishes your acrylic edges and pockets to a high gloss.
You can polish your workpieces in several steps if a fine polishing step does not bother you. For instance you can polish your 10 mm thick material with a cutting edge length of 4 mm in three steps. So you do not have to use a polishing cutter with a cutting edge length of 11 mm which is much more expensive. To achieve best polishing results, do not remove more than 0.05 – 0.07 mm of the material per working cycle.
Practical Tip
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
With edge chamfer 0.15 mm x 45°MKD-PF-0400-4-050-0150-50 4.00 mm 4 mm 5.0 mm 15.0 mm 50 mm 535.00 508.25 481.50MKD-PF-0400-4-060-0150-50 4.00 mm 4 mm 6.0 mm 15.0 mm 50 mm 635.00 603.25 571.50MKD-PF-0400-4-080-0150-50 4.00 mm 4 mm 8.0 mm 15.0 mm 50 mm on requestMKD-PF-0600-6-050-0220-50 6.00 mm 6 mm 5.0 mm 22.0 mm 50 mm 635.00 603.25 571.50MKD-PF-0600-6-060-0220-50 6.00 mm 6 mm 6.0 mm 22.0 mm 50 mm 735.00 698.25 661.50MKD-PF-0600-6-080-0220-50 6.00 mm 6 mm 8.0 mm 22.0 mm 50 mm on request
Please note that the diamond tools are not suitable for the measurement with the automatic z adjustment due to their lacking electric conductivity.You will find a data sheet for setting the operational parameters in the download section of our web site (download.vhf.de).
regrindable
The face photo of the polishing cutter shows that the diamond cutting edge which is soldered to the shank is not centre-cutting. So you have to move slightly in x or y in order to get a perfectly even ground.
Info
Carbide Tools | Diamond Tools112
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
iam
ond
Tool
s
D2
D1L1α
L2
Non-ferr.Metals
Plastics
MCD polishing graversDescription:The diamond of this polishing graver is tapered with angles of 60° and 90°. The monocrystalline diamond (MCD) is extremely resistant to wear and ensures crystal clear engravings.
Fields of application:Using the polishing graver, you polish chamfers or en-gravings in acrylic glass to a high gloss. Up to an im-mersion depth of about 0.5 mm you can engrave directly with this tool, up to the maximum engraving depth of approximately 2 mm you have to preprocess your work-piece with a regular graver. By default, the grinding of the diamonds is designed for working on plastics, if you would like to polish non-ferrous metals, please ask us.
Special features:Very long endurance and regrindable for several times.
Polishes your engravings in acrylic glass to a high gloss.
Dimensions and prices
regr
inda
ble
Article no.
αTop
angle
D1Engraving
width
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
MKD-PS-060-030-4-50 60° 0.30 mm 4 mm 2.0 mm 50 mm 445.00 422.75 400.50MKD-PS-060-030-6-50 60° 0.30 mm 6 mm 2.0 mm 50 mm 445.00 422.75 400.50
MKD-PS-090-030-4-50 90° 0.30 mm 4 mm 2.0 mm 50 mm 445.00 422.75 400.50MKD-PS-090-030-6-50 90° 0.30 mm 6 mm 2.0 mm 50 mm 445.00 422.75 400.50
Please note that the diamond tools are not suitable for the measurement with the automatic z adjustment due to their lacking electric conductivity.You will find a data sheet for setting the operational parameters in the download section of our web site (download.vhf.de).
Carbide Tools | Diamond Tools 113
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Diam
ond Tools
L1
D2 D1
L3
L2
Non-ferr.Metals
Plastics
PCD polishing cuttersDescription:These centre-cutting polishing cutters made of polycrys-talline diamond (PCD) distinguish themselves by their extra long cutting edges. So you can polish also the edges of very thick plates in one cycle without disturbing steps. This becomes possible by using PCD cutting plates instead of the much more expensive monocrystalline dia-mond (MCD) cutting plates which are usually used for polishing. Please see also page 10.
Fields of application:For polishing acrylic glass edges and pockets of any contour. You work with a regular milling cutter as prepa-ration, then you can remove 0.10 – 0.14 mm of the mate-rial per working cycle with this tool.
Special features:Polishing very thick plates in one cycle; regrindable for several times.
Extra long cutting edge – no disturbing steps.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
PKD-PF-0400-6-100-0150-50* 4.00 mm 6 mm 10.0 mm 15.0 mm 50 mm 525,00 498,75 472,50PKD-PF-0600-6-140-0180-50* 6.00 mm 6 mm 14.0 mm 18.0 mm 50 mm 565,00 536,75 508,50PKD-PF-0800-8-180-0220-50* 8.00 mm 8 mm 18.0 mm 22.0 mm 50 mm 605,00 574,75 544,50PKD-PF-1000-10-220-0260-60* 10.00 mm 10 mm 22.0 mm 26.0 mm 60 mm 645,00 612,75 580,50
* new tool in this printed issuePlease note that the diamond tools are not suitable for the measurement with the automatic z adjustment due to their lacking electric conductivity.
New
regrindable
Carbide Tools | Diamond Tools114
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
iam
ond
Tool
s
L1
D2
D1
α
L2
Non-ferr.Metals
Plastics
PCD polishing graversDescription:The diamond of this polishing graver is tapered with an-gles of 60° and 90°. The polycrystalline diamond (PCD) is extremely resistant to wear and can be used – thanks to its great length – for especially deep engravings.
Fields of application:Using the polishing graver, you polish chamfers or en-gravings in acrylic glass or non-ferrous metals to a high gloss. Up to an immersion depth of about 0.1 – 0.2 mm you can engrave directly with this tool, up to the maxi-mum engraving depth of approximately 2.5 mm (90° graver) or 4.5 mm (60° graver) you have to preprocess your workpiece with a regular graver.
Special features:Polishing especially deep engravings; regrindable for several times.
Polish especially deep engravings with PCD cutting edge.
Dimensions and prices New
regr
inda
ble
Article no.
αTop
angle
D1Engraving
width
D2Shank
diameter
L2Cutting edge
length
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
PKD-PS-060-020-6-50* 60º 0.20 mm 6 mm 4.5 mm 50 mm 345.00 327.75 310.50PKD-PS-090-010-6-50* 90º 0.10 mm 6 mm 2.5 mm 50 mm 345.00 327.75 310.50
* new tool in this printed issuePlease note that the diamond tools are not suitable for the measurement with the automatic z adjustment due to their lacking electric conductivity.
Carbide Tools | Diamond Tools 115
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Diam
ond Tools
L2L1
D2 D1
L3
Non-ferr.Metals
WoodCompo-
sites
CVD cuttersDescription:This tool which is centre-cutting has a carbide shank equipped with one or two CVD cutting plates. These CVD thick film plates are built up in thin layers by Chemi-cal Vapour Deposition (CVD). Afterwards they are cut into shape by a laser beam. The result is a very homoge-neous diamond structure and an extremely smooth cutting edge with which you will achieve highest sur-face qualities. Compared with the already very good re-sults of PCD tools, the CVD tools distinguish themselves by an even greater hardness and resistance to wear which can lead to an even longer endurance.
Fields of application:CVD milling cutters are ideal for abrasive materials like GRP/CRP, harder non-ferrous metals and their alloys (e.g. AlSi), graphite, wood, ...
Special features:Especially long endurance and regrindable for several times.
Extremely hard cutting plates – for abrasive materials.
Dimensions and prices
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L3
Undercut
L1Total
length
Pricein €
–5 %2 – 4
–10 %5 – 9
CVD single tooth cutters: CVD-ES-0300-6-050-0100-50* 3.00 mm 6 mm 5.0 mm 10.0 mm 50 mm 255.00 242.25 229.50
CVD double tooth cutters:CVD-ZS-0400-6-060-0120-50* 4.00 mm 6 mm 6.0 mm 12.0 mm 50 mm 335.00 318.25 301.50CVD-ZS-0600-6-100-0140-50* 6.00 mm 6 mm 10.0 mm 14.0 mm 50 mm 375.00 356.25 337.50CVD-ZS-0800-8-120-0160-50* 8.00 mm 8 mm 12.0 mm 16.0 mm 50 mm 425.00 403.75 382.50CVD-ZS-1000-10-080-0180-60* 10.00 mm 10 mm 8.0 mm 18.0 mm 60 mm 425.00 403.75 382.50
* new tool in this printed issuePlease note that the diamond tools are not suitable for the measurement with the automatic z adjustment due to their lacking electric conductivity.
New
regrindable
Ceramics,Graphite
Carbide Tools | Diamond Tools116
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esD
iam
ond
Tool
s
Impression ToolsThese tools are equipped with appropriate shanks and stop rings for use in the milling ma-chines of the vhf Impression line.
You will find here a selection of tools from the vhf product range which are suitable for typical goldsmith works in materials like wax, plastics and metal.
Gravers with top radius
Single tooth cutters Varius®
Single tooth cutters with polished flute
Single tooth cutters with undercut
Radius cutters with undercut
Double tooth cutters with fishtail
Double tooth cutters with face radius
Free delivery at shop.vhf.de
L1L2
D2 D1L3L4
Goldsmith toolsDescription:This category contains a selection of different tool types from the vhf product range, namely gravers, sin-gle tooth cutters, double tooth cutters and radius cutters. They are based on the appropriate vhf standard tools. A nearer description of these tools can be found there. All goldsmith tools already have a stop ring and a total length of 35 mm for using them in the machines of the Impression line. Their chucking depth (L4) is 11 mm.
Fields of application:For typical goldsmith works in materials like wax, plastics and metal.
Please note:If you want to use other vhf tools with a 3 mm shank in your Impression machine, we would be glad to equip them for a surcharge of € 2 with an appropriate stop ring.
Tools which are suitable for typical goldsmith works.
Dimensions and prices New
Non-ferr.Metals
Plastics Wax
Article no.
D1Cutting edge
diameter
D2Shank
diameter
L2Cutting edge
length
L1Total
length RemarksPrice
in €–5 %2 – 4
–10 %5 – 9
–15 %10 – 19
Graver with 15° top angle and face radius GSW-GS-R-015-010-3-35* 3 mm 35 mm radius: 0.05 mm 15.00 14.25 13.50 12.75
Single tooth cutters Varius® GSW-ES-SC-100-3-050-35* 1.00 mm 3 mm 5.0 mm 35 mm 19.00 18.05 17.10 16.15GSW-ES-SC-200-3-080-35* 2.00 mm 3 mm 8.0 mm 35 mm 19.00 18.05 17.10 16.15GSW-ES-SC-300-3-100-35* 3.00 mm 3 mm 10.0 mm 35 mm 16.00 15.20 14.40 13.60
Single tooth cutters with polished fluteGSW-ES-PS-300-3-120-35* 3.00 mm 3 mm 12.0 mm 35 mm 20.00 19.00 18.00 17.00
Single tooth cutter with undercutGSW-ES-FS-150-3-050-13-35* 1.50 mm 3 mm 5.0 mm 35 mm undercut (L3): 13 mm 24.00 22.80 21.60 20.40
Single tooth cutter with face radiusGSW-ES-SCR-200-3-080-16-35* 2.00 mm 3 mm 8.0 mm 35 mm undercut (L3): 16 mm 25.00 23.75 22.50 21.25
Radius cutters with undercutGSW-RF-040-3-008-5-35* 0.40 mm 3 mm 0.8 mm 35 mm undercut (L3): 5 mm 30.00 28.50 27.00 25.50GSW-RF-080-3-016-9-35* 0.80 mm 3 mm 1.6 mm 35 mm undercut (L3): 9 mm 30.00 28.50 27.00 25.50GSW-RF-300-3-100-16-35* 3.00 mm 3 mm 10.0 mm 35 mm undercut (L3): 16 mm 25.00 23.75 22.50 21.25
Double tooth cutters with fishtailGSW-ZS-FS-050-3-030-35* 0.50 mm 3 mm 3.0 mm 35 mm 10.50 9.98 9.45 8.93GSW-ZS-FS-100-3-050-35* 1.00 mm 3 mm 5.0 mm 35 mm 10.50 9.98 9.45 8.93GSW-ZS-FS-200-3-090-35* 2.00 mm 3 mm 9.0 mm 35 mm 10.50 9.98 9.45 8.93GSW-ZS-FS-300-3-120-35* 3.00 mm 3 mm 12.0 mm 35 mm 10.50 9.98 9.45 8.93
Double tooth cutters with face radiusGSW-ZS-SCR-100-3-050-35* 1.00 mm 3 mm 5.0 mm 35 mm face radius: 0.5 mm 20.00 19.00 18.00 17.00GSW-ZS-SCR-200-3-090-35* 2.00 mm 3 mm 9.0 mm 35 mm face radius: 1.0 mm 20.00 19.00 18.00 17.00GSW-ZS-SCR-300-3-120-35* 3.00 mm 3 mm 12.0 mm 35 mm face radius: 1.5 mm 20.00 19.00 18.00 17.00
* new tool in this printed issueAsk for an individual offer if you are interested in annual orders or single orders of quantities from 20 upwards.
Carbide Tools | Diamond Tools118
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esIm
pres
sion
To
ols
AccessoriesIn this section you will find vacuum fleece and adhesive film, stop rings for your tools and reducing bushes for clamping smaller tools in larger collet chucks as well as coolants and lubricants.
Accessory parts and expendable items which depend on your milling machine and its equip-ment (for instance on the spindle or the fixing devices) can be found in our machine cata-logue.
Vacuum fleece
Special adhesive film
Stop rings
Reducing bushes
Coolants and lubricants
Free delivery at shop.vhf.de
DX 2
DX 1
Stop rings
Special adhesive film
Vacuum fleece
■ This especially thin (80 µm thickness) and plane film is used for fixing workpieces directly on the polystyrene surface or a similar surface. The film can be easily and completely removed after use.
Description Article no. PriceSpecial adhesive film DX 1, 25 m x 50 cm
regular adhesive force ET-XF-DX1 € 135.00Special adhesive film DX 2, 25 m x 50 cm
double adhesive force ET-XF-DX2 € 135.00
Scale of quantity discount: ≥ 2 units 5 %, ≥ 5 units 10 %, ≥ 10 units 15 %
■ The vacuum fleece is made of a special, foamed material which is permeable to air. Your workpieces will still be fixed safely even if some areas of the table remain uncovered. The extra thin type with a thickness of 1 mm distinguishes itself by an especially great holding force and is particularly suitable for machining smaller workpieces. The other type with a thickness of 2 mm is characterized by a longer durability and is ideal for almost any case. The vhf vacuum fleece can also be used for vacuum clamping systems of other manufacturers (e.g. on the basis of MDF boards). It often leads to significant im-provements regarding the holding force.
Description Article no. PriceVacuum fleece from the roll, charged per linear metre:
• 1 mm thickness, 1 m width ET-SV-VV-01-R1 € 12.00• 2 mm thickness, 0.5 m width ET-SV-VV-02-R05 € 9.00• 2 mm thickness, 1 m width ET-SV-VV-02-R1 € 18.00
Vacuum fleece, cut into squares:• 2 mm thickness, 500 x 500 mm packaging unit 5 pieces ET-SV-VV-02-05 € 34.00
Scale of quantity discount: ≥ 2 linear metres/packaging units 5 %, ≥ 10 linear metres/packaging units 10 %, ≥ 15 linear metres/packaging units 15 %, ≥ 30 linear metres/packaging units 25 %
■ The stop rings made of brass are designed for the receptacles of a high frequency spindle tool changer, the plastic stop rings are suit-able for changing the tools manually. You can equip those tools with stop rings by yourself which are not already delivered with a ring.
Material: plastics (AR-300K) respectively brass (AR-...N)
Int. Ø Ext. Ø Height PU Article no. Price3 mm 7.7 mm 4.85 mm 20 pcs. AR-300K € 2.003 mm 10.6 mm 6.5 mm 5 pcs. AR-300N € 9.004 mm 10.6 mm 6.5 mm 5 pcs. AR-400N € 9.005 mm 10.6 mm 6.5 mm 5 pcs. AR-500N € 9.006 mm 10.6 mm 6.5 mm 5 pcs. AR-600N € 9.00
■ Using our ringing set, you can equip your 3 mm, 4 mm and 6 mm tools with stop rings by yourself. The set consists of a ringing plate and a steel pin punch. You will need nothing more, but a little ham-mer.
Description Article no. PriceRinging set with pin punch AR-BP-SET € 9.50
Scale of quantity discount: ≥ 2 packaging units/pieces 5 %, ≥ 5 packaging units/pieces 10 %, ≥ 10 packaging units/pieces 15 %
Carbide Tools | Diamond Tools120
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
esA
cces
sori
es
Description Spindle accessories for all vhf spindles • collet chucks • cap nuts • jaw hook and pin wrenches • cones • tool fittings for automatic tool changer • service set for collet chuck maintenance
Fixing devices • fixation bars • hand lever clamping devices • clamps • pneumatic clamping device • vises • polystyrene stripes, self-adhesive • vacuum suction units • vacuum adaptor mats
Miscellaneous • vacuum cleaner accessories (suction shoes, filter bags, ...) • slide nuts for the T-slots of the machine table • lubricants • cleaners • switching unit for workflow automatisation • 3-D measuring sensor
More articles in the machine catalogue
Coolants and lubricants
■ If you use a special cooling lubricant for milling or engraving, you will achieve better results and the tool life will be extended. For some kinds of materials it is even absolutely necessary to use a cooling lu-bricant.
Description Article no. PriceSpray lubricant AquaTec® (1 litre)
for milling, drilling, cutting steel; for usage in the cooling and spraying unit; water soluble, concentration 6 – 7 % ET-MK-AT € 12.00
Spray lubricant ALU-N (1 litre)for milling, cutting, sawing non-ferrous metals and steel; for usage in the cool-ing and spraying unit ET-MK-ALUN € 7.50
Special lubricant WST 20 (1 litre)for working on non-ferrous metals and steel; only for usage in the minimum quantity lubrication unit ET-MK-WST20 € 24.00
Cutting oil spray Alpha 93 (300 ml)universal cutting oil from a pressurised dispenser; for all types of steel ET-MK-AL93 € 10.00
Scale of quantity discount: ≥ 5 litres/cans 10 %, ≥ 10 litres/cans 15 %, ≥ 20 litres/cans 20 %
Reducing bushes
■ Reducing bushes are used to clamp tools with a smaller shank dia-meter into a larger collet chuck. So it becomes for instance possible to clamp a tool with a shank diameter of 4 mm into a collet chuck with a diameter of 6 mm when you use the reducing bush RH-46.
Intern. Ø Extern. Ø Length Article no. Price3 mm 6 mm 20 mm RH-36 € 16.004 mm 6 mm 20 mm RH-46 € 16.00
Scale of quantity discount: ≥ 2 pieces 5 %, ≥ 5 pieces 10 %, ≥ 10 pieces 15 %
Carbide Tools | Diamond Tools 121
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
Accessories
Hints for the right number of teethIn which case it is best that a milling cutter has as few teeth as possible...The main problem of milling slots is the agglomeration of chips on the cutting edge which may lead to a plugged milling cutter. When a milling cutter is finally plugged, it can no longer trans-port the chips, and the feeding force of the milling machine will break it. Usually this happens – depending on the material – long before the cutting edge is worn out. So, primarily the ques-tion whereto the chips should be discharged has to be solved. Usually this will be done upwards or to the back. However, the flute should be as large as possible to transport the chips past the substance of the milling cutter. A comparison of the cross-sections of different types clearly shows that the single tooth cutter has the greatest open space (= size of the flute). This leads to the lowest risk of plugging. The more cutting edges a milling cutter has, the more the open space is being reduced. The less cutting edges a milling cutter has – and the more tapered they are –, the easier it is to dip into the surface of the workpiece.
For working on materials which are mainly used for sign making like plastics (PVC, acrylic glass, rigid foam, etc.) and non-ferrous metals (soft aluminium, aluminium composite plates, soft brass alloys, ...), the single tooth cutter is usually better. The cutting edge erosion is less strong here than the risk of plugging.
In which case it is best that a milling cutter has as many teeth as possible...The cutting edge is the wearing part of the milling cutter. The more cutting edges a milling cut-ter has, the more cutting edges share the wear. So the endurance, the life-time, of the tool will be prolonged. A milling cutter with more cutting edges has a better true running accuracy than with only one cutting edge. The more cutting edges a tool has, the smaller become the chips. This leads to smoother surfaces.
A double tooth cutter is recommended when you are working on thermosetting plastics or harder sorts of aluminium (short-chipping).
We recommend multi-tooth cutters for very hard non-ferrous metals (very hard aluminium alloys, brass, ...) and for ferrous material. Usually, they are also well suitable for finishing opera-tions.
Cross-section of single tooth cutter: It has a great open space.
Cross-section of triple tooth cutter: Three cut-ting edges need much more space.
Tips for the proper use of toolsAlways choose a milling cutter which is suitable for the material which you process. Please notice our extensive descriptions of the tools and their fields of application in this catalogue. Withstand the temptation to use a tool which you have at your fingertips incidentally. The tool should be as short as possible and be clamped as deep as possible into the collet chuck.
If your material should not be listed, please classify it according to its machinability (hardness). When working on brass for instance, you should rather orient on the parameters of aluminium than on those of stainless steel, whereas when working on construction steel, you should rather orient on stainless steel than on aluminium.
You can also use the opportunity of our personal tool advisory service from our experts under +49 (0) 7032 97097-430 respectively [email protected]. If we should give you advice concerning the machining parameters, please provide us with the following information: type of the material (with data sheet, where necessary), the maximum thickness which you want to process, your in-tended shank and cutting edge diameter and some basic information concerning your machine (manufacturer and model, rotational speed of the spindle and its power, how do you fix the workpieces?). If you have already machined this kind of material, which tool do you use currently and what are your parameter settings? Finally, what are possible problems?
Wood
etc.
Plastics
Non-ferr.Metals
Ferrous Metals
Foam
Carbide Tools | Diamond Tools122
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
Setting the machining parametersIn order to set the optimal values for lowering speed, immersion depth, feed rate and rotational speed, a number of factors are important:
■ what material is the workpiece made of ■ how is the workpiece fixed ■ type of coolant/lubricant ■ power/maximum rotational speed of the spindle ■ minimum/maximum feed rate of the CAM system ■ stiffness of the machine
As there is a large number of parameters which influence each other, it is not possible to provide you with generalities con-cerning the machining parameters. Instead we would like to give you miscellaneous directions which points deserve closer attention. In any case you have to observe all safety and protective regulations of the machine. When you set the opera-tional parameters, you should approach from the safe side, so you should choose at first for most materials a lower lowering speed, immersion depth and feed rate – but keep up the rotational speed. During the milling process, you can further op-timise the results by carefully changing the parameters. When machining plastics, please note that feed rates and rotational speeds which are too slow may lead to a melting of the material.
The immersion depth depends on the power of your spindle, i. e. only if your spindle has a sufficient power reserve, you may actually set the maximum immersion depth. In case of doubt: When you mill deeper slots it is better to remove in more steps less material than too much at once. Usually, it is also more eco-nomic to mill a slot in several steps with less immersion depth and at higher rates of feed than at once and accordingly slower. General guidelines for the relationship of immersion depth and cutting edge diameter: rigid foam up to 5-fold diameter plastics (acrylic glass, etc.) up to 2-fold diameter aluminium up to 0.5-fold diameter steel up to 0.3-fold diameter stainless steel up to 0.2-fold diameter
Please observe also the load display of the spindle controller, especially when you are working with bigger tool diameters on difficult to machine materials like stainless steel. It should not exceed a load of 80 %, if possible. So you should approach the specified immersion depth only stepwise and always watch your spindle load.
Choice of the milling directionContrary to the circumstances on heavy machining centres, the quality of both edges of the milled slot will never be exactly the same when you work on lighter milling machines. While milling in the counter direction, the tool moves – relatively regarded – against the material. The chip size becomes increasingly big-ger towards the middle. While milling in the same direction, the tool moves with the material; the chip size is reduced again until the exit of the cutting edge from the material. The cutting edge runs in the counter direction as well as in most parts of the same direction against massive material. However, immediately before the exit, there is not much material left. So the last bit will often be rather torn off instead of being cleanly cut. Therefore the counter direction becomes smoother than the same direc-tion. However, this effect varies strongly with the characteristics of the material, the geometry and sharpness of the milling cut-ter and the machining parameters. Thus we recommend to mill internal contours clockwise and external contours counter-clockwise.
worse cutting edge
better cutting edgerela
tive
nate
rial m
ovem
ent
chip
siz
e
same direction
counter direction
cutter direction
Rigi
d fo
am
Plas
tic
Non
-ferr
ous
met
al
Stai
nles
s st
eel
Schematic illustration of the immersion depth into different kinds of materials – from rigid foam over plastics and aluminium up to stainless steel. With increasing hardness of the material, the spiral of the flute becomes flatter and the cutting edge becomes shorter.
Carbide Tools | Diamond Tools 123
Milling
Cutters
Deburring Tools
Router BitsThread C
uttersD
rillsLances and
Knives
Diam
ond Tools
Impression Tools
Accessories
Engraving Tools
What to do in case of problems?
■ If especially plastics should melt, the reason may be that the tool advances too slow and produces too much heat. Please re-duce the rotational speed and increase the feed rate at the same time.
■ If a milling cutter should become plugged, usually the chips have not been discharged quick enough. In such a case, the im-mersion depth and/or the feed rate have to be reduced. It may also help to use a different tool. Please note the hints on the number of cutting edges of milling cutters on page 122.
■ When working on critical materials like extruded acrylic glass, milling cutters with polished flute have proven to be well suit-able. Here the chips can hardly stick to the cutting edge.
■ In case of a burr formation, you should increase the cooling. It could possibly become necessary to make also an addition-al finishing pass. Another possibility would be to increase the feed rate and to reduce rotational speed and removal rate at the same time.
■ If a tool breaks rather frequently, the removal rate is too high or the true running of the spindle is not exact enough. Please reduce in such a case the feed rate and/or the immersion depth and exchange the collet chuck for test reasons.
■ In case that your controller does not have a look-ahead function (point-to-point or look-ahead of just one vector), you should stay below the calculated maximum feed rate, especially when performing fine engraving works. For instance, if you engrave small fonts which consist of numerous little vectors, the machine always has to accelerate and slow down strongly again. Even if the controller calculates one vector in advance (e. g. vhf CNC 450), it cannot accelerate in a curve to maximum speed because each next but one vector will be “in the dark”. You have a similar situation when you drive with your car in the fog, when you can only see from one guiding pole to the next. So an optimum velocity along the path (as is the case with CNC 550 – 980) can not be achieved. The bearings of the machine and the tool will be exposed to strong forces due to the strong acceleration and brake applications. On top of that, the machine can “overshoot” due to the mass inertia. This effect becomes obvious in a bucking of the machine which leads to results that are worse on the whole. The speed advantage can be neglected. Please interrupt the output process as soon as the machine starts bucking and restart it at reduced speed.
■ If your system permits only lower rates of feed than it would be possible according to tool and material data (please note also the above-mentioned remarks concerning fine engraving works), you should reduce feed rate and rotational speed accordingly.
Cooling/lubricationFor working on most kinds of materials it is necessary – or at least recommended – to cool the cutting edge of the tool with air or lubricant. This improves the surface quality and prolongs the endurance of the tool.
If cooling is not possible, the recommended minimum values for rotational speed should be adhered to; the feed rate, however, should not be set too slow. In this case, the heat dissipation will be made by the chips, otherwise you will risk that the material scorches.
Recommended coolants/lubricants (see page 121):Plastics/acrylic glass: dry processing with chip extraction or cooling with compressed air.
Aluminium: spray lubricant ALU-N or minimum quantity lubri-cant WST 20.
Steel/stainless steel: emulsion of spray lubricant AquaTec® and water or minimum quantity lubricant WST 20. For manual ap-plication also cutting oil spray Alpha 93.
Carbide Tools | Diamond Tools124
Mill
ing
C
utte
rsEn
grav
ing
Tool
sD
ebur
ring
To
ols
Rout
er B
itsTh
read
C
utte
rsD
rills
Lanc
es a
nd
Kni
ves
Dia
mon
d To
ols
Impr
essi
on
Tool
sA
cces
sori
es
CNC Milling Machines
> 25 years vhf
Request your catalogue!Highly precise, robust and quick – milling machines Made in Germany
vhf camfacture AGLettenstraße 1072119 Ammerbuch/GermanyPhone +49 (0) 7032 97097-000Fax +49 (0) 7032 97097-900Internet www.vhf.deE-Mail [email protected]