chandler low profile - fairbank equipment

QUALITY TENDERS AND SPREADERS

Gainesville, Georgia 30503 • (770) 536-8891Toll Free 800-243-3319 • Fax (770) 535-1265

www.chandlerequipment.net

CHANDLER LOW PROFILEORCHARD AND GROVE PULL-TYPEFERTILIZER AND LIME SPREADER

Spreader Dimensions

• Overall length 197″ (16′ 5″)

• Overall width 80.5″ (6′ 81//2″)

• Overall height 64″ (5′ 4″)

• Tire Size 16.5L X 16.1(Above dimensions will vary with size of tire )

Hopper Specifications• 3-Ton Capacity (Fertilizer)

• 5-Ton Capacity (Lime)

Available In:

304 Stainless Steel Hopper (shown)409 Stainless Steel

• Also available with multipleoptions as listed on back of brochure.

The Chandler Low Profile Orchard and Grove Pull-Type Spreader is durable, heavy-duty and well designedfor long-lasting, trouble-free service. The low profile design of this spreader allows for ease of travel betweenrows without damage to trees. The banding attachment around spinners allows fertilizer to be properly placedaround trees. Remove Banding Attachment and spreader can be used for standard application of fertilizer andlime. All Chandler Spreaders have been quality checked and tested to provide the best possible spreadpattern for your requirements.

(Unit Shown W/PTO Drive Spinners)




HOPPER SPECSHopper Construction: 3-Ton (93 Cubic Feet—Water Level)Hopper Length: 10 feet (120″)Hopper Width: 5 feet (60″)Hopper Depth: 38 inches

HOPPER CONSTRUCTIONRails: 3/16″ 304 Stainless Steel Plate Floor: 10 ga. 304 Stainless Steel

Sides: 12 ga. 304 Stainless Steel Front End: 12 ga. 304 Stainless Steel

Rear End: 10 ga. 304 Stainless Steel

FRAME AND SUSPENSIONAxle: Single axle, rigid mounted s/12,000# (per pair) spindles and hubs with 8 bolt on 8″ circleTires and Wheels: 19L x 16.1 - 10 ply Good Year Tires mounted on 16C x 16.1 Duty WheelsTongue and Hitch: Tongue channels manufactured of 8″x11.5# structural channel with heavy duty adjustable pin type hitchJack: 7,000# Drop tube-side wind screw jackCrop Clearance: 14.5″ Axle Clearance

CONVEYOR SPECSConveyor Type: 16″-wide 1″ x 1″ mesh type heavy-duty type 304 stainless steel conveyor chain

or optional dual 8″-wide 1″ x 1″ mesh typeConveyor Drive: Conveyor is driven by press wheel, engaged by hydraulic cylinder.Conveyor Rollers: Front and rear rollers manufactured from ASTM-36 plate steelMetering Gate: Double Rack and Pinion operated—metering gate, gate slides, and gate turn pipes

manufactured from type 304 stainless steel.Material Divider: Specially engineered “Screw Type” adjustable material divider for proper material placement on

spinners to ensure uniform spread pattern at all application rates (screw rod and material divider manufactured of type 304 stainless steel).

SPINNER SPECSSpinner Design: Twin “Dished Type” spinners, 24″ diameter with 6 blades per spinner.Spinner Drive: PTO driven spinners, with optional hydraulic—plug to tractor or Self Contained Hydraulic System.




CHANDLER MODEL 10PTT-FTTANDEM AXLE PULL-TYPE

FERTILIZER/LIME SPREADERSpreader Dimensions


• Overall width 96″ (8′ 0″)


• Tire Size 14Lx16.1(Above dimensions will vary with size of tire)

Full ground wheel drive available

Hopper Specifications

• Length 120″ (10′ 0″)

• Width 96″ (8′ 0″)

• Height 51.5″ (4′ 3″)

• Net depth 44.75″ (3′ 9″)

• Capacity 185 cu. ft.(6 ton capacity)


The Chandler Pull-Type Fertilizer Spreader is durable, heavy-duty and well designed for long-lasting, trouble-free service. The design and construction quality of this spreader sets the standard in the agri-businessindustry. This unit is offered in corrosive-resistant 304 stainless steel. This pull-type spreader has been qualitychecked and tested to provide the best possible spread pattern for your requirements.




HOPPER SPECSHopper Construction: (A) 304 Stainless Steel

(B) 409 Stainless Steel(C) Carbon Steel with Stainless Steel at critical corrosion points

Angle of Sides: Standard 45°, Optional 52°52° is used in heavy lime application

FRAME & SUSPENSIONAxle: Tandem Axle, Henschen suspension spindles & hubs with 6 bolts.Tires and Wheels: 14L x 16.1—10-ply tires mounted on W11C x 16.1 heavy-duty wheels.Optional: Tongue channels mfg. of 7″ x 9.8# structural channel with heavy-duty adjustable pin type hitch.

CONVEYOR SPECSConveyor Type: 1″ x 1″ mesh type heavy-duty type 304 stainless steel conveyor chain—16″ wide. (Also available in

18″, 20″& 24″) (Bar style chains and neoprene belts of various widths also available on special order.)Conveyor Drive: Conveyor is driven by press wheel, engaged and disengaged with hydraulic cylinder connected to tractor.Conveyor Rates: Utilize two sets of sprockets—low to medium and medium to high—application rate from 75 lbs. to

4,500 lbs. per acre.Conveyor Rollers: Front and rear rollers manufactured from ASTM-35 plate steel (most competitors use cast iron).Metering Gate: Double Rack and Pinion operated—metering gate, gate slides, and gate turn pipe


spinners to insure uniform spread pattern at all application rates. (Screw rod and material divider manufactured of type 304 stainless steel.

SPINNER SPECSSpinner Design: Twin “Dished Type” spinners, 24″ diameter with 6 blades per spinner, specially designed

for extremely accurate broadcasting of materials.Spinner Drive: PTO Drive with gear cases, hydraulic drive spinners with hook-up to tractor—or self-contained

hydraulic system driven from tractor PTO.




CHANDLER MODEL 20 PTT-FTTANDEM AXLE PULL-TYPE

LIME AND FERTILIZER SPREADER

Spreader Dimensions




• Tire Size 16.5L X 16.1(Above dimensions will vary with size of tire )

Hopper Specifications• Length 120″ (10′ 0″)

• Width 96″ (8′ 0″)

• Height 64″ (5′ 4″)

• Net depth 57″ (4′ 9″)







HOPPER SPECSHopper Construction: (A) 304 Stainless Steel

(B) 409 Stainless Steel(C) Carbon Steel with Stainless Steel at critical corrosion points

Angle of Sides: Standard 45°, Optional 52°52° is used in heavy lime application

SUSPENSIONAxle: Tandem Axle Henschen Suspension—20,000# per pairAxle Clearance: 21″Tires and Wheels: 16.5L x 16.1 Tires on W14C x 16.1 WheelsOptional: 19L Tires on W16C x 16.1 Wheels

CONVEYOR SPECSConveyor Type: 1″ x 1″ mesh type heavy-duty type 304 stainless steel conveyor chain—16″ wide. (Also available in

18″, 20″& 24″) (Bar style chains and neoprene belts of various widths also available on special order.)Conveyor Drive: Conveyor is driven by press wheel, engaged and disengaged with hydraulic cylinder connected to tractor.Conveyor Rates: Utilize two sets of sprockets—low to medium and medium to high—application rate from 75 lbs. to

4,500 lbs. per acre.Conveyor Rollers: Front and rear rollers manufactured from ASTM-35 plate steel (most competitors use cast iron).Metering Gate: Double Rack and Pinion operated—metering gate, gate slides, and gate turn pipe


spinners to insure uniform spread pattern at all application rates. (Screw rod and material divider manufactured of type 304 stainless steel.

SPINNER SPECSSpinner Design: Twin “Dished Type” spinners, 24″ diameter with 6 blades per spinner specially designed

for extremely accurate broadcasting of materials.Spinner Drive: (A) PTO Shaft and Belts (not recommended for heavy lime application)

(B) Hydraulic Drive with hookup to tractor(C) Self-contained hydraulic driven from tractor PTO

CHANDLER MODEL 9-PT-FTFERTILIZER/LIME SPREADER

The Chandler Fertilizer andLime spreader is a durable,heavy duty and well designedunit to give long lasting, trouble-free service. The designand construction go far beyond present standards and are striving for a lime or fertilizerspreader to meet the quality ourcustomers demand. The superi-or design and construction, itslow initial cost, its efficiency andease of operation and economi-cal maintenance make it thepreferred spreader throughoutthe agri-business industry.

SPREADER AND BULK FEED BODY DIVISION

HANDLER EQUIPMENT CO.Gainesville, Georgia 30503 (770) 536-8891

Toll Free 800-243-3319 • Fax (770) 535-1265

The Chandler “FT” unit is available in (3) models:

(1) “FT-CS”—Standard dutycarbon steel with stainlesssteel at critical corrosionpoints.

(2) “FT-409”—Stainless steelconstruction

(3) “FT-304”—Stainless steelconstruction

“HOPPER SPECS”Hopper Capacity: 4 to 5 Ton Capacity (according to

cu. ft. weight of material).Hopper Net Length: 9 ft. (108 in.)Hopper Width: 8 ft. (96 in.)Hopper Net Depth: 43 in.Hopper Overall Height 6′11″ (83 in.) Also Available in low

profile design making unit have 77″overall height.

Angle of Repose: Side panels @ 45°; End panels @ 22°

“FRAME & SUSPENSION”Axle: Single axle, rigid mounted s/12,000 #(per pair) spindles & hubs with 8 bolt on 8 circle (see optional

equipment—option A.) Adjustable Row Track available.Tires and Wheels: 19L x 16.1—10 ply Good Year tires mounted on 16″ cl 6.1 heavy duty wheels. 11.2 x 28—10 ply for

row crop model.Tongue and Hitch: Tongue channels mfd. of 7″ x 9.8 # structural channel with heavy duty adjustable pin type hitch. (see

optional equipment—option E.) Note: Many competitors use formed steel channels or a lighter weight6″ channel for tongue channels.

Jack: 7000 # drop tube-side wind screw jack.Crop Clearance: 24″, 30″, 40″ Spinner Clearance

“CONVEYOR SPECS”Conveyor Type: 1″ x 1″ mesh type, heavy duty type 304 stainless steel conveyor chain—16″ wide. (Also available in

other widths.) (Bar style chains and neoprene belts of various widths also available on special order.)Conveyor Drive: Conveyor is driven by press wheel, engaged and disengaged with handle located at front of

spreader unit. (Optional hydraulic cylinder available to engage and disengage press wheel from tractor.)

Metering Gate: Double rack and pinion operated. Metering gate, gate slides and gate turn pipe mfd. from type 304stainless steel. Note: Many competitors utilize a screw jack to raise and lower metering gate.

Conveyor Rates: Utilize two sets of sprockets—low to medium and medium to high application rate from 75 lbs. to 4000lbs. per acre. Unit, unlike many competitors models, utilizes same roller chain for both applicationrates and can be changed simply by loosening nut on idler assembly and moving chain.

Material Divider: Specifically engineered “Screw Type” adjustable material divider for proper material placement onspinners to insure uniform spread pattern at all application rates. (Screw rod and material divider mfd.of type 304 stainless steel.)

Conveyor Rollers: Front and rear rollers mfd. from ASTM-36 plate steel. (Most competitors use cast iron.) Front andrear rollers have 11⁄2″″ diameter shafts with 11⁄2″″ flange type bearings.

“SPINNER SPECS”Spinner Design: Twin “Dished Type” spinners, 24″ diameter with 6 blades per spinner specially designed for extreme-

ly accurate broadcasting of materials.Spinner Drive: Press wheel driven with dual “B” section V-Belts. Power transmitted thru extremely heavy duty gear

case w/11⁄4″″ diameter shafts and tapered roller brgs. Utilizes same press wheel that drives conveyor. Optional PTO or Hydraulic Drive.

Manufactured by: Chandler Equipment Company • P.O. Box 2533 • Gainesville, GA 30503 • Phone (770) 536-8891 • Toll Free 800-243-3319



SPREADER AND BULK FEED BODY DIVISION

CHANDLER MODEL 9-PT-FTGROUND WHEEL DRIVE PULL TYPE

FERTILIZER/LIME SPREADER

The Chandler Fertilizer and Lime Spreader is a durable, heavy duty and well designed unit to give long lasting,

trouble-free service. The design and construction goes far beyond present standards and is striving for a lime or

fertilizer spreader to meet the quality our customers demand. The superior design and construction, its low initial cost,

its efficiency and ease of operation and economical maintenance make it the preferred spreader throughout the agri-

business industry. The Chandler “FT” unit is available in (3) models:

(1) “FT-CS” – Standard duty carbon steel with stainless steel at critical corrosion points.

(2) “FT-CH” – Heavy duty carbon steel with stainless steel at critical corrosion points.

(3) “FT-SS” – Stainless steel construction.

“HOPPER SPECS”Hopper Capacity: 4 to 5 Ton Capacity (according to cu. ft. weight of material).

Hopper Net Length: 9 ft. (108 in.)

Hopper Width: 8 ft. (96 in.)

Hopper Net Depth: 43 in.

Hopper Overall Height: 6′11″ (83 in.) Also available in low profile design making unit have 77″ overall height.

(w/19.1x16.1 tires):

Angle of Repose: Side panels @ 45º; End panels @ 22º

“FRAME & SUSPENSION”Axle: Single axle, rigid mounted s/12,000 # (per pair) spindles & hubs with 8 bolt circle (See optional

equipment – option A.)

Tires and Wheels: 19L x 16.1 – 10 ply Good Year tires mounted on 16″ cl 6.1 heavy duty wheels. (See optional equipment– options B, C, & D.)

Tongue and Hitch: Tongue channels mfd. of 7″ x 9.8 # structural channel with heavy duty adjustable pin type hitch. (Seeoptional equipment – option E.) Note: Many competitors use formed steel channels or a lighter weight6″ channel for tongue channels.

Jack: 7000 # drop tube-side wind screw jack. Note: Many competitors use smaller jacks.

“CONVEYOR SPECS”Conveyor Type: 1″ x 1″ mesh type, heavy duty type 304 stainless steel conveyor chain – 16″ wide. (Also available in

other widths.) (Bar style chains and neoprene belts of various widths also available on special order.)

Conveyor Drive: Conveyor is driven by press wheel, engaged and disengaged with handle located at front of spreaderunit. (Optional hydraulic cylinder available to engage and disengage press wheel from tractor.) (Seeoptional equipment – F.)

Metering Gate: Double rack and pinion operated. Metering gate, gate slides and gate turn pipe mfd. from type 304stainless steel. Note: Many competitors utilize a screw jack to raise and lower metering gate. We alsooffer this type gate and mechanism as optional equipment with a reduction in price. (See optionalequipment – option G.)

Conveyor Rates: Utilize two sets of sprockets – low to medium and medium to high application rate 75 lbs. to 4000 lbs.per acre. Unit, unlike many competitors models, utilizes same roller chain for both application ratesand can be changed simply by loosening wing nut on idler assembly and moving chain (no toolrequired.)

Material Divider: Specially engineered “Screw Type” adjustable material divider for proper material placement onspinners to insure uniform spread pattern at all application rates. (Screw rod and material divider mfd.of type 304 stainless steel.)

Conveyor Rollers: Front and rear rollers mfd. from ASTM-36 plate steel. (Most competitors use cast iron.) Front and rearrollers have 11/2″ diameter shafts with 11/2″ flange type bearings. (Many competitors use smallerdiameter shafts, thus smaller bearings.)

“SPINNER SPECS”Spinner Design: Twin “Dished Type” spinners, 24″ diameter with 6 blades per spinner specially designed for extreme

accurate broadcasting of materials.

Spinner Drive: Press wheel driven with dual “B” section V-Belts. Power transmitted thru extremely heavy duty gearcase with 11/4″ diameter shafts and tapered roller brgs. Utilizes same press wheel that drivesconveyor.

Manufactured by: Chandler Equipment Company • P.O. Box 2533 • Gainesville, GA 30503 • (770) 536-8891

NEW



web: applied.net/chandler

NEW CHANDLER PULL-TYPE FERTILIZERSPREADER MODEL PT 10FSS

Spreader Dimensions




• Mounted on 12.5L Tires



• Length 120″ (10′ 0″)

• Width 80″ (6′ 8″)

• Height 55″ (4′ 7″)

• Net depth 45″ (3′ 9″)


• Also available-6 ton

THE CHANDLER PTO MODEL PULL-TYPE FERTILIZER SPREADER





“Frame & Suspension”Axle: Tandem axle, 6500# Henschen suspension with 6 bolt spindles & hubsFrame: Heavy duty 6″ Channel, with heavy duty adjustable hitch and 7000# jack

“Conveyor Specs” Conveyor Type: 1 x 1 heavy-duty type 304 stainless steel conveyor chain—8″ wideConveyor drive: Conveyor is driven by press wheel with laminated tire for long life (Also availablewith Hydraulic cylinder to engage ground wheel)Metering Gate: Double rack and pinion gate, metering gate, gate slides and gate pipe mfg. fromtype 304 stainless steelConveyor rates: Fertilizer rates from 80# to 600# per acreMaterial Divider: Specially engineered “Screw Type” adjustable material divider for proper materialplacement on spinners to insure uniform spread pattern at all application rates (Screw rod andmaterial divider made of type 304 stainless steel)Conveyor Rollers: Front and rear rollers mfg. from ASTM-36 plate steel (Most competitors usecast iron)

“Spinner Specs”Spinner Design: Twin “Dished Type” spinners,24″ diameter with 6 blades per spinner, speciallydesigned for extremely accurate broadcasting ofmaterials.

Spinner Drive: PTO Drive with gear casesunderneath the spinners or overhead belt drivespinners.

55.00




CHANDLER PULL-TYPE FERTILIZERSPREADER MODEL PT 12FSS

Spreader Dimensions


• Overall width 84″ (7′ 0″)• Overall height 91″ (7′ 7″)

(Standard)

• Height varies with tire size

• Mounted on 14L Tires(Standard)



• Length 120″ (10′ 0″)

• Width 80″ (6′ 8″)

• Height 60″ (5′ 0″)

• Net depth 53″ (4′ 5″)


• Also available-5 ton

THE CHANDLER PTO MODEL PULL-TYPE FERTILIZER SPREADER





“Frame & Suspension”Axle: Tandem axle, 6500# Henschen suspension with 6 bolt spindles & hubsFrame: Heavy duty 6″ Channel, with heavy duty adjustable hitch and 7000# jack

“Conveyor Specs” Conveyor Type: 1 x 1 heavy-duty type 304 stainless steel conveyor chain—8″ wideConveyor drive: Conveyor is driven by press wheel with laminated tire for long life (Also availablewith Hydraulic cylinder to engage ground wheel)Metering Gate: Double rack and pinion gate, metering gate, gate slides and gate pipe mfg. fromtype 304 stainless steelConveyor rates: Fertilizer rates from 80# to 600# per acreMaterial Divider: Specially engineered “Screw Type” adjustable material divider for proper materialplacement on spinners to insure uniform spread pattern at all application rates (Screw rod andmaterial divider made of type 304 stainless steel)Conveyor Rollers: Front and rear rollers mfg. from ASTM-36 plate steel (Most competitors usecast iron)

“Spinner Specs”Spinner Design: Twin “Dished Type” spinners,24″ diameter with 6 blades per spinner, speciallydesigned for extremely accurate broadcasting ofmaterials.

Spinner Drive: PTO Drive with gear casesunderneath the spinners or overhead belt drivespinners.

8″ CHAIN

Gainesville, Georgia 30503Toll Free 1-800-243-3319


CHANDLER TRUCK-MOUNTEDFERTILIZER AND LIME SPREADER

(with Spread-Master Technology)Building the most accurateand heaviest built spreader

since 1969.

Application rates from 60pounds per acre on fertilizer toover six tons per acre on lime (depending on chain width).

All Chandler Spreaderscan be equipped with

variable rate controls fromMid-West Technologies.(Mid-Tech Legacy 6000)



Chandler “FT—EXW” HopperAvailable in 10′′, 11′′, 12′′, and 13′′ Lengths

Catwalks 130″″ Wide10′ UNIT 11′ UNIT 12′ UNIT 13′ UNIT

Hopper Capacity 221 Cu. F t . 244 Cu. F t . 266 Cu. F t . 288 Cu. F t .(Struck Level)

Payload (struck level) 14,365 Lbs. 15,860 Lbs. 17,290 Lbs. 18,720 Lbs.(@ 65# Material)

Hopper Capacity 251 Cu. F t . 276 Cu. F t . 301 Cu. F t . 326 Cu. F t .(Heaped and Tarped)

Payload (Heaped) 16,315 Lbs. 17,940 Lbs. 19,565 Lbs. 21,190 Lbs.(@ 65# Material)

Chandler “FT” Hopper

Chandler “FT—LH” Hopper

Available in 11′′, 12′′, 13′′, 14′′ and 15′′ LengthsCatwalks 102″″ Wide

11′ UNIT 12′ UNIT 13′ UNIT 14′ UNIT 15′ UNIT

Hopper Capacity 185 Cu. F t . 202 Cu. F t . 219 Cu. F t . 236 Cu. F t . 254 Cu. F t .(Struck Level)

Payload (struck level) 12,000 Lbs. 13,130 Lbs. 14,235 Lbs. 15,340 Lbs. 16,510 Lbs.(@ 65# Material)

Hopper Capacity 220 Cu. F t . 241 Cu. F t . 261 Cu. F t . 282 Cu. F t . 303 Cu. F t .(Heaped and Tarped)

Payload (Heaped) 14,300 Lbs. 15,665 Lbs. 16,965 Lbs. 18,330 Lbs. 19,700 Lbs.(@ 65# Material)

Available in 11′′, 12′′, 13′′, 14′′ and 15′′ LengthsCatwalks 102″″ Wide

11′ UNIT 12′ UNIT 13′ UNIT 14′ UNIT 15′ UNIT

Hopper Capacity 233 Cu. F t . 255 Cu. F t . 298 Cu. F t . 276 Cu. F t . 320 Cu. F t .(Struck Level)

Payload (struck level) 15,145 Lbs. 16,575 Lbs. 17,940 Lbs. 19,370 bs. 20,800 Lbs.(@ 65# Material)

Hopper Capacity 269 Cu. F t . 295 Cu. F t . 319 Cu. F t . 346 Cu. F t . 370 Cu. F t .(Heaped and Tarped)

Payload (Heaped) 17,485 Lbs. 19,175 Lbs. 20,735 Lbs. 22,490 Lbs. 24,050 Lbs.(@ 65# Material)

All Products and Specifications subject to change without notice.Drawing shown with 45 degree slope sides and 16″″ mesh type chain.

Hopper Construction: Available in three types of material:1. Mild Steel with 304 Stainless Steel at critical corrosion points.2. 409 Stainless Steel (corrosion resistant stainless but has to be painted)3. 304 Stainless Steel (top of the line in spreader manufacturing)Available in 45, 52 or 60 Degree Slope on Sides(Drawings shown with 45 degree slope sides, width will vary depending on degreeof slope)

Conveyor Specs: Available in three types:1. 1″ x 1″ Mesh Type, Heavy Duty Type 304 Stainless Steel—Available in 16″,

18″, 20″, and 24″ Widths.2. Bar Type Chain3. Belt Over—Bar type Chain

Spinner Specifications:1. Twin “Dish Type” Spinners, 24″ diameter with 6 blades per spinner especially

engineered for extremely accurate spread patterns. Mild Steel Construction.Also available in 304 Stainless Steel.

2. High Pressure spinner motors mounted over-head to keep motors out offertilizer and other contaminants for longer life.

3. Material Divider specially engineered “Screw Type” adjustable material dividerfor proper material placement on spinners to insure uniform spread patterns atall application rate and spread widths from 30′–40′ Lime, 50′–60′ Fertilizer withstandard spinner system.

4. Optional: Spread-Master Technology—four-blade configuration spinners and aspecially-designed flow divider for wide swath applications. (60′ Lime—80′Fertilizer)

Chandler Spreader withStandard Spinners

Spread Patterns on Fertilizerfrom 50′′– 60′′ with

Unmatched Accuracy.

Chandler Spreader withSpreader-Master Technology

Spread Patterns onFertilizer up to 90′′, Lime up to 60′′.



CHANDLER FTLH – EXWCHANDLER FTLH – EXWFERFERTILIZER TILIZER AND LIME SPREADERAND LIME SPREADER

• Wider Spread Patterns90′′ Fertilizer60′′ Lime

• Belt-Over Bar Chain orMesh Type Chain

• Dished Type SpinnersDesigned for MaximumCoverage on SpreadPattern

• Designed to Fit AlmostAny Floater Chassis

• Tandem Pump Systemwith 50-GallonHydraulic Oil Tank

The new FTLH-EXW has the same dependability, accuracy and reliability that Chandler Spreaders have beenknown for over the past thirty-eight years with a new cleaner design and wider spread patterns. Our field provendished type spinners with a new four-blade system give the Chandler FTHL-EXW an oval pattern that has beenthe desirable pattern throughout the industry for many years. All Chandler Spreaders are available with Mid-Techor Raven Control systems.

New Cleaner Design, Wider Spread PatternsWith The Same Dependability



Chandler FTLH – EXW HopperSpecifications

11′ Unit 12′ Unit 13′ UnitA – Overall Length 195 1⁄2″ 183 1⁄2″ 195 1⁄2″

B – Inside Hopper 132″ 144″ 156″

Cab to Center of Axle 96″ 102″ 108″

11′ Unit 12′ Unit 13′ UnitHopper Capacity 257 Cu. F t . 280 Cu. F t . 303 Cu. F t .(Struck Level)

Payload (struck level) 16,702 Lbs. 18,220 Lbs. 19,695 Lbs.(@ 65# Material)

Hopper Capacity 287 Cu. F t . 310 Cu. F t . 340 Cu. F t .(Heaped and Tarped)

Payload (Heaped) 18,655 Lbs. 20,150 Lbs. 22,110 Lbs.(@ 65# Material)

Spread Patterns:

Fertilizer up to 90′′Lime up to 60′′

All Products and Specifications subject to change withoutnotice. Drawing shown with 45 degree slope sides and 24″″Belt Over Bar Chain.

Hopper Construction:Available in three types of material: Mild Steel, 409 StainlessSteel, 304 Stainless SteelConveyor Specifications:Available in three types: 24″ – 1″ x 1″ Mesh Type-304 StainlessSteel, Bar Type Chain and Belt Over – Bar Type ChainSpinner Specifications:Four blade configuration spinners and a specially designedflow divider for wide swath applications. (60′ Lime – 90′Fertilizer)High Pressure, Double Bearing spinner motors mountedoverhead keeps motors out of fertilizer and other contaminantsfor longer life.

chandler low profile - fairbank equipment

Documents