clark-drain products - trinidad and tobago · clark-drain limited station road yaxley peterborough...
TRANSCRIPT
Municipal Castings
Clark-Drain LimitedStation RoadYaxleyPeterborough PE7 3EQ
Telephone: 01733 765317Fax: 01733 246923
Email: [email protected]: www.clark-drain.com
Due to our continual development program we reserve the right to upgrade products without prior notice.Products must be fitted in accordance with Clark-Drain installation guides.
LMRTdesign.com 0054 0711
CLARK-DRAIN PRODUCTS
Galvanised Pressed Steel Covers
Recessed Pavior Range
Internal Recessed Range
Municipal Covers and Frames
Polypropylene Inspection Covers and Frames
Technical Channel
Domestic Channel
One call has it covered!
Your local stockist
40 OverOver
| CONTENTS | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
CONTeNTS INTRODUCTION
www.clark-drain.com | [email protected] | iNTrODuCTiON | 1 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Introduction, Installation and Loadings 1
High Max F900 Double-Tri Covers and Frames 2
High Max e600 and D400 Double-Tri Covers and Frames 3
Circular D400 Covers and Frames 4
D400 Double-Tri Covers and Frames 5–6
D400 Double-Tri Covers and Frames 7
C250 Solid Top Covers and Frames 8
B125 Solid Top Covers and Frames 9
B125 Solid Top Covers and Steel Frames 10
A15 Solid Top Covers and Frames 11
D400 Double-Tri Gully Gratings 12
D400 Hinged Gully Gratings 13
C250 Hinged Gully Gratings 14
Surface Boxes 15
Ancillary Products and Step Irons 16
Manhole Lifters and Lifting Keys 17
INSTALLATION AND LOADINGSThe appropriate class of manhole cover or gully grate required depends on the place of installation.
The various places of installation have been divided into groups numbered 1 to 6.
The diagram (right) shows the location of some of these groups in a highway environment.
A guide as to which class of manhole top or gully top should be used is shown in parenthesis for each group.
The selection of the appropriate class is the responsibility of the designer. Where there is any doubt the stronger class should be selected.
GROUP 1 (min Class A15)
Areas which can only be used by pedestrians and pedal cyclists.
GROUP 2 (min Class B125)
Footways, pedestrian areas and comparable areas, car parks or car parking decks.
GROUP 3 (min Class C250)
For gully tops installed in the area of kerbside channels of roads (see diagram above) which when measured from the kerb edge extend a maximum of 0.5m into the carriageway and a maximum of 0.2m into the footway.
GROUP 4 (min Class D400)
Carriageway of roads (including pedestrian streets), hard shoulders (see diagram above) and parking areas for all types of road vehicles.
GROUP 5 (min Class E600)
Areas imposing high wheel loads eg. docks and aircraft pavements.
GROUP 6 (min Class F900)
Areas imposing particularly high wheel loads eg. aircraft pavements.
Clark-Drain Ltd, a leading supplier of drainage products with over 40 years experience within the construction engineering sector, are proud to offer our latest catalogue of Municipal Castings.
At Clark-Drain we not only offer high quality products, linked to innovative design, but also the highest level of customer service, utilising our own large fleet of delivery vehicles and carefully selected logistics providers.
QuALITY | RELIABIL ITY | InnovATIon
| CONTENTS | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
CONTeNTS INTRODUCTION
www.clark-drain.com | [email protected] | iNTrODuCTiON | 1 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
1
2
3
4
5–6
7
8
9
10
11
12
13
14
15
16
17
INSTALLATION AND LOADINGSThe appropriate class of manhole cover or gully grate required depends on the place of installation.
The various places of installation have been divided into groups numbered 1 to 6.
The diagram (right) shows the location of some of these groups in a highway environment.
A guide as to which class of manhole top or gully top should be used is shown in parenthesis for each group.
The selection of the appropriate class is the responsibility of the designer. Where there is any doubt the stronger class should be selected.
of some of these groups
top should
GROUP 1 (min Class A15)
Areas which can only be used by pedestrians and pedal cyclists.
GROUP 2 (min Class B125)
Footways, pedestrian areas and comparable areas, car parks or car parking decks.
GROUP 3 (min Class C250)
For gully tops installed in the area of kerbside channels of roads (see diagram above) which when measured from the kerb edge extend a maximum of 0.5m into the carriageway and a maximum of 0.2m into the footway.
GROUP 4 (min Class D400)
Carriageway of roads (including pedestrian streets), hard shoulders (see diagram above) and parking areas for all types of road vehicles.
GROUP 5 (min Class E600)
Areas imposing high wheel loads eg. docks and aircraft pavements.
GROUP 6 (min Class F900)
Areas imposing particularly high wheel loads eg. aircraft pavements.
INSTALLATION AND LOADINGS
Clark-Drain Ltd, a leading supplier of drainage products with over 40 years experience within the construction engineering sector, are proud to offer our latest catalogue of Municipal Castings.
At Clark-Drain we not only offer high quality products, linked to innovative design, but also the highest level of customer service, utilising our own large fleet of delivery vehicles and carefully selected logistics providers.
QuALITY | RELIABIL ITY | InnovATIon
| 2 | high max DOubLE Tri | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
HIGH MAx DOUBLe TRI
All products feature several new innovative designs to ensure long-lasting performance in areas subject to
high-density road-vehicle traffic.
All of the High Max products are designed to be compliant to uK Highways Agency ‘Design Manual for
Roads and Bridges’ (HA104/02/09).
If your application is in an area of high risk and/or subject to high-density traffic, the Clark-Drain High Max
product range is for you!
Extra-strength frame with over-sized wall sections to increase durability. Profiled corners to interlock with
frame and minimize movement and noise. Inboard cover supports to minimize risk of failure even under
the toughest of conditions. Extra large flange to minimize load and stress transmission to bedding area.
Designed to comfortably exceed load requirements of BS En124 Class D400. Polished Skid Resistance
value1 (PSRv) = Exceeds 60, Kitemark Certified to BS En124:1994.
1using pendulum test method with 4S block.
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 801AH KMF* F900 600 x 600 813 x 813 150
CLKS 802AH KMF* F900 675 x 675 875 x 875 150
CLKS 807AH KMF* F900 750 x 750 1013 x 1013 150
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
BS En 124 F900
En 124
F900(90T)
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 F900 Products marked ‘*’ are HA104/02 and HA104/09 (low and high-risk
areas) compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
Picture shows the CLKS 801AH KMF
HIGH MAx DOUBLe TRI
www.clark-drain.com | [email protected] | high max DOubLE-Tri | 3 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 801AH KME* E600 600 x 600 813 x 813 150
CLKS 802AH KME* E600 675 x 675 875 x 875 150
CLKS 808AH KME* E600 1200 x 675 1365 x 835 150
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 E600 and D400 Products marked ‘*’ are HA104/02 and HA104/09 (low and high-risk
areas) compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
BS En 124 Class E600 and D400
Suitable for highways
En 124
e600(60T)
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 801H KMD* D400 600 x 600 738 x 738 100
CLKS 801AH KMD* D400 600 x 600 765 x 765 150
CLKS 802H KMD* D400 675 x 675 802 x 802 100
CLKS 802AH KMD* D400 675 x 675 828 x 828 150
CLKS 807AH KMD* D400 750 x 750 900 x 900 150
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
Suitable for highways
Picture shows the CLKS 801H KMD
En 124
D400(40T)
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) High Max Ductile Iron manhole cover and frame BS En 124 Class E600 and D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) High Max Ductile Iron manhole cover and frame BS En 124 Class F900, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
Suitable for highways
| 2 | high max DOubLE Tri | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
HIGH MAx DOUBLe TRI
All products feature several new innovative designs to ensure long-lasting performance in areas subject to
high-density road-vehicle traffic.
All of the High Max products are designed to be compliant to uK Highways Agency ‘Design Manual for
Roads and Bridges’ (HA104/02/09).
If your application is in an area of high risk and/or subject to high-density traffic, the Clark-Drain High Max
product range is for you!
Extra-strength frame with over-sized wall sections to increase durability. Profiled corners to interlock with
frame and minimize movement and noise. Inboard cover supports to minimize risk of failure even under
the toughest of conditions. Extra large flange to minimize load and stress transmission to bedding area.
Designed to comfortably exceed load requirements of BS En124 Class D400. Polished Skid Resistance
value1 (PSRv) = Exceeds 60, Kitemark Certified to BS En124:1994.
1using pendulum test method with 4S block.
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 801AH KMF* F900 600 x 600 813 x 813 150
CLKS 802AH KMF* F900 675 x 675 875 x 875 150
CLKS 807AH KMF* F900 750 x 750 1013 x 1013 150
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
BS En 124 F900
En 124
F900(90T)
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 F900 Products marked ‘*’ are HA104/02 and HA104/09 (low and high-risk
areas) compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
Picture shows the CLKS 801AH KMF
HIGH MAx DOUBLe TRI
www.clark-drain.com | [email protected] | high max DOubLE-Tri | 3 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 801AH KME* E600 600 x 600 813 x 813 150
CLKS 802AH KME* E600 675 x 675 875 x 875 150
CLKS 808AH KME* E600 1200 x 675 1365 x 835 150
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 E600 and D400 Products marked ‘*’ are HA104/02 and HA104/09 (low and high-risk
areas) compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
BS En 124 Class E600 and D400
Suitable for highways
En 124
e600(60T)
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 801H KMD* D400 600 x 600 738 x 738 100
CLKS 801AH KMD* D400 600 x 600 765 x 765 150
CLKS 802H KMD* D400 675 x 675 802 x 802 100
CLKS 802AH KMD* D400 675 x 675 828 x 828 150
CLKS 807AH KMD* D400 750 x 750 900 x 900 150
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
Suitable for highways
Picture shows the CLKS 801H KMD
En 124
D400(40T)
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) High Max Ductile Iron manhole cover and frame BS En 124 Class E600 and D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) High Max Ductile Iron manhole cover and frame BS En 124 Class F900, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
Suitable for highways
| 4 | CirCuLar D400 | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Closed Keyways Black Bitumen Coated Skeleton flange
BS En 124 Class D400
Picture shows the CLKS 704 H&LRKMD Picture shows the CLKS 704 KMD
En 124
D400(40T)
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 704 KMD D400 600 diameter 750 x 750 100
CLKS 704 H&LRKMD D400 600 diameter 820 diameter 100
CLKS 704 H&LSKMD D400 600 diameter 825 x 825 100
Optional extras: Badging (eg. FW and SW), Locking, Safety grids, Security plates, ventilated.
Picture shows the CLKS 704 H&LRKMD
CIRCULAR D400
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 693H KMD* D400 1200 x 675 1333 x 809 100
CLKS 693AH KMD* D400 1200 x 675 1344 x 820 150
CLKS 694AH KMD* D400 1800 x 675 1950 x 825 150
CLKS 695H KMD* D400 1500 x 750 1633 x 898 100
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Products marked ‘*’ are HA104/02 and HA104/09 (low-risk areas)
compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
BS En 124 Class D400
Suitable for highways
www.clark-drain.com | [email protected] | DOubLE-Tri | 5 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
En 124
D400(40T)
DOUBLe-TRI
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
Picture shows the CLKS 693AH KMD
| 4 | CirCuLar D400 | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Closed Keyways Black Bitumen Coated Skeleton flange
BS En 124 Class D400
Picture shows the CLKS 704 H&LRKMD Picture shows the CLKS 704 KMD
En 124
D400(40T)
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 704 KMD D400 600 diameter 750 x 750 100
CLKS 704 H&LRKMD D400 600 diameter 820 diameter 100
CLKS 704 H&LSKMD D400 600 diameter 825 x 825 100
Optional extras: Badging (eg. FW and SW), Locking, Safety grids, Security plates, ventilated.
CIRCULAR D400
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 693H KMD* D400 1200 x 675 1333 x 809 100
CLKS 693AH KMD* D400 1200 x 675 1344 x 820 150
CLKS 694AH KMD* D400 1800 x 675 1950 x 825 150
CLKS 695H KMD* D400 1500 x 750 1633 x 898 100
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Products marked ‘*’ are HA104/02 and HA104/09 (low-risk areas)
compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
BS En 124 Class D400
Suitable for highways
www.clark-drain.com | [email protected] | DOubLE-Tri | 5 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
3 Point Suspension
En 124
D400(40T)
DOUBLe-TRI
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
Picture shows the CLKS 693AH KMD
TeL: 01733 765316FAX: 01733 246920
| 2 | CONTENTS | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
CONTeNTS
| 6 | DOubLE-Tri | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
BS En 124 Class D400
Suitable for highways Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 701H KMD* D400 600 x 600 739 x 739 100
CLKS 701AH KMD* D400 600 x 600 752 x 752 150
CLKS 1659H KMD* D400 675 x 675 802 x 802 100
CLKS 1659AH KMD* D400 675 x 675 815 x 815 150
CLKS 750HS KMD* D400 750 x 600 915 x 765 100
CLKS 750AHS KMD* D400 750 x 600 900 x 750 150
CLKS 753H KMD* D400 750 x 750 904 x 904 100
CLKS 753AH KMD* D400 750 x 750 915 x 915 150
CLKS 751H KMD* D400 900 x 900 1054 x 754 100
Optional extras: Badging (eg. FW and SW), Locking, Safety grids, Security plates, ventilated.
Picture shows the CLKS 701H KMD
En 124
D400(40T)
En 124
D400(40T)
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Products marked ‘*’ are HA104/02 and HA104/09 (low-risk areas)
compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
DOUBLe-TRI
www.clark-drain.com | [email protected] | DOubLE-Tri | 7 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
BS En 124 Class D400
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 770 KMD D400 300 x 300 450 x 450 100
CLKS 755 KMD D400 450 x 450 550 x 550 100
CLKS 756 KMD D400 600 x 450 737 x 587 100
CLKS 701 KMD D400 600 x 600 695 x 695 100
CLKS 701A KMD D400 600 x 600 760 x 760 150
CLKS 1659 KMD D400 675 x 675 827 x 827 100
CLKS 1659A KMD D400 675 x 675 835 x 835 150
CLKS 752 KMD D400 900 x 600 1050 x 750 100
CLKS 752A KMD D400 900 x 600 1065 x 765 150
Optional extras: Badging (eg. FW and SW), Locking, Safety grids, Security plates, ventilated.
Picture shows the CLKS 1659 KMD
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Skeleton flange
DOUBLe-TRI
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
Products marked ‘*’ are HA104/02
TeL: 01733 765316FAX: 01733 246920
| 2 | CONTENTS | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
CONTeNTS
| 6 | DOubLE-Tri | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
BS En 124 Class D400
Suitable for highways Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 701H KMD* D400 600 x 600 739 x 739 100
CLKS 701AH KMD* D400 600 x 600 752 x 752 150
CLKS 1659H KMD* D400 675 x 675 802 x 802 100
CLKS 1659AH KMD* D400 675 x 675 815 x 815 150
CLKS 750HS KMD* D400 750 x 600 915 x 765 100
CLKS 750AHS KMD* D400 750 x 600 900 x 750 150
CLKS 753H KMD* D400 750 x 750 904 x 904 100
CLKS 753AH KMD* D400 750 x 750 915 x 915 150
CLKS 751H KMD* D400 900 x 900 1054 x 754 100
Optional extras: Badging (eg. FW and SW), Locking, Safety grids, Security plates, ventilated.
Picture shows the CLKS 701H KMD
En 124
D400(40T)
En 124
D400(40T)
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Products marked ‘*’ are HA104/02 and HA104/09 (low-risk areas)
compliant Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Solid flange
DOUBLe-TRI
www.clark-drain.com | [email protected] | DOubLE-Tri | 7 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
BS En 124 Class D400
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 770 KMD D400 300 x 300 450 x 450 100
CLKS 755 KMD D400 450 x 450 550 x 550 100
CLKS 756 KMD D400 600 x 450 737 x 587 100
CLKS 701 KMD D400 600 x 600 695 x 695 100
CLKS 701A KMD D400 600 x 600 760 x 760 150
CLKS 1659 KMD D400 675 x 675 827 x 827 100
CLKS 1659A KMD D400 675 x 675 835 x 835 150
CLKS 752 KMD D400 900 x 600 1050 x 750 100
CLKS 752A KMD D400 900 x 600 1065 x 765 150
Optional extras: Badging (eg. FW and SW), Locking, Safety grids, Security plates, ventilated.
Picture shows the CLKS 1659 KMD
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 D400 Closed Keyways Black Bitumen Coated non-Rock 3 Point Suspension Skeleton flange
DOUBLe-TRI
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Ductile Iron manhole cover and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 C250 Closed Keyways Black Bitumen Coated one piece Solid Top
BS En 124 Class C250
| 8 | SOLiD TOP | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Picture shows the CLKS 708 KMC
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 778 KMC C250 600 x 600 760 x 760 75
CLKS 706 KMC C250 750 x 600 871 x 721 75
CLKS 707 KMC C250 750 x 750 872 x 872 75
CLKS 708 KMC C250 900 x 600 1020 x 721 75
CLKS 709 KMC C250 900 x 900 1050 x 1050 75
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
En 124
C250(25T)
SOLID TOP
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and frame to BS En 124 Class C250, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
www.clark-drain.com | [email protected] | SOLiD-TOP | 9 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
SPeCIFICATIONS Ductile Iron Cover and Frame Closed Keyways Black Bitumen Coated one piece Solid Top
BS En 124 Class B125
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 1657 EnB B125 450 dia 550 dia 40
CLKS 761 EnB B125 450 x 450 524 x 524 40
CLKS 762 EnB B125 600 x 450 675 x 525 40
CLKS 779 EnB B125 600 x 450 710 x 570 75
CLKS 759 EnB B125 600 dia 720 x 720 40
CLKS 777 EnB B125 600 x 600 675 x 675 40
CLKS 778 EnB B125 600 x 600 700 x 700 75
CLKS 780 EnB B125 675 x 675 775 x 775 40
CLKS 722 EnB B125 750 x 600 850 x 700 40
CLKS 752 EnB B125 900 x 600 990 x 690 45
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
Picture shows the CLKS 777 EnBPicture shows the CLKS 1657 EnB
En 124
B125(12.5T)
SOLID TOP
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and frame to BS En 124 Class B125, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Cover and Frame Kitemarked to BS En 124 C250 Closed Keyways Black Bitumen Coated one piece Solid Top
BS En 124 Class C250
| 8 | SOLiD TOP | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Picture shows the CLKS 708 KMC
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 778 KMC C250 600 x 600 760 x 760 75
CLKS 706 KMC C250 750 x 600 871 x 721 75
CLKS 707 KMC C250 750 x 750 872 x 872 75
CLKS 708 KMC C250 900 x 600 1020 x 721 75
CLKS 709 KMC C250 900 x 900 1050 x 1050 75
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
En 124
C250(25T)
SOLID TOP
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and frame to BS En 124 Class C250, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
www.clark-drain.com | [email protected] | SOLiD-TOP | 9 | Due to our continual development programme, we reserve the right to upgrade products without prior notice.
SPeCIFICATIONS Ductile Iron Cover and Frame Closed Keyways Black Bitumen Coated one piece Solid Top
BS En 124 Class B125
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 1657 EnB B125 450 dia 550 dia 40
CLKS 761 EnB B125 450 x 450 524 x 524 40
CLKS 762 EnB B125 600 x 450 675 x 525 40
CLKS 779 EnB B125 600 x 450 710 x 570 75
CLKS 759 EnB B125 600 dia 720 x 720 40
CLKS 777 EnB B125 600 x 600 675 x 675 40
CLKS 778 EnB B125 600 x 600 700 x 700 75
CLKS 780 EnB B125 675 x 675 775 x 775 40
CLKS 722 EnB B125 750 x 600 850 x 700 40
CLKS 752 EnB B125 900 x 600 990 x 690 45
Optional extras: Badging, Locking, Safety grids, Security plates, ventilated.
Picture shows the CLKS 777 EnBPicture shows the CLKS 1657 EnB
En 124
B125(12.5T)
SOLID TOP
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and frame to BS En 124 Class B125, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Cast Iron Cover and Frame Closed Keyways Black Bitumen Coated one piece Solid Top
Picture shows the CLKS 12
Picture shows the CLKS 62
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 1657* A15 450 dia 546 dia 32
CLKS 62 A15 600 x 450 678 x 528 27
CLKS 12 A15 600 x 600 678 x 678 27
*Plastic frame
En 124
A15(1.5T)
BS En 124 Class B125 BS En 124 Class A15
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CD 762 KMB B125 600 x 450 675 x 525 40
CD 777 KMB B125 600 x 600 675 x 675 40
Optional extras: Badging
Picture shows the CD 762 KMB
Picture shows the CD 777 KMB
En 124
B125(12.5T)
SOLID TOP SOLID TOP
| 10 | SOLiD TOP | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | SOLiD-TOP | 11 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and steel frame to BS En 124 Class B125, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Cast Iron manhole cover and frame to BS En 124 Class A15, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Cover and steel Frame Kitemarked to BS En 124 B125 Closed Keyways Black Bitumen Coated one piece Solid Top Galvanised Steel frame
SPeCIFICATIONS Cast Iron Cover and Frame Closed Keyways Black Bitumen Coated one piece Solid Top
Picture shows the CLKS 12
Picture shows the CLKS 62
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CLKS 1657* A15 450 dia 546 dia 32
CLKS 62 A15 600 x 450 678 x 528 27
CLKS 12 A15 600 x 600 678 x 678 27
*Plastic frame
En 124
A15(1.5T)
BS En 124 Class B125 BS En 124 Class A15
Product Code bS EN 124 ref Clear opening (mm) Overall Size (mm) Depth (mm)
CD 762 KMB B125 600 x 450 675 x 525 40
CD 777 KMB B125 600 x 600 675 x 675 40
Optional extras: Badging
Picture shows the CD 762 KMB
Picture shows the CD 777 KMB
En 124
B125(12.5T)
SOLID TOP SOLID TOP
| 10 | SOLiD TOP | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | SOLiD-TOP | 11 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron manhole cover and steel frame to BS En 124 Class B125, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Cast Iron manhole cover and frame to BS En 124 Class A15, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Cover and steel Frame Kitemarked to BS En 124 B125 Closed Keyways Black Bitumen Coated one piece Solid Top Galvanised Steel frame
Product bS EN 124 Clear Overall Waterway Depth Code ref Opening (mm) Size (mm) (cm2) (mm)
CLKS 644 KMD D400 415 x 415 570 x 505 805 100
CLKS 644A KMD D400 415 x 415 570 x 510 805 150
CLKS 502 KMD D400 440 x 400 550 x 527 945 100
CLKS 732 KMD D400 600 x 600 753 x 690 1800 100
CLKS 732HKMD*† D400 600 x 600 750 x 750 2002 100
†Four flanged frame
SPeCIFICATIONS Ductile Iron Gully Grating and Frame Kitemarked to BS En 124 D400 Black Bitumen Coated non-Rock 3 Point Suspension Products marked ‘*’ are HA104/02 and HA104/09 (low-risk areas)
compliant Solid flange on 3 sides
BS En 124 Class D400
Picture shows the CLKS 644 KMD
Picture shows the CLKS 732H KMD
En 124
D400(40T)
DOUBLe-TRI GULLey GRATINGS
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Gulley Grate and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Gully Grating and Frame Kitemarked to BS En 124 Class D400 Black Bitumen Coated Hinged Anti-Theft Captive Hinge non-Rock Wedge Seating Solid flange on 3 sides
BS En 124 Class D400
Product bS EN 124 Clear Overall Waterway Depth Code ref Opening (mm) Size (mm) (cm2) (mm)
CLKS 180 KMD D400 430 x 370 580 x 462 1080 100
CLKS 180 KMDL D400 430 x 370 580 x 462 1080 100
CLKS 180A KMD D400 430 x 370 580 x 467 1080 150
CLKS 231 KMD† D400 430 x 370 580 x 462 660 100
CLKS 185 KMD D400 450 x 450 604 x 542 1300 100
CLKS 179 KMD D400 510 x 360 665 x 458 1095 100
Optional extras: Locking
CLKS 185 KMD - Reversible grate
†Pedestrian area Mesh grating
Picture shows the CLKS 180 KMD
Picture shows the CLKS 231 KMD
En 124
D400(40T)
HINGeD GULLey GRATINGS
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) End Hinged Gulley Grate and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
| 12 | DOubLE-Tri | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | END hiNgED | 13 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Product bS EN 124 Clear Overall Waterway Depth Code ref Opening (mm) Size (mm) (cm2) (mm)
CLKS 644 KMD D400 415 x 415 570 x 505 805 100
CLKS 644A KMD D400 415 x 415 570 x 510 805 150
CLKS 502 KMD D400 440 x 400 550 x 527 945 100
CLKS 732 KMD D400 600 x 600 753 x 690 1800 100
CLKS 732HKMD*† D400 600 x 600 750 x 750 2002 100
†Four flanged frame
SPeCIFICATIONS Ductile Iron Gully Grating and Frame Kitemarked to BS En 124 D400 Black Bitumen Coated non-Rock 3 Point Suspension Products marked ‘*’ are HA104/02 and HA104/09 (low-risk areas)
compliant Solid flange on 3 sides
BS En 124 Class D400
Picture shows the CLKS 644 KMD
Picture shows the CLKS 732H KMD
En 124
D400(40T)
DOUBLe-TRI GULLey GRATINGS
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Double-Tri Gulley Grate and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Gully Grating and Frame Kitemarked to BS En 124 Class D400 Black Bitumen Coated Hinged Anti-Theft Captive Hinge non-Rock Wedge Seating Solid flange on 3 sides
BS En 124 Class D400
Product bS EN 124 Clear Overall Waterway Depth Code ref Opening (mm) Size (mm) (cm2) (mm)
CLKS 180 KMD D400 430 x 370 580 x 462 1080 100
CLKS 180 KMDL D400 430 x 370 580 x 462 1080 100
CLKS 180A KMD D400 430 x 370 580 x 467 1080 150
CLKS 231 KMD† D400 430 x 370 580 x 462 660 100
CLKS 185 KMD D400 450 x 450 604 x 542 1300 100
CLKS 179 KMD D400 510 x 360 665 x 458 1095 100
Optional extras: Locking
CLKS 185 KMD - Reversible grate
†Pedestrian area Mesh grating
Picture shows the CLKS 180 KMD
Picture shows the CLKS 231 KMD
on-Rock Wedge SeatingSolid flange on 3 sides
Picture shows the CLKS 231 KMD
En 124
D400(40T)
HINGeD GULLey GRATINGS
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) End Hinged Gulley Grate and frame to BS En 124 Class D400, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
| 12 | DOubLE-Tri | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | END hiNgED | 13 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Product bS EN 124 Clear Overall Waterway Depth Code ref Opening (mm) Size (mm) (cm2) (mm)
CLKS 128 KMC C250 336 x 380 468 x 580 628 75
CLKS 128 KMCL* C250 336 x 380 468 x 580 628 75
CLKS 232 KMC† C250 336 x 308 486 x 400 457 100
CLKS 129 KMC C250 340 x 305 501 x 403 591 100
CLKS 129 KMCL* C250 340 x 305 501 x 403 591 100
CLKS 131 DL KMC** C250 390 x 315 590 x 520 746 100
CLKS 127 KMC C250 440 x 335 530 x 495 930 75
CLKS 130 KMC C250 440 x 335 535 x 500 935 100
†Pedestrian area Mesh grating. *Locking as standard. **Dished and Locking optional Extras: Locking
SPeCIFICATIONS Ductile Iron Gully Grating and Frame Kitemarked to BS En 124 C250 Black Bitumen Coated End Hinged Anti Theft Captive Hinged Skeleton flange
BS En 124 Class C250
Product bS EN 124 Clear Overall
Skeleton flange
Picture shows the CLKS 129 KMC
Picture shows the CLKS 131 DL KMC
En 124
C250(25T)
HINGeD
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) End Hinged Gulley Grate and frame to BS En 124 Class C250, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Cover and Frame Manufactured to: BS 5834 Part 3 and
BS 750 Black Bitumen Coated Double-Tri and Solid Top Covers Skeleton flange
BS 5834
BS 5834
Part 3
BS
750
Product Code bS 5834 Loading Clear opening (mm) Overall Size (mm) Depth (mm)
Surface Box Double/Tri
CLKS 846 A 100 x 100 200 x 200 100
CLKS 841 A 150 x 150 262 x 262 100
CLKS 845 A 225 x 225 323 x 323 100
CLKS 843 A 300 x 300 408 x 408 100
CLKS 840 A 380 x 230 490 x 340 100
CLKS 840A A 380 x 230 496 x 346 125
CLKS 842 A 430 x 280 530 x 380 100
Surface Box Solid Top
CLKS 847 A 380 x 230 480 x 330 100
CLKS 844 A 300 x 300 400 x 400 75
CLKS 844 FH A 300 x 300 400 x 400 75
Optional extras: Locking, Badging (selected products)
Picture shows the CLKS 847
Picture shows the CLKS 841
SURFACe BOxeS
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron Surface Boxes to BS 5834 Part 3 and BS 750 Grade A, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
| 14 | END hiNgED | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | SurfaCE bOxES | 15 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
Product bS EN 124 Clear Overall Waterway Depth Code ref Opening (mm) Size (mm) (cm2) (mm)
CLKS 128 KMC C250 336 x 380 468 x 580 628 75
CLKS 128 KMCL* C250 336 x 380 468 x 580 628 75
CLKS 232 KMC† C250 336 x 308 486 x 400 457 100
CLKS 129 KMC C250 340 x 305 501 x 403 591 100
CLKS 129 KMCL* C250 340 x 305 501 x 403 591 100
CLKS 131 DL KMC** C250 390 x 315 590 x 520 746 100
CLKS 127 KMC C250 440 x 335 530 x 495 930 75
CLKS 130 KMC C250 440 x 335 535 x 500 935 100
†Pedestrian area Mesh grating. *Locking as standard. **Dished and Locking optional Extras: Locking
SPeCIFICATIONS Ductile Iron Gully Grating and Frame Kitemarked to BS En 124 C250 Black Bitumen Coated End Hinged Anti Theft Captive Hinged Skeleton flange
BS En 124 Class C250
Picture shows the CLKS 129 KMC
Picture shows the CLKS 131 DL KMC
En 124
C250(25T)
HINGeD
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) End Hinged Gulley Grate and frame to BS En 124 Class C250, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
SPeCIFICATIONS Ductile Iron Cover and Frame Manufactured to: BS 5834 Part 3 and
BS 750 Black Bitumen Coated Double-Tri and Solid Top Covers Skeleton flange
BS 5834
BS 5834
Part 3
BS
750
Product Code bS 5834 Loading Clear opening (mm) Overall Size (mm) Depth (mm)
Surface Box Double/Tri
CLKS 846 A 100 x 100 200 x 200 100
CLKS 841 A 150 x 150 262 x 262 100
CLKS 845 A 225 x 225 323 x 323 100
CLKS 843 A 300 x 300 408 x 408 100
CLKS 840 A 380 x 230 490 x 340 100
CLKS 840A A 380 x 230 496 x 346 125
CLKS 842 A 430 x 280 530 x 380 100
Surface Box Solid Top
CLKS 847 A 380 x 230 480 x 330 100
CLKS 844 A 300 x 300 400 x 400 75
CLKS 844 FH A 300 x 300 400 x 400 75
Optional extras: Locking, Badging (selected products)
Picture shows the CLKS 847
Picture shows the CLKS 841
bS 5834 Loading Clear opening (mm)
Picture shows the CLKS 841
SURFACe BOxeS
BILL OF QUANTITy ReQUIReMeNTS Clark-Drain (clear opening) Solid Top Ductile Iron Surface Boxes to BS 5834 Part 3 and BS 750 Grade A, manufactured (CLKS Reference no.) Black bitumen coated from:Clark-Drain Ltd, Station Road, Yaxley, Peterborough, Cambs PE7 3EQ
| 14 | END hiNgED | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | SurfaCE bOxES | 15 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
ANCILLARy GULLy GRATe
CLKS 61
225mm x 225mm x 75mm Gully Grate and Frame
– Class B125
CLKS 60DDI
300mm x 300mm Dished Gully Grate and Frame
– Class B125
CLKS 172 eNB
280mm diameter Ductile Iron Gulley Grate
– Class B125
STeP IRONS
Galvanised malleable Step Irons
Manufactured to BS 1247:1994
Product Code Length (mm)
CLKS 212 115 (Approx box qty 15)
CLKS 213 225 (Approx box qty 10)CLKS 556
CLKS 552
CLKS 212 CLKS 213
CLKS 172 EnB
Manual and Hydraulic LiftersThe CLKS 282 manual lifter is small, light and powerful.
It is simple and fast to assemble and weighing just 15kg can be carried in the boot of a car. It’s remarkably easy to use with no strength required, just turn the handles and the most stubborn of manhole covers is raised. Built to high standards it is rugged and practical.
The CLKS 281 hydraulic lifter is a powerful, fast lifter for heavy duty use.
Quick to assemble and easy to use, this lifter can give up to 1.5 tons of lift, making easy work of the heaviest manhole cover.
LIFTING KeyS
Product Code Description
CLKS 552 Heavy Duty lifting keys
CLKS 556 Light Duty lifting keys
CLKS 776 Recessed Cover lifting keys
Manual lifter CLKS 282
Hydraulic lifter CLKS 281
| 16 | aNCiLLary PrODuCTS | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | maNhOLE LifTErS | 17 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
ANCILLARy PRODUCTS MANHOLe LIFTeRS
CLKS 60DDI
CLKS 61
ANCILLARy GULLy GRATe
STeP IRONS
Product Code Length (mm)
CLKS 556
CLKS 552
CLKS 212 CLKS 213
CLKS 172 EnB
Manual and Hydraulic LiftersThe CLKS 282 manual lifter is small, light and powerful.
It is simple and fast to assemble and weighing just 15kg can be carried in the boot of a car. It’s remarkably easy to use with no strength required, just turn the handles and the most stubborn of manhole covers is raised. Built to high standards it is rugged and practical.
The CLKS 281 hydraulic lifter is a powerful, fast lifter for heavy duty use.
Quick to assemble and easy to use, this lifter can give up to 1.5 tons of lift, making easy work of the heaviest manhole cover.
LIFTING KeyS
Product Code Description
CLKS 552 Heavy Duty lifting keys
CLKS 556 Light Duty lifting keys
CLKS 776 Recessed Cover lifting keys
Manual lifter CLKS 282
Hydraulic lifter CLKS 281
| 16 | aNCiLLary PrODuCTS | www.clark-drain.com | [email protected]
Due to our continual development programme, we reserve the right to upgrade products without prior notice. www.clark-drain.com | [email protected] | maNhOLE LifTErS | 17 |
Due to our continual development programme, we reserve the right to upgrade products without prior notice.
ANCILLARy PRODUCTS MANHOLe LIFTeRS
CLKS 60DDI
CLKS 61
Municipal Castings
Clark-Drain LimitedStation RoadYaxleyPeterborough PE7 3EQ
Telephone: 01733 765317Fax: 01733 246923
Email: [email protected]: www.clark-drain.com
Due to our continual development program we reserve the right to upgrade products without prior notice.Products must be fitted in accordance with Clark-Drain installation guides.
LMRTdesign.com 0054 0711
CLARK-DRAIN PRODUCTS
Galvanised Pressed Steel Covers
Recessed Pavior Range
Internal Recessed Range
Municipal Covers and Frames
Polypropylene Inspection Covers and Frames
Technical Channel
Domestic Channel
One call has it covered!
Your local stockist
40 OverOver