cisco unified border element (cube) integration guide · cisco unified border element (cube)...
TRANSCRIPT
Cisco Unified Border Element (CUBE) Integration Guide - 1
Cisco Unified Border Element (CUBE) Integration Guide
Technical Documentation for integrating Cisco Unified Border Element (CUBE) with
BlueJeans
Table of Contents
Introduction ...................................................................................................................... 2
Architecture ...................................................................................................................... 2
Requirements ...................................................................................................................2
Configuration ....................................................................................................................3
Joining Meetings ............................................................................................................10
Questions? ......................................................................................................................10
Cisco Unified Border Element (CUBE) Integration Guide - 2
Call Flow
Introduction
This document illustrates how to configure Cisco Unified Border Element (CUBE) to allow room
systems that register to a Cisco Unified Communications Manager (CUCM) to connect to a
BlueJeans conference.
Cisco Unified Border Element (CUBE) is a session border controller, providing voice and video
connectivity from the enterprise IP network to service provider SIP trunks. CUBE also offers
services that extend collaboration beyond the firewall to teleworkers and business partners and
help organizations to more easily connect to hosted collaboration services providers.
Architecture
The diagram below captures the overall setup and call flow. The enterprise architecture consists of
the appropriate components based on the Cisco Video deployment guides. In this case, room
systems would register to the CUCM as sip end points and the CUCM would have a SIP trunk for
external video calls to the CUBE. The CUBE is usually deployed in the DMZ as the video edge
device for calls in or out of the enterprise.
Requirements
Customer has the following software versions for the mandatory components:
- Cisco Unified Communications Manager (CUCM) version 9.1.2 or later
- Cisco Unified Border Element (CUBE) version 15.4(2)T1 or later (to support URI dialing).
Cisco Unified Border Element (CUBE) Integration Guide - 3
Configuration
The following steps cover the required one time setup for the CUCM (Cisco Unified Call
Manager) and CUBE (Cisco Unified Border Element).
1. Configure a new SIP Trunk Profile by going to Device > Device Settings > SIP Profiles and
add new profile with values show in Figure 2 (below).
2. Leave all other parameters as default.
Note: If there is already a SIP Profile setup please ensure the configuration matches the below.
Early Offer support is required and you should allow for BFCP for content sharing.
Cisco Unified Border Element (CUBE) Integration Guide - 4
3. Go to the CUCM Administration web interface, click on Device > Trunk and click Add New
4. All other parameters can be set to the default values.
Cisco Unified Border Element (CUBE) Integration Guide - 5
Cisco Unified Border Element (CUBE) Integration Guide - 6
Cisco Unified Border Element (CUBE) Integration Guide - 7
5. Add a route pattern to route the Blue Jeans number from room systems to the CUBE via the SIP
trunk from CUCM. Go to Call Routing > Route/Hunt > Route Pattern and click Add New
Cisco Unified Border Element (CUBE) Integration Guide - 8
6. Configure the CUBE dial peers to route calls to BlueJeans (Outbound Dial peer). Make sure
audio codec is set to G722 and session transport is set to TCP.
Sample:
!
dial-peer voice 100 voip
description Outbound to Bluejeans
destination-pattern 9412567975
session protocol sipv2
session target dns:sip.bjn.vc
session transport tcp
codec g722-64
!
Cisco Unified Border Element (CUBE) Integration Guide - 9
7. Configure the CUBE dial Inbound Dial peer from route calls to BlueJeans. Make sure audio
codec is also set to G722 (may have to add this codec to your configuration).
Sample:
!
dial-peer voice 101 voip
Cisco Unified Border Element (CUBE) Integration Guide - 10
description INBOUND
session protocol sipv2
session target sip-server
incoming uri request 1
codec g722-64
!
May have to add these preferences to your inbound dial peer configuration:
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g722-64
codec preference 3 g711alaw
Joining Meetings
1. Login to BlueJeans and schedule / start a meeting – refer to “Scheduling a Meeting” for
assistance OR if you received an invitation via email, click on the meeting link in the email.
2. To join the meeting: dial 9412567975 from the room system.
3. After a few seconds, the Blue Jeans IVR screen will appear (see below).
4. Enter the Meeting ID to join.
Cisco Unified Border Element (CUBE) Integration Guide - 11
Questions?
Contact BlueJeans support via
Web: www.bluejeans.com
Email: [email protected]
Telephone 408-791-2830
or check the BlueJeans Knowledge Base
BlueJeans
516 Clyde Avenue Mountain View, CA 94070