cibjo precious metals book 2010-1

8/8/2019 CIBJO Precious Metals Book 2010-1

1/31


2/31


3/31


4/31

CIBJO 2010. All rights reserved. PRECIOUS METALS COMMISSION 2010-1

Foreword

CIBJO is the French acronym for the Confdration Internationale de la Bijouterie, J oaillerie,Orfvrerie, des Diamants, Perles et Pierres, which translates as the InternationalConfederation of Jewellery, Silverware, Diamonds, Pearls and Stones (normally shortened tothe International Jewellery Confederation). Founded in 1926 as BIBOAH, a Europeanorganisation whose mission was to represent and advance the interests of the jewellery tradein Europe, it was reorganised in 1961 and renamed CIBJO, in 2009 it was once againreorganized and officially named CIBJO, The World Jewellery Confederation. Today CIBJO,which is domiciled in Switzerland, is a non-profit confederation of national and internationaltrade associations including commercial organisations involved in the jewellery supply chain. Itnow has members from countries representing all five continents of the world. CIBJO printedits first deliberations on terminology and trade practices in 1968.

It is the task of CIBJO to record the accepted trade practices and nomenclature for the industrythroughout the world. The records of the trade practices complement existing fair tradelegislation of a nation or in the absence of relevant national laws they can be considered astrading standards. In countries where laws or norms exist, which conflict with the laws, normsor trade practices in other countries, CIBJO will support the national trade organizations toprevent trade barriers developing. The purpose of CIBJO is to encourage harmonization,promote international co-operation within the jewellery industry, consider issues which are ofconcern to the trade worldwide and to communicate proactively with members. Foremostamongst these the aim is to protect consumer confidence in the industry. CIBJO pursues all ofthese objectives through informed deliberation and by reaching decisions in accordance withits Statutes. CIBJO relies upon the initiative of its members to support and implement itsstandards, and to protect the trust of the public in the industry.

The work of CIBJO is accomplished through Committees, Commissions and Sectors.Committees and Commissions consider standards for use in the jewellery supply chain.Sectors represent levels of trade in the jewellery industry. Sectors and commissions advise theExecutive Committee on current trade practices and issues that affect the jewellery industry.

Three independent sectors exist within the confederation:

Sector A - The Products SectorSector B - The Supply chain SectorSector C - The Service Sector

The Executive Committee may appoint Commissions that consider detailed issues. At presentthese are:

Coloured Stone

Diamond

Ethics

Gemmological

Pearl

iv


5/31


Marketing & Education

Precious Metals

World Jewellers Vigilance

The Commissions for Diamonds, Gemstones, Pearls and Precious Metals have collated theguidelines, which present the accepted trade practices for applying descriptions to thesematerials. It is in the best interest of all those concerned to be aware of them.

The Sectors and Commissions will propose changes in the standards, also known as the BlueBooks, to the Executive Committee. After review the Executive Committee will submit theaccepted proposals for adoption to the Board of Directors and if approved they will notify theassembly of delegates of the changes at the annual congress. Furthermore it is our mutualresponsibility to support these recommendations, which concern all professional peopleconnected with diamonds, gemstones, pearls and precious metals. CIBJO Standards aresubject to government regulations in the respective jurisdictions of CIBJO members.

The national umbrella organization for each country represents, in principle, all the nationaltrade organizations involved in the sectors mentioned above. This democratic structure, whichhas contributed to CIBJOs world-wide recognition also includes international trade andcommercial organizations, it provides an international forum for the trade to collectively drawattention to issues and implement resulting decisions.

CIBJO Secretariat:

CIBJO, The World Jewellery ConfederationPiazzale Carlo Magno, 120149 Milano, Italy

Tel: +39-02-4997-7098 / 7097 / 6187 Fax: + 39 02- 4997-7059E-mail: [email protected] Web site: www.cibjo.org

v


6/31


Introduction

This CIBJO Precious Metal Standard is designed to assist all those involved in the purchase orsale of platinum, gold, palladium and silver jewellery, flatware and hollow-ware . Thestandard is non-judgmental and the definitions and clauses contained herein are formatted andworded only to ensure that each precious metal item bought or sold is done so with clarity andhonesty. The stability of the market place depends upon the use of the proper nomenclature andthe declaration of all known facts which ensure a fully informed purchase or sale.

In the case of precious metals it is important that those involved in sales or purchases know thefineness in parts per thousand by weight of the precious metal in the alloy being traded.

The Scope (1) of the Standard/rules is set out, as are the Normative References (2). The Termsand Definitions (5) are expansive and are extensively cross referenced throughout the NormativeClauses (4), Annex and Tables. It is important that the reader refers to the relevant Terms andDefinitions when consulting each Normative Clause.

President the CIBJO Precious Metal Commission

May 2010

vi


7/31


PRECIOUS METALS TERMINOLOGY AND CLASSIFICATION

1. Scope

The terminology and classification of precious metals are established with reference tocommercial usage, in conformity with the classifications and practices of the internationalprecious metals and jewellery trades. The terminology and classifications of preciousmetals as set out herein shall be used by all traders participating as members of CIBJOmember organisations within all member nations.

Note: Exceptions may be made if the National Law of a particular member nationconflicts with the clauses herein. National Law always supersedes this CIBJOstandard.

2. Normative references

The Gemstone Book, CIBJO (International Confederation of Jewellery,Silverware, Diamonds, Pearls and Stones), the World Jewellery Con-Federation, Piazzale Carlo Magno, 1, 20149 Milano, Italy. [email protected]

The Diamond Book, CIBJO (International Confederation of Jewellery,Silverware, Diamonds, Pearls and Stones), the World Jewellery Con-Federation, Piazzale Carlo Magno, 1, 20149 Milano, Italy. [email protected] .

The Pearl Book, CIBJO (International Confederation of Jewellery,Silverware, Diamonds, Pearls and Stones), the World Jewellery Con-Federation, Piazzale Carlo Magno, 1, 20149 Milano, Italy. [email protected] .

3. Classification of materials.

4. Normative Clauses.

5. Terms and definitions.

For the purposes of these CIBJO standard/rules, the following terms and definitions apply;

5.1. Precious metals

Precious Metals are platinum (Pt), gold (Au), palladium (Pd) and silver (Ag) in their purestate.

5.2. Precious metal alloy

A precious metal alloy is a solid solution containing at least one precious metal; refer to5.10.

5.3. Precious metal article

A precious metal article is any item of jewellery, or goldsmiths or silversmiths flatware orhollow-ware, made entirely or in part from precious metals and their alloys.

1


8/31


5.4. Fineness

The fineness is the content of the named precious metals measured in terms of parts perthousand by weight of alloy.

5.5. Standard of fineness

The standard of fineness is the minimum content of the named precious metals measuredin terms of parts per thousand by weight of alloy.

5.6. Precious metal coating/plating

A precious metal coating or plating is a layer of precious metal or of precious metal alloyapplied to all, or part of a precious metal article e.g. by chemical, electrochemical,mechanical or physical process. See also 5.16.

5.7. Base metals

Base metals are all metals except platinum, gold, palladium, and silver.

5.8. Weight of Precious Metal

The weight of a precious metal item is always expressed in grams to two decimal places.

5.9. Colour of Precious Metals

Gold Yellow, Red, Rose, Green and White

Platinum WhitePalladium WhiteSilver - White

5.10. This CIBJO standard does not apply to :-

Articles made of alloys of fineness less than 850 for platinum, 333 for gold, 500 forpalladium and 800 for silver. Unless alloys meet these minimum finenesses, articles cannotbe described as platinum, gold, palladium or silver.

5.11. Fineness applied under this CIBJO standard

For platinum: 999, 950, 900, 850For gold 999, 986, 916, 750, 585, 416, 375, 333For palladium 999, 950, 500For silver 999, 925, 835, 830, 800

Note: Other standards of fineness may be recognised by the Precious Metals Commissiondepending on international developments.(Some countries still refer to the fineness of gold in terms of karats or carats. A karat is 1/24 th part of pure golde.g. 18 karat gold is 18/24ths = 750 parts per thousand by weight).

2


9/31


5.12. Tolerance

No negative tolerance is permitted in relation to the standard of fineness indicated on thearticle.

Separate rules for special manufacturing techniques are established by the Precious MetalsCommission.

5.13. Use of solder

Adhesives may be used instead of the permitted solders.

In solder-filled wire, both the solder and the wire must be of the permitted fineness. Wherea lower solder fineness is permitted; the whole of the wire must be to a permitted fineness.

Precious Metals must be soldered with precious metal solders of the same fineness.

Practical exceptions:

Precious metal

The following exceptions are permitted:

Gold

The following exceptions are defined:

Gold alloy articles with a fineness of 750/1000 or more shall be soldered with solder of aminimum fineness of 750/1000 gold.

In the case of gold articles of filigree work and watch cases of the 750 standard the soldershall contain not less than 740 parts of gold per 1,000. For white gold articles of the 750standard the solder shall contain not less than 585 parts of gold per 1,000.

Silver

For silver articles of all finenesses, the solder used shall contain not less than 550 parts ofsilver per 1,000.

Platinum

Solder for platinum articles shall contain at least 800 parts per 1,000 of gold, silver,platinum or palladium,Palladium

Solder for palladium articles of all standards shall contain at least 700 parts per 1,000 ofpalladium.

3


10/31


Mixed precious metal:

The solder can be the permitted solder for the least precious metal fineness.

Precious metal with base metal:

Any suitable solder, including base metal, can be used.

5.14. Use of working base metal parts

Other exceptions:

Base metal parts are permitted as a mechanical function for which precious metals areunsuitable either for strength or durability. Such base metal parts shall not be treated togive the appearance of a precious metal.

For all precious metals (examples)

Steel wires used for the assembling of necklaces (the steel wires must not be used asdecoration);

Magnets for clasps;

Security retainers for tie tacks or badge buttons;

Screws;

Threads.Springs in clasps.

For silver articles only

Clasps - only the tongue in a box snap;

Pins for silver brooches;

Pins for silver badge buttons;

Clips for hair clasps, tie clasps, etc.

5.15. Use of non-metallic substances for filling flatware and hollow-ware

Permitted fillings of non-metallic substances:

Filling the base with non metallic material is permitted for better stability (e.g. candleholders, flowerpots and similar silver articles).

The word filled shall be engraved / embossed on the base to indicate that the grossweight of the item is not all precious metal.

4


11/31


Filling the handles with mastic is allowed (e.g. cutlery, salad servers, carving knives andforks, dessert knives, manicure sets, toilet sets and similar articles. This is a non-exhaustivelist).

5.16. Coating of precious metal articles5.16.1 Permissible coatings

Subject to the provisions of paragraph 5.17.9 concerning the differentiation of colours onmixed articles, the following metallic coatings are permitted:

Metallic coating (for example: galvanic) in accordance with the tables below:

On - Metal Permitted surface coatings COMPLETE COVERAGE

Platinum Rhodium, Platinum, Ruthenium

Titanium based coloured coatings (applied using PVD/CVD technique only)Gold Rhodium, Platinum, Gold, Ruthenium

Titanium based coloured coatings (applied using PVD/CVD technique only)Palladium Rhodium, Platinum, Gold, Palladium, Ruthenium

Titanium based coloured coatings (applied using PVD/CVD technique only)Silver Rhodium, Platinum, Gold, Palladium, Ruthenium, Silver

Titanium based coloured coatings (applied using PVD/CVD technique only)

All greyish-white base metals [e.g. a greyish-white version of Cu/Sn, Cu/Zn/Snalloy coating, greyish-white PCP (Pd/Co) alloy coating or coating with similarproperties etc. as a migration barrier between precious metal coatings and silveritems] As an interlayer only

Inorganic and organic coatings Applied as anti-tarnish treatment in the formof a thin film and should only show negligible change in the basic colour ofsilver metal underneath when examined by the unaided eye

All subject to a. Coatings should meet all health and safety regulations and should not lead to other

undesirable properties in the finished jewellery or silverware articles

b. If a sample from the non-soldered portion is tested by the reference method specifiedin local law without removing the coating, then it must not fail legal fineness standard

specified in the local law

5


12/31


On - Metal Permitted surface coatings PARTIAL COVERAGE

Platinum Rhodium, Platinum, Gold, Palladium, Ruthenium

Coloured inorganic and organic coating (applied using any technique)To be applied as a decorative application in the form of a very thin film to enhance

the beauty of object and not for the purpose of increasing weight. Most of thesurface should be the underlying precious metal clearly visible to the consumer

Gold

Palladium

Silver Rhodium, Platinum, Gold, Palladium, Ruthenium, Silver

Coloured inorganic and organic coatings (applied using any technique).To be applied as a decorative application in the form of a very thin film to enhancethe beauty of the object and not for the purpose of increasing weight. Most of thesurface should be the underlying precious metal clearly visible to the consumer

All subject to a. Coatings should meet all the countries health and safety regulations and do not lead to

other undesirable properties in the finished jewellery or silverware articles b. If a sample from the non-soldered portion is tested by the reference method specified in

local law without removing the coating, then it must not fail to comply with legal finenessstandards specified in the local law

c. Sampling from coloured organic coatings to be avoided if they are applied as a decorativeapplication in the form of a very thin film to enhance the beauty of the object and not forthe purpose of increasing weight, and the colour of the majority base precious metal isvisible to the consumer. When a sample from the non-soldered non-coated portion istested by the reference method specified in local law then it must not fail to comply withlegal fineness standards specified in the local law

d. Any article with excessive coatings particularly when applied for the purpose of increasingweight should be rejected. While taking such a decision consumer interest should beparamount

Note: Although palladium is currently permitted both as a plating on palladium itself and onsilver, recent concerns point to the possibility that palladium may be an allergen, similar tonickel. If this is proven to be the case, then it may lead to removal from the permittedcoatings list, subject to national laws.

Chemical or long-lasting thermal treatments (i.e. sulphured silver, Physical Vapour

Deposition (PVD), Chemical Vapour Deposition (CVD).

The colouring of the surface of articles of precious metal by means of chemicaltransformation of the alloy or its components may be permitted under the terms of thisCIBJO standard as long as the standard of fineness is not altered by the process.

Non-metallic coatings (i.e. enamel, niello).

6


13/31


5.16.2 Declaration of coatings

5.16.2.1 Rhodium coating on yellow gold jewellery is not allowed.

5.16.2.2 When a coating is applied which changes the colour of the precious metal alloy usedto make of the article of jewellery, then the coating must be declared, e.g. when using

gold coatings on silver; ruthenium coatings on any precious metal; titanium basedcolour coatings (applied by PVD/CVD technique only) on any precious metal.

5.16.2.3 When a coating is applied that is the same colour as the alloy used to make of thearticle of jewellery, then it is recommended that the coating be declared, e.g. whenusing rhodium coatings on white gold or silver.

5.17 Marking of precious metal articles

5.17.1 The following minimum marks shall be applied on articles which satisfy the criteria inSection 5 of this CIBJO standard:

A registered responsibility mark as described in paragraph 5.17.3 and the correspondingfineness mark in Arabic numerals in parts per thousand.

These marks can be applied by punching, lasering, casting or engraving on the article.Whenever possible, all marks shall be placed in immediate proximity to each other.

Other marks which are not to be confused with the marks mentioned above are allowed asadditional marks.

5.17.2 The Precious Metals Commission can decide on other methods of marking articles.5.17.3 The responsibility mark referred to in paragraph 5.17.1, shall be registered in an official

register of the State and/or trade organisations and/or one of its assay offices, in whoseterritory the article in question is controlled.

5.17.4 All different standards of fineness listed in this CIBJO standard can be represented.

5.17.5 Articles consisting of more than one fineness of the same precious metals:

Where an article consists of different alloys of the same precious metal, the fineness mark

applied shall be that of the lowest fineness present in the article.

5.17.6 Exception: Gold nuggets

Native gold in the shape of nuggets is allowed unmarked on precious metal articles,irrespective of the standard of fineness and of criteria for the determination of colours.

5.17.7 Articles consisting of parts:

If an article consists of parts which are hinged or readily separable, the above marks shallbe applied to the main part. Where practicable, the mark shall be applied also the lesserparts.

7


14/31


5.17.8 A pendant incorporating a gold or silver ingot fitted with a frame shall be considered astwo separate articles, provided the ingot is loosely fitted and not permanently fixed. Theframe may be accepted as a separate and complete article and marked separately.

5.17.9 Articles consisting of different precious metal alloys.

If an article consists of different precious metal alloys, and if the colour and extent ofeach alloy are clearly visible, the marks referred to in paragraph 5.17.1 shall be applied onthe appropriate precious metal.

If an article consists of different precious metal alloys and if the colour and extent of eachalloy is not visible; the marks referred to in paragraph 5.17.1 shall be that of the leastprecious metal and shall be applied on the least precious metal, currently in order ofplatinum, gold, palladium, silver.

Exceptions:

White gold parts permitted on platinum articles for technical reasons:

On platinum articles, the following parts may be in white gold (750/1000):

Tongues for bracelets and necklets;Moving parts of clips for earrings and brooches;Pins for brooches;Joints and catches for brooches.

8


15/31


Appendix 1CIBJO

Precious Metals Commission Questionnaire - February 2010

Country Australia

RecognisedStandards ofFineness

Gold 999 916 750 585 416 375

Silver 999 925 835 800

Platinum 999 950 900 850

Palladium 999 950 500

TolerancesPermitted

Gold No Negative Tolerance Allowed

Silver No Negative Tolerance Allowed

Platinum No Negative Tolerance Allowed

Palladium No Negative Tolerance Allowed

Country Austria


Gold 999 986 900 750 585

Silver 925 900 835 800

Platinum 950

Palladium

TolerancesPermitted




Palladium

9


16/31


Country Denmark

Recognised

Standards ofFineness

Gold All finenesses in the range 333 - 999

Silver All finenesses in the range 800 - 999

Platinum All finenesses in the range 850 - 999Palladium All finenesses in the range 500 - 999

Note - The concept of standard of fineness is not legally applied in Denmark - onlyminimum finenesses are regulated.

TolerancesPermitted





Country Germany

RecognisedStandardsof Fineness

GoldJewellery may be stamped in all finenesses (mark has to be in thousand parts) customaryare 750, 585, 375, 333 (for utensils such as tableware the law states a minimum finenessof 585)

Silver Jewellery may be stamped in all finenesses (mark has to be in thousand parts) customaryare 925, 835 (for utensils such as tableware the law states a minimum fineness of 800)

Platinum The German law only provides for gold and silver, not for platinum, customary however

are : 950Palladium The German law only provides for gold and silver, not for palladium, customary howeverare : 950 and 500

TolerancesPermitted

Gold 10/1000*

Silver 10/1000*

Platinum

Palladium

* The negative tolerance must not exceed 10/1000, when the object is melted down on

the whole

10


17/31


Country Israel

RecognisedStandards of

Fineness

Gold 999 916 875 750 585 375

Silver 999 925 835 800

Platinum 999 950 900 850Palladium

TolerancesPermitted





Country Italy


Gold 750 585 375

Silver 925 800

Platinum 950 900 850

Palladium 950 500

TolerancesPermitted





11


18/31


Country Kingdom Of Bahrain

Recognised


Gold 916 875 750 585

Silver 925 830

Platinum 950

Palladium

TolerancesPermitted

Gold 915 874 748 583

Silver 923 828

Platinum 950

Palladium

Country Lithuania


Gold 999 916 750 585 375

Silver 999 925 830 800

Platinum 999 950 900 850

Palladium 999 950 850 500

TolerancesPermitted





12


19/31


Country New Zealand


Gold 999 916 750 585 417 375

Silver999 925

Platinum 999 950


TolerancesPermitted





Country Norway

Current RecognisedStandards ofFineness

Gold 750 585

Silver 925 830

Platinum 950

Palladium

New ProposedStandards,Permitted From2011

Gold 999 916 750 585 375Silver 999 925 830 800

Platinum 999 950 900 850

Palladium

TolerancesPermitted




Palladium

13


20/31


Country Saudi Arabia


Gold 999.9 916.6 875 750 Less than 18K is not allowed

Silver 999.9 925 900 800

Platinum 999.9 950 850

Palladium

TolerancesPermitted

Gold 4 Per Thousand is Allowed by Law

Silver 4 Per Thousand is Allowed by Law

Platinum 4 Per Thousand is Allowed by Law

Palladium

Country Switzerland


Gold 999 916 750 585 375

Silver 999 925 800

Platinum 999 950 900 850


TolerancesPermitted





Country Thailand


Gold 999 965 750 585

Silver 999 950Platinum 999 950 900

Palladium 999 650

TolerancesPermitted





14


21/31


Country United Kingdom

Recognised


Gold 999 990 916.6 750 585 375

Silver 999 958 925 800

Platinum 999 950 900 850


TolerancesPermitted





Country USA


Gold 999 750 583 417

Silver 925 900

Platinum 999 950 850

Palladium

TolerancesPermitted

Gold 3 3 3 3

Silver 4 4

Platinum 50* 50* 50*

Palladium

*Includes Solder

15


22/31


CIBJOCountries who have not responded to Questionnaire - Information taken From IAAO 9

Country Belgium


Gold 833 750 585

Silver 925 835

Platinum 950

Palladium

Country Bulgaria


Gold 916 833 750 585 500 333

Silver 950 925 800 750 500

Platinum

Palladium

Country Czech Republic


Gold 999 986 900 750 585

Silver 999 959 925 900 835 800

Platinum 999 950 900 850 800

Palladium

Country Estonia


Gold 375MinimumStandard

Silver 800 MinimumStandard

Platinum 850 MinimumStandard

Palladium 500 MinimumStandard

16


23/31


Country Finland

RecognisedStandards

of Fineness

Gold 999 916 750 585 375

Silver 999 925 830 800

Platinum 999 950 900 850Palladium

Country Hungary


Gold 916 750 585 375

Silver 925 900 835 800

Platinum 950 900

Palladium

Country Ireland


Gold 999 990 916 833 750 585 417 375

Silver 999 958 925 800

Platinum 999 950 900 850

Palladium

Country Latvia


Gold 958 916 900 750 585 583 500 375 333

Silver 960 925 916 875 830 800 750

Platinum 950 850

Palladium 850 500

Country Malta


Gold 916 750 585 375

Silver 959 925 830 800

Platinum

Palladium

17


24/31


Country Poland


Gold 960 750 585 500 375 333

Silver 925 875 830 800

Platinum 950

Palladium

Country Portugal

Recognised

Standardsof Fineness

Gold 999 916 800 750 585 375

Silver 999 925 835 830 800

Platinum 999 950 900 850

Palladium

Country Republic of Cyprus


Gold 916 750 585 375

Silver 925 830 800

Platinum

Palladium

Country Romania


Gold 999 916 900 833 750 585 500 375

Silver 999 925 916 875 800 750

Platinum 950Palladium 950

Country Slovakia


Gold 999 986 900 750 585

Silver 999 959 925 900 835 800

Platinum 999 950 900 850 800

Palladium

18


25/31


Country Slovenia

RecognisedStandards

of Fineness

Gold 999 990 916 900 840 800 750 585 500 417 375 333

Silver 999 925 835 800

Platinum 999 950 900 850Palladium 999 950 500

Country Spain


Gold 999 916 750 585 375

Silver 999 925 800

Platinum 999 950 900 850

Palladium

` Sweden


Gold 375 MinimumStandard

Silver 800 MinimumStandard

Platinum 850 MinimumStandard

Palladium MinimumStandard

Country The Netherlands


Gold 916 833 750 585

Silver 925 835 800

Platinum 950

Palladium

19


26/31


Appendix 2

Supporting StandardsInternationally Recognised Precious Metal Standards in relation to the Jewellery, Watchand Silverware Industries (non-exhaustive).

GOLD

Standard Number Title

ISO 14647:2000 Metallic coatings. Determination of porosity on goldcoatings on metallic substrates. Nitric acid vapour test

ISO 3160-1:1998 Watch-cases and accessories. Gold alloy coverings.General requirements

ISO 27874:2008 Metallic coatings. Electrodeposited gold and gold alloycoatings. Specification and test methods

ISO 10713:1992 Jewellery. Gold alloy coatingsISO 11426:1999 Determination of gold in gold jewellery alloys. Cupellation

method (fire assay)ISO 4524-3:1995 Metallic coatings. Test methods for electrodeposited gold

and gold alloy coatings. Electrographic tests for porosityISO 4524-6:1995 Metallic coatings. Test methods for electrodeposited gold

and gold alloy coatings. Determination of the presence ofresidual salts

ISO 4524-2:2000 Metallic coatings. Test methods for electrodeposited goldand gold alloy coatings. Mixed flowing gas (MFG)environmental tests

ISO 8654:1987 Colours of gold alloys. Definition, range of colours anddesignation

ISO 3160-2:2003 Watch-cases and accessories. Gold alloy coverings.Determination of fineness, thickness, corrosion resistanceand adhesion

ISO 15721:2001 Metallic coatings. Porosity tests. Porosity in gold orpalladium coatings by sulfurous acid/sulfur dioxide vapour

ISO 15720:2001 Metallic coatings. Porosity tests. Porosity in gold orpalladium coatings on metal substrates by gel-bulkelectrography

ISO 10378:2005 Copper, lead and zinc sulfide concentrates.Determination of gold and silver. Fire assay gravimetricand flame atomic absorption spectrometric method

ISO 9202:1991 Jewellery. Fineness of precious metal alloys

ISO 4538:1995 Metallic coatings. Thioacetamide corrosion test (TAA test)

ISO 8442-4:1998 Materials and articles in contact with foodstuffs. Cutleryand table hollow ware. Requirements for gold-platedcutlery

20


27/31


SILVER


ISO 4521:2008 Electrodeposited silver and silver alloy coatings.Specification and test methods

ISO 11427:1993 Determination of silver in silver jewellery alloys.Volumetric (potentiometric) method using potassiumbromide

ISO 13756:1997 Determination of silver in silver jewellery alloys.Volumetric (potentiometric) method using sodium chlorideor potassium chloride

ISO 8442-8:2001 Materials and articles in contact with foodstuffs. Cutleryand table hollow ware. Requirements for silver table anddecorative hollow ware

ISO 8442-7:2001 Materials and articles in contact with foodstuffs. Cutlery

and table hollow ware. Requirements for table cutlerymade of silver, other precious metals and their alloys

ISO 8442-6:2001 Materials and articles in contact with foodstuffs. Cutleryand table hollow ware. Lightly silver plated table hollowware protected by lacquer

ISO 4538:1995 Metallic coatings. Thioacetamide corrosion test (TAA test)ISO 10378:2005 Copper, lead and zinc sulfide concentrates.

Determination of gold and silver. Fire assay gravimetricand flame atomic absorption spectrometric method

ISO 9202:1991 Jewellery. Fineness of precious metal alloysISO 2819:1995 Metallic coatings on metallic substrates. Electrodeposited

and chemically deposited coatings. Review of methodsavailable for testing adhesion

ISO 8442-3:1998 Materials and articles in contact with foodstuffs. Cutleryand table hollow ware. Requirements for silver-platedtable and decorative hollow ware

PLATINUM


ISO 11210:1995 Determination of platinum in platinum jewellery alloys.Gravimetric method after precipitation of diammoniumhexachloroplatinate

ISO 11489:1995 Determination of platinum in platinum jewellery alloys.Gravimetric method after reduction with mercury(I)chloride


21


28/31


PLATINUM - continued


ISO 9202:1991 Jewellery. Fineness of precious metal alloysISO 8442-2:1998 Materials and articles in contact with foodstuffs. Cutlery

and table hollow ware. Requirements for stainless steeland silver-plated cutlery

ISO 11494:2008 Determination of platinum in platinum jewellery alloys -ICP-solution-spectrometric method using Yttrium as

internal standard element

PALLADIUM


ISO 11490:1995 Determination of palladium in palladium jewellery alloys.Gravimetric method with dimethyl glyoximeISO 15720:2001 Metallic coatings. Porosity tests. Porosity in gold or

palladium coatings on metal substrates by gel-bulkelectrography

ISO 15721:2001 Metallic coatings. Porosity tests. Porosity in gold orpalladium coatings by sulfurous acid/sulfur dioxide vapour


ISO 13756:1997 Determination of silver in silver jewellery alloys.Volumetric (potentiometric) method using sodium chlorideor potassium chloride

ISO 11495:2008 Determination of palladium in palladium jewellery alloys -ICP-solution-spectrometric method using Yttrium as

internal standard element

MISCELLANEOUS


ISO 15093:2008 Determination of precious metals in 999 gold, platinumand palladium jewellery alloys by difference method usingICP-OES

ISO 15096:2008 Determination of silver in 999/1000 silver jewellery alloysby difference method using ICP-OES

Work in progress to change existing jewellery standards:

At the present time the focus is on 1811:1999 Reference test method for release of nickel fromproducts intended to come into direct and prolonged contact with the skin.

22


29/31


30/31


References

Convention on the Control and Marking of articles of precious metal, Geneva 1994.

Annexes I and II to the Convention on the Control and Marking of articles of preciousmetal, entered into force on 10 March 2000.

24


31/31


Index

Base metals, 2Base metal working parts, 4CIBJO, ivCIBJO Secretariat, vColour of precious metals, 2Fineness, 2Fineness standard of, 2Marking, 7Non-metallic fillings, 4Precious metals, 1Precious metal alloy, 1Precious metal article, 1Precious metal coating/plating, 2, 5Solder, 3Standards, 7Tolerance, 3Weight of precious metal, 2

cibjo precious metals book 2010-1

Documents