chapter 1 introduction of fatek fbs series · pdf filechapter 1 introduction of fatek fbs...
TRANSCRIPT
Luis Mara Drago 1951 Of. 13 - Parque Industrial Burzaco - Buenos Aires - ArgentinaTel.: 5235-9383 /4327-2471 - www.altusarg.com.ar - [email protected]
Chapter 1 Introduction of FATEK FBS Series PLC The FATEK FBS Series PLC is a new generation of micro PLC equipped with excellent functions comparable to medium
or large PLC, with up to five communication ports. The maximum I/O numbers are 256 points for Digital Input (DI) and Digital Output (DO), 64 words for Numeric Input (NI) and Numeric Output (NO). The Main Units of FBS are available in three types: MA (Economy Type), MC (High-Performance Type), and MN (High-Speed NC Type). With the combination of I/O point ranges from 10 to 60, a total of 17 models are available. Fifteen DI/DO and 19 NI/NO models are available for Expansion Units/Modules. With interface options in RS232, RS485, USB, Ethernet, CANopen, Zigbee and GSM, the communication peripherals are available with 15 boards and modules.
1.1 Appearance of Main Unit
All the Main Units of FBS-PLC have the same physical structure. The only difference is the case width. There are four different case sizes, which are 60mm, 90mm, 130mm, and 175mm. The figure below will use the Main Unit case of the FBS-24MC as an example for illustration:
( )OUT Y
Y6Y1AC100~240V
C0 Y0Y4Y2
C2 Y3
PORT0
Y5C4 C6
048
2I65
9
Y8Y7 Y9
37
( )IN X
X8X0
PROGRAMMABLECONTROLLER
24V OUTS/S
RXTX
RUNERR
I2 I3
POW
X4X2X1 X3
0
84
2I
I0965
X6X5 X7
X12
3
I I7
X10X9 X11 X13
X10
3I 20
Y2AC100~240V
C0Y1
Y0 C2
8
Y4Y3 C4
Y5 Y6C6 Y7
95 64 7
X2
TX
24V OUTS/S
X0X1
IN X( )
RX
ERR
OUT Y( )
POWRUN
0
X3 X5X4
X7X6
X9X8
Y8Y9
X12X11 X13
3
1
4
116
12
9 16 15 18 20
191510 1735 2
8
7
( ) ( )
984 5
I
I2 I3I II0
6 732
max.400mA
IN
400mAmax.
INFBs-24MCR2-AC FBs-24MCR2-AC
13
14
X9
Y7
PORT1
Y0
PORT2
AC100~240V
C0
24V OUT
RX
TX
RX
S/S
TX
RX
Y4
PORT0
C2Y1
Y3Y2
CONTROLLER
TX
65 749
C4Y5
8
C6Y6
POW
ERR
I
RUN
0( )OUT Y
2 3
PROGRAMMABLE
X4X0X1 X3
X2
I3
I59
4
I28
X5
0
X6
76
IN X( )
I0 I I
X8
2
X7
3
Y9Y8
X12X10X11 X13400mA
max.
INFBs-24MCR2-AC
1 35mm-width DIN RAIL 2 DIN RAIL tab 3 Hole for screw fixation (4.5 2) 4 Terminals of 24VDC power input and digital input (Pitch 7.62mm) 5 Terminals of main power input and digital output (Pitch 7.62mm) 6 Standard cover plate (without communication
board) 7 Cover plate of built-in communication port (Port 0)
(Front view without Communication Board) (Front view with cover plate removed)
(Front view with CB-22 Board installed)
H1-2
Output expansion slot
Digital output terminal block and Main power input (for XY- )
Screw hole4.5 2
Expansion cable connector
Y9
DIN RAIL tab
C3C1 Y1Y2
CONTROLLERPROGRAMMABLE
765 8
Y3Y4
Y5C5
Y7Y6C7
I09
Y8
OUT Y2I 3 4
( )
POW
Output status indicator
Y10
X11
Digital input terminal block
X124V INS/S X2
X7 X9X5X3
I3
X4 X6
6 75 8
IN XI4I09 I I
( )
I2
2I 3
X8
4
X10X13
X12 X14
Input status indicator
FBs-24XYR
Output expansion slot cover plate
Front view of output expansion slot with cover plate removed
8 Indicators for transmit (TX) and receive (RX) status of built-in communication port (Port0). 9 Indicator for Digital Input (Xn). 10 Indicator for Digital Output (Yn). 11 Indicator for system status (POW, RUN, ERR). 12 I/O output expansion header cover [units of 20 points or beyond only], with esthetic purpose and capable of securing
expansion cable.
13 FBS-CB22 Communication Board (CB). 14 FBS-CB22 CB cover plate (each CB has its own specific cover plate) 15 Screw holes of communication board. 16 Connector for communication board (for 7 types CB of CB2, CB22, CB5, CB55, CB25, CBE, CBCAN , 3 types AIO
of B2DA, B2AD, B4AD, and 2 types DAP of BDAP and BPEP)
17 Left side (communication) expansion header (only available in MC/MN model, for CM22, CM25, CM55, CM25E, CM55E, and CMGSM connection).
18 Connector for Memory Pack. 19 Connector for built-in communication port (Port 0) (With USB and RS232 optional, shown in the figure is for RS232) 20 Right side (I/O) output expansion header (only available in units with 20 points or beyond), for connecting with
cables from expansion units/modules.
1.2 Appearance of Expansion Unit/Module
There are three types of cases for expansion units/modules. One type uses the same case as main unit that of the 90mm,
130mm, and 175mm, while the other two have thinner 40mm and 60mm cases, which are for expansion modules. All
expansion cables (left) of expansion units/modules are flat ribbon cables (5cm long), which were soldered directly on the PCB,
and the expansion header (right) is a 14Pin Header, with this to connect the right adjacent expansion units/modules. In the
following, each of the three types of expansion units/modules is described as an example:
Expansion unit/module with 90mm, 130mm, or 175mm width case: [ -24XY, -40XY, -60XY, -16TC, -16RTD]
H1-3
Expansion unit/module with 60mm width case: [-16XY, -16Y, -20X ]
Expansion cable connector DIN RAIL tabI/O terminal block
Screw hole4.5 2
Output expansion slot
Output status indicator
83
C1Y1
Y2Y3
C3Y4
POW
6 72I
Y8Y6Y5
C5Y7
( )OUT Y4 5
83
I/O terminal block
S/S
2I76
X1X2
X3X8
54
( )IN X
X6X4X5 X7
Output expansion slot
Front view of output expansion slot with cover plate removed
FBs-16XYR
Output expansion slot cover plate
Expansion module with 40mm width case: [ -8XY, -8Y, -8X, -6AD, -2DA, -4DA, -4A2D, -2A4TC,
-2A4RTD,-7SG1, -7SG2, -2TC, -6TC, -6RTD, -CM5H, -6NTC, -4PT,
-1LC, -1HLC, -VOM ]
Screw hole4.5 2
Expansion cable connector
Output status indicator
Input status indicator
DIN RAIL tabI/O terminal block
POWOUT Y
C1Y1
I 2
Y3C3
Y2Y4
( )
43
X2
2I
S/S X1X4
43( )IN X
X3
I/O terminal block
Front view of output expansion slot with cover plate removed
FBs-8XYR
Output expansion slot cover plate
Output expansion slot
H1-4
DIN RAIL tab
Screw hole4.5 2
Expansion cable connector
Input status indicator
X8 FG
I/O Header socket
X24
X16S/S3
X22X20X18
X10S/S2
X14X12
FG
FG
X19X21X23
X17
X13X15
X9X11
S/S1
X6X4X2
20I8 I9I7POW
I02
9I
II I23 4
X1
X5X7
X3
23 24222IIN X( )
I5I4I365 7
I68
FBs-24X
Output expansion slot cover plate
Front view of output expansion slot with cover plate
Output expansion slot
Expansion module with 40mm width case: [ -24X, -24YT, -24YJ, -32DGI ]
1.3 Appearance of Communication Expansion Module
The Communication Module (CM) of FBS-PLC has a 25mm-width case, which can be used in the following seven modules: -CM22, -CM25, -CM55, -CM25E, -CM55E, -CM25C, -CM5R.
4.5 2
( )
Port3
Port4
Port3
Port4
17
DIN RAIL
FBs-CM25E
PORT3 (RS232)
RX
TX
NT
TX
TX
RX
RX
RUN
LNK
(Port4)
Terminator (T:ON, N:OFF)
G
6
2
1
+
3ETHERNETPORT4 (RS485)
Port 3 Communication
Screw hole 4.52
Port3 Communication
Port 4 Communication Socket
Port4 Communication indicator
Terminator Switch (T: ON, N:OFF)
DIN RAIL tab
Communication module expansion cableconnector (to be plugged in main unit 17 )
Ethernet network (Port 4)
H1-5
1.4 List of FBs-PLC Models
Module Name Specifications
Main U
nits
Basic Main Units
FBs-10MAC 6 points 24VDC digital input (2 points high speed 100KHz, 2 points medium speed 20KHz, 2 points medium speed total 5KHz); 4 points relay or transistor output (2 points high speed 100KHz, 2 points medium speed 20KHz); 1 RS232 or USB port(expandable up to 3); I/O is not expandable
FBs-14MAC 8 points 24VDC digital input (2 points high speed 100KHz, 2 points medium speed 20KHz, 4 points medium speed total 5KHz); 6 points relay or transistor output (2 point high speed 100KHz, 4 points medium speed 20KHz); 1 RS232 or USB port(expandable up to 3); I/O is not expandable
FBs-20MAC 12 points 24VDC digital input (2 points high speed 100KHz, 4 points medium speed 20KHz, 6 points medium speed total 5KHz); 8 points relay or transistor output (2 points high speed 100KHz, 6 points medium speed 20KHz); 1 RS232 or USB port(expandable up to 3)
FBs-24MAC 14 points 24VDC digital input (2 points high speed 100KHz, 6 points medium speed 20KHz, 6 points medium