catalogue - premier techpremiertech.pt/pdf/catalogo(premier_tech)uk.pdf · description and...

CATALOGUE

2

Premier Tech Aqua is a business unit of Premier Tech, Portuguese experts in rotomoulding and advanced solutions for the treatment and storage of water and selective collection.

Our products are economical, long-lasting, fully certified and offer a wide range of solutions, including waterstorage tanks, septic tanks, SBR/MBR WWTPs, pumping stations, containers for selective collection, chemical toilets, retention basins solutions for the construction industry and much more!

Solutions for waterindustry professionals

4

Premier Tech - Product Line

5

TABLE OF CONTENTS

Introduction 3Surface tanks 6Underground tanks 10Rainwater Kit 14DSD dosing 16Tanks with DCT lid 17Septic tanks 18Anti-odour cartridge 28Biological activators 29Solido® SMART 30ECOFLO® - Compact coconut filter 34ECOPROCESS™ Solutions from 21 to 1000 EI 38ECOPROCESS™ Compact coconut filter 40WWTP 48Sampling box 54Screening box 55Hydrocarbon Separators - Class 1 56Grease Separators 58Pumping stations 62ECOIL- Used Oils Storage Tanks 70Battery cases 71Selective collection container 2500 72Boxline 74SuperFusto 76Drum support 77Retention basins 78Minibooth 80Mecaplast and Mecabi 82Fuel Tank IBC 84ADBLUE Tank - IBC 86

6

SURFACE TANKSHorizontal and Vertical

Description and characteristics of surface models:• Manufactured in High-Density Polyethylene - HDPE

• Available in horizontal and vertical models with storage volumes from 500 to 20,000 L.

• Access to the interior through lid on top.

• Easy assembly on smooth, flat surface.

• Sustainable and low weight; long-lasting; food quality and anti-UV treatment; rot-proof; corrosion-proof; easy to clean.

• Inlets and outlets can be placed in upper and lower areas for pipe connections.

•Lids available with security locks.

Use:• Horizontal tanks in HDPE for storage of water and other liquids (Contact us to verify compatibility).

• Rainwater collection model is equipped with an input filter, suction with anti-return valve and float, antiturbulence discharge, upper discharge with animal anti-intrusion, etc.

• Tanks can be reinforced for specific applications.

7

Horizontal TanksRef.

DHS500

DHS200

DHS2000

DHS1000

DHS300

DHS3000

DHS5000

Volume (L)

500

200

2000

1000

300

3000

5000

Diameter (mm)

750

580

1350

940

580

1520

1840

Height (mm)Lengh (mm)

830

650

1360

1250

910

1665

1050

650

1565

1865

1450

1320

1945

2210

Lid (mm)

ø200

ø270

ø400

ø400

ø270

ø400

ø400

8

SURFACE TANKSHorizontal and Vertical

Puffo Vertical TanksRef. Volume (L) Diameter (mm) Height (mm)Lenght (mm) Lid (mm)

DVB3000DVB3500DVB4500DVB5000DVB6500DVB7500DVB10000

30003500450050006500750010000

1700170017002068206820682068

1728-197824781822232226523422

------

ø400ø400ø400ø400ø400ø400ø400

Tall Vertical TanksRef.

DVA500

DVA2000DVA1000

DVA3500DVA4000

Volume (L)

500

20001000

35004000

Diameter (mm)

910

1350950

13001500

Height (mm)Lenght (mm)

910

1950

-

-1600

27002400

-

--

Lid (mm)

ø400

ø400ø400

ø400ø400

Puffo Short Vertical TanksRef.

DVBB3000

DVBB4500DVBB10000

DVBB3500

Volume (L)

3000

450010000

3500

Diameter (mm)

2068

20682400

2068

Height (mm)Lenght (mm)

1200

16202525

-

--

1340-

Lid (mm)

ø400

ø400ø600

ø400

9

Ribbed Vertical Tanks Ref.

DVBR6000

DVBR16000DVBR11000

DVBR21000

Volume(L)

6000

1600011000

21000

Diameter(mm)

2320

23202320

2320

Height(mm)

Lenght(mm)

1840

4250

-

-3100

5470

-

-

Lid(mm)

ø400

ø400ø400

ø400

Threaded or flanged fittings for liquid inlet and outlet

Access stairs to the lid with guardrails

Tank level gauge d

External Retention Basin

Leak viewer

Optional

d

ec

e

e

d

c

b

a

b a

Puffo Vertical Tanks

Ribbed Vertical Tanks Ribbed

Vertical Tanks

Puffo Short Vertical Tanks

10

NDERGROUND TANKS

Description and characteristics of underground models:• Manufactured in High-Density Polyethylene - HDPE

• Volumes from 5,000 to 75,000 L.

• Access to the interior through lid on top.

• Easy transportation and installation.

• Sustainable and low weight; long-lasting; food quality and anti-UV treatment; rot-proof; corrosion-proof; easy to clean.

• Inlets and outlets can be placed in upper and lower areas for pipe connections.

• Lids available with security locks.

Use:• Horizontal tanks in HDPE for storage of water and other liquids (Contact us to verify compatibility).

• Rainwater collection model is equipped with an input filter, suction with anti-return valve and float, antiturbulence discharge, upper discharge with animal anti-intrusion, etc.

• Tanks can be reinforced for specific applications.

12

UNDERGROUND TANKS

13

High storage capacity horizontal underground tankRef. Volume (L) Diameter (mm) Height (mm)Length (mm) Lid (mm)

DHE8000

DHE6000

DHE5000

DHE15000

DHE35000

DHE55000

DHE75000

DHE12000

DHE10000

DHE30000

DHE50000

DHE70000

DHE20000

DHE40000

DHE60000

DHE25000

DHE45000

DHE65000

8000

6000

5000

15000

35000

55000

75000

12000

10000

30000

50000

70000

20000

40000

60000

25000

45000

65000

2050

2050

2320

2320

2320

2320

2320

2050

2320

2320

2320

2320

2320

2320

2320

2320

2320

2320

2130

2140

2460

2460

2460

2460

2460

3420

2740

2020

4580

9200

14320

19440

2130

2460

2460

2460

2460

2460

2460

2460

2400

2460

2460

4780

3300

7920

13040

18160

5360

10480

15600

6640

11760

17880

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

DHE5000

DHE4000

DHE3000

DHE2000

4000

5000

3000

2000

1660

1860

1510

1510

1680

1890

1630

1630

2460

2470

2375

1725

ø400

ø400

ø400

ø400

14

RAiNwATER KiT

Rainwater Recovery Model1 - Inlet / drainage pipe (DN 110)

2 - Dual filtration stainless steel grid

3 - 1” Pump connection

4 - Overflow siphon with anti-rodent net (Dn 110)(Dn 110)

5 - Suction hose with float and anti-return valve 6 - Spout with anti-turbulence system

GD11 pumping and compensation set1 - 60 L tank

2 - 1” main water supply with valve and float

3 - JI132M electric pump -1 KW, 220 V, 6,6 A, 50 Hz

4 - 1” water outlet pump

5 - Pump suction pipe

16

DSD DOSiNG TANKSDSD

Description and characteristics:Vertical tanks constructed of High-Density Polyethylene (HDPE) with UV resistance additive, with volumes of 100 to 1250 L.

HDPE is a rot-resistant, long-lasting material highly resistant to harmful chemicals.

Interior walls have smooth surfaces for easy cleaning and prevention of aggregation and accumulation of debris.

Low weight for easy transport and better handling.

Equipped with support bases on top of the tank for installation of dosing pumps or vertical axis stirrers.

Ease of placement for ducts through walls/flanges for connection of tubing.

Ref.

DSD100

DSD50

DSD300

DSD1250

DSD200

DSD500

Volume (L)

100

50

300

1250

200

500

Diameter (mm)

730

680

1190

1600

1020

1300

height (mm)Length (mm)

-

-

-

-

500

610

1150

550

750

360

-

-

Lid (mm)

ø125

ø125

ø125

ø400

ø125

ø220

17

Description and characteristics:Vertical tanks constructed of High-Density Polyethylene (HDPE) with UV resistance additive, available in volumes from 20 to 2,000 L.

HDPE is a rot-resistant, long-lasting material highly resistant to harmful chemicals.

Interior walls have smooth surfaces for easy cleaning and prevention of aggregation and accumulation of debris.

Low weight for easy transport and better handling. Fully opening circular lid.

Ease of placement for ducts through walls/flanges for connection of tubing.

Ref. Volume (L) Diameter (mm) Height (mm)Length (mm) Lid (mm)

DTC20

DTC100

DTC1100

DTC300

DTCFI1200

DTC50

DTC500

DTC200

DTC2000

20

100

1100

300

1200

50

500

200

2000

290

460

1100

610

1100

360

820

570

1350

300

700

1400

1070

1330

-

-

-

-

-

560

1140

980

1620

-

-

-

-

ø300

ø480

ø1120

ø630

ø1120

ø380

ø840

ø590

ø1370

DCT TANKS wiTH LiDSDCT

18

SEPTiC TANKS

Description and characteristics of septic tank models:Septic tanks are domestic waste water treatment devices, which use a combination of settling and anaerobic digestion to achieve a significant reduction of the pollution load.

Made of high density polyethylene, they are durable and resistant to harmful chemicals. The interior walls have smooth surfaces for easy cleaning and prevention of aggregation and accumulation of debris. Low weight for easy transport and better handling.

Should be installed in areas where there is no waste water drainage system.• Ideal for installation in soil that is difficult to excavate or where groundwater levels are high.

• Recommended for use in:

- Houses, condos, small lots, etc.

• Provides high-quality final treated effluent that seeps into the ground through sink wells or seepage trenches.

20

SEPTiC TANKS Millenium Horizontal Septic Tanks with Pre-filter

Ref.Volume

(L)Inhab.

Eq.Diameter

(mm)Height(mm)

Tubing(mm)

Length(mm)

Lid(mm)

FHC20000

FHC40000

FHC60000FHC65000

FHC70000

FHC75000

FHC15000

FHC12000

FHC10000

FHC8000

FHC6000

FHC5000

FHC4000

FHC3000

FHC2000

FHC35000

FHC55000

FHC25000

FHC45000

FHC30000

FHC50000

20000 100

40000 200

60000 300

65000 325

70000 350

75000 375

15000

12000

10000

8000

6000

5000

4000

3000

2000

75

60

50

40

30

25

20

15

10

35000 175

55000 275

25000 125

45000 225

30000 150

50000 250

2320

2320

2320

2320

2320

2320

2320

2130

2340

2130

2140

1860

1660

1510

1510

2320

2320

2320

2320

2320

2320

2460 DN160

2460 DN160

2460 DN160

2400 DN160

2460 DN160

2460 DN160

5360

10480

15600

17880

18160

19440

2460

2050

2460

2050

2050

1890

1680

1630

1630

DN160

DN160

DN160

DN110

DN110

DN110

DN110

DN110

DN110

2460 DN160

2460 DN160

2460 DN160

2460 DN160

2460 DN160

2460 DN160

4580

4780

3300

3420

2740

2470

2460

2375

1725

9200

14320

6640

11760

7920

13040

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø600

ø400

ø400

ø400

ø400

ø600

ø600

ø600

ø600

ø600

ø600

21

Safety Guillotine Avoids effluent spills when removing the filter for cleaning

Manhole access with a locking mechanism for safe entry

Greater rigidity due to undulation

Vertical reinforcements at the top

Great performance and easy to clean

Lamelar PF17 Pre-filter

Chicane Pre-filter

MARKED

EUROPEAN STANDARD

EN 12566-1

22

SEPTiC TANKS

Horizontal Septic Tank with Pre-Filter Ref.

Volume(L)

Inhab.Eq.

Diameter (mm)

Height(mm)

Tubing(mm)

Lenght(mm)

Lid(mm)

FHC1000 1000 5 940 1020 DN1101450 ø400

23

Vertical Septic Tank with Pre-FilterRef.

Volume(L)

Inhab.Eq.

Diameter(mm)

Height(mm)

Tubing(mm)

Lenght(mm)

Lid(mm)

FVC1000

FVC2000

FVC6000

FVC1250

FVC5000

FVC3500

FVC11000

FVC4000

FVC16000

1000 5

2000 10

6000 30

1250 6

5000 25

3500 16

11000 55

4000 20

16000 80

940

1350

2400

1150

2068

1310

2400

1500

2400

1600 DN110

1950 DN110

1900 DN160

-

-

-

1600 DN110

1822 DN110

2700 DN110

3180 DN160

2400 DN110

4460 DN160

-

-

-

-

-

-

ø400

ø400

ø400

ø400

ø400

ø400

ø400

ø400

ø400

24

COMPACT SEPTiC TANK

Description and characteristics:Compact Septic Tanks, also called biological septic tanks, are domestic waste water treatment devices in which a combination of settling with anaerobic digestion and additional aerobic treatment is used to achieve a significant reduction of the pollution load.

The use of the biological filter allows a high level of treatment, without resorting to any type of electromechanical equipment.


Should be installed in areas where there is no waste water drainage system.• Ideal for installation in soil that is difficult to excavate or where groundwater levels are high.

• Recommended for use in:


• Provides high-quality final treated effluent that seeps into the ground through sink wells or seepage trenches.

27

COMPACT SEPTiC TANK

Septic Tank with Pre-Filter and Biological FilterRef.

Volume(L)

Inhab.Eq.

Diameter(mm)

Height(mm)

Tubes(mm)

Length(mm)

Lid(mm)

FCC1500

FCC5000

FCC25000

FCC45000

FCC65000FCC70000

FCC75000

FCC2500

FCC20000

FCC40000

FCC60000

FCC8000

FCC30000

FCC50000

FCC15000

FCC35000

FCC55000

1500 6

5000 15

25000 70

45000 155

65000 235

70000 260

75000 275

2500 10

20000 55

40000 140

60000 210

8000 25

30000 90

50000 170

15000 45

35000 115

55000 185

940

1520

2320

2320

2320

2320

2320

1350

2320

2320

2320

1840

2320

2320

2320

2320

2320

1020 DN110

1565 DN110

2460 DN160

2460 DN160

2460 DN160

2460 DN160

2460 DN160

2200

2916

6640

11760

17880

18160

19440

1405 DN110

2460 DN160

2460 DN160

2460 DN160

1890 DN110

2460 DN160

2460 DN160

2460 DN160

2460 DN160

2460 DN160

2250

5360

10480

15600

3315

7920

13040

4580

9200

13320

2x ø400

2x ø400

2x ø600

2x ø600

2x ø600

2x ø600

2x ø600

2x ø400

2x ø600

2x ø600

2x ø600

2x ø400

2x ø600

2x ø600

2x ø600

2x ø600

2x ø600

28

ANTi-ODOUR CARTRiDGE

Principle:Premier Tech’s Anti-odour Cartridge intercepts the odours naturally generated by waste water treatment systems.

Premier Tech’s Anti-odour Cartridge uses an innovative activated fibre technology. These fibres allow the passage of air while intercepting offensive odour and are 10 times quicker than activated carbon technology.

Installation:• • Easy, quick installation.

- The Anti-odour cartridge should be inserted in the DN110 ventilation duct, at a height that allows easy replacement. The installation is made using a DN100 PVC female adapter, which should be fastened to the inside of the ventilation duct.

- It should be placed at the end of the ventilation duct, right below the static ventilator.

- The cartridge should be placed as close as possible to the fumes emission point, taking into consideration its adaptation to the installation’s layout.

Durability:One to three years, depending on use.

29

Principle:Because of their radical, highly concentrated biological formulas, composed of enzymes and non-pathogenic bacteria, “ACTIFLO” activators are more effective than exclusive bacterial products. The enzyme concentration in these products is decisive to their effectiveness.

BiOLOGiCAL ACTiVATORSACTiFLO

Advantages:• Strong odour reduction.• It optimizes septic tank and tubing operation (preventing clogging and increasing liquefaction).

Presentation:• ACTIFLO - 350g

• Package containing 14 bags, suited for three months and a half of maintenance.

• A bag per week, for a 3m3 septic tank.

Advantages:• Initiating or reactivating equipments.• It radically eliminates odour.• Maintenance of grease separators up to 500 L.• Unclogging Tubing, Septic Tanks and Grease

Separators.

Presentation:• ACTIFLO POWER -500g

• Bulk powder package with dispenser.

• A single package for two shock treatments:

Example: 1 Septic Tank + 1 Grease Separator or 2 Septic Tanks

ACTIFLOMaintenance of septic tanks

ACTIFLO POWER Unclogging/Initiating the digestion process in septic tanks and grease separators

30

DEPÓSITOS HORIZONTAIS DE SUPERFICIEDepoitos Horizontais PEAD

31

Technology Capsule SolidoCleansing technology with a 3 year warranty

SilentSOLIDO SMART operates in complete silence thanks to its hermetically sealed capsule.

Value-orientedSOLIDO SMART operates very economically and efficiently. Save money on your electricity bill - the device has an annual/per capita consumption of just approximately 49 kWh.

A considerably lower consumption when compared to most compact waste water treatment plants.

The ControllerA single tube for protecting the cable connecting the control device to the system

• Ready for connection and easy to handle

• Allows for indoor and outdoor assembly (weather protection)

32

Solido SMARTMicro domestic waste water treatment station

Description and characteristics:SOLIDO SMART micro waste water treatment plants were developed by Premier Tech for the efficient, cost-effective treatment of effluents generated by single-family housing and small population centres.

SOLIDO SMART units are sold ready to be installed and stand out for their simple set up, reduced consumption, easy operation, low maintenance and excellent treatment performance.

(1) Reservoir(2) Technology Capsule Solido(3) Air-lift(4) Tubular diffuser(5) Sample collection box with discharge tube(6) Aspiration (manhole, sewer entrance,

biological sludge removal)(7) Aeration(8) Control device

1

62

75

3

4

Complete SBR (6-25HE) Systems

33

Average results in accordance with the requirements of standard EN 12566-3Effluent

CQO

NH4-N

CBO5

SST

N total

P total

Outlet

(mg/l) 39,0

(mg/l) 0,7

(mg/l) 4,9

(mg/l) 12,1

(mg/l) 10,8

(mg/l) 2.5

% Removal

95,4

98,0

98,6

97,2

83,3

65,8

SólidoSMART

SólidoSMART DUO

Ref.Flow rate (m3/day)

HE

KSTA3000 6

KSTA5200 12

KSTA5000DUO 10

KSTA5000 10

KSTA3000DUO 6

KSTA7600 18

KSTA9900 25

Volume(L)

0,9

1,8

1,5

1,5

0,9

2,7

3,75

Lenght (mm)

Height(mm)

Diam.(mm)

1480 18002420

2050 23702740

1860 24702470

3000

6000

5000

1860 21802470

1480 21402420

2050 23703420

2320 27803300

5000

3000

8000

10000

InstalledPower

(w)

TubesI/O

(mm)

39 DN110

58 DN110

58 DN110

58 DN110

38 DN110

125 DN110

210 DN110

* SMART DUO model, with controller integrated into the blower, inside the capsule.

34

ECOFLO® - COMPACT COCONUT FiLTER

Description and characteristics:Ecoflo® Compact Coconut Filter solutions are designed for effective treatment of domestic waste water with individual sanitation. After pre-treatment in the septic tank, the waste water is treated through the Premier Tech Compact Coconut Filter.

Ready-to-install, Ecoflo® solutions are compact, environmentally-friendly (made of organic, vegetable and reusable filter), low-maintenance and durable. They consume no energy, adapt easily to all types of outdoor areas and require no treatment adjustments.

Offering high-performance, the filtering medium using “coconut shell fragments” is the corner stone of our technology (European Patent assigned to 19-09-2003, number EP 1539325B1).

1 - Tank with Premier Tech Pre-filter2 - Premier Tech Compact Coconut filter3 - Filtering medium (coconut shell fragment) 4 - Treated effluent outlet

Equipment approved in accordance with standard EN 12566-3 - EC Marking

35

Cutting-edge individual sanitation technology:The patented filtration element, made of coconut shell fragments, was developed by the Premier Tech technical and scientific team. For the past 20 years, our researchers have been developing the best filtering elements for waste water treatment.

Following several long-term laboratory and field tests, coconut shell fragments were chosen for their high purification capacity and durability.

Ecoflo® Compact Coconut Filters use a patented effluent feed and ventilation process in which calibrated coconut shell fragments act as small sponges with high absorption capacity (5 times greater than sand) and a large biologically active specific contact surface area.

This ecological filling allows the bacteria to nest, ensuring a high level of purification in a small volume and under all conditions of use.

Parameters

SST (mg/l)

CBO5 (mg/l)

Treated effluent (Output)

13(1) (96,4%)

10(1) (97%)

11(2) (97%)

Decree-Law 152/97

35

25

Average Results of (*) Premier Tech Compact Coconut filter

(*) Tests on effluents with concentrations of 361(1) mg/l SST, 310(1) and 343(2) mg/l CBO5(1) Average of 26 samples taken in accordance with the requirements of standard EN 12566-3(2) Average of 16 samples taken from more concentrated effluents in accordance with the requirements of standard EN 12566-3

36

ECOFLO® - COMPACT COCONUT FiLTER

Septic Tank with PF17 Pre-filter COMPACT COCONUT FiLTER

5/6 IE

10/12 IE

15/18 IE

Advantages:• Easy installation, Compact (8m2 per 5 HE).

• Low sludge production (tank is cleaned every 3-4 years and the filter every 10 years, depending on use).

• Outlet at bottom or top (with pump).

• No equipment subject to failure.

• Supports load variations (suitable for main or secondary homes).

• Odour-free treatment.

• No energy required for treatment.

• No treatment adjustments required.

• Natural, renewable and recyclable filter element.

• Complies with Standard EN 12566-3

Ref.Comp.(mm)

Height(mm)

Lid (ø)(mm)

Tub. (ø)(mm)

Lenght.(mm)

5

6

10

12

15

18

5

6

10

12

15

18

Ref.Vol.(L)

IE IE

FHC2000

FHC2000

FHC3000

FHC5000

FHC5000

FHC5000

1

1

2

2

3

3

2000

2000

3000

5000

5000

5000

ECOFLO5HE

ECOFLO6HE

ECOFLO5HE

ECOFLO6HE

ECOFLO5HE

ECOFLO6HE

Length (mm)

1725

1725

2375

2210

2210

2210

2750

3450

2750

3450

2750

3450

Height(mm)

Lid (ø)(mm)

Diam.(mm)

1630

1630

1630

1865

1865

1865

1410

1400

1410

1400

1410

1400

400

400

400

400

400

400

1510

1510

1510

1840

1840

1840

1210

1200

2920

2900

4630

4600

Tub. (ø)(mm)

110

110

110

110

110

110

1140x740

1140x740

1140x740

1140x740

1140x740

1140x740

110

110

110

110

110

110

Qt.

2 to 3 channel distributors

MARKED

EUROPEAN STANDARD

EN 12566-3

38

Ecoprocess™ Solutions from 25 to 1000HE

Compact Coconut Filter Fixed Bed Sequential Batch Reactor

de 21 a 200 HE de 51 a 300 HE de 150 a 1000 HE

waste water treatment solutions for companies and small population centres

39

High-performing, reliable and cost-efficient solutions tailored to meet your budget

Ecoprocess™ Sequential Batch Reactor Solutions were developed for effective treatment of domestic waste water for sanitation in villages of 150 to 1000 inhabitants equiv. These solutions are based on an activated sludge treatment process that treats waste water using a sequence of hydraulic controls operated by a pre-pro-grammed electricity panel.

Ecoprocess™ Compact Coconut Filter Solutions (with fibre or HDPE tanks) are designed for effecti-ve treatment of domestic waste water in small conurbations from 21 to 200 inhabitants equivalent. Following pre-treatment in the septic tank, effluents undergo treatment through a Premier Tech Compact Coconut Filter

• Ecoprocess™ Compact Coconut Filter Solutions

• Ecoprocess™ Fixed Bed Solutions

• Ecoprocess™ Sequential Batch Reactor Solutions

Ecoprocess™ Fixed Bed Solutions provide effective treatment of domestic waste water for sanitation in conurbations of 51 to 300 inhabitants equiv. This Biological treatment system is known as “Aerated Fixed Bed”

40

ECOPROCESS™Compact coconut filter

Ecoprocess™ Compact Coconut Filter Solutions are designed for effective treatment of domestic waste water in small conurbations from 25 to 180 inhabitants equivalent.

After pre-treatment in the septic tank, the effluent is treated through a Premier Tech Compact Coconut Filter.

CHARACTERISTICS OF UNTREATED WASTE WATEREquipment dimensioned according to the following characteristics:

• 60 g CBO5/Inhab. eq.-day, 135 g CQO/Inhab. eq.-day, 70 g SST/Inhab. eq.-day• 150 l/Inhab. eq.-day

TREATED EFFLUENT RESULTS 1, 2

CB05 10 mg/l (97%)CQO 85 mg/l (88%)SST 13 mg/l (96%)

1 - Tests on untreated effluents at concentrations of 361mg/l TSS, 310 mg/l CBO5 and 706 mg/l CQO; EN 12566-3

2 - Average of 26 samples taken in accordance with the requirements of Standard

41

MARKED

EUROPEAN STANDARD

EN 12566-3

42

ECOPROCESS™Compact coconut filter - Capacity: 25 to 45 HE

1 - Septic tank with integrated pre-filter 2- Reservoir with Premier Tech Compact Coconut Filter 3- Filtering medium (coconut shell fragment)4 - Treated effluent outlet (with sample collection box as recommended option)

DimensionamentoPopulation

Septic tankQuant./Cap.

External feeddistributor

Compact coconut filter Quant./Cap.

no

no

no

1 Unit / 12 m3

1 Unit / 15 m3

1 Unit / 20 m3

25 Inhabitants

35 Inhabitants

45 Inhabitants

1 Unit / 25 HE

1 Unit / 35 HE

1 Unit / 45 HE

43

TECHNiCAL CHARACTERiSTiCSMILLENIUM Septic tanks with pre-filter proposed by Premier Tech (dimensions in m)

Compact coconut filter (dimensions in m)

*measuring from the lower part of the tank to the highest level of the manhole, lid not mounted ;**water trickle measured from the lower part of the reservoir.hypothetical, non-binding levels, which can vary around +/- 5% (a measurement on site will allow the installer to confirm the actual levels).

Volume

Population

(A)Length

(A)Length

(B)Diam.

(B)Diam.

(C)Height*

(C)Height*

(D)Inlet**water level


(E)Outlet** water level


Lids 1

Lids 1

Lids 2

Lids 2

Weight(kg)

Weight(kg)

Diam.Inl./Outl.

(mm)

Diam.Inl./Outl.

(mm)

12 m3

25 HE

ø 0,15

2x1,14x0,74

425

1 660

4,78

6,70

2,05 2,14 1,87 1,75

15 m3

35 HE

não

3x1,14x0,74

530

2 400

4,58

9,70

20 m3

45 HE

ø 0,60

4x1,14x0,74

720

3 100

5,36

12,70

2,32

2,25

2,46

1,74

2,08

1,40

2,03

0,03

160

110 0,85x0,65

ø 0,60

MARKED

EUROPEAN STANDARD

EN 12566-3

44


1- Septic tank with integrated pre-filter 2- External feed distributor with rotating flow control 3 - Reservoir(s) with Premier Tech Compact Coconut Filter 4 - Filtering medium (coconut shell fragment) 5 - Treated effluent outlet (with sample collection box as recommended option

Dimensioning

1 Unit / 2 Chennels

1 Unit / 2 Chennels

1 Unit / 2 Chennels

1 Unit / 25 m3

1 Unit / 30 m3

1 Unit / 40 m3

50 Inhabitants

70 Inhabitants

90 Inhabitants

2 Units / 25 HE

2 Units / 35 HE

2 Units / 45 HE

PopulationSeptic tankQuant./Cap.

External feeddistributor

Compact coconut filter Quant./Cap.

45


External feed distributor with rotating flow control (dimensions in m)



Nº Channels

Population

Length

(F)Length

width

(G)Width

Height*

(H)Height*

Inlet**water level

(J)Inlet**water level

Outlet** water level

(K) Outlet** water level

Lid 1

Lids 1 Lids 2

Weight (kg)

Weight (kg)

DiameterInl./Outl. (mm)

DiameterInl./Outl.

(mm)

25 m3

2-3V

25 HE 2x1,14x0,74

840

10

1 660

6,64

0,66

6,70

30 m3

35 HE 3x1,14x0,74

960

2 400

7,92

9,70

40 m3

45 HE 4x1,14x0,74

1262

3 100

10,48

12,70

2,32

0,56

2,25

2,46

0,53

1,74

2,08

0,27

1,40

2,03

0,03

0,03

160

110

110 0,85x0,65

ø 0,60

ø 0,40(oblong)

ø 0,60

MARKED

EUROPEAN STANDARD

EN 12566-3

Volume(A)

Length(B)

Diam.(C)

Height*



Lids 1 Lids 2Weight

(kg)

Diam.Inl./Outl.

(mm)

46


1- Septic tank with integrated pre-filter 2- External feed distributor with rotating flow control 3- Reservoir(s) with Premier Tech Compact Coconut Filter 4- Filtering medium (coconut shell fragment) 5- Treated effluent outlet (with sample collection box as recommended option

DimensioningPopulation

Septic tankQuant./Cap.

External feed distributorCompact coconut filter

Quant./Cap.

1 Unit / channels

1 Unit / channels

2 Unit / 50 m3 + 15 m3

2 Unit / 50 m3 + 30 m3

140 HE

180 HE

4 Unit / 35 HE

4 Unit / 45 HE

47


External feed distributor with rotating flow control (dimensions in m)



Nº Channel Length width Height*(D) Inlet**

water level(E) Outlet** water level

Lid 1Weight

(kg)Diameter

Inl./Outl. (mm)

15 m3

4

35 HE 2x1,14x0,74

530não

10

1 660

4,58

0,66

6,70

30 m3

45 HE 4x1,14x0,74

960

3 100

7,92

12,70

50 m3 1 60013,04

2,32

0,56

2,25

2,46

0,53

1,74

2,08

0,27

1,40

2,03

0,03

0,03

160

110

110 0,85x0,65

ø 0,60

ø0,40(oblonga)

ø 0,60

MARKED

EUROPEAN STANDARD

EN 12566-3

Volume(A)

Length(B)

Diam.(C)

Height*



Lids 1 Lids 2Weight

(kg)

Diam.Inl./Out.

(mm)

Population (F)Length

(G)Diam.

(H)Height*

(J) Inlet**water level

(K) Outlet** water level

Lids 1 Lids 2Weight

(kg)

DiameterIn/Out (mm)

48

wwTP

Description and characteristics:Compact WWTPs, also known as Mini WWTPs are secondary treatment devices used for the treatment of domestic waste water. Using a combination of extended aeration followed by secondary sedimentation, they achieve water discharge environmental values that comply with the DL. 236/98.

An SBR-type WWTP consists of a single inner space where the cycles of aeration, sludge settling and discharge occur sequentially and cyclically. All these types of WWTPs are equipped with an aeration system, which supplies oxygen to the micro-organisms and also promotes homogenization of the mixed liquor. An electric pump is installed inside the tank to discharge the treated effluent. An electric pump is installed inside the tank to discharge the treated effluent.

All electromechanical components are controlled by a single Electrical Control Panel.


Should be installed in areas where there is no waste water drainage system.Recommended for use in:


49

SBR Type waste water Treatment StationEquipped with a biological reactor, air supply diffusers, discharge pump and electrical control panel.

Note: The equivalent inhabitants value is merely informative. The correct sizing of the equipment requires an assessment of the headage and number of inhabitants foreseen for the project.

Ref.

SBR100

SBR250

SBR75

SBR200

SBR125

SBR50

SBR150

Volume(L)

Inhab.Eq.

30000 100

65000 250

20000 75

55000 200

35000 125

15000 50

40000 150

Diameter(mm)

2320

2320

2320

2320

2320

2320

2320

Height(mm)

Lid(mm)

Lenght(mm)

2460 ø600

2460 ø600

6640

17880

2460 ø600

2460 ø600

2460 ø600

2460 ø600

2460 ø600

5360

14320

9200

4580

10480

Tubes(mm)

Power(kw)

ø200 2,15

ø200 4,15

ø200 2,15

ø200 4,15

ø200 2,15

ø200 1,36

ø200 2,35

50

wwTP

Description and characteristics:Compact WWTPs, also known as Mini WWTPs are secondary treatment devices used for the treatment of domestic waste water. Using a combination of extended aeration followed by secondary sedimentation, they achieve water discharge environmental values that comply with the DL. 236/98.

A continuous WWTP consists of a biological reactor equipped with an aeration system that supplies oxygen to the microorganisms and promotes the homogenization of the mixed liquor. This reactor is followed by a settling tank responsible for sedimentation of the biological sludge. The settling tank is equipped with an electric sludge recycling pump to keep the load of micro-organisms in the reactor constant.

All electromechanical components are controlled by a single Electrical Control Panel.


Should be installed in areas where there is no waste water drainage system.Recommended for use in:


52

wwTP

53

Continuous waste water Treatment StationEquipped with a biological reactor, settler, aeration system with submersible injectors

Note: The equivalent inhabitants values are merely informative. The correct sizing of the equipment requires an assessment of the headage and number of inhabitants foreseen for the project.

Ref.Volume

(L)Inhab.

Eq.Diameter

(mm)Heigth(mm)

Lid(mm)

Tube(mm)

Power(Kw)

Length(mm)

ETAR100

ETAR250

ETAR75

ETAR200

ETAR125

ETAR50

ETAR150

30000 100

60000 250

25000 75

55000 200

35000 125

15000 50

40000 150

2320 7920 2460 2x600

2320 15600 2460 2x600

2320 6640 2460 2x600

2320 14320 2460 2x600

2320 9200 2460 2x600

2320 4580 2460 2x600

2320 10480 2460 2x600

ø200 2,15

ø200 3,95

ø200 2,15

ø200 3,95

ø200 2,15

ø200 1,36

ø200 2,15

54

Sample collection box

Description and characteristics:Sample collection box quick and easy to install, made of rotomoulded High-Density Polyethylene.

Totally sealed, with a low weight, it offers high mechanical resistance and is highly resistant to chemicals as well as corrosion-proof.

Ref.

CXAMOS

Volume (L)

-

Width (mm)

360

Height (mm)Length (mm)

810-

55

Screening box

Description and characteristics:The dredging box consists of a primary treatment element which retains all larger solids present in the raw waste water to prevent solids from entering the other treatment elements, including grease separators, septic tanks and WWTPs.

Equipped with a grid of galvanized steel bars installed at a 45 ° angle with 25 mm spacing between them. Also equipped with a basket for discharge of seeped materials.


Cleaning of the equipment is facilitated by two lids which open fully and lock.

Ref.

CXGRAD

Volume (L)

-

Width (mm)

565


5701575

HYDROCARBON SEPARATORSClass 1

Description and characteristics:Hydrocarbons are pollutant compounds that are part of the constitution of mineral oils. They include petrol, diesel and fuel or used oils.

The Hydrocarbon separator is a device used for the physical treatment of oily water contaminated with hydrocarbons through which the oils found in oily waste water are separated. This process makes it possible to achieve discharge values in accordance with the requirements in the existing legislation, the Decree Law 236/98 of 1 August.

The Hydrocarbons Class I Separator is prefabricated in High-Density Polyethylene (HDPE) and designed according to European Standard EN-858 for all oily waters.

The equipment consists of the following main elements:

- Settling Area - Coalescing Area - Coalescing Filter - Shutt-off valve

MARKED

EUROPEAN STANDARD

EN 858

56

57

Treatment Flow 1,5 and 100 l/sClass I separators with coalescing filter to obturator valve.

Ref.Flow rate(L/seg.)

Volume(L)

Width(mm)

Height(mm)

TLid(mm)

Length(mm)

Tube(mm)

Other sizes and models available upon request.

IH001

IH003

1,5 900

3 1400

750

750

1100 Full rectangular

opening

1580

11002350

DN125

DN125

IH006

IH015

IH 050

IH010

IH040

IH100

IH020

IH065

IH030

IH080

6 3200

15 8000

50 25000

10 5000

40 20000

100 45000

20 9000

65 30000

30 15000

80 40000

1350

1840

2320

1520

2320

2320

1840

2320

2320

2320

1720 2x ø400

2210 2x ø400

2640 2x ø600

2500

3400

6640

1890 2x ø400

2640 2x ø600

2640 2x ø600

2210 2x ø400

2640 2x ø600

2640 2x ø600

2640 2x ø600

3300

5360

11760

3800

7920

4100

10480

DN125

DN200

DN315

DN160

DN315

DN315

DN200

DN315

DN315

DN315

Large Flow Compact Hydrocarbon SeparatorsTreatment Flow 40 to 200 L/s. Class I separators with coalescing filter to obturator valve.

Ref.

IHGC040

IHGC050

Flow rate(L/sec.)

Volume(L)

40 10000

50 10000

Width(mm)

2320

2320

Height(mm)

Lid(mm)

Length(mm)

26403300

26403300

Tube(mm)

DN315

DN315

IHGC065

IHGC100

IHGC080

IHGC150

IHGC200

65 15000

100 25000

80 20000

150 35000

200 45000

2320

2320

2320

2320

2320

2640 2x ø600

2x ø600

2x ø600

2640 2x ø600

4580

6640

2640 2x ø600

2640 2x ø600

2640 2x ø600

5360

9200

11760

DN315

DN315

DN315

DN400

DN500

Other sizes and models available upon request.

MARKED

EUROPEAN STANDARD

EN 1825-1

58

GREASE SEPARATORS

Description and characteristics:Grease, animal and vegetable oils are pollutants found in cooking oils such as frying oil, margarines and butters.

The grease separator is a device used for the physical treatment of oily water contaminated with fats. It separates the oils found in oily waste water and provides discharge values in accordance with the requirements in existing legislation under Decree Law 236/98 of 1 August. aims to reduce the concentration of oils and grease in the discharge to below 15 mg/l.

The oily water contaminated with fats comes from several sources, including canteens, restaurants, butcher shops, slaughter houses, and catering establishments.

Prefabricated in HDPE, the Grease Separator is designed in accordance with Standard EN-1825-1 to receive all the oily water produced in the installation but is not set up to receive concentrated waste oil. It is also not allowed to route waste water to the Grease Separator.

59

Ref.Flow rate(L/sec.)

Volume(L)

Width(mm)

Height(mm)

Lid(mm)

Length(mm)

Tube(mm)


Volume(L)

Width(mm)

Height(mm)

Lid(mm)

Length(mm)

Tube(mm)

Point-source Grease Separator

SG100 0,5 100 420 420 Rectangular Full opening

580 DN50

SG200 0,75 200 560 7101050 DN110

Above Ground Simple Grease Separator

SGA500

SGA2000

SGA1000

SGA3000

SGA5000

1 500

4 2000

2 1000

6 3000

10 5000

730

1350

940

1520

1840

750 ø220

1360 ø400

1250

1665

950 ø400

1565 ø400

1865 ø400

1450

1945

2210

DN90

DN110

DN110

DN160

DN200

SGA300 0,75 300 580 650 ø2701320 DN90

60

SEPARADORES DE GORDURAS

Underground Grease Separator with Settler

SG002

SG007

SG004

SG012

SG020

2 1000

7 2800

4 1900

12 5000

20 8000

940

1350

940

1520

1840

1305 2x ø400

1600 2x ø400

1600

2250

1305 2x ø400

1820 2x ø400

2140 2x ø400

2300

2920

3320

DN110

DN160

DN110

DN200

DN200

Underground Grease Separator

SGE500SGE300

SGE2000

SGE15000

SGE1000

SGE10000

SGE3000

SGE5000

10,75

500300

4 2000

30 15000

2 1000

20 10000

6 3000

10 5000

730580

1510

2320

940

2320

1510

1860

750650

ø220ø270

1630 ø400

2460 ø600

12501320

1725

4580

950 ø400

2460 ø600

1630 ø400

1890 ø400

1450

3300

2375

2470

DN90DN90

DN110

DN200

DN110

DN200

DN160

DN200


Volume(L)

Width(mm)

Height(mm)

Lid(mm)

Length(mm)

Tube(mm)


Volume(L)

Width(mm)

Height(mm)

Lid(mm)

Length(mm)

Tube(mm)

61

MARKED

EUROPEAN STANDARD

EN 1825-1

62

PUMPiNG STATiONS

Description and characteristics:The prefabricated Pumping Stations presents as an ideal solution when pumping drainage water, rainwater or sewage is needed to overcome differences in flow level between manifolds, i.e., whenever a gravity flow is not possible.

Our Pumping Stations area ready-to-install solutions, made from polyethylene, rot-proof, and provided with locking lids.

They can be supplied single, double or triple, equipped with one or two vortex type pumps, with their electrical control panel, valves and level switches.

The electric pumps are equipped with a guidance system for the automatic descent and docking bases for coupling.

63

Depósitos duplos para estações de bombagem.

Ref.

DEED390

DEED520

Volume (L)

2 x 390

2 x 520

Diameter (mm)

580

580

Length (mm)

-

-

Height (mm) Lid (mm)

1500 2 x ø 400

2000 2 x ø 400

PUMPiNG STATiONSDouble tanks for pumping stations.

Ref.

DEES260

DEES520

DEES390

Volume (L)

260

520

390

Diameter (mm)

580

580

580

Length (mm)

-

-

-


1000 ø 400

2000 ø 400

1500 ø 400

64

PUMPiNG STATiONSBox

Description and characteristics:The prefabricated Pumping Stations are an ideal solution when pumping drainage water, rainwater or sewage is needed to overcome differences in flow level between manifolds, i.e., whenever a gravity flow is not possible.

Our Pumping Stations area ready-to-install solutions, made from polyethylene, rot-proof and provided with locking lids.

They are manufactured in High-Density Polyethylene (HDPE), presenting as main features: low weight; high chemical resistance; high mechanics; and corrosion-proof.

This product line has two types of tanks:

- SINGLE BOX For installation of one submersible electric pump

- DOUBLE BOX For installation of two submersible electric pumps

Both equipments are available for supply either without any other equipment or fully operational, equipped with one or two vortex type pumps, level switches and an electrical control panel.

The flow rates and monometric heights are the maximum operating values of each electric pump. For each application, we recommend consulting the respective pump’s performance curve.

65

DOUBLE BOX430L Container (lid, add-on and tank) Ready for installation of a submersible electric pump.

Ref.

BOXD

Volume (L)

430

Width (mm)

1120

Length (mm)

750


1130 2 x ø 400

SiNGLE BOX214L Container (lid, add-on and tank) Ready for installation of a submersible electric pump.

Pumping stations without equipment

Ref.

BOXS

Volume (L)

214

Width (mm)

550

Length (mm)

750


1130 ø 400

66

PUMPiNG STATiONSBox

SiNGLE-PHASE SiNGLE BOX214L Container (lid, add-on and tank)1X electric pump with vortex type impeller, compression piping

THREE-PHASE SiNGLE BOX214L Container (lid, add-on and tank) 1 X electric pump with vortex type impeller, 1 X level switch, 1 x electrical protection and control panel, compression piping.

Equipped pumping stations

Ref.

BOXS7VX

BOXS7VXT

BOXS10VX

BOXS10VXT

BOXS15VX

BOXS15VXT

BOXS20VXT

Vol.(L)

214

214

214

214

214

214

214

Width(mm)

550

550

550

550

550

550

550

Length.(mm)

FlowRote Max.

L. Min

750

750

750

750

750

750

750

260

260

400

400

450

450

550

Heigth(mm)

Height Manometrics

mcaLid

(mm)

Ref.Vol.(L)

Width(mm)

Length.(mm)

FlowRote Max.

L. MinHeigth(mm)

Height Manometrics

mcaLid

(mm)Power

kW

PowerkW

1130

1130

1130

1130

1130

1130

1130

9,1

9,1

7,7

7,7

9,1

9,1

11

ø 400

ø 400

ø 400

ø 400

ø 400

ø 400

ø 400

0,55

0,55

0,7

0,7

1,1

1,1

1,5

67

Ref.Vol.(L)

Width(mm)

Length.(mm)

FlowRote Max.

L. MinHeigth(mm)

Height Manometrics

mcaLid

(mm)Power

kW

Ref.Vol.(L)

Width(mm)

Length.(mm)

FlowRote Max.

L. MinHeigth(mm)

Height Manometrics

mcaLid

(mm)Power

kW

SiNGLE-PHASE DOUBLE BOX430L Container (lid, add-on and tank)2 X electric pump with vortex type impeller, compression piping.

THREE-PHASE DOUBLE BOX430L Container (lid, add-on and tank) 2 X electric pump with vortex type impeller, 4 X level switch, 1 x electrical protection and control panel, compression piping.

Equipped pumping stations

BOXD7VX

BOXD7VXT

BOXD10VX

BOXD10VXT

BOXD15VX

BOXD15VXT

BOXD20VXT

430

430

430

430

430

430

430

550

550

550

550

550

550

550

750

750

750

750

750

750

750

520

520

800

800

900

900

1100

1130

1130

1130

1130

1130

1130

1130

9,1

9,1

7,7

7,7

9,1

9,1

11

2 x ø 400

2 x ø 400

2 x ø 400

2 x ø 400

2 x ø 400

2 x ø 400

2 x ø 400

2 x 0,55

2 x 0,55

2 x 0,7

2 x 0,7

2 x 1,1

2 x 1,1

2 x 1,5

68

Modular pumping stationsin reinforced polyester.Internal equipment:Standard or «customized»

Applications:• Drainage water

• Sewage water

• Rainwater

• Water recirculation

• Industrial applications

With over 20 years experience, Premier Tech shares its know-how in the conceptionand production of pumping stations with automatically controlled electric pumps.

68

PUMPiNG STATiONS Electroflo

69

High quality reservoirs Cylindrical, made from reinforced polyester, with high mechanical resistance, durability, and reliability, designed specifically for pumping water.

A professional teamWith a vast experience in creating and assembling pumping stations.

A production unit devoted to the manufacture and assembly of pumping.

Flexibility, responsiveness, and manufacturing quality. Possibility of customization to meet our clients’ demands.dos clientes.

High quality electric pumps and equipments.

Selectivity, competitiveness and good performance of the proposed material.

Perfect adaptation to your needs.Reservoirs available in several heights and diameters, large offer of equipment and fittings.

ELECTROFLO

ø Reservoir

1258

1638

Standard heights for production

de 2 a 6m

de 2 a 6m

DN63 DN90 DN110 DN160

Max. flow rates(m3/h)DN200

Number of electric pumps:(installation bases, piping, valves)

1 a 3 1 a 2 - - 120 m3h-

1 a 4 1 a 3 1 a 3 1 a 2 360 m3h-(*para alturas superiores consultar-nos; ** Consultar-nos)

70

ECOiLUsed Oils Storage Tanks

Description and characteristics:Double wall tank specially designed and engineered to store used oil in optimal safety and hygiene conditions.

Made of High-Density Polyethylene, the tanks have a double wall, level indicator, leak display and drainage rack for filters and other contaminated equipment.

Fully sealed and with a low weight, they are

highly resistant to chemicals, corrosion-proof and offer high mechanical resistance.

ECOiL 300,600 and 1200Equipped with double walls, level indicator, drainage rack and leak viewer.

Ref.

ECOIL300

ECOIL1200

ECOIL600

Volume (L)

300

1200

600

Diameter (mm)

800

1400

1030

Height (mm)Length. (mm)

1140

1510

-

-

1340-

Lid (mm)

440 x 310

440 x 310

440 x 310

71

CAiXAS DE BATERiAS

Description and characteristics:The Battery Case is used for correct storage and transportation of batteries and current accumulators.

Built from High-Density Polyethylene (HDPE), these cases are watertight and highly resistant to chemicals meeting the requirements Decree-Law No. 62/2001, Article 5, Decree 572/2001, Annex II, Paragraph g, Ministry of Economy and Environment.

Completely sealed and low in weight, they offer high mechanical resistance, are highly resistant to chemicals and corrosion-proof.

They have a base for transportation and handling by forklift.

Ref.

CXBAT250

CXBAT500

Volume (L)

250

500

Width (mm)

635

735

Length (mm) Lid (mm)Length (mm)

695 Full opening960

865 Full opening1010

72

2500 SELECTiVE COLLECTiON CONTAiNERHDPE Container

Description and characteristics:Selective collection containers with a 2500 L capacity. The rectangular shape allows Selective collection containers with a 2500 L capacity. The rectangular shape allows the placement of several juxtaposed containers, thus creating aesthetically integrated and harmonious eco points.

The absence of any structures in the middle of the container maximizes its use and means that the container can be filled uniformly.

The 2500 model containers are made of rotomoulded High-Density Polyethylene (HDPE) with UV protection. Can be manufactured in several colours by the addition of colouring pigments.

Galvanized steel reinforcement and dumping device designed so that the stress borne by the polyethylene housing surrounding the counter is almost zero. The reinforcement, the discharge trapdoors, the opening arms, the chassis and the clamping system all made of high-quality galvanized steel.

The container is emptied by opening the base through a single piece discharge trapdoor which opens fully. This characteristic allows the discharge trapdoor to be opened automatically so there is contact and slight pressure from the foot switch. Following discharge, the container simply needs contact with the ground to lock again.

73

2500 SELECTiVE COLLECTiON CONTAiNERRef.

CRS2500AS (Simple ring opening)

CRS2500AD (Double ring opening )

Volume (L)

2500

2500

Width (mm)

1300

1300

Heigth (mm)Length (mm)

18001200

18001200

74

BOXLiNE

Description and characteristics:Selective collection containers with a 1000 L capacity. Rectangular shape allows the placement of several juxtaposed containers, thus creating aesthetically integrated and harmonious eco points.

The absence of any structures in the middle of the container maximizes its use and means that the container can be filled uniformly.

BOXLINE containers are made of rotomoulded High-Density Polyethylene (HDPE) and have with UV protection. Can be manufactured in several colours by the addition of colouring pigments.

This container is available in two versions:• With door-opening

• Designed for the use of 120, 240 and 360 L capacity Two-Wheel containers (MGB). Equipped with a front and/or back door and a lock to reserve access to authorized operators only.

• Discharge trapdoor.

The discharge trapdoor is positioned at the bottom of the container and opens automatically when there contact and a light pressure on the foot switch on the collection vehicle’s tailgate. Following discharge, the container simply needs contact with the ground to lock again.

The lifting system consists of a single ring positioned at the top of the container. The reinforcement, the discharge trapdoors, the opening arms, the chassis and the clamping system all made of high-quality galvanized steel.

75

BOXLiNE 1000Ref.

BOX1000AS (Simple ring )

BOX1000PT (Door opening)

Volume (L)

1000

1000

Width (mm)

860

860


1350970

1350970

(*) Option:

For collection of used cooking oil, the lid is equipped with a mechanism to prevent the removal of empties from the top.

(*)

76

SUPER FUSTO

Description and characteristics:Vertical cylindrical container manufactured in rotomoulded High-Density Polyethylene.

It comes in two models:

• Selective Collection: Container fitted with a lid for easy access for the the selective collection of miscellaneous waste including packaging, cardboard, bottles, filters, paper-containing waste, brake pads, etc.

• Safety: Secure shipping and storage container with standard 200 L metal or plastic drums. Equipped with flat lid with galvanized steel fastening strap to guaranty proper locking and sealing of the container.


Ref.

SUPFCUR(Selective collection)

SUPFLIS(Safety)

Volume (L)

300

300

Diameter (mm)

630

630


1330

1330

-

-

Lid (mm)

440 x 310

Full opening

77

DRUM SUPPORT

Ref.

CRADLE

Width (mm)

875


545720

Description and characteristics:Support for 200 L drums.

Manufactured in High-Density Polyethylene (HDPE), these containers are totally sealed and low in weight, they offer high mechanical resistance and are corrosion-proof.

78

RETENTiON BASiNS

Description and characteristics:Constructed of High-Density Polyethylene (HDPE), these basins are used for reception and storage of oil and chemicals and to prevent spillage. Can be equipped with galvanized steel or pultruded grate.

Fully sealed, offer high mechanical resistance, are highly resistant to chemicals, and corrosion-proof.

The storage of chemicals complies with precise safety rules in order to protect operators and the environment in case of spillages (leaks). To reach this objective, all chemicals should be stored in a retention system.

All storage of fluids presenting a contamination risk to water and soil must be associated to a retention volume, which must be at least equal to the greater of the following two values:

• 100% of the capacity of the tank with the largest volume.

• 50% of the result of the sum of the different volumes.

BR1200GA 1360 1325 9301325

Ref.

BR100GA

BR400GA

BR200GA

BR600GA

Volume (L)

70

415

245

640

Width (mm)

670

670

670

1175


140

555

1265

1240

330

480

1240

1280

80

MiNiBOOTHwC BOOTH and SHOwER BOOTH

Free-standing sanitary booths.

Ideal for construction sites, public works, areas of difficult access or areas with or without a sewer network

Caraterísticas Comuns:• Made of rotomoulded High-Density Polyethylene

(HDPE)

• Features adapted for passage through doors

• Wheels and handles are ideal for manual handling

• Height adjustment rings integrated into the body of the cabin

• Lock with key

WC characteristics:• Toilet paper holder

• Polyethylene or ceramic toilet with sewer connection

• Chemical WC

• Injection mould toilet cover

Shower characteristics:• Cold water shower

• Soap dish

• Shower base with sewer network

• Hanger on the door

81

Ref.

SIMPLES MINIBOOTHNo hand basin)

CONFORT MINIBOOTH(With hand basin)

LOUÇA MINIBOOTH(Porcelain toilet with network connection)

SHOWER MINIBOOTH(network connection)

Width (mm)

775

775

775

775


1900

1900

1900

1900

970

970

970

970

Minibooth Description

Ref.

Simples

Louça

Shower

Conforto

Mobile English-style toilet bowl

70 L

X

-

-

X

Sanitary ceramic

-

X

-

-

Wheels

X

X

X

X

rings Reservoir

X

X

X

X

Wash-basin

-

-

-

X

Handle for

traction

X

X

X

X

Cleanwater

Door withlock and

Key

- X

-

-

X

X

X

Lid

X

X

-

X

Toilet paper holder

X

X

-

X

Shower Faucet

-

-

X

-

Soap dish

-

-

X

-

Hanger

-

-

X

- X

82

MECAPLAST AND MECABi

Mecaplast and Mecabi are free-standing sanitary booths.

Ideal for construction sites, public works, areas of difficult access or areas with or without a sewer network.

Characteristic:• Injection mould toilet cover

• Height adjustment rings

• Toilet paper holder

• Lock with key

• Easy to clean

• Chemical-based WC or with connection to a sewer network

• English or Turkish style WC

• Ideal for construction sites, civil construction sites, public works, areas of difficult access or areas with or without a sewer network

Ref.

MECAPLAST(Chemical and Connection to sewer network)

MECABI(Chemical and Connection to sewer network)

Width (mm)

1200

1200

Heigth (mm) Weight (Kg)Length (mm)

2400 130

2300 115

1200

1200

83

Mecaplast and Mecabi description

English-style WC, 200 L, water injector0102030405060708091011121314

X

-

X

X

X

X

X

X

X

X

X

X

-

X

X

-

X

X

X

X

X

X

X

X

X

X

X

X

-

X

X

X

X

X

X

-

X

X

X

X

-

X

-

X

X

X

X

X

X

-

X

X

X

X

-

X

CHARACTERISTICSMecabi Mecaplast

chemical chemicalConnection to

sewer networkConnection to

sewer network

Turkish-style WC with water injector

Interior lock with vacant/occupied indicator

Door with interior mirror and coat hanger

Wall pass-through and 2’’ valve for sewer connection

Thermoformed door and ceiling

Ventilation grille

Urinal

Water reservoir and lavatory

Foot pump for flushing

Toilet paper holder

Four height adjustment rings

Spring-equipped door for smooth closing

Male/Female identifier

84

FUEL TANK iBCVolumes: 200 and 410 L

Description and characteristics:IBC mobile tank, made of high density polyethylene, UV-resistant, with capacities of 200L and 410L, produced according to European standard ADR.

Suitable for the safe storage and distribution of “C” class fuels (with a boiling point above 55°C, such as diesel) on agricultural, industrial or other machinery, without risk of contamination or spillage.

Made by rotomolding, they are highly resistant, easy to handle and can be transported in open or closed vans or trucks, thus allowing the refuelling of the machines on site/where they are working, eliminating trips to the supply station.

Ref.

DGADR200

DGADR410

Volume (L)

200

410

Width (mm)

760

760


5401160

8201160

- Vibration- Lifting (from bottom)- Lifting (from top)- Stacking- Water tightness (20 kPa)- Hydraulic pressure (120 kPa)- Impact (fall of full tank from 80 cm from the ground)

APPROVEDIN ADR TRIALS

85

Characteristics:Pump 12V - maximal flow rate 50 l/minSupply hose with 4 meters and automatic dispenser2” Filling NozzleFuel level gauge inside tankHigh Precision Digital Litre Measuring Device +/- 0.5% (Optional) 6Shut off valve and fishing tube with mesh filterAdjustable locks with possibility of padlock placementHeight adjustment rings integrated into the bodyAllows stackingHandling cavities for pallet jack or forkliftCavity for fastening strapLid stoppersSide and front manual handles for manual handling

6

7

8

9

10

11

12

13

7

78

89

11

11

12

13

13

13

5

4

3

2

1

6

5

4 3

2

1

86

ADBLUE Tank - iBCVolumes: 200 and 410 L

Description and characteristics:IBC mobile tank, made of high density polyethylene, UV-resistant, with capacities of 200L and 410L, produced according to European standard ADR.

Suitable for the safe storage and distribution of ADBLUE on agricultural, industrial or other machinery, without risk of contamination or spillage.

Made by rotomoulding, they are highly resistant, easy to handle and can be transported in open or closed vans or trucks, thus allowing the refuelling of the machines on site/where they are working, eliminating trips to the supply station.

Ref.

GRG200ADBLUE

GRG200ADBLUE

Volume (L)

200

410

Width (mm)

760

760


5401160

8201160

Durante 90 anos, a Premier Tech tem vindo a construir o seu Know-how e reputação na experiência e sinergia dos seus três grupos: horticultura e Agricultura, Equipamentos Industriais e Tecnologias Ambientais. A sua missão é tornar-se líder tecnológico e comercial nas suas respectivas áreas. Com uma equipa multidisciplinar de mais de 3.000 pessoas na América, Europa e Ásia, a Premier Tech concentra-se no desenvolvimento dos seus colaboradores, na inovação e no lançamento de produtos e serviços de valor agregado para assegurar o seu crescimento a longo prazo.

Nº 11616

catalogue - premier techpremiertech.pt/pdf/catalogo(premier_tech)uk.pdf · description and...

Documents