clevis hanger

OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330CUSTOMER SERVICE • 800.786.5266

www.tolco.com14

www.tolco.comRevision 10/24/2007

Fig. 1 - Standard Clevis Hanger

Dimensions • Weights

Pipe Rod Size A Max. Rec. Approx.

Size STD NFPA B C D Load Lbs. Wt./100

1/2 3/8 3/8 21⁄16 13⁄16 1 610 36 3/4 3/8 3/8 27⁄8 17⁄8 1 610 38 1 3/8 3/8 31⁄4 21⁄16 1 610 42

11⁄4 3/8 3/8 39⁄16 21⁄4 1 610 46 11⁄2 3/8 3/8 37⁄8 23⁄8 1 610 49 2 3/8 3/8 47⁄16 23⁄4 1 610 55

21⁄2 1/2 3/8 55⁄16 31⁄4 1 1130 124 3 1/2 3/8 515⁄16 31⁄2 11⁄4 1130 140 31⁄2 1/2 3/8 67⁄16 33⁄4 11⁄4 1130 152

4 5/8 3/8 73⁄8 41⁄4 11⁄2 1430 190 5 5/8 1/2 815⁄16 51⁄4 11⁄2 1430 235 6 3/4 1/2 913⁄16 51⁄2 11⁄2 1940 317

8 3/4 1/2 129⁄16 71⁄8 2 2000 428 10 7/8 5/8 161⁄4 95⁄8 31⁄4 3600 918 12 7/8 5/8 189⁄16 1013⁄16 31⁄8 3800 1086

14 1 — 203⁄4 123⁄8 4 4200 1267 16 1 — 227⁄8 133⁄16 33⁄4 4600 1930 18 1 — 253⁄4 159⁄32 47⁄16 4800 2264

20 11⁄4 — 2813⁄16 171⁄16 53⁄16 4800 3531 *24 11⁄4 — 321⁄8 181⁄4 47⁄16 4800 4431 *30 11⁄4 — 387⁄8 217⁄8 5 6000 6940 *36 11⁄2 — 48 273⁄4 53⁄4 9500 18103

*Furnished with pipe spacer to support maximum load rating

Size Range — Size 1/2" thru 36" pipe.Material — Carbon SteelFunction — Recommended for the suspension of non-insulated pipe or insulated pipe with Fig. 220 shield.Note — When an oversized clevis is used, a pipe spacer should be placed over the cross bolt to assure that the lower U-strap will not move in on the bolt. When attaching seismic bracing to clevis hangers, a Fig. 1 CBS (cross bolt spacer) must be installed. See TOLCO® Seismic Restraint Approval Guidelines.Approvals — Underwriters’ Laboratories Listed in the USA (UL), Canada (cUL) 3/4" thru 8". Conforms to Federal Specification WW-H-171E, Type 1, and Manufacturers Standardization Society SP-69, Type 1. Also available to accommodate rod schedule per National Fire Protection Association (NFPA) Pamphlet 13. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additonal load, spacing and placement information relating to OSHPD proj-ects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Maximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel.

Component of State of California OSHPD Approved Seismic Restraints System


www.tolco.com15


Fig. 1CBS - Clevis Bolt Spacer

Size Range — Size 1" thru 20" clevis hangerMaterial — Carbon SteelFunction — Used as a spacer at a seismic brace location to keep clevis hanger from collapsing during seismic event.Approvals — Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Installation Note — Fig. 1CBS fits easily over the cross bolt and attaches by pinching tabs down.Finish — Mil GalvanizedNote — Available in Stainless Steel material.



www.tolco.com16


Fig. 1C.I. - A.W.W.A. Clevis Hanger


Pipe Rod Max. Rec. Approx.

Size Size A Pipe O.D. B C D Load Lbs. Wt./100

4 5/8 4.80 8 43⁄4 15⁄8 1430 213 6 3/4 6.90 103⁄16 53⁄4 13⁄4 1940 430 8 3/4 9.05 125⁄8 7 13⁄4 2000 664

10 7/8 11.10 157⁄16 85⁄8 21⁄4 3600 940 *12 7/8 13.20 167⁄8 9 21⁄4 3800 1217 *14 1 15.30 207⁄8 113⁄4 21⁄2 4200 1533

*16 1 17.40 2311⁄16 131⁄2 33⁄8 4600 1925 *18 1 19.50 261⁄16 147⁄8 33⁄8 4800 2223 *20 11⁄4 21.60 291⁄16 163⁄8 33⁄4 4800 4182 *24 11⁄4 25.80 333⁄8 185⁄8 4 4800 5460

*Furnished with pipe spacer to support maximum load rating

Size Range — Size 4" thru 24" pipe.Material — Carbon SteelFunction — For the suspension of flanged or bell and spigot A.W.W.A. cast iron or ductile iron pipe. The O.D. of the A.W.W.A. iron pipe is shown in the data table.Approvals — Conforms to Federal Specification WW-H-171E, Type 1 and Manufacturers Standardization Society SP-69, Type 1.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel.Order By — Figure number, pipe size and finish


www.tolco.com17


Fig. 1A - Clevis Hanger for Insulated Lines


Pipe Rod Size Max Insulation Max. Rec. Approx.

Size A B C D Thickness E Load Lbs. Wt./100

3/4 3/8 41⁄4 33⁄8 1/2 2 610 54 1 3/8 411⁄16 33⁄4 5/8 2 610 59 11⁄4 3/8 51⁄4 41⁄8 7/8 2 610 62

11⁄2 3/8 53⁄4 49⁄16 11⁄16 2 610 67 2 3/8 811⁄16 7 15⁄8 4 610 84 21⁄2 1/2 915⁄16 8 2 4 1130 185

3 1/2 10 5⁄16 81⁄16 13⁄4 4 1130 205 4 5/8 115⁄8 811⁄16 115⁄16 4 1430 252 5 5/8 125⁄8 91⁄4 13⁄4 4 1430 309

6 3/4 14 97⁄8 17⁄8 4 1940 400 8 7/8 163⁄4 11 2 4 2000 607 10 7i/8 193⁄16 121⁄4 21⁄8 4 3600 1032 12 7/8 219⁄16 135⁄8 27⁄16 4 3800 1315

Size Range — Size 3/4" thru 12" pipe.Material — Carbon SteelFunction — Recommended for the suspension of insu-lated pipe where the temperature does not require the use of slides, guides or rollers for movement.Approvals — Conforms to Federal Specification WW-H-171E, Type 1 and Manufacturers Standardization Society SP-69, Type1.Maximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel.Order By — Figure number, pipe size and finish


www.tolco.com18


Fig. 1F — Felt Lined Standard Clevis Hanger

Fig. 1PVC — PVC Coated Standard Clevis Hanger

Size Range — Size 1/2" thru 8" pipe.Material — Carbon SteelInsulation Material — 3/16" feltFunction — The Fig. 1F is designed for the suspension of copper tube so as to prevent electrolysis between tube and hanger. The Fig. 1PVC is designed for steel or other pipe types of same O.D. Both Fig. 1F and Fig. 1PVC act to reduce noise and vibration in pipe or tube system.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL).Maximum Temperature — 650°FFinish — PlainNote — When Fig. 1F is used for steel or other pipe types, consult factory for proper size hanger. Available in Electro-Galvanized and HDG finish or Stainless Steel.Order By — Figure number, nominal tube size and finish


Pipe Rod Size A Max. Rec. Approx.

Size STD NFPA B C D Load Lbs. Wt./100

1/2 3/8 3/8 27/8 1 1 610 36 3/4 3/8 3/8 31/16 111/16 1 610 38 1 3/8 3/8 33/8 17/8 1 610 43

11⁄4 3/8 3/8 33/4 21/16 1 610 47 11⁄2 3/8 3/8 41/16 23/16 1 610 50 2 3/8 3/8 41⁄2 29/16 1 610 56

21⁄2 1/2 3/8 51⁄2 31/16 1 1130 125 3 1/2 3/8 61/8 35/16 11⁄4 1130 141 31⁄2 1/2 3/8 63/4 39/16 11⁄4 1130 153

4 5/8 3/8 75/8 41/16 11⁄2 1430 191 5 5/8 1/2 87/8 51/16 11⁄2 1430 236 6 3/4 1/2 10 55/16 11⁄2 1940 318 8 3/4 1/2 123/4 615/16 2 2000 429

Fig. 1F

Fig. 1PVC


www.tolco.com19

www.tolco.com

Fig. 1U - "Ultra" Clevis Hanger

Dimensions • Weights Pipe Rod Size Max. Rec. Approx.

Size A B C Load Lbs. Wt./100

1/2 thru 1 3/8 31⁄16 19⁄16 200 8 11⁄4 thru 2 3/8 41⁄2 27⁄8 250 18 21⁄2 1/2 53⁄8 215⁄16 350 36 3 1/2 6 3⁄16 39⁄16 350 44 31⁄2 1/2 71⁄4 41⁄16 350 50 4 1/2 75⁄8 49⁄16 400 55

Size Range — Size 1/2" thru 4" pipe.Material — Carbon Steel, Mil. Galvanized to G90.Function — Recommended for the suspension of piping systems.Features — • Fast, easy, snap open and closed installation • Strong lightweight design • Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion • Clevis bottom locks in place to prevent swingingApprovals — Conforms to Manufacturers Standardization Society SP-58, Type1.Maximum Temperature — 650°FFinish — Mil. GalvanizedOrder By — Figure number and pipe size

PATENT PENDING

B

A

C

B

C

A

Load Comparison Chart

Max. Water Water Sch. 40 Total Sch. 80 Total Fig. 1U

Pipe Spacing Sch. 40 Sch. 80 Wt./Ft. Wt./Ft Supported Supported Load Rating

Size per MSS Wt./Ft. Wt./Ft. Sch. 40 Sch. 80 Load Load w/Safety Factor 3.5

1/2 7 0.85 1.09 0.13 0.10 6.87 8.32 2003/4 7 1.13 1.47 0.23 0.19 9.52 11.61 2001 7 1.68 2.17 0.37 0.31 14.36 17.37 2001-1/4 7 2.27 3.00 0.65 0.56 20.43 24.86 2501-1/2 9 2.72 3.63 0.88 0.77 32.39 39.56 2502 10 3.65 5.02 1.45 1.28 51.04 63.01 2502-1/2 11 5.79 7.66 2.07 1.83 86.48 104.43 3503 12 7.57 10.25 3.20 2.86 129.24 157.32 3503-1/2 13 9.11 12.51 4.28 3.85 174.07 212.68 3504 14 10.79 14.98 5.51 4.98 228.20 279.44 400

Revision 12/3/2008


www.tolco.com20


Fig. 1V - "V" Bottom Clevis Hanger

Size Range — Size 1/2" thru 4" pipe.Material — Carbon SteelFunction — Recommended for the suspension of flexible plastic pipe. Use with Fig. 1VT "V" support trough for plastic pipe.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel.Order By — Figure number, size number and finish

Fig. 1VT - "V" Support Trough

Size Range — Size 1/2" thru 4" pipe.Material — Carbon SteelFunction — Designed for use with Fig. 1V as a support for plastic or other flexible pipe systems.Finish — Pre-GalvanizedNote — Available in Stainless Steel material.Order By — Figure number and size number



Size No. Size Size A B C D Load Lbs. Wt./100

1 1/2 3/8 51⁄2 43/4 15/8 150 38 1 3/4 3/8 51⁄2 49/16 15/8 150 38 1 1 3/8 51⁄2 43/8 15/8 150 38 1 11⁄4 3/8 51⁄2 41/8 15/8 150 38 1 11⁄2 3/8 51⁄2 4 15/8 150 38 1 2 3/8 51⁄2 311/16 15/8 150 38 2 21⁄2 1/2 83/4 65/8 13/4 150 115 2 3 1/2 83/4 63/16 13/4 150 115 2 31⁄2 1/2 83/4 513/16 13/4 150 115 2 4 1/2 83/4 57/16 13/4 150 115


For Rod Max. Rec. Approx.

Size No. Pipe Size Length Load Lbs. Wt./100

1* 1/2 - 2 10 ft. 150 540 2** 21⁄2 - 4 10 ft. 150 1080

* Size No. 1 dimensions are 1.5 x 1.5 x 18ga x 10'

** Size No. 2 dimensions are 3 x 3 x 18ga x 10'


www.tolco.com21


Fig. 2 — Adjustable Band Hanger

Pipe Max. Rec. Approx.

Size Rod Size A B C Load Lbs. Wt./100

21⁄2 1/2* 53/4 41⁄4 15/8 600 41 3 1/2* 6 41/8 11⁄4 600 45 31⁄2 1/2* 73/8 51⁄4 21/8 600 52 4 5/8* 73/8 5 15/8 1000 59 5 5/8** 9 61/8 21⁄4 1250 97 6 3/4** 93/8 61⁄2 17/8 1250 139


Size Range — Size 21/2" thru 6" pipe.Material — Carbon Steel, Pre-GalvanizedFunction — Recommended for the suspension of non-insulated pipe or insulated pipe with Fig. 220 shield. Fig. 2NFPA accommodates the reduced rod schedule of the National Fire Protection Association Pamphlet 13.Approvals — Factory Mutual Engineering approved. Underwriters Laboratories Listed. Conforms to Federal Specification WW-H-171E, Type 10 and Manufacturers Standardization Society SP-69, Type 10.Finish — Pre-GalvanizedNote — Available in Stainless Steel material.Order By — Figure number, pipe size and material


www.tolco.com22


Fig. 2F - Adjustable Band Hanger with Felt Lining

Size Range — 1/2" thru 6" copper tubingMaterial — Carbon Steel, Pre-GalvanizedFunction — Recommended for the suspension of copper tube so as to prevent electrolysis. The felt lining also acts to reduce noise in copper or other pipe types. Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL). Conforms to Federal Specification WW-H-171E, Type 10 and Manufacturers Standardization Society SP-69, Type 10.Finish — Pre-GalvanizedNote — When used for steel or other pipe types, consult factory for proper size. Available in Stainless Steel material.Order By — Figure number and copper tube size


Copper Tube Max. Rec. Approx.

Size Rod Size A B C Load Lbs. Wt./100

1/2 3/8 31/8 25/8 13/8 400 12 3/4 3/8 31/8 21⁄2 11/8 400 12 1 3/8 33/8 25/8 11/8 400 13

11⁄4 3/8 33/4 27/8 11⁄4 400 14 11⁄2 3/8 37/8 27/8 11/8 400 15 2 3/8 41⁄4 3 1 400 16

21⁄2* 1/2 53/4 41/8 13/4 600 41 3* 1/2 6 4 11⁄2 600 46 31⁄2* 1/2 73/8 51⁄4 13/8 600 53

4* 5/8 73/8 5 17/8 1000 60 5** 5/8 9 61/8 21⁄2 1250 98 6** 3/4 93/8 61⁄2 21⁄4 1250 140

* 3/8" nut is used when requested. ** 1/2" nut is used when requested.


www.tolco.com23



Pipe Rod Size Max. Rec. Approx.

Size A B C D Load Lbs. Wt./100

1/2 3/8 25/8 21/8 11⁄4 400 14 3/4 3/8 25/8 2 1 400 14 1 3/8 27/8 21/8 1 400 16

11⁄4 3/8 33/8 21⁄2 11⁄4 400 17 11⁄2 3/8 31⁄2 21⁄2 1 400 18 2 3/8 33/4 21⁄2 7/8 400 20

21⁄2 1/2* 5 31⁄2 11⁄2 600 27 3 1/2* 51⁄2 35/8 11⁄4 600 40 31⁄2 1/2* 63/4 45/8 2 600 48

4 5/8* 63/4 43/8 11⁄2 1000 53 5 5/8** 81⁄2 55/8 21/8 1250 91 6 3/4** 91⁄4 57/8 15/8 1250 99 8 3/4** 121⁄4 77/8 25/8 1250 120

* 3/8" nut is used when NFPA rod sizing is requested. ** 1/2" nut is used when NFPA rod sizing is requested.

Fig. 2WON - Adjustable Band Hanger w/o Swivel Nut

Fig. 2FWON - Felt Lined Band Hanger w/o Swivel Nut

Fig. 2WON

Fig. 2F WON


Size Range — (Fig. 2WON) Size 2" thru 8" pipe.(Fig. 2F WON) 1/2" thru 8" copper tubeMaterial — Pre-Galvanized SteelFunction — Recommended for the suspension of non-insulated pipe or insulated pipe with Fig. 220 shield.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL). Conforms to Federal Specification WW-H-171E, Type 7, and Manufacturers Standardization Society SP-69, Type 7, 3/4" thru 6". Figure 2WON is included in our Seismic Restraints catalog approved by the state of California.Finish — Pre-GalvanizedNote — Available in Stainless Steel material.Order By — Figure number and pipe size


www.tolco.com24


Fig. 3 - J-Hanger for Pipe or Conduit

Fig. 3F - Felt Lined J-Hanger for Copper Tubing

Fig. 3PVC - PVC Coated J-Hanger for Pipe or Conduit


Copper Tube Rod Size Max. Rec. Approx.

Size A B C D E F Load Lbs. Wt./100

1/2 3/8 25⁄8 13⁄4 7/16 11⁄2 115⁄16 400 18 3/4 3/8 27⁄8 17⁄8 7/16 111⁄16 21⁄8 400 21 1 3/8 215⁄16 115⁄16 7/16 113⁄16 25⁄16 400 22

11⁄4 3/8 31⁄4 2 7/16 21⁄16 25⁄8 400 25 11⁄2 3/8 39⁄16 23⁄16 7/16 27⁄16 27⁄8 400 27 2 3/8 311⁄16 21⁄8 7/16 29⁄16 31⁄16 400 29

21⁄2 1/2 47⁄16 27⁄16 9/16 33⁄16 35⁄8 500 64 3 1/2 413⁄16 29⁄16 9/16 31⁄2 41⁄16 500 72 31⁄2 1/2 51⁄8 25⁄8 9/16 33⁄4 43⁄8 500 84

4 5/8 61⁄8 33⁄16 9/16 45⁄8 53⁄16 550 138 5 5/8 63⁄4 31⁄4 9/16 51⁄16 53⁄4 550 162 6 3/4 73⁄4 39⁄16 9/16 513⁄16 65⁄8 600 249

8 7/8 93⁄16 315⁄16 9/16 615⁄16 8 760 291 10 7/8 103⁄4 37⁄8 9/16 75⁄8 91⁄8 760 315

Fig. 3

Fig. 3F Fig. 3PVC


Size Range — 1/2" thru 10" pipe sizeMaterial — Carbon SteelFunction — Recommended for the suspension of non-insulated pipe, or insulated pipe with Fig. 220 shield. Side hole allows for wall mounting. Fig. 3F and Fig. 3PVC are designed to reduce noise and vibration and/or prevent electrolysis between pipe and hanger.Approvals — Conforms to Manufacturers Standardization Society SP-69, Type 5. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relat-ing to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Finish — Electro-GalvanizedNote — Available in HDG finish or Stainless Steel materials.Order By — Figure number, pipe size and finish


www.tolco.com25

www.tolco.com

Size Range — (Fig. 4) Size 1/2" thru 30" pipe.Size Range — (Fig. 4F) Size 1/2" thru 21⁄2" copper tubingMaterial — Carbon SteelFunction — Recommended for the suspension of non-insulated pipe or insulated pipe with Fig. 220 shields. (Use Fig. 330 Weldless Eye Nut, Fig. 102 Eye Rod or Fig. 101 Welded Eye Rod.) Also recommended for attachment of sway bracing up to 31/2" pipe size, for larger pipe sizes use Fig. 4A. Fig. 4F and Fig. 4PVC are designed to reduce noise and vibration and/or prevent electrolysis.Approvals — Underwriters’ Laboratories Listed in the USA (UL), Canada (cUL) 1/2" - 8", and approved by Factory Mutual Engineering, 3/4" - 8". Federal Specification WW-H-171E, Type 4, 11⁄2" thru 24" and Manufacturers Standardization Society SP-69, Type 4. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spac-ing and placement information relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Note — When the Fig. 4 is used as a sway brace, to ensure performance, the UL Listing requires that it must be used with other TOLCO®

brace products.Maximum Temperature — 750°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, pipe size and finish.Order Note — When ordering Fig. 4F allow for 3/16" felt on each half of clamp.

Revision 3/7/2007

Fig. 4FFig. 4PVC

Dimensions • Weights Max. Design Load Lbs. Pipe For Service Temp. Approx. Size A B C D Bolt Size 650° 750°F Wt./100

1/2 37⁄16 1/4 11⁄8 11⁄8 5/16 500 445 29 3/4 39⁄16 1/4 11⁄4 11⁄4 5/16 500 445 31 1 39⁄16 1/4 11⁄4 15⁄16 5/16 500 445 35

11⁄4 43⁄16 3/8 13⁄8 111⁄16 5/16 500 445 40 11⁄2 49⁄16 3/8 15⁄8 17⁄8 5/16 800 715 42 2* 59⁄16 3/8 2 21⁄4 3/8 1040 930 93

21⁄2* 67⁄16 3/8 21⁄2 23⁄4 1/2 1040 930 126 3* 7 3/8 23⁄4 31⁄16 1/2 1040 930 141 31⁄2* 711⁄16 3/8 31⁄8 33⁄8 1/2 1040 930 154

4 81⁄2 5/8 35⁄16 311⁄16 1/2 1040 930 229 5 93⁄4 3/4 37⁄8 43⁄8 5/8 1040 930 261 6 115⁄8 3/4 47⁄8 51⁄8 3/4 1615 1440 537

8 135⁄16 1 55⁄8 6 3/4 1615 1440 625 10 161⁄2 1 71⁄4 71⁄4 7/8 2490 2220 1378 12 181⁄2 1 81⁄4 81⁄4 7/8 2490 2220 1574

14 20 11⁄8 9 9 7/8 2490 2220 2103 16 23 11⁄8 101⁄4 101⁄4 7/8 2490 2220 2314 18 257⁄8 11⁄4 111⁄2 111⁄2 1 3060 2730 3276

20 28 13⁄8 121⁄2 121⁄2 11⁄8 3060 2730 3863 24 331⁄2 15⁄8 151⁄4 151⁄4 11⁄4 3060 2730 5222 30 417⁄8 2 19 19 13⁄4 3500 3360 10511

*Meets UL 203A requirements for attachment of sway bracing. Horizontal design load for 1/2"-2" - 380#, 21⁄2" - 395#, 3" - 435#, 31⁄2" - 540#

Fig. 4

Fig. 4 - Standard Pipe Clamp

Fig. 4F - Standard Pipe Clamp Felt Lined

Fig. 4PVC - Standard Pipe Clamp PVC Coated



www.tolco.com26


Fig. 4A - Pipe Clamp for Sway Bracing

Size Range — 4" thru 8" pipe. For sizes smaller than 4" use TOLCO® Fig. 4.Material — Carbon SteelFunction — For bracing pipe against sway and seismic disturbance.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada

(cUL) 4" thru 8". Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). Installation Instructions — The Fig. 4A is the "braced pipe" attachment component of a longitudinal, lateral or riser brace assembly. It is intended to be combined with the "bracing pipe" and TOLCO transitional and structural attachment component(s) to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed.To Install — Place the Fig. 4A over the pipe to be braced. Attach TOLCO transitional fitting, either Fig. 980, 910 or 909, to the clamp ears. Tighten bolts and nuts; torque requirement is a minimum of 50 ft. lbs. Transitional fit-ting attachment can pivot for adjustment to proper brace angle.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, pipe size and finish

TOLCO® brand bracing components are desgined to be compatible ONLY with other TOLCO® brand bracing components, resulting in a Listed seismic bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO® brand bracing components, in the instance that such TOLCO® brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under the TOLCO® brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect, incidental or consequential damages of any kind, including but not limited to loss of business or profit, where non-TOLCO brand bracing components have been, or are used.


Pipe Max. Horizontal Approx.

Sizes A B C D Bolt Size Design Load Wt./100

4 81⁄2 9/16 33⁄8 311⁄16 1/2 2015 221 5 93⁄4 9/16 37⁄8 43⁄8 1/2 2015 253 6 111⁄2 5/8 5 51⁄8 1/2 2015 513 8 131⁄4 3/4 611⁄16 61⁄8 1/2 2015 601


Fig. 4A - Longitudinal Brace Fig. 4A - Lateral Brace(UL Listed Up to 4" IPS)


www.tolco.com27


Size Range — 3/4" thru 8" pipe.Material — Carbon SteelFunction — For bracing pipe against sway and seismic disturbance.Features — This product's design incorporates concentric loading of the "brace pipe", connection components and fasteners which is critical to the performance of seismic bracing assemblies.Approvals — Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). Included in our Seismic Restrains Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, pipe size and finish.Installation Instructions — The Fig. 4B is the "braced pipe" attachment component of a longitudinal or lateral sway brace assembly. It is intended to be combined with the "bracing pipe" and TOLCO transitional and structural attachment component(s) to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed.To Install — Place the Fig. 4B over the pipe to be braced. Attach other TOLCO transitional fitting, Fig. 909, 910 or 980. Tighten bolts and nuts. Transitional fitting attachment can pivot for adjustment to proper brace angle.

TOLCO® brand bracing components are desgined to be compatible ONLY with other TOLCO® brand bracing components, resulting in a Listed seismic bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO® brand bracing components, in the instance that such TOLCO® brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under the TOLCO® brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect, incidental or consequential damages of any kind, including but not limited to loss of business or profit, where non-TOLCO brand bracing components have been, or are used.

Fig. 4B - Pipe Clamp for Sway Bracing Component of State of California OSHPD Approved Seismic Restraints System


Pipe Rod Size Max. Design Approx.

Sizes A B C D Bolt Size Load Lbs. Wt./100

3/4 3/8 1 27⁄8 25⁄8 5/16 330 56 1 3/8 1 31⁄4 215⁄16 5/16 330 60 11⁄4 3/8 1 39⁄16 31⁄4 5/16 330 74

11⁄2 3/8 1 313⁄16 37⁄16 5/16 330 79 2 3/8 11⁄2 51⁄8 45⁄8 5/16 440 156 21⁄2 1/2 13⁄4 55⁄8 53⁄8 3/8 440 176

3 1/2 17⁄8 63⁄4 61⁄8 3/8 660 198 31⁄2 1/2 2 71⁄4 63⁄4 3/8 660 219 4 5/8 2 85⁄8 71⁄4 1/2 800 288

5 5/8 2 97⁄8 85⁄16 5/8 980 390 6 3/4 21⁄8 1015⁄16 91⁄2 5/8 980 448 8 7/8 21⁄8 137⁄16 111⁄2 3/4 1200 691

Fig. 4B - Hanger/Longitudinal Brace

Shown with two TOLCO® Fig. 980’s and Schedule 40 brace pipe.


www.tolco.com28


Fig. 4H - Heavy Duty Pipe ClampSize Range — 3" thru 24" pipeMaterial — Carbon SteelFunction — Recommended for the suspension of heavy-duty pipe lines. (Use with Fig. 330 Weldless Eye Nut, Fig. 102 Eye Rod or Fig. 101 Welded Eye Rod).Approvals — Conforms to Federal Specification WW-H-171E, Type 4, and Manufacturers Standardization Society SP-69, Type 4.Maximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.

Fig. 4CI - A.W.W.A. Pipe ClampSize Range — 4" thru 24" pipeMaterial — Carbon SteelFunction — Recommended for the suspension of flanged or bell and spigot A.W.W.A. cast iron or ductile iron pipe. The O.D. of the A.W.W.A. iron pipe is shown in the data table. Used with Fig. 330 Weldless Eye Nut, Fig. 102 Eye Rod or Fig. 101 Welded Eye Rod.Approvals — Conforms to Federal Specification WW-H-171E, Type 4, and Manufacturers Standardization Society SP-69, Type 4.Maximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, pipe size and finish

Dimensions • Weights Pipe Bolt Max. Rec. Approx.

Sizes Pipe O.D. A B Size Load Lbs. Wt./100

4 4.80 11⁄8 41⁄16 5/8 1400 860 6 6.90 11⁄8 51⁄16 5/8 1400 1060 8 9.05 11⁄8 63⁄16 5/8 1400 1230 10 11.10 11⁄8 71⁄4 5/8 1400 1430 12 13.20 11⁄8 85⁄16 5/8 1400 1630 14 15.30 13⁄4 97⁄8 3/4 2000 2300

16 17.40 13⁄4 115⁄16 7/8 2500 3725 18 19.50 17⁄8 129⁄16 1 3000 4200 20 21.60 2 135⁄8 1 3100 4575 24 25.80 2 165⁄16 11⁄4 4500 6400

Dimensions • Weights Pipe Max. Rec.Load Lbs. — Temps. Approx.

Sizes A B C Bolt Size 650F 750°F Wt./100

3 1 3 41⁄8 3/4 3370 3005 498 4 1 311⁄16 415⁄16 7/8 3515 3135 634 5 1 45⁄16 59⁄16 7/8 3515 3135 714 6 11⁄8 53⁄16 611⁄16 1 4865 4340 1351 8 11⁄8 61⁄4 73⁄4 1 4865 4340 1573 10 11⁄4 77⁄8 91⁄2 11⁄4 6010 5360 2537 12 15⁄8 91⁄2 115⁄8 11⁄2 8675 7740 4300 14 15⁄8 101⁄8 121⁄4 11⁄2 9120 8135 5228 16 15⁄8 113⁄16 135⁄16 11⁄2 9120 8135 5657 18 15⁄8 123⁄16 145⁄16 11⁄2 9150 8160 6914 20 15⁄8 135⁄16 157⁄16 11⁄2 9150 8160 7468 24 13⁄4 153⁄8 173⁄4 11⁄2 9200 `8205 12629

* Consult factory for sizes larger than 24" Based on the allowable stresses shown in the ANSI code for pressure piping.


www.tolco.com29


Size Range — 2¹⁄₂" through 8" IPS.

Material — Carbon Steel

Function — For bracing pipe against sway and seismic disturbance.

Approvals — Underwriter's Laboratories Listed in the USA (UL) and Canada (cUL) 2¹⁄₂" - 8". Approved by Factory Mutual Engineering (FM),2¹⁄₂" - 8" pipe.

Installation Instructions — The Fig. 4L is the "braced pipe" attachment component of a longitudinal sway brace assembly. It is intended to be combined with the "bracing pipe" and TOLCO structural attachment component to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed.

To Install — Place the Fig. 4L over the pipe to be braced and tighten bolts. Then engage "bracing pipe" into jaw opening and tighten set bolt until hex head snaps off. Jaw attachment can pivot for adjustment to proper brace angle.

Finish — Plain

Note — Available in Electro-Galvanized and HDG finish.

Order By — Figure number, pipe size and finish.

TOLCO® brand bracing components are designed to be compatible ONLY with other TOLCO® brand bracing components, resulting in a Listed seismic bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO® brand bracing components, in the instance that such TOLCO® brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under the TOLCO® brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect, incidental or consequential damages of any kind, including but not limited to loss of business or profit, where non-TOLCO brand bracing components have been, or are used.

Fig. 4L

Longitudinal “In-Line” Sway Brace Attachment

4-Way Riser Brace(Plan view)

* Load shown is allowable with brace installed, between 30° - 90°. FM approved when used with 1", 11⁄4", 11⁄2" or 2" Sch. 40 brace pipe.


Bolt Max. Rec. *Max Design Approx.

Sizes A C D Size

Load Lbs. Load Lbs. Wt./100 (cULus) (FM)

21⁄2 67⁄16 21⁄2 23⁄4 1/2 2015 3000 253 3 7 23⁄4 31⁄16 1/2 2015 1550 268 4 81⁄2 33⁄8 311⁄16 1/2 2015 1550 348 5 93⁄4 37⁄8 43⁄8 1/2 2015 1450 380 6 111⁄2 5 51⁄8 1/2 2015 1450 640 8 131⁄4 55⁄8 55⁄8 1/2 2015 1450 728

Longitudinal Brace


www.tolco.com30


Size Range — 1/2" thru 36" pipe.Material — Carbon SteelFunction — Recommended for the suspension of pipe requiring up to 4" of insula-tion and where flexibility of the clamp may be necessary. Use Fig. 330 Weldless Eye Nut, Fig. 102 Eye Rod or Fig. 101 Welded Eye Rod. Also rec-ommended for the attachment of sway bracing up to 8 inches. Refer to TOLCO® State of California Approved Seismic Restraint Product Manual.Approvals — Conforms to Federal Specification WW-H-171E, Type 3 and Manufacturers Standardization Society SP-69, Type 3. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Maximum Temperature — 750°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, pipe size and finish.


Max. Design Load Lbs. Pipe For Service Temp. Approx. Size A B C D E Bolt Size 650° 750°F Wt./100

1/2 3/8 213⁄16 213⁄16 11⁄2 7/8 3/8 950 — 73 3/4 5/8 3 23⁄8 111⁄16 11⁄16 3/8 950 — 73 1 5/8 31⁄4 25⁄8 115⁄16 15⁄16 3/8 950 — 77

11⁄4 5/8 31⁄2 27⁄8 23⁄16 19⁄16 3/8 950 — 79 11⁄2 1 53⁄8 41⁄2 25⁄8 13⁄4 5/8 1545 1380 236 2 1 513⁄16 415⁄16 215⁄16 21⁄16 5/8 1545 1380 251

21⁄2 1 61⁄8 51⁄4 31⁄4 23⁄8 5/8 1545 1380 274 3 1 63⁄4 57⁄8 35⁄8 211⁄16 5/8 1545 1380 289 31⁄2 1 73⁄16 65⁄16 37⁄8 3 5/8 1545 1380 315

4 1 73⁄4 65⁄8 411⁄16 39⁄16 3/4 2500 2230 745 5 1 89⁄16 77⁄16 55⁄16 43⁄16 3/4 2500 2230 828 6 11⁄2 97⁄8 81⁄2 61⁄8 43⁄4 7/8 2865 2555 1261

8 11⁄2 11 95⁄8 75⁄16 515⁄16 7/8 2865 2555 1535 10 11⁄2 12 101⁄2 87⁄8 75⁄16 1 3240 2890 2173 12 11⁄2 131⁄8 115⁄8 915⁄16 87⁄16 1 3240 2890 2404

14 2 145⁄16 129⁄16 115⁄16 99⁄16 11⁄4 4300 3835 4002 16 2 159⁄16 1313⁄16 125⁄16 109⁄16 11⁄4 4300 3835 4362 18 2 167⁄8 151⁄8 133⁄8 115⁄8 11⁄4 4300 3835 4935

20 2 181⁄4 163⁄8 151⁄8 131⁄4 13⁄8 5490 4900 6570 24 2 207⁄16 187⁄16 175⁄16 155⁄16 13⁄8 4500 4015 7524 30 21⁄2 26 23 22 19 13⁄8 7500 — 19502 36 21⁄2 323⁄8 287⁄8 255⁄8 221⁄8 13⁄4 10500 — 23488

Based on allowable stresses shown in the ANSI code for pressure piping.

Fig. 5 - Standard Double Bolt Pipe ClampComponent of State of California

OSHPD Approved Seismic Restraints System


www.tolco.com31


Size Range — 6" thru 36" pipe.Material — Carbon SteelFunction — Recommended for the suspension of heavy duty high temperature pipe runs requiring up to 4" of insulation and where flexibility of the clamp may be necessary. Use with Fig. 330 Weldless Eye Nut, Fig. 102 Eye Rod or Fig. 101 Welded Eye Rod.Approvals — Conforms to Federal Specification WW-H-171E, Type 3 and Manufacturers Standardization Society SP-69, Type 3.Maximum Temperature — 750°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, pipe size and finish.


Max. Design Load Lbs. Pipe For Service Temp. Approx. Size A B C D E Bolt Size 650° 750°F Wt./100

6 13⁄4 103⁄16 815⁄16 6 43⁄4 1 3500 3125 1200 8 2 113⁄8 101⁄8 71⁄4 6 11⁄8 4800 4285 1850 10 21⁄4 131⁄8 113⁄8 9 71⁄4 11⁄4 5500 4910 3030

12 21⁄2 145⁄16 129⁄16 103⁄8 85⁄8 13⁄8 7000 6250 4200 14 21⁄2 151⁄2 131⁄2 115⁄8 95⁄8 11⁄2 9500 8485 6000 16 3 171⁄8 147⁄8 131⁄8 107⁄8 13⁄4 10000 8930 8000

18 31⁄2 181⁄4 161⁄4 141⁄2 121⁄2 2 13800 12325 11500 20 31⁄2 193⁄4 171⁄4 16 131⁄2 2 15300 13665 14000 24 31⁄2 223⁄8 195⁄16 181⁄2 151⁄2 2 16300 14555 19000

30 41⁄4 323⁄4 281⁄4 243⁄8 197⁄8 21⁄4 20500 — 40600 36 41⁄2 401⁄4 343⁄4 301⁄8 225⁄8 23⁄4 28000 — 67800

Based on allowable stresses shown in the ANSI code for pressure piping.

Fig. 5H - Heavy Duty Double Bolt Pipe Clamp


www.tolco.com32


Size Range — (Fig. 6) 1/2" thru 20" pipe (Fig. 6F) 1/2" thru 21⁄2" copper tubing (Fig. 6PVC) 1/2" thru 6" pipeMaterial — Carbon SteelInsulation Material — (Fig. 6F) 3/16" felt.Function — Used for supporting vertical piping.Approvals — Underwriters’ Laboratories Listed in the USA (UL), Canada (cUL) 1/2" - 8". Factory Mutual Engineering Approved, 3/4" thru 8". Conforms to Federal Specification WW-H-171E, Type 8, 3/4" thru 20" and Manufacturers Standardization Society SP-69, Type 8.Maximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — (Fig. 6 and Fig. 6PVC) pipe size and finish. (Fig. 6F) copper tube size and finish. (Fig. 6F is available for Iron Pipe Size, consult factory.

Fig. 6FFig. 6PVC

Fig. 6

Fig. 6 - Riser Clamp

Fig. 6F - Felt Lined Riser Clamp

Fig. 6PVC - PVC Coated Riser Clamp


Pipe Max. Rec. Approx.

Size A B C Bolt Size Load Lbs. Wt./100

1/2 91⁄4 1/2 11⁄8 3/8 255 144 3/4 91⁄4 1/2 11⁄8 3/8 255 144 1 99⁄16 1/2 11⁄4 3/8 255 147

11⁄4 911⁄16 1/2 13⁄8 3/8 255 150 11⁄2 103⁄8 1/2 11⁄2 3/8 255 153 2 103⁄4 1/2 2 3/8 255 165

21⁄2 11 5/8 21⁄4 3/8 390 228 3 12 5/8 3 3/8 530 246 31⁄2 13 5/8 31⁄4 1/2 670 264

4 131⁄2 3/4 33⁄8 1/2 810 347 5 141⁄2 3/4 43⁄8 1/2 1160 385 6 151⁄8 7/8 47⁄8 1/2 1570 564

8 181⁄2 1 53⁄4 5/8 2500 1017 10 201⁄4 1 71⁄4 5/8 2500 1138

12 223⁄4 1 81⁄4 5/8 2700 1759 14 24 11⁄8 9 5/8 2700 1922 16 26 11⁄8 101⁄4 3/4 2900 3245 18 28 11⁄4 111⁄2 3/4 2900 3372 20 30 13⁄8 121⁄2 3/4 2900 3499


www.tolco.com33


Size Range — 1/2" thru 12" pipeMaterial — Carbon SteelFunction — Recommended for support of pipe lines running at a definite distance from the wall or floor of a building or structure.Maximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Special “B” dimensions available on request, consult factory.Order By — Figure number, pipe size and finish

Fig. 7 - Offset Pipe Clamp

Size Range — 3/4" thru 8" pipeMaterial — Carbon SteelFunction — For suspending or supporting piping runs where the pipe cannot be determined until installation. Field modify to suit conditionsMaximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Special “B” dimensions available on request, consult factory.Order By — Figure number, pipe size and finish

Fig. 8 - Extended Pipe Clamp


Pipe Hole Size Max. Rec. Approx.

Size A B C Bolt Size Load Lbs. Wt./100

1/2 513⁄16 27⁄16 7/16 3/8 190 107 3/4 515⁄16 21⁄2 7/16 3/8 190 109 1 61⁄4 25⁄8 7/16 3/8 190 116 11⁄4 611⁄16 23⁄4 7/16 3/8 190 126 11⁄2 615⁄16 3 7/16 3/8 190 134 2 85⁄16 33⁄16 7/16 3/8 420 191 21⁄2 87⁄8 37⁄16 7/16 3/8 420 209 3 91⁄2 33⁄4 7/16 3/8 420 232 31⁄2 101⁄16 4 7/16 3/8 420 250 4 109⁄16 41⁄4 9/16 1/2 610 370 6 143⁄8 55⁄16 9/16 1/2 870 650 8 167⁄16 65⁄16 9/16 1/2 870 787 10 211⁄2 73⁄8 13/16 3/4 925 1238 12 247⁄8 83⁄8 13/16 3/4 1225 2100


Pipe Bolt Approx.

Size A B Size Wt./100

3/4 47⁄16 12 3/8 225 1 411⁄16 12 3/8 230 11⁄4 5 12 3/8 235 11⁄2 51⁄4 12 3/8 240 2 6 12 1/2 345 21⁄2 71⁄4 12 1/2 360 3 77⁄8 12 1/2 375 31⁄2 83⁄8 12 12 390 4 91⁄4 12 1/2 500 5 101⁄2 12 1/2 545 6 121⁄2 12 5/8 870 8 145⁄8 12 5/8 980


www.tolco.com34


Size Range — 4" thru 24" pipeMaterial — Carbon SteelFunction — Clamp is used for underground A.W.W.A. cast iron and ductile iron water pipe to prevent joints from separating. The O.D. of the A.W.W.A. pipe is shown in the data table.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, pipe size and outside diameter of pipe. Order Fig. 9X lugs, tie rods and hex nuts separately.

Fig. 9 - Underground Socket Clamp

Size Range — 3/4" thru 11⁄2" rodMaterial — Cast IronFunction — Used with Fig. 9 to secure tie rods. The projecting lug bears against the clamp bolt to prevent washer and tie rod from slipping off clamp.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish

Fig. 9X - Socket Clamp Washer


Pipe Pipe Fig. 9X Approx.

Size O.D. A B* Bolt Size Washer Size Wt./100

4 4.80 109⁄16 121⁄2 5/8 3/4 866 6 6.90 13 151⁄8 5/8 3/4 1058 8 9.05 16 177⁄8 5/8 3/4 1246 10 11.10 173⁄4 191⁄8 5/8 3/4 1434 12 13.20 193⁄4 23 5/8 3/4 1614 14 15.30 253⁄4 277⁄8 7/8 11⁄4 4557 16 17.40 293⁄16 317⁄8 1 11⁄4 6730 18 19.50 31 3311⁄16 11⁄4 11⁄4 7643 20 21.60 301⁄8 357⁄8 11⁄4 11⁄2 9174 24 25.80 365⁄8 405⁄8 11⁄2 11⁄2 11991


Tie Rod Approx.

Size A B Wt./100

3/4 23⁄8 7/8 95 1 4 15⁄16 253 11⁄4 4 13⁄8 248 11⁄2 4 15⁄8 240


www.tolco.com35


Size Range — 4" thru 24" pipeMaterial — Carbon SteelFunction — Clamp is used for underground A.W.W.A. cast iron and ductile iron water pipe to prevent joints from separating. The O.D. of the A.W.W.A. pipe is shown in the data table.Approvals — Conforms to National Fire Protection Association (NFPA) Pamphlet 24, 4" thru 12" pipe sizes.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, pipe size and outside diameter of pipe. Order Fig. 14X plate washers, tie rods and hex nuts separately.

Fig. 14 - Double Bolt Underground Socket Clamp

Size Range — 3/4" thru 11⁄2" pipeMaterial — Carbon SteelFunction — Used with Fig. 14 to secure tie rods.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.

Fig. 14X - Plate Washer


Pipe Pipe Fig. 14X Approx.

Size O.D. A B Bolt Size Washer Size Wt./100

4 4.80 141⁄16 95⁄16 5/8 3/4 1275 6 6.90 167⁄16 1111⁄16 5/8 3/4 1455 8 9.05 195⁄8 147⁄8 5/8 3/4 2350 10 11.10 2113⁄16 171⁄16 3/4 3/4 2925 12 13.20 241⁄2 191⁄4 7/8 1 4030 14 15.30 2615⁄16 2111⁄16 7/8 1 5385 16 17.40 303⁄4 243⁄4 1 11⁄8 7645 18 19.50 345⁄16 275⁄16 11⁄4 11⁄4 9425 20 21.60 365⁄8 295⁄8 11⁄4 11⁄2 10975 24 25.80 421⁄8 343⁄8 11⁄2 11⁄2 14865


Tie Rod Hole Size Approx. Size A B C Wt./100

3/4 3 1⁄2 7/8 120 1 31⁄2 1⁄2 11⁄8 157 11⁄8 31⁄2 5⁄8 11⁄4 194 11⁄4 31⁄2 3⁄4 13⁄8 230 11⁄2 31⁄2 3⁄4 15⁄8 240


www.tolco.com36


Data Table for Fig. 20S


Pipe Hole Max. Rec. Approx.

Sizes A B C D Size Load Lbs. Wt./100

1/2 41⁄8 5/16 27⁄8 3/4 7/16 410 21 3/4 45⁄16 7/16 3 15/16 7/16 410 24 1 49⁄16 9/16 33⁄8 11⁄8 7/16 410 26 11⁄4 415⁄16 11/16 33⁄4 11⁄2 7/16 410 30 11⁄2 53⁄16 13/16 41⁄4 15⁄8 7/16 410 33 2 53⁄4 11⁄16 43⁄4 21⁄4 7/16 410 38 21⁄2 61⁄4 19⁄16 51⁄4 23⁄4 7/16 610 102 3 67⁄8 15⁄8 57⁄8 33⁄8 7/16 610 118 31⁄2 73⁄8 17⁄8 63⁄8 37⁄8 7/16 610 130 4 83⁄8 21⁄8 7 43⁄8 9/16 725 159 5 97⁄16 25⁄8 77⁄8 53⁄8 9/16 725 191 6 101⁄2 33⁄16 87⁄8 67⁄16 9/16 725 234 8 14 41⁄4 111⁄2 83⁄8 11/16 900 446

Size Range — 1/2" thru 8" pipeMaterial — Carbon SteelFunction — Recommended for supporting pipe with fittings vertically or horizontally to walls or ceiling. Fig. 20S will support pipe flush with mounting surface.Approvals — Conforms to Federal Specification WW-H-171E, Type 26 and Manufacturers Standardization Society SP-69, Type 26.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, pipe size, material and finish

Size Range — 1/2" thru 2" pipeMaterial — Pre-Galvanized SteelFunction — Light duty strap that attaches pipe or copper tubing to horizontal or vertical structure.Finish — Pre-GalvanizedNote — Available with felt lining, order TOLCO® Fig. 21F. Order By — Figure number and pipe size

Fig. 20 - Standard Pipe Strap

Fig. 20S - Flush Mount Pipe Strap

FIG. 21 - “Tin Strap”

Data Table for Fig. 20


Pipe Hole Max. Rec. Approx.


1/2 37⁄8 3/4 31⁄16 15/32 7/16 410 16 3/4 4 13/16 31⁄8 15⁄16 7/16 410 21 1 49⁄16 7/8 33⁄8 11⁄2 7/16 410 26 11⁄4 415⁄16 1 33⁄4 17⁄8 7/16 410 30 11⁄2 53⁄16 13⁄16 41⁄4 21⁄8 7/16 410 33 2 53⁄4 17⁄16 43⁄4 25⁄8 7/16 410 38 21⁄2 61⁄4 111⁄16 51⁄4 31⁄8 7/16 610 102 3 67⁄8 2 57⁄8 33⁄4 7/16 610 118 31⁄2 73⁄8 21⁄4 63⁄8 41⁄4 7/16 610 130 4 83⁄8 21⁄2 7 43⁄4 9/16 725 159 5 97⁄16 31⁄16 77⁄8 513⁄16 9/16 725 191 6 101⁄2 35⁄8 87⁄8 67⁄8 9/16 725 234 8 14 45⁄8 111⁄2 9 11/16 900 446


www.tolco.com37


Size Range — 3/4" thru 2" CPVC pipeMaterial — Pre-Galvanized SteelFunction — Intended to perform as a hanger to support CPVC piping used in automatic fire sprinkler systems. The product acts as a hanger when tab is upward and the fastener screw is in the horizontal position. Figure 22 can be installed on the top of a beam, but in this situation acts as a guide to the piping which is supported by the beam itself. It is not intended to support CPVC pipe from under a flat horizontal surface, such as a ceiling.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL) to support fire sprinkler piping. May be installed in wood using fasteners supplied with product, or into minimum 20 gauge steel using (1) 1/4" x 1" tek type screw. Meets and exceeds the requirements of NFPA 13, 13R and 13D.Features — Fig. 22 incorporates features which protect the pipe and ease installation. The flared edge design protects CPVC pipe from any rough surface. It is easily attached to the building structure using the special UL Listed hex head self threading screw* furnished with the product. It is recommended that rechargeable electric drills fitted with a hex socket attachment to be used as installation tools. No impact tools (such as a hammer) are allowed. Damage has been known to result from installations using impact type tools. No pre-drilling of a pilot hole in wood is required.Finish — Pre-GalvanizedOrder By — Figure number and CPVC pipe size.

* Hardened hex head self threading screw is furnished with the

product and is the minimum fastener size acceptable.

Fig. 22 - Hanger for CPVC Plastic Pipe

Single Fastener Strap Type


CPVC Max. Hanger Fastener Hex Approx.

Pipe Size A B C Spacing (Ft.) Head Size Wt./100

3/4 27⁄16 15⁄16 13⁄16 51⁄2 5/16 9 1 211⁄16 17⁄16 13⁄16 6 5/16 9 11⁄4 31⁄16 15⁄8 13⁄16 61⁄2 5/16 11

11⁄2 35⁄16 13⁄4 13⁄16 7 5/16 12 2 33⁄4 21⁄8 13⁄16 8 5/16 15


www.tolco.com38


Size Range — 3/4" thru 3" CPVC pipeMaterial — Pre-Galvanized SteelFunction — Intended to perform as a hanger to support CPVC pip-ing used in automatic fire sprinkler systems. Fig. 23 can be installed on the top, bottom or side of a beam.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL) sizes 3/4" thru 2" to support fire sprinkler piping. May be installed in wood using fasteners supplied with product, or into minimum 20 gauge steel using (2) 1/4" x 1" tek type screw. Meets and exceeds the requirements of NFPA 13, 13R and 13D.Features — Fig. 23 incorporates features which protect the pipe and ease installation. The flared edge design protects the CPVC pipe from any rough surface. It also incorporates snap restrainers allowing easier and faster installation. Easily attaches to the building structure using the two UL Listed hex head self threading screws* furnished with the product. It is recommended that rechargeable electric drills fitted with a hex socket attachment be used as instal-lation tools. No impact tools (such as a hammer) are allowed. Damage has been known to result from installations using impact type tools. No pre-drilling of a pilot hole in wood is required.Finish — Pre-GalvanizedOrder By — Figure number and pipe size




Double Fastener Strap Type


CPVC Max. Hanger Fastener Hex Approx.


3/4 31⁄8 19⁄16 13⁄16 51⁄2 5/16 9 1 33⁄8 111⁄16 13⁄16 6 5/16 9 11⁄4 43⁄16 23⁄32 13⁄16 61⁄2 5/16 11 11⁄2 47⁄16 27⁄32 13⁄16 7 5/16 12 2 47⁄8 27⁄16 13⁄16 8 5/16 15 21/2 109/32 211/16 13/16 Consult Factory 5/16 22 3 117/8 3 13/16 Consult Factory 5/16 25


www.tolco.com39

www.tolco.com

Dimensions • Weights CPVC Max. Hanger Fastener Hex Approx.


3/4 25⁄16 15⁄32 13⁄16 51⁄2 5/16 9 1 25⁄8 15⁄16 13⁄16 6 5/16 9 11⁄4 3 11⁄2 13⁄16 61⁄2 5/16 11 11⁄2 31⁄4 15⁄8 13⁄16 7 5/16 12 2 311⁄16 127⁄32 13⁄16 8 5/16 15

Size Range — 3/4" thru 2" CPVC pipeMaterial — Pre-Galvanized SteelFunction — Intended to perform as a hanger to support CPVC piping used in automatic fire sprinkler systems. Can be installed on the top or on the bottom of a beam.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL) to support fire sprinkler piping. May be installed in wood using fasteners supplied with product, or into minimum 20 gauge steel using (2) 1/4" x 1" tek type screws. Meets and exceeds the requirements of NFPA 13, 13R and 13D.Features — Fig. 24 incorporates features which protect the pipe and ease installation. The flared edge design protects the CPVC pipe from any rough surface. Easily attaches to the building structure using the two UL Listed hex head self threading screws* furnished with the product. It is recommended that rechargeable electric drills fitted with a hex socket attachment be used as installation tools. No impact tools (such as a ham-mer) are allowed. Damage has been known to result from installations using impact type tools. No pre-drilling of a pilot hole in wood is required.Finish — Pre-GalvanizedOrder By — Figure number and pipe size




Double Fastener Strap Type - Side Mount

Revision 4/13/2010


www.tolco.com40


Size Range — One size fits 3/4" thru 2" pipe.Material — Pre-Galvanized SteelFunction — Designed to be used in conjunction with TOLCO® Band Hangers to restrict the upward movement of piping as it occurs during sprinkler head activation or earthquake type activity. The surge restrainer is easily and efficient-ly installed by snapping into a locking position on the band hanger. This product is intended to satisfy the requirements as indicated in the National Fire Protection Association NFPA 13, 2010 edition, 9.2.3.4.4.1 and 9.2.3.4.4.4 Can be used to restrain either steel pipe or CPVC plastic Pipe.Approvals — Underwriters’ Laboratories Listed only when used with TOLCO band hangers Fig. 2, 2NFPA and 200, in the USA (UL) and Canada (cUL).Finish — Pre-GalvanizedOrder By — Figure number and TOLCO band hanger, size from 3/4"thru 2".

Patent #5,344,108

Fig. 25 - Surge Restrainer


www.tolco.com41

www.tolco.com

Size Range — Fits screws supplied with all TOLCO CPVC hangers.

Material — Carbon Steel

Finish — Pre-Galvanized (Zinc)

Function — To be used anywhere a screw cannot achieve full embedment due to thickness of wood structural material when installed. Fig. 27B allows full pull out load capacity of screws when installed to the standard screws supplied with all TOLCO CPVC hangers (Fig. 22, 23, 24, 28, 28M & 29).

Fig 27B - Speed Nut

Revision 10/5/2010

HANGER APPLICATION

FIG. 27B(1) REQUIRED

HIGH SIDEOF HANGER

APPLICATIONHANGER AND RESTRAINT


FIG. 27B(1) REQUIREDHIGH SIDEOF HANGER

HANGER APPLICATION


HANGER AND RESTRAINTAPPLICATION


www.tolco.com42


Fig. 28 - "Stand-Off" Hanger & Restrainer for

CPVC Plastic Pipe

Size Range — ¾" through 2"

Material — Carbon Steel, Pre-Galvanized

Function — Designed to be used as a hanger and restrainer for CPVC piping where the "stand-off" design will ease installation by eliminating the need for wood blocking.

Features:

• Flared edge design protects CPVC pipe from any rough or abrasive surfaces.• Unique twist and lock design holds pipe firmly in place and allows retrofit type

of installation.• The "Stand-Off" design eliminates the need for wood block extension.• Can be installed on horizontal or vertical piping regardless of mounting

surface orientation.• Attaches easily to wood structure with two hex head self-threading screws

furnished with product.• Installs easily using rechargeable electrical driver with 5/16" extension socket

eliminating impact tool damage to pipe.• Attaches easily to steel, minimum 18 gauge with (2) 1/4" x 1" tek type self drilling

tapping screws.• UL Listed as a hanger and a restrainer for fire sprinkler piping.

Approvals — Underwriters' Laboratory Listed in the USA (UL) and Canada (cUL) to support automatic fire sprinkler systems. May be installed into wood using fasteners supplied with product, or into minimum 18 gauge steel using (2) 1/4" x 1" tek type screws. Meets and exceeds the requirements of NFPA 13, 13R and 13D. Fig. 28 satis-fies the UL vertical restraint requirement where needed. UL Listed as a hanger and ver-tical restraint when installed on 3/8" composite wood material. Use two Fig. 27B Speed Nuts when used as a hanger and restraint. Use one Fig. 27B Speed Nut on the upper installed screw when used as a hanger only.

Order by — Figure number and pipe size.

Pat. # 7,455,268, Pat. # 7,832,248


Pipe Approx.

Size A B C Wt.

3/4 31⁄32 2 31⁄2 .180 1 35⁄16 23⁄16 31⁄2 .210 11⁄4 35⁄8 23⁄8 31⁄2 .225 11⁄2 4 21⁄2 31⁄2 .310 2 41⁄2 211⁄16 35⁄8 .340


www.tolco.com43


Fig. 28M - Offset Hanger and Restrainer for

CPVC Plastic Pipe and IPS Pipe

Size Range — 3/4" thru 1-1/4"Material — Carbon Steel, Pre-GalvanizedFunction — Designed to be used as a hanger and restrainer for CPVC piping or steel piping where the “stand-off” design will ease installation by eliminating the need for wood blocking.Features — • Flared edge design protects CPVC pipe from any rough or abrasive surfaces • Unique snap-on design holds pipe firmly in place and allows retrofit type of installation • The “Stand-Off” design eliminates the need for wood block extension • Can be installed on horizontal or vertical piping regardless of mounting surface orientation • Attaches easily to wood structure with two hex head self-threading screws furnished with product • Installs easily using rechargeable electrical driver with 5/16” extension socket eliminating impact tool damage to pipe • Attaches easily to steel, minimum 18 gauge with (2) 1/4” x 1” tek type self drilling tapping screws • cULus Listed as a hanger and a restrainer for fire sprinkler pipingInstallation Note — When installed in wood structural member and threads from the #10 x 1" screws are exposed, use FIG. 27B speed nut to secureApprovals — Underwriters’ Laboratory Listed in the USA (UL) and Canada (cUL) to support automatic fire sprinkler systems. May be installed into wood using fas-teners screws. Meets and exceeds the requirements of NFPA 13, 13R and 13D. Fig. 28M satisfies the UL vertical restraint requirements where needed.Order By — Figure number and pipe size

A

C

B

RESTRAINT

PATENT PENDING

RESTRAINT

Dimensions • Weights Max. Spacing Pipe required per Approx Size A B C NFPA 13 for Wt./100 CPVC plastic pipe

3/4 2 3/16 3-5/16 5’-6” 9 1 2-1/8 3/16 3-1/2 6’-0” 12 1-1/4 2-5/16 3/16 3-1/2 6’-6” 13 HANGER APPLICATION

DETAIL A

TOLCO FIG. 27B(1) REQUIRED

HIGH SIDEOF HANGER

APPLICATIONHANGER AND RESTRAINT

ATOLCO FIG. 27B

(2) REQUIRED


www.tolco.com44


Fig. 29 - Double Offset Hanger & Restrainer for

CPVC Plastic Pipe

Size Range — Available in 3/4" and 1" pipe sizesMaterial — Pre-Galvanized SteelFunction — Intended to perform as a hanger and restrainer for CPVC, plastic fire sprinkler pipe. Provides double offset 1 ½” x 1 ½” from mounting surface. This design will ease installation by eliminating the need for wood block extension and allow retro-fit attachment of hanger to sprinkler pipe.Features — • Thumb tab provides protection to restrain pipe in rough job site conditions. Tab is not required to be bent for listed installation.• Offset edge eliminates abrasion.• Attaches easily to wood structure with two special #10 x 1 hex head self-threading screws furnished with product.• Can be used as a single offset hanger by aligning "dimples" with top of mounting surface and utilizing two fasteners in two of the three holes provided.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL) as a hanger and restrainer to support fire sprinkler systems. Meets and exceeds requirements of NFPA 13, 13R and 13D.Finish — Pre-GalvanizedOrder By — Figure number and pipe size.PATENT PENDING

1.500

1.500

Install using a rechargeable electric drill fi tted with a 5/16” socket attachment with the special hex head self-tapping screws provided. Install screws until they bottom out. Pipe can be “snapped” into hanger before or after installation of the screws to the mounting surface. “Thumb tab” may be bent up to provide additional protection to the pipe, but is not required for performance of the hanger / restrainer function.

Double Offset

Single Offset

1.500

1.500


www.tolco.com45

www.tolco.com

Material — Carbon SteelFunction —Recommended for suspending pipe outward from mounting surface.Approvals — Conforms to Federal Specification WW-H-171E, Type 32 and Manufacturers Standardization Society SP-69, Type 31.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, indicate “A” dimensions, “H” diameter and finish

Fig. 30 - Light Welded Bracket


Max. Rec.

A B C Load Lbs.

9 8 6.5 750 13 12 10.5 750 19 18 16.5 750

Revision 10/24/2007


www.tolco.com46


Max. Recommended Load — (Fig. 30L) 750 lbs., (Fig. 30M) 1500 lbs., (Fig. 30H) 3000 lbs.Material — Carbon SteelFunction — Recommended for supporting pipe on top or hanging through support bracket outward from mounting surface.Approvals — Conforms with the following Federal Specification WW-H-171E and Manufacturers Standardization Society Types: 30L — WW-H-171E, Type 32 and MSS SP-69 Type 31 30M — WW-H-171E, Type 33 and MSS SP-69 Type 32 30H — WW--171E, Type 34 and MSS SP-69 Type 33Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.

Fig. 30L - Welded Bracket - Light Duty

Fig. 30M - Welded Bracket - Medium Duty

Fig. 30H - Welded Bracket - Heavy Duty


Fig. 30L

Hole Max. Rec. Approx.

Sizes A B C Size Load Lbs. Wt./100

1 13 9 111⁄2 9/16 750 571 2 17 13 151⁄2 9/16 750 769 3 23 19 211⁄2 9/16 750 1057




1 18 12 151⁄4 * 11⁄8 3000 2195 2 24 18 211⁄4 21⁄2 11⁄8 3000 4398 3 30 24 271⁄4 21⁄2 11⁄8 3000 6294 4 36 30 33 21⁄2 11⁄8 3000 7196 5 42 36 39 31⁄2 11⁄8 3000 13197 6 50 42 46 31⁄2 11⁄8 3000 15795

* One hole


Fig. 30M

Fig. 30H


Sizes A B C Size Load Lbs. Wt./100

0 18 12 151⁄2 13/16 1500 1577 1 24 18 211⁄2 13/16 1500 2578 2 30 24 271⁄2 13/16 1500 4446


www.tolco.com47

www.tolco.com

Size Range — 1/2" thru 8" pipeMaterial — Carbon SteelFunction —Recommended for suspending pipe outward from mounting surface.Finish — PlainNote — Maximum “L” dimension 1'-4". Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, pipe size, indicate “L” dimension and finish

Fig. 31-M - Welded Knee Bracket

Dimensions

Pipe H Max. Rec.

Size Hole Size Load Lbs.

1/2 - 21⁄2 9/16 1000 3 9/16 1000 31⁄2 9/16 1000 4 11/16 1000 5 11/16 1000 6 11/16 1000 8 11/16 1000

Size Range — 1/2" thru 8" pipeMaterial — Carbon SteelFunction —Recommended for suspending pipe outward from mounting surface.Finish — PlainNote — Maximum “L” dimension 1'-4". Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, pipe size, indicate “L” dimension and finish

Fig. 31-O - “O” Bracket

Dimensions

Pipe H Max. Rec.

Size Hole Size Load Lbs.

1/2 - 21⁄2 9/16 450 3 9/16 450 31⁄2 9/16 450 4 11/16 450 5 11/16 450 6 11/16 450 8 11/16 450

Revision 8/13/2010


www.tolco.com48


Size Range — 1/2" thru 24" pipeMaterial — Carbon SteelFunction — Recommended for anchoring pipe to structure.Finish — PlainNote — 1/2" thru 4", use U-bolt to fasten chair to sup-port; 5" thru 24" U-bolt attaches directly to support struc-ture. Holes are provided in chair for fastening to support if required. Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number and pipe size

Fig. 32 - Anchor Chair


Pipe U-Bolt Approx.

Size Dia. A B C Wt./100

1/2 3/8 15/16 4 13⁄16 80 3/4 3/8 11⁄16 23⁄8 13⁄8 88 1 3/8 13⁄16 25⁄8 13⁄8 96 11⁄4 3/8 13⁄8 27⁄8 21⁄16 107 11⁄2 3/8 19⁄16 31⁄4 23⁄8 118 2 3/8 13⁄4 33⁄8 213⁄16 132 21⁄2 1/2 2 415⁄16 37⁄16 175 3 1/2 23⁄8 59⁄16 41⁄16 215 31⁄2 1/2 23⁄8 61⁄16 49⁄16 240 4 1/2 27⁄8 69⁄16 51⁄16 265


Pipe U-Bolt Approx.

Size Dia. A B C D Wt./100

5 1/2 37⁄16 4 61⁄8 21⁄4 290 6 3/8 4 5 73⁄8 3 315 8 5/8 51⁄4 7 93⁄8 41⁄2 885 10 3/4 67⁄16 8 115⁄8 51⁄2 1050 12 7/8 71⁄2 9 133⁄4 6 1210 14 7/8 83⁄16 10 15 7 1480 16 7/8 91⁄4 10 17 7 1735 18 1 103⁄8 11 191⁄8 7 2011 20 1 113⁄8 12 211⁄8 7 2332 24 1 135⁄8 12 251⁄8 8 2550


www.tolco.com49

www.tolco.com

Size Range — 1/2" thru 2" rodMaterial — Carbon SteelFunction — Structural attachment to concrete ceiling. Use with Fig. 332 Bridge Clevis to attach to center lug.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish

Fig. 33 - Concrete Single Lug Plate


Rod Max. Rec. Approx. Size A B C D H T Load Lbs.* Wt./100

1/2 10 8 9/16 17⁄8 5/8 1/4 1130 1115 5/8 10 8 9/16 2 3/4 1/4 1810 1465 3/4 10 8 11/16 2 7/8 3/8 2710 1478

7/8 10 8 11/16 23⁄4 1 3/8 3770 2195 1 12 8 13/16 23⁄4 11⁄8 1/2 4960 3185 11⁄4 12 8 15/16 4 13⁄8 5/8 8000 4385

11⁄2 12 8 11⁄8 4 15⁄8 3/4 11630 4568 13⁄4 12 8 13⁄8 41⁄4 17⁄8 3/4 15700 5578 2 12 8 13⁄8 41⁄4 21⁄4 3/4 20630 5820

* Based on allowable stresses shown in the ANSI code for pressure piping.

Revision 9/1/2006


www.tolco.com50


Fig. 34 - Concrete Clevis Plate with Pin

Size Range — 3/8" thru 2" rodMaterial — Carbon SteelFunction — Structural attachment to concrete ceiling where flexibility is desired. (Use with Fig. 330 Weldless Eye Nut, Fig. 102 Eye Rod or Fig. 101 Welded Eye Rod.) Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish


Rod Pin Dia. Max. Rec. Approx. Size A B C D E F Load Lbs.* Wt./100

3/8 10 8 9/16 23⁄8 13⁄4 1/2 610 1175 1/2 10 8 9/16 23⁄8 13⁄4 5/8 1130 1185 5/8 10 8 9/16 21⁄2 13⁄4 3/4 1810 1565

3/4 10 8 11/16 21⁄2 21⁄4 7/8 2710 1685 7/8 10 8 11/16 31⁄2 23⁄4 1 3770 1805 1 12 8 13/16 33⁄4 3 11⁄8 4960 3685

11⁄4 12 8 15/16 33⁄4 33⁄4 13⁄8 8000 4085 11⁄2 12 8 11⁄8 5 41⁄2 15⁄8 11630 5975 13⁄4 14 10 13⁄8 51⁄4 51⁄4 17⁄8 15700 9355 2 14 10 13⁄8 51⁄4 51⁄4 21⁄4 20700 10000




www.tolco.com51

www.tolco.com

Fig. 35 - Concrete Rod Attachment Plate

Size Range — 3/8" thru 2" rodMaterial — Carbon SteelFunction — Structural attachment to concrete ceiling where vertical attachment is desired. Attach hanger rod directly to support bracket. Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish


Rod Max. Rec. Approx. Size A B C D Load Lbs.* Wt./100

3/8 10 8 9/16 31⁄4 610 1155 1/2 10 8 9/16 31⁄4 1130 1160 5/8 10 8 9/16 31⁄2 1810 1505

3/4 10 8 11/16 35⁄8 2710 1605 7/8 10 8 11/16 43⁄4 3770 1665 1 12 8 13/16 51⁄4 4960 3485

11⁄4 12 8 15/16 53⁄4 8000 3865 11⁄2 12 8 11⁄8 71⁄2 11630 5635 13⁄4 14 10 13⁄8 9 15700 8805 2 14 10 13⁄8 91⁄2 20700 9215


Revision 10/3/2007



www.tolco.com52


Size Range — 1/2" thru 8" pipeMaterial — Carbon SteelFunction —Recommended for supporting light pipe runs with a 1" offset from mounting surface.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, pipe size and finish

Fig. 40 - Return Line Offset J-Hook


Pipe Size Max. Rec. Load Lbs. Approx. Wt./100

1/2 200 54 3/4 200 55 1 200 78 11⁄4 200 85 11⁄2 200 90 2 200 98 21⁄2 350 126 3 350 136 31⁄2 350 147 4 450 235 5 450 350 6 450 383 8 450 605

Size Range — 1/2" thru 8" pipeMaterial — Carbon SteelFunction —Recommended for supporting light pipe runs.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, pipe size and finish

Fig. 41 - Return Line Straight J-Hook


Pipe Size Max. Rec. Load Lbs. Approx. Wt./100

1/2 200 54 3/4 200 55 1 200 76 11⁄4 200 82 11⁄2 200 87 2 200 96 21⁄2 350 124 3 350 134 31⁄2 350 145 4 450 153 5 450 348 6 450 381 8 450 600


www.tolco.com53

www.tolco.com

Material — Carbon SteelFunction — Recommended for supporting pipe at various distances from wall or column.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, size and finish

Fig. 42 - Angle Bracket

Size Range — 3/8" thru 7/8" rodMaterial — Carbon SteelFunction — Recommended for attaching hanger rod to side of beams or walls.Approvals — 3/8", Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL), and Factory Mutual Engineering approved.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish

Fig. 50 - Side Beam Bracket



Size A B Size Load Lbs. Wt./100

1 3 2 7/16 180 46 2 4 3 7/16 180 65 3 3 2 9/16 390 85 4 4 3 9/16 390 115


Rod Hole Max. Rec. Approx.

Size A B C Size Load Lbs. Wt./100

3/8 2 3/4 2 7/16 700 35 1/2 2 3/4 2 9/16 700 35 5/8 2 3/4 2 11/16 700 32 3/4 21⁄2 3/4 21⁄2 13/16 1250 110 7/8 21⁄2 3/4 21⁄2 15/16 1250 100

Revision 9/1/2006


www.tolco.com54


Size Range — 3/8" and 1/2" rod, 1/2" thru 8" pipeMaterial — Carbon SteelFunction — Recommended for attaching hanger rod to side of beams or walls. Designed to accommodate current rod schedule and fastener requirements per National Fire Protection Association (NFPA) Pamphlet 13.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL), and Factory Mutual Engineering approved.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish

Fig. 51 - Side Beam Bracket for

NFPA Rod and Fastener Sizing


Pipe Rod Hole Size Max. Rec. Approx. Size Size A B C H-1 H-2 Load Lbs. Wt./100

1/2 - 2 3/8 2 3/4 2 7/16 7/16 700 35 21⁄2 - 4 3/8 2 3/4 2 9/16 7/16 700 34 5 - 6 1/2 21⁄2 3/4 21⁄2 9/16 9/16 1250 71 8 1/2 21⁄2 3/4 21⁄2 11/16 9/16 1250 70


www.tolco.com55

www.tolco.com

Size Range — 3/8" and 1/2" rod, 1/2" thru 31⁄2" pipeMaterial — Carbon SteelFunction — Recommended for attaching hanger rod to steel or wood beams. Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish

Fig. 52 - Six Hole Side Beam Bracket


Rod Hole Size Max. Rec. Approx. Size A B C H-1 H-2 H-3 Load Lbs. Wt./100

3/8 x 1/2 2 13/16 2 9/16 7/16 5/16 700 35 1/2 x 1/2 2 3/4 2 9/16 9/16 5/16 700 34

Size Range — 1/2" thru 4" pipe (3/8" rod).Material — Stainless SteelFunction — Recommended for attaching hanger rod to steel or wood beams. Tapped hole allows easy adjustment of hanger rod.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL), and Factory Mutual Engineering approved for 1/2" thru 4" pipe.Note — Available only in Stainless Steel materials. Order By — Figure number, rod size and stainless steel finishNote — Per NFPA 13: 1/2" thru 2" pipe use 3/8" fastener; 21⁄2" thru 4" pipe, use 1/2" fastener.

Fig. 56 - Tapped Side Beam Connector, in Stainless Steel


Pipe Rod Size Hole Size Approx. Size A B C D G H Wt./100

1/2 - 4 3/8 25⁄8 1 11⁄4 7/16 9/16 20

Revision 10/24/2007


www.tolco.com56


Size Range — 3/8" rod, pipe sizes 1/2" thru 4"Material — Pre-Galvanized SteelFunction — Practical and economical bracket used to support piping from wood, concrete or steel beams.Features — Unique design allows rod to be easily threaded into bracket. Offset design permits unlimited rod adjustment. Center mounting hole will accept 3/8" and 1/2" fastener bolts. Per NFPA 13: 1/2" thru 2" pipe requires 3/8" fastener, 21⁄2" thru 4" pipe requires 1/2" fastener.*Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL), and Factory Mutual Engineering approved thru 4" pipe.*Note — Additionally UL has listed the Fig. 58 with fasteners as shown in table below.Finish — PlainNote — Available in Electro-Galvanized finish. Order By — Figure number and finish

Fig. 58 - Threaded Side Beam Bracket

UL Listed Fastener Table

Pipe Size Qty. Fastener Type Material

2 2 #16 x 2 Drive Screws Wood 2 1 3/8 Lag Bolt Wood 21⁄2 - 4 1 1/2 Lag Bolt Wood 31⁄2 2 1/4 x 11⁄2 Lag Bolt Wood 4 2 1/4 x 2 Lag Bolts* Wood 4 2 1/4 x 1 tek screws 14 gauge 4 2 1/4 x 1 tek screws 16 gauge

* No pre-drilling required



Size Size A B C Load Lbs.* Wt./100

1/2 thru 4 3/8 23⁄4 11⁄2 11⁄8 300 14

* With safety factor of 5.


www.tolco.com57

www.tolco.com

Size Range — 3/4" thru 6" pipeMaterial — Carbon SteelFunction — Recommended for use on top flange of standard I-beams, wide flange beams and roof trusses where the flange thickness does not exceed 0.81".Installation — Slide steel clip against beam flange and attach hook rod and I-rod (Fig. 102). Tighten hook rod and I-rod (Fig. 102). Hammer clip firmly against the underside of the beam to complete the installation.Features — The clamp holds firmly to the beam provid-ing an efficient and economical means of supporting small piping from the top flange of steel beams and roof trusses.Maximum Temperature — 650°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, flange width and flange thickness

Fig. 60 - Top Beam Clamp

Material — Carbon SteelFunction — Designed to hook onto top flange of beam or angle truss. The support rod completes assembly and secures it to flange.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.

Fig. 61 - Top Beam Hook

Dimensions

Hook Rod I-Rod (Fig. 102) Max. Rec.

Pipe Size Diameter A Load Lbs.

3/4 - 2 3/8 3/8 610 21⁄2 - 31⁄2 1/2 1/2 940 4 - 5 1/2 5/8 940 6 1/2 3/4 940

Dimensions

Max. Rec.

Type A B C Load Lbs.

1 3/8 5/16 1 300 2 1/2 3/8 1 500 3 5/8 7/16 1 700 4 3/4 1/2 11⁄2 1000 5 7/8 9/16 11⁄2 2000

Revision 9/1/2006


www.tolco.com58


Size Range — 3/8" thru 1/2" rod sizesMaterial — Carbon SteelFunction — Designed to hook on top chord of metal bar joist. Hanger rod is threaded into product and secured with a wash-er and nut.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL) for up to 4" pipe with 3/8" rod, up to 6" pipe with 1/2" rod.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size, width and thickness of bar joist. Threaded hole will be center of that width.

Fig. 61T - Bar Joist Hanger

Dimensions

Pipe Rod Max. Rec.

Size Size Load Lbs.

Up to 4 3/8 300 6 1/2 600


www.tolco.com59

www.tolco.com

Material — Carbon SteelFunction — Recommended for the suspending of hanger rod from the center of an I-beam, equally distributing the load on both sides of the beam. Use with Fig. 102 Eye Rod, Fig. 101 Welded Eye Rod or Fig. 330 Weldless Eye Nut.Approvals — Conforms to Federal Specification WW-H-171E, Type 21, and Manufacturers Standardization Society SP-58, Type 21.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, type, width of flange and finish.

Fig. 62 - Center Load Beam Clamp

Dimensions

Max. Rec.

Type A B* Bolt Size Load Lbs.

1 1/2 13⁄8 3/8 1000 2 1/2 13⁄8 1/2 1250 3 5/8 19⁄16 1/2 1500 4 3/4 21⁄4 5/8 3000 5 3/4 21⁄4 5/8 3250 6 3/4 25⁄16 3/4 3500

* Not applicable for type 1 — 2" and type 3 — 2" flange widths.

Dimensions • Weights Flange Max. Flange Approx. Wt./100

Width Thickness Type 1 Type 2 Type 3 Type 4 Type 5 Type 6

2 7/16 66 85 — — — — 3 1/2* 75 95 151 355* — — 4 1/2 91 114 163 382 470 634 5 5/8 100 125 187 435 536 667 6 3/4 115 143 216 452 558 728 7 7/8 129 16 242 484 606 767 8 7/8 144 177 267 510 659 861 9 1 159 196 295 583 721 913 10 1 172 210 319 625 773 982 11 1 185 227 343 667 826 1048 12 1 198 243 367 709 879 1115

* Maximum flange thickness type 1, 2 and 3 = 7/16"

Revision 1/24/2007


www.tolco.com60


Size Range — 3/8" thru 7/8" rodMaterial — Carbon SteelFunction — For attachment to I-beams, channels, and wide flange beams where the thickness does not exceed 3/4". Hardened set screw secures “C” Clamp to beam.Approvals — Conforms to Federal Specification WW-H-171E, Type 23 and Manufacturers Standardization Society SP-69, Type 23.Finish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. Order By — Figure number, rod size and finish

Fig. 64 - Steel “C” Clamp with Locknut


Max. Pipe Rod Size Max. Rec. Approx.


2 3/8 23⁄8 23⁄8 1 400 40 31⁄2 1/2 23⁄8 23⁄8 1 400 50 5 5/8 23⁄8 23⁄8 1 550 70 6 3/4 25⁄16 23⁄8 1 630 83 *8 7/8 35⁄16 3 13⁄8 1200 158

* Throat opening is 1".


www.tolco.com61

www.tolco.com

Fig. 65 and Fig. 66

Reversible C-Type Beam Clamps 3/4" and 11⁄4" Throat Openings

Size Range — (Fig. 65 and Fig. 66) 3/8", 1/2" and 5/8" rodMaterial — Carbon Steel with hardened cup point set screw and jam nutFunction — Recommended for hanging from steel beam where flange thickness does not exceed 3/4" (Fig. 65) or 11⁄4" (Fig. 66).Features — All steel construction eliminates structural deficiencies associated with casting type beam clamps. May be used on top or bottom flange of the beam. (Beveled lip allows hanging from top flange where clearance is limited.) May be installed with the set screw in up or down position. Offset design permits unlimited rod adjustment by allowing the rod to be threaded completely through the clamp. Open design permits inspection of thread engagement.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL). Exceeds requirements of the National Fire Protection Association (NFPA), Pamphlet 13, 3/8" rod will support 1/2" thru 4" pipe, 1/2" rod will support 1/2" thru 8" pipe. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Finish — PlainNote — Available in Electro-Galvanized and HDG finish. Order By — Figure number, rod size and finish

Fig. 65 Patent #4,570,885


Rod Size Max. Rec. Approx. A B C D E F Load Lbs.* Wt./100

3/8 13⁄16 3/4 1 7/16 1 610 28 1/2 11⁄2 3/4 1 9/16 11⁄4 1130 55 5/8 11⁄2 3/4 1 9/16 11⁄4 1130 55

* Max. loads for clamp with set screw in up or down position.

Fig. 65


Rod Size Max. Rec. Approx. A B C D E F Load Lbs.* Wt./100

3/8 13⁄16 11⁄4 1 7/16 1 610 28 1/2 11⁄2 11⁄4 1 9/16 11⁄4 1130 55 5/8 11⁄2 11⁄4 1 9/16 11⁄4 1130 55

* Max. loads for clamp with set screw in up or down position.

Fig. 66


Revision 9/1/2006


www.tolco.com62


Size Range — 3/8" and 1/2" rod sizesMaterial — All Stainless Steel (T-316 or T-304)Function — Recommended for hanging from steel beams where flange thickness does not exceed 3/4" (Fig. 67SS) or 11⁄4" (Fig. 68SS).Features — All steel construction eliminates structural deficiencies associated with casting type beam clamps. May be used on top or bottom flange of the beam. May be installed with the set screw in up or down position. Offset design permits unlimited rod adjust-ment by allowing the rod to be threaded completely through the clamp.Approvals — Underwriters’ Laboratories LIsted in the USA (UL) and Canada (cUL). Conforms to Manufacturers’ Standardization Society SP-69, Type 19. Meets or exceeds requirements of the National Fire Protection Association (NFPA), pamphlet 13, 3/8" rod will support 1/2" through 4" pipe, 1/2" rod will support 1/2" through 8" pipe.Order By — Figure number and rod size

Fig. 67SS and Fig. 68SS Stainless Steel Reversible

C-Type Beam Clamps 3/4" Throat Opening/Wide Mouth

Stainless Steel

Fig. 67SS

Fig. 67SS

Fig. 68SS


Pipe Test Approx.

Size A B C D E F G Load Wt./100

1/2 - 4 3/8 3 7/8 1 15⁄8 15⁄8 11⁄8 1500 lbs. 68 5, 6, 8 1/2 3 7/8 1 15⁄8 15⁄8 11⁄8 4050 lbs. 107


Pipe Test Approx. Size A B C D E F Load Wt./100

1/2 - 4 3/8 21⁄16 2 3/4 11⁄4 11⁄8 1500 lbs. 84 5, 6, 8 1/2 21⁄4 21⁄4 13/16 11⁄4 11⁄4 4050 lbs. 170


www.tolco.com63


Size Range — 3/8" thru 3/4" rodMaterial — Carbon SteelFunction — For attachment to structural shapes requiring wider throat especially under roof with bar joist construc-tion. This clamp may be used in the set screw in down position only.Approvals — Conforms to Federal Specification WW-H-171E, Type 23 and Manufacturers Standardization Society SP-69, Type 19.Finish — PlainNote — Available in Electro-Galvanized finish. Order By — Figure number, rod size and finishNote — Do not over tighten set screw.

Fig. 68 - Wide Throat Top Beam “C” Clamp w/Locknut


Rod Max. Rec. Approx. Size Load Lbs. Wt./100

3/8 400 34 1/2 500 50 5/8 600 53 3/4 800 86


www.tolco.com64


AVAILABLE 2009Fig. 68S and 68W - Malleable, Reversible

Beam Clamps 3/4" and 1-1/4" Throat Openings

Dimensions • Weights Max Rec.

Rod Max. Rec.

Load Lbs. Approx.

Size A B C D E F Load Lbs. Set screw Wt./100

Set screw up

down

3/8 3/8 1-1/2 3/4 1-1/8 7/16 7/8 610 610 32 1/2 3/8 1-5/8 3/4 1 7/16 1-1/8 750 1130 54 5/8 1/2 1-9/16 3/4 1 9/16 1-1/8 750 1130 50 3/4 1/2 1-3/4 3/4 1-1/8 9/16 1-1/4 750 1130 81 7/8 1/2 1-3/4 3/4 1-1/8 9/16 1-5/16 750 1130 75

Size Range — 3/8" thru 7/8" rodMaterial — Cast Malleable Steel with hardened cup point set screw and jam nutFunction — Recommended for hanging from steel beam where flange thickness does not exceed 3/4" (Fig. 68S) or 1-1/4" (Fig. 68W)Features — May be used on top or bottom flange of the beam. Beveled lip allows hanging from top flange where clearance is limited. may be installed with the set screw in the up or down position. Offset design permits unlimited rod adjustment by allowing the rod to be threaded completely through the clamp. The rear window design permits inspection of thread engagement.Approvals — Factory Mutual Engineering Approved. Underwriters Laboratories Listed. Conforms to Federal Specification WW-H-171E, Type 23 and Manufacturers Standardization Society SP-58, Type 19. Fig. 68S 3/8" is cULus Listed to support up to 4" pipe with the set screw in the down position, up to 3" pipe with the set screw in the up position. Fig. 68S 1/2" is cULus Listed to support up to 8" pipe with the set screw in the down position, up to 6" pipe with the set screw in the up position. Fig. 68W 3/8" is cULus Listed to support up to 4" pipe with the set screw in the down position, up to 4" pipe with the set screw in the up position. Fig. 68W 1/2" is cULus Listed to support up to 6" pipe with the set screw in the down position, up to 6" pipe with the set screw in the up position. Factory Mutual Engineering approved only with the set screw in the down position.Finish — PlainNote — Available in Electro-Galvanized and HDG finishOrder By — Figure number, rod size & finish

Dimensions • Weights Max Rec.

Rod Max. Rec.

Load Lbs. Approx.

Size A B C D E F Load Lbs. Set screw Wt./100

Set screw up

down

3/8 3/8 1-9/16 1-1/4 1-1/8 7/16 13/16 610 610 41 1/2 1/2 1-9/16 1-1/4 1 5/8 1-1/8 750 1130 66 5/8 1/2 1-1/2 1-1/4 1 9/16 1-1/8 750 1130 68 3/4 1/2 1-3/4 1-1/4 1-1/8 3/8 1-1/4 750 1130 110 7/8 1/2 1-3/4 1-1/4 1-1/8 9/16 1-5/16 750 1130 98

Fig. 68W

Fig. 68S


www.tolco.com65

www.tolco.com

Fig. 69 - Beam Clamp Retaining Strap

Type Rod Size A Hole Size B

1 3/8 7/16 Specify 1/2 9/16 Specify 2 5/8 11/16 Specify 3/4 13/16 Specify 3 3/8 - 7/8 Specify Specify

* Longer lengths are available, consult factory.

B

Size Range — 3/8" thru 7/8" rod by 4" thru 16" length.*Material — Pre-Galvanized SteelFunction — To offer more secure fastening of various types of beam clamps to beam where danger of movement might be expected. NFPA 13 requires the use of retaining straps with all beam clamps installed in earthquake areas. Satisfies requirements of NFPA 13.Important Note — Good installation practice of a retaining strap requires that the strap be held tightly and securely to all component parts of the assembly. Therefore a locking mech-anism of some kind such as a hex nut or the beveled locking slot on the TOLCO® Fig. 69R will provide a more secure reliable installation.Approvals — Underwriters’ Laboratories listed in the USA (UL) and Canada (cUL). Approved for use with any listed beam clamp. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relat-ing to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Finish — Pre-GalvanizedOrder By — Figure number, type, length “B” and rod size being used with beam clampNote — Minimum return on Strap: 1".

Dimensions


Revision 9/15/2010


www.tolco.com66

www.tolco.com

Fig. 69R - Retrofit Capable Beam Clamp

Retaining Strap

Revision 4/13/2010

Size Range — 3/8" and 1/2" rod; 4" thru 16" length.Material — Pre-Galvanized SteelFunction — To offer more secure fastening of various types of beam clamps to beam where danger of movement might be expected. NFPA 13 requires the use of retaining straps with all beam clamps installed in earthquake areas. Satisfies requirements of NFPA 13.Features — Beveled locking slot* is precisely formed to align with the threaded section of a hanger rod or set screw and engage the unit securely. May be used as shown in section “A-A” or inverted. Allows easy installation for new construc-tion or retrofit applications.Important Note — Good installation practice of a retaining strap requires that the strap be held tightly and securely to all component parts of the assembly. Therefore, a locking mechanism of some kind, such as the beveled locking slot of the Fig. 69R or a hex nut tightened against other types of retaining straps will provide a more secure and reliable instal-lation.Approvals — Underwriters’ Laboratories listed in the USA (UL) and Canada (cUL). Approved for use with any listed beam clamp. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relat-ing to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines.Finish — Pre-GalvanizedOrder By — Figure number, rod or set screw size and lengthNote — Minimum return on Strap: 1".

* Patent #5,947,424Dimensions

Rod Size A Length

3/8" Specify 1/2" Specify



www.tolco.com67

www.tolco.com

FIG. 70

FIG. 70R

FIG. 70S

FIG. 71

Size Range — 1/4" thru 11⁄2" rodMaterial — Carbon SteelFunction — Used for coupling two threaded rods together of equal or reduced rod sizes, with or without inspection hole.Finish — Electro-GalvanizedNote — Available in HDG finish or Stainless Steel materials.

Fig. 70 - Steel Rod Coupling

Fig. 70R - Steel Reducing Rod Coupling

Fig. 70S - Short Pattern Steel Rod Coupling

Fig. 71 - Steel Window Rod Coupling


Rod Max Rec. Approx.

Size Length Load Lbs. Wt./100

1/4 7/8 240 2 5/16 13⁄4 300 13 3/8 13⁄4 610 11 1/2 13⁄4 1130 11 5/8 21⁄8 1810 16 3/4 21⁄4 2710 27 7/8 21⁄2 3770 57 1 23⁄4 4960 70

11⁄8" - 11⁄2" — Consult factory for specifications

Fig. 70




3/8 x 1/4 7/8 240 4 1/2 x 3/8 11⁄4 610 7 5/8 x 1/2 21⁄8 1130 14 3/4 x 5/8 21⁄4 1810 21 7/8 x 3/4 21⁄2 2710 40

Fig. 70R




3/8 11⁄8 610 4 1/2 11⁄4 1130 6

For rod sizes 5/8" to 1" - consult factory

Fig. 70S/Fig. 71

Revision 4/13/2010


www.tolco.com68

www.tolco.com

Fig. 75 - Swivel Attachment

Size Range — 3/8" Rod AttachmentMaterial — Carbon SteelFunction — There are three recommended applications for this product: May be used as a Branch Line Restraint for structural attachment to anchor bolt, beam clamp, etc. May be used in a pitched or sloped roof application, to meet requirements of NFPA 13 (2010) 9.1.2.6. May be used as an upper attachment with short hanger rod to omit seismic bracing (per UBC97).Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL) to support up to 4" pipe. Meets requirements of Uniform Building Code (UBC) 1997 Table O, Section 3.B.Finish — Electro-GalvanizedOrder By — Figure numberPATENT PENDING

Revision 3/10/2010

May be used as a structural attachment component of a branch line restraint


www.tolco.com69


B

D(2)

E

C A

Size Range — 3/8" rodMaterial — Pre-Galvanized Steel Features — Attachment to wood beams, ceilings, metal decks or walls. Can also be welded to steel beams.Approvals — Underwriters’ Laboratories Listed in the USA (UL) and Canada (cUL). Additionally, (UL) has listed the Fig. 78 with fasteners as shown in the table below.Finish — PlainNote — Available in Electro-Galvanized and HDG finish. Order By — Figure number, rod size and finish

Patent #5,702,077

Fig. 78 - All Steel Ceiling Plate

UL Listed Fastener Table

Pipe Size Qty Fastener Type Material

1/2 - 2 2 #14 x 11⁄4 A-point hex-washer-head sheet metal screw Wood 21⁄2 - 4 2 1/4 x 11⁄2 wood screws* Wood 1/2 - 2 2 1/4 x 1 tek screws Metal (18 gauge) 1/2 - 2 2 #14 x 11⁄4 A-point hex-washer-head sheet metal screw Wood 1/2 - 2 2 #14 x 2 A-point-hex-washer-head sheet metal screw Wood thru 5/8" gyp board

* No pre-drilling


Max. Rec. Approx. Pipe Size A B C D E Load Lbs.* Wt./100

1/2 - 2 3 21⁄8 11⁄8 5/16 3/8 150 15 5 - 6 Consult factory for data

* Minimum safety factor of 5


www.tolco.com70

www.tolco.com

Fig. 81 - Epoxy Copper Tec™ Tubing Clevis Hanger

Fig. 81PVC - PVC Coated Copper Tec™ Tubing Clevis HangerSize Range — Size1/2" thru 6" copper tubingMaterial — Carbon SteelFunction — Recommended for the suspension of non-insulated copper tubing line.Approvals — Conforms to Federal Specification WW-H-171E, Type 12 and Manufacturers Standardization Society SP-69 Type 1.Finish — Epoxy Copper Tec™ PlatedNote — Available with plastic coating, specify by ordering Fig. 81PVCOrder By — Figure number and nominal tubing size

A

B

C

D




1/2 3/8 25⁄8 111⁄16 5/8 150 27 3/4 3/8 25⁄8 111⁄16 5/8 250 29 1 3/8 27⁄8 113⁄16 3/4 250 32 11⁄4 3/8 3 17⁄8 13/16 250 34 11⁄2 3/8 35⁄8 25⁄16 11⁄16 250 36 2 3/8 41⁄2 3 15⁄8 250 44 21⁄2 1/2 6 31⁄4 21⁄8 350 96 3 1/2 61⁄8 37⁄8 2 350 105 31⁄2 1/2 65⁄8 41⁄4 113⁄16 350 110 4 1/2 71⁄16 43⁄8 19⁄16 400 151 5 1/2 81⁄2 55⁄16 17⁄8 550 220 6 5/8 93⁄4 59⁄16 111⁄16 550 265

Fig. 81

Fig. 81PVC

Revision11/16/2010


www.tolco.com71


Fig. 82 - Epoxy Copper Tec™ Tubing Riser Clamp

Fig. 82PVC - PVC Coated Copper Tec™ Tubing Riser Clamp

Size Range — Size1/2" thru 6" copper tubingMaterial — Carbon SteelFunction — Used for supporting vertical copper tubing.Approvals — Conforms to Federal Specification WW-H-171E, Type 8 and Manufacturers Standardization Society SP-69 Type 8.Finish — Epoxy Copper Tec™ PlatedNote — Available with plastic coating, specify by ordering Fig. 82PVCOrder By — Figure number and nominal tubing size

A

Fig. 82

Fig. 82PVC



Size A Bolt Size Load Lbs. Wt./100

1/2 61⁄2 3/8 75 68 3/4 91⁄4 3/8 75 69 1 93⁄8 3/8 120 95 11⁄4 95⁄8 3/8 150 101 11⁄2 10 3/8 150 152 2 10 3/8 150 164 21⁄2 11 3/8 300 172 3 111⁄2 3/8 300 184 31⁄2 12 3/8 300 196 4 13 3/8 300 247 5 14 1/2 400 258 6 15 1/2 500 405


www.tolco.com72

www.tolco.com

Fig. 83 - Isolator for Copper Tubing

Fig. 84 - I.P.S. IsolatorSize Range — Fig. 83 - 3/8" thru 4" copper tubing; Fig. 84 - 3/8" thru 8" pipeMaterial — Pre-Galvanized steel and feltFunction — A non-conductive felt lining serves to prevent electrolysis, damp-en sound vibration and prevent transmission of sound to the building structure.Finish — Pre-GalvanizedStandard Steel Pipe Hangers for use with Isolators: Fig. 1 Clevis Hanger, Fig. 2 Band Hanger, Fig. 3 J-Hanger and TOL-Strut® Rigid or O.D. Pipe ClampsOrder By — Figure number and nominal tube size


Copper Tube Hanger TOL-Strut® Approx. Size A B C Size Clamp Size Wt./100

3/8 1 11⁄4 21⁄4 3/4 11⁄8 O.D. 4 1/2 11⁄8 11⁄4 21⁄4 3/4 11⁄8 O.D. 4 3/4 13⁄8 11⁄4 21⁄4 1 1 RIGD 4 1 15⁄8 11⁄4 21⁄4 11⁄4 11⁄2 O.D. 6 11⁄4 17⁄8 11⁄4 21⁄4 11⁄2 13⁄4 O.D. 1 11⁄2 21⁄8 11⁄4 21⁄4 2 21⁄8 O.D. 10 2 25⁄8 11⁄4 21⁄4 21⁄2 25⁄8 O.D. 12 21⁄2 31⁄8 11⁄4 21⁄4 3 31⁄8 O.D. 13 3 35⁄8 11⁄4 21⁄4 3 3 RIGD 15 31⁄2 41⁄8 11⁄4 21⁄4 31⁄2 31⁄2 RIGD 28 4 51⁄8 11⁄4 21⁄4 5 5 O.D. 44

Fig. 83


Pipe Hanger TOL-Strut® Approx. Size A B C Size Clamp Size Wt./100

3/8 11⁄8 11⁄4 21⁄4 1 1 RIGD 4 1/2 13⁄8 11⁄4 21⁄4 1 1 RIGD 4 3/4 11⁄2 11⁄4 1⁄4 11⁄4 11⁄4 O.D. 6 1 113⁄16 11⁄4 21⁄4 11⁄2 11⁄2 O.D. 10 11⁄4 21⁄8 11⁄4 21⁄4 2 2 O.D. 10 11⁄2 23⁄8 11⁄4 21⁄4 2 2 RIGD 12 2 27⁄8 11⁄4 21⁄4 21⁄2 21⁄2 RIGD 14 21⁄2 33⁄8 11⁄4 3 3 3 O.D. 20 3 4 11⁄4 3 31⁄2 31⁄2 RIGD 25 31⁄2 41⁄2 11⁄4 3 4 4 RIGD 36 4 51⁄2 11⁄4 31⁄2 5 5 RIGD 65 5 61⁄2 11⁄4 4 6 6 RIGD 67 6 75⁄8 21⁄8 51⁄2 8 75⁄8 O.D. 196 8 95⁄8 21⁄8 51⁄2 10 95⁄8 O.D. 210

Fig. 84

Revision 9/1/2006


www.tolco.com73


Size Range — Secures 3/8" thru 7/8" hanger rodMaterial — Carbon SteelFunction — Secures channel to hanger rod for vertical seismic bracing.Approvals — Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems GuidelinesFinish — Electro GalvanizedNote — Available in HDG finish or Stainless Steel materials.Order By — Figure number

Fig. 98 - Rod Stiffener

Fig. 98B - Rod Stiffener w/Break-off Bolt Head

Fig. 99 - All Thread Rod Cut to Length

Size Range — Secures 3/8" thru 7/8" rod in 1" incrementsMaterial — Carbon SteelMaximum Temperature — 750°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, rod diameter, rod length and finish

Max Rec. Load Lbs. Rod For Service Temps Approx.

Size 650°F Wt./100

3/8 730 29 1/2 1350 53 5/8 2160 84 3/4 3230 123 7/8 4480 169 1 5900 222

11⁄4 9500 360 11⁄2 13800 510



Size Range — Secures 3/8" thru 11⁄2" rod in 10’ lengthsMaterial — Carbon SteelMaximum Temperature — 750°FFinish — PlainNote — Available in Electro-Galvanized and HDG finish or Stainless Steel materials.Order By — Figure number, rod diameter and finish

Dimensions

Rod Max. Rec. Load Lbs. Size For Service Temp

650°F

3/8 730 1/2 1350 5/8 2160 3/4 3230 7/8 4480

Fig. 100 - All Thread Rod Full Length

FIG. 98B

FIG. 98

clevis hanger

Documents