chapter 4 dimensioning - 2010
TRANSCRIPT
Copyright ©2009 by K. PlantenbergRestricted use only
Chapter 4:Dimensioning
Basic TopicsAdvanced Topics
Exercises
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning: Basic TopicsSummary4-1) Detailed Drawings4-2) Learning to Dimension4-3) Dimension Appearance and Techniques.4-4)
Dimensioning and Locating Simple Features.
4-6) Dimension Choice.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning: Advanced Topics4-5)
Dimensioning and Locating Advanced Features.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning: ExercisesExercise 4-1: Dimension typeExercise 4-2: Spacing and readability 1Exercise 4-3: Spacing and readability 2Exercise 4-4: Duplicate dimensionsExercise 4-5: Dimension placementExercise 4-6: Circular and rectangular viewsExercise 4-7: Dimensioning and locating featuresExercise 4-8: Advanced featuresExercise 4-9: Dimension accuracyExercise 4-10: Round off
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning: ExercisesExercise 4-11: Dimension choiceExercise 4-14: Dimensioning 1Exercise 4-15: Dimensioning 2Exercise 4-16: Dimensioning 3Exercise 4-17: Dimensioning 4
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
Summary
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Summary What will we learn in Chapter 4?
→ How to dimension an orthographic projection using proper dimensioning techniques.
Key points → Dimensions affect how a part is
manufactured.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
4-1) Detailed Drawings
Copyright ©2009 by K. PlantenbergRestricted use only
Detailed Drawings Orthographic Projection: A shape
description of an object (front, top, right side views).
Detailed Drawing: An orthographic projection, complete with all the dimensions and specifications needed to manufacture the object.
Copyright ©2009 by K. PlantenbergRestricted use only
Detailed Drawing Example
Copyright ©2009 by K. PlantenbergRestricted use only
Detailed Drawings Should we dimension an object using the
dimensions that we used to draw the object?No
These are not necessarily the same dimensions required to manufacture it.
We need to follow accepted standards. (ASME Y14.5 – 1994)
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
4-2) Learning To Dimension
Copyright ©2009 by K. PlantenbergRestricted use only
Learning to Dimension What is our goal when dimensioning a
part?→ Basically, dimensions should be given in a
clear and concise manner and should include everything needed to manufacture and inspect the part exactly as intended by the designer.
Copyright ©2009 by K. PlantenbergRestricted use only
Learning to Dimension Proper dimensioning techniques
require the knowledge of the following three areas. → Dimension Appearance/Technique → Dimensioning and Locating Features→ Dimension Choice
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
4-3) Dimension Appearance and Techniques
Copyright ©2009 by K. PlantenbergRestricted use only
Learning to Dimension Dimension Appearance/Technique:
Dimensions use special lines, arrows, symbols and text.
a) The lines used in dimensioning.b) Types of dimensions.c) Dimension symbols.d) Dimension spacing and readability. e) Dimension placement.
Copyright ©2009 by K. PlantenbergRestricted use only
Lines used in Dimensioning Dimensioning requires the use of
→ Dimension lines→ Extension lines→ Leader lines
All three line types are drawn thin so that they will not be confused with visible lines.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimension Line Dimension line: A line terminated by
arrowheads, which indicates the direction and extent of a dimension.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimension Line Dimension line: Ideally, the dimension
line is broken to allow for the insertion of the feature’s size.
Copyright ©2009 by K. PlantenbergRestricted use only
Extension Line Extension line: An extension line is a
thin solid line that extends from a point on the drawing to which the dimension refers.
Long extension lines should be avoided.
Copyright ©2009 by K. PlantenbergRestricted use only
Leader Line Leader Line: A straight inclined thin solid
line leading to a note or dimension value.
Copyright ©2009 by K. PlantenbergRestricted use only
Leader Line Leaders may be terminated:
→ with an arrow, if it ends on the outline of an object.
Copyright ©2009 by K. PlantenbergRestricted use only
Leader Line Leaders may be terminated:
→ with a dot or nothing if it ends within the outline of an object.
Copyright ©2009 by K. PlantenbergRestricted use only
Leader Line Avoid!
→ Crossing leaders.→ Long leaders.→ Leaders that are parallel to adjacent
dimension, extension or section lines.→ Small angles between the leader and the
terminating surface.
Copyright ©2009 by K. PlantenbergRestricted use only
Arrowheads Arrowheads are drawn between the
extension lines if possible. If space is limited, they may be drawn on the outside.
Copyright ©2009 by K. PlantenbergRestricted use only
Types of Dimensions Dimensions are given in the form of
linear distances, angles, and notes.
→ Linear distances: They are usually arranged horizontally or vertically, but may also be aligned with a particular feature of the part.
Copyright ©2009 by K. PlantenbergRestricted use only
Types of Dimensions Dimensions are given in the form of
linear distances, angles, and notes.
→ Angles: Used to give the angle between two surfaces or features of a part.
Copyright ©2009 by K. PlantenbergRestricted use only
Types of Dimensions Dimensions are given in the form of
linear distances, angles, and notes.
→ Notes: Used to dimension diameters, radii, chamfers, threads, and other features that can not be dimensioned by the other two methods.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-1
Dimension types
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-1 Count the different types of dimensions.
→ How many linear horizontal dimensions are there? 5
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-1 Count the different types of dimensions.
→ How many linear vertical dimensions are there? 3
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-1 Count the different types of dimensions.
→ How many angular dimensions are there? 1
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-1 Count the different types of dimensions.
→ How many leader line notes are there? 1
Copyright ©2009 by K. PlantenbergRestricted use only
Lettering Lettering should be legible, easy to
read, and uniform throughout the drawing. → Upper case letters should be used for all
lettering unless a lower case is required. → The minimum lettering height is 0.12 in (3
mm).
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Symbols Dimensioning symbols replace text.
→ The goal of using dimensioning symbols is to eliminate the need for language translation.
Why is it important to use symbols.→ How many products are designed in the
United States?→ How many products are manufactured or
assembled in the United States?
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning SymbolsTerm SymbolDiameter nSpherical diameter SnRadius RSpherical radius SRReference dimension (8)Counterbore / Spotface vCountersink wNumber of times or places 4X
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning SymbolsTerm SymbolDepth / Deep xDimension not to scale 10 Square (Shape) oArc lengthConical Taper y
Slope z
Symmetry i
5
Copyright ©2009 by K. PlantenbergRestricted use only
Spacing and Readability Dimensions should be easy to read,
and minimize the possibility for conflicting interpretations.
Copyright ©2009 by K. PlantenbergRestricted use only
Spacing and Readabilitya) The spacing between dimension lines
should be uniform throughout the drawing.
b) Do not dimension inside an object or have the dimension line touch the object unless clearness is gained.
Copyright ©2009 by K. PlantenbergRestricted use only
Spacing and Readabilityc) Dimension text should be horizontal
which means that it is read from the bottom of the drawing.
d) Dimension text should not cross dimension, extension or visible lines.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-2
Spacing and Readability 1
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-2 List the dimensioning mistakes and then
dimension the object correctly.
What are the 5 types of dimensioning mistakes?
1) Spacing
5) Missing dim. (n of hole)
3) Text
4) No Gap
2) Don’t dim. inside the object.
Correctly Dimensioned
Copyright ©2009 by K. PlantenbergRestricted use only
Spacing and Readabilitye) Dimension lines should not cross
extension lines or other dimension lines.→ Extension lines can cross other extension
lines or visible lines.
f) Extension lines and centerlines should not connect between views.
Copyright ©2009 by K. PlantenbergRestricted use only
Spacing and Readabilityg) Leader lines should be straight, not
curved, and point to the center of the arc or circle at an angle between 30o – 60o.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-3
Spacing and Readability 2
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-3 List the dimensioning mistakes and then
dimension the object correctly.
What are the 4 types of dimensioning mistakes?
3) Text
2) Center line
4) Crossing dim. and ext. line
1) Leader line
Correctly Dimensioned
Copyright ©2009 by K. PlantenbergRestricted use only
Spacing and Readabilityh) Dimensions should not be duplicated or
the same information given in two different ways. → If a reference dimension is used, the size
value is placed within parentheses (e.g. (10) ).
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-4
Duplicate dimensions
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-4 Find the
duplicate dimensions and cross out the ones that you feel should be omitted.
Are there any duplicatesin this group?Which one shouldbe omitted?
Are there any duplicatesin this group?
Which onesshouldbe omitted?
Are there any duplicatesin this group?Which one shouldbe omitted?
Copyright ©2009 by K. PlantenbergRestricted use only
Dimension Placement Dimensions should be placed in such a
way as to enhance the communication of your design.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimension Placementa) Dimensions should be grouped
whenever possible.
b) Dimensions should be placed between views, unless clearness is promoted by placing some outside.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimension Placementc) Dimensions should be attached to the
view where the shape is shown best.
d) Do not dimension hidden lines.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-5
Dimension placement
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-5 List the
dimensioning mistakes and then dimension the object correctly.
What are the 6 types of dimensioning mistakes?
1) Between views
2) Leaders float up
3) Don’t dim. Hidden lines
4) Dim where feature is shown best
6) Long ext. line
5) Group
Correctly Dimensioned
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
4-4) Dimensioning and Locating Simple Features
Copyright ©2009 by K. PlantenbergRestricted use only
Learning to Dimension Dimensioning and Locating Features:
Different types of features require unique methods of dimensioning.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresa) A circle is dimensioned by its diameter
and an arc by its radius using a leader line and a note.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-6
Circular and rectangular views
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-6 Answer questions
about the cylindrical and hole features of the part shown.
Find the hole and cylinder.
Which view is considered the circular view and which is considered the rectangular view?
Circular view
Rectangular view
Looking at just the top view, can you tell the difference between the hole and the cylinder?
No
So that the cylinder is not confused with a hole.
Why is the diameter of the hole given in the circular view and diameter of the cylinder given in the rectangular view?
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresb) Holes are
dimensioned by giving their diameter and location in the circular view.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresc) A cylinder is
dimensioned by giving its diameter and length in the rectangular view, and is located in the circular view.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresd) The depth of a blind hole may be
specified in a note and is the depth of the full diameter from the surface of the object.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featurese) If a hole goes completely through the
feature and it is not clearly shown on the drawing, the abbreviation “THRU” follows the dimension.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresf) If a dimension is given to the center of a
radius, a small cross is drawn at the center.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresf) Where the center location of the radius is
unimportant, the drawing must clearly show that the arc location is controlled by other dimensioned features such as tangent surfaces.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresg) A complete sphere is dimensioned by its
diameter and an incomplete sphere by its radius.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresh) Repetitive features or dimensions may
be specified by using the symbol “X” along with the number of times the feature is repeated. → There is no space between the number of
times the feature is repeated and the “X” symbol, however, there is a space between the symbol “X” and the dimension.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-7
Dimensioning and locating features
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-7 Dimension the object shown.
How do we dimension the hole diameters?
How do we locate the holes?
How do we dimension the cylinder diameters?
How do we dimension the cylinder heights?
Completely dimensioned.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
4-5) Dimensioning and Locating Advanced Features
Skip advanced topic
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresa) If space is at
a minimum, the size and location of a radii may be given by using a false center and jogged dimensions.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresb) Solid parts with rounded ends
® Give the overall dimension. ® Partially rounded ends: radii are also given.® Fully rounded ends: radii are indicated but
the value is not given.®
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresc) Slots
® Overall dimension, or dimension between centers.
® Overall width. ® The radii are
indicated but the value is not given.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresd) The length of an arc is dimensioned
using the arc length symbol.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featurese) Equally spaced features
# of spaces
Space dim
Total distance
Reference
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featurese) Equally spaced features
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresf) If a part is symmetric, it is only necessary
to dimension to one side of the center line of symmetry.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresg) Counterbored holes
Drill DIA
C’Bore DIA
C’Bore depth
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresg) If the thickness of the material below the
counterbore is significant, this thickness rather than the counterbore depth is given.
Copyright ©2009 by K. PlantenbergRestricted use only
Application Question 4-1 What do you think a counterbored hole is
used for?
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresh) Spotfaced Holes: The difference between
a C’BORE and a Spotface is that the machining operation occurs on a curved surface.
Notice that the depth can not be specified in the note.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresi) Countersunk Holes
Drill DIA
Drill Depth
C’Sink DIA
C’Sink angle
Space
Copyright ©2009 by K. PlantenbergRestricted use only
Application Question 4-2 What do you think a countersunk hole is
used for?
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresj) Chamfers: Dimensioned by a linear
dimension and an angle, or by two linear dimensions.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning Featuresj) Chamfers: Dimensioned by a linear
dimension and an angle, or by two linear dimensions.
Space
Copyright ©2009 by K. PlantenbergRestricted use only
Application Question 4-3 What do you think a chamfer is used for?
Safety.
Improve engagement of mating parts.
Copyright ©2009 by K. PlantenbergRestricted use only
Drawing Notes Drawing notes give additional
information that is used to complement conventional dimension. → manufacturing requirements → treatments and finishes → blanket dimensions (e.g. size of all rounds
and fillets on a casting or a blanket tolerance).
The note area is identified with the heading “NOTE:”.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-8
Advanced features
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-8 List the
dimensioning mistakes and then dimension the object correctly.
What are the 7 types of dimensioning mistakes?
1) Use symbols
2) Spaces 3) Angle up5) Radius
7) Locate radius center
6) Don’t dim. hidden features
4) Dim. where features is shown best
Correctly Dimensioned
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
4-6) Dimension Choice
Copyright ©2009 by K. PlantenbergRestricted use only
Learning to Dimension Dimension Choice: Your choice of
dimensions will directly influence the method used to manufacture the part.
a) Units and decimal places. b) Locating feature using datums. c) Dimension accuracy and error build up.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimension Choice Dimension placement and dimension
text influences the manufacturing process used to make the part. → Manufacturing process should not be
specifically stated on the drawing.
Choose dimensions based on function first then manufacturing.
Copyright ©2009 by K. PlantenbergRestricted use only
Units and Decimal Placesa) Decimal dimensions should be used for
all machining dimensions. → You may encounter a drawing that specifies
standard drills, broaches, and the like by size.
→ For drill sizes that are given by number or letter, a decimal size should also be given.
Copyright ©2009 by K. PlantenbergRestricted use only
Units and Decimal Placesb) On drawings where all the dimensions
are either in inches or millimeters the following note should be used.
® UNLESS OTHERWISE SPECIFIED, ALL DIMENSION ARE IN MILLIMETERS (or INCHES)
Copyright ©2009 by K. PlantenbergRestricted use only
Units and Decimal Placesb) If an inch dimension is given on a
millimeter drawing or visa versa, the abbreviations IN or mm should be placed after the dimension value.
Copyright ©2009 by K. PlantenbergRestricted use only
Units and Decimal Placesc) Metric dimensions are given in ‘mm’ and
to 0 or 1 decimal place (e.g. 10, 10.2). → When the dimension is less than a
millimeter, a zero should proceed the decimal point (e.g. 0.5).
Copyright ©2009 by K. PlantenbergRestricted use only
Units and Decimal Placesd) English dimensions are given in ‘inches’
and to 2 decimal places (e.g. 1.25). → A zero is not shown before the decimal point
for values less than one inch (e.g. .75).
Copyright ©2009 by K. PlantenbergRestricted use only
Units and Decimal Placese) Metric 3rd angle drawings are
designated by the SI symbol.
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datums Consider three mutually perpendicular
datum planes. → These planes are imaginary and
theoretically exact.
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datums Now, consider a part that touches all
three datum planes. → The surfaces of the part that touch the
datum planes are called datum features.
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datums Most of the time, features on a part are
located with respect to a datum feature.
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datums
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datums How do we choose which surface will
be a datum feature?
Good datum features are: → functionally important surfaces → mating surfaces → big enough to permit its use in
manufacturing the part
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datums In a class setting, do we always know the
function of the part?
No
We need to make an educated guess as to the function of the part.
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datumsa) Datum dimensioning is preferred over
continuous dimensioning.
Copyright ©2009 by K. PlantenbergRestricted use only
Locating Features Using Datumsb) Dimensions should be given between
points or surfaces that have a functional relation to each other → Slots, mating hole patterns, etc...
Copyright ©2009 by K. PlantenbergRestricted use only
Application Question 4-4 Why is the distance between the two
holes functionally important?
If the hole pattern mates with 2 pins or bolts, the distance between the holes is more important than the distance from the edge to the second hole.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimension Accuracy There is no such thing as an "exact"
measurement. → Every dimension has an implied or stated
tolerance associated with it. → A tolerance is the amount a dimension is
allowed to vary.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-9
Dimension Accuracy
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-9 Which dimensions have implied
tolerances and which have stated tolerances?
Implied StatedImplied
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-9 Does the arrow indicate an increasing
or decreasing accuracy?Increasing
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-9 Write down the range in which the
dimension values are allowed to vary.> 0.5< 1.5
> 0.95< 1.05
0.9991.001
Copyright ©2009 by K. PlantenbergRestricted use only
Rounding Off The more accurate the dimension the
more expensive it is to manufacture. → To cut costs it is necessary to round off
fractional dimensions.
Copyright ©2009 by K. PlantenbergRestricted use only
Rounding Off How do we round off?
→ Let’s round off to the second decimal place.
1.125
2nd decimal place 3rd decimal place
Copyright ©2009 by K. PlantenbergRestricted use only
Rounding Off If the third decimal place number is:
→ less than 5, we truncate after the second decimal place.
1.123 1.12
Copyright ©2009 by K. PlantenbergRestricted use only
Rounding Off If the third decimal place number is:
→ greater than 5, we round up and increase the second decimal place number by 1.
1.126 1.13
Copyright ©2009 by K. PlantenbergRestricted use only
Rounding Off If the third decimal place number is:
→ exactly 5, whether or not we round up depends on if the second decimal place number is odd or even. If it is odd, we round up and if it is even, it is kept the same.
1.165 1.16
1.135 1.14
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-10
Rounding Off
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-10 Round off the following fractions to
two decimal places according to the rules stated above.(5/16) .3125 ®
(5/32) .1562 ®
(1/8) .125 ®
(3/8) .375 ®
.31
.16
.12
.38
Copyright ©2009 by K. PlantenbergRestricted use only
Cumulative Tolerances Continuous dimensioning has the
disadvantage of accumulating error. → It is preferable to use datum dimensioning to
reduce error buildup.
Copyright ©2009 by K. PlantenbergRestricted use only
Cumulative Tolerances What is error build up?
→ e = individual dimension error
x.e 3x.e
x.e + x.e + x.e = 3x.3e
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-11
Dimension Choice
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-11 List the dimensioning mistakes and then
dimension the object correctly.
What are the 5 dimensioning mistakes?
1 & 2) 2 decimal places / No leading zero
4) Symbol 5) Decimal
3) Use datum dimensioning
6) Don’t dim. hidden features
Correctly Dimensioned
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-14
Dimensioning 1
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-14 Dimension
the following object using proper dimensioning techniques.
Did we need the right side view?
Notice the datum features that were used.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-15
Dimensioning 2
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-15 Dimension the following object using
proper dimensioning techniques.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-16
Dimensioning 3
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-16 Dimension the following object using
proper dimensioning techniques.
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-17
Dimensioning 4
Copyright ©2009 by K. PlantenbergRestricted use only
Exercise 4-17 Dimension
the following object using proper dimensioning techniques.
Copyright ©2009 by K. PlantenbergRestricted use only
Dimensioning
The End