ceramic counter-top unit instruction manual
DESCRIPTION
Ceramic Counter-Top Unit Instruction ManualTRANSCRIPT
Base Assembly Unit
Crock
Cover
DispenserFaucet
Float/FillAssembly
Release
FaucetLines
DrainValve
Filter / MembraneUse Indicator
FaucetConnector
O-RingFaucet Adapter
Collar
Washer, remove if faucethas external threads
BASE ASSEMBLY & CROCK TOGETHER
5. Place the crock andassembled dispenserfaucet into the baseassembly unit
6. Wipe the 0-ring of the float fillassembly to be sure that it isclean. Push in the releasebutton on the rear deck of theunit body and insert thefloat fill assembly
FLOAT/FILL ASSEMBLY
10. Replace the aerator with the faucet adaptor provided, it has bothmale and female threads. Tighten the faucet adapter to the faucet
taking care not to mar thepolished surface. Pull the collarof the faucet connector assemblyback, slip on to the faucet adaptorand turn on the cold water(never use hot water) After afew moments the water willbegin to enter the container
11. The flow should be 1 to 1-1/2gallons in 15 minutes, Discard the first 4 gallons as there will be a strong magnesium taste this will dissipate. The crock will fill and the float will rise. When the float is in the full up positionit will stop the flow into the crock.
12. Indicator light blinks green during normal operationIndicator light blinks yellow when 20% filter life remains Indicator light blinks red when it is time to replace the filters.
COUNTER TOP R.O. FILTER REPLACEMENT PROCEDURE
1. Turn off the faucet water supply to the unit.2. Disconnect the unit from the faucet.3. Empty the crock by opening the crock faucet4. Remove the clear cover from the crock5. Remove the crock fill spout by depressing the small lever where the spout is
connected to the white base of the unit. Pull the spout and the float valve thatis attached to it straight up until the float clears the opening of the crock.
6. Remove the crock from the white system base.7. Place the base assembly on a flat surface that is at least twice the size of the base.
There will be some water that will drain from the unit as you replace cartridges so working in an area where water damage will not be a problem or placing the unit on towels is important.
COUNTER TOP R.O. FILTER REPLACEMENT PROCEDURE
8. Remove the four (4) screws on the sides of the unit.9. Lift the unit straight up – the weight of the filters will cause the inner base with
the filters to remain on the flat surface and the outer shell can then be set to theside adjacent to the inner base.
10. Refer to the drawing in your instructions titledCERAMIC COUNTER TOP FILTER IDENTITY
11. Remove the filter(s) that you wish to replace by pushing in the collar on thefittings on each end while simultaneously pulling on the tubes as shown on the following drawing.
COUNTER TOP R.O. FILTER REPLACEMENT PROCEDURE
12. Replace the filter(s) with the new filter(s) taking note of the flow direction marked on the replacement. Replacements are provided with new fittings. To replace the tubes, simply push the tube into the fitting until it hits an internal stop and will move no further. See the following drawing.
13. Re-assemble the system by reversing the above steps.
for further support please contact us at
COUNTER TOP R.O. FILTER REPLACEMENT PROCEDURE
Q: How ofter do you change the filters.A: The easiest way to go about this isn’t time,
but how often you change the 5 micron and KDF filters.example:
5 micron/KDF: Every change (1000 gallons)Dual DI: Every 2nd change (2000 Gallons)RO Membrane: Every 4th change (4000 gallons)Magnesium: Every 4th change (4000 gallons)Post Carbon: Every 4th change (4000 gallons)
Q: How do I know how many gallons I have gone through.A: Your Filter Monitor will tell you
As with all appliances, do not leave unattended!