Cisco CCNA IPV6 Static Configuration

Download Cisco CCNA  IPV6 Static Configuration

Post on 07-Jan-2017

516 views

Category:

Education

10 download

Embed Size (px)

TRANSCRIPT

CISCO CCNA DHCP SERVER

CISCO CCNAIPV6 Static Configuration

To watch our Cisco CCNA Video Trainings Please Check out the link below:www.asmed.com/c1

ASM Educational Center Inc. (ASM)WhereTraining,Technology&ServiceConvergePhone: (301) 984-7400Rockville,MD

IPV6 Static Configuration

IPV6 Static ConfigurationNow I will do small Lab: The Goal is that seated at R4 be able to ping all the loopback of R10 , in order to do this , we will cover Static Route.R4=10.10.10.4R10=10.10.10.10 connected via LAN linkAlso I will have IPV6 as follow:r4 f0/0=2001:4444::4/64r10 f0/0=2001:4444::10/64

IPV6 Static ConfigurationIn here we have R4 and R10 with the following:Here is:

R4#Show runinterface FastEthernet0/0ip address 10.10.10.4 255.255.255.0duplex autospeed autoipv6 address 2001:4444::4/64

IPV6 Static ConfigurationHere is R10 with so many loopback address:interface Loopback0ip address 100.100.100.100 255.255.255.0!interface Loopback1no ip addressipv6 address FEC0:1000::1/128!interface Loopback2no ip addressipv6 address FEC0:1000::2/128!

IPV6 Static Configurationinterface Loopback3no ip addressipv6 address FEC0:1000::3/128!interface Loopback4no ip addressipv6 address FEC0:1000::4/128!interface FastEthernet0/0ip address 10.10.10.10 255.255.255.0duplex autospeed autoipv6 address 2001:4444::10/64

IPV6 Static ConfigurationRight now when i go to R4#show ipv6 route i do not see the loopback from R10 why?Since i need to run do ipv6 Static RouteR4#show ipv6 routeIPv6 Routing Table 3 entriesCodes: C Connected, L Local, S Static, R RIP, B BGPU Per-user Static route, M MIPv6I1 ISIS L1, I2 ISIS L2, IA ISIS interarea, IS ISIS summaryO OSPF intra, OI OSPF inter, OE1 OSPF ext 1, OE2 OSPF ext 2ON1 OSPF NSSA ext 1, ON2 OSPF NSSA ext 2D EIGRP, EX EIGRP externalC 2001:4444::/64 [0/0]via ::, FastEthernet0/0L 2001:4444::4/128 [0/0]via ::, FastEthernet0/0L FF00::/8 [0/0]via ::, Null0

IPV6 Static ConfigurationSo remember you need enable unicast-routingHint:on global Configuration start with IPV6?Here is my configuration on R4#

Step 1) Enable Unicast-routing on R4R4#config tEnter configuration commands, one per line. End with CNTL/Z.R4(config)#ipvR4(config)#ipv6 ?access-list Configure access listscef Cisco Express Forwardingdhcp Configure Ipv6 DHCP

IPV6 Static Configurationgeneral-prefix Configure a general IPv6 prefixhost Configure static hostnamesinspect Context-based Access Control Enginelocal Specify local optionsnat NAT-PT Configuration commandsneighbor Neighborroute Configure static routesrouter Enable an IPV6 routing processunicast-routing Enable unicast routingR4(config)#ipv6 unicast-routing

IPV6 Static ConfigurationStep 2) Now I will configure Static Route, in here I need to put the destination Network inside my R4 router

That is I need to have:ipv6 route FEC0:1000::1/128 2001:4444::10Destination Network (Next Hop address)We must do above commands for all Loopback address , since the goal is that seated at R4I should be able to ping all loopback address located on R10ipv6 route FEC0:1000::2/128 2001:4444::10ipv6 route FEC0:1000::3/128 2001:4444::10ipv6 route FEC0:1000::4/128 2001:4444::10

IPV6 Static ConfigurationNow we will configure it on R4 (using the ? mark)R4#config tEnter configuration commands, one per line. End with CNTL/Z.R4(config)#ipv6 ?access-list Configure access listscef Cisco Express Forwardingdhcp Configure Ipv6 DHCPgeneral-prefix Configure a general IPv6 prefixhost Configure static hostnamesinspect Context-based Access Control Enginelocal Specify local optionsnat NAT-PT Configuration commands

IPV6 Static Configurationneighbor Neighborroute Configure static routesrouter Enable an IPV6 routing processunicast-routing Enable unicast routingR4(config)#ipv6 route ?X:X:X:X::X/ IPv6 prefixR4(config)#ipv6 route FEC0:1000::1/128 ?Ethernet IEEE 802.3FastEthernet FastEthernet IEEE 802.3GigabitEthernet GigabitEthernet IEEE 802.3zLoopback Loopback interfaceSerial SerialVlan Catalyst VlansX:X:X:X::X IPv6 address of next-hop

IPV6 Static ConfigurationR4(config)#ipv6 route FEC0:1000::1/128 2001:4444::10 ? Administrative distance

R4(config)#ipv6 route FEC0:1000::1/128 2001:4444::10R4(config)#Now I will just use up arrow key and put the rest of loopback networkR4(config)#ipv6 route FEC0:1000::1/128 2001:4444::10R4(config)#R4(config)#R4(config)#ipv6 route FEC0:1000::2/128 2001:4444::10R4(config)#ipv6 route FEC0:1000::3/128 2001:4444::10R4(config)#ipv6 route FEC0:1000::4/128 2001:4444::10

IPV6 Static ConfigurationHere is my show run so far on R4#R4#show runipv6 unicast-routing!!!ipv6 route FEC0:1000::1/128 2001:4444::10ipv6 route FEC0:1000::2/128 2001:4444::10ipv6 route FEC0:1000::3/128 2001:4444::10ipv6 route FEC0:1000::4/128 2001:4444::10!

IPV6 Static ConfigurationNow If I try to ping from R4 to the loopback address of R10 , it will work .R4#ping FEC0:1000::1Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to FEC0:1000::1, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 msR4#ping FEC0:1000::2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to FEC0:1000::2, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/1 msR4#ping FEC0:1000::3

IPV6 Static ConfigurationType escape sequence to abort.Sending 5, 100-byte ICMP Echos to FEC0:1000::3, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 msR4#ping FEC0:1000::4Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to FEC0:1000::4, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 0/1/8 msBut if I had some loopback address on the R4 , then R10 can not ping that loopback address , we can use same concept as above or I Canshow you the concept of Default route.I go to R4 and create one Loopback address on R4#

IPV6 Static ConfigurationR4#config tEnter configuration commands, one per line. End with CNTL/Z.R4(config)#int loopback 1R4(config-if)#ipv6 address FEC0:4000::1/128R4(config-if)#R4(config-if)#int loopback 2R4(config-if)#ipv6 address FEC0:4000::2/128R10#

IPV6 Static ConfigurationStep 3) Hint: remember to enable IPV6 unicast-routing on R10R10#config tEnter configuration commands, one per line. End with CNTL/Z.R10(config)#ipvR10(config)#ipv6 unR10(config)#ipv6 ?access-list Configure access listscef Cisco Express Forwardingdhcp Configure Ipv6 DHCPgeneral-prefix Configure a general IPv6 prefixhost Configure static hostnames

IPV6 Static Configurationinspect Context-based Access Control Enginelocal Specify local optionsnat NAT-PT Configuration commandsneighbor Neighborroute Configure static routesrouter Enable an IPV6 routing processunicast-routing Enable unicast routingR10(config)#ipv6 uniR10(config)#ipv6 unicast-routingR10(config)#

IPV6 Static ConfigurationStep 4) Now I will do Default route on R10 and I will use next hop addressR10#ipv6 route ::/0 2001:4444::4Hint:for default route in Ipv4 we use 0.0.0.0 0.0.0.0 but for Ipv6 we will use ::/0

R10#config tEnter configuration commands, one per line. End with CNTL/Z.R10(config)#ipvR10(config)#ipv6 ?access-list Configure access listscef Cisco Express Forwardingdhcp Configure Ipv6 DHCPgeneral-prefix Configure a general IPv6 prefix

IPV6 Static Configurationhost Configure static hostnamesinspect Context-based Access Control Enginelocal Specify local optionsnat NAT-PT Configuration commandsneighbor Neighborroute Configure static routesrouter Enable an IPV6 routing processunicast-routing Enable unicast routingR10(config)#ipv6 routR10(config)#ipv6 route ?X:X:X:X::X/ IPv6 prefixR10(config)#ipv6 route ::/0 ?Ethernet IEEE 802.3FastEthernet FastEthernet IEEE 802.3GigabitEthernet GigabitEthernet IEEE 802.3zLoopback Loopback interface

IPV6 Static ConfigurationSerial SerialVlan Catalyst VlansX:X:X:X::X IPv6 address of next-hopR10(config)#ipv6 route ::/0 2001:4444::4R10(config)#Here is my Show run on R10#ipv6 unicast-routingipv6 route ::/0 2001:4444::4Now seated on R10 I should be able to ping the Loopback address of R4R10#ping FEC0:4000::1

IPV6 Static ConfigurationType escape sequence to abort.Sending 5, 100-byte ICMP Echos to FEC0:4000::1, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/1 msR10#ping FEC0:4000::2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to FEC0:4000::2, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 msR10#

IPV6 Static ConfigurationHere is show Ipv6 route on R4 and R10R4#show ipv6 routeIPv6 Routing Table 9 entriesCodes: C Connected, L Local, S Static, R RIP, B BGPU Per-user Static route, M MIPv6I1 ISIS L1, I2 ISIS L2, IA ISIS interarea, IS ISIS summaryO OSPF intra, OI OSPF inter, OE1 OSPF ext 1, OE2 OSPF ext 2ON1 OSPF NSSA ext 1, ON2 OSPF NSSA ext 2D EIGRP, EX EIGRP externalC 2001:4444::/64 [0/0]via ::, FastEthernet0/0L 2001:4444::4/128 [0/0]via ::, FastEthernet0/0

IPV6 Static ConfigurationS FEC0:1000::1/128 [1/0] via 2001:4444::10S FEC0:1000::2/128 [1/0] via 2001:4444::10S FEC0:1000::3/128 [1/0] via 2001:4444::10S FEC0:1000::4/128 [1/0] via 2001:4444::10C FEC0:4000::1/128 [0/0]via ::, Loopback1C FEC0:4000::2/128 [0/0]via ::, Loopback2L FF00::/8 [0/0]via ::, Null0

IPV6 Static ConfigurationHere is show ipv6 route for R10R10#show ipv6 routeIPv6 Routing Table 8 entriesCodes: C Connected, L Local, S Static, R RIP, B BGPU Per-user Static route, M MIPv6I1 ISIS L1, I2 ISIS L2, IA ISIS interarea, IS ISIS summaryO OSPF intra, OI OSPF inter, OE1 OSPF ext 1, OE2 OSPF ext 2ON1 OSPF NSSA ext 1, ON2 OSPF NSSA ext 2D EIGRP, EX EIGRP externalS ::/0 [1/0] via 2001:4444::4

IPV6 Static ConfigurationC 2001:4444::/64 [0/0]via ::, FastEthernet0/0L 2001:4444::10/128 [0/0]via ::, FastEthernet0/0C FEC0:1000::1/128 [0/0]via ::, Loopback1C FEC0:1000::2/128 [0/0]via ::, Loopback2C FEC0:1000::3/128 [0/0]via ::, Loopback3C FEC0:1000::4/128 [0/0]via ::, Loopback4L FF00::/8 [0/0]via ::, Null0

IPV6 Static ConfigurationHere is summary on R4 and R10 show run:R4#show runinterface Loopback0ip address 4.4.4.4 255.255.255.0!interface Loopback1no ip addressipv6 address FEC0:4000::1/128!interface Loopback2no ip addressipv6 address FEC0:4000::2/128!

IPV6 Static Configurationinterface FastEthernet0/0ip address 10.10.10.4 255.255.255.0duplex autospeed autoipv6 address 2001:4444::4/64!ipv6 route FEC0:1000::1/128 2001:4444::10ipv6 route FEC0:1000::2/128 2001:4444::10ipv6 route FEC0:1000::3/128 2001:4444::10ipv6 route FEC0:1000::4/128 2001:4444::10R10#show runBuilding configurationipv6 unicast-routing!

IPV6 Static Configurationinterface Loopback1no ip addressipv6 address FEC0:1000::1/128!interface Loopback2no ip addressipv6 address FEC0:1000::2/128!interface Loopback3no ip addressipv6 address FEC0:1000::3/128!

IPV6 Static Configurationinterface Loopback4no ip addressipv6 address FEC0:1000::4/128!interface FastEthernet0/0ip address 10.10.10.10 255.255.255.0duplex autospeed autoipv6 address 2001:4444::10/64!!ipv6 route ::/0 2001:4444::4!

ASM Educational Center Inc. (ASM)WhereTraining,Technology&ServiceConvergePhone: (301) 984-7400Rockville,MD

To watch our Cisco CCNA Video Trainings Please Check out the link below:www.asmed.com/c1

Recommended

View more >