Upload File

cli router cisco rule #5

prev
next
out of 6
Download CLI Router Cisco Rule #5

Upload: ragman-fache

Post on 04-Apr-2018

212 views

Category:

Documents


0 download

Report

TRANSCRIPT

  • 7/30/2019 CLI Router Cisco Rule #5

    1/6

    STEP 1, Create topology base on picture

    Router0

    interface

    fa0/0-----> IP:10.0.0.1/8

    se2/0-----> IP:20.0.0.1/8

    se3/0-----> IP:40.0.0.1/8

    Router1

    interface

    fa0/0-----> IP:30.0.0.1/8

    se2/0-----> IP:20.0.0.2/8

    se3/0-----> IP:50.0.0.1/8

    Router3

    interface

    fa0/0-----> IP:60.0.0.1/8

    se2/0-----> IP:40.0.0.2/8

    se3/0-----> IP:50.0.0.2/8

    STEP 2, consoling via PC0 (take over Routr0)

    Router0>enable

  • 7/30/2019 CLI Router Cisco Rule #5

    2/6

    Router0#configure terminal

    Router0(config)#interface Fastethernet0/0

    Router0(config-if)#ip address 10.0.0.1 255.0.0.0

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

    Router0(config)#interface Serial2/0

    Router0(config-if)#ip address 20.0.0.1 255.0.0.0

    Router0(config-if)#clock rate 64000

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

    Router0(config)#interface Serial3/0

    Router0(config-if)#ip address 40.0.0.1 255.0.0.0

    Router0(config-if)#clock rate 64000

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

    Router0(config)#enable password one

    Router0(config)#

    STEP 3, consoling via Laptop0 (take over Router1)

    Router0>enable

    Router0#configure terminal

    Router0(config)#interface Fastethernet0/0

    Router0(config-if)#ip address 30.0.0.1 255.0.0.0

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

  • 7/30/2019 CLI Router Cisco Rule #5

    3/6

    Router0(config)#interface Serial2/0

    Router0(config-if)#ip address 20.0.0.2 255.0.0.0

    Router0(config-if)#clock rate 64000

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

    Router0(config)#interface Serial3/0

    Router0(config-if)#ip address 50.0.0.1 255.0.0.0

    Router0(config-if)#clock rate 64000

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

    Router0(config)#enable password two

    Router0(config)#

    STEP 4, consoling via Laptop1 (take over Router3)

    Router0>enable

    Router0#configure terminal

    Router0(config)#interface Fastethernet0/0

    Router0(config-if)#ip address 60.0.0.1 255.0.0.0

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

    Router0(config)#interface Serial2/0

    Router0(config-if)#ip address 40.0.0.2 255.0.0.0

    Router0(config-if)#clock rate 64000

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

  • 7/30/2019 CLI Router Cisco Rule #5

    4/6

    Router0(config)#interface Serial3/0

    Router0(config-if)#ip address 50.0.0.2 255.0.0.0

    Router0(config-if)#clock rate 64000

    Router0(config-if)#no shutdown

    Router0(config-if)#exit

    Router0(config)#

    Router0(config)#enable password three

    Router0(config)#

    STEP 5, static IP for Router0

    Router0(config)#ip route 30.0.0.0 255.0.0.0 20.0.0.2

    Router0(config)#ip route 50.0.0.0 255.0.0.0 20.0.0.2

    Router0(config)#ip route 60.0.0.0 255.0.0.0 20.0.0.2

    Router0(config)#ip route 30.0.0.0 255.0.0.0 40.0.0.2

    Router0(config)#ip route 50.0.0.0 255.0.0.0 40.0.0.2

    Router0(config)#ip route 60.0.0.0 255.0.0.0 40.0.0.2

    STEP 6, static IP for Router1

    Router1(config)#ip route 10.0.0.0 255.0.0.0 20.0.0.1

    Router1(config)#ip route 40.0.0.0 255.0.0.0 20.0.0.1

    Router1(config)#ip route 60.0.0.0 255.0.0.0 20.0.0.1

    Router1(config)#ip route 10.0.0.0 255.0.0.0 50.0.0.2

    Router1(config)#ip route 40.0.0.0 255.0.0.0 50.0.0.2

    Router1(config)#ip route 60.0.0.0 255.0.0.0 50.0.0.2

    STEP 7, static IP for Router3

    Router3(config)#ip route 10.0.0.0 255.0.0.0 30.0.0.1

    Router3(config)#ip route 20.0.0.0 255.0.0.0 30.0.0.1

    Router3(config)#ip route 30.0.0.0 255.0.0.0 30.0.0.1

  • 7/30/2019 CLI Router Cisco Rule #5

    5/6

    Router3(config)#ip route 10.0.0.0 255.0.0.0 40.0.0.1

    Router3(config)#ip route 20.0.0.0 255.0.0.0 40.0.0.1

    Router3(config)#ip route 30.0.0.0 255.0.0.0 40.0.0.1

    STEP 8, Setting IP user

    PC0 (10.0.0.2/8) , Laptop0 (30.0.0.2/8) , Laptop1 (60.0.0.2/8)

    STEP 9, ping all node (make sure all node connected)

    STEP 10, Giving telnet service

    at Router0 side

    Router0(config)#line vty 0 4

    Router0(config-line)# password 121212

    Router0(config-line)# login

    Router0(config-line)# exit

    Router0(config)#

    at Router1 side

    Router1(config)#line vty 0 4

    Router1(config-line)# password 123123

    Router1(config-line)# login

    Router1(config-line)# exit

    Router1(config)#

    at Router3 side

    Router3(config)#line vty 0 4

    Router3(config-line)# password 112233

    Router3(config-line)# login

    Router3(config-line)# exit

    Router3(config)#

  • 7/30/2019 CLI Router Cisco Rule #5

    6/6

    STEP 11, DHCP setting

    Router1 ---> Setting IP Fastethernet1/0 (70.0.0.1/8)

    Add LAN with two PCs into Router1 (fastethernet1/0)

    Router1(config)#ip dhcp pool auto ----------------------> word "auto" is option

    Router1(dhcp-config)#network 70.0.0.0 255.0.0.0

    Router1(dhcp-config)#default-router 70.0.0.1

    Router1(dhcp-config)#dns-server 70.0.0.100 -------------> IP option, base on DNS on your LAN


Moxa Industrial Secure Router CLI Command Set … summer-time Use the clock summer -time global configuration command on the router to enable the day light savi ng time offset and

CLI Router

TL-ER5120 Gigabit Load Balance Broadband Router how to log in and set up the Router using CLI commands by console port. -3- Appendix A Hardware Specifications Lists the hardware specifications

Dgw v2.0 Application - VoIPon Solutions · Configuring the CLI ... DHCPv4 Classless Static Route Option ... Outbound Proxy Loose Router Configuration

OfficeConnectTM Remote 812 ADSL Router CLI User’s · PDF file · 2017-11-23 ® OfficeConnectTM Remote 812 ADSL Router CLI User’s Guide Release 1.0. ii 3Com Corporation 5400 Bayfront

SEFOS CLI Reference Manual, Volume 7 · 2015. 8. 14. · 8 Sun Ethernet Fabric Operating System CLI Reference Manual, Vol. 7 August 2015 45.1 ipv6 mld router Command Objective This

Configuring a Router. Router user interface The Cisco IOS software uses a command-line interface (CLI) as the traditional console environment. This environment

CCNA Cisco CLI Command Line for Cisco Router and Switch

Konfigurasi Dasar Router Menggunakan CLI satu cara konfigurasi pada router cisco adalah menggunakan CLI ... Lacak rute Web Server menggunakan perintah tracert pada Commant Prompt di

Solwise Ltd · Solwise Ltd. CLI Command instructions for Solwise SAR110 ADSL Router Please Note: Incorrect usage of CLI commands can seriously damage the firmware settings and

Moxa Industrial Secure Router CLI Command Set User’s Manual · CLI Command Set User's Manual System Functions 1-4 System Information hostname To specify or modify the host name

CCENT - · PDF fileCCENT Course Outline Chapter 3: The Cisco Router and Switch Interface - Cisco IOS - Cisco CLI - Administrative Functions - Configuring Interfaces

telecom.iu.edu · Web viewRequirement to review firewall and router rule sets at least every six months Build firewall and router configurations that restrict connections between

Dual SIM Industrial Cellular VPN Router For · PDF fileDual SIM Industrial Cellular VPN Router For GPRS/EDGE/UMTS/HSPA+/4G LTE Networks ... 5.2 How to Configure the CLI ... 5.3 Commands

Sizing Router Buffers€¦ · How much Buffer does a Router need? § Universally applied rule-of-thumb: § A router needs a buffer size: § 2T is the two-way propagation delay (or

7450 ETHERNET SERVICE SWITCH 7750 SERVICE … · 7950 EXTENSIBLE ROUTING SYSTEM VIRTUALIZED SERVICE ROUTER ... 2.2 RIPng ... 2.6 Configuring RIP with CLI

Cisco 1900 Series Integrated Services Router Hardware ...nhprice.com/downloads/1940_HIG.pdfContents vi Cisco 1900 Series Hardware Installation Using the Cisco CLI—Manual Configuration

Router CLI

CLI Command Reference - eu.dlink.com · Router Discovery Protocol Commands ... a basic knowledge of Ethernet and networking concepts. ... and configuring the switch

Mediant MSBR IP Networking CLI Configuration Guide Ver. 6 · 5.2.1.2 Default Zone ... 21.5.2 Configuring Stateful DHCP ..... 136 21.5.3 Configuring Router Advertisement ... Added

WANs and Router Basics Semester 2 Chapter 2: WANs & Routers Chapter 3: Router CLI By: Allan Johnson

System CLI Show CLI

EdgeRouter Lite 3-Port Router - Ubiquiti Networks · PDF fileEdgeRouter Lite 3-Port Router Model: ERLite-3 ... and shell commands • CLI access through the serial console port, SSH,

INITIALE... · rezultate initiale definitivat 2017 cod cl1121 cli 032 cl1127 cl1015 cl1016 cli 021 cl1010 cl1019 cl1005 cli cli cliooi cl1020 cli 130 cl1004 clioii cli cl1115 cli

HP Switch Software Comware CLI Commands in ProVision ... CLI Commands in... · displayospfv3peerpeer-router-id.....213 FieldDescriptions ... commands,syntax,andoperations

Engineering Workshops Router Configuration. Engineering Workshops Cisco Router Configuration Rule #1: What Would v4 do? –Enable routing ipv6 unicast-routing

CLI User Manual 3G/4G Routerimg.hongdian.com/UploadFiles/Files/Product_Manual/Router...Doc. Version 1.2 iii 3G/4G Router CLI User Manual Foreword Overview This document describes Hongdian

CLI Tips, Techniques, and Shortcuts - · PDF file6-140 Cisco IOS XR Getting Started Guide for the Cisco CRS-1 Router OL-24754-01 Chapter 6 CLI Tips, Techniques, and Shortcuts CLI Tips

Engineering Workshops 92 Router Configuration. Engineering Workshops 93 Cisco Router Configuration Rule #1: What would v4 do? –Enable routing ipv6 unicast-routing

Ethernet Interface Commands on the Cisco ASR 9000 Series ... · Ethernet Interface Commands on the Cisco ASR 9000 Series Router Thismoduleprovidescommandlineinterface(CLI)commandsforconfiguringEthernetinterfacesonthe

BCM50a Integrated Router Configuration — Basics€¦ · Nortel Contivity Client Termination ... Configuring Contivity Client VPN Rule Setup ... BCM50a Integrated Router Configuration

Router Dan CLI

1 Pertemuan 5 Configuring a Router. Discussion Topics CLI command modes Configuring a router name Configuring router passwords Examining the show commands

CLI Commands - Cisco - Global Home Page...CLI Commands TheCiscoWirelessLANsolutioncommand-lineinterface(CLI)enablesoperatorstoconnectanASCII

cloud-systems-managem - California State University, Los ...cs3.calstatela.edu/~egean/cs581/cisco-asa5505-firewall/IPsec-vpn... · Router CLI Configuration Verify ... Perform these