centralized lubrication
TRANSCRIPT
Centralized Lubrication
CIRVAL S.A.
Pte. Roca 4145 / S2001KDK - Rosario / Santa Fe / Argentine RepublicTel.: 00-54-341-4655777 (Rotative Lines) Fax: 00-54-341-4658810
E-mail: [email protected] / Web site: www.cirval.com
I N D E X
DUALINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE.
DistributorsModel DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DL-01Model DDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DL-02Model DCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DL-03Control ValvesModel VCI-R1000 Pressure Operated Reversing Valve . . . . . . . . . . DL-04Model VCI-R40 Pressure Operated Reversing Valve . . . . . . . . . . DL-05Model VCI-R10 Solenoid Operated Reversing Valve . . . . . . . . . . DL-06Model VCI-R20 Pressure Operated Reversing Valve . . . . . . . . . . DL-07Model VCAP-3 High Pressure Control Valve . . . . . . . . . . . . . . . . DL-08Model VCA-F Relief Valve with strainer . . . . . . . . . . . . . . . . . . . DL-09Model VCC Air Operated Line Isolating Valve . . . . . . . . . . . . DL-10Model CU-693-2 Oil Flow Switch . . . . . . . . . . . . . . . . . . . . . . . . . . DL-11Model CU-986 Oil Flow Control Valve . . . . . . . . . . . . . . . . . . . . . DL-12
SINGLE LINE PROGRESSIVE
Distribution Valves Model MJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLP-01Model MR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLP-02Model MX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLP-03Model C-2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLP-04Model MU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLP-05Model MD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLP-06Model MG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SLP-07
SINGLE LINE PARALLEL
Model CFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL-01Model CSKN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL-02Model CUL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL-03Model CVCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL-04Model CLS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL-05Model CLS11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL-06Model CVA 850 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL-07
CENTRAL PUMPING STATIONS
BCE-DJ4 and BCE-DJ5 Pump Sub-Assembly . . . . . . . . . . . . . . . . . BC-01Model ECB-DC-42 Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-02BCE-DJ25 Pump Sub-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-03
VERSION: 2 Date: 02/08/2007
Version
222.222222222
.
.2222222
.
.2222222..
222
Date
30/06/0430/06/0430/06/04
.30/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/04
.
.30/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/04
.
.30/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/04
.
.
30/06/0430/06/0430/06/04
APPROVED:Federico Rolt
PREPARED:Fernando Díaz
Model ECB-DC-25 Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-04BCE-DJ10 Pump Sub-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-05Model ECB-DC-10 Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-06Model BCM-A1-A/B Manual Pump . . . . . . . . . . . . . . . . . . . . . . . . . BC-07BCMSL Manual Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-08BCN/BCH Pneumatic / Hydraulic Operated Pump . . . . . . . . . . . . . . BC-09ECB-AC/CT-TP Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-10ECB-AC/CT-P/N Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-11ECB-AC-3 Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-12BCE-JR Pump Sub-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-13BCE-JE Pump Sub-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-14BCE-JE/JR-3 Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-15BCE-JE/JR-15/25 Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-16ECB-JE-LS Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-17ECB-EM Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-18ECB-EF Pump Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-19EBC-VA Pumping Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-20Model BCN-219/221 Pneumatic Operated Pump . . . . . . . . . . . . . . . BC-21Model BCN 85 Pneumatic Operated Pump . . . . . . . . . . . . . . . . . . . BC-22Pneumatic Operated Booster Pump . . . . . . . . . . . . . . . . . . . . . . . . . BC-23BCE CV Pump with adjustable discharge . . . . . . . . . . . . . . . . . . . . BC-24Cable Lubricator LCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BC-25
ACCESSORIES
Connector CU-81/CU-83......Union CU-84 . . . . . . . . . . . . . . . . . . . . A-01Elbow CU-87/CU-1103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-02Elbow CU-1104.....CU-1105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-03Reducing Bush CU-104......Nipple CU-151....Serie CU-431 . . . . . . . A-04Plugs CU-86/CU-119/CU-2986 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-05Anchor Block CU-1927.... Bleed Screw PC.... TE Serie CU-137 . . A-06Connection Block CU-1008/CU-1080-B1 . . . . . . . . . . . . . . . . . . . . . A-07Relief Valves CU-962-B / CU-1975-B1 / CU-1997-B1 . . . . . . . . . . . . . . . . . . A-08Check Valves CU-1987-A1/CU-887-D2/CU-1087-B2/CU-2087-B . . . . A-09Rotating Connectors CU-990/CU-989-T/CU-994 . . . . . . . . . . . . . . . A-10Point Applicators PGC-1.....Brushes CLC-C/CLC-P . . . . . . . . . . . . . A-11Filters TF-0/TF-1/TF11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12Filters TF-2/FCSL-3/8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-13Tube Clips CU-301/CU-1301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14One Way Couplings CU-967/CU-968/CU-969 . . . . . . . . . . . . . . . . . A-15Spray Valve VCCS-S1/VCCS-S1-I...Block CSMP...Nozzle CU-992-C . . A-16
TUBES VARIOUSSPECIAL Products THE COMPANY
PREPARED:Fernando Díaz VERSION: 2 DATE: 02/08/2007
2222222222222222222222
.
2222222222222222
30/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/04
.
30/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/0430/06/04
APPROVED:Federico Rolt
Dualine
DL-01
Oil or grease up to NLGI 2 grade.
Máx.: 250 bar - Mín.: 15 barMáx.: 80 ºC - Mín.: 0 ºCAdjustable (See model in the table below)
DescriptionDC valves operate completely hydraulically and can be used either withgrease or oil dual line systems.In these valves, each section can lubricate only one point. Available with 1to 4 outlets. One important feature of these valves is the absence of reten-tion valves and that they have only one moving part, giving a very positivefunctioning and facilities to regulate the flow.
Specifications
Lubricant
Work pressureTemperatureDischarge
MODELDC-130 DC-140
A
28,531,836,646
ModelDC-131
DC-132-133-134DC-141-142-143-144DC-151-152-153-154
DC-161-162
B8,28,28,2
10,210,5
C10,536,510,710,510,5
D45
485462
E
738090
108
F
102111,5127
G
130143,
4163
J2828303337
K3838404457
L4141
55,555,556
M27,729,238,237,241
P100,5100,5120138
152,5
R24,523
27,53032
S39
40,548,55258
T24
273341
V
596987
W
2990,5106
Z
57122142
DC-150 DC-1600,40 1,10 2,40 5,902,40 4,40 10,00 25,00
DC-162-10110,8050,00
Flow regulation per outlet (cm3)Requirement code
Regulation
MIN.MAX.
Model30405060
DC 1
3456
One salidaTwo salidas
Three salidasFour salidas
Nº outlet1234
Dualine Dualine ValvesDC Series
Order examples: DC-131
DC-131DC-141DC-151DC-161
DC-132DC-142DC-152DC-162DC-162-101*
DC 162-101 distributors are available with internal perforation unifying both discharges inonly one, duplicating the flow of the last one.
DC-133DC-143DC-153
DC-134DC-144DC-154
DL-02
Oil or grease up to NGLI 2 grade
Máx.: 250 bar - Mín.: 15 barMáx.: 80 ºC - Mín.: 0 ºCAdjustable (See model in the table below)
DDC valves operate completely hydraulically and can be used either with grease oroil dual line systems.The dosage valve can feed 1 or 2 points of lubrication. Available with 2,4,6 or 8 out-lets. Nevertheless, through a simple method, the discharge can be unified, converting the dual outlet of a valve in a simple one (through a cross porting) duplicating in this way also the capacity of discharge of the dosimeter.One important feature of these valves is the absence of retention valve and thatthey have two moving parts, giving a very positive functioning and facilities to regu-late the flow.
Lubricant
Work pressureTemperatureDischarge
DDC-222DDC-232DDC-242DDC-252
DDC-224DDC-234DDC-244DDC-254
DDC-226DDC-236DDC-246DDC-256
DDC-228DDC-238DDC-248DDC-258
MODEL (double outlet)DDC-220 DDC-230 DDC-240 DDC-250
0,09 0,20 0,50 0,600,60 1,20 2,20 5,00
Regulation
MIN.MAX.
MODEL (single outlet)0,18 0,40 1,00 1,201,20 2,40 4,40 10,00
MIN.MAX.
Model20304050
2345
two outletfour outletsix outlet
eight outlet
Nº outlet2468
Flow regulation per outlet (cm3)
Description
Specifications
Requirement code
Dualine ValvesDDC Series
Dualine
DDC 2
Example Order: DDC-234
C14,3
15,6
A14,3
31,8
D28,6
44
E42,9
76
I27,8374456
J38,1
57
F57,2
108
G71,4
140
K26,9
41
L15,9
30
M6,35
7
N30,2
62
O44,5
94
P58,7
126
R30,2
42
S7,5
11,5
T38,1
53,5
Wø6
ø8
Q19,05
27
UR-NPSF 1/8”
R-NPSF 3/8”
VR-NPSF 1/8”
R-NPSF 3/8”
H53,9
79
B14,3
31,8
ModelDCC-220DCC-230DCC-240DCC-250
DL-03
Oil or grease up to NGLI 2 grade
Máx.: 250 bar - Mín.: 15 barMáx.: 80 ºC - Mín.: 0 ºCAdjustable (See model in the table below)
DCM series dualine valves are designed to simplify planning,installation,maintanance and toreduce inventory cost for user of lubrication system.This is achieved by using a modular typevalve section which is mounted on a machined base.Standard basis can hold from 1 to 4modular type valve sections.DCM series dualine valves operate in a hydraulic manner andcan be used with either oil or grease in dualine systems.Each modular type valve sectionlubricates two lubrication points.The DCM series dualine valves are available from 1 to 8 out-lets. Using the DCM series dualine valve ensures that each lubrication point received lubricantevery alternative cycle of the system operation.No no-return valves are used.Each modulartype valve section has two moving parts,a pilot piston which directs the flow of lubricantsand an adjustable discharge piston which discharges lubricant to the lubrication point.Eachvalve section normally has a packing gland assembly with viton seal in which an indicator pinmoves.By means of a cross porting facility in the base the two discharge lines from the mod-ular type valve section can be combined into one.The modular construction allows replace-ment of modular valve section without loosening the lubricant supply or delivery lines.
Lubricant
Work pressureTemperatureDischarge
MODEL (Double Outlet)DCM-220 DCM-230 DCM-250
0,09 0,20 0,600,60 1,20 5,00
Regulation
Regulation
MIN.MAX.
MODEL (Single Outlet)0,18 0,40 1,201,20 2,40 10,00
MIN.MAX.
Size203050
235
Two outletsFour outlets
Six outletsEight outlets
Nº outlet2468
Flow regulation per outlet (cm3)
Description
Requirement code - Distributor
Dualine ValvesDCM Series
Dualine
DCM 2
Size203050
Part Number for BaseModule DCM
DCM-254Example Order : Module DCM-20Example Order:
Specifications
C85117135
A13
18
D57
80
E18
23,5
J104
132
K78
100
F21
33
G18
21
L52
68
M26
34
N326
32
N452
64
O5
9
P10
13
Q25,4
40
R6,5
10
S25,4
31
V25,1
35
W25,4
31,5
Z36
48
AA22
28
AB13
18
AC26
32
XNPSF1/8”
NPSF1/4”
YNPSF1/8”
NPSF3/8”O’RING
2107
TO’RING2-011
UH8
11
B26
32
ModelDCM-20DCM-30DCM-50
A
X (OUT LET)
Y (INLET)
J(BASE F/4)
ØO
N4N3
L(BASE F/2)
K(BASE F/3)
M
QV
W
HG
C
D FE
BB B
ØP
T (ORIN'G)
R
Z(BASE F/1)
AAAB AC
DL-04
Description
Specifications
Dualine
These reversing valves can be activated by system pressure and adjustable-between 35 bar and 140 bar.The model VCI-R1000 reversing valve is used independent pumps in smalldual line systems.
Reversing ValveModel VCI-R1000
Oil or grease up to NGLI 2 gradeLubricantMín.: 35 bar - Máx.: 140 barWork oressureMín.: 0 ºC - Máx.: 80 ºCTemperatureBody and pistons : SteelSeal : Acrilo Nitrilo
Materials
Requirement code
VCI-R1000
LubricantGrease
OilAB
Manometerswith manometers
without manom1-
Adaptor andMicrointerruptor
with adap. & microint.without ad. & microint.
2-
VCIR-1000-B-1Reversing valve Mod. VCIR-1000 for oil withmanometers
Example Order:
DL-05
Description
Specifications
Requirement code
VCI-R40
Dualine Reversing ValveModel VCI-R40
These reversing valves are activated through system pressure. They controlnon-return and return systems.The VCI-R40 reversing valve is suitable forelectric motor driven,pneumatic or hydraulic operated pump units.This revers-ing valve is used on medium and large dualine systems.
LubricantGrease
OilAB
ManometersWith manometersWithout manom.
1-
Adaptor andMicrointerruptor
With adap. & micro. rightWith adaptor & micro. leftWithout adap. & microint.
24-
Assembly baseWith assembly base
Without assembly base3-
Oil or grease up to NLGI 2 gradeLubricantMín.: 35 bar - Máx.: 250 barWork pressureMín.: 0 ºC - Máx.: 80 ºCTemperatureBody and pistons : SteelSeal : Vitón
Materials
VCIR-40-A-1-4-3Reversing valve VCIR-40 to be used with grease availablewith manometers adaptor and microinterruptor andassembly base.
Order examples:
DL-06
DescriptionThe model VCI-R10 reversing valve operates in conjuction withpressure switches installed in the two lubricant supply lines.Thesereversing valves are used in end-of-line type dualine lubrication sys-tems. They can be used with electric motor driven,pneumatic orhydraulic operated pumps.
Specifications
Requirement code
DualineReversing Valve
Model VCI-R10
VCI-R10
LubricantGrease
OilAB
Frequency50 Hz60 Hz
56
Current110 V220 V380 V440 V
1234
37,5 L./min.
350 bar
Max. range of flow
Work pressure17,5 amp.Current of displacement1.65 amp.Current of retention
VCI-R10-2-5-AReversing valve, model VCI-R10 to beused with grease, feed with 220V currentand 50 Hz frequency.
Order examples:
DL-07
Description
Dualine Reversing ControlValve Mod.VCI-R20
The model VCI-R20 reversing valve directs the flow of lubricant alternately to the twogrease supply lines of a dualine lubrication system. After the pressure in the active sup-ply line has reached a value high enough to ensure the satisfatory operation of all thedualine valves in the system. The reversing valve operates to put this supply line in reliefto the reservoir and permits the other supply lines to receive lubricant delivery from thepump.The control of pressure is accomplished through the use of a spring , one end ofwhich is anchored to an adjustable screw and the other end to a fulcrum arm which isconnected to a gear segments. This gear segments in turn moves the control piston.Toincrease the operating pressure of system , the adjusting screw should be turned outand to lower the pressure turn it in. The adjusting screw bonnet serves not only to pre-vent leakage around the screw thread but also to lock the screw in place. The VCI-R20reversing valve can be used with electric motor driven , pneumatic or hydraulic operat-ed pumps.
Requirement code
VCI-R20
LubricantGrease
OilAB
VCI-R20-AReversing valve VCI-R20 to be used withgrease.
Order examples:
Specificacions
Oil or grease up to NGLI 2 grade
Mín.: 21 bar - Máx.: 49 bar
Lubricant
Work pressureMín.: 0 ºC - Máx.: 80 ºCTemperatureBody and pistons: steelSeals acrilo nitrilo. Optional: vitón
Materials
DL-08
OURLET
LINE 2
RETURN
LINE 2
RETURN
LINE 1
LINE 1LINE 2
LINE 2
RETURN
LINE 1
RETURN
LINE 1
SUPPLY
FRONTAL FACE BACK FACE
TOP FACE
12,7
28,5
12,7
23,8
22(m
ax)
57
139,
7
58,75
35 35
58,75
178
87,5
43,7
543
,75
58,75
35 35
58,75
NOTE:ALL THE CONNECTIONS ARE OF NPSF 1/4 "
OURLET
SUPPLY
DescriptionThe function of the VCAP-3 high pressure control valve , which is located directlyafter the VCI-R20 reversing valve is to augment the spring in the VCIR20 revers-ing valve thus permitting higher operating pressures in a loop type system. The util-isation of this principle in the VCAP-3 abviates the need for loop pipe to return tothe VCI-R20 and in this instance the loop will be short circuited.The system now becomes known as a short loop system. On the VCAP-3 highpressure control valve each of the supply lines are fitted with an adjustable springloaded piston type check valve. Lubricant discharged from the pump to each of thesupply lines in turn must pass through these check valves before returning to therespective return ports of the VCI-R20 reversing valve. Therefore the high pressurecontrol valve supplement resistance of the control spring in the reversing valve ,thus ensuring that an adjustable pressure in the range 35-210 bar can be devel-oped.
Specifications
Requirement code
VCAP-3
Dualine High Pressure ControlValve Model VCAP-3
With returnWithout return
12
VCAP-3-1Hight pressure control valve mod. VCAP-3 with return, without manometers.
Example Order:
Oil or greaseup to NLGI 2 gradeLubricantMín.: 21 bar - Máx.: 250 barAdjustment pressureMín.: 0 ºC - Máx.: 80 ºCTemperature
ManómetersWith manom.Without man.
3-
DL-09
165139
82
5432
TO REMOVE STOPPER TO FACILITATE THE REGULATION
6,35
114,
3
NPSF 3/8"GREASE INLET LINE
NPSF 3/8"GREASE OUTLET
2 x 8,5 mmMOUNTING HOLES
NPSF 3/8"RELIEF LINE
Description
Specifications
DualineRelief Valve/Strainer
Model VCA-F
The VCA-F relief valve/strainer combination can be used with large electricmotor driven, pneumatic or hydraulic operated grease pump stations. Therelief valve protects the lubrication system components from excess pressure.In the event of the system developing pressure in excess of the pressure set-tings on the relief valve , a pressure relief line opens and lubricant is allowedto flow back to the lubricant reservoir.
168-175 bar Range of relief valve
Oil or grease up to NLGI 2 gradeLubricant250 bar Max. pressure
Requirement code
VCA-F
VCA-FControl valve mod. VCAF; withoutmanometer.
Order examples:
Manometerwith man.
without man.1-
DL-10
e SEE
EE
SS
SS
DescriptionThe model VCC shut off valve is a piston type lubricant isolating valve. An airoperated cylinder is attached to the lubricant isolating piston. By applying airon the upper side of the air operated cylinder the lubricant isolating pistoncloses the lubricant port and air being applied on the lower side of the airoperated cylinder allows the lubricant isolating piston to open the lubricantport. The model VCC shut off valve is used to isolate lubricant supply linesthus allowing independent operation of certain zones in any lubrication sys-tem.The model VCC shut off valve is available in both a single line and adualine version.
Specifications
Requirement code
VCC
Shut Off ValveModel VCC
8 bar (pneumatic)
3 bar (pneumatic)ø1/4” NPTF
1/4” - 3/8” - 1/2” (NPSF)
Oil or grease up to NLGI 2 grade
Max. work pressure
Min. work pressureCompressed air thread
Conexion thread
Máx.: 250 bar (Hidraulic)Work pressure
Lubricant
ModelSingle path
Double path2122
øA1/4”3/8”1/2”
123
MODEL VCC-21SINGLE PATH
MODEL VCC-22DOUBLE PATH
Progressive Line
Dualine
DL-11
max
min
DescriptionThe model CU-693-2 flow switch is used as an alarm or trip signal if flow oflubricant in a line decreases. A typical example is the monitoring of oil flow inan oil circulating system. By connecting the flow switch contact to the controlcircuit of the machine being served by the oil circulating system , one caneither stop the machine or sound an alarm when the oil flowrate drops belowthe set point on the CU-693-2 flow switch.
Specifications
Requirement code
CU-693-2
Flow SwitchModel CU-693-2
70 bar
-6ºC a 93ºC0,3 bar in flow regulator1,13 a 53 litres./min.
Pressure range
Room temperatureMax. fall pressureRange work
DL-12
Control ValveFlow Regulator CU-986
3,8 L/min / 4 Rotation*3,8 L/min / 1 Rotation*
*Rotation regulation handle
Regulator
AB
Requirement code
CU-986
DescriptionThe model CU-986 flow rcontol valve are generally used to regulate the flow of lubri-cant in oil circulating systems. They can also be used to dump excess oil back totank.
Specifications
70 BAR
-6ºC a 93ºCCU-986-BCU-986-A
5,3 BAR a 15,2 Lts/min5,3 BAR a 3,8 Lts/min
Max. Work pressure
Room temperatureModel
Max. Flow pressure
3,8 L/min / 1 Rotation*3,8 L/min / 4 Rotation**Rotation regulation handle
Work range
Progressive Line
SLP-01
ValveMod. MJ
Mod.MJ-3MJ-4MJ-5MJ-6MJ-7MJ-8MJ-9
MJ-10
B62
77,593
108,5124
139,5155
170,5
A76
91,5107
122,5138
153,5169
184,5
Description
Specifications
MJ valves are designed for lubrication systems as fitted to machine tools and other similarequipment.A typical MJ valve consists of an inlet section, an end section and from 3 to 10 sections. A set ofvalves can feed up to a maximun of 20 lubrication points.Each sections of the valve can different discharge capacities.Each section marked with "T" has two discharge outlets, one for each side of the section.Each section marked with "S" has only one outlet, the other outlet is blocked thus doubling the dis-charge capacity to the open outlet.These valves could be fitted with accessories such as cycle indicators, blocked line indicators andpressure switches. These are used to monitor and control the operation of the valve.The close tolerance between the piston and the bore ensures an exact quantity of lubricant is dis-charged at high pressure.
Steel (zinc)
110 bar Oil or grease up to NLGI 2 grade
Materials
Max. pressureLubricant
80 ºC150 cycle/min.
Max. temp. operationMax. frequency
Size5
1015
Pulg3/cycle
0,0050,0100,015
cm3/cycle
0,0810,1630,245
Capacity descharge per module
Requirement code
* omit when not necessary
Cycles IndicatorWith Cycle Indicator
Without Cycle Indic.
MJ - - ( )
Top
10S
10T
15T
Base
Plug
Outlet0,030
0,015
0,010
0,015
Pulg3/cycle
CyclesIndicator
Plug
Outlet
Outlet Outlet
I-
CRCLCB
*Option Cross-PortingRight Cross Porting
Left Cross PortingBoth side Cross Porting
Mod
ule
Qua
ntity 3
45678
Mod
ule
Cap
acity 5
10
15
MJ3 - I - (10 SCR - 10 T - 15 T)Order examples:
Valve according to example
Type DischargeSingle Discharge
Double DischargeST
Composition per module
Progressive Line
The modules capacity 05, are not provided by indicator of cycles of functioning.Note :
The MR progressive single line valve are designed for lubrication system fitted to machine tools, machinery in iron andsteel manufacturing, hydraulic presses, rocker arm and other similar machines.In many assemblies these MR valves work as a primary valve for lubrication systems which contains MJ secondaryvalves.A typical MR valve consists of an inlet section, an end section and from 3 to 10 intermediate sections.A single valve can feed a maximun of 20 lubrication points.The valve sections could consists of different discharge capacities. Each section with "T" has two outlets, one of eachside of the section.Each section or module indicated with "S" has only one outlet, doubling the discharge capacity to the mentioned outlet.These valves can also be fitted with accessories such as cycle indicators, blocked line indicators and pressure switcheseused to monitor and control the functionofthe valve.The close tolerance between the pistonand the bore assures an exact quantity oflubricant is discharged even at high pres-sure.
SLP-02
Description
Specifications
Requirement code
ValveMod. MR
Size5
101520253035
Pulg3/cycle
0,0050,0100,0150,0200,0250,0300,035
cm3/cycle
0,0810,1630,2450,3270,4090,4910,573
Discharge Capacity per module
* omit when not necessary .
Steel (zinc)
180 barOil or grease up to NLGI 2 grade
Materials
Max. pressureLubricant
80 ºC150 cycles/min.
Max. operation temper.Max. frequency
Mod.MR-3MR-4MR-5MR-6MR-7MR-8MR-9
MR-10
A102
122,5143
163,5184
204,5225
245,5
B76
96,5117
137,5158
178,5199
219,5
Cycles IndicatorWith Cycle Indicator
Without Cycle Indic.
MR
Top
25 S
30 T
35 S
15 T
20 S
Base
Pluig
Outlet
Plug
Plug
Outlet
Outlet
Plug
Outlet
Outlet
I-
CRCLCB
*Option Cross-PortingRight Cross Porting
Left Cross PortingBoth side Cross Porting
Mod
ule
Qua
ntity 3
45678
Mod
ule
Cap
acity
5101520253035
MR 5 - I - (25 S CL - 30 T - 35 SCR - 15 T - 20 SCL)Example order:
- - ( ) CyclesIndicator
Plug
Valve according to example
Type DischargeSingle Discharge
Double Disch.ST
Composition per module
0,080
0,015
0,055
0,030
0,070
Pulg3/cycle
Progressive Line
The modules capacity 05 and 10, are not provided by indicator of cycles of functioning.Note :
The MX progressive single line valve, is operated by lubricant being delivered from a pumping unit. They delivereither grease or oil in exact measured quantities.Each segment of these valves can feed two points. A segment feeding two points is marked with a "T". By amethod called cross porting, a segment could be changed feed only one point to lubricate, therefore deliveringdouble the amount of the lubricant at this point. These segments are marked with a "S". Segments can be fittedwith different size pistons therefore allowing more or less lubricant to be delivered to cover the different require-mentof equipment to be lubricated.The valves are assembled with a minimun of 3 segments and a maximun of 10 segments. The quantity oflubricant being delivered depends on the diameter of the piston.
SLP-03
ValveMod. MX
Mod.MX-3MX-4MX-5MX-6MX-7MX-8MX-9
MX-10
A166,5200,2233,9267,6301,3335
368,7402,4
B138,1171,8205,5239,2272,9306,6340,3374
Description
Specifications
Steel (zinc)
250 barOil or grease up to NLGI 2 grade
Materials
Max. pressureLubricant
80 ºC150 cycle/min.
Max. operation temper.Max. frequency
Requirement code
* To omit when not necessary
Composition per module
Cycles IndicatorWith Cycle Indicator
Without Cycle Indic.
MX
Top
25 S
50 T
125 S
75 T
100 T
Base
Plug
Plug
Plug
Plug
Outlet
OutletOutlet
Outlet
Outlet
Outlet
I-
Type DeschargeSingle Discharge
Double Disch.ST
CRCLCB
*Option Cross-PortingRight Cross Porting
Left Cross PortingBoth side Cross Porting
Mod
ule
Qua
ntity
3456789
10
Mod
ule
Cap
acity
255075
100125150
MX - 5 - I - (25 SCL - 50 T - 125 SCR - 75 T - 100 T)
Size255075
100125150
Pulg3/cycle
0,0250,0500,0750,1000,1250,150
cm3/cycle
0,400,811,221,632,042,45
Capacity discharge per module
Example Order:
CyclesIndicator
Valve according to example- - ( )
0,100
0,075
0,325
0,100
0,050
0,100
Pulg3/cycle
Progressive Line
SLP-04
ValveMod. C-2000
C-2000-3C-2000-4C-2000-5C-2000-6C-2000-7C-2000-8C-2000-9
C-2000-10
A100,2120,5140,8161,1181,4201,7222
242,3
B86,1
106,4126,7147
167,3187,6207,9228,2
Model
Description
Specifications
C-2000 valves are the main components of a progressive single line system. The assembled valves with 3 to 10 meter-ing sections, distribute and provide grease or oil from the pump to the different lubrication points .The lubricant discharge capacity of each section is determined by the size of the piston.Each section can feed two different points or by means of a simple modification on top of eachsection changing a smallconical plug for a flat one, the two outlets are combined doubling the lubricant to one of the outlets.The second outlet can now be plugged.These valves can be fitted with accessories such as a cycle indicator, blocked line indicators and pressure switcheswhich ca be used to monitor and control function of the valve.The close tolerance betwen the piston and the bore ensures an exact quantity of lubricant is discharged at high pres-sure.
Steel (zinc)
250 barOil or grease up to NLGI 2 grade
Materials
Max. pressureLubricant
80ºC150 cycle/min.
Max. operation temper.Max. frequency
Size5
101520253035
Pulg3/cycle
0,0050,0100,0150,0200,0250,0300,035
cm3/cycle
0,0810,1630,2450,3270,4090,4910,573
Capacity discharge per module
Requirement code
Cycles IndicatorWith Cycle Indicator
Without Cycle Indic.
C-2000
Top
20 T
35 T
30 T
20 T
Base
Outlet Outlet
Plug
Plug
Outlet
Plug
Outlet
I-
CRCLCB
*Option Cross-PortingRight Cross Porting
Left Cross PortingBoth side Cross Porting
Mod
ule
Qua
ntity 3
456789
10
Mod
ule
Cap
acity
5101520253035
C2000 - I - (20T - 35 TCR - 30TCB - 20T)
Outlet
Example Order:
CyclesIndicator
Valve according to example
- - ( )
* Omit when not necessary
Type DischargeSingle Discharge
Double Disch.ST
Composition per module
0,010
0,085
0,010
0,050
0,035
Pulg3/cycle
Progressive Line
The modules capacity 05 and 10, are not provided by indicator of cycles of functioning.Note :
SLP-05
Progressive DividerValve Mod. MU
MU-3MU-4MU-5MU-6MU-7MU-8MU-9MU10
“L”115.4138.9162.3185.7209.1232.6256.1279.6
“M”90.9114.3137.7161.1184.5207.1230.6254.1
Model
Description
Specifications
MU valves are the main components of Cirval progressive single line system. Its modular design makes the system easy to assembly, easyto modify and maintain without the need of removing the feeding line to the valve set and the points being lubricated.These valve consist of 3 or more valve modules assembled on a segmented base. The valve modules can have 1 or 2 outlets doubling thelubricant discharge when the outlets are combinedThe close tolerance between piston and bore allow the modules to deliver an exact quantity of lubricant at high pressure.
These modular valves are designed to operate with either grease or oil in manual systems or automaticsystems and are used on all kinds of industrial machinery.These valves can also be fitted with accessories such as cycle indicators, blocked line indicators andpressure switches. These accessories are used to monitor and control the operation of the valves.
Steel (zinc) - (nickel quimic or stainless for special order).Seal: Acrilo nitrilo - Option: vitón.
250 barOil or grease to NLGI 2 grade
Materials
Max. pressureLubricant
80ºC150 cycle/min.
Max. operating temper.Max. frequency
Size5
10152025303540
Pulg3/cycle
0,0050,0100,0150,0200,0250,0300,0350,040
cm3/cycle
0,0810,1630,2450,3270,4090,4910,5730,655
Discharge capacity per outlet
Part Numbers
Cycles IndicatorWith Cycle Indicator
Without Cycle Indic.
MU
Top
15 T
10 S
15 T
20 S
35 T
Base
Outlet
Outlet
Outlet
Outlet
Plug
Plug
Outlet
Outlet
Plug
I-
CRCLCB
*Option Cross-PortingRight Cross Porting
Left Cross PortingBoth side Cross Porting
Mod
ule
Qua
ntity
3456789
10
Mod
ule
Cap
acity
510152025303540
MU - 5 - I ( 15T -10 SCR - 15 T - 20SCL - 35 T)Example :
- - ( )CycleIndicator
Plug
Valve according to example
* Omit when not necessary
Composition per module
Type DischargeSingle Discharge
Double DischargeST
0,005
0,075
0,035
0,005
0,035
0,015
Pulg3/cycle
Progressive Line
The modules capacity 05 and 10, are not provided by indicator of cycles of functioning.Note :
MD-2
INLE
TIN
LET
MD-3
1/2 1/2
INLE
T
MD-4
1/4 1/2
1/4
1/4 1/4
INLE
T
1/6
MD-6
1/4 1/4
1/6
1/6
1/6
1/6
1/6
37
INLET NPSF 1/8''
7,1
2230
54.29.8
44.4
5
32.0
5
81.873.8
30 21.9
28.27.
05
OUTLETNPSF 1/8''
OUTLET NPSF 1/8( MD-6)
SLP-06
DescriptionMD valves are designed to be used in progressive single line centralized lubrication systems witheither grease or oil. These valves consist of 2 steel pieces with ‘o’ rings. They can feed 2,3 4 or6 lubricant points. Valves with 2,3 and 4 points require 1.31 cm3 of lubricant to complete an entirecycle. An MD-2 valve will divide this volume in 2 outlets of 0.655 cm3. An MD-4 will divide thevolume in 4 outlets of 0.327 cm3. An MD-6 requieres 0.983 cm3 of lubricant to complete an entirecycle, and will divide this volume in 6 equal outlets of 0.16 cm3.Features: Delivery of meassured quantities of lubricant. Economic and compact design. Easy toassembly on new or old machines.
Especificaciones
Requirement code
ValveMod. MD
Steel (zinc)
250 barOil or grease up to NLGI 2 grade
Materials
Max. work pressureLubricantAvailable with Cycle Indicator
2 OUTLETS3 OUTLETS4 OUTLETS6 OUTLETS
MD
2346
MD-2, MD-3 y MD-4MD-6
1,31 cm3
0,98 cm3
Discharge Volume *
*Lubricant needed to make a completecycle of the dividing valve.
MD-2MD-3 MD-4MD-6
2-0,655 cm3
2-0,655 cm3 + 1-0,655 cm3
4-0,327 cm3
6-0,160 cm3
Discharge Volume
MD-3Valve mod. MD with 3 outlet.
Order examples:
Progressive Line
The MG progressive grease valve operates hydraulically and can deliver grease or oil in exact measured quanti-ties.The section of these valves can feed two points. Sections indicated with "T" has two outlets, or through a methodcalled cross porting, a section would be able to feed one lubrication point, doubling the quantity of lubricant beingdischarged.These modules are indicated with "S".Different size sections allows different quantities to be discharged.The valves are assemblied with a minimun of 3 sections and a maximun of 10 sections.The delivery volume of a section depends on the diametre of the piston.Accessories such as cycle indicators, blocked line indicators and pressure switches can be fitted.These are used to monitor and controlthe operation of the valve.
SLP-07
ValveMod. MG
Mod.MG-3MG-4MG-5MG-6MG-7MG-8MG-9
MG-10
A220260300340380420460500
B195235275315355395435475
Description
Specifications
Steel (zinc)
250 bar Oil or grease up to NLGI 2 grade
Materials
Max. pressureLubricant
80 ºC150 cycle/min.
Max. operation temper.Max. frequency
Requirement code
* omit when not necessary
Composition per module
Cycles IndicatorWith Cycle Indicator
Without Cycle Indic.
MG
Top
360 S
150 T
150 S
360 T
360 T
Base
Plug
Plug
Plug
Plug
Outlet
OutletOutlet
Outlet
Outlet
Outlet
I-
Type DischargeSingle Discharge
Double Disch.ST
CRCLCB
*Option Cross-PortingRight Cross Porting
Left Cross PortingBoth side Cross Porting
Mod
ule
Qua
ntity
3456789
10
Mod
ule
Cap
acity 150
360
MG - 5 - I - (360 SCL - 150 T - 150 SCR - 360 T - 360 T)
Size150360
Pulg3/cycle
0,1500,360
cm3/cycle
2,456,00
Discharge capacity per module
Order examples:
CyclesIndicator
Valve according to example- - ( )
0,870
0,360
0,660
0,360
0,150
0,360
Pulg3/cycle
Progresive Line
Unique Line
UL-01
Oils
4 bar (Máx.= 10 bar)Máx.: 80 ºC - Mín.: 0 ºC2 Drops / min.4 Drops / min.16 Drops / min.
DescriptionCFT restrictors are lubricant flow units in a centralized oil lubrication systems.These are 3 different size of units allowing for the different lubrication require-mentson a machine.
The units can be assembled by screwing them directly into the lubricationpoint or by assembling them onto manifolds that holds from 1 to 6 restrictors.
Functioning: The restrictors consist of a cylindrical chamber with an extreme-ly precise diameter hole, where a needle keeps an exact oriface when assem-bled.
The differences in the surfaces in these oriface determines the oil flow. A fil-ter and an internal non return valve completes the restrictor unit.
NOTE:As the restrictor body has the same thread on both sides, anyof the connectors in the table below can be used on any side.
CONNECTION BLOCK
Specifications
Lubricant
Work pressureTemperature
Discharge formodel
FT-0FT-1FT-3
Requirement code
Flow2 drop/min.4 drop/min.
16 drop/min.
CFT BCUL
Dosimeter Conexion Block
013
A
B
== NPTF 1/8''
21NPTF 1/8''
Exag. E/C. 10
7
7
17,5
Prof. = 17,5
INLETNPSF 1/8''
2 x 4,25MOUNTING HOLES
10
3,5
C
Block of 2 outlest Mod. BCUL-02Block of 3 outlets Mod. BCUL-03Block of 4 outlets Mod. BCUL-04Block of 5 outlets Mod. BCUL-05Block of 6 outlets Mod. BCUL-06
23456
Unique LineResistence Dosage
(Restrictor) Serie CFT
BCUL-02BCUL-03BCUL-04BCUL-05BCUL-06
A3618365472
Nº Outlet23345
B577492110128
C3434343434
Model
Diam. 3/16” (4,76 mm.)
Diam. 1/4” (6,35 mm.)
CU-84-A + CU-81-AA1
CU-84-B + CU-81-B1
Diameter Pipe Connector
Order examples:
Dosimeter CFT-1Connection Block BCUL-2
CFT-1-2
UL-02
Unique lineDIRECT ANSWER DOSAGE
CSKN Model
Mineral Oil ISO 320 / 40º C
22 - 28 bar50 bar
Description
The injector type metering unit is supplied with oil from the pump and chargedwith a measured quantity of lubricant.The injector type metering unit is a one shot metering unit with a fixed deliv-ery ate.These injector type metering units are available in three different sizes.The range is from 0.05 to 0.30 cm3.They can be screwed directly into the lubrication point or they ca be assem-bled on to manifolds.
Note: As the body has the same thread in both sides they can befitted with the above connectors on both sides.
Manifold
Specifications
Lubricant
Pressure under workMáx. Operation Pressure
Requirement Code
Flow0,05 cm3
0,10 cm3
0,30 cm3
CSKN BCUL
51030
10
10
INLETNPSF 1/8''
Prof. = 17,52 x Ø4,25
MOUNTING HOLES
17,510
C
3,5
BA= =
NPTF 1/8''
H
NPTF 1/8"
6,5
10
2 outlets block Mod. BCUL-023 outlets block Mod. BCUL-034 outlets block Mod. BCUL-045 outlets blcok Mod. BCUL-056 outlets block Mod. BCUL-06
23456
BCUL-02BCUL-03BCUL-04BCUL-05BCUL-06
A3618365472
Nº outlets23456
B577492110128
ModelInjector type metering unit
CSKN 05CSKN 10CSKN 30
C434352
Discharge0,05 cm3
0,10 cm3
0,30 cm3
H30,530,539,5
Modelo
Diám. 3/16” (4,76 mm.)
Diám. 1/4” (6,35 mm.)
CU-84-A + CU-81-AA1
CU-84-B + CU-81-B1
Line Diameter Connectors
Example Order : CSKN-5-4
Dosimeter CSKN-5Block conexión BCUL-4
Dosimeter Block de conexión
UL-03
Oil or fluid greaseup to NLGI 1 grade
Oil Grease0,014 a 0,044 grs.
80 bar
240 bar
100 bar
15 bar
DescriptionCUL injectors are part of centralized lubrication systems used to deliverexact quantities of grease or oil to diffent points in a machine.They can be made up as individual units or assembled on manifolds hold-ing up to 6 units.The easy quantity adjustment and external indication allows for fast and effi-cient control of the lubricant quantity independently from every injector..
Specifications
LubricantCUL - 10
Min. PressureMax. PressureRecomm. pressureRelief Pressure
Regulable discharge
Requirement Code
GreaseOil
CUL -10
AB
CUL-10CUL-20
1020
Block for 1 Inyector Block for 2 InyectorsBlock for 3 InyectorsBlock for 4 InyectorsBlock for 5 InyectorsBlock for 6 Inyectors
Dos
imet
erQ
uant
ity
123456
Unique Line CULINJECTOR
A37557594113132
Cant.123456
B486786
105124143
Oil or fluid greaseup to NLGI 1 grade
Oil Grease0,014 a 0,114 grs.
80 bar
240 bar
100 bar
15 bar
Specifications
LubricantCUL - 20
Min. pressureMax. pressureRecomm. pressureRelief Pressure
Regulable Discharge
Order example: CUL-10-A-2Two CUL 10 injectors, for grease with itscorresponding block.
CUL-10
A396183
105127149
Cant.123456
B507294116138160
CUL-20
433573
CDE
525190
Mod. CUL-10 CUL-20
0,014 a 0,044 grs.
80 bar
240 bar
100 bar
15 bar
0,014 a 0,114 grs.
80 bar
240 bar
100 bar
15 bar
UL-04
Unique Line CVCRINJECTOR
Oil
0,025 a 0,400 cm3
20 bar
DescripciónCVCR injectors are part of a centralized lubricant system. They are usedto deliver measured quantities of oil to different points of lubrication of amachine.The units are assembled on manufolds.The flow can be adjusted allowing a fast and efficient control of the lubri-cation in an independent way to every lubrication point.Replacement: The injectors can be assembled on manifolds and areeasily replaced without removing connections or lines.
Regulation: Turning the adjusting screw (clockwise) would decrease the inletquantity of lubricant. Each turn is equal to 0.025 cm3.
Specifications
Lubricant
Regulable DischargeMin. Pressure
60 barMax. Pressure
Requirement Code
CVCR
Dosage QuantityBlock for 1 Injector
Block for 2 InjectorsBlock for 3 InjectorsBlock for 4 InjectorsBlock for 5 InjectorsBlock for 6 Injectors
123456
CVCR-1CVCR-2CVCR-3CVCR-4CVCR-5CVCR-6
A426792117142167
B-
255075
100125
Modelo
Mín.Máx.
Flow0,025cm3
0,400 cm3
Regul.
UL-05
Unique LineCSL 1 GREASE
INJECTORS
DescriptionCSL 1 injectors are designed to operate in a parallel single line centralized lubricant system.These units operate in systems with pressures up to 240 Bar.They are suitable for oil or grease up to NLGI 2.The lubricant discharge capacity is adjustable through an external adjusting screw.Each unit is also fitted with an indicator stem which confirms the operation of the injector.CSL 1 injectors are fitted with a grease nipple and cap which can be used for manual lubrication.The injectors are normally manifold mounted.
Specifications
Requirement Code
CSL 1
Descharge Operation Pressure ConexionsMin.
0.131 cm3
Máx.
1.31 cm3
Min.
127 bar
Máx.
241 bar
Typical
172 bar
Relief
41 bar
Inlet Blockcon.
3/8 NPSF
Injectoroutlet
1/8 NPSF
1 Injector2 Injectors3 Injectors4 Injectors5 Injectors6 Injectors7 Injectors
Injector Quantity1234567
LubricantGrease A
Example order CSL1-A-2Two injectos CSL1 for grease with the corresponding block
“A”**
326395
127191
ModelCSL1-1CSL1-2CSL1-3CSL1-4CSL1-5CSL1-6CSL1-7
“B”6376
108140171203267
*IT HAS AN ALONE HOLE OF ASSEMBLY
UL-06
Unique Line CSL 11 GREASEINJECTORS
Requirement Code
CSL 11
DescriptionCSL 11 injectors are designed to operate in a parallel single line centralized lubricant system.These units operate in systems with pressures up to 240 Bar.They are suitable for oil or grease up to NLGI 2.The lubricant discharge capacity is adjustable through an external adjusting screw.Each unit is also fitted with an indicator stem which confirms the operation of the injector.CSL 11 injectors are fitted with a grease nipple and cap which can be used for manual lubrication.Units have a 1/2” NPT female inlet connection.
Mod. CSL-11Specifications
Discharge Operation PressureMin.
0.82 cm3
Máx.
8.2cm3
Min.
69 bar
Máx.
241 bar
Típical
172 bar
Relief
55 bar
UL-07
Unique Line CONTROL VALVEMod. CVA 850
108
NPSF 1/4"AIR SUPPLY
NPSF 1/4"RESERVOIR RETURN
NPSF 3/4"LUBRICANT INLET
DescriptionThe model CVA 850 vent valve is used with CSL injectors.They allow the pressure of the system to vent back to the reservoir once the system hasoperated.During the system operation, air is applied to the vent valve closing the vent port andallowing the pump to develop the required system operating pressure.Once the pressure has been reached, the pump stops, the air pressure is removed fromthe vent valve and the vent port opens.
Specification
Code Requirement
CVA-850
8 bar (pneumatic)
3 bar (pneumatic)262 bar (Hydráulic)Any positionOil or grease up to NLGI 2 grade
Zinc Steel body / Aluminium Cover
Max. air pressure
Min. air pressureMax. lub. pressureAssembly
LubricantSup. treatment
Pumps and Centrals
BC-01
Dualine
Requirement Code
Example Order:
These sub-assemblies utilises a double piston and cylinder set.They are suitable for all kinds of systems using grease or oil.The casings are made of cast iron. The drive shaft rotates in twoangular contact bearings. Two eccentrics are fitted to the driveshaft. These operate the pistons via two connecting rods and twoneedle bearings. The double pistons and cylinder set allows oper-ation without check valves.
DJ5DJ4
Double piston pump BCE-DJ-4
Requirement Code for shirt and piston set
Requirement Code reparation STD kit
BCE-DJ-4 - CDJ-4505BCE-DJ-5 - CDJ-5505
BCE-DJ-4 - CDJ-4506BCE-DJ-5 - CDJ-5506
Pump Sub-AssemblyBCE-DJ4 and BCE-DJ5
Lubricant: Oil or grease up to NLGI 2 grade
45
BCE-DJ
Flow462/563 cm3/min.
828/1010 cm3/min.
Specificaciones
Description
MODELS BCE-J4 BCE-J5462 cm3/min. 828 cm3/min.563 cm3/min. 1010 cm3/min.
210 bar 210 bar250 bar 250 bar
Flow (Motor 50Hz)
Flow (Motor 60Hz)Operation PressureMax. pressure
øA168342
ModelBCE-DJ-4BCE-DJ-5
B181
295,5
C282,5440
D190,5387
E127280
F102203
G107203
H101,5165
J92,25157
K38,7582,5
øL25,4
31,75
øM149298
Conexión NNPSF1/4”x18f/p.NPSF1/2”x14f/p.
BC-02
The central pumping station model ECB-AD 42 has been designed to satisfy f the heavy industry. Thesecan provide either oil or grease in almost any lubrication system application.These stations include the BCE-DJ4 pump sub-assembly driven by a geared motor unit.Assembled on sturdy base plate they are completed by a reversing valve and a relief valve if used as adualine unit.The robust base plate as well as the pump casing design allows the use of large reservoirs for bothgrease and oil. The large reservoirs allows for extended refill intervals.Reservoirs can also include low and hi level indicationwith an automatic refilling option.
Pump462/563 cm3
LubricantGrease
Oil AB
DepositDGL 40
DAL 11540115
4
Description
Code Requirement
Central Pumping StationModel ECB-DC-42
ECB-DC 42
Dualine
Oil or grease up to NLGI 2 grade
Máx.: 250 barAdjustable (max: 210 bar)FLOW 462 cm3/min.MOTOR 1 HP - 220/380 V. - 50 Hz. - 1420 rpmFLOW 563 cm3/min.MOTOR 1 HP - 440 V. - 60 Hz. - 1730 rpm
Lubricant
Work pressureRelief pressure
Motor 50 HzPumpBCE-J4 Motor 60 Hz
Specifications
ECB-DC42-4-40-A4Order example:
S. LíneVCIR-40
Revers. Valve04
A720
ModeloDC-42-4
B670
C685
D635
BC-03
Description
Dualine
Specificaciones
Double piston pumpMod. BCE-DJ25
106 cm3/min. 341 cm3/min.87 cm3/min. 280 cm3/min.
1 2
Máx.: 250 barAdjustable (Máx. 210 bar)
These sub-assemblies utilises a double piston and cylinder set. They are suit-able for all kinds of systems using grease or oil.The casings are made of cast iron. The drive shaft is fitted with a worm drive.The secodary shaft is fitted with a drive wheel andis located by two angularcontact bearings. Two eccentrics are fitted to the secondary shaft. These oper-ate the pistons via two connecting rods and two needle bearings. The doublepistons and cylinder set allows operation without check valves.
Pump Model BCE-DJ25Type: Dual piston ans cylinder set with internal reduction.
Flow (Motor 50 Hz)Flow (Motor 60 Hz)Work PressureRelief Pressure
Oils or grease up to NLGI 2 gradeLubricant
12
Requirement CodeExample :
BCE-DJ25 -
Flow87/106 cm3/min.
280/341 cm3/min.
Cirval Pump BCE-DJ25-1
BCE-DJ25-1 - CB-9133BCE-DJ25-2 - CB-9233
BCE-DJ25-1 - CB-9134BCE-DJ25-2 - CB-9234
Requirement code shirt and piston set
Requirement code Reparation STD set
12012006
BC-04
The central pumping station model ECB-AD 25 has been designed to satisfy f the heavy industry. Thesecan provide either oil or grease in almost any lubrication system application.These stations include the BCE-DJ25 pump sub-assembly driven by an electric motor.Assembled on sturdy base plate they are completed by a reversing valve and a relief valve if used as adualine unit.The robust base plate as well as the pump casing design allows the use of large reservoirs for bothgrease and oil. The large reservoirs allows for extended refill intervals.Reservoirs can also include low and hi level indication with an automatic refilling option.
S. LíneVCIR-40
Rev. Valve04
Flow87/106 cm3
280/341 cm3
12
LubricantGrasaAceite
AB
ReservoirDGL 40DAL 30
DAL 115
4030115
Description
Requirement Code
PUMPING CENTRAL STATIONMODEL ECB-DC25
ECB-DC25
Specifications
ECB-DC25-2-40-A-4Example :
Dualine
Prog. Line
Oil or grease up to NLGI 2 grade
Máx.: 250 barAdjustable (max: 210 bar)FLOW 87 cm3/min.MOTOR 1 HP - 220/380 V. - 50 Hz. - 1420 rpmFLOW 106 cm3/min.MOTOR 1 HP - 440 V. - 60 Hz. - 1730 rpm
Mod. DAL-30: 30 Lts. - Mod. DAL-115: 115 Lts. (Oil)Mod. DGL-40: 40 Kg. (Grease)
Lubricant
Work pressureRelief pressure
Reservoir Capacity
Motor 50 Hz
Motor 60 Hz
PumpBCE-J25 (1)
FLOW 280 cm3/min.MOTOR 1 HP - 220/380 V. - 50 Hz. - 1420 rpmFLOW 341 cm3/min.MOTOR 1 HP - 440 V. - 60 Hz. - 1730 rpm
Motor 50 Hz
Motor 60 Hz
PumpBCE-J25 (2)
12012006
- - - -
BC-05
Description
Dualine
Specifications
123
Requirement CodeExample Order>
BCE-DJ10
Flow87/106 cm3/min.
45/55 cm3/min.22/28 cm3/min.
106 cm3/min. 55 cm3/min. 28 cm3/min.87 cm3/min. 45 cm3/min. 22 cm3/min.
Máx.> 250 barAdjustable (Máx. 210 bar)
These sub-assemblies utilises a double piston and cylinder set. They are suit-able for all kinds of systems using grease or oil.The casings are made of cast iron. The drive shaft is fitted with a worm drive.The secodary shaft is fitted with a drive wheel and is located by two angularcontact bearings. Two eccentrics are fitted to the secondary shaft. These oper-ate the pistons via two connecting rods and two needle bearings. The doublepistons and cylinder set allows operation without check valves.
1 2 3
Pump Model BCE-DJ10Type: Piston and cylinder.
Flow (Motor 60 Hz)
Flowl (Motor 50 Hz)
Work PressureRelief Pressure
Oil or grease up to NLGI 2 gradeLubricant
Pump Cirval BCE-DJ-10-1
Double Piston PumpModel BCE-DJ10
BCE-DJ-10-1 - CB-9133BCE-DJ-10-2 - CR-9233BCE-DJ-10-3 - CR-9333
BCE-DJ-10-K
Requirement Code for shirt and piston set
Requirement Code STD Reparation
BC-06
Pump87/106 cm3
45/55 cm3
22/28 cm3
123
LubricantGrasaAceite
AB
DepositDGL-10DAL-30
1030
Description
Requirement Code
Central Station PumpModelo ECB-DC-10
ECB-DC 10
Oil or grease up to NLGI 2 gradeMáx: 250 barAdjustable (máx: 210 bar)
LubricantWork PressureRelief Pressure
Mod. DAL-30 (steel) : 30 Lts. (oil)Mod. DGL-10 (steel) : 10 Kgs (grease)
Deposit Capacity
Specifications
ECB-DC10-2-10-A-4
The central pumping station model ECB-DC 10 has been designed to satisfy the industry. These can provide either oil orgrease in almost any lubrication system application.These stations include the BCE-DJ10 pump sub-assembly driven by an electric motor.Assembled on sturdy base plate they are completed by a reversing valve and a relief valve if used as a dualine unit.The robust base plate as well as the pump casing design allows the use of large reservoirs for both grease and oil. Thelarge reservoirs allows for extended refill intervals.Reservoirs can also include low and hi level indication with an automatic refilling option.
Order example:
S. LíneaVCIR-40
Rev. Valve04
Dualine
FLOW 87 cm3/min.MOTOR 0,5 HP - 220/380 V. - 50 Hz. - 1405 rpmFLOW 106 cm3/min.MOTOR 0,5 HP - 440 V. - 60 Hz. - 1710 rpm
Motor 50 Hz
Motor 60 Hz
Motor 50 Hz
Motor 60 Hz
Motor 50 Hz
Motor 60 Hz
PumpBCE-J10(1)
FLOW 45 cm3/min.MOTOR 0,5 HP - 220/380 V. - 50 Hz. - 1405 rpmFLOW 55 cm3/min.MOTOR 0,5 HP - 440 V. - 60 Hz. - 1710 rpm
PumpBCE-J10(2)
FLOW 22 cm3/min.MOTOR 0,5 HP - 220/380 V. - 50 Hz. - 1405 rpmFLOW 28 cm3/min.MOTOR 0,5 HP - 440 V. - 60 Hz. - 1710 rpm
PumpBCE-J10(3)
Prog. Linea
BC-07
Oil or grease up to NLGI 2 grade5 cm3 x piston displacement
Model Grease (Kg)-A Oil (cm3)-B4 A 1 2,7 30005 A 1 4,2 45006 A 1 6,4 7000
These robust manual pumps are designed for heavy duty applications. Theycan supply lubricant in a reliable way at high pressure to distributors in singleand dualine systems.Ideal for those systems that requires manual centralized lubrication.They operate with oil or grease. Reservoir are fitted with floats or followerplates and three different sizes are available. A visual level indicator is fitted.
Lubricant
350 barMax. work pressure
Discharge
Reservoir Capacity
4 5 6
Grease2,7 Kg4,2 Kg6,4 Kg
ReservoirOil
3000 cm3
4500 cm3
7000 cm3
SystemD. LíneS.Líne
DLSL
LubricantGrease
OilAB
Description
Specifications
Requirement Code
Manual Pump Mod.BCM-A1-A/B
BCM A1Manual pump double line to grease and reservoir of 4,2 Kg.BCM-DL-5A1-AExample :
Dualine
CDA-4046-1
CDA-4045-1
Prog. Line
Requirement Code for body and piston kit
Requirement Code for STD reparation kit STD
12012006
- - -
BC-08
Manual PumpBCMSL
394
9033
467
146.50
571
105.00
121.00
DescriptionA manually operated pump with an incorporated single line progressive valve. Theycan feed from 1 to 16 lubrication points on a machine. Correctly measured quantitiesof lubricant is delivered to each point.A practical and economical system that can be applied to machines suitable for man-ual lubrication systems.This system also helps to prevent over lubrication.System kits are available for machines in the agricultural industry.Once installed the operator can lubricate the machine even when it is operating.
Module QuantityUp to 6 points Up to 8 points
Up to 10 pointsUp to 12 points
Up to 14 pointsUp to 16 points
345678
LubricantGrease
OilAB
Requirement Code
BCMSL-1A1 - MJ -
BCMSL-1A1-A-MJ-5Manual operated pump with 500 gram greasereservoir and distributor model MJ-5 serving up to10 lubrication points.
Order example:
STANDARD MJ-10 0,16 cm3/Cycle
ORDER MJ-5 0,08 cm3/Cycle
MJ-15 0,25 cm3/Cycle
Dosage per lubrication point
CDA-1046-1
CDA-1045-1
Prog. Line
Requirement Code for body and piston kit
Requirement Code for reparation STD kit
BC-09
Dimensiones GeneralesGeneral Dimensions- Pneumática PumpSimple Line Bomb BCN-AC-1/2
Pneumática Pump
Hydraulic Pump
Simple Line Pump BCH-TP
Pneumatic/HydraulicOperated Lubrication Pump
BCN/BCH
Requirement Code
Flow 0,70-3,20Flow 0,45-2,20Flow 0,13-0,70
BCN-AC
012
ReturnSpring
Pneumátic12
Mod.BCN
0,70 3,20
0,45 2,20
0,13 0,70
AC-01AC-02AC-11AC-12AC-21AC-22
2 10
2 10
2 10Pneu
mát
icHi
dráu
lica
SpringPneumátic
SpringPneumátic
SpringPneumátic
22:1
35:1
100:1
AC-0-1030-2
AC-1-1030-2
AC-2-1030-2
Force permotivation
Return Line PressureRelationship
Reparationkit
DischargeHub (cm3)
min. máx. min. máx.
MotivationPressure BAR
General Dimensions - Hydraulic pump
Requirement Code
BCH-CT
ReturnSpring
Hydraulic12
Flow0,29 - 1,050,57 - 2,78
12
Mod.BCH
CT1-1CT1-2CT2-1CT2-2
0,29 1,050,29 1,050,57 2,780,57 2,78
17,5 1407 14021 14014 140
springhidráulicspring
hidráulic
6:1
2:1
CT-1-1030-2
CT-2-1030-2
Force permotivation
ReturnAction
PressureRelationship
ReparationKit
Discharge perhub (cm3)
min. máx. min. máx.
Motivation pressure(Kg./cm2)
Pneumatic and hydraulic operated pumps usedin various applications, They can be adapted todifferent models of grease or oil reservoirs. Usedmainly in single line progressive systems. Thesepumps are very robust. They have an adjustabledischarge capacity. The positive displacementpiston and cylinder set guarantees a measuredquantity of lubricant even at very high operatingpressures.
BCN-AC-1-2Pneumatic Pump BCN, with flow 0,45 a 2,2 cm3 with pneumatic return.
Example Order:
Progressive Line
BC-10
Dimensiones GeneralesGeneral Dimensions - Pumping Stations for grease
Dimensiones GeneralesGeneral Dimensions - Pumping Stations for oil
Central Station PumpECB-AC/CT-TP
AIR
SU
PPLY
- N
PSF
1/4"
(C) (D
)
(E)
(H)(G
)
(F)
(A x B)
NPSF 1/4" X 18 f/p.
(J)(I)
(K)
LUBRICANT OUTLET
Mod.ECB-X-TP-28-AECB-X-TP-30-AECB-X-TP-32-AECB-X-TP-34-A
(D)
598
598
(C)500
(E)
778
(F)
562
(G)
382
382
(H)283
(I)190
190
240
240
(J)165
165
210
210
(K)102
102
152
152
(AxB) (Ancho x Prof.)
250,5 x 160250,5 x 160
250,5 x 213,5250,5 x 213,5
(J)(I)
LUBRICANT OUTLET
(C)
NPSF 1/4" x 18 f/p.
(G)
(H)
(F)
(K)
(A x B)
AIR
SU
PPLY
NPS
F 1/
4"
(D)
(E)
Mod.ECB-X-TP-28-BECB-X-TP-30-BECB-X-TP-32-BECB-X-TP-34-B
(D)
540
540
(C)442
(E)
720
(F)
562
(G)
382
382
(H)283
(I)190
190
240
240
(J)165
165
210
210
(K)102
102
152
152
(AxB) (Ancho x Prof.)
250,5 x 160250,5 x 160
250,5 x 213,5250,5 x 213,5
These central pumping stations can consist of severalcombinations of reservoirs and pumps. On the tablesbelow the various combination can be seen.These units can feed large machines with varied quantityof lubrication points.They can be operated either by the machine cycle,a sys-tem controller or a PLC.Operating methods should however guarantee the appro-priate lubrication of the equipment.
GreaseOil
LubricantDeposit CapacityGrease
1,300 Kg.1,800 Kg.4,00 Kg.6,500 Kg.
Oil1,700 cm3
2,500 cm3
5,800 cm3
8,300 cm3
28303234
AB
Requirement Code
ECB TP
ECB-2-TP-34-ACentral Pumping Station, consisting of BCN-AC-2 pump and an acrylic grease reser-voir of 6,5 Kgs. capacity.
Example Order:
PumpBCN-AC-01BCN-AC-02BCN-AC-11BCN-AC-12BCN-AC-21BCN-AC-22BCH-CT-11BCH-CT-12BCH-CT-21BCH-CT-22
12345611122122
Progressive Line
BC-11
Central pumping StationECB AC/CT-P/N
Dimensiones GeneralesGeneral dimensions of Pumping Central with policarbonate deposit
General dimension of Pumping Central with metallic deposit
Central Pumping Stations with different types ofoil reservoirs.Example Order: ECB-1-P-1Central Pumping Statons model ECB-1-M-1consistin of one pneumatic operated pumpmodelBCN-AC-01 fitted to a 3 liter polycarbon reser-voir.
1 pump2 pump
Pump Quantity
12
DepositPolicarbonate 3 Lts.
Metallic 15 Lts.PM
Requirement Code
ECB
ECB-1-M-1Central Pumping Stationl Model ECB-1-M-1 consist-ing of one pneumatic operated pump model BCNAC-01 fitted to a 15 liter steel reservoir.
Order example:
PumpBCN-AC-01BCN-AC-02BCN-AC-11BCN-AC-12BCN-AC-21BCN-AC-22BCH-CT-11BCH-CT-12BCH-CT-21BCH-CT-22
12345611122122
Progressive Line
BC-12
Description
Specifications
Central pumping Station ECB-AC-33-TP28-A
Example Order:
Lubricant dosing units suitable for either grease or oil. Use when a componentrequires between 2,3 and 30 cubic centimeters of lubricant. Two versionsavailable.
ECB-AC-3 3 2,30-15 cm3
2,30-30 cm3ECB-AC-3 4
Model Flow
Central pumping StationMod. ECB-AC-3
Requirement Code
34
ECB-AC-3 - TP
2,30 - 15 cm3
2,30 - 30 cm3
Regulable DischargeAB
GrasaAceite
Lubricant28303234
Dep. Mod.28Dep. Mod.30Dep. Mod.32Dep. Mod.34
Progressive Line
BC-13
"L"
182
NPSF 1/8"
VALVE OF ADJUSTABLE RELIEF
Description
Specifications
Requirement Code
A motorised radial piston pump. Suitable for operating with oil and used in single line pro-gressive and single line parallel lubrication systems.This pump can be combined with different types of lubricant reservoirs and used in themachine tool and other related industries requiring oil lubrication.The robust construction and quality assembly components of this unit makes it a highlyreliable pump.
Observation: according to the type of deposit to use this unit is identified with 2 models:: for depositsof 3 liters of capacity=BCE-JR-3. For deposit of 15 liters of capacity=BCE-JR-15. The only existent dif-ference among these two models is the height of its suction tube.
Deposit Size3 Litros
15 Litros3
15
BCE-JR
Electric PumpBCE-JR
Example Order: BCE-JR-3
Steel
mineral and sinthetic base oil
100 cm3/min.50 bar0,08 Kw. - 2800 r.p.m. 220/380V. - 50 Hz.
Material
FlowMax. Operation PressureMotor workingLubricant
Unique Line
Progressive Line
Pump Model
BCE-JR-3BCE-JR-15
Capac.3 Lts.
15 Lts.
“L”313470
Depósit
BC-14
Electric PumpBCE-JE
Requirement Code
Flow500 cm3/min.750 cm3/min.
500750
BCE-JE
Description
Specifications
A motorised gear pump. Suitable for operating with oil and used in single line pro-gressive and single line parallel lubrication systems.This pump can be combined with different types of lubricant reservoirs and used inthe machine tool and other related industries requiring oil lubrication.The robust construction and quality assembly components of this unit makes it ahighly reliable pump.
Steel
mineral and sinthetic base oil
500 cm3/min. / 750 cm3/min.50 bar1/8 Kw - 2800 r.p.m. 220/380V. - 50 Hz.
Material
FlowMax. Operation PressureMotor WorkingLubricant
Deposit Size3 Litros
15 Litros3
15
Example order: BC-JE-500-3
Unique Línea
Progressive Line
OBSERVATION: according to the depost type to use this unit is identified with 2 models: fordeposits 3 liters of capacity=BCE-JE-3. For I deposit of 15 liters of capacity=BCE-JE-15. Theonly existent difference among these two models is the height of its suction tube.
Pump model
BCE-JE-XXX-3BCE-JE-XXX-15
Capac.3 Lts.
15 Lts.
“L”333438
Depósit
BC-15
DescriptionThese central pumping stations are designed to operate in centralized single pro-gressive and single line parallel lubrication systems.Assembled on a transparant polycarbon reservoir with filler breather and lowlevel switch. These central pumping stations can be provided with BCE-JR orBCEJE pumps depending on the size of the lubrication system.
Specifications
Requirement Code
Unique LineCentral pumping Station
ECB-JE/JR-3
Pumping Unit Mod. PumpBCE-JR
BCE-JE 500BCE-JE 750
TypePISTONGEARSGEARS
Flow100 cm3/min500 cm3/min750 cm3/min
Max. Pressure50 bar50 bar50 bar
Material Policarbonato REVEALEDepósit
Capacity 3 Litros
low level indicatorLubricant Charge entrance
BCE-JR 100 cm3/mBCE-JE 500 cm3/mBCE-JE 750 cm3/m
Pump flow100500750
BCE-JRBCE-JE 500BCE-JE 750
Bomb TypeJRJEJE
ECB - 3 -Central pumping stations BCE-JE with polycarbon reservoir 3 liters capacity,and with 500 cm3/min pump.
ECB-JE-3-500Example order:
Central Pumping StationECB-JE/JR-15/25
DescriptionPumping Station with various pumps fitted to a common reservoir operating simultaneously.These central pumping stations can operate in Unique Line or Single line Progressive systems;Pumps could be BCE-JR or BCE-JE.The steel reservoir is normally with low level electric, filler / breather and visual level indicator.. Thesolid and robust construction makes it a reliable assembly capable of operating in any indstrial type ofapplications.
BC-16
Pumping units Mod. pumpBCE-JR
BCE-JE 500BCE-JE 750
OperationPistonGearsGears
Flow100 cm3/min500 cm3/min750 cm3/min
Max.Pressure50 bar50 bar50 bar
Specifications
Bomb TypeBCE-JRBCE-JE
JRJE
DepositCapacity15 Litres25 Litres
1525
Bomb Quantity1 pump2 pumps3 pumps
123
BCE-JR 100 cm3/mBCE-JE 500 cm3/mBCE-JE 750 cm3/m
Bomb Flow100500750
Requirement Code
ECB
Central Pumping Station consisting of a BCE-JE with 25 liters tyreservoir, pump discharge 500 cm3/min and 3 pumps assem-bled on the reservoir.
ECB-JE-500-25-3Example Order:
Unique Line
Progressive Line
Central Pumping StationECB-JE-LS
BC-17
Pumping Units Mod.PumpBCE-JE 500BCE-JE 750
TypeGearsGears
Flow500 cm3/min750 cm3/min
Máx.Pressure50 bar50 bar
Specificacions
Pump TypeBCE-JE JE
DepositCapacity
15 Litros25 Litros
3 Litros
15253
BCE-JE 500 cm3/mBCE-JE 750 cm3/m
Pump Flow500750
Requirement Code
ECB
Unique Line
Dimensiones GeneralesGeneral dimensions of Pumping Centrals with policarbonate deposit
General Dimensions of Pumping Centrals with metallic deposit
DescriptionA Central Pumping Station designed to operatein unique centralized lubrication systems usinglubricants that needs agitation.Mounted on a transparent polycarbonate or asteel reservoir with filler / breather and low levelswitch.These sets are provided with a special agitatorwhen it is used with oils that contains preserva-tives in suspension.
BC-18
DescriptionThese Central Pumping Stations are designed to operate with grease or oil in single lineprogressive and dualine systems.Driven by a 12 or 24 volts DC electric motor these pumps can be fitted with 1 to 3 pumpingelements.The pumping elements are operated by an eccentric.Acrylic reservoirs for oil or grease with different capacities can be assembled on the pumpunit to satisfy the lubricant consuption demands. These reservoirs can also be fitted with lowlevel electric switches designed to operate with oil or grease. These pumps are suitable forinstallation on mobile machinery.
Specifications
Central Pumping StationECB-EM
CAST ALUMINIUM
OF 1 TO 3250 bar
Material body
Pumping elementsMax. operation Pressure
5 - 5,72 cm3/min.6 - 8,00 cm3/min.7 - 11,44 cm3/min.
Mod. CC-2000Mod. CC-2200
Fixed Flow Derby Control Switchboard
12 ó 24 Volts. - 40 RPMMotor
1 Pumping2 Pumping3 Pumping
Cant. Bombines Caudal Bombines Capac. Dep. Lubric.
123
LubricantGrease
OilAB
12 Vcc24 Vcc
12
5,72 cm3/min.8,00 cm3/min.
11,44 cm3/min.
567
2 Kg/2 Lts.5 Kg/5 Lts.7 Kg/7 Lts.
257
Part Numbers
ECB-EMEj. 1: ECB-EM-3(6-7-6)7-A-2ECB-EM with motor work of 24 Volts, 2 bombines ofcharacterisitc 6 and 1 bombín of characteristic 7 andwith a 7 Kg. deposit capacity for grease.
Ej. 2: ECB-EM-2(6-5)5-A-2ECB-EM with motor work of 24 Volts , 1 bombínofcharacterisitc 6, 1 bombín of characterisitc 5 and witha 5 Kg. deposit capacity for grease.
Example :
Unique Line
Progressive Line
( )- -
EM-3130-RRequirement Code reparation STD kit
060228
CONTROL BOARD
BC-19
Central Pumping StationECB-EF
1 Pumping2 Pumping3 Pumping
Cant. Bombines Capac. Dep. Lubric.
123
LubricantGrease
OilAB
2 Kg/2 Lts.5 Kg/5 Lts.7 Kg/7 Lts.
257
Part Numbers
ECB-EFEj.1: ECB-EF-3(7-6-7)7-A
Ej.2: ECB-EF-1(6)5-A
Example:
DescriptionThese Central Pumping Stations are designed to operate with grease or oil in single line progressive anddualine systems.Driven by an AC electric motor these pumps can be fitted with 1 to 3 pumping elements.The pumping elementsare operated by an eccentric.Acrylic reservoirs for oil or grease with different capacities can be assembled on the pump unit to satisfy thelubricant consuption demands. These reservoirs can also be fitted with low level electric switches designed tooperate with oil or grease. These pumps are suitable for installation on mobile machinery.
Specifications
CAST ALUMINIUM
OF 1 TO 3250 bar
Body Material
Pumping ElementsMax. Operation pressure
5 - 2,00 cm3/min.6 - 2,80 cm3/min.7 - 4,00cm3/min.
Mod. CC-3000-FFixed Flow DerbyControlSwitchboard
0.07 Kw. - 220/380V - 1400 RPM - 50 Hz.Motor
Caudal Bombines5 - 2,00 cm3/min.6 - 2,80 cm3/min.7 - 4,00 cm3/min.
567
Double Line
Progressive Line
( )- -E.g. 1: ECB-EF-3(7-6-7)7A ECB-EF is a central pump-ing station with motor of working of 220 V, with 2 der-bies of characteristic 7 and 1 derby of characteristic 6and a deposit of 7 kg of grease capacity.
E.g. 2: ECB-EF-1(6)5-TO ECB-EF is a central pumping station with motor of work-ing of 220 V, with 1 derby of characteristic 6 and adeposit of 5 kg. of grease capacity.
EF-3530-RRequirement Code reparation STD kit
Reducer 1:100
060228
BC-20
Pumping elementEBC-VA
0,143 cm3
0,200 cm3
0,286 cm3
Discharge
Dosage
567
Relief110 bar250 bar
12
Requirement Code
EBC-VA
DescriptionEBC-VA pumping element is the pumping elements used in ECB-EM and ECB-EFpumping stations. They are provided internally with a relief valve that preventsdamage to the pump in case of system blockage.
Specifications
Oil or Grease up to NLGI2 grade
de 0,143 a 0,286 cm3
250 bar
Lubricant
DischargeMax.Pressure
from 110 to 250 barRelief Pressure
Double Line
Progressive Line
BC-21
Air operated drum pumps. 4:1 Ratio for oil and 50:1 Ratio for grease. Thesepumps can be assembled to suit different types of lubricant containers.Pumpsare mounted with drum covers for grease and bung adaptors for oil.The air motors are corrosion resistant with double trigger mechanism, anduses a high quality packing assembly to prevent lubricant entering the airmotor. The pumping mechanism is manufactured from special materialensuring long life.
Description
Pneumatic pumpMod. BCN-219/221
Specificacions
Can 20 Kg.Can 60 Kg.
Tambor 180 Kg.Can 25 Kg.
19202125
LubricantGrease
OilAB
Requirement code
BCN-2
Example Order:
Requirement code for reparation STD kit AccesoriesD/C and F/P
Bung AdaptorTPN
PUMP MODELBCN-219-ABCN-220-ABCN-221-ABCN-225-ABCN-219-BBCN-220-BBCN-221-BBCN-225-B
KITCODE219-249220-249221-249225-249219-251220-251221-251225-251
1) BCN-220-A-TPPump with lid p/grease (can 60 Kg.)
BCN-221-AGrease Pump
BCN-221-BBCN-219-ABCN-220-ABCN-225-A
BCN-219-BBCN-220-BBCN-225-B
Oil Pump
PUMP MODELBCN-219-ABCN-220-ABCN-221-ABCN-225-ABCN-219-BBCN-220-BBCN-221-BBCN-225-B
Prefix (A): GreasePrefix(B): Oil
D419590872549391693921598
E7469071171876680
982.51210.5887.5
Máx: 12 bar - Mín: 2 bar
Flow / cycleFlow / min.
GREASE “A” OIL “B”31 cm3/ciclo6,5 lts./min.
4:1
4,4 g/ciclo1,2 Kg./min.
50:1
Lubricant
Pressure RelationshipAir operation pressure
BC-22
Description
Pneumatic PumpModel BCN 85
Specificacions
Air operated drum pumps. 6:1 Ratio for oil and 40:1 / 75:1 Ratio for grease.These pumps can be assembled to suit different types of lubricant containers.Pumps are mounted with drum covers for grease and bung adaptors for oil.The air motors are corrosion resistant with double trigger mechanism, anduses a high quality packing assembly to prevent lubricant entering the airmotor. The pumping mechanism is manufactured from special materialensuring long life.
Rel. 40:1 Grease
Rel. 6:1 Aceite
Rel. 75:1 Grasa
85-A85-B
86-A
AccesoriesD/C and F/P
Bung AdaptorTPN
Requirement Code
BCN1) BCN-85-A-TPPUMP FOR FAT WITH LID AND PLATE
Order example:
Máx: 12 bar - Mín: 2 bar
Flow / cycleFlow/ min.
GREASE “A” OIL “B”140 cm3/ciclo22,3 g/ciclo 22,3 g/ciclo
20 lts./min.9 kg./min. 5,7 kg./min.
6:140:1 75:1
Lubricant
Pressure RelationshipAir operation pressure
PUMP MODEL-BCN-85-ABCN-85-BBCN-86-A
CODIGO KIT13BCN-85-K
13BCN-85-B-K13BCN-86-K
Requirement Code of reparation STD kit Model Pump
BC-23
This pump is designed to boost the pressure when the lubricant is pumpedover long distances. The booster pump is pipe mounted and driven by theBCN-85 air motor. By regulating the air pressue the booster pumps increasesthe incoming pressure of the lubricant to the required pressure downstream ofthe pump. The pumping distance of the lubricant from the storage tank, thestorage tank head, the size of the transfer line and the type off lubricant useddetermines the numberbooster pumps in a system.
Description
Requirement Code
Pneumatic PumpBooster
Specificationes
Maximun Delivery Packing inlet and outlet
3,8 Lts/ min. Poliuretane 3” NPTF
BCN-R-80
BC-24
Description
Specifications
Variable Flow Pump Mod. BCE CV
One pumptwo pumps
12
Flow14 Lts./hour28 Lts./hour
710
Requirement Code
BCE-CV
An adjustable positive displacement pumping unit used more specifically in theearth gas industry. Each steel housing can be fitted with up to two pumpingunits. The pumping units are fitted with a built in relief valve and the flow ratescan easily be adjusted to suit.
Model 7 14 litros/hour28 litros/hour
980 RPM980 RPM
560 bar560 barModel 10
Pump Max. Flow Max. revolutions Max. op. pressure
Example Order: Pump Cirval BCE-CV-1-20
Progressive Line
BC-25
Description
LCC lubricatorCABLE Mod. LCC
Dualine
Specifications
LCC cable lubricator is a temporary installed steel cable lubricator. The designallows the unit to be installed in any position. It is however recommended thatthe unit be installed next to the pulleys where the cable has little movement.We reccommend installing the unit for one cycle of the wire rope and thenremove. clean and store the unit until lubrication is required again.Operation: From a motorised, pneumatic or manual pumping station the lubri-cant is discharged and injected into the cable lubricator.The cable is lubricated when passing through this lubricator.Excess of lubricant is removed by a brush with nylon threads maintaining anuniform layer of lubricant.The cable lubricator, due to its split body allows assembly onto the cable withina few minutes. Securing the equipment is done with flexible supports (chains)or rigid supports (articulate arms) embedded to secured cables.Typical applications are harbour cranes, winders, bridges, hoist cranes, lifts andmany more.
Cable
Diá
met
re 1/2”3/4”
1”1 7/8”
Requirement CodeExample order.
A B
CC
Ø19
1/4'
'BS
P
K
OIL INLET
G
H D
EJ
F
Cast Aluminium
PoliuretaneSteel with thermic treatmetOil or grease
Body
Buje guíaRodillo guíasLubricant
LCC
AB
GreaseOil
Lubricant
LCC-3/4”-A
CABLEØ1/2’’Ø3/4’’Ø1’’
Ø1 7/8’’
A
220
425
B
100
256
C
50
128
D
10
19
E
109
185
F
8
14
G
72
130
H
97
198
I
65
130
J
92
156
K
1
1
Accesories
A-01
ACCESORIES"B
"E
xag.
E/C
"C"
Ø"A
"(N
PS
F)
Combination nut and sleeve - CU-81
MODEL
CU-81-AA1CU-81-B1CU-81-B2CU-81-D3
Material: Zinc Coated Steel
Material: Zinc Coated Steel
Material: Zinc Coated Steel
ø TUBE
4,86,46,49,5
øA
1/8”1/8”1/4”3/8”
B
11,111,114,317,5
C
21,41924
25,4
C`(NOMINAL)
C
B(E
XA
G. E
/C)
ØA
(NP
TF)
CONNECTORMODEL CU-81
Tube Union - CU-84
MODEL
CU-84-ACU-84-BCU-84-D
ø TUBE
4,86,49,5
øA
1/8”1/8”3/8”
B
12,714,320,6
C
25,427
38,1
C’
514767
C
B(E
XAG
. E/C
)
ØA
(NPT
F)
C`(NOMINAL)
CONNECTORMODEL CU-81
Straight connector - CU-83
MODEL
CU-83-A1CU-83-A2CU-83-B0CU-83-B1CU-83-B2CU-83-B3CU-83-D1CU-83-D2CU-83-D3CU-83-D4
ø TUBE
4,84,86,46,46,46,49,59,59,59,5
øA
1/8”1/4”
1/16”1/8”1/4”3/8”1/8”1/4”3/8”1/8”
B
12,714,312,712,7161919191919
C
17,515,521,41919
17,528292558
C’
28262928282844444070
A-02
ACCESORIES
E`(NOMINAL)
E
ØB
(NPS
F)
ØA(NPTF)
D
C
ELBOW 90º - CU-87
STEEL STREET ELBOW 45º - CU-1103
MODEL
CU-87-A1CU-87-A2CU-87-B1CU-87-B2CU-87-B3CU-87-D1CU-87-D2CU-87-D3CU-87-D4
ø TUBE
4,84,86,46,46,49,59,59,59,5
øA
1/8”1/4”1/8”1/4”3/8”1/8”1/4”3/8”1/2”
øB
1/8”1/8”1/4”1/4”1/4”3/8”3/8”3/8”1/2”
C
12,71417172121212125
D
22222222
24,525
24,524,530
E
151516161620212124
E’
25,428,528,528,531,836,536,536,5
-
MODEL
CU-1103-ACU-1103-B
øA
1/8”1/4”
B
25,434
C
12,717,5
Material: Zinc Coated Steel
Material: Zinc Coated Steel
B
C
ØA(NPTF)
ØA(NPSF)
A-03
ACCESORIES
ELBOW 90º - CU-1104
STEEL REDUCING STREET ELBOW 90º - CU-1105
MODEL
CU-1104-ACU-1104-B
øA
1/8”1/4”
B
23,834,5
C
12,717,5
MODEL
CU-1105-ACU-1105-B
A
1/8”1/4”
B
1/4”3/8”
C
17,522
D
8,611
E
3038
F
12,816
Material: Zinc Coated Steel
Material: Zinc Coated Steel
C
B
ØA(NPSF)
ØA
(NPS
F)
A-04
ACCESORIES
AC
B(E
XA
G.E
/C)
ØNPTF
ØNPSF
C
D(E
XA
G.E
/C)
ØA
(NP
TF)
ØB
(NP
TF)
REDUCING BUSH- CU-104
MODEL
CU-104-B1CU-104-C1CU-104-C2CU-104-D1CU-104-D2CU-104-D3CU-104-E1CU-104-E2CU-104-E3CU-104-E4CU-104-F2CU-104-F3CU-104-F4CU-104-F5CU-104-H4
NPTF
1/4”3/8”3/8”1/2”1/2”1/2”3/4”3/4”3/4”3/4”1”1”1”1”
1 1/2”
NPSF
1/8”1/8”1/4”1/8”1/4”3/8”1/8”1/4”3/8”1/2”1/4”3/8”1/2”3/4”1/2”
A
161618182020202222222228282830
B
161919252525313131313838383845
C
111212141414151515152020202020
MODEL
CU-151-11CU-151-21CU-151-22CU-151-32CU-151-33
øA
1/8”1/4”1/4”3/8”3/8”
øB
1/8”1/8”1/4”1/4”3/8”
C
2730353535
D
12,714,314,317,517,5
PIPE NIPPLES - CU-151
Material: Zinc Coated Steel
Material: Zinc Coated Steel
Material: Zinc Coated Steel
MODELCU-431 2-4CU-431 4-4CU-431 6-4CU-431 2-5CU-431 4-5CU-431 4-6CU-431 6-5CU-431 6-6CU-431 8-6CU-431 4-8CU-431 6-8CU-431 8-8CU-431 12-8CU-431 8-10CU-431 12-10CU-431 8-12CU-431 12-12CU-431 12-16CU-431 16-16CU-431 20-20CU-431 24-24
A313635313636353643393945474849525253586268
B141414141414141414171717171919222223232427
C101414101414141419141419191919191919242525
E12.714.324
14.314.316241922212122
28.624
28.628.628.635354351
D7/16”7/16”7/16”1/2”1/2”
9/16”1/2”
9/16”9/16”3/4”3/4”3/4”3/4”7/8”7/8”
1 1/16”1 1/16”1 5/16”1 5/16”1 5/8”1 7/8”
G4.54.5
10.566
7.57.57.5137
101010121313
15.515.5213238
F1/8”1/4”3/8”1/8”1/4”1/4”3/8”3/8”1/2”1/4”3/8”1/2”3/4”1/2”3/4”1/2”3/4”3/4”1”
1 1/4”1 1/2”
ADAPTOR CU-431
A-05
ACCESORIES
B
C
D(E
XA
G. E
/C)
ØA
(NP
TF)
MODEL
CU-86-ACU-86-BCU-86-CCU-86-D
øA
1/8”1/4”3/8”1/2”
B
14,214,217,519
C
99
10,511
D
11,114,217,522,2
PLUG - CU-86
ØA
(NP
TF)
C(E
XAG
.E/C
)
B
MODEL
CU-119-A1CU-119-ACU-119-BCU-119-CCU-119-DCU-119-E
øA
1/16”1/8”1/4”3/8”1/2”3/4”
B
68
11,513
14,516
C
44,86,58
9,514,3
MODEL
CU-2986-ACU-2986-BCU-2986-D
øA
1/8”1/4”3/8”
B
151718
C
111314
D
11,114,317,5
PLUG - CU-119
D(E
XA
G.E
/C)
BC
ØA
(NP
SF)
PLUG - CU-2986
Material: Zinc Coated Steel
Material: Zinc Coated Steel
Material: Zinc Coated Steel
A-06
ACCESORIES
D
E
FG
ØH
B
ØA(NPSF)
ØA
(NP
SF)
C
Anchor Block - CU-1927
MODEL
CU-1927-ACU-1927-BCU-1927-CCU-1927-D
øA
1/8”1/4”3/8”1/2”
B
16203238
C
3544,55454
D
22353838
E
1217,52222
F
1922
25,431
G
89,5
12,713
H
67
8,58,5
Material: Zinc Coated Steel
C
B
D(E
XA
G.E
/C)
ØA
(NP
SF)
D(E
XA
G.E
/C)
Air Bleed - PC
MODEL
PC 1PC 3
øA
1/8”3/8”
B
14,530
C
1842
øD
1416
øD
12,717,1
ED
B C
ØA-TIP.(NPSF)
TEE - CU-137
MODEL
CU-137-ACU-137-BCU-137-CCU-137-D
øA
1/8”1/4”3/8”1/2”
B
28404261
C
14202030
D
14232424
E
21353539
Material: Zinc Coated Steel
Material: Brass
A-07
ACCESORIES
G
H
D
FE
JØ
A(N
PSF)
ØA(NPSF)ØL
I
ØA
(NPS
F)Ø
L
ØB(NPSF)
C
ØK
Dualine Tee - CU-1008
7.25
25.5
Ø8.
75N
PS
F 1/
8"
Ø11.25NPSF 1/4"
7.25 25.540
40
25
40
AGUJ.Ø5,5
CONNECTION BLOCK - CU-1080-B1
MODEL
CU-1008-BBCU-1008-DDCU-1008-DD1
øA
1/8”3/8”3/8”
øB
--
1/8”
C
51
63,5
D
40
57
E
16
23
F
14
20
G
22
32
H
8
11
I
17
21,5
J
22
31,5
øK
5,5
7
øL
6,5
9,7
Material: Zinc Coated Steel
Material: Zinc Coated Steel
A-08
ACCESORIES
11.113.2
NP
TF1/
8"
Relief Valve - CU-962-B
Relief Pressure: 0,07 a 0,35 bar
35
12,7
(EX
AG
.E/C
)
VALVE(STD)
1/8"
(NP
SF)
1/8"
(NP
SF)
Relief Valve - CU-1975-B1
Opening Pressure: 8 a 9 bar.
Relief Valve - CU-1997-B1
Opening Pressure: 8 a 9 bar.VALVE(STD)
1/8"
(NP
SF)
1/8"
(NP
SF)
35
12,7
(EX
AG
.E/C
)
A-09
ACCESORIES
Ø1/
8"(N
PS
F)
Ø1/
8"(N
PS
F)
12,7
(EX
AG
.E/C
)
66
01 02 03 04 05 06
Non Return Valve - CU-1987-A1Part ListPos.
123456
DescriptionBodyValveSpringAdjusting ScrewWasherConnector
Quantity111111
Opening Pressure: 8 a 10 bar.
61
1/4"
(NPT
F)
3/8"
(NPS
F)
19,1
(EXA
G.E
/C)
01 02 03 04 05
Non Return Valve - CU-887-D2Part ListPos.
12345
DescriptionConnectorWasherSpringBallBody
Qunatity11111
Opening Pressure: 5 a 7 bar.
38
Ø1/
4"(N
PS
F)
15,9
(EX
AG
.E/C
)
Ø1/
4"(N
PTF
)
1 2 3 4 5
Non Return Valve - CU-1087-B2Part ListPos.
12345
DescriptionBodySeat screwWasherBallSpring
Quantity11111
Opening Pressure: 3 a 5 bar.
15,9
(EXA
G.E
/C)
Ø1/
4"(N
PSF)
Ø1/
4"(N
PTF)
56
01 02 03 04 05 06 04 06 07
Non Return Valve - CU-2087-BParts ListPos.
1234567
DescriptionBodySeat screwWasherBallWasherSpringConnector
Quantity1112121
Opening Pressure: 8 a 10 bar.
A-10
ACCESORIES
Rotating Connector - CU-990
MODEL
CU-990-0CU-990-A
øA
1/16”1/8”
Max. Operating PressureMaximum RPM
100 bar100
Parts ListPos.
1234
DescirptionConnectorLocating RingSealBody
CodeCG-001CG-002CG-003CG-004
02 04 05 06 07
25,4
(EX
AG
.E/C
)
3853
79
19(E
XA
G.E
/C)
ØA
(NP
TF)
ØA(NPSF)
01 03
Rotating Connector - CU-989-T
MODEL
CU-989-5-TCU-989-6-TCU-989-7-T
øA
1/8”1/4”3/8”
RPM (Máx)
100100100
Parts ListPos.
1234567
DescriptionBodyInner BushSealLocating RingOuter BushLocating RingConnector
CódeCCO-001CCO-002CCO-003CCO-004CCO-005CCO-006CCO-007
Max. Operating PressureMaximum RPM
100 bar100
56
Exag
. e/c
. 32
NPS
F Ø
A
06 05 04 03 02 0107
Rotating Connector - CU-994Parts ListPos.
1234567
DescriptionConnectorBodyPackingBearingDividerLocating RingCover
CódeCC-001CC-002CC-003CC-004CC-005CC-006CC-007
Max. Operating PressurewMaximum RPM
100 bar1500
MODEL
CU-994-5CU-994-6
øA
1/8”1/4”
Ø1/8"(NPSF)
ØA
(NPT
F)
11,5
27
Ø30 19
,1(E
XAG
.E/C
)
11.5
A-11
ACCESORIES
60°
12,7
(EX
AG
.E/C
)
Ø1/
8" (N
PS
F) Ø1
15.5
Nozzle - PGC-1
Brushes - CLC-C
2822
20
9
Aguj. Ø6Pasante 30
18
15A
7Ø1/8" (NPSF)Ø1/8" (NPSF)
15
1830
7
CLC-P20
Flat Plastic Brushes - CLC-P
Code
Bodyø 16ø 28
CLC-C
1628
FibresStandardStainless
12
Code
PGC-1
Requirement Code
BodyAncho = 20Ancho = 50Ancho = 80
Ancho = 160
CLC-P
Material: Nylon
205080
160
ModelCLC-P50CLC-P80
CLC-P160
A5080
160
A-12
ACCESORIES
Filter TF-0
Filtre TF-1 with mechanical indicator
TF-0 filters are used in oil or grease supply lines. Theyretain foreign particles in lubricant thus preventing dam-ageto component in the lubrication systems.They include filter elements of 100u or 250.Units are fitted with a by-pass valve and a pressuregauge.
TF-1 filters are used in oil or grease supply lines. Theyretain foreign particles in lubricant thus preventing dam-age to component in the lubrication systems.They include filter elements of 100u or 250.Units are fitted with a by-pass valve and a pressuregauge.A mechanical indicator on these units can be used toactivate an electrical switch for dirty filter alarm.
Max. operating pressureMicronajeDifferencian pressure
70 bar100 ó 250µ
3 bar
Max. operating pressureMicronajeDifferencian pressure
70 bar100 ó 250µ
3 bar
Filtre TF-11TF-11 filter to be used in oil supply lines. They retain foreignparticles in lubricant and prevent damage to the lubrication sys-tem components.They are available with elements rated 10, 25u or 40u. Theyalso include an internal by-pass valve.A mechanical indicator on these units can be used to activatean electrical switch for dirty filter alarm.The TF-11-WR desgn has a filter element that it retains themoisture that may be present in the oil.
*Model TF-11-WR has a fitrant elementwhich retains the oil humidity.
Max. Work PressureMicronajeDiferencial pressure
70 bar10, 25 ó 40µ
3 bar
MODELTF-11-10TF-11-25TF-11-40TF-11-WR
Filtration Rate10 µ25 µ40 µRecover Humidity
A-13
ACCESSORIES
Filter TF-2
Line Filter FCSL-3/8
TF-2 duplex filters are used in oil or grease sup-ply lines.They retain foreign particles in lubricant thuspreventing damage to components in the lubri-cation systems.They include filter elements of 100u or 250.Units are fitted with a filter selection valve, a by-pass valve and pressure gauges.A mechanical indicator on these units can beused to activate an electrical switch for dirty fil-ter alarm.
FCSL line filters are used in oil or grease supply lines.They retain foreign particles in lubricant thus preventingdamage to components in the lubrication systems.They include filter elements of 100u or 250.A mechanical indicator on these units can be used toactivate an electrical switch for dirty filter alarm.Maximum operating pressure 350 Bar.
Max. Operating PressureMicronajeDiferencial pressure
70 bar100 ó 250µ
3 bar
Max.Operating pressureMicronajeDiferencial Pressure
350 bar100 ó 250µ
3 bar
12012006
A-14
ACCESORIES
A
19
R=D
PLCH. 19x1,6
B
HOLES .Ø7,5
9.5
19
MODEL
CU-301-A1CU-301-B1CU-301-D1
øTube
3/16”1/4”3/8”
A
6,59,6
12,7
B
8,512,716
C
23,55
D
2,53
4,5
MODEL
CU-301-A2CU-301-A3CU-301-B2CU-301-B3CU-301-D2
øTube
3/16”(2)
3/16”(3)
1/4”(2)
1/4”(3)
3/8”(2)
A
6,56,59,69,6
12,7
B
13,5191922
25,5
C
22
3,53,55
D
2233
4,5
MODEL
CU-1301-A4CU-1301-A6CU-1301-B4CU-1301-B6CU-1301-D3
øTube
3/16”(4)
3/16”(6)
1/4”(4)
1/4”(6)
3/8”(3)
A
6,56,59,69,6
12,7
B
223232
44,535
C
-----
D
2233
4,5
Tube Clamps - CU-301
Tube Clamps - CU-1301
19B
9.5
C
A
HOLES .Ø7,5
R=D
PLCH. 19x1,6
A19
R=D
PLCH. 19x1,6
B
HOLES .Ø7,5
9.5
C
Material: Zinc Coated Steel
Material: Zinc Coated Steel
A-15
ACCESORIES
One Way Coupling CU-967
One Way Coupling CU-968
Flexible Coupling CU-969
Pos.123456789
DescriptionInput BodyCoupling BodyOutput BodySpacerSleeveSpringScrewScrewLocating Ring
Quantity111111111
Pos.12345
DescriptionInput BodyOutput BodySpiderScrewScrew
Qunatity11111
Pos.123456789
10
DenominaciónScrewSpringLocating RingClutchScrewInput BodyCoupling BodyBearlingSleeveOutput Body
Quantity1111111111
MODEL
CU-968-10CU-968-25
Pump
BCE-J10BCE-J25
Shaft size
ø 14ø 19
A-16
ACCESORIOS
Spray control valve VCCS-S1 / VCCS-S1-I
(with indicator)
Spray Manifold with nozzle CSMP
Spray Valve Assembly CU-922-C
MODEL
CSMP-1CSMP-2CSMP-3CSMP-4CSMP-5
A
386490116142
B
285480
106132
ACCESORIES
OutsideDiameter
Inches3/16”1/4”3/8”
mm.4,766,359,52
Wall Thickness
Inches0,0280,0300,030
mm.0,7110,7620,762
OperatingPressure
psi479138402560
kg/cm2
336269179
Weight
m/kg.14,069,496,05
Ib/pie0,0480,0710,111
MinimumBending Radiusmanual
3/4”1 1/8”2 5/8”
bender9/16”3/4”
1 1/8”
OutsideDiameter
Inches1/2”3/4”1”
1 1/2”2”
mm.21,326,733,448,360,3
Wall Thickness
Inches0,1090,1130,1330,1450,154
mm.2,772,873,383,683,91
OperatingPressure (20º)
psi37143071288621711857
kg/cm2
360215202152130
Weight
m/kg.1,2671,6892,5054,0545,444
Ib/pie0,7681,0241,5192,4593,302
Bundy TubingZinc Coated Steel Tube in accordance with ASTM-A 254 specification.
Schedule Piping in accordance with ASTM-A53 specification
Copper Tube
Nylon Tube
OutsideDiameter
Inches3/16”1/4”3/8”
mm.4,766,359,52
Wall Thickness
Inches0,0270,0270,027
mm.0,700,700,70
OperatingPressure (20º)
psi1309,6888,9541,9
kg/cm2
91,6762,2237,93
Weight
m/kg.0,0900,1100,180
Ib/pie0,0550,0660,109
OutsideDiameter
Inches3/16”1/4”3/8”
mm.4,766,359,52
Wall Thickness
Inches0,0230,0310,047
mm.0,600,801,20
OperatingPressure
psi600600600
kg/cm2
424242
Test Pressure(20º)
psi180018001800
kg/cm2
126126126
SPECIALDEVELOPMENTS
Container for 600kG of specialgrease
1
7
8 9
10 11
2 3
4 5
6
PneumaticBoosterPump
Automatic lubricators for moving grease points
PneumaticOperatedPump forgrease or oil
Pneumaticdevice forpumpingviscousproducts.
lubricator forsteel cables
Nickle platedValves andAccesories
Oil circulationsystem
Slinger sets for oil of visible drop.
Spray panels and lances for gear lubrication systems
Containers for provision of grease to bulk with supplypneumatic bomb. Capacity 1000 kg.
Our Company
INDUSTRIAL PLANT
Our industrial plant(floor) is located in Rosario's city,Province of Santa Fe, Republic Argentina.There we have 2000 m² where with machines of lastgeneration, produced(operated on) by highly qualifiedpersonnel, we produce all the components CIRVAL
Our Company
FOTO PACK OFPRODUCTS