出力線量測定のためのプラン作成手順書...2 | focus where it matters....
TRANSCRIPT
![Page 1: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/1.jpg)
出力線量測定のためのプラン作成手順書
エレクタ株式会社
![Page 2: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/2.jpg)
2 | Focus where it matters.
出力線量測定のためのプラン作成手順
1.新規プランを作成
2.Virtual Phantomを開く
3.処方線量の入力
4.Beam情報の入力
5.Calculation Propertiesの設定
6.線量計算、 MU値の確認
![Page 3: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/3.jpg)
3 | Focus where it matters.
1.Virtual Phantomを開くOpen Patientから「Virtual Phantom」を開きます
モデル納品時に登録されている「Virtual Phantom」を選択ください
![Page 4: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/4.jpg)
4 | Focus where it matters.
2. 新規プランの作成「New Plan」から「DEFAULT3D1BEAM」を選択します
「Treatment Unit」「Modality」「Algorithm」「Energy」、
Isocenter Locationは「Interest Point 1: 10cm」を選択してください
1つのプランに対しビームを1本作成します
![Page 5: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/5.jpg)
5 | Focus where it matters.
3.処方線量の入力左下の「Prescription」タブより
Rx Dose(cGy)に「100」、Number of Fractionsに「1」を入力します
![Page 6: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/6.jpg)
6 | Focus where it matters.
4.Beam情報の入力左下の「Beams」タブを選択し、「Geometry」より照射野サイズを作成します
Jawサイズを手入力し、BEVで確認してください10x10照射野の場合
![Page 7: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/7.jpg)
7 | Focus where it matters.
4.Beam情報の入力(Wedge)「Beams」タブ→「Treatment Aids」からWedgeを選択します
適切な方向にWedgeが挿入されているか、「Treatment Aid Display options」を変更し確認してください
60°Wedgeを挿入した場合(コリメータは90°に回転しています)
![Page 8: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/8.jpg)
8 | Focus where it matters.
5.Calculation Propertiesの設定「Calculation Properties」で計算条件の設定をします
「Force entire volume to be treated as water」にチェックをいれてください
Collapsed Cone Monte Carlo
※Monte Carloの場合は「Per Control Point」を選択
※「Grid Spacing」「Statistical
Uncertainty」はコミッショニング
等で使用している設定にそろえるのが望ましいです
![Page 9: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/9.jpg)
9 | Focus where it matters.
6.線量計算、 MU値の確認「Calculate」ボタンを押して線量計算をおこないます
照射MU値を「Prescription」タブより確認します
![Page 10: 出力線量測定のためのプラン作成手順書...2 | Focus where it matters. 出力線量測定のためのプラン作成手順 1.新規プランを作成 2.Virtual Phantomを開く](https://reader030.vdocuments.site/reader030/viewer/2022040917/5e90d0bf0844736f250cc58a/html5/thumbnails/10.jpg)