chapter 10 digital integrated circuits 10-1 introduction introduction 10-2 special characteristics...
TRANSCRIPT
![Page 1: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/1.jpg)
Chapter 10 Digital Integrated Circuits
10-1 10-1 Introduction
10-2 10-2 Special Characteristics
10-3 10-3 Bipolar-Transistor Characteristics
10-4 10-4 RTL and DTL Circuits
10-5 10-5 Transistor -Transistor Logic
![Page 2: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/2.jpg)
10-6 10-6 Emitter-Coupled Logic
10-7 10-7 Metal-Oxide Semiconductor (MOS)
10-8 10-8 Complementary MOS (CMOS)
10-9 10-9 CMOS Transmission Gate Circuits
Chapter 10 Digital Integrated Circuits
10-10 10-10 Switch-Level Modeling With HDL
![Page 3: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/3.jpg)
10-1 Introduction
IC digital logic family
RTL ( Resistor-transistor logic)
DTL ( Diode-transistor logic)
TTL ( Transistor-transistor logic)
ECL ( Emitter-coupled logic)
MOS ( Metal-oxide semiconductor)
CMOS ( Complementary metal-oxide semiconductor)
![Page 4: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/4.jpg)
10-1 Introduction
NAND gate
If any input of a NAND gate is low, the output is high.
If all inputs of a NAND gate are high, the output is low.
![Page 5: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/5.jpg)
10-1 Introduction
NOR gate
If any input of a NOR gate is high, the output is low.
If all inputs of a NOR gate are low, the output is high.
![Page 6: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/6.jpg)
10-2 Special Characteristics
Fan-Out
The fan-out of a gate specifies the number of standard loads that can be connected to the output of the gate without degrading its normal operation.
The fan-out is calculated from the amount of current available in the output of a gate and the amount of current needed in each input of a gate.
![Page 7: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/7.jpg)
10-2 Special Characteristics
Fan-Out
The fan-out of the gate is calculated from the ratio IOH/IIH or IOL/IIL, whichever is smaller.
![Page 8: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/8.jpg)
10-2 Special Characteristics
Power DissipationThe power dissipation is a parameter that represents the amount of power needed by the gate.The power is the product VCC × ICC .
Supply voltageThe current that is drawn by the circuit.
The current drain from the power supply depends on the logic state of the gate.
The average current is ICC (avg) = ( ICCH + ICCL) /2
The current that is drawn from the power supply when the output of the gate is in the high-voltage level
The current that is drawn from the power supply when the output of the gate is in the low-voltage level
![Page 9: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/9.jpg)
10-2 Special Characteristics
Power DissipationThe average power dissipation
PD (avg) = ICC (avg) × VCC
In a typical digital system there will be many IC, and the power required by each IC must be considered. The total power dissipation in the system is the sum total of the power dissipated in the all ICs.
![Page 10: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/10.jpg)
10-2 Special Characteristics
Propagation DelayThe propagation delay of a gate is the average transition-delay time for the signal to propagate from input to output when the binary signal changes in value.
The signal-delay time between the input and output when the output changes from the high to the low level is referred to as tPHL
![Page 11: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/11.jpg)
10-2 Special Characteristics
Propagation DelayThe propagation delay of a gate is the average transition-delay time for the signal to propagate from input to output when the binary signal changes in value.
When the output goes from the low to the high level, the delay is tPLH
![Page 12: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/12.jpg)
10-2 Special Characteristics
Noise Margin
Noise is a term used to denote an undesired signal that is superimposed upon the normal operating signal.
Noise margin is the maximum noise voltage added to an input signal of a digital circuit that does not cause an undesirable change in the circuit output
![Page 13: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/13.jpg)
10-2 Special Characteristics
Noise Margin
Noise margin is the difference VOH -VIH or VIL -VOL , whichever is smaller.
![Page 14: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/14.jpg)
10-3 Bipolar-Transistor Characteristics
Region VBE(V) VCE(V)
Current Relationsh
ip
Cutoff
Active
Saturation
< 0.6
0.6-0.7
0.7-0.8
Open circuit
> 0.8
0.2
IB = IC = 0
IC = hFEIB
IB >=ICS/hFE
![Page 15: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/15.jpg)
10-3 Bipolar-Transistor Characteristics
Demonstration
Consider the inverter circuit of the figure with the following parameters:
RC = 1KΩ VCC = 5V
RB = 22KΩ H = 5V
hFE = 50 L = 0.2 V
![Page 16: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/16.jpg)
10-3 Bipolar-Transistor Characteristics
Demonstration
IB = (Vi – VBE) / RB = (5 – 0.7) / 22KΩ = 0.195mA
ICS = (VCC – VCE) / RC
= (5 – 0.2) /1KΩ = 4.8mA
0.195 = IB >= ICS/hFE = 4.8/50 =0.096mA
Assuming VCE =0.2V
The transistor is saturated and its output voltage VO = VCE =0.2V= L
![Page 17: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/17.jpg)
10-4 RTL and DTL Circuit
RTL Basic Gate
If all inputs are low at 0.2 V, all transistors are cut off. This causes the output of the circuit to be high.
![Page 18: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/18.jpg)
10-4 RTL and DTL Circuit
RTL Basic Gate
If any input of the RTL gate is high, the corresponding transistor is driven into saturation. This causes the output to be low, regardless of the states of the other transistors.
![Page 19: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/19.jpg)
10-4 RTL and DTL Circuit
DTL Basic Gates
If any input of the gate is low at 0.2V, the corresponding input diode conducts current through VCC and the 5K resistor into the input node.
The voltage of P is equal to a total of 0.9V that is not enough to overcome the a potential of one VBE drop plus two diode drop. The transistor is cutoff. The output voltage is high at 5V.
![Page 20: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/20.jpg)
10-4 RTL and DTL Circuit
DTL Basic Gates
If all inputs are high, the transistors is driven into the saturation region. This causes the output to be low.
![Page 21: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/21.jpg)
10-4 RTL and DTL Circuit
DTL Basic Gates
The fan-out of a DTL gate may be increased by replacing one of the diodes in the base circuit with a transistor.
![Page 22: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/22.jpg)
10-5 Transistor -Transistor Logic
TTL gates have three different types of output configuration:
1. Open-collector output
2. Totem-pole output
3. Three-state (or tristate) output
The original basic TTL gate was a slight improvement over the DTL gate.
![Page 23: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/23.jpg)
10-5 Transistor -Transistor Logic
The basic TTL gate is a modified circuit of the DTL gate
Open-Collector Output Gate
![Page 24: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/24.jpg)
10-5 Transistor -Transistor Logic
The basic TTL gate is a modified circuit of the DTL gate
Open-Collector Output Gate
![Page 25: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/25.jpg)
10-5 Transistor -Transistor Logic
The basic TTL gate is a modified circuit of the DTL gate
Open-Collector Output Gate
![Page 26: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/26.jpg)
10-5 Transistor -Transistor Logic
If any input is low, the voltage at the base of Q1 is equal to 0.9V.
Open-Collector Output Gate
0.2V0.9V
1.8V
In order for Q3 to start conducting, the voltage at the the base of Q1 must be greater than 1.8V.
Therefore, the output transistor is cutoff.
![Page 27: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/27.jpg)
10-5 Transistor -Transistor Logic
If all input are high, both Q2 Q3 conduct and saturate. The base voltage of Q1 is equal to the voltage across its base-collector pn junction plus two VBE drop in Q2 and Q3, or 2.1V.
Open-Collector Output Gate
3V2.1V
The output transistor saturates, the output
goes low to 0.2V
![Page 28: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/28.jpg)
10-5 Transistor -Transistor Logic
If the output of several open-collector TTL gates are tied together with a single external resistor, a wired-AND logic is performed.
Open-Collector Output Gate
The wire-AND logic gives a high level only if all variables are high; otherwise, the function is low.
![Page 29: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/29.jpg)
10-5 Transistor -Transistor Logic
Open-Collector Output Gate
The wire-AND gate is not a physical gate, but only a symbol to designate the function obtained from the indicated connection.
![Page 30: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/30.jpg)
10-5 Transistor -Transistor Logic
Open-Collector Output Gate
Open-collector gates can be tied together to form a common bus.
Three of the inputs are 0, which produces a 1 on the bus. The fourth input, I4, can now transmit information through the common-bus line into inverter 5.
![Page 31: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/31.jpg)
10-6 Emitter-Coupled LogicDifferential
input amplifier
Internal temperature and voltage compensated bias network
Emitter-follower outputs
![Page 32: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/32.jpg)
10-6 Emitter-Coupled Logic
Two outputs of two or more ECL gates can be connected together to form wired logic.
The graphic symbol of ECL Gate
Wired-OR
Wired-AND
![Page 33: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/33.jpg)
10-7 Metal-Oxide Semiconductor (MOS)
Inverter
1. When the input voltage is low (below VT), Q2 turns off. The output voltage is at about VDD.
2. When the input voltage is high (above VT), Q2 turns on. The output voltage is at a voltage below VT.
![Page 34: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/34.jpg)
10-7 Metal-Oxide Semiconductor (MOS)
NAND Gate
1. Input A and B must both be high for all transistors to conduct and cause the output to go low.
2. If either input is low, the corresponding transistor is turned off and the output is high.
1
1
0
![Page 35: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/35.jpg)
10-7 Metal-Oxide Semiconductor (MOS)
NAND Gate
1. Input A and B must both be high for all transistors to conduct and cause the output to go low.
2. If either input is low, the corresponding transistor is turned off and the output is high.
0
1
1
![Page 36: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/36.jpg)
10-7 Metal-Oxide Semiconductor (MOS)
NOR Gate
1. If either input is high, the corresponding transistor conducts and the output is low.
2. If all inputs are low, all active transistors are off and the output is high.
![Page 37: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/37.jpg)
10-8 Complementary MOS (CMOS)
Inverter
1. When the input is low, both gates are zero potential. The input is at –VDD, relative to the source of the p-channel device and at 0 V relative to the source of the n-channel device. p-channel device is turned on and the n-channel device is turned off.
The source terminal of the p-channel device is at VDD
The source terminal of the n-channel device is at ground.
0 1
![Page 38: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/38.jpg)
10-8 Complementary MOS (CMOS)
Inverter
2. When the input is high, both gates are at VDD. The p-channel device is turned off and the n-channel device is turned on.
1 0
![Page 39: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/39.jpg)
10-8 Complementary MOS (CMOS)
NAND Gate
1
0
1
A two-input NAND gate consists of two p-type units in parallel and two n-type units in serial.
If all inputs are high, both p-channel transistors turn off and both n-channel transistors turn on. The output produces a low state.
![Page 40: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/40.jpg)
10-8 Complementary MOS (CMOS)
NAND Gate
1
1
0
If any input is low, the associated n-channel transistor is turned off and the associated p-channel transistor is turned on. The output goes to the high state.
![Page 41: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/41.jpg)
10-8 Complementary MOS (CMOS)
NOR Gate
0
10
A two-input NOR gate consists of two n-type units in parallel and two p-type units in serial.
If all inputs are low, both p-channel transistors turn on and both n-channel transistors turn off. The output goes to the high state.
![Page 42: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/42.jpg)
10-8 Complementary MOS (CMOS)
NOR Gate
1
00
If any input is high, the associated p-channel transistor is turned off and the associated n-channel transistor is turned on. The output goes to the low state.
![Page 43: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/43.jpg)
10-8 Complementary MOS (CMOS)
COMS Characteristics
•Low power dissipation
•Greater packing density
•Good noise immunity
•Reasonable propagation delay
![Page 44: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/44.jpg)
10-9 CMOS Transmission Gate Circuits
A transmission gate consists of one n-channel and one p-channel MOS transistor connected in parallel.
When the N gate is at ground and P gate at VDD, both transistors are off and there is an open circuit between X and Y.
0
1
![Page 45: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/45.jpg)
10-9 CMOS Transmission Gate Circuits
When the N gate is at VDD and P gate at ground, both transistors are on and there is an close circuit between X and Y.
1
0
The block diagram of the transmission gate
![Page 46: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/46.jpg)
10-9 CMOS Transmission Gate Circuits
The transmission gate is usually connected to an inverter and referred to as a bilateral switch.
•When C=1, the switch is closed;
•when C=0, the switch is open.
![Page 47: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/47.jpg)
10-9 CMOS Transmission Gate Circuits
Exclusive-OR Constructed with Transmission Gates
The block diagram of Exclusive-OR Constructed with Transmission Gates
The truth table of Exclusive-OR Constructed with Transmission Gates
![Page 48: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/48.jpg)
10-9 CMOS Transmission Gate Circuits
Multiplexer with Transmission Gates
0
0
![Page 49: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/49.jpg)
10-9 CMOS Transmission Gate Circuits
Gated D Latch with Transmission Gates
1
Q=D
![Page 50: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/50.jpg)
10-9 CMOS Transmission Gate Circuits
Gated D Latch with Transmission Gates
0
Q retains its present state.
![Page 51: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/51.jpg)
10-10 Switch-Level Modeling with HDL
//CMOS inverter Fig. 10-22 (a)module inverter (Y,A); input A; output Y; supply1 PWR; supply0 GRD; pmos (Y,PWR,A); //(Drain,source,gate) nmos (Y,GRD,A); //(Drain,source,gate)endmodule
Define the power and
ground with the keywords
supply1 and supply0
Inverter
![Page 52: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/52.jpg)
10-10 Switch-Level Modeling with HDL
//CMOS inverter Fig. 10-22 (a)module inverter (Y,A); input A; output Y; supply1 PWR; supply0 GRD; pmos (Y,PWR,A); //(Drain,source,gate) nmos (Y,GRD,A); //(Drain,source,gate)endmodule
Instantiate a PMOS and a
NMOS
Inverter
![Page 53: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/53.jpg)
10-10 Switch-Level Modeling with HDL
//CMOS inverter Fig. 10-22 (a)module inverter (Y,A); input A; output Y; supply1 PWR; supply0 GRD; pmos (Y,PWR,A); //(Drain,source,gate) nmos (Y,GRD,A); //(Drain,source,gate)endmodule
The output and the input are common to both transistors at their drain and gate terminals, respectively.
Inverter
![Page 54: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/54.jpg)
10-10 Switch-Level Modeling with HDL
//CMOS 2-input NAND Fig. 10-22(b)module NAND2 (Y,A,B); input A,B; output Y; supply1 PWR; supply0 GRD; wire W1; //terminal between two nmos pmos (Y,PWR,A); //source connected to Vdd pmos (Y,PWR,B); // parallel connection nmos (Y,W1,A); // serial connection nmos (W1,GRD,B); // source connected to groundendmodule
Two PMOS transistors connected in parallel with their source terminal connected to PWR.
NAND Gate
![Page 55: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/55.jpg)
10-10 Switch-Level Modeling with HDL
//CMOS 2-input NAND Fig. 10-22(b)module NAND2 (Y,A,B); input A,B; output Y; supply1 PWR; supply0 GRD; wire W1; //terminal between two nmos pmos (Y,PWR,A); //source connected to Vdd pmos (Y,PWR,B); // parallel connection nmos (Y,W1,A); // serial connection nmos (W1,GRD,B); // source connected to groundendmodule
Two NMOS transistors connected in serial with a common terminal W1.
NAND Gate
![Page 56: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/56.jpg)
10-10 Switch-Level Modeling with HDL
//XOR with CMOS switchs Fig. 10-25module SXOR (A,B,Y); input A,B; output Y; wire Anot, Bnot;//instantiate inverter inverter v1 (Anot,A); inverter v2 (Bnot,B);//instantiate cmos switch cmos (Y,B,Anot,A); //(output,input,ncontrol,pcontrol) cmos (Y,Bnot,A,Anot);endmodule
Transmission gate description
Circuits with Transmission Gate
![Page 57: Chapter 10 Digital Integrated Circuits 10-1 Introduction Introduction 10-2 Special Characteristics Special CharacteristicsSpecial Characteristics 10-3](https://reader035.vdocuments.site/reader035/viewer/2022081501/56649e0f5503460f94af91e0/html5/thumbnails/57.jpg)
10-10 Switch-Level Modeling with HDL
//CMOS inverter Fig. 10-22(a)module inverter (Y,A); input A; output Y; supply1 PWR; supply0 GRD; pmos (Y,PWR,A); //(Drain,source,gate) nmos (Y,GRD,A); //(Drain,source,gate)endmodule//Stimulus to test SXORmodule test_SXOR; reg A,B; wire Y;
Continued //Instantiate SXOR SXOR X1 (A,B,Y);//Apply truth table initial begin A=1'b0; B=1'b0; #5 A=1'b0; B=1'b1; #5 A=1'b1; B=1'b0; #5 A=1'b1; B=1'b1; end//display results initial $monitor ("A =%b B= %b Y =%b",A,B,Y);endmodule