classic performance products, inc. …...1970 camaro, and 1968 camaro convertible went along for the...
TRANSCRIPT
378 E. Orangethorpe AvenuePlacentia, CA • 92870
PRESORTED
BOUND PRINTED MATTER
U.S. POSTAGE
PAIDBUENA PARK, CA
PERMIT NO. 88
CLASSIC PERFORMANCE PRODUCTS, Inc.
$5.00
PRODUCT CATALOG
CLASSICPERFORM.COM | 800.522.5004
• CHEVY TRUCK • CHEVY TRI-FIVE & FULLSIZE • CAMARO • NOVA • CHEVELLE • EL CAMINO • • FORD CAR & TRUCK • G-BODY • CADILLAC • LINCOLN • MOPAR •
CLASSICPERFORM.COM | 800.522.5004
CLASSIC PERFORMANCE PRODUCTS, INC.
CLASSIC PERFORMANCE PRODUCTS, INC.
CLA
SSIC
PER
FOR
MA
NC
E P
RO
DU
CTS
, INC
.
PR
OD
UC
T CATA
LOG
#21
#21CATALOG
378 E. ORANGETHORPE AVENUE PLACENTIA, CA 92870 •
www.classicperform.com toll free 800.522.5004
Feeling Social?
Reach Us At:
Phone Line:(714) 522-2000
Fax Line:(714) 522-2500
Email:[email protected]
Mailing Address:378 E. Orangethorpe Avenue
Placentia, CA 92870
WE ARE HERE TO HELP!
Check out our blog @http://classicperformanceproducts.blogspot.com/
24 Hours a Day... 7 Days a Week!TECH GUIDES
INSTRUCTION SHEETSMAGAZINE STORIES
ETC.!
Classic Performance Products, Inc. 714.522.2000 | fax 714.522.2500 378 E. Orangethorpe Ave. | Placentia, CA 92870 | www.classicperform.com
Steering, Brake & Suspension Specialists
Rev. 4/9/2013
#7081PTSBK & #7081PTSBK-U Instructionsfor 1970-81 Rear Pro-Touring Sway Bar
Instructions:1. Coat the sway bar pivot bushing with the supplied grease.
2. Install the pivot bushings onto the sway bar. Refer to the illustration below as needed.
3. Position the sway bar mounting brackets around the bushings.
4. Assemble the axle portion of the sway bar mount around the axle and loosely attach the sway bar to the rear axle. The dip in the sway bar will be down and toward the rear.
5. Position the end link mounts on the bottom of the chassis. The mounts will be on the flat portion of the chassis above the sway bar end, and a little wider than the sway bar. Locate the mounts flush to the end of the slot on the bottom of the chassis. (The nut tab will be inserted through this slot).
6. Using the mounts as a guide drill 3/8” holes into the bottom portion of the chassis.
7. Insert the nut tabs through the slot and into the chassis. Using the 3/8” hardware, bolt the mounting flanges to the chassis.
8. Assemble the end links. Thread the thin nuts onto each of the male rod ends, then the thread the female rod ends onto the male rod ends.
9. Using the 7/16” hardware and spacer bolt the end link assemblies to the sway bar and mounting brackets.
10. Tighten the thin nuts against the female rod ends.
11. Tighten the axle clamps and sway bar pivot mounts to the axle.
12. Be sure to road test the car so you can familiarize yourself with the cars’s new handling characteristics.
1/4″ grade 5 10lb/ft 1/4″ grade 8 14lb/ft5/16″ grade 5 19lb/ft 5/16″ grade 8 29lb/ft3/8″ grade 5 33lb/ft 3/8″ grade 8 47lb/ft7/16″ grade 5 54lb/ft 7/16″ grade 8 78lb/ft1/2″ grade 5 78lb/ft 1/2″ grade 8 119lb/ft9/16″ grade 5 114lb/ft 9/16″ grade 8 169lb/ft5/8″ grade 5 154lb/ft 5/8″ grade 8 230lb/ft
GENERAL TORQUE SPECIFICATIONS:
© Classic Performance Products, Inc. 2013All rights reserved. This document may not be reproduced without prior written permission of CPP.
www.classicperform.com@VISIT OUR WEBSITE:
How Are We Doing?
As we are always striving to make your experience with CPP better, we would love to hear how we are doing. Send in your comments...if you have had a great experience, bad one, or just mediocre...please let us know.
Please mail to:Classic Performance Products, Inc.
Attn: CPP Feedback378 E. Orangethorpe Avenue
Placentia, CA 92870
Or e-mail: [email protected](use “Feedback” in the subject line)
Order by Phone...Pick up at Will Call
Do you live in our area or planning a trip
to come visit? Save yourself some time
in line and place your parts order over the
telephone. Be sure to tell your salesman that you will be coming to pick it up and we will have your ordering waiting for you at
Will Call. Save time and money on shipping costs!
SHOWROOM HOURS:Monday - Friday 8:00am - 5:00pm
Saturday 8:00am - 1:30pm
Note: Due to the variances in the manufacture of after-market products and/or original equipment, production run changes, multiple suppliers of the same product(s) and almost limitless options for such parts, it is the ultimate responsibility of you (the buyer/consumer) to confirm in advance that such part(s) will fit your vehicle.
DAMAGE OR SHORTAGESMake certain you inspect all packages in the presence of the driver/carrier. If you receive a package that has been damaged or opened, make a claim with the driver/carrier at that time. All claims of loss, concealed damaged, damage or other destruction must be made by you with the carrier. Save all boxes and packing materials, as the carrier may want to inspect it. We apologize for this inconvenience - but this is our carrier’s shipping policy. Any shortages not the fault of the carrier must be reported within 5 days of receiving order. No exceptions allowed.
RETURNS Merchandise may be returned or exchanged within the first 30 days of purchase. We do not take returns or exchanges after 30 days. How to return a Product:
1. Customer must request a Return Merchandise Authorization number (RMA) by contacting us via phone or online at www.classicperform.com/returns
2. Return part in the original box and packaging with the RMA number marked on the box.
3. Include a written explanation of the reason for return and copy of the original receipt.
4. Customer is responsible for all shipping costs, regardless of the carrier. We strongly suggest you use UPS, Fedex or USPS with tracking number and insurance to protect yourself against loss or damages.
All returns are subject to inspection before a replacement or credit is issued. We do not issue cash refunds. A 20% restocking fee may be applied, unless a new order is placed with a value of $25 more than the returned order or by choosing store credit. Parts that have been installed, painted, abused or modified will not be accepted for return and may be sent back to the customer. Electrical and special ordered parts are non-refundable.
WARRANTYAll CPP products are guaranteed for life from date of purchase, to be free of defects in materials and workmanship. This guarantee is void in the event of misuse, neglect, improper installation or misdiagnosis. At our option, we will repair or replace any product found to be defective subject to our inspection and approval. Warranty returns require the same procedures as above. All sus-pected defective item must be authorized prior to return; they must have a Return Merchandise Authorization (RMA) number, the original invoice, a brief description of the problem (“defec-tive” is not sufficient) and customer must prepay shipping. Parts that are disassembled, altered, modified, disfigured, or abused will not be covered by our warranty. This warranty does not cover reimbursement of labor costs or incidental damages (if any). There
are no refunds on shipping costs, electrical parts, or special order merchandise.
PRODUCT CHANGESWe are constantly updating and revising our products to bring you the best quality parts available. CPP reserves the right to make changes and improvements without notification. We have no liabil-ity to update previously sold items.
CORE CHARGES/DEPOSITS The purpose of a core deposit / charge is to insure the return of rebuildable parts. Your deposit will be promptly refunded when we receive your complete, rebuildable core. A copy of your original purchase invoice must accompany your core. No refund will be issued for broken, damaged, disassembled or incomplete cores. No exceptions will be allowed. All cores must be prepaid by customer and returned within 30 days of purchase to obtain full core value. Cores not returned within 30 days will receive only one half (1/2) of core value. Unless cores are returned within a timely fashion, other customers will have to wait.
LIABILITY The seller, CPP, hereby expressly disclaims all warranties, either expressed or implied warranty or merchant ability of fitness for a purpose, and CPP neither assumes nor authorizes any other person to assume for it any liability in connection with the sale of this mer-chandise. CPP will be responsible only for “the products sold by us.” Sellers and manufacturers only obligation shall be to replace such quantity of the product proved to be defective by CPP. Neither seller nor manufacturer shall be liable for any loss, injury or dam-age, direct or consequential, arising out of the use of, or the inabil-ity of product. After use, the user shall assume all risk and liability whatsoever in connection thereof. For out of country, it is the responsibility of the consumer to research the requirement of their local authorities and how local policies may apply to the use of our products prior to purchase and installation.
PRICING, TERMS, CONDITIONS CPP reserves the right to change prices, terms, specifications and other information without notice. Please call or write us if you have any questions or you feel there is a discrepancy.
NOTICE: © Copyright Classic Performance Products, Inc. 2015. All Rights Reserved. This publication, in whole or in part, may not be reproduced, stored in a computerized, or other retrieval system or transmitted in any form, or by any means whatsoever without the prior written permission of Classic Performance Products, Inc.
Steering | Brakes | Suspension Toll Free: (800) 522-5004 • www.classicperform.com
Steering | Brakes | Suspension Steering | Brakes | Suspension
CHEVROLET TRUCK 4
FORD CAR & TRUCK 58
CHEVY FULLSIZE 94
NOVA / CAMARO 136
CHEVELLE / EL CAMINO 182
G-BODY 218
OTHER CUSTOMS 234
MUSTANG II 248
UNIVERSAL 264
POPULAR UPGRADES 292
NEW PRODUCTS N1-N24
TECHNICAL INFO 328
POLICIES 360
LS CONVERSION 256
We made our way back east to Memphis, Tennessee, to participate at the 2017 F-Body Nationals. Our CPP project vehicles, 1955 Bel Air (’55 Revive), 1970 Camaro, and 1968 Camaro convertible went along for the drive - over 4000 miles to Tennessee and back to California for the ultimate road trip!
THE CPP STORYThe early days were not glamorous for CPP. The Ries family was growing, and space in their initial company headquarters (the garage) was shrinking. Big decisions had to be made on the future of Classic Performance. In September of 1993, the lease was signed on a new storefront, complete with 300 sq. ft. show-room, sales office and warehouse in Buena Park, California. A new build department was added along with shipping and storage shelves. Finding success with the classic truck industry, and more room to grow, CPP expanded its product line to include classic car market, once again providing the same top quality products. CPP also added a full line of all the top brands in the industry: Brembo, RideTech, Lokar, Ididit, Total Cost Involved, Heidt's, Unisteer, Wilwood, Baer Brakes, and many more. CPP's engineers work closely with these companies when developing new prod-ucts, having found that partnering together compliments each other's parts and ultimately benefitting the end user.
In May of 2005, CPP once again moved buildings to Anaheim, California. With an additional 10,000 sq. ft. added in 2008 and 2011, CPP was occupying over 40,000 sq. ft., including a beautiful 3,000 sq. ft. showroom, plus sales and business offices and ship-ping and receiving departments. This also allowed us to expand our manufacturing facilities including four milling centers and three lathes centers, R&D department, and graphics and mar-keting department. At the end of 2012, CPP once again grew, purchasing our own 80,000 sq. ft. building in Placentia, California. This enormous undertaking doubled our office, showroom, ship-ping and manufacturing space. This has enabled us to house our entire operation under one roof and more effectively and effi-ciently get parts to our customers.
As we move forward into our 24th year of business, we have not forgotten where it all began....building quality parts at an afford-able price for our customers.
Who could've guessed what was going to become of a little Southern California parts shop called Classic Performance Products, Inc. back in December 1991. 24 years later, CPP has become the industry's "go to" specialist in steering, brakes and suspension products for classic cars and trucks.
With the support of his wife, Jill, Jim Ries opened for business in December of 1991 and has not looked back since. Ries grew up watching his dad, Jack "JR" Ries, run a successful classic truck parts business in the '60s and '70s, but wasn't ready to open shop until he had a few of his own real world experiences. When the monster truck craze hit Southern California, Ries got in on the action at the very beginning. Building and racing several of these massive vehicles for Horse Power Promotions gave him valuable knowledge on the inner workings of steering, brakes and suspen-sion truck parts.
Moving from monster trucks to classic trucks, Ries worked for Seth Doulton at Golden State Pickup Parts for several years before venturing out on his own. Not satisfied to just sell parts, Ries set out to redefine the classic truck steering, brakes and suspension industry with better quality and better cost products. Based on the early success of the first manufacturered products, the engine and transmission crossmembers, CPP went on to design Brake Booster Kits, C10 Lowering Kits and Suspension Kits, "Bolt On" Disc Brake Kits, and the list goes on.
In recent years, the development of CPP's Mini™ Sub-Frame Suspension Kits, Totally Tubular™ Control Arms, 500 Series™ Power Steering Boxes, Modular™ Spindles, SOS™ Brake Kits, and the award-winning MCPV1™ Master Cylinder has put Classic Performance Products, Inc. on the map. Working with the indus-try's top magazine editors at Super Chevy, Classic Trucks, Custom Classic Trucks, Hot Rod, Street Rodder, Rod & Custom, Drive!, and many more have provided us many opportunites to test our newly developed parts on vehicles for our customers to read about.
CPP's first storefront located in Buena Park, circa 1995
Our friendly sales team.
In the early days, CPP's first showroom and front counter.
Our new Placentia showroom displays thousands of our products.
The new CPP Tech Center allows us to test new prod-ucts on vehicles to ensure
quality and fit.
Toll Free: (800) 522-5004 • www.classicperform.com2
Ship To:Name
Address
City State Zip
(Evening)
Bill To:Name
Address
City State Zip
Phone (Daytime)
Email address (important for ship verification):
ORDER FORM
Vehicle Information:Year: ____________________________ Make: _________________________Model: _________________________________________________________1955-57 Chevy Car Radiator Position ❑ V-8 ❑ 6 cyl.
Additional info:
Engine and Transmission Information:Year: ____________________________ Make: _________________________❑ 6 cyl. ❑ Small Block V-8 ❑ Big Block V-8C.I. __________________ Trans Type.____________________________Rear Axle: ______________________________________________________Front Suspension ___________________ Rear Suspension _________________Front Brakes_______________________ Rear Brakes ____________________
QUANTITY PART # DESCRIPTION
SUB TOTALSHIPPING & HANDLING
CALIFORNIA RESIDENTS ADD 8% TAXTOTAL
PRICE EACH TOTAL
Terms: All prepaid orders by check or money order that do not include freight charges will be held until freight is collected. Freight charges will be added to your total on all credit card orders.
Return Policy: Customer must call for a return (RMA) number on all returns, regardless of the reason for the return. All returns must be accompanied by a copy of the original invoice. No returns accepted after 30 days. No returns on special orders, electrical parts, installed or altered parts. All returned merchandise is subject to inspection before a replacement or refund is issued. A 20% restocking fee applies to correctly shipped items that are returned within 30 days. Restocking fee will be waived if return is accompanied by a new order with a value of $25.00 more than the returned order. NO EXCEPTIONS!
Shipping Services: ❑ Residential ❑ Business❑ Regular Ground ❑ 3-Day Select* ❑ 2-Day Air*❑ Next Day Air* ❑ Saturday Delivery**Available for an Additional Charge
Payment Method: ❑ Credit Card* ❑ Certified Check*❑ Personal Check* ❑ Money Order**Pre-paid orders by Credit card and Certified Check will be shipped as soon as possible. Personal checks and Money Orders will be held 10-20 days pending check clearance before shipping.
❑ Visa❑ Mastercard❑ Discover
Name on Card ___________________________________________________________________________________________Card # ___________________________________________________ Expiration ______________________________________Billing Address ___________________________________________________________________________________________Authorized Signature _______________________________________________________________________________________
DATE: __________________________________
800-522-5004 • 714-522-2000 • FAX: 714-522-2500 • www.classicperform.com
(CALL FOR QUOTE)
ORDERING INFORMATION Phone orders – Call us at 1-800-522-5004. Our sales staff is available Monday to Friday, 8 am to 5 pm and Saturday, 8 am to 12 pm. Please have the part numbers available in order to save time. If you are unsure, our helpful sales staff will be able to verify the part numbers for you.
Fax orders – Our fax line is available 24 hours a day. Send all order forms to (714) 522-2500. Please make sure to include a contact phone number and email address for confirmation.
Mail orders – Send the order form found on page 283 along with your payment to: Classic Performance Products, Inc. 378 E. Orangethorpe Ave., Placentia CA 92870. Please call us for a shipping estimate prior to sending your order.
Online orders – Visit our website at www.classicperform.com. You can find the parts you need and add them to the cart. For your protection, all orders submitted thru the website are subjected to a thorough verifica-tion procedure prior to shipping. We will be emailing you with a confirma-tion.
FIRST TIME ORDERSAll first time customers paying by credit card must have their first order shipped to the billing address of the credit card. Future orders may be shipped to a separate address 60 days after receipt of the first order, pro-vided the first shipment has been received at the billing address uncon-tested. Customers can also use the toll-free number on the back of their card to contact the credit card company and add an “Alternative Shipping Address” authorizing purchase be delivered to a destination other than your billing address.
SALES TAX California residents must include 8% State Sales Tax. If you are an automo-tive parts business and/or you have a tax number, please include it on a tax card with your order.
SPECIAL / CUSTOM PRODUCTS A 50% non refundable deposit is required before any Custom Orders or Special Products are manufactured by CPP. Allow 4 to 6 weeks for deliv-ery. No returns or refunds are allowed on special/ custom orders.
BACK ORDERS Listings in the catalog do not imply availability. If some items are out of
stock when you place your order, we encourage that you request we ship ahead your other items. We will keep you updated on the availability of your part so always include your email address. We will ship as soon as possible when the part comes in.
PAYMENT We accept Visa, MasterCard and Discover credit cards, money orders, wire bank transfer, personal and company checks. We verify all credit card orders for your protection. In some cases, this may cause a slight delay in shipping. We also accept Paypal upon request. Please call for a money request and a reference number if using Paypal. For Paypal payments, we only ship to confirmed addresses. Orders paid by credit card or certified funds will be processed immediately, checks or money orders may be held 10-20 business days pending check clearance before shipping. There will be a $25 service charge on any returned checks. Stop payment will con-stitute legal action and/or collection. Sorry, we do not accept COD orders. We charge the full amount of the order at the time of shipping.
SHIPPING A shipping and handling fee is added to all orders shipped. The shipping charge is determined at the time of shipment. The standard fee is Published Rate + Handling Fee. For example, $10 (published rate) + $1.50 (handling fee) = $11.50 total shipping charge. Oversized items and certain destina-tions (AK, HI, PR, International) will be higher. Express shipping is avail-able at an extra cost. Please contact us if you require a shipping quote.
We ship via Fedex, UPS, and truck freight for palletized orders. Small parts may be shipped via USPS.
International orders are shipped via Fedex, DHL or DB Schenker. We only ship via Air Freight. These orders may incur duties, customs broker fees and other charges relate to the importation of the merchandise. All charges are sole responsibility of the customer. Please check with your local cus-toms office for more information.
SHIP NOTIFICATIONPlease provide your email address and we will send you a shipping notifi-cation notice with your tracking number.
TECHNICAL SUPPORT Steering, suspension and braking systems and components require proper installation procedures to assure safe and correct operation. Always test completed installation in a safe area prior to placing the vehicle in ser-vice. CPP’s technical service personnel, including a licensed professional engineer, have the training and experience necessary to assist you with installation or operation problems. Also, they will be happy to speak with your installation mechanic, if you have one. PLEASE REFER TO OUR COMPLETE TECHNICAL AND INSTRUCTION GUIDES ON OUR WEB SITE. Also note: We do not reimburse for any labor charges if you contract for professional installation.
POLICIES & PROCEDURES
www.classicperform.com toll free 800.522.5004
Feeling Social?
Reach Us At:
Phone Line:(714) 522-2000
Fax Line:(714) 522-2500
Email:[email protected]
Mailing Address:378 E. Orangethorpe Avenue
Placentia, CA 92870
WE ARE HERE TO HELP!
Check out our blog @http://classicperformanceproducts.blogspot.com/
24 Hours a Day... 7 Days a Week!TECH GUIDES
INSTRUCTION SHEETSMAGAZINE STORIES
ETC.!
Classic Performance Products, Inc. 714.522.2000 | fax 714.522.2500 378 E. Orangethorpe Ave. | Placentia, CA 92870 | www.classicperform.com
Steering, Brake & Suspension Specialists
Rev. 4/9/2013
#7081PTSBK & #7081PTSBK-U Instructionsfor 1970-81 Rear Pro-Touring Sway Bar
Instructions:1. Coat the sway bar pivot bushing with the supplied grease.
2. Install the pivot bushings onto the sway bar. Refer to the illustration below as needed.
3. Position the sway bar mounting brackets around the bushings.
4. Assemble the axle portion of the sway bar mount around the axle and loosely attach the sway bar to the rear axle. The dip in the sway bar will be down and toward the rear.
5. Position the end link mounts on the bottom of the chassis. The mounts will be on the flat portion of the chassis above the sway bar end, and a little wider than the sway bar. Locate the mounts flush to the end of the slot on the bottom of the chassis. (The nut tab will be inserted through this slot).
6. Using the mounts as a guide drill 3/8” holes into the bottom portion of the chassis.
7. Insert the nut tabs through the slot and into the chassis. Using the 3/8” hardware, bolt the mounting flanges to the chassis.
8. Assemble the end links. Thread the thin nuts onto each of the male rod ends, then the thread the female rod ends onto the male rod ends.
9. Using the 7/16” hardware and spacer bolt the end link assemblies to the sway bar and mounting brackets.
10. Tighten the thin nuts against the female rod ends.
11. Tighten the axle clamps and sway bar pivot mounts to the axle.
12. Be sure to road test the car so you can familiarize yourself with the cars’s new handling characteristics.
1/4″ grade 5 10lb/ft 1/4″ grade 8 14lb/ft5/16″ grade 5 19lb/ft 5/16″ grade 8 29lb/ft3/8″ grade 5 33lb/ft 3/8″ grade 8 47lb/ft7/16″ grade 5 54lb/ft 7/16″ grade 8 78lb/ft1/2″ grade 5 78lb/ft 1/2″ grade 8 119lb/ft9/16″ grade 5 114lb/ft 9/16″ grade 8 169lb/ft5/8″ grade 5 154lb/ft 5/8″ grade 8 230lb/ft
GENERAL TORQUE SPECIFICATIONS:
© Classic Performance Products, Inc. 2013All rights reserved. This document may not be reproduced without prior written permission of CPP.
www.classicperform.com@VISIT OUR WEBSITE:
How Are We Doing?
As we are always striving to make your experience with CPP better, we would love to hear how we are doing. Send in your comments...if you have had a great experience, bad one, or just mediocre...please let us know.
Please mail to:Classic Performance Products, Inc.
Attn: CPP Feedback378 E. Orangethorpe Avenue
Placentia, CA 92870
Or e-mail: [email protected](use “Feedback” in the subject line)
Order by Phone...Pick up at Will Call
Do you live in our area or planning a trip
to come visit? Save yourself some time
in line and place your parts order over the
telephone. Be sure to tell your salesman that you will be coming to pick it up and we will have your ordering waiting for you at
Will Call. Save time and money on shipping costs!
SHOWROOM HOURS:Monday - Friday 8:00am - 5:00pm
Saturday 8:00am - 1:30pm
Note: Due to the variances in the manufacture of after-market products and/or original equipment, production run changes, multiple suppliers of the same product(s) and almost limitless options for such parts, it is the ultimate responsibility of you (the buyer/consumer) to confirm in advance that such part(s) will fit your vehicle.
DAMAGE OR SHORTAGESMake certain you inspect all packages in the presence of the driver/carrier. If you receive a package that has been damaged or opened, make a claim with the driver/carrier at that time. All claims of loss, concealed damaged, damage or other destruction must be made by you with the carrier. Save all boxes and packing materials, as the carrier may want to inspect it. We apologize for this inconvenience - but this is our carrier’s shipping policy. Any shortages not the fault of the carrier must be reported within 5 days of receiving order. No exceptions allowed.
RETURNS Merchandise may be returned or exchanged within the first 30 days of purchase. We do not take returns or exchanges after 30 days. How to return a Product:
1. Customer must request a Return Merchandise Authorization number (RMA) by contacting us via phone or online at www.classicperform.com/returns
2. Return part in the original box and packaging with the RMA number marked on the box.
3. Include a written explanation of the reason for return and copy of the original receipt.
4. Customer is responsible for all shipping costs, regardless of the carrier. We strongly suggest you use UPS, Fedex or USPS with tracking number and insurance to protect yourself against loss or damages.
All returns are subject to inspection before a replacement or credit is issued. We do not issue cash refunds. A 20% restocking fee may be applied, unless a new order is placed with a value of $25 more than the returned order or by choosing store credit. Parts that have been installed, painted, abused or modified will not be accepted for return and may be sent back to the customer. Electrical and special ordered parts are non-refundable.
WARRANTYAll CPP products are guaranteed for life from date of purchase, to be free of defects in materials and workmanship. This guarantee is void in the event of misuse, neglect, improper installation or misdiagnosis. At our option, we will repair or replace any product found to be defective subject to our inspection and approval. Warranty returns require the same procedures as above. All sus-pected defective item must be authorized prior to return; they must have a Return Merchandise Authorization (RMA) number, the original invoice, a brief description of the problem (“defec-tive” is not sufficient) and customer must prepay shipping. Parts that are disassembled, altered, modified, disfigured, or abused will not be covered by our warranty. This warranty does not cover reimbursement of labor costs or incidental damages (if any). There
are no refunds on shipping costs, electrical parts, or special order merchandise.
PRODUCT CHANGESWe are constantly updating and revising our products to bring you the best quality parts available. CPP reserves the right to make changes and improvements without notification. We have no liabil-ity to update previously sold items.
CORE CHARGES/DEPOSITS The purpose of a core deposit / charge is to insure the return of rebuildable parts. Your deposit will be promptly refunded when we receive your complete, rebuildable core. A copy of your original purchase invoice must accompany your core. No refund will be issued for broken, damaged, disassembled or incomplete cores. No exceptions will be allowed. All cores must be prepaid by customer and returned within 30 days of purchase to obtain full core value. Cores not returned within 30 days will receive only one half (1/2) of core value. Unless cores are returned within a timely fashion, other customers will have to wait.
LIABILITY The seller, CPP, hereby expressly disclaims all warranties, either expressed or implied warranty or merchant ability of fitness for a purpose, and CPP neither assumes nor authorizes any other person to assume for it any liability in connection with the sale of this mer-chandise. CPP will be responsible only for “the products sold by us.” Sellers and manufacturers only obligation shall be to replace such quantity of the product proved to be defective by CPP. Neither seller nor manufacturer shall be liable for any loss, injury or dam-age, direct or consequential, arising out of the use of, or the inabil-ity of product. After use, the user shall assume all risk and liability whatsoever in connection thereof. For out of country, it is the responsibility of the consumer to research the requirement of their local authorities and how local policies may apply to the use of our products prior to purchase and installation.
PRICING, TERMS, CONDITIONS CPP reserves the right to change prices, terms, specifications and other information without notice. Please call or write us if you have any questions or you feel there is a discrepancy.
NOTICE: © Copyright Classic Performance Products, Inc. 2015. All Rights Reserved. This publication, in whole or in part, may not be reproduced, stored in a computerized, or other retrieval system or transmitted in any form, or by any means whatsoever without the prior written permission of Classic Performance Products, Inc.
Steering | Brakes | Suspension Toll Free: (800) 522-5004 • www.classicperform.com
378 E. Orangethorpe AvenuePlacentia, CA • 92870
PRESORTED
BOUND PRINTED MATTER
U.S. POSTAGE
PAIDBUENA PARK, CA
PERMIT NO. 88
CLASSIC PERFORMANCE PRODUCTS, Inc.
$5.00
PRODUCT CATALOG
CLASSICPERFORM.COM | 800.522.5004
• CHEVY TRUCK • CHEVY TRI-FIVE & FULLSIZE • CAMARO • NOVA • CHEVELLE • EL CAMINO • • FORD CAR & TRUCK • G-BODY • CADILLAC • LINCOLN • MOPAR •
CLASSICPERFORM.COM | 800.522.5004
CLASSIC PERFORMANCE PRODUCTS, INC.
CLASSIC PERFORMANCE PRODUCTS, INC.
CLA
SSIC
PER
FOR
MA
NC
E P
RO
DU
CTS
, INC
.
PR
OD
UC
T CATA
LOG
#21
#21CATALOG
378 E. ORANGETHORPE AVENUE PLACENTIA, CA 92870 •