circus whitehorse i e ltr

8/12/2019 Circus Whitehorse i e Ltr

1/12

Before starting assembly : Writing the number of each section onits back side before cutting out the sections is highly recommended.(* This way, you can be sure which section is which even aftercutting out the sections.)

Indicates where sections should be glued together.

Indicates the order for assembling parts.

Indicates where to insert sections.Do not glue the sections together.

Round bar : Use to give parts a curved surface.

Tweezers : Useful in working with fine parts.

Cut along the line.

Be sure to buildthis model carefully.

Caution :Performing horses' tricks require two pieces of thread, approximately 20cm long. Use silk or other durable thread.

* Turn the handle to makethe horses prance in timewith the trainer's baton.

Assembly Instructions

Mountain fold(dotted line)Make a mountain fold.

Valley fold(dashed and dotted line)Make a valley fold.

Scissors line(solid line)Cut along the line.

Cut in line(solid line)Cut along the line.

Glue spot(Red dot)Glue parts with the same number together.

Glue spot(Green dot)Glue within the same part.

Glue spot(Blue dot)Glue to the rear of the other part.

Glue

The glue spot(colored dot)shows where to apply the glue.

Tools and materials

Assembly tip

Caution

Scissors, set square, glue(We recommend stick glue), pencil, usedballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Before gluing, crease the paper along mountain fold and valleyfold lines and make sure rounded sections are nice and stiff.

Glue, scissors and other tools may be dangerous to young childrenso be sure to keep them out of the reach of young children.

View of completed model

Assembly Instructions : Twelve US letter sheets (No. 1 to No. 12)

*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold.

* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.

Caution :Spread glue ina thin even layer,then glue parts 7and 8 to the base.

Glue parts 7, 8, and 10 tothe reverseside of part 1.

(Moving) Performing white horses : Assembly Instructions Canon Inc. Hideharu Naitoh & G&P


2/12

Caution :When viewed fromthe side, parts 16and 17 should bealigned exactly.



3/12


Caution :Do not attach the front (part 3)and back (part 6) to the baseat this stage.

Align the star marks whengluing part 14 to part 8.

Parts 16, 17, and 18


4/12

Caution :Align the colored flaps whengluing parts 20 and 22.

Wrap the end of a 20cmpiece of thread aroundthe axle two or three times.

Glue the thread firmlyin place.



5/12

Parts 20 to 22

Make two sets. Make two sets.

Make two sets.

Parts 23 to 26



6/12

Caution :Hold the horses' bodies (part 30)flat to prevent warping as you glueon the other parts.

Make two sets.

Parts 40 and 41

Make two sets.

Confirm movement.



7/12

Caution :Fold the legs carefully as

you glue them togetherto prevent twisting.

Make two sets. Make two sets.



8/12

Caution :Do not attach part 28and parts 42 through44 at this stage.

Caution :Glue the legs so that theyare exactly aligned whenviewed from the side.

Maketwo sets.



9/12

Caution :Do not attach the back(part 6) at this stage.

Insert the support under each horseinto the square hole in the base andglue the hind legs in place.

From inside the base,align part 39 with flapson part 41 and gluefirmly in place.

* Using an empty box or a

similar item for a base makesit easier to work with this modelwhen it is upside down.

* Horses are easier to attach if youglue one leg at a time.

Glue the front (part 3) to the base.



10/12

Caution :Take care when cuttingout the circular holes toensure that they aresmoothly rounded.

Caution :Position part 48 aligned with the upperand lower inner wings on the right side(marked with a star) and glue in place.

Insert the end of the20cm thread into theslot and glue it firmlyin place.

* The star indicates the left arm.

Confirm movement.

three

parts twoparts



11/12

Run the thread through the squarehole and glue the trainer firmly in

place on the base.

With parts A and B in positioned asillustrated below, insert both threadsthrough the slot on part 27 and lightlytake up the tension on both threads.

With both threads inserted into part 27,gently turn the handle to move the trainer'sarms and confirm the movement of the horses.

Apply glue to part 27and glue thread firmlyin place. Trim off anydangling ends of thread.

Maketwo sets.



12/12

Glue on all the remaining parts.

Parts 50 to 52

Finished!


circus whitehorse i e ltr

Documents