chapter 4 – ohm’s law, power and energy
DESCRIPTION
Chapter 4 – Ohm’s Law, Power and Energy. Introductory Circuit Analysis Robert L. Boylestad. Cause. Effect =. Opposition. 4.1 - Ohm’s Law. Every conversion of energy from one form to another can be related to this equation - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/1.jpg)
Chapter 4 – Ohm’s Law, Power and Energy
Introductory Circuit AnalysisRobert L. Boylestad
![Page 2: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/2.jpg)
4.1 - Ohm’s Law
Every conversion of energy from one form to another can be related to this equation
In electric circuits the effect we are trying to establish is the flow of charge, or current. The potential difference, or voltage between two points is the cause (“pressure”), and the opposition is the resistance encountered
Effect = CauseOpposition
![Page 3: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/3.jpg)
Ohm’s Law
Simple analogy: Water in a hose Electrons in a copper wire are as water in a hose Consider the pressure valve as the applied voltage and
the size of the hose as the factor that determines resistance The absence of pressure in the hose, or voltage across the wire
will result in a system without motion or reaction A small diameter hose will limit the rate at which water will flow,
just as a small diameter copper wire limits the flow of electrons
![Page 4: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/4.jpg)
Ohm’s Law
Developed in 1827 by Georg Simon Ohm For a fixed resistance, the greater the voltage (or
pressure) across a resistor, the more the current, and the more the resistance for the same voltage, the less the current
Current is proportional to the applied voltage and inversely proportional to the resistance
![Page 5: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/5.jpg)
Ohm’s Law
I = E/R
Where: I = current (amperes, A)
E = voltage (volts, V)
R = resistance (ohms, )
![Page 6: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/6.jpg)
4.2 - Plotting Ohm’s Law
Insert Fig 4.6Insert Fig 4.6
![Page 7: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/7.jpg)
Plotting Ohm’s Law
Insert Fig 4.8Insert Fig 4.8
![Page 8: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/8.jpg)
4.3 - Power
Power is an indication of how much work (the conversion of energy from one form to another) can be done in a specific amount of time, that is, a rate of doing work
![Page 9: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/9.jpg)
Power
Power can be delivered or absorbed as defined by the polarity of the voltage and the direction of the current
power is being delivered by a dc source if the current flows from the positive terminal
power is being absorbed by a dc source if the current flows into the positive terminal (a battery being charged)
![Page 10: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/10.jpg)
4.4 - Wattmeters
The wattmeter is a device used to measure the power delivered by a source
Power is a function of both current and voltage levels, so four terminals must be used
2 current terminals (usually larger terminals, to ensure a solid connection)
2 voltage terminals (sometimes 3 when there is a choice of voltage level)
![Page 11: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/11.jpg)
4.5 - Efficiency
Efficiency () of a system is determined by the following equation:
= Po / Pi
Where: = efficiency (decimal number) Po = power output
Pi = power input
![Page 12: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/12.jpg)
Efficiency
The basic components of a generating (voltage) system are depicted below, each component has an associated efficiency, resulting in a loss of power through each stage.
Insert Fig 4.19Insert Fig 4.19
![Page 13: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/13.jpg)
4.6 - Energy
Energy (W) lost or gained by any system is determined by:
W = Pt
Since power is measured in watts (or joules per second) and time in seconds, the unit of energy is the wattsecond (Ws) or joule (J)
![Page 14: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/14.jpg)
EnergyThe wattsecond, however, is too small a quantity for
most practical purposes, so the watthour (Wh) and kilowatthour (kWh), were defined, as follows:
Energy (Wh) = power (W) X time (h)
The Killowatthour meter is an instrument used for measuring the energy supplied to a residential or commercial user of electricity
Energy (kWh)=power (W) x time (h)
1000
![Page 15: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/15.jpg)
Typical wattage ratings of some common household
itemsInsert Table 4.1Insert Table 4.1
![Page 16: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/16.jpg)
Power coming into any facility or item must be limited to ensure that the current through the lines or electrical equipment is not above the rated value
Fuses or circuit breakers are installed where the power enters the installation
Fuses have an internal metallic conductor which begins to melt if the current exceeds the fuse rated value on the case
In recent years fuses have been replaced with circuit breakers. Circuit breakers have an electromagnet that, when the current exceeds the rated value, has sufficient strength to draw the connecting metallic link out of the circuit and open the path
4.7 - Circuit Breakers, GFCIs, and Fuses
![Page 17: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/17.jpg)
Circuit Breakers, GFCIs, and Fuses
National Electrical Code requires that outlets in the bathroom and other sensitive areas be of the Ground Fault Current Interrupt (GFCI) variety
GFCIs are designed to trip more quickly than the standard circuit breaker
GFCI senses differences in input and output currents to the outlet, and trips if they are not the same
![Page 18: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/18.jpg)
4.8 - Applications
Microwave ovens Most rated at 500 W to 1200 W at a frequency of
2.45 GHz Heating occurs because the water molecules in the
food vibrate at such a high frequency that the friction with neighboring molecules causes the heating effect
Most microwaves are between 50% and 60% efficient
![Page 19: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/19.jpg)
Applications
Household wiring Most older homes, without electric heating, have a
100 A service Power is broken down into different circuits utilizing
15 A, 20 A, 30 A and 40 A protective breakers Maximum load on each breaker should not exceed 80%
of its rating (12 A of a 15 A circuit breaker)
![Page 20: Chapter 4 – Ohm’s Law, Power and Energy](https://reader033.vdocuments.site/reader033/viewer/2022061520/56812b1c550346895d8f10da/html5/thumbnails/20.jpg)
Applications
The correct gauge of wire must be used with the right circuit breaker – #14 wire up to a 15 A breaker, #12 wire up to 20 A, #10 wire up to 30 A
Grounding is a very important part of safety The National Electric Code requires that the neutral
wire of a system be grounded to an earth-driven rod, a metalic water piping system of 10 ft or more, or a buried metal plate