catalog: swan secure fasteners (c-sstswan09) · c-sstswan09 ©2009 simpson strong-tie company inc....

SWAN SECUREFASTENERSC-SSTSWAN09

Distributed by: BEST MATERIALS LLC Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014 www.BestMaterials.com Email: [email protected]

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.

Simpson Strong-Tie ® Swan Secure Fasteners

4

TABLE OF CONTENTS

Hand-Drive Nails Box, Ring-Shank Nails ......................................................................................................... 56Cedar and Redwood Decking Nails ...................................................................................... 14Fiber-Cement Siding Portland™ Nails ................................................................................. 34Finishing Nails ...................................................................................................................... 65Gutter Spikes ........................................................................................................................ 48Marine Sea-Cure™ Nails ...................................................................................................... 84Post and Beam, Ring Shank Nails ....................................................................................... 56Preservative-Treated Lumber Nails ...................................................................................... 14Roofi ng / Slating, Aluminum Nails ...................................................................................... 45Roofi ng / Slating, Copper Nails ........................................................................................... 44Roofi ng / Slating, Stainless-Steel Nails .............................................................................. 45Roofi ng Nails, Washered ...................................................................................................... 46Shake and Shingle Nails ................................................................................................. 32, 46Siding Nails, Painted ............................................................................................................ 33Siding Nails, Pyramid Head ................................................................................................. 34Structural Connector, Smooth-Shank Nails ........................................................................ 57Tile/Slate Nails, Copper ........................................................................................................ 47Tile/Slate Nails, Stainless Steel ........................................................................................... 48Un-Common™ Common Ring Shank and Smooth Shank Nails .................................. 55, 77Wood Siding Nails ................................................................................................................ 32 Collated Nails Bostitch® – Type Angle Finishing Nails ................................................................................ 66Inserted Plastic-Coil 15° Nails ............................................................................................. 37Paper Tape 31°, Structural Connector, Ring Shank Nails ................................................... 60Paper Tape 31-34°, Clipped Head, Ring-Shank Nails ................................................... 17, 61Paper Tape 31-34°, Full-Round Head, Ring-Shank Nails .................................................... 17Paslode® – Type Angle Finishing Nails ................................................................................. 66Paslode® – Type Straight Finishing Nails ............................................................................. 67Plastic Coil 15° Nails ............................................................................................................ 36Plastic Strip 20-22°, Casing Head, Ring-Shank Nails .................................................. 16, 59Plastic Strip 20-22°, Full Round Head, Ring-Shank Nails ........................................... 15, 57Plastic Strip 20-22°, Full Round Head, Screw-Shank Nails ......................................... 16, 58Plastic Strip 20-22°, Full Round Head, Smooth-Shank Nails ............................................. 59Plastic Strip 31-34°, Full Round Head, Ring-Shank Nails ............................................ 17, 61Senco® – Type Angle Finishing Nails .................................................................................... 66Straight Brads ...................................................................................................................... 67Wire Coil 15°, Roofi ng Nails ................................................................................................. 49Wire Coil 15°, Painted Nails ........................................................................................... 36, 68Wire Coil 15°, Ring-Shank Nails .............................................................................. 18, 35, 60Wire Coil, Ring Shank, Fiber-Cement-Siding Nails ............................................................. 35Wire Weld 28°, Clipped Head, Ring-Shank Nails .......................................................... 18, 59

Hand-Drive Screws Bugle Head, 6-Lobe-Drive Swaneze™ Screws ................................................................... 21Bugle Head, Square-Drive Swaneze™ Screws ................................................................... 20Bugle Head, Square-Drive Swaneze™ Boardwalk™ Screws .............................................. 21 Composite-Decking Composi-Lok™ Screws, Coated, Square Drive ................................. 26Composite-Decking Dexxter™ Screws, 6-Lobe Drive .................................................. 22, 74Composite-Decking Dexxter™ Screws, Painted Trim Head, 6-Lobe Drive ........................ 27Fiber-Cement FY-CEM™ Screws for Wood ......................................................................... 37Flat Head, 6-Lobe-Drive Woodpeckers™ Screws ............................................................... 23

NAILS

SCREWS

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.Simpson Strong-Tie ® Swan Secure Fasteners

5

TABLE OF CONTENTS

MISCELLANEOUS FASTENERS

SCREWS(cont.)

SPECIALTY ITEMS

Gutter Screws ....................................................................................................................... 53Hex-Washer-Head Strong-Drive® Screw ............................................................................. 63Hex-Washer-Head Timber Tamers™ Screws ...................................................................... 62K-Lath Modifi ed Truss Head, Self-Drilling Screws ....................................................... 40, 82K-Lath Modifi ed Truss Head, Wood Screws ....................................................................... 40Marine Sharx™ Screws .................................................................................................. 74, 75Painted Bugle Head, Square-Drive Swaneze™ Screws ....................................................... 25Painted Trim Head, 6-Lobe-Drive Swaneze™ Screws ......................................................... 24Painted Trim Head, 6-Lobe-Drive Woodpeckers™ Screws ................................................. 27Painted Trim Head, Square-Drive Swaneze™ Screws ................................................... 24, 70Pancake/Clip Self-Drilling Screws ....................................................................................... 53Pancake/Clip Type A-Point Screws ..................................................................................... 53Self Drilling, Bugle-Head Billy Goats™ Screws ................................................................... 79Self Drilling, Flat-Head Billy Goats™ Screws with Wings .................................................. 80Self Drilling, FY-CEM™ Fiber-Cement Billy Goats™ Screws for Metal-Studs .............. 38, 82Self Drilling, Marutex Hex-Washer-Head Billy Goats™ Screws .......................................... 81Self Drilling, Trim-Head Billy Goats™ Screws for Metal Studs ..................................... 38, 79Self Drilling, Wafer-Head Billy Goats™ Screws with Wings ............................................... 80Trim-Head, 6-Lobe-Drive Swaneze™ Screws ...................................................................... 19Trim-Head, 6-Lobe-Drive Woodpeckers™ Screws ....................................................... 23, 69Trim-Head, Coated, Square-Drive Screws ........................................................................... 25Trim Head, Square-Drive Swaneze™ Screws .......................................................... 19, 69, 76Trim-Head Swaneze™ Screws, Sealing Washer ................................................................ 77Truss Head, Coarse Thread, Square-Drive Screws ............................................................. 76Truss Head, Self-Drilling Roofi ng Screws ........................................................................... 52Twin-Lead Threads, Hex-Washer-Head Screws (with and without washer) ................ 39, 52

Collated Staples Similar to Bostitch® “BCS” Series Staples .............................................................. 42, 51, 71Similar to Paslode® “GS” Series Staples ................................................................ 41, 51, 71Similar to Paslode® “GSI” Series Staples ........................................................................... 42Similar to Senco® “C” Series Staples .................................................................................. 72Similar to Senco® “L” Series Staples ............................................................................ 50, 71Similar to Senco® “N” Series Staples ....................................................................... 41, 50, 72Similar to Senco® “P” Series Staples ............................................................................ 51, 72

EB-TY® Hidden Deck Fastening Systems ............................................................................ 28Drill ‘n Drive™ Tool ............................................................................................................... 86Fencing Nails ........................................................................................................................ 85Fencing Staples .................................................................................................................... 85Flooring Cleats, “L” Series ................................................................................................... 30Flooring Cleats, “T” Series ................................................................................................... 30Flooring Staples, Similar to Bostitch® ................................................................................. 30Hog Rings ............................................................................................................................. 85Marine Sea-Cure™ Nails ...................................................................................................... 84Premium Driver Bits ............................................................................................................. 86Storm-Panel Screw .............................................................................................................. 87Wood Plugs (Ipê) ................................................................................................................. 87

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


13

DECKING

DECKINGHand-Drive NailsCedar and Redwood ........................................................... 14Preservative-Treated Lumber ............................................. 14

Collated NailsPlastic Strip 20–22°, Stainless, Full Round, Ring Shank .... 15Plastic Strip 20–22°, Bronze, Full Round, Ring Shank ........ 15 Plastic Strip 20–22°, Stainless, Full Round, Screw Shank .. 16Plastic Strip 20–22°, Stainless, Casing Head, Ring Shank .. 16Plastic Strip 31–34°, Stainless, Full Round, Ring Shank .....17Paper Tape, 31–34°, Stainless, Clipped Head, Ring Shank ..17Wire Coil 15°, Stainless, Ring Shank ................................. 18Wire Weld 28°, Stainless, Ring Shank ............................... 18

Hand-Drive ScrewsTrim Head, Square Drive Swaneze™ ................................... 19Trim Head, 6-Lobe Drive Swaneze™ ................................... 19Bugle Head, Square Drive Swaneze™ ................................. 20Bugle Head Swaneze™ Boardwalks™ .................................. 21Bugle Head, 6-Lobe Drive Swaneze™ ................................. 21Composite Decking, 6-Lobe Drive Dexxter™ ..................... 22Flat Head, 6-Lobe Drive Woodpeckers™ ............................ 23Trim Head, 6-Lobe Drive Woodpeckers™ ........................... 23

Hand-Drive Screws, Painted-HeadTrim Head, Square Drive Swaneze™ ................................... 24Trim Head, 6-Lobe Drive Swaneze™ ................................... 24Bugle Head, Square Drive Swaneze™ ................................. 25Standard Coated Trim Head, Square Drive ........................ 25Composite Decking, Square Drive Composi-Lok™ ............. 26Trim Head, 6-Lobe Drive Woodpecker™ ............................. 27Composite Decking, Trim Head, 6-Lobe Drive Dexxter™ ..... 27

EB-TY® Hidden Deck Fastening SystemAll Styles ............................................................................ 28

Flooring Cleats and Staples“T” Shape Cleats ................................................................. 30“L” Shape Cleats .................................................................. 30Flooring Staples (similar to Bostitch®) .............................. 30

Photo courtesy of California Redwood Association


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


14

DECKING Hand-Drive Nails

PennySize Length Gauge Shank

DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket

Item No.Available

in 3162

8d1 2 1⁄2" 12 .109" 7⁄32" 145 S8CRD25 S8CRD5 S8CRD1 S8CRDB

10d 3" 12 .109" 7⁄32" 120 S10CRD25 S10CRD5 S10CRD1 S10CRDB

12d 3 1⁄4" 12 .109" 7⁄32" 110 S12CRD25 S12CRD5 S12CRD1 S12CRDB

16d 3 1⁄2" 11 .120" 1⁄4" 88 S16CRD25 S16CRD5 S16CRD1 S16CRDB

• Annular ring threads provide secure attachment of cedar, redwood and other stable decking materials to deck joists and reduce nail head popping.

• Slender shanks permit nailing at board ends with reduced splitting.• Small unobtrusive checker pattern heads blend with wood grain and diffract sunlight.• Decking nails available pre-fi nished in tan, redwood and gray colors –

contact Simpson Strong-Tie for price and availability.• Choose type 316 for seaside applications and superior corrosion resistance• Bucket = 25 lbs.

HAND-DRIVE NAILS | Cedar and Redwood


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket

Item No.Availablein 316*

8d 2 1⁄2" 11 .120" 9 ⁄32" 115 S8PTD25 S8PTD5 S8PTD1 S8PTDB

8d 2 1⁄2" 10 .134" 9 ⁄32" 94 S8HPTD25 S8HPTD5 S8HPTD1 S8HPTDB

10d 3" 10 .134" 9 ⁄32" 79 S10PTD25 S10PTD5 S10PTD1 S10PTDB

10d 3" 9 .148" 5 ⁄16" 67 S10HPTD25 S10HPTD5 S10HPTD1 S10HPTDB



16d 3 1⁄2" 8 .165" 11⁄32" 44 S16HPTD25 S16HPTD5 S16HPTD1 S16HPTDB

20d 4" 8 .165" 11⁄32" 40 S20PTD25 S20PTD5 S20PTD1 S20PTDB

20d 4" 6 .203" 7⁄16" 25 S20HPTD25 S20HPTD5 S20HPTD1 S20HPTDB

• Annular ring threads provide greater pull-out resistance, reduce nail-head popping• Checkered fl at head, diamond point• Larger shank diameter easily penetrates both green and seasoned preservative-treated pine• Ideal for decks and docks• Choose type 316 for seaside applications and superior corrosion resistance

HAND-DRIVE NAILS | Preservative-Treated Wood / ACQ

304 and 316 Stainless Steel


1. When ordering 8d nails in colors, insert the fi rst letter of the color after the 5th character in the model number. EXAMPLE: S8CRD5 becomes S8CRDT5 when ordering Tan. Contact Simpson Strong-Tie for details on other sizes.2. For sizes available in 316 stainless steel ( ), substitute the letter “T” as the fi rst character of the item number.

* For sizes available in 316 stainless steel ( ), substitute the letter “T” as the fi rst character of the item number.

All of our hand-driven nails can be ordered passivated for a nominal up-charge. Passivation is a light acid bath that cleans the fastener of surface contaminants and aids in preventing premature corrosion.

!

Tan Redwood Gray

Available in 3 colors

See note below

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


15

DECKING Collated Nails

• 20–22° collation angle • 9⁄32" diameter checker-patterned round head• Orange or clear glue on nails to further increase pull-out resistance• Choose type 316 for seaside applications and superior corrosion resistance• Silicon bronze offers resistance to stress corrosion cracking under nail heads

COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Ring Shank

Silicon Bronze

Length ShankDiameter

BoxCount Item No.

2 1⁄2" .120" 4000 I11A250CNB

2 1⁄2" .120" 1000 I11A250CNJ

3 1⁄4" .120" 4000 I11A325CNB

3 1⁄4" .120" 1000 I11A325CNJ

Compatible Pneumatic Tools – Collated 20–22° Plastic Stripsee following page >


BoxCount Item No. Available

in 316*

2" .113" 5000 S12A200CNB

2" .113" 1000 S12A200CNJ

2" .120" 5000 S11A200CNB

2" .120" 1000 S11A200CNJ

2 1⁄4" .148" 1000 S9A225CNJ —

2 3⁄8" .113" 5000 S12A237CNB

2 3⁄8" .113" 1000 S12A237CNJ

2 1⁄2" .120" 4000 S11A250CNB

2 1⁄2" .120" 1000 S11A250CNJ

2 1⁄2" .134" 4000 S10A250CNB —

3" .120" 4000 S11A300CNB

3" .120" 1000 S11A300CNJ

3" .134" 4000 S10A300CNB

3" .134" 1000 S10A300CNJ

3 1⁄4" .120" 4000 S11A325CNB

3 1⁄4" .120" 1000 S11A325CNJ

3 1⁄4" .134" 4000 S10A325CNB

3 1⁄4" .134" 1000 S10A325CNJ

3 1⁄2" .134" 4000 S10A350CNB

3 1⁄2" .134" 1000 S10A350CNJ



C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


16




in 316*

2" .113" 5000 S12S200CNB

2" .113" 1000 S12S200CNJ

2 1⁄2" .113" 4000 S12S250CNB

2 1⁄2" .113" 1000 S12S250CNJ

3" .120" 4000 S11S300CNB

3" .120" 1000 S11S300CNJ

3 1⁄4" .120" 4000 S11S325CNB

3 1⁄4" .120" 1000 S11S325CNJ

3 1⁄2" .134" 4000 S10S350CNB

3 1⁄2" .134" 1000 S10S350CNJ

• 20–22° collation angle • 9⁄32" diameter smooth round head• Orange or clear glue on nails to further increase pull-out resistance• Choose type 316 for seaside applications and superior corrosion resistance

Compatible Pneumatic Tools – Collated 20–22° Plastic Strip

Bostitch® RN90, RN95HN (up to .162"), N88RH (up to .162"), N88RH-2MCN, F21PLDewalt® D51845, D51844Duo-Fast® CN350, SNP-83, NSP-350FFasco® R5C-RHN20-90SSHitachi® NR83A (up to 3 1⁄4"), NR90AC2 (up to .162"), NR90AC, NR90AA2, NR83AG, NR90SSCMakita® AN8300, AN922MAX® SN890RH, SN90, GS683Paslode® 5350/SRH20Porter Cable® FR350, FR350A, FR350MAGSenco® FramePro 600FRH & FramePro 602 (up to 3 1⁄2"), FramePro 650FRH (2 1⁄4" to 3 1⁄2"),

FramePro 652 (up to 3 1⁄2"), FramePro 700XL FRH, FramePro 702XP (upto 3 1⁄2") & FramePro 752XP (up to 3 1⁄2"), SN60, SN65C (up to .162")

Stan-Tech® SDN11, SDN11B-1

• 20–22° collation angle• 1⁄4" diameter checker-patterned, countersunk casing head • Orange or clear glue on nails to enhance pull-out resistance• Available with painted heads – see below

COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Screw Shank

COLLATED NAILS | Plastic Strip 20–22°, Casing Head, Ring Shank



304 Stainless Steel


BoxCount Item No.

2 3⁄8" .120" 1000 S11A237KDJ

3 1⁄4" .134" 1000 S10A325KDJ

1. When ordering in colors, substitute the last three letters in the model number: KJB = Brown, KJG = Gray, KJR = Redwood, KJS = Sienna; KJT = Tan. Example: a 2 3⁄8" nail in Brown is model S11A237KJB.


Brown Gray Redwood Sienna Tan

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


17


COLLATED NAILS | Paper Tape 31–34°, Clipped Head, Ring Shank



in 316*

2" .113" 1000 S12A200T31

2 3⁄8" .113" 1000 S12A237T31

3" .120" 1000 S11A300T31

3 1⁄4" .131" 1000 S10A325T31

3 1⁄2" .131" 1000 S10A350T31

• 31–34° collation angle• Choose type 316 for seaside applications and superior corrosion resistance

• 31–34° collation angle • 9⁄32" diameter checker-patterned round head• Choose type 316 for seaside applications and superior corrosion resistance




in 316*

2 3⁄8" .113" 4000 S12A237B31

2 3⁄8" .113" 1000 S12A237P31

3" .120" 4000 S11A300B31

3" .120" 1000 S11A300P31

3 1⁄4" .131" 4000 S10A325B31

3 1⁄4" .131" 1000 S10A325P31


Compatible Pneumatic Tools – Collated 31–34° Plastic Strip and Paper Tape

Bostitch® F33PT, N90PT (2"–3 1⁄2")DeWalt® D51823, D51822Duofast® NSPM-325F & CN-325BHitachi® NR83AA & NR83AA2, NR90AAMakita® AN942MAX® SN890CH/34, GS683CHPaslode® F350S Powermaster Plus, Impulse 325 & 350, 5325S, 5300 Plus & 5350S,

F250S-PP, IMCT (2" to 3 1⁄4")Porter Cable® FC350, FC350ASenco® SN4, SN70, FramePro 600 & FramePro 650, SN325+, FramePro 601 (up to 3 1⁄2")

& FramePro 701XP (up to 3 1⁄2"), FramePro 651 (up to 3 1⁄2"), FramePro 750XL (up to 3 1⁄2") & FramePro 751XP (up to 3 1⁄2")

Spotnails® YTD90




C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


18


PennySize Length Shank

DiameterHeadSize


in 316*

4d 1 1⁄2" .099" 1⁄4" 3600 S12A150PNB —

5d 1 3⁄4" .099" 1⁄4" 3600 S12A175PNB —

6d 2" .099" 1⁄4" 3600 S12A200PNB —

7d 2 1⁄4" .099" 1⁄4" 1800 T12A225PNJ **

8d 2 1⁄2" .099" 1⁄4" 3600 S12A250PNB

8d 2 3⁄8" .113" 1⁄4" 3600 S12A237PNB —

10d 3" .120" 17⁄64" 1800 S11A300PNJ

10d 3" .131" 17⁄64" 1800 S10A300PNJ

12d 3 1⁄4" .120" 17⁄64" 1800 S11A325PNJ

12d 3 1⁄4" .131" 17⁄64" 1800 S10A325PNJ

16d 3 1⁄2" .131" 17⁄64" 1800 T10A350PNJ **


• 15° collation angle; stainless-steel collation medium• Choose type 316 for seaside applications and superior corrosion resistance

* For sizes available in 316 stainless steel ( ), substitute the letter “T” as the fi rst character of the item number.** Item available in 316 stainless steel only.

Compatible Pneumatic Tools – Collated 15° Wire Coil

Bostitch® Bostitch N80CB, N86C & N100C, N100CPP, N130C-2Fasco® F5C CN15W75 (up to 3") & CN15W90 (up to 3 1⁄4")Hitachi® NV65AB & NV65AC (up to 2 1⁄2"), NV83A (up to 3 1⁄4"), NV75AG (.099" to .131", 1 3⁄4" to 3")Makita® AN621 (1 3⁄4"–2 1⁄2"), AN901 (1 3⁄4"–3 1⁄2")MAX® CN80, CN70 (1 3⁄4" to 2 3⁄4"), HN75, HN90, 80F, CN100 (2 1⁄2" to 4"), CN565S (1 3⁄4" to 2 1⁄2"), CN890II,

CN565 (1 1⁄2" to 2 1⁄2"), CN890S, CN665 (1 1⁄2" to 2 1⁄2"), CN565D (1 3⁄4" to 2 1⁄2"), CN565S (1 3⁄4" to 2 1⁄2")Paslode® F325C, P350C (1 1⁄2" to 3 1⁄4"), F275C, P275C (1 1⁄2" to 2 3⁄4"), 4275/CN70 (2" to 2 1⁄2"),

5325/CN80 & 5350C, 5300C (up to 3")Porter Cable® Coil 350 (up to 3 1⁄2") , Coil 250 (up to 2 1⁄2")Senco® SCN56 (up to 2 1⁄2"), SCN60 (2" to 2 1⁄2"), SCN65 (2" to 3 1⁄2") & SCN300 (1 3⁄4" to 3")Spotnails® MCW64 (up to 2 1⁄2"), YCN83 (up to 3 1⁄4")

• 28° collation angle • Clipped head, welded wire collation


BoxCount Item No.

2 3⁄8" .113" 1000 S12A237W28

3" .120" 1000 S11A300W28

3 1⁄4" .131" 1000 S10A325W28

COLLATED NAILS | Wire Weld 28°, Clipped Head, Ring Shank

COLLATED NAILS | Wire Coil 15°, Ring Shank

Compatible Pneumatic Tools – Collated 28° Wire Weld

Bostitch® N16, N80SB,N86S (2" to 3 1⁄2"), N88WW, N100S, N70S & N70SB (2" to 3"), N100S (2" to 4")Craftsman® 18430Max® SN890CH/28Porter Cable® FM350A

304 Stainless Steel

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


19

DECKING Hand-Drive Screws

Size Length Approx.Count per lb.

BucketCount

5 lb.Item No.

1 lb. Item No.

Bucket Item No.

Deck PackItem No.

70-PackItem No.

Availablein 316*

#7 1" 316 5000 S07100FB5 S07100FB1 S07100FBB S07C100PAK — —

#7 1 1⁄4" 256 5000 S07125FB5 S07125FB1 S07125FBB S07C125PAK — —

#7 15⁄8" 195 1750 S07162FB5 S07162FB1 S07162FBBKT** S07162BFBP** S07162BFBR70**

#7 2" 154 4000 S07200FB5 S07200FB1 S07200FBB S07C200PAK — —

#7 2 1⁄4" 138 1750 S07225FB5 S07225FB1 S07225FBBKT** S07225BFBP** S07225BFBR70**


#7 3" 98 1750 S07300FB5 S07300FB1 S07300FBBKT** S07300BFBP** S07300BFBR70**


#9 4" 61 1000 S09400FB5 S09400FB1 S09400FBB — — —

* For sizes available in 316 stainless steel ( ), substitute the letter “T” as the fi rst character of the item number.** Includes #1 square-drive bit.

HAND-DRIVE SCREWS | Swaneze™ Trim Head, Square Drive


Size Length 6-LobeDrive

Approx.Count per lb.

Carton/BucketCount

Bulk Carton Item No.

Bucket Item No.

Deck PackItem No.

Availablein 316*

#7 15⁄8" T-15 195 4000 S07162FTC S07162FTB SO7C162FTP —

#7 2 1⁄4" T-15 138 3000 S07225FTC S07225FTB S07C225FTP

#7 3" T-15 98 2000 SO7300FTC S07300FTB S07C300FTP —


• 0.230" diameter T-15 6-lobe drive, trim head• Type-17 point for fast starts• 6-lobe drive prevents driver bit cam-out and stripping in recess• Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate• Pre-drilling recommended near board ends to prevent splitting• Use with stable woods and wood substitutes for less noticeable fastening• Slender #7 shank for fi nish work and trim• Deck Pack contains enough screws to fasten 100 square feet

(6" nominal boards on 16" centers)• Choose type 316 for seaside applications and superior corrosion resistance

HAND-DRIVE SCREWS | Swaneze™ Trim Head, 6-Lobe Drive


• Type-17 point for fast starts• Trim head• Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate• Pre-drilling recommended near board ends to prevent splitting• Use with stable woods and wood substitutes for less noticeable fastening• Deck Pack contains enough screws to fasten 100 square feet

(6" nominal boards on 16" centers)• #7 screw has 0.230" head diameter and #1 square drive recess• #9x3 1⁄2" screw has 0.250" head diameter and #1 square drive recess• #9x4" screw has 0.250" head diameter and #2 square drive recess• Choose type 316 for seaside applications and superior corrosion resistance• Screws available in various packaging sizes and types from 1 lb. boxes to deck packs,

bulk cartons and durable buckets

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


20



Carton/BucketCount

5 lb.Item No.

1 lb. Item No.


Bucket Item No.

Deck PackItem No.

Availablein 316*

#6 5⁄8" 408 12,000 S06062DB5 S06062DB1 S06062DBC S06062DBB — —

#6 3⁄4" 352 10,000 S06075DB5 S06075DB1 S06075DBC S06075DBB — —

#6 1" 295 8000 S06100DB5 S06100DB1 S06100DBC S06100DBB — —

#6 1 1⁄4" 243 5000 S06125DB5 S06125DB1 S06125DBC S06125DBB — —

#6 1 5⁄8" 195 4000 S06162DB5 S06162DB1 S06162DBC S06162DBB — —

#8 3⁄4" 285 10,000 S08075DB5 S08075DB1 S08075DBC S08075DBB — —

#8 1 1⁄8" 226 5000 S08112DB5 S08112DB1 S08112DBC S08112DBB — —

#8 1 1⁄4" 185 5000 S08125DB5 S08125DB1 S08125DBC S08125DBB S08C125PAK


#8 2" 128 3000 S08200DB5 S08200DB1 S08200DBC S08200DBB S08C200PAK

#8 2 1⁄4" 109 3000 S08225DB5 S08225DB1 S08225DBC S08225DBB S08C225PAK —


#8 3" 82 1500 S08300DB5 S08300DB1 S08300DBC S08300DBB S08C300PAK —

#10 1" 172 4500 S10100DB5 S10100DB1 S10100DBC S10100DBB — —

#10 1 1⁄4" 153 4000 S10125DB5 S10125DB1 S10125DBC S10125DBB — —

#10 1 1⁄2" 134 3500 S10150DB5 S10150DB1 S10150DBC S10150DBB — —

#10 1 3⁄4" 115 3000 S10175DB5 S10175DB1 S10175DBC S10175DBB — —

#10 2" 96 2500 S10200DB5 S10200DB1 S10200DBC S10200DBB —

#10 2 1⁄4" 88 2000 S10225DB5 S10225DB1 S10225DBC S10225DBB — —


#10 3" 68 1500 S10300DB5 S10300DB1 S10300DBC S10300DBB S10C300PAK


#10 3 3⁄4" 54 1000 S10375DB5 S10375DB1 S10375DBC S10375DBB — —


• 0.344" diameter, #2 square drive bugle head• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate• Pre-drilling recommended near board ends to prevent splitting• Deck Pack contains enough screws to fasten 100 square feet

(6" nominal boards on 16" centers)• Choose type 316 for seaside applications and superior corrosion resistance

HAND-DRIVE SCREWS | Swaneze™ Bugle Head, Square Drive


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


21



Carton/BucketCount


Bucket Item No.

5 lb.Item No.

1 lb. Item No.

Availablein 316*

#12 2 1⁄2" 56 2000 S12250DBC S12250DBB S12250DB5 S12250DB1

#12 3" 48 1500 S12300DBC S12300DBB S12300DB5 S12300DB1

#12 3 1⁄2" 42 1000 S12350DBC S12350DBB S12350DB5 S12350DB1

#12 4" 36 800 S12400DBC S12400DBB S12400DB5 S12400DB1

#12 4 1⁄2" 32 750 S12450DBC S12450DBB S12450DB5 S12450DB1

#12 5" 29 500 S12500DBC S12500DBB S12500DB5 S12500DB1

#12 5 1⁄2" 28 500 S12550DBC S12550DBB S12550DB5 S12550DB1

#12 6" 24 600 S12600DBC S12600DBB S12600DB5 S12600DB1

#14 3" 36 1000 S14300DBC S14300DBB S14300DB5 S14300DB1

#14 3 1⁄2" 33 750 S14350DBC S14350DBB S14350DB5 S14350DB1

#14 4" 26 700 S14400DBC S14400DBB S14400DB5 S14400DB1

#14 5" 21 500 S14500DBC S14500DBB S14500DB5 S14500DB1

#14 6" 18 500 T14600DBC T14600DBB T14600DB5 T14600DB1 **

• 0.430" diameter #3 square drive bugle head• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw the decking

tightly to the substrate• Pre-drilling recommended near board ends to prevent splitting• Choose type 316 for seaside applications and superior corrosion resistance

HAND-DRIVE SCREWS | Swaneze Boardwalk™ Bugle Head, Square Drive



Size Length 6-LobeDrive


Carton/BucketCount


Bucket Item No.

5 lb.Item No.

1 lb. Item No.

Deck PackItem No.

Availablein 316*

#6 1 1⁄4" T-15 243 5000 S06125DTC S06125DTB S06125DT5 S06125DT1 — —

#6 1 5⁄8" T-15 195 4000 S06162DTC S06162DTB S06162DT5 S06162DT1 — —

#8 1 5⁄8" T-20 150 4000 — S08162DTB S08162DT5 S08162DT1 — —

#8 2" T-20 128 3000 S08200DTC S08200DTB S08200DT5 S08200DT1 — —

#10 2 1⁄2" T-25 82 2000 S10250DTC S10250DTB S10250DT5 S10250DT1 S10C250DTP

#10 3" T-25 68 1500 S10300DTC S10300DTB S10300DT5 S10300DT1 S10C300DTP

#10 3 1⁄2" T-25 56 1000 S10350DTC S10350DTB S10350DT5 S10350DTI — —

• 0.344" diameter T-15, T-20 and T-25 6-lobe drives• Type-17 point for fast starts• 6-lobe drive prevents driver bit cam-out and stripping in recess• Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate• Pre-drilling recommended near board ends to prevent splitting• Choose type 316 for seaside applications and superior corrosion resistance

HAND-DRIVE SCREWS | Swaneze™ Bugle Head, 6-Lobe Drive



C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


22


Size Length HeadDiameter

6-LobeDrive

CartonCount

Bulk CartonItem No.

Deck PackCount

Deck PackItem No.

Availablein 316*

#10 1 1⁄2" 0.265" T-20 1750 S10150DXB 350 S10150DXP —

#10 2" 0.265" T-20 1750 S10200DXB 350 S10200DXP —

#10 2 1⁄2" 0.265" T-20 1750 S10250DXB 350 S10250DXP

#10 3" 0.265" T-20 1750 S10300DXB 350 S10300DXP —

• Unique thread form removes exhaust while driving to reduce “mushrooming” in composite decking

• Type-17 point for fast starts• 6-lobe drive prevents driver bit cam-out and stripping in recess• Small head diameter is less visible• Painted heads available, see page 27• 6-lobe driver bit included in both Contractor Packs and Deck Packs• Choose type 316 for seaside applications and superior corrosion resistance• Patent pending

HAND-DRIVE SCREWS | Dexxter™ Composite Decking, 6-Lobe Drive



Deck Packs contain enough screws to fasten 100 sq. ft. (6" nominal boards on 16" centers).Contractor Packs contain enough screws to fasten 500 sq. ft. (6" nominal boards on 16" centers).

!All square drive and 6-lobe-drive screws are best driven using our specialty driver bits. Our bits are manufactured in the U.S.A. to our exacting standards – resulting in far fewer stripped recesses, longer bit life, less waste, and greater effi ciency (see page 86).

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


23


• Penetrate the hardest wood products with ease• Unique 4-corner thread form with raised-ridge technology greatly reduces driving torque• 6-lobe drive prevents driver bit cam-out and stripping in recess• Self-countersinking nibs under the head ensure fl ush installation• Choose type 316 stainless steel for superior corrosion resistance• Threaded approximately 2⁄3 up the shank to tightly draw the decking to the joist• Pre-drilling recommended near board ends to prevent splitting• 6-lobe driver bit included in both Contractor Packs and Deck Packs

HAND-DRIVE SCREWS | Woodpeckers™ Flat Head, 6-Lobe Drive


6-LobeDrive

CartonCount


Deck PackCount

Deck PackItem No.

#8 1 5⁄8" 0.340" T-20 4000 T08162WPB 350 T08162WPP

#8 2" 0.340" T-20 3000 T08200WPB 350 T08200WPP

#10 2 1⁄2" 0.370" T-25 1750 T10250WPB 350 T10250WPP

#10 3" 0.370" T-25 1750 T10300WPB 350 T10300WPP

#10 3 1⁄2" 0.370" T-25 1000 T10350WPB 250 T10350WPP

#12 4" 0.440" T-27 750 T12400WPB 100 T12400WPP

316 Stainless Steel

• Penetrate the hardest wood products with ease• Unique 4-corner thread form with raised-ridge technology greatly reduces driving torque• 0.230" diameter casing-style head and slender #7 diameter for fi nish work and trim• 6-lobe drive prevents driver bit cam-out and stripping in recess• Pre-drilling recommended near board ends to prevent splitting• Threaded approximately 2⁄3 up the shank to tightly draw the decking to the substrate• Choose type 316 stainless steel for superior corrosion resistance• 6-lobe driver bit included in both Contractor Packs and Deck Packs


6-LobeDrive

CartonCount


Deck PackCount

Deck PackItem No.

70-PackItem No.

Availablein 316

#7 1 5⁄8" 0.230" T-15 1750 T07162WPBKT 350 T07162WPP T07162WPR70 **#7 2 1⁄4" 0.230" T-15 1750 T07225WPB 350 T07225WPP T07225WPR70 **#7 3" 0.230" T-15 1750 T07300WPB 350 T07300WPP T07300WPR70 **#8 2 1⁄2" 0.260" T-15 1750 S08250WPB 350 S08250WPP — —


HAND-DRIVE SCREWS | Woodpeckers™ Trim Head, 6-Lobe Drive

** Item available in 316 stainless steel only.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


24

DECKING Hand-Drive Screws with Painted Heads

Size Length Head Color Contractor PackCount

Contractor Pack Item No.

Deck PackCount

Deck PackItem No.

Availablein 316*

#7 1 5⁄8" Gray 1750 T07162FCG 350 T07162FJG **#7 1 5⁄8" Ipê 1750 S07162FCI 350 S07162FJI#7 1 5⁄8" Tan 1750 T07162FCT 350 T07162FJT **#7 1 5⁄8" White 1750 T07162FCW 350 S07162FJW#7 2 1⁄4" Almond 1750 S07225FCA 350 S07225FJA —#7 2 1⁄4" Black 1750 S07225FCBB 350 S07225FJB —#7 2 1⁄4" Gray 1750 S07225FCG 350 S07225FJG#7 2 1⁄4" Ipê 1750 S07225FCI 350 S07225FJI#7 2 1⁄4" Khaki 1750 S07225FBK 350 S07225FJK —#7 2 1⁄4" Tan 1750 S07225FCT 350 S07225FJT#7 2 1⁄4" White 1750 S07225FCW 350 S07225FJW#7 2 1⁄4" Azek Gray 1750 S07225FCZ 350 S07225FZJ —#7 2 1⁄4" Mocha 1750 S07225FCM 350 S07225FJM —#7 3" Gray 1750 S07300FCG 350 S07300FJG —#7 3" Ipê 1750 S07300FCI 350 S07300FJI —#7 3" Tan 1750 S07300FCT 350 S07300FJT —

• Durable, powder-coated fi nish – painted heads blend with decking material• 0.230" diameter #1 square drive, trim head• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate• Slender #7 shank for fi nish work and trim• Pre-drilling recommended near board ends to prevent splitting• Use with stable woods and wood substitutes when screw heads need to be hidden• Choose type 316 for seaside applications

and superior corrosion resistance

HAND-DRIVE SCREWS | Swaneze™ Painted Trim Head, Square Drive

HAND-DRIVE SCREWS | Swaneze™ Painted Trim Head, 6-Lobe Drive



Size Length Head Color 6-LobeDrive

ContractorPack Count


Deck PackCount

Deck Pack Item No.

Availablein 316*

#7 1 5⁄8" White T-15 1750 S07162TCW 350 S07162TJW#7 2 1⁄4" Acorn T-15 1750 S07225TCA 350 S07225TJA#7 2 1⁄4" Black T-15 1750 S07225TCB 350 S07225TJB#7 2 1⁄4" Lt. Gray T-15 1750 S07225TCG 350 S07225TJG#7 2 1⁄4" Pewter T-15 1750 S07225TCE 350 S07225TJE#7 2 1⁄4" Sahara T-15 1750 S07225TCS 350 S07225TJS#8 2 1⁄2" Almond T-15 1750 T08250FCA 350 T08250FJA **#8 2 1⁄2" Gray T-15 1750 S08250TCG 350 S08250TJG —#8 2 1⁄2" Jatoba T-15 1750 S08250TCJ 350 S08250TJJ —#8 2 1⁄2" Khaki T-15 1750 T08250FBK 350 T08250FJK **#8 2 1⁄2" Tan T-15 1750 S08250TCT 350 S08250TJT —#8 2 1⁄2" Mocha T-15 1750 T08250FCM 350 T08250FJM **#8 2 1⁄2" White T-15 1750 T08250FCW 350 T08250FJW **#8 2 1⁄2" Gray T-15 1750 T08250FZC 350 T08250FZJ **



• Durable, powder-coated fi nish – painted heads blend with decking material• Heads colored to match “Trex Escapes®” PVC decking• 0.230" diameter 6-lobe drive trim head• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate• Pre-drilling recommended near board ends to prevent splitting• Slender #7 shank for fi nish work and trim• Use with stable woods and wood substitutes when screw heads need to be hidden

Lt. GrayAcorn Black

Pewter WhiteSahara

Tan Gray Almond Ipê Black White KhakiAzek Gray

Mocha

Almond GrayKhaki

Mocha Tan Jatoba

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


25




Deck PackCount

Deck PackItem No.

#10 2 1⁄2" Ipê 1750 S10250DCI 350 S10250DJI

#10 2 1⁄2" Tan 1750 S10250DCT 350 S10250DJT

#10 3" Gray 1750 S10300DCG 350 S10300DJG

#10 3" Ipê 1750 S10300DCI 350 S10300DJI

#10 3" Tan 1750 S10300DCT 350 S10300DJT

305 Stainless Steel

• Durable, powder-coated fi nish – painted heads blend with decking material• 0.344" diameter #2 square drive bugle head• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw board

tightly to the substrate• Pre-drilling recommended near board ends

to prevent splitting

• Trim head offers a clean, fi nished look• Self-countersinking nibs under the head ensure fl ush installation• Available with a Quik Guard® double-barrier coating and in stainless steel• #2 Undersized square drive• Type-17 tip for fast starts• Pre-drilling recommended near board ends to prevent splitting• Driver bit included in each package

NOTE: Quik Guard® coating has been tested to show less than 10% of surface red rust at 950 hours of ASTM B117 salt spray testing. It is suitable for exterior applications with most preservative-treated woods. It is not suitable for higher exposure environments such as seaside applications, see www.strongtie.com/info for more information.

HAND-DRIVE SCREWS | Swaneze™ Painted Bugle Head, Square Drive

HAND-DRIVE SCREWS | Standard Coated Trim Head, Square Drive

Did you know that we were the fi rst to introduce the stainless-steel, square-driven deck screw to the U.S. market in 1989? Even today our Swaneze™ screws remain an industry standard.

!

GrayIpê Tan

Size Length Color 70-Count BoxItem No.

350-Count BoxItem No.


#8 2 1⁄2" Gray DTHG212R70 DTHG212R350 DTHG212MB

#8 2 1⁄2" Brown DTHB212R70 DTHB212R350 DTHB212MB

#8 2 1⁄2" Red DTHR212R70 DTHR212R350 DTHR212MB

#8 2 1⁄2" Tan DTHT212R70 DTHT212R350 DTHT212MB

#8 2 1⁄2" Stainless Steel DTHSS212R70 DTHSS212R350 —

#8 3" Gray DTHG3R70 DTHG3R350 DTHG3MB

#8 3" Brown DTHB3R70 DTHB3R350 DTHB3MB

#8 3" Red DTHR3R70 DTHR3R350 DTHR3MB

#8 3" Tan DTHT3R70 DTHT3R350 DTHT3MB

#8 3" Stainless Steel DTHSS3R70 DTHSS3R350 —

Quik Guard® Coating and 305 Stainless Steel

RedTanGrayBrown

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


26


• Cutting wings on the shaft counter-bore the deck board, helping to prevent fastener spin out

• Cap-style head reduces mushrooming material, ensuring a cleaner-looking installation

• Available with a Quik Guard® double-barrier coating and in stainless steel • #2 Undersized square drive• Sharp point• Pre-drilling recommended near board ends to prevent splitting• Driver bit included in each package

NOTE: Quik Guard® coating has been tested to show less than 10% of surface red rust at 950 hours of ASTM B117 salt spray testing. It is suitable for exterior applications with most preservative-treated woods. It is not suitable for higher exposure environments such as seaside applications, see www.strongtie.com/info for more information.

HAND-DRIVE SCREWS | Composi-Lok™ Composite, Coated, Square Drive

Size Length Color 70-Count BoxItem No.



#9 2 1⁄2" Gray DCLG212R70 DCLG212R350 DCLG212MB

#9 2 1⁄2" Brown DCLB212R70 DCLB212R350 DCLB212MB

#9 2 1⁄2" Red DCLR212R70 DCLR212R350 DCLR212MB

#9 2 1⁄2" Tan DCLT212R70 DCLT212R350 DCLT212MB

#9 2 1⁄2" Stainless Steel DCLSS212R70 DCLSS212R350 —

#9 3" Gray DCLG3R70 DCLG3R350 DCLG3MB

#9 3" Brown DCLB3R70 DCLB3R350 DCLB3MB

#9 3" Red DCLR3R70 DCLR3R350 DCLR3MB

#9 3" Tan DCLT3R70 DCLT3R350 DCLT3MB

#9 3" Stainless Steel DCLSS3R70 DCLSS3R350 —

Quik Guard® Coating and 305 Stainless Steel

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


27


• Durable, powder-coated fi nish – painted heads blend with decking material• Unique thread form removes exhaust while driving to reduce “mushrooming” in composite decking• Type-17 point for fast starts• 6-lobe drive prevents driver bit cam-out and stripping in recess• Small head diameter is less visible• Pre-drilling recommended near board ends to prevent splitting• 6-lobe driver bit included in both Contractor Packs

and Deck Packs• Patent pending

HAND-DRIVE SCREWS | Dexxter™ Composite Decking , Painted Trim Head, 6-Lobe Drive

Size Length Head Color 6-LobeDrive

Contractor PackCount


Deck PackCount

Deck PackItem No.

#10 1 1⁄2" Brown T-20 1750 S10150XBB 350 S10150XPB#10 1 1⁄2" Gray T-20 1750 S10150XBG 350 S10150XPG#10 1 1⁄2" Ipê T-20 1750 S10150XBI 350 S10150XPI#10 1 1⁄2" Redwood T-20 1750 S10150XBR 350 S10150XPR#10 1 1⁄2" Tan T-20 1750 S10150XBT 350 S10150XPT#10 2 1⁄2" Gray T-20 1750 S10250XBG 350 S10250XPG#10 2 1⁄2" Redwood T-20 1750 S10250XBR 350 S10250XPR#10 2 1⁄2" Tan T-20 1750 S10250XBT 350 S10250XPT#10 2 1⁄2" Ipê T-20 1750 S10250XBI 350 S10250XPI#10 2 1⁄2" Brown T-20 1750 S10250XBB 350 S10250XPB#10 3" Gray T-20 1750 S10300XBG 350 S10300XPG#10 3" Ipê T-20 1750 S10300XBI 350 S10300XPI#10 3" Redwood T-20 1750 S10300XBR 350 S10300XPR#10 3" Tan T-20 1750 S10300XBT 350 S10300XPT

305 Stainless Steel

• Penetrate the hardest wood products with ease• Durable, powder-coated fi nish – painted heads blend with Ipê decking material• Unique 4-corner thread form with raised-ridge technology greatly reduces driving torque• 0.230" diameter casing-style head and slender #7 diameter for fi nish work and trim• 6-lobe drive prevents driver bit cam-out and stripping in recess• Choose type 316 stainless steel for seaside applications and superior corrosion resistance• Pre-drilling recommended near board ends to prevent splitting• Coarse threads approximately 2⁄3 up the shank draw the decking tightly to the substrate• 6-lobe driver bit included in both Contractor Packs and Deck Packs

HAND-DRIVE SCREWS | Woodpeckers™ Painted Trim Head, 6-Lobe Drive


6-LobeDrive

Contractor PackCount

Contractor PackItem No.

Deck PackCount

Deck PackItem No.

Availablein 316

#7 2 1⁄4" 0.230" T-15 1750 T07225WCI 350 T07225WJI **#8 2 1⁄2" 0.260" T-15 1750 S08250WCI 350 S08250WJI —


Deck Packs contain enough screws to fasten 100 sq. ft. (6" nominal boards on 16" centers).Contractor Packs contain enough screws to fasten 500 sq. ft. (6" nominal boards on 16" centers).

!


Tan RedwoodGray IpêBrown

Ipê

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


28

DECKING EB-TY ® Hidden Deck Fastening

The EB-TY provides a unique method of fastening deck boards that makes the fasteners virtually invisible. Fastening is done into the side of the board, leaving a fastener-free deck surface. The EB-TY is a polypropylene biscuit fastener that fi ts into a slot the builder cuts into the edge of the deck boards with a standard biscuit joiner. The EB-TY fasteners are inserted and fastened with a screw driven into the joist. Nesting each successive board against the EB-TY automatically ensures consistent spacing and uniform height.

Easy to install since all fastening is done from the top side• Affords easier deck resurfacing since nail heads are eliminated from • the deck surfaceFormed from UV resistant polypropylene to last the life of the deck• Stainless-steel #7 trim-head screws included• Each EB-TY Deck Pack includes installation instructions and enough EB-TY fasteners, • screws and tapered Ipê wood plugs to install 100 square feet of decking (assuming 6" wide boards, installed perpendicular to joists spaced 16" on center)

EB-TY® | Hidden Deck Fastening

Tapered Ipê Wood Plugs - see page 87

Model EBE002

Model EBE004

Model EBE005LC

Model EBE006JR

Model EBE007MI

Model 316-TS

Model 316-TT

Board Width/Joist Spacing

BoardThickness

BoardSpacing

#7 ScrewLength

EB-TYModel

Deck PackCount

Deck PackItem No.

6"/16" O.C. 1"+ 3⁄32" 2 1⁄4" EBE004 175 175-EBTYS

6"/16" O.C. 1"+ 3⁄32" 2 1⁄4" EBE004 175 175-EBTYW*

6"/24" O.C. 1"+ 3⁄32" 2 1⁄4" EBE004 100 100-EBTYS

4"/16" O.C. 1"+ 3⁄32" 2 1⁄4" EBE004 275 275-EBTYS

6"/16" O.C. 1"+ 3⁄32" 15⁄8" EBE004 175 175-EB162

6"/16" O.C. 1"+ 1⁄8" 2 1⁄4" EBE004 175 175-EBTYPV

6"/16" O.C. 1"+ 1⁄4" 2 1⁄4" EBE005LC 175 175-EBTYLC

6"/16" O.C. 1"+ 1⁄4" 2 1⁄4" EBE005LC 175 175-EBTYLW*

6"/24" O.C. 1"+ 1⁄4" 2 1⁄4" EBE005LC 100 100-EBTYLC

4"/16" O.C. 1"+ 1⁄4" 2 1⁄4" EBE005LC 275 275-EBTYLC

6"/16" O.C. 11⁄16"+ 3⁄32" 2 1⁄4" EBE007MI 175 175-EBTYMI

6"/24" O.C. 11⁄16"+ 3⁄32" 2 1⁄4" EBE007MI 100 100-EBTYMI

6"/16" O.C. 11⁄16"+ 1⁄4" 2 1⁄4" EBE006JR 175 175-EBTYJR

6"/16" O.C. 2"+ 1⁄4" 2 1⁄4" EBE002 175 175-EBTYBG

6"/16" O.C. 11⁄16"+ 3⁄16" 2 1⁄4" 316-TT 175 175-EBTT

6"/16" O.C. 11⁄16"+ 3⁄16" 2 1⁄4" 316-TS 175 175-EBTYP

*#7 trim-head Woodpeckers™ stainless-steel screws included – all others have #7 Swaneze™ trim-head screws included

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


29

DECKING EB-TY ® Hidden Deck Fastening

Helpful Hints and Facts

InstallationFasten the fi rst board using construction adhesive and screws, then cut slots where the 1. board intersects joists using a 5⁄32" router bit or plate joiner (biscuit cutter #20) and install the fi rst EB-TY fasteners. Do not use construction adhesive with composite decking (see right).

Cut slots in the next board where it intersects the joists. 2.

Apply a bead of construction adhesive to the top of each joist and install the new board 3. so that the slots fi t over the EB-TY fasteners installed in the fi rst board.

Insert EB-TY fasteners into each slot in the exposed edge of the board and fasten with screws.4.

Repeat the process until all boards are installed.5.

Refer to the installation instructions (included) for more information. Consult composite decking manufacturer’s or wood supplier’s installation instructions for deck height requirements and deck board spacing.

Pre-grooving the entire length of the deck board is a time-saving alternative to individual grooves made with a router or plate joiner. Some types of composite lumber are available with grooves as an added feature. Have your lumber yard use the schematic on the right to pregroove boards to accept EB-TY fasteners.

*For model numbers 316-TS and 316-TT screws are to be driven at a 90° angle to the board face.

Common Uses

If you have questions about which EB-TY to use, speak with one of our sales professionals today – we look forward to working with you!

EBE002True 1 1⁄2" material or thickerPopular in boardwalk construction

EBE0041" and 1 1⁄4" deck boardsIpê, Cedar, Redwood, stable composites

EBE005LC1" and 1 1⁄4" kiln-dried boardsBrazilian Redwood, some Mahogany, select composites

EBE006JR3⁄4" kiln-dried boardsBrazilian Redwood, some Mahogany, select composites

EBE007MI3⁄4" boardsIpê, Cedar, Redwood, stable composites

316-TSComposite decking, solid or pre-grooved

316-TTComposite decking, pre-grooved with a wider channel (e.g. Timber Tech®)

Construction adhesive is not recommended when installing composite deck boards as some adhesives will have an adverse reaction upon contact with certain plastics.

!

Bring the schematic below to your lumber yard. They will use it to pre-groove your decking material to accept EB-TY fasteners.0.500"

0.1630"

Cut groove at center of material thickness

EB-TYbiscuit fastener

Second deck board fastened with EB-TY and construction adhesive applied to top of fl oor joist

Fasten one side of fi rst deck board using screws and plugs

#7x 2 1⁄4" Swaneze trim head screw angled at 45°

• As with all decking materials, please consult manufacturer’s installation instructions for deck height requirements and deck board spacing.

• All slots for the EB-TY’s (except for the TT) can be cut using a #20 setting with a biscuit cutter/plate jointer or router with 5⁄32" slot cutter. Decking can be grooved the entire length of the board.

• Always butt boards over a joist. One method for installing butt ends is to cut the keel off the bottom of an EB-TY, slot the board ends, and insert the EB-TY. Another, more reliable method is to face-screw and plug.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


30

DECKING Flooring Cleats and Staples

• Ideal for tongue-and-groove decking

Gauge Length BoxCount Item No.

16 2" 1000 S16B200TNL

304 Stainless Steel

FLOORING CLEATS | “T” Series



16 1 1⁄2" 1000 S16B150LCT

16 2" 1000 S16B200LCT

304 Stainless Steel

FLOORING CLEATS | “L” Series

Compatible ToolsPorta-Nails® 401, 421, 501Primatech® H-300, H-330, P-210Senco® SHF15

Compatible Tools

Bostitch® MFN 200, MIIIFNPorter Cable® FCN 200Powernail® 45, 101, 445 SeriesPrimatech® H-300, H-330, P-210Senco® SHF15, SHF50



15 1⁄2 1 3⁄4" 5000 S15N175BFS

15 1⁄2 2" 5000 S15N200BFS

304 Stainless Steel, 1⁄2" Crown

FLOORING STAPLES | Similar to Bostitch® BCS Series

Compatible ToolsBostitch® MIIIFS

Did you know that all of our collated brads, fi nish nails, staples and cleats are treated with a special coating that is typically clear, but can also be yellow or green? Upon entry into wood this coating melts and acts as a lubricant. Once the fastener cools, the coating dries – acting as an adhesive to increase pull-out resistance.

!

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


31

SIDING

Fine Wood SidingWhether you’re siding with Cedar, Redwood or Cypress, you’ll fi nd that Simpson Strong-Tie carries the right fastener for the job. Fine wood siding offers natural beauty, dimensional stability, superior workability, and resistance to insect damage and decay given proper treatment and maintenance.

The slender gauge of our hand-drive stainless-steel wood siding nails limits splitting, and textured heads ensure a better blend with wood grains. Furthermore, our siding nails are available pre-painted to match various siding materials.

Note that we carry wire coil siding nails (also available pre-painted) compatible with a range of popular pneumatic nail guns.

Fiber Cement SidingFor siding offering strength, visual appeal and long-lasting durability regardless of climate, many builders today look to fi ber cement. Available in shingles, lap and panel profi les in a variety of textures, most fi ber cement siding products carry the added benefi t of transferable manufacturer’s warranties ranging from 25-50 years.

Our 316 stainless-steel Portland™ fi ber-cement hand-drive nails meet strict specifi cations currently required by most manufacturers of lap and panel fi ber cement. We also stock collated Portland nails for use with pneumatic nail guns. Our stainless-steel screws come in two versions: wood stud or metal stud. Both are manufactured expressly for fi ber cement applications and are self-countersinking to insure fl ush seating with work surfaces.

Fine WoodSiding

Fiber CementSiding

We stock a large selection of high quality, stainless-steel siding fasteners offering the combined benefi ts of strength, durability and corrosion resistance. You can count on Simpson Strong-Tie® Swan Secure products to endure the challenges of harsh environmental elements and time – in most cases outlasting the life of the siding itself. As always, we strongly recommend our AISI-graded 316 stainless-steel fasteners for seaside applications.

SIDING

Hand-Drive NailsWood Siding ................................................................................ 32Shake and Shingle ....................................................................... 32Painted Siding .............................................................................33Fiber-Cement Siding, Portland™ ..................................................34Pyramid Head Siding .................................................................. 34

Collated NailsWire Coil 15°, Ring-Shank, Siding ............................................... 35Wire Coil 15°, Ring-Shank, Fiber-Cement Siding .......................... 35Wire Coil 15°, Painted Siding ...................................................... 36Plastic Coil 15°, Siding ................................................................36Inserted Plastic Coil 15°, Siding .................................................. 37

Hand-Drive ScrewsFiber Cement, Fy-Cem™ – Wood Stud ........................................ 37Self-Drilling, Fy-Cem Billy Goats™ – Metal Stud .........................38Trim Head, Self-Drilling, Billy Goats™ – Metal Stud ..................... 38Hex Washer Head Panel, Twin Lead Thread ................................39K-Lath, Modifi ed Truss Head, Self-Drilling, Metal ......................40K-Lath, Modifi ed Truss Head, Wood ...........................................40

Collated StaplesSimilar To:Senco® “N” Series ....................................................................... 41Paslode® “GS” Series .................................................................. 41Paslode® “GSI” Series ................................................................. 42Bostitch® “BCS” Series ............................................................... 42

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


32

SIDING Hand-Drive Nails


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket


3d 1 1⁄4" 14 .083" 5⁄32" 495 S3SND25 S3SND5 S3SND1 S3SNDB



6d 2" 13 .095" 5⁄32" 245 S6SND25 S6SND5 S6SND1 S6SNDB







• Premium-quality nails for cedar, redwood and cypress siding• Slender gauge and blunt diamond point minimize splitting• Generous fi llet under nail head allows nails to be driven fl ush or countersunk without

crushing surrounding wood• Checker-patterned head blends with wood texture, serves to diffract sunlight

and accept surface fi nishes• Annular ring threads resist cupping of siding boards and nail-head popping• Choose type 316 for seaside applications and superior corrosion resistance• Bucket = 25 lbs.

HAND-DRIVE NAILS | Wood Siding


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket


3d 1 1⁄4" 14 .083" 7⁄32" 470 S3SN725 S3SN75 S3SN71 S3SN7B

4d 1 1⁄2" 14 .083" 7⁄32" 394 S4SN725 S4SN75 S4SN71 S4SN7B

5d 1 3⁄4" 14 .083" 7⁄32" 337 S5SN725 S5SN75 S5SN71 S5SN7B

6d 2" 13 .095" 7⁄32" 237 S6SN725 S6SN75 S6SN71 S6SN7B

7d 2 1⁄4" 13 .095" 7⁄32" 216 S7SN725 S7SN75 S7SN71 S7SN7B

8d 2 1⁄2" 13 .095" 7⁄32" 196 S8SN725 S8SN75 S8SN71 S8SN7B


HAND-DRIVE NAILS | Shake and Shingle




All of our hand-driven nails can be ordered passivated for a nominal up-charge. Passivation is a light acid bath that cleans the fastener of surface contaminants and aids in preventing premature corrosion.

!

• 7⁄32" diameter checker pattern fl at head provides ample bearing surface to fi rmly secure shakes and shingles of all types

• Slender shanks minimize splitting• Annular ring threads resist cupping, wind damage and nail-head popping• Choose type 316 for seaside applications and superior corrosion resistance

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


33



DiameterHead

Diameter Color Approx.Count per lb.

25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

Bucket Item No.

Availablein 316*

6d 2" 13 .095" 5⁄32" Cedar 245 S6SNDT25 S6SNDT5 S6SNDT1 S6SNDTB

6d 2" 13 .095" 5⁄32" Dark Brown 245 S6SNDB25 S6SNDB5 S6SNDB1 S6SNDBB

6d 2" 13 .095" 5⁄32" Gray 245 S6SNDG25 S6SNDG5 S6SNDG1 S6SNDGB

6d 2" 13 .095" 5⁄32" Redwood 245 S6SNDR25 S6SNDR5 S6SNDR1 S6SNDRB

6d 2" 13 .095" 5⁄32" White 245 S6SNDW25 S6SNDW5 S6SNDW1 S6SNDWB

8d 2 1⁄2" 13 .095" 5⁄32" Cedar 196 S8SNDT25 S8SNDT5 S8SNDT1 S8SNDTB

8d 2 1⁄2" 13 .095" 5⁄32" Dark Brown 196 S8SNDB25 S8SNDB5 S8SNDB1 S8SNDBB

8d 2 1⁄2" 13 .095" 5⁄32" Gray 196 S8SNDG25 S8SNDG5 S8SNDG1 S8SNDGB

8d 2 1⁄2" 13 .095" 5⁄32" Redwood 196 S8SNDR25 S8SNDR5 S8SNDR1 S8SNDRB

8d 2 1⁄2" 13 .095" 5⁄32" White 196 S8SNDW25 S8SNDW5 S8SNDW1 S8SNDWB

10d 3" 12 .109" 7⁄32" Cedar 120 S10SNDT25 S10SNDT5 S10SNDT1 S10SNDTB

10d 3" 12 .109" 7⁄32" Dark Brown 120 S10SNDB25 S10SNDB5 S10SNDB1 S10SNDBB

10d 3" 12 .109" 7⁄32" Gray 120 S10SNDG25 S10SNDG5 S10SNDG1 S10SNDGB

10d 3" 12 .109" 7⁄32" Redwood 120 S10SNDR25 S10SNDR5 S10SNDR1 S10SNDRB

10d 3" 12 .109" 7⁄32" White 120 S10SNDW25 S10SNDW5 S10SNDW1 S10SNDWB

• Premium-quality nails for cedar, redwood and cypress siding materials• Slender gauge and blunt diamond point minimize splitting• Generous fi llet under nail head allows nails to be driven fl ush or countersunk without

crushing surrounding wood• Checker-patterned head blends with wood texture and serves to diffract sunlight• Annular ring threads resist cupping of siding boards and nail-head popping• Custom colors available upon request (minimums apply) – call for details• Choose type 316 for seaside applications

and superior corrosion resistance• Bucket = 25 lbs.

HAND-DRIVE NAILS | Painted Siding



Hammer CapsWhen installing our painted siding nails, remember that our hammer caps are an inexpensive way to help preserve the painted fi nish.Model: HAMRCAP

!

Cedar Dark Brown Gray Redwood White

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


34



DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket

Item No.

3d 1 1⁄4" 11 .120" 11⁄32" 199 T3PCS25 T3PCS5 T3PCS1 T3PCSB


6d 2" 11 .120" 9⁄32" 144 T6PCS25 T6PCS5 T6PCS1 T6PCSB


• Designed expressly for application of various lap and panel siding materials made of fi ber cement composites

• Annular ring threads resist cupping of siding boards and nail-head popping• Extra-sharp point for optimum drivability• Generous fi llet under nail head allows nails to be driven fl ush with work surface• Checker-patterned head diffracts sunlight, accepts surface fi nishes• 1 1⁄4" roof head nails for blind-nailing lap siding, other sizes for face-nailing siding planks or panels• Recommended for seaside applications and superior corrosion resistance• Bucket = 25 lbs.

HAND-DRIVE NAILS | Portland™ Fiber-Cement Siding

316 Stainless Steel


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket


6d 2" 11 .120" 1⁄4" 144 I6PSN25 I6PSN5 I6PSN1 I6PSNB

8d 2 1⁄2" 11 .120" 1⁄4" 115 I8PSN25 I8PSN5 I8PSN1 I8PSNB

10d 3" 11 .120" 1⁄4" 99 I10PSN25 I10PSN5 I10PSN1 I10PSNB

16d 3 1⁄2" 11 .120" 1⁄4" 88 I16PSN25 I16PSN5 I16PSN1 I16PSNB

• “Pyramid” style decorative heads are reminiscent of old rose-head nails• Lends a rustic look to face-nailed lap, bevel and board and batten siding jobs• Annular ring threads hold fast in wood substrates• 316 stainless-steel nails highly visible on darker siding materials• Silicon bronze weathers to dark brown color• Bucket = 25 lbs.

HAND-DRIVE NAILS | Pyramid Head

Silicon Bronze and 316 Stainless Steel


BEVEL SIDING INSTALLATION CALCULATOR

Nominal Width Exposed Face Overlap Nail Count FactorLinear Foot

Nail Count FactorSquare Foot

4 2 1⁄2 1 0.75 3.60

6 4 1⁄2 1 0.75 2.03

8 6 1⁄2 1 1⁄8 0.75 1.43

10 8 1⁄2 1 1⁄2 0.75 1.13

12 10 1⁄2 1 1⁄2 0.75 0.90

How To Figure:Multiply the linear feet or square feet by the nail count factor above. The result is the quantity of nails required.• One (1) nail per stud – 16" on center• Allowance for waste and loss should be added

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


35

SIDING Collated Nails

• Protect your investment in fi ne wood siding from hard-to-remove stains and streaks • Premium-quality nails for cedar, redwood and cypress siding materials• Slender gauge and blunt diamond point minimize splitting• Generous under-head fi llet allows nails to be driven fl ush, or countersunk,

without crushing surrounding wood • Checker-patterned head blends with wood texture and serves to diffract sunlight• Annular ring threads resist cupping of siding boards and nail-head popping• Choose type 316 for seaside applications and superior corrosion resistance


HeadDiameter

BoxCount Item No.

1 1⁄4" .090" 13⁄64" 3600 S13A125SNC

1 1⁄2" .090" 13⁄64" 3600 S13A150SNC

1 3⁄4" .090" 13⁄64" 3600 S13A175SNC

2" .090" 13⁄64" 3600 S13A200SNC

2 3⁄16" .090" 13⁄64" 3600 S13A219SNC

2 1⁄2" .090" 13⁄64" 3600 S13A250SNC

304 Stainless Steel



HeadDiameter

BoxCount Item No.

1 1⁄2" .090" 13⁄64" 1800 T13A150SNJ

1 3⁄4" .090" 13⁄64" 1800 T13A175SNJ

2" .090" 13⁄64" 1800 T13A200SNJ

2 3⁄16" .090" 13⁄64" 1800 T13A219SNJ

2 1⁄2" .090" 13⁄64" 1800 T13A250SNJ

316 Stainless Steel

Compatible Pneumatic ToolsBostitch® N63CP, N64C, N65CP, N66CHitachi® NV65AH, NV65ACMAX® CN565, CN565S, CN70 (1 3⁄4" TO 2 3⁄4"), CN55 (1" TO 2 1⁄4")Paslode® 3225/CN55Senco® SCN55S

COLLATED NAILS | Wire Coil 15°, Ring Shank, Fiber-Cement Siding


HeadDiameter

BoxCount Item No.

1 1⁄2" .093" .225" 3600 S13A150SNA

1 3⁄4" .093" .225" 3600 S13A175SNA

2" .093" .225" 3600 S13A200SNA

2 3⁄16" .093" .225" 3600 S13A219SNA

2 1⁄2" .093" .225" 3600 S13A250SNA

304 Stainless Steel

Your Nail Gun, Our FastenersTool manufacturers are constantly introducing new tools to the market. If you don’t see your particular model in our tool compatibility listings, visit www.strongtie.com or call any of our locations and a sales professional will assist you in your fastener selection.

!

Stainless-Steel Wire CollationBeware of collated nails that do not specify either AISI grade 304 or 316 stainless steel. If the alloy is not printed on the box or label, you don’t know what you are getting. There are several stainless-steel alloys from which fasteners can be made – 304 and 316 being the most common used in nail production. However, some distributors have recentlyresorted to selling inferior alloys resulting in nails that fail to offer the corrosion resistance and strength our customers have come to expect. Furthermore, be certain that the wire collation medium holding the nails together is also stainless steel – Simpson Strong-Tie only sells Swan Secure nails with stainless-steel collation medium.

!

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


36

SIDING Collated Nails

• Protect your investment in fi ne wood siding from hard-to-remove stains and streaks • Premium-quality nails for cedar, redwood and cypress siding materials• Stainless steel will last the life of wood siding without degrading in most environments• Slender gauge and blunt diamond point minimize splitting• Generous under-head fi llet allows nails to be driven fl ush, or countersunk,

without crushing surrounding wood • Checker-patterned head blends with wood texture and serves to diffract sunlight• Annular ring threads limit

cupping of siding boards and nail-head popping


HeadSize Color Box

Count Item No.

2" .090" 13⁄64" Dark Brown 3600 S13A200CCB

2" .090" 13⁄64" Gray 3600 S13A200CCG

2" .090" 13⁄64" Redwood 3600 S13A200CCR

2" .090" 13⁄64" Cedar 3600 S13A200CCT

2" .090" 13⁄64" White 3600 S13A200CWH

2 3⁄16" .090" 13⁄64" Dark Brown 3600 S13A219SNB

2 3⁄16" .090" 13⁄64" White 3600 S13A219SNW

2 3⁄16" .090" 13⁄64" Gray 3600 S13A219SNG

2 3⁄16" .090" 13⁄64" Redwood 3600 S13A219SNR

2 3⁄16" .090" 13⁄64" Cedar 3600 S13A219SNT

2 1⁄2" .090" 13⁄64" Dark Brown 3600 S13A250CCB

2 1⁄2" .090" 13⁄64" Gray 3600 S13A250CCG

2 1⁄2" .090" 13⁄64" Redwood 3600 S13A250CCR

2 1⁄2" .090" 13⁄64" Cedar 3600 S13A250CCT

2 1⁄2" .090" 13⁄64" White 3600 S13A250CWH

COLLATED NAILS | Wire Coil 15°, Painted

Compatible Pneumatic Tools Bostitch® N63CP, N64C, N65CP, N66CHitachi® NV65AH, NV65ACMAX® CN565, CN565S, CN70 (1 3⁄4" TO 2 3⁄4"), CN55 (1" TO 2 1⁄4")Paslode® 3225/CN55Senco® SCN55S

COLLATED NAIL | Plastic Coil 15°

Compatible Pneumatic ToolsHitachi® NV50AA, VH650, VH500

Size Length Gauge ShankDiameter

HeadDiameter

BoxCount Item No.

5d 1 3⁄4" 14 .086" .203" 4000 S14A175SNC

6d 2" 14 .086" .203" 4000 S14A200SNC

304 Stainless Steel for Hitachi®

304 Stainless Steel Cedar Dark Brown Gray Redwood White

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


37

SIDING Collated Nails / Hand-Drive Screws


HeadDiameter


in 316*

4d 1 1⁄2" 13 .095" .203" 3200 S13A150IPC

5d 1 3⁄4" 13 .095" .203" 3200 S13A175IPC

6d 2" 13 .095" .203" 3200 S13A200IPC

7d 2 1⁄4" 13 .095" .203" 2400 S13A225IPC

8d 2 1⁄2" 13 .095" .203" 2400 S13A250IPC

• Choose type 316 for seaside applications and superior corrosion resistance


COLLATED NAILS | Inserted Plastic Coil 15°

Compatible Pneumatic Tools Bostitch® N63CP, N66CHitachi® NV65AH, NV65AE, NV75AG (.099" to .131" 1 3⁄4" to 3")Makita® AN611MAX® CN565, CN565S (1 1⁄2" to 2 1⁄2")Paslode® 4250-6C-PSenco® SCN55S



HeadDiameter

BoxCount Item No.

8d 2 1⁄2" 13 .095" .203" 2400 I13A250IPC

Silicon Bronze


HeadDiameter

BoxCount Item No.

5d 1 3⁄4" 12 .099" .210" 9000 S12A175DNB

7d 2 1⁄4" 12 .099" .210" 7200 S12A225DNB

304 Stainless Steel for Duofast Model KDN50

Compatible Pneumatic ToolsDuofast® KDN50, RCN60, RCN70, CNP-60Y, CNP-65Y

Size Length Head Diameter Carton Count Item No.

#8 1 1⁄4" .390" 100 T08C125WQC

#8 1 1⁄4" .390" 1000 T08C125WQM

#8 1 5⁄8" .390" 100 T08C162WQC

#8 1 5⁄8" .390" 1000 T08C162WQM

#8 2 1⁄4" .390" 1000 T08C225WQM

#8 2 1⁄4" .390" 2000 T08C225WQC

316 Stainless Steel

• #2 square drive, coarse thread full length• Type-17 point for fast starts • Self-countersinking nibs under head insure seating of screw head fl ush with work surface• Threaded to within 5⁄16" of head• Use 1 1⁄4" screws to attach fi ber cement siding to stress skin panels• Use 1 5⁄8" screws to blind-fasten fi ber cement lap siding to wood

HAND-DRIVE SCREWS | FY-CEM™ Fiber Cement, Wood Stud

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


38

SIDING Hand-Drive Screws

• Fasten fi ber cement through furring strips to steel studs• #2 square drive wafer head, #3 drill point • Self-countersinking nibs under head insure seating of screw head fl ush with work surface• Threaded to within 5⁄16" of top of head• Drilling thickness capacity: up to 0.142" (118 mils or 10 ga.)

HAND-DRIVE SCREWS | FY-CEM™ Billy Goats™, Self Drilling, Fiber-Cement, Metal Stud


CartonCount Item No.

#8 1 5⁄8" .390" 100 F08T162WDC

#8 1 5⁄8" .390" 1000 F08T162WDM

#8 1 5⁄8" .390" 3000 F08T162WDB

#8 2 1⁄4" .390" 100 F08T225WDC

#8 2 1⁄4" .390" 1000 F08T225WDM

#8 2 1⁄4" .390" 2500 F08T225WDB

410 Stainless-Steel Wafer Head Self-Drilling

• Attach wood siding, wood panels and metal trim to steel studs• #1 square drive trim head, .230" head diameter, #3 drill point • Threaded 2⁄3 of overall length• Drilling thickness capacity: up to 0.125" (111 mils or 11 ga.)

HAND-DRIVE SCREWS | Billy Goats™, Self Drilling, Trim Head, Metal Stud



#7 1 5⁄8" 187 100 F07T162TDC

#7 1 5⁄8" 187 1000 F07T162TDM

#7 1 5⁄8" 187 5000 F07T162TDB

#7 2 1⁄4" 132 100 F07T225TDC

#7 2 1⁄4" 132 1000 F07T225TDM

#7 2 1⁄4" 132 4000 F07T225TDB

#7 3" 105 100 F07T300TDC

#7 3" 105 1000 F07T300TDM

#7 3" 105 2000 F07T300TDB

410 Stainless-Steel Trim Head Self-Drilling

Type 410 stainless steel can be hardened through heat treatment, giving it the ability to drill through metal.It does not offer the same level of corrosion resistance or either type 305 or 316 stainless steel.


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


39


• Fasten aluminum agricultural siding panels to wood joists without pre-drilling

• Extra-sharp point for quick penetration of aluminum panels without “point walking” • Twin-lead thread fastens one to three panel thicknesses securely to wood substrate• 5⁄16" Hex drive• Panel screws available with and without aluminum/neoprene bonded sealing washers

HAND-DRIVE SCREWS | Twin-Lead Hex-Washer Head

Size Length CartonCount Item No. Available

in 316*

#9 1" 100 S09T100HWHC

#9 1" 1000 S09T100HWHM

#9 1 1⁄2" 100 S09T150HWHC

#9 1 1⁄2" 1000 S09T150HWHM

#9 2" 100 S09T200HWHC

#9 2" 1000 S09T200HWHM

#9 2 1⁄2" 100 S09T250HWHC —

#9 2 1⁄2" 1000 S09T250HWHM —

#9 3" 100 S09T300HWHC —

#9 3" 1000 S09T300HWHM —


in 316*

#9 1" 100 S09100HWAC

#9 1" 1000 S09100HWAM

#9 1 1⁄2" 100 S09150HWAC

#9 1 1⁄2" 1000 S09150HWAM

#9 2" 100 S09200HWAC

#9 2" 1000 S09200HWAM

#9 2 1⁄2" 100 S09250HWAC —

#9 2 1⁄2" 1000 S09250HWAM —

#9 3" 100 S09300HWAC —

#9 3" 1000 S09300HWAM —

18-8 and 316 Stainless Steel

18-8 and 316 Stainless Steel with Neoprene-Bonded Washer



Also available with neoprene-bonded washers

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


40


HAND-DRIVE SCREWS | K-Lath Modifi ed Truss Head, Self-Drilling

Size Length CartonCount Item No.

#8 9⁄16" 100 F08T056KDC

#8 9⁄16" 1000 F08T056KDM

#8 9⁄16" 8000 F08T056KDB

#8 3⁄4" 100 F08T075KDC

#8 3⁄4" 1000 F08T075KDM

#8 3⁄4" 6000 F08T075KDB

#8 1 1⁄4" 100 F08T125KDC

#8 1 1⁄4" 1000 F08T125KDM

#8 1 1⁄4" 4000 F08T125KDB

#8 1 5⁄8" 100 F08T162KDC

#8 1 5⁄8" 1000 F08T162KDM

#8 1 5⁄8" 3000 F08T162KDB

#8 2" 100 F08T200KDC

#8 2" 1000 F08T200KDM

#8 2" 2500 F08T200KDB

410 Stainless Steel

HAND-DRIVE SCREWS | K-Lath Modifi ed Truss Head, Wood


#8 3⁄4" 100 S08C075KQC

#8 3⁄4" 1000 S08C075KQM

#8 1 1⁄4" 100 S08C125KQC

#8 1 1⁄4" 1000 S08C125KQM

305 Stainless Steel

• For use in applications where a larger bearing surface is needed underneath the head

• Used to fasten lath to wood • Type-17 point for fast starts• #2 Phillips drive

• Fastens corrugated siding panels to steel stud without pre-drilling• #3 drill point for quick penetration of aluminum panels without “point walking” • Securely fastens one to three panel thicknesses• #2 Phillips drive• Drilling thickness capacity: up to 0.142" (118 mils or 10 ga.)


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


41

SIDING Collated Staples

Gauge Length CartonCount Item No. Available

in 316*

16 1 1⁄4" 10,000 S16N125GS

16 1 1⁄2" 10,000 S16N150GS

16 1 3⁄4" 10,000 S16N175GS

304 and 316 Stainless Steel, 1/2" Crown

COLLATED STAPLES | Similar to Paslode® “GS” Series

Compatible Pneumatic Tools Fasco® GSPaslode® IM200-S16, 4200-S16 & 3200-S16P, 3150-S16 (3⁄4" to 1 1⁄2")



in 316*

16 3⁄4" 5000 T16N075N11 **16 1" 5000 S16N100N13

16 1 1⁄4" 5000 S16N125N15

16 1 1⁄2" 5000 S16N150N17

16 1 3⁄4" 5000 S16N175N19

16 2" 5000 S16N200N21


COLLATED STAPLES | Similar to Senco® “N” Series

Compatible Pneumatic ToolsBostitch® 650S5Hitachi® N5008AA & A1, N5008AB & N5008ACFasco® GMax® TA551/16-11 (1" to 2")Porter Cable® CMS200 & MS200Senco® M1 (3⁄4" -1 3⁄4"), SNS45 (1" -2"), SNS50 (1 1⁄4" -2"), SKS (3⁄4" to 1 1⁄2" ),

M2+ (1 1⁄4" to 2"), SNS45 (1" to 2")


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


42

SIDING Collated Staples

Gauge Length CartonCount Item No.

16 1 1⁄4" 10,000 S16N125GSI

16 1 1⁄2" 10,000 S16N150GSI

304 Stainless Steel, 7/16" Crown

COLLATED STAPLES | Similar to Paslode® “GSI” Series

Compatible Pneumatic ToolsDuoFast® 76 Series Stapler (1 1⁄4" -1 1⁄2")Paslode® 3200-I16 (1 1⁄4" -1 1⁄2"), 3150-I16 (1 1⁄4" -1 1⁄2"), MU112-I16 (1 1⁄4")


16 1 1⁄4" 10,000 T16N125B07

16 1 1⁄2" 10,000 T16N150B09

16 1 3⁄4" 10,000 T16N175B11

16 2" 10,000 T16N200B13


COLLATED STAPLES | Similar to Bostitch® “BCS” Series

Compatible Pneumatic ToolsBostitch® T36-1, T36-50, T50S4-1 & T55S4-1 (3⁄4" -1 3⁄4"), 438S2R (1⁄2" -1 1⁄2"), T40S4-CT (3⁄4" to 1 1⁄2") , 438S4, 650S4Fasco® HD

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


43

ROOFING

SlateChoose from our selection of hand-drive stainless-steel or copper roofi ng nails when fastening this natural stone material that has been used for centuries to provide long lasting elegant beauty and stability.

Composite SlateToday’s synthetic slate offers the appeal of real slate in terms of color, texture, light weight and long service. Our stainless-steel hand-drive and collated roofi ng nails are your best bet for fastening this type of roofi ng.

Wood ShingleIf you’re roofi ng with cedar or pressure treated pine, you’ll fi nd our stainless-steel hand-drive shake/shingle nails to be your best option for the job. They’re also available in a wire coil collated confi guration, compatible with a variety of pneumatic nail guns.

Standing Seam and Corrugated PanelWe offer low-profi le pancake head screws specifi cally designed for fastening standing seam roofi ng to either wood stud or metal stud. Look to our twin-lead thread, hex head screws for aluminum and fi berglass corrugated panel installation.

ROOFING

Slate

Composite Slate

Simpson Strong-Tie offers a wide array of Swan Secure hand-drive and collated nails, screws, and staples for fastening roofi ng materials of all types. Whether it’s slate, asphalt shingle, tile, cedar shake, standing seam copper or corrugated roofi ng, we’ve got you covered.

Wood Shingle

Standing SeamCorrugated Panel

Hand-Drive NailsRoofi ng/Slating, Copper ............................................... 44Roofi ng/Slating, Stainless ............................................ 45Roofi ng/Slating, Aluminum........................................... 45Shake and Shingle ........................................................ 46Washered Roofi ng, Stainless ........................................ 46Tile/Slate, Copper ...........................................................47Tile/Slate, Stainless ....................................................... 48Gutter Spikes ................................................................. 48

Collated NailsWire-Coil Collated, Roofi ng .......................................... 49

Collated StaplesSimilar To:Senco® “L” Series .......................................................... 50Senco® “N” Series ......................................................... 50Senco® “P” Series ..........................................................51Paslode® “GS” Series .....................................................51Bostitch® “BCS” Series ..................................................51

Hand-Drive ScrewsTruss Head, Self-Drilling ................................................ 52 Hex Washer Panel ......................................................... 52Pancake/Clip, Square Drive, Self-Drilling ..................... 53Pancake/Clip, Square Drive, Type “A” Point ................. 53Gutter Screws, Hex Socket Drive .................................. 53

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


44

ROOFING Hand-Drive Nails

• Large fl at head, regular diamond point• Copper roofi ng nails are also commonly referred to as slating nails• Annular ring shank nails offer superior holding power in plywood roof decks• For slate roofs choose nail length by adding one inch to twice the thickness of slate• Bucket = 25 lbs.

HAND-DRIVE NAILS | Roofi ng/Slating, Copper

Length Gauge ShankDiameter

HeadDiameter


25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

Bucket Item No.

3⁄4" 11 .120" 3⁄8" 302 C7511ARN25 C7511ARN5 C7511ARN1 C7511ARNB

1" 10 .134" 7⁄16" 187 C210ARN25 C210ARN5 C210ARN1 C210ARNB


1 1⁄4" 10 .134" 7⁄16" 147 C310ARN25 C310ARN5 C310ARN1 C310ARNB











Annular Ring Shank Copper


HeadDiameter


25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

Bucket Item No.

3⁄4" 11 .120" 3⁄8" 302 C7511RN25 C7511RN5 C7511RN1 C7511RNB

1" 10 .134" 7⁄16" 187 C210RN25 C210RN5 C210RN1 C210RNB

1" 11 .120" 3⁄8" 229 C211RN25 C211RN5 C211RN1 C211RNB

1 1⁄4" 10 .134" 7⁄16" 147 C310RN25 C310RN5 C310RN1 C310RNB

1 1⁄4" 11 .120" 3⁄8" 187 C311RN25 C311RN5 C311RN1 C311RNB

1 1⁄2" 10 .134" 7⁄16" 123 C410RN25 C410RN5 C410RN1 C410RNB

1 1⁄2" 11 .120" 3⁄8" 155 C411RN25 C411RN5 C411RN1 C411RNB

1 3⁄4" 10 .134" 7⁄16" 112 C510RN25 C510RN5 C510RN1 C510RNB

1 3⁄4" 11 .120" 3⁄8" 139 C511RN25 C511RN5 C511RN1 C511RNB

2" 10 .134" 7⁄16" 93 C610RN25 C610RN5 C610RN1 C610RNB

2" 11 .120" 3⁄8" 124 C611RN25 C611RN5 C611RN1 C611RNB

2 1⁄2" 10 .134" 7⁄16" 81 C810RN25 C810RN5 C810RN1 C810RNB

2 1⁄2" 11 .120" 3⁄8" 108 C811RN25 C811RN5 C811RN1 C811RNB

3" 10 .134" 7⁄16" 67 C1010RN25 C1010RN5 C1010RN1 C1010RNB

Smooth Shank Copper

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


45


HAND-DRIVE NAILS | Roofi ng/Slating, Aluminum

Aluminum, Annular Ring Shank


HeadDiameter


25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

1" 11 .120" 3⁄8" 810 A211RN25 A211RN5 A211RN1

1 1⁄4" 11 .120" 3⁄8" 686 A311RN25 A311RN5 A311RN1

1 1⁄2" 11 .120" 3⁄8" 577 A411RN25 A411RN5 A411RN1

1 1⁄4" 9 .148" 7⁄16" 440 A39RN25 A39RN5 A39RN1

1 1⁄2" 9 .148" 7⁄16" 374 A49RN25 A49RN5 A49RN1

2" 9 .148" 7⁄16" 288 A69RN25 A69RN5 A69RN1

Aluminum, Smooth Shank


HeadDiameter


25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

1" 11 .120" 3⁄8" 810 A211ARN25 A211ARN5 A211ARN1

1 1⁄4" 11 .120" 3⁄8" 686 A311ARN25 A311ARN5 A311ARN1

1 1⁄2" 11 .120" 3⁄8" 577 A411ARN25 A411ARN5 A411ARN1

1 1⁄4" 9 .148" 7⁄16" 440 A39ARN25 A39ARN5 A39ARN1

1 1⁄2" 9 .148" 7⁄16" 374 A49ARN25 A49ARN5 A49ARN1

2" 9 .148" 7⁄16" 288 A69ARN25 A69ARN5 A69ARN1


HeadDiameter


25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

Bucket Item No.

Availablein 316*

3⁄4" 10 .134" 3⁄8" 281 S7510ARN25 S7510ARN5 S7510ARN1 S7510ARNB

1" 10 .134" 3⁄8" 212 S210ARN25 S210ARN5 S210ARN1 S210ARNB

1 1⁄4" 10 .134" 3⁄8" 166 S310ARN25 S310ARN5 S310ARN1 S310ARNB










HAND-DRIVE NAILS | Roofi ng/Slating, Stainless Steel

304 and 316 Stainless Steel, Annular Ring Shank


• Large fl at head, regular diamond point• Annular ring shank nails offer superior holding power in wood and plywood roof decks• For slate roofs choose nail length by adding one inch to twice the thickness of slate• Smooth shank available – when ordering, remove “A” from listed part numbers below• Bucket = 25 lbs.

• Large fl at head, regular diamond point• Spiral shank available upon request – call for details

We are proud of the fact that our nails were chosen to install the slate roofi ng at the University of Notre Dame.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


46



DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket


3d 1 1⁄4" 14 .083" 7⁄32" 470 S3SN725 S3SN75 S3SN71 S3SN7B

4d 1 1⁄2" 14 .083" 7⁄32" 394 S4SN725 S4SN75 S4SN71 S4SN7B

5d 1 3⁄4" 14 .083" 7⁄32" 337 S5SN725 S5SN75 S5SN71 S5SN7B

6d 2" 13 .095" 7⁄32" 237 S6SN725 S6SN75 S6SN71 S6SN7B

7d 2 1⁄4" 13 .095" 7⁄32" 216 S7SN725 S7SN75 S7SN71 S7SN7B

8d 2 1⁄2" 13 .095" 7⁄32" 196 S8SN725 S8SN75 S8SN71 S8SN7B

• 7⁄32" diameter checker-patterned fl at head provides ample bearing surface to fi rmly secure shakes and shingles of all types

• Slender shanks minimize splitting• Annular ring threads insure against wind damage and nail-head popping• Choose type 316 for seaside applications and superior corrosion resistance• Bucket = 25 lbs.

HAND-DRIVE NAILS | Shake and Shingle




HeadDiameter


25 lb. Item No.

5 lb. Item No.

1¼" 10 .134" 3⁄8" 121 S10125RNW25 S10125RNW5

1½" 10 .134" 3⁄8" 113 S10150RNW25 S10150RNW5

1¾" 10 .134" 3⁄8" 105 S10175RNW25 S10175RNW5

2" 10 .134" 3⁄8" 98 S10200RNW25 S10200RNW5

2¼" 10 .134" 3⁄8" 91 S10225RNW25 S10225RNW5

2½" 10 .134" 3⁄8" 83 S10250RNW25 S10250RNW5

3" 10 .134" 3⁄8" 72 S10300RNW25 S10300RNW5

3½" 10 .134" 3⁄8" 62 S10350RNW25 S10350RNW5

4" 10 .134" 3⁄8" 53 S10400RNW25 S10400RNW5

• Annular ring thread, large checkered head, heavy EPDM washers assembled• Best for application of corrugated panel roofi ng, particularly in corrosive environments• Also the recommended fastener for sheet metal roofi ng and siding• Standard washer dimensions: 9⁄16" O.D. x 1⁄8" thick• Large, resilient EPDM washers provide weather-tight fastening

HAND-DRIVE NAILS | Washered Roofi ng

Annular Ring Shank 304 Stainless Steel

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


47



HeadDiameter


25 lb. Item No.

5 lb. Item No.

3" 9 .148" 15⁄32" 57 C10ATN25 C10ATN5

3 1⁄2" 10 .134" 7⁄16" 59 C16ATN25 C16ATN5

3 1⁄2" 9 .148" 15⁄32" 48 C16HATN25 C16HATN5

4" 9 .148" 15⁄32" 43 C20ATN25 C20ATN5

5" 8 .165" 1⁄2" 28 C40ATN25 C40ATN5

5 1⁄2" 8 .165" 1⁄2" 25 C50ATN25 C50ATN5

6" 8 .165" 1⁄2" 23 C60ATN25 C60ATN5

• Large fl at head, diamond point• Annular ring threads offer greater pull-out resistance• Long nails expressly for installing curved Spanish roof tiles and slate

HAND-DRIVE NAILS | Tile/Slate, Copper

Annular Ring Shank Copper


HeadDiameter


25 lb. Item No.

5 lb. Item No.

3" 9 .148" 15⁄32" 57 C10TN25 C10TN5

3 1⁄2" 10 .134" 7⁄16" 59 C16TN25 C16TN5

3 1⁄2" 9 .148" 15⁄32" 48 C16HTN25 C16HTN5

4" 9 .148" 15⁄32" 43 C20TN25 C20TN5

5" 8 .165" 1⁄2" 28 C40TN25 C40TN5

5 1⁄2" 8 .165" 1⁄2" 25 C50TN25 C50TN5

6" 8 .165" 1⁄2" 23 C60TN25 C60TN5

Smooth Shank Copper

Copper slating nails are the roofer’s fastener of choice when it comes to slate roof repair. When a slate needs replacement, the roofer uses a slate ripper which is a tool that cuts the nails so that the broken slate can then be removed. Copper nails, being softer than stainless steel are much easier to cut.

!

We are proud to have contributed to the post-9/11 Pentagon re-roofi ng by donating copper slating nails to Meyers Roofi ng through our relationship with the National Roofi ng Contractor’s Association.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


48



HeadDiameter


25 lb. Item No.

5 lb. Item No.

3" 9 .148" 15⁄32" 57 S10ATN25 S10ATN5

3 1⁄2" 10 .134" 7⁄16" 59 S16ATN25 S16ATN5

3 1⁄2" 9 .148" 15⁄32" 48 S16HATN25 S16HATN5

4" 9 .148" 15⁄32" 43 S20ATN25 S20ATN5

5" 8 .165" 1⁄2" 28 S40ATN25 S40ATN5

5 1⁄2" 8 .165" 1⁄2" 25 S50ATN25 S50ATN5

6" 8 .165" 1⁄2" 23 S60ATN25 S60ATN5

• Long nails expressly for installing curved Spanish roof tiles and slate• Large fl at head, smooth shank, diamond point• Annular ring threads offer greater pull-out resistance• Available in 316 stainless steel – call for details

HAND-DRIVE NAILS | Tile/Slate, Stainless Steel

Annular Ring Shank 304 Stainless Steel


HeadDiameter


25 lb. Item No.

5 lb. Item No.

3" 9 .148" 15⁄32" 57 S10TN25 S10TN5

3 1⁄2" 10 .134" 7⁄16" 59 S16TN25 S16TN5

3 1⁄2" 9 .148" 15⁄32" 48 S16HTN25 S16HTN5

4" 9 .148" 15⁄32" 43 S20TN25 S20TN5

5" 8 .165" 1⁄2" 28 S40TN25 S40TN5

5 1⁄2" 8 .165" 1⁄2" 25 S50TN25 S50TN5

6" 8 .165" 1⁄2" 23 S60TN25 S60TN5

Smooth Shank 304 Stainless Steel


HeadDiameter


25 lb. Item No.

5 lb. Item No.

7" .238" 15⁄32" 10 C7S25 C7S5

8" .238" 15⁄32" 9 C8S25 C8S5

9" .238" 15⁄32" 8 C9S25 C9S5

10" .238" 15⁄32" 6 C10S25 C10S5

• Dimpled fl at head, barbed shank, diamond point• Stainless steel available in select sizes - call for availablity

HAND-DRIVE NAILS | Gutter Spikes

Copper

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


49

ROOFING Collated Nails

COLLATED NAILS | Roofi ng, Wire Coil 15°


HeadDiameter

BoxCount Item No.

1" .120" 3⁄8" 7200 S11A100RNB

1 1⁄4" .120" 3⁄8" 7200 S11A125RNB

1 1⁄4" .120" 3⁄8" 2400 S11A125RNJ

1 1⁄2" .120" 3⁄8" 7200 S11A150RNB

1 1⁄2" .120" 3⁄8" 2400 S11A150RNJ

1 3⁄4" .120" 3⁄8" 7200 S11A175RNB

1 3⁄4" .120" 3⁄8" 2400 S11A175RNJ

304 Stainless Steel, Ring Shank

Compatible Pneumatic Tools Bostitch® N12-1 (1 1⁄4" to 1 3⁄4"),

N12B, RN45B, RN46 Craftsman® 18455Hitachi® NV45AB , NV45AB2Makita® AN451MAX® CN450R, CN12RPaslode® 3175RCU, 3175/44 RCU Porter Cable® 134R & RN175Senco® SCN200R & SCN40R

(3⁄4" to 1 1⁄2")Stan-Tech® SDCN10-1


HeadDiameter

BoxCount Item No.

1" .120" 3⁄8" 3600 T11A100RNJ

1 1⁄4" .120" 3⁄8" 3600 T11A125RNJ

1 1⁄2" .120" 3⁄8" 3600 T11A150RNJ

1 3⁄4" .120" 3⁄8" 3600 T11A175RNJ

316 Stainless Steel, Ring Shank

• Large fl at head, regular diamond point• Great for asphalt and synthetic slate roofi ng• Annular ring threads offer greater pull-out resistance• Choose type 316 for seaside applications and superior corrosion resistance


HeadDiameter

BoxCount Item No.

3⁄4" .120" 3⁄8" 7200 S11N075RNB7⁄8" .120" 3⁄8" 7200 S11N087RNB

1" .120" 3⁄8" 7200 S11N100RNB

1" .120" 3⁄8" 2400 S11N100RNJ

1 1⁄4" .120" 3⁄8" 7200 S11N125RNB

1 1⁄4" .120" 3⁄8" 2400 S11N125RNJ

1 1⁄2" .120" 3⁄8" 7200 S11N150RNB

1 1⁄2" .120" 3⁄8" 2400 S11N150RNJ

1 3⁄4" .120" 3⁄8" 7200 S11N175RNB

1 3⁄4" .120" 3⁄8" 2400 S11N175RNJ

304 Stainless Steel, Smooth Shank


HeadDiameter

BoxCount Item No.

1" .120" 3⁄8" 3600 T11N100RNJ

1 1⁄4" .120" 3⁄8" 3600 T11N125RNJ

1 1⁄2" .120" 3⁄8" 3600 T11N150RNJ

1 3⁄4" .120" 3⁄8" 3600 T11N175RNJ

316 Stainless Steel, Smooth Shank

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


50

ROOFING Collated Staples


in 316*

18 5⁄8" 5000 S18N062L10

18 3⁄4" 5000 T18N075L11 **18 1" 5000 S18N100L13

18 1 1⁄8" 5000 S18N112L14

18 1 1⁄4" 5000 S18N125L15

18 1 1⁄2" 5000 S18N150L17


COLLATED STAPLES | Similar to Senco® “L” Series

Compatible Pneumatic Tools Duo-Fast® KN-1848AGrizzly® G6043Haubold® PN6040HHilti® SN-114B, SN-118Hitachi® N3804A, N3804AA & N3804ABPorter Cable® NS100 (1⁄2" to 1") NS150 (1⁄2" to 1 1⁄2")Senco® FinishPro 2N1 (1⁄4" -1"), SLS15 (5⁄8" to 1"), SLS18 (1⁄2" to 1 1⁄2"), SLS20,

SLS25XP (3⁄8" to 1 1⁄2"), SKSL12-17 (7⁄8" to 1 1⁄2"), SKSL11-15 (3⁄4" to 1 1⁄4")



in 316*

16 3⁄4" 5000 T16N075N11 **16 1" 5000 S16N100N13

16 1 1⁄4" 5000 S16N125N15

16 1 1⁄2" 5000 S16N150N17

16 1 3⁄4" 5000 S16N175N19

16 2" 5000 S16N200N21



Compatible Pneumatic ToolsBostitch® 650S5Hitachi® N5008AA & A1, N5008AB & N5008ACFasco® GMax® TA551/16-11 (1" to 2")Porter Cable® CMS200 & MS200Senco® M1 (3⁄4" -1 3⁄4"), SNS45 (1" -2"), SNS50 (1 1⁄4" -2"), SKS (3⁄4" to 1 1⁄2" ),

M2+ (1 1⁄4" to 2" ), SNS45 (1" to 2")


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


51

ROOFING Collated Staples


in 316*

16 1 1⁄4" 10,000 S16N125GS

16 1 1⁄2" 10,000 S16N150GS

16 1 3⁄4" 10,000 S16N175GS

16 2" 10,000 S16N200GS



Compatible Pneumatic Tools Fasco® GSPaslode® IM200-S16, 4200-S16 & 3200-S16P, 3150-S16 (3⁄4" to 1 1⁄2")



16 1 1⁄4" 10,000 T16N125B07

16 1 1⁄2" 10,000 T16N150B09

16 1 3⁄4" 10,000 T16N175B11

16 2" 10,000 T16N200B13



Compatible Pneumatic ToolsBostitch® T36-1, T36-50, T50S4-1 & T55S4-1 (3⁄4" -1 3⁄4"), 438S2R (1⁄2" to 1 1⁄2"), T40S4-CT (3⁄4" to 1 1⁄2"), 438S4, 650S4, 650S4Fasco® HD


in 316*

16 3⁄4" 5000 S16N075P51

16 1" 5000 S16N100P53

16 1 1⁄4" 5000 S16N125P55

304 and 316 Stainless Steel, 1" Crown

COLLATED STAPLES | Similar to Senco® “P” Series

Compatible Pneumatic ToolsHitachi® N3824A (1⁄2" to 1 1⁄2") N5024ASenco® PW (3⁄4" -1 1⁄4") & MW (3⁄4" to 1 1⁄2"), SPS (3⁄4" to 1 1⁄2") & PW2 (1" to 2")


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


52

ROOFING Hand-Drive Screws

Length Diameter ThreadLength


1 1⁄2" .235 Full 20 F14C150T20

1 1⁄2" .235 Full 100 F14C150TIC

2" .235 Full 10 F14C200T10

3" .235 Full 10 F14C300T10

4" .235 37⁄8" 10 F14C400T10

5" .235 37⁄8" 10 F14C500T10

6" .235 37⁄8" 5 F14C600T5

7" .235 37⁄8" 5 F14C700T5

8" .235 37⁄8" 1 F14C800T1

10" .235 37⁄8" 1 F14C1000T1

12" .235 37⁄8" 1 F14C1200T1

410 Stainless Steel

HAND-DRIVE SCREWS | Truss Head, Self-Drilling

• #3 Phillips truss head, tapping screw thread (13 threads per inch), drill point• Hardened martensitic stainless-steel alloy (14% Chrome, 1% Nickel, 1% Molybdenum)• Secure single-ply membrane through insulation to steel purlins• Factory Mutual approved for fastening to 16–22 gauge steel and wood decking

• Fasten aluminum agricultural roofi ng panels to wood joists without pre-drilling• Extra-sharp point for quick penetration of aluminum panels without “point walking” • Twin-lead thread fastens one to three panel thicknesses securely to wood substrate• Panel screws available with and without aluminum/neoprene bonded sealing washers• 5⁄16" Hex drive

HAND-DRIVE SCREWS | Twin Lead, Hex-Washer Head


in 316*

#9 1" 100 S09100HWAC

#9 1" 1000 S09100HWAM

#9 1 1⁄2" 100 S09150HWAC

#9 1 1⁄2" 1000 S09150HWAM

#9 2" 100 S09200HWAC

#9 2" 1000 S09200HWAM

#9 2 1⁄2" 100 S09250HWAC —

#9 2 1⁄2" 1000 S09250HWAM —

#9 3" 100 S09300HWAC —

#9 3" 1000 S09300HWAM —

18-8 and 316 Stainless Steel



C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


53

ROOFING Hand-Drive Screws


#10 1" 100 F10T100PTC

#10 1" 1000 F10T100PTM

#10 1" 4500 F10T100PTB

#10 2" 100 F10T200PTC

#10 2" 1000 F10T200PTM


#10 1" 100 F10T100PSC

#10 1" 1000 F10T100PSM

#10 1" 4500 F10T100PSB

HAND-DRIVE SCREWS | Pancake/Clip, Self-Drilling

410 Stainless Steel

HAND-DRIVE SCREWS | Pancake/Clip, Type A Point

410 Stainless Steel

HAND-DRIVE SCREWS | Gutter Screws

Size ThreadLength


5⁄16" x 7" 3" 12 T31700GS12

316 Stainless Steel

• Low-profi le head• Ideal for securing clips used in standing seam roofi ng• #3 drill point for quick penetration of metal up to 0.142" (118 mils. or 10 ga.) material thickness• #2 Square drive

• Low-profi le head• Ideal for securing clips used in standing seam roofi ng• #2 Square drive

• These longer screws are ideal for fastening rain gutters to wood facia board• Sold in a kit of 12 screws, 12 aluminum ferrules and a hex driver.• 3⁄16" Hex socket drive



C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


54

FRAMING

You can count on Simpson Strong-Tie to deliver the best combination of long lasting quality and service when it comes to stainless-steel fasteners for framing and structural applications.

Hand-Drive Nails Simpson Strong-Tie® Swan Secure nails meet or exceed today’s toughest standards for quality and corrosion resistance. Framing, dock construction, and permanent wood foundations will stand the test of time when our AISI-graded stainless-steel fasteners are used in their construction. Our hand-driven nails are available in ring shank, smooth shank and screw shank.

Collated NailsWe distribute a wide selection of collated nails designed for the pneumatic tools you trust on the job. Choose the appropriate collation to fi t your framing gun – we stock plastic collation, paper tape, and wire weld. Furthermore, we proudly recommend our collated nails expressly developed for metal-connector nailers used for installing joist hangers and other structural connectors. They’re available in both paper tape and plastic collation to fi t all the popular tools.

Timber Tamers™

Another of our recently introduced products is the innovative Timber Tamer™. This fastener is a big improvement over the lag screw in that it requires no pre-drilling thanks to its unique four-corner, torque-reducing thread design.

FRAMING

Hand-Drive NailsCommon Ring Shank, Un-Common™ ..................................................55

Common Smooth Shank, Un-Common™ ............................................55

Post and Beam ....................................................................................56

Box ......................................................................................................56

Structural-Connector .......................................................................... 57

Un-Common™ Common Smooth Shank ............................................. 57

Collated NailsPlastic Strip 20–22°, Full Round, Ring Shank, Stainless ................... 57

Plastic Strip 20–22°, Full Round, Ring Shank, Bronze .......................58

Plastic Strip 20–22°, Full Round, Screw Shank, Stainless .................58

Plastic Strip 20–22°, Full Round, Smooth Shank, Stainless ................59

Plastic Strip 20–22°, Full Round, Casing Head, Ring Shank, Stainless ..59

Wire Weld 28°, Clipped Head, Ring Shank, Stainless .........................59

Wire Coil 15°, Ring Shank ...................................................................60

Paper Tape 31–34°, Structural-Connector ..........................................60

Plastic Strip 31–34°, Full Round, Ring Shank .................................... 61

Paper Tape 31–34°, Clipped Head, Ring Shank .................................. 61

Hand-Drive ScrewsHex-Washer Head, Timber Tamers™ ................................................... 62

Hex-Washer Head, Strong-Drive® .......................................................63

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


55

FRAMING Hand-Drive Nails


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket


2d 1" 15 .072" 3⁄16" 807 S2ACN25 S2ACN5 S2ACN1 S2ACNB

3d 1 1⁄4" 14 .083" 7⁄32" 473 S3ACN25 S3ACN5 S3ACN1 S3ACNB










30d 4 1⁄2" 6 .203" 7⁄16" 22 S30ACN25 S30ACN5 S30ACN1 —


60d 6" 4 .238" 15⁄32" 12 S60ACN25 S60ACN5 S60ACN1 —

70d 7" 4 .238" 15⁄32" 10 S70ACN25 S70ACN5 S70ACN1 —

• General-purpose nails with the heft to penetrate even the toughest seasoned timber• Recommended fi rst choice for construction of permanent wood foundations by

the ANSI/AF&PA Permanent Wood Foundations Design Specifi cations• Specify annular ring threads provide greater pull-out resistance• Also available in screw shank – call for details• Choose type 316 for seaside applications and superior corrosion resistance• Bucket = 25 lbs.

304 and 316 Stainless Steel, Ring Shank

HAND-DRIVE NAILS | Un-Common™ Common Ring Shank and Smooth Shank



DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket


2d 1" 15 .072" 3⁄16" 807 S2CN25 S2CN5 S2CN1 S2CNB

3d 1 1⁄4" 14 .083" 7⁄32" 473 S3CN25 S3CN5 S3CN1 S3CNB

4d 1 1⁄2" 12 .109" 1⁄4" 228 S4CN25 S4CN5 S4CN1 S4CNB

5d 1 3⁄4" 12 .109" 1⁄4" 193 S5CN25 S5CN5 S5CN1 S5CNB

6d 2" 11 .120" 17⁄64" 144 S6CN25 S6CN5 S6CN1 S6CNB

7d 2 1⁄4" 11 .120" 17⁄64" 133 S7CN25 S7CN5 S7CN1 S7CNB

8d 2 1⁄2" 10 .134" 9⁄32" 94 S8CN25 S8CN5 S8CN1 S8CNB

10d 3" 9 .148 5⁄16" 67 S10CN25 S10CN5 S10CN1 S10CNB

12d 3 1⁄4" 9 .148" 5⁄16" 60 S12CN25 S12CN5 S12CN1 S12CNB

16d 3 1⁄2" 8 .165" 11⁄32" 44 S16CN25 S16CN5 S16CN1 S16CNB

20d 4" 6 .203" 7⁄16" 25 S20CN25 S20CN5 S20CN1 —

30d 4 1⁄2" 6 .203" 7⁄16" 22 S30CN25 S30CN5 S30CN1 —

40d 5" 6 .203" 7⁄16" 19 S40CN25 S40CN5 S40CN1 —

60d 6" 4 .238" 15⁄32" 12 S60CN25 S60CN5 S60CN1 —

70d 7" 4 .238" 15⁄32" 10 S70CN25 S70CN5 S70CN1 —

304 and 316 Stainless Steel, Smooth Shank


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


56

FRAMING Hand-Drive Nails


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.


6d 2" 12 .109" 17⁄64" 175 S6APB25 S6APB5 S6APB1

8d 2 1⁄2" 11 .120" 17⁄64" 115 S8APB25 S8APB5 S8APB1

10d 3" 10 .134" 9⁄32" 79 S10APB25 S10APB5 S10APB1

12d 3 1⁄4" 10 .134" 9⁄32" 72 S12APB25 S12APB5 S12APB1

16d 3 1⁄2" 9 .148" 5⁄16" 56 S16APB25 S16APB5 S16APB1

20d 4" 8 .165" 11⁄32" 40 S20APB25 S20APB5 S20APB1

30d 4 1⁄2" 8 .165" 11⁄32" 35 S30APB25 S30APB5 S30APB1

40d 5" 8 .165" 11⁄32" 31 S40APB25 S40APB5 S40APB1

60d 6" 6 .203" 7⁄32" 17 S60APB25 S60APB5 S60APB1

70d 7" 4 .238" 15⁄32" 10 S70APB25 S70APB5 S70APB1

• Slightly lighter gauge than our “Un-Commons,” our Post & Beam nails are easily driven with minimum splitting

• Favored for cooling tower construction, repair and upgrade, these nails are ideal for either fi r or redwood construction

• Use longer lengths for framing jobs using preservative-treated structural members• Annular ring threads offer greater pull-out resistance• Screw shank available – call for details• Also available in silicon bronze – contact Simpson Strong-Tie for details• Choose type 316 for seaside applications and superior corrosion resistance


HAND-DRIVE NAILS | Post and Beam, Ring Shank

*For sizes available in 316 stainless steel( ), substitute the letter “T” as the fi rst character of the item number.


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.


3d 1 1⁄4" 14 .083" 7⁄32" 473 S3ABN25 S3ABN5 S3ABN1

4d 1 1⁄2" 14 .083" 7⁄32" 413 S4ABN25 S4ABN5 S4ABN1

5d 1 3⁄4" 13 .095" 13⁄64" 260 S5ABN25 S5ABN5 S5ABN1

6d 2" 12 .109" 17⁄64" 175 S6ABN25 S6ABN5 S6ABN1

7d 2 1⁄4" 12 .109" 17⁄64" 153 S7ABN25 S7ABN5 S7ABN1

8d 2 1⁄2" 12 .109" 17⁄64" 138 S8ABN25 S8ABN5 S8ABN1

10d 3" 11 .120" 17⁄64" 99 S10ABN25 S10ABN5 S10ABN1

12d 3 1⁄4" 10 .134" 9⁄32" 72 S12ABN25 S12ABN5 S12ABN1

16d 3 1⁄2" 10 .134" 9⁄32" 67 S16ABN25 S16ABN5 S16ABN1

20d 4" 8 .165" 11⁄32" 40 S20ABN25 S20ABN5 S20ABN1

• Slender shank minimizes wood splitting• Checkered fl at head diffracts sunlight and accepts surface fi nishes• Recommended for hardboard siding materials• Annular ring threads offer greater pull-out resistance• Screw shank available – call for details• Choose type 316 for seaside applications and superior corrosion resistance


HAND-DRIVE NAILS | Box, Ring Shank

*For sizes available in 316 stainless steel( ), substitute the letter “T” as the fi rst character of the item number.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


57

FRAMING Hand-Drive Nails / Collated Nails


HeadDiameter


25 lb. Item No.

1 lb. Item No.

8dx1 1⁄2 1 1⁄2" 10 .134" 5⁄16" 147 SSN8D25 SSN8D10dx1 1⁄2 1 1⁄2" 9 .148" 5⁄16" 126 SSN10D25 SSN10D

8d 2 1⁄2" 10 .134" 9⁄32" 94 SS8D25 SS8DD10d 3" 9 .148" 5⁄16" 66 SS10D25 SS10DD16d 3 1⁄2" 8 .165" 11⁄32" 44 SS16D25 SS16DD


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.

4d 1 1⁄2" 10 .134" 5⁄16" 147 S4JHN25 S4JHN5 S4JHN14d 1 1⁄2" 9 .148" 5⁄16" 126 S4HJHN25 S4HJHN5 S4HJHN18d 2 1⁄2" 10 .134" 9⁄32" 94 S8JHN25 S8JHN5 S8JHN110d 3" 9 .148" 5⁄16" 67 S10JHN25 S10JHN5 S10JHN116d 3 1⁄2" 8 .165" 11⁄32" 44 S16JHN25 S16JHN5 S16JHN1

• For installation of joist hangers, structural connectors and hurricane clips in corrosive environments• Annular ring shank structural connector nails also available – call for details

• General-purpose nails with the heft to penetrate even the toughest seasoned timber• Annular ring shank nails also available – see page 55.• Bucket = 25 lbs.

316 Stainless Steel

304 Stainless Steel

HAND-DRIVE NAILS | Structural Connectors, Smooth Shank

HAND-DRIVE NAILS | Un-Common™ Common Smooth Shank

• 20–22° collation angle • 9⁄32" diameter checker-patterned round head• Orange or clear glue on nails to further increase pull-out resistance• Choose type 316 for seaside applications and superior corrosion resistance



in 316*

2" .113" 5000 S12A200CNB2" .113" 1000 S12A200CNJ2" .120" 5000 S11A200CNB2" .120" 1000 S11A200CNJ

2 1⁄4" .148" 1000 S9A225CNJ —2 3⁄8" .113" 5000 S12A237CNB2 3⁄8" .113" 1000 S12A237CNJ2 1⁄2" .120" 4000 S11A250CNB2 1⁄2" .120" 1000 S11A250CNJ2 1⁄2" .134" 4000 S10A250CNB —3" .120" 4000 S11A300CNB3" .120" 1000 S11A300CNJ3" .134" 4000 S10A300CNB3" .134" 1000 S10A300CNJ

3 1⁄4" .120" 4000 S11A325CNB3 1⁄4" .120" 1000 S11A325CNJ3 1⁄4" .134" 4000 S10A325CNB3 1⁄4" .134" 1000 S10A325CNJ3 1⁄2" .134" 4000 S10A350CNB3 1⁄2" .134" 1000 S10A350CNJ




Compatible Pneumatic Tools – Collated 20–22° Plastic Stripsee following page >

These nails also available in Silicon Bronzesee following page >

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


58

FRAMING Collated Nails

• 20–22° collation angle • 9⁄32" diameter checker-patterned round head• Orange or clear glue on nails to further increase pull-out resistance• Choose type 316 for seaside applications and superior corrosion resistance

Compatible Pneumatic Tools – Collated 20–22° Plastic Strip

Bostitch® RN90, RN95HN (up to .162"), N88RH (up to .162"), N88HR-2MCN, F21PLDewalt® D51845, D51844Duo-Fast® CN350, SNP-83, NSP-350FFasco® R5C-RHN20-90SSHitachi® NR83A (up to 3 1⁄4"), NR90AC2 (up to .162"), NR90AC, NR90AA2, NR83AG, NR90SSCMakita® AN8300, AN922MAX® SN890RH, SN90, GS683Paslode® 5350/SRH20Porter Cable® FR350, FR350A, FR350MAGSenco® FramePro 600FRH & FramePro 602 (up to 3 1⁄2"), FramePro 650FRH (2 1⁄4" to 3 1⁄2"),

FramePro 652 (up to 3 1⁄2"), FramePro 700XL FRH, FramePro 702XP (upto 3 1⁄2") & FramePro 752XP (up to 3 1⁄2"), SN60, SN65C (up to .162")

Stan-Tech® SDN11, SDN11B-1

COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Screw Shank



in 316*

2" .113" 5000 S12S200CNB

2" .113" 1000 S12S200CNJ

2 1⁄2" .113" 4000 S12S250CNB

2 1⁄2" .113" 1000 S12S250CNJ

3" .120" 4000 S11S300CNB

3" .120" 1000 S11S300CNJ

3 1⁄4" .120" 4000 S11S325CNB

3 1⁄4" .120" 1000 S11S325CNJ

3 1⁄2" .134" 4000 S10S350CNB

3 1⁄2" .134" 1000 S10S350CNJ



Silicon Bronze


BoxCount Item No.

2 1⁄2" .120" 4000 I11A250CNB

2 1⁄2" .120" 1000 I11A250CNJ

3 1⁄4" .120" 4000 I11A325CNB

3 1⁄4" .120" 1000 I11A325CNJ

• 20–22° collation angle • 9⁄32" diameter checker-patterned round head• Silicon Bronze offers higher resistance to stress corrosion cracking in salt water


Your Nail Gun, Our FastenersTool manufacturers are constantly introducing new tools to the market. If you don’t see your particular model in our tool compatibility listings, visit www.strongtie.com or call any of our locations and a sales professional will assist you in your fastener selection.

!

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


59


• 20–22° collation angle • 1⁄4" diameter checker-patterned, countersunk casing head• Orange or clear glue on nails to

enhance pull-out resistance• Available with painted heads –

see below


BoxCount Item No.

2 3⁄8" .120" 1000 S11A237KDJ

3 1⁄4" .134" 1000 S10A325KDJ

304 Stainless Steel

COLLATED NAILS | Plastic Strip 20–22°, Casing Head, Ring Shank

• 20–22° collation angle • 9⁄32" diameter smooth, full round head• Choose type 316 for seaside applications and superior corrosion resistance

COLLATED NAILS | Plastic Strip 20–22°, Full Round Head, Smooth Shank



in 316

1 1⁄2" .148" 1000 T9N150JNJ **

2 3⁄8" .113" 5000 S12N237CNB —

2 3⁄8" .113" 1000 S12N237CNJ —

2 3⁄8" .148" 1000 S9N237CNJ —

3" .148" 1000 S9N300CNJ —

3 1⁄2" .162" 1000 S8N350CNJ —



• 28° collation angle• Side-by-side wire weld collation

COLLATED NAILS | Wire Weld 28°, Clipped Head, Ring Shank


Bostitch® N16, N80SB and N86S (2" to 3 1⁄2"), N88WW, N100S, N70S and N70SB (2" to 3"), N100S (2" to 4")

Craftsman® 18430Max® SN890CH/28Porter Cable® FM350A


BoxCount Item No.

2 3⁄8" .113" 1000 S12A237W28

3" .120" 1000 S11A300W28

3 1⁄4" .131" 1000 S10A325W28

304 Stainless Steel


Brown Gray Redwood Sienna Tan

1. When ordering in colors, substitute the last three letters in the model number: KJB = Brown, KJG = Gray, KJR = Redwood, KJS = Sienna; KJT = Tan. So a 2 3⁄8" nail in Brown is model S11A237KJB.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


60


Compatible Pneumatic Tools – Collated 31° Paper Tape

Bostitch® F33PT (1 1⁄2" - 2 1⁄2"), MCN150 (1 1⁄2"), MCN250 (2 1⁄2")Hitachi® NR65AKPaslode® 5250, F250S-PP

• 31° collation angle • Side-by-side paper tape collation• 316 stainless steel for superior corrosion resistance


DiameterHeadSize

BoxCount Item No.

4d Heavy 1 1⁄2" .148" 9⁄32" 1500 T9A150MCN

8d Heavy 2 1⁄2" .148" 9⁄32" 1000 T9A250MCN

316 Stainless Steel

COLLATED NAILS | Paper Tape 31°, Structural Connector, Ring Shank

• 15° collation angle• Choose type 316 for seaside applications and superior corrosion resistance



DiameterHeadSize


in 316*

4d 1 1⁄2" .099" 1⁄4" 3600 S12A150PNB —

5d 1 3⁄4" .099" 1⁄4" 3600 S12A175PNB —

6d 2" .099" 1⁄4" 3600 S12A200PNB —

7d 2 1⁄4" .099" 1⁄4" 1800 T12A225PNJ **

8d 2 1⁄2" .099" 1⁄4" 3600 S12A250PNB

8d 2 3⁄8" .113" 1⁄4" 3600 S12A237PNB —

10d 3" .120" 17⁄64" 1800 S11A300PNJ

10d 3" .131" 17⁄64" 1800 S10A300PNJ

12d 3 1⁄4" .120" 17⁄64" 1800 S11A325PNJ

12d 3 1⁄4" .131" 17⁄64" 1800 S10A325PNJ

16d 3 1⁄2" .131" 17⁄64" 1800 T10A350PNJ **




Bostitch® Bostitch N80CB, N86C & N100C, N100CPP, N130C-2Fasco® F5C CN15W75 (up to 3") & CN15W90 (up to 3 1⁄4")Hitachi® NV65AB & NV65AC (up to 2 1⁄2"), NV83A (up to 3 1⁄4"), NV75AG (.099" to .131", 1 3⁄4" to 3")Makita® AN621(1 3⁄4" - 2 1⁄2"), AN901 (1 3⁄4" - 3 1⁄2")MAX® CN80, CN70 (1 3⁄4" to 2 3⁄4"), HN75, HN90, 80F, CN100 (2 1⁄2" to 4"), CN565S (1 3⁄4" to 2 1⁄2"), CN890II,

CN565 (1 1⁄2" to 2 1⁄2"), CN890S, CN665 (1 1⁄2" to 2 1⁄2"), CN565D (1 3⁄4" to 2 1⁄2"), CN565S (1 3⁄4" to 2 1⁄2")Paslode® F325C, P350C (1 1⁄2" to 3 1⁄4"), F275C, P275C (1 1⁄2" to 2 3⁄4"), 4275/CN70 (2" to 2 1⁄2"), 5325/CN80 & 5350C, 5300C (up to 3") Porter Cable® Coil 350 (up to 3 1⁄2") , Coil 250 (up to 2 1⁄2")Senco® SCN56 (up to 2 1⁄2") SCN60 (2" to 2 1⁄2") SCN65 (2" to 3 1⁄2") & SCN300 (1 3⁄4" to 3")Spotnails® MCW64 (up to 2 1⁄2"), YCN83 (up to 3 1⁄4")

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


61


COLLATED NAILS | Paper Tape 31–34°, Clipped Head, Ring Shank



in 316*

2" .113" 1000 S12A200T31

2 3⁄8" .113" 1000 S12A237T31

3" .120" 1000 S11A300T31

3 1⁄4" .131" 1000 S10A325T31

3 1⁄2" .131" 1000 S10A350T31

• 31–34° collation angle• Choose type 316 for seaside applications and superior corrosion resistance

304 Stainless Steel

Compatible Pneumatic Tools – Collated 31–34° Paper Tape

Bostitch® F33PT, N90PT (2" -3 1⁄2")DeWalt® D51823, D51822Duofast® NSPM-325F & CN-325BHitachi® NR83AA & NR83AA2, NR90AAMakita® AN942MAX® SN890CH/34, GS683CHPaslode® F350S Powermaster Plus, Impulse 325 & 350, 5325S, 5300 Plus & 5350S,

F250S-PP, IMCT (2" to 3 1⁄4")Porter Cable® FC350, FC350ASenco® SN4, SN70, FramePro 600 & FramePro 650, SN325+, FramePro 601 (up to 3 1⁄2") &

FramePro 701XP (up to 3 1⁄2"), FramePro 651 (up to 3 1⁄2"), FramePro 750XL (up to 3 1⁄2") & FramePro 751XP (up to 3 1⁄2")

Spotnails® YTD90


• 31–34° collation angle • 9⁄32" diameter checker-patterned round head• Choose type 316 for seaside applications and superior corrosion resistance




in 316*

2 3⁄8" .113" 4000 S12A237B31

2 3⁄8" .113" 1000 S12A237P31

3" .120" 4000 S11A300B31

3" .120" 1000 S11A300P31

3 1⁄4" .131" 4000 S10A325B31

3 1⁄4" .131" 1000 S10A325P31



C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


62

FRAMING Hand-Drive Screws

• For superior corrosion resistance in a range of applications including timber framing, pole barn construction, log homes, gutter installation and landscape timbers

• Available in screw sizes 1⁄4" and 3⁄8" and lengths from 3 to 12 inches • 4-corner thread form signifi cantly reduces driving torque• Drive with standard 5⁄16" or 1⁄2" hex nut drivers• Specify Timber Tamers™ for outdoor construction projects requiring longer length screws

HAND-DRIVE SCREWS | Timber Tamers™, Hex Washer Head

316 Stainless Steel

Size Hex Drive

ThreadLength

Carton Count

Package Count

CartonItem No.

PackageItem No.

1⁄4" x 1 1⁄2" 5⁄16" 1" 100 — T14150TTB —

1⁄4" x 2" 5⁄16" 1 1⁄4" 100 — T14200TTB —

1⁄4" x 2 1⁄2" 5⁄16" 1 1⁄2" 100 — T14250TTB —

1⁄4" x 3" 5⁄16" 2 1⁄4" 100 20 T14300TTB T14300TP

1⁄4" x 3 1⁄2" 5⁄16" 2 1⁄4" 100 — T14350TTB —

1⁄4" x 4" 5⁄16" 2 1⁄4" 100 20 T14400TTB T14400TP

1⁄4" x 4 1⁄2" 5⁄16" 2 1⁄4" 100 — T14450TTB —

1⁄4" x 5" 5⁄16" 2 1⁄4" 100 10 T14500TTB T14500TP

1⁄4" x 6" 5⁄16" 2 1⁄4" 100 10 T14600TTB T14600TP

1⁄4" x 8" 5⁄16" 2 1⁄4" 50 10 T14800TTB T14800TP

3⁄8" x 3" 1⁄2" 3" 100 10 T37300TTB T37300TP

3⁄8" x 4" 1⁄2" 3" 100 10 T37400TTB T37400TP

3⁄8" x 5" 1⁄2" 3" 50 10 T37500TTB T37500TP

3⁄8" x 6" 1⁄2" 3" 50 10 T37600TTB T37600TP

3⁄8" x 8" 1⁄2" 3" 25 10 T37800TTB T37800TP

3⁄8" x 10" 1⁄2" 3" 25 10 T371000TTB T371000TP

3⁄8" x 12" 1⁄2" 3" 25 — T371200TTB —

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


63

FRAMING Hand-Drive Screws

• Designed for installation in Simpson Strong-Tie® structural connectors as well as wood-to-wood applications

• Type-17 tip for fast starts, no predrilling required in most applications• Patented 4CUT™ 4-corner thread form greatly reduces driving torque• Double-barrier coating provides corrosion resistance equivalent to hot-dip galvanization• Head is stamped with the Simpson Strong-Tie “No Equal” sign and fastener length

for easy identifi cation after installation• A low-speed 1⁄2" drill with a 3⁄8" hex driver is the recommended tool for installation • Code listed under ICC-ES ESR-2236

HAND-DRIVE SCREWS | Strong-Drive® Screw, Hex Washer Head

Heat-Treated Carbon Steel

Size Hex Drive

ThreadLength

Retail PackCount

Retail Pack Item No.

Mini BulkCount

Mini BulkItem No.

Bulk PackCount

Bulk PackItem No.

1⁄4" x 1 1⁄4" 3⁄8" 1" 25 SDS25112-R25 300 SDS25112MB 1500 SDS251121⁄4" x 2" 3⁄8" 1 1⁄4" 25 SDS25200-R25 250 SDS25200MB 1300 SDS25200

1⁄4" x 2 1⁄2" 3⁄8" 1 1⁄2" 25 SDS25212-R25 200 SDS25212MB 1100 SDS252121⁄4" x 3" 3⁄8" 2" 25 SDS25300-R25 150 SDS25300MB 950 SDS25300

1⁄4" x 31⁄2" 3⁄8" 2 1⁄4" 10 SDS25312-R10 125 SDS25312MB 900 SDS253121⁄4" x 41⁄2" 3⁄8" 2 3⁄4" 10 SDS25412-R10 100 SDS25412MB 800 SDS25412

1⁄4" x 6" 3⁄8" 3 1⁄4" 10 SDS25600-R10 100 SDS25600MB 600 SDS256001⁄4" x 8" 3⁄8" 3 1⁄4" — SDS25800-R10 — SDS25800MB 400 SDS25800

1. Allowable loads for SDS screws are based on ICC-ES Code Report ESR-2236. Screws may be provided with the 4CUT™ or Type 17 tip.2. Wood to wood applications are based on a wood thickness of 1 1⁄2" side member. All applications are based on full penetration into the main member.

Refer to technical bulletin T-SDSCREWAPPS for allowable loads for other side member thicknesses.3. Allowable loads are shown at the wood load duration factor of CD=1.00. Loads may be increased for load duration by the building code up to a CD=1.60.4. Withdrawal loads shown are in pounds (lbs.) and are based on the entire threaded section installed into the main member.

If thread penetration into the main member is less than the Thread Length as shown in the table, reduce allowable load by 172 lbs. x inches of thread not in main member. Use 121 lbs./inch for SPF.

5. LSL wood-to-wood applications that require 4 1⁄2" and 6" SDS screws are limited to interior-dry use only.6. See www.strongtie.com for important information and general notes for load-rated fasteners.

SDS Screw Load Capacities

Size (in.)

DF/SP Allowable Loads3 SPF/HF Allowable Loads3

Shear (100)1Withdrawal4

(100)Shear (100) Withdrawal4

(100)Wood Side Plate2 Steel Side Plate Wood Side Plate2 Steel Side Plate

1 1⁄2" 1 3⁄4" SCL 16 ga 14 ga &

12 ga10 ga or Greater

Wood or Steel Side Plate 1 1⁄2" 1 3⁄4"

SPF LVL 16 ga 14 ga & 12 ga

10 ga or Greater

Wood or Steel Side Plate

5⁄32 x 1 1⁄4 — — 50 50 50 — — — 45 45 45 —1⁄4 x 1 1⁄2 — — 250 250 250 170 — — 180 180 180 120

1⁄4 x 2 — — — 290 290 215 — — — 210 210 1501⁄4 x 2 1⁄2 190 — — 390 420 255 135 — — 280 300 180

1⁄4 x 3 280 — — 420 420 345 200 — — 300 300 2401⁄4 x 3 1⁄2 340 340 — 420 420 385 245 245 — 300 300 2701⁄4 x 4 1⁄2 350 340 — 420 420 475 250 245 — 300 300 330

1⁄4 x 6 350 340 — 420 420 560 250 245 — 300 300 3951⁄4 x 8 350 340 — 420 420 560 250 245 — 300 300 395

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


64

FINISHING, MILLWORK & TRIM

Fine WoodworkingWhen working with elaborate wood millings, trust Simpson Strong-Tie to match the quality of your materials with fasteners of equal distinction. In addition to hand-driven fi nishing nails, brads and escutcheon pins, we carry a large selection of stainless-steel collated fi nishing nails, brads and staples engineered for today’s most popular pneumatic tools.

PVC TrimCellular PVC trim is a great alternative for traditional wood millwork – it won’t warp, cup, or rot, and it’s generally warranted for 10 years or more. Simpson Strong-Tie offers a variety of corrosion-resistant Swan Secure fasteners designed to last the life of the warranty and beyond. Our Swaneze™ #7 x 2 1⁄4 white painted trim screw is one of our most popular options, followed by our white painted coil siding nails.

FINISHING, MILLWORK & TRIM

Hand-Drive NailsFinishing .....................................................................................65

Collated NailsBostitch®-Type Angle Collated Finishing ...................................66Senco®-Type Angle Collated Finishing ......................................66Paslode®-Type Angle Collated Finishing ...................................66Paslode®-Type Straight Collated Finishing ................................67Straight 18-Gauge Collated Brads .............................................67Wire Coil, Painted Siding ...........................................................68

Hand-Drive ScrewsTrim Head, Square Drive, Swaneze™ ..........................................69Trim Head, 6-Lobe, Woodpecker™ ..............................................69

Hand-Drive Screws, Painted HeadsTrim Head, Square Drive, Swaneze™ ..........................................70

Collated StaplesSimilar To:Bostitch® “BCS” Series .............................................................. 71Senco® “L” Series ....................................................................... 71Paslode® “GS” Series ................................................................. 71Senco® “N” Series ......................................................................72Senco® “P” Series ......................................................................72Senco® “C” Series ......................................................................72

Beautiful millwork and trim accentuate premium construction, and Simpson Strong-Tie offers a wide range of high-grade stainless-steel Swan Secure fasteners expressly designed and engineered for these demanding applications where only the best materials and workmanship will do.

Fine Woodworking

PVC Trim

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


65

FINISHING, MILLWORK & TRIM Hand-Drive Nails


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket


2d 1" 15 .072" .109" 863 S2FN25 S2FN5 S2FN1 S2FNB

3d 1 1⁄4" 15 .072" .109" 649 S3FN25 S3FN5 S3FN1 S3FNB

4d 1 1⁄2" 14 .083" .120" 434 S4FN25 S4FN5 S4FN1 S4FNB

5d 1 3⁄4" 14 .083" .120" 375 S5FN25 S5FN5 S5FN1 S5FNB

6d 2" 13 .095" .135" 247 S6FN25 S6FN5 S6FN1 S6FNB

8d 2 1⁄2" 12 .109" .148" 146 S8FN25 S8FN5 S8FN1 S8FNB

10d 3" 11 .120" .165" 102 S10FN25 S10FN5 S10FN1 S10FNB

12d 3 1⁄4" 11 .120" .165" 97 S12FN25 S12FN5 S12FN1 S12FNB

16d 3 1⁄2" 11 .120" .165" 86 S16FN25 S16FN5 S16FN1 S16FNB

20d 4" 11 .120" .201" 85 S20FN25 S20FN5 S20FN1 S20FNB

• Brad head, smooth shank, diamond point• Choose type 316 for seaside applications and superior

corrosion resistance• Bucket = 25 lbs.


HAND-DRIVE NAILS | Finishing Nails


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


66

FINISHING, MILLWORK & TRIM Collated Nails

COLLATED NAILS | Bostitch®-Type Angle Finishing

Length Box Count Item No. Availablein 316*

1 1⁄2" 3500 S15N150FNJ

2" 3500 S15N200FNJ

2 1⁄2" 3500 S15N250FNJ


304 and 316 Stainless Steel – 15 Gauge


Compatible Pneumatic ToolsBostitch® N60FN, N62FN Makita® AF632Stan-Tech® SDN15BR


1 1⁄4" 4000 T15N125SFN **1 1⁄2" 4000 S15N150SFN

2" 4000 S15N200SFN

2 1⁄2" 4000 S15N250SFN



Compatible Pneumatic ToolsAccuset® A250FN Craftsman® 18442DeWalt® D51275KDuofast® DAFN-6480 Hitachi® NT65AA & NT65MA &NT65MA2MAX® NF550/15-65Porter Cable® DA250A & CDA250 Senco® AirFree 41, FinishPro 35, FinishPro 41XP, SFN40 & SFN1+ (up to 2"), SFN30 (1 1⁄4" to 2")


1 1⁄4" 2000 S16N125PFN

1 1⁄2" 2000 S16N150PFN

2" 2000 S16N200PFN

2 1⁄2" 2000 S16N250PFN



Compatible Pneumatic ToolsDeWalt® DC614KA, DC618KAPaslode® IM250A

COLLATED NAILS | Senco®-Type Angle Finishing

COLLATED NAILS | Paslode®-Type Angle Finishing

CAUTION!All of our collated fi nishing nails and brads are held together with a Mylar tape collation medium. Although Mylar tape is fl exible and durable, care should be taken when storing these products between jobs. High heat, humidity, and moisture can contribute to the premature degradation of the tape’s adherence which will cause the fastener strips to fall free from the collation which is not covered by any warranty. Please remember to keep collated fasteners of this variety away from adverse conditions.

!

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


67


COLLATED NAILS | Paslode®-Type 16 Gauge Straight Finishing


1 1⁄4" 2500 T16N125FNJ **1 1⁄2" 2500 S16N150FNJ

2" 2500 S16N200FNJ

2 1⁄2" 2500 S16N250FNJ



Compatible Pneumatic ToolsAccuset® A250SM Bostitch® SB-1664FN, FN16250DeWalt® D51256KDuofast® LFN-764A Hitachi® NT65A, NT65A2Max® NF352-ST/16-50 (1" to 2")Paslode® IM250F, IM250II, MU-112B & MU-212-F, 3250-F16 & 3200-F16 (up to 2"),

T250-F16, 3250-F14 (3⁄4" to 2 1⁄2") Porter Cable® CFN250, FN250, FN250A & FN200 (up to 2")Senco® FinishPro 32


COLLATED NAILS | Straight Brads


1⁄2" 5000 T18N050FNJ **5⁄8" 5000 T18N062FNJ **3⁄4" 5000 S18N075FNJ

1" 5000 T18N100FNJ **1 1⁄4" 5000 S18N125FNJ

1 1⁄2" 5000 S18N150FNJ

1 3⁄4" 5000 S18N175FNJ

2" 5000 S18N200FNJ



Compatible Pneumatic ToolsBostitch® BT50B (1 3⁄16" to 2"), T31-1B (5⁄8" to 1") & T29-30 (5⁄8" to 1 3⁄16"), SB-1842BN &

2IN1 (5⁄8" -1 5⁄8"), SB-1850BN & BT200 (5⁄8" -2"), BT125 (5⁄8" -1 1⁄4")DeWalt® D51238K (5⁄8" -2")Hitachi® NT45A (1" to 1 3⁄4"), NT50AD (1" to 2"), NT32AE (5⁄8" to 1 1⁄4"), NT50AE (3⁄4" to 2"),

Bostitch BT35B (5⁄8" to 1 3⁄8") Max® NF201/18-35 (3⁄8" to 1 1⁄4"), NF221/18-55 (5⁄8" to 2")Paslode® 2138-F18II & IM200-F18, T200-F18 (5⁄8" to 2"), T125-F18 (5⁄8" to 1 1⁄4")Porter Cable® BN125 (5⁄8" to 1 1⁄4") & BN200 (3⁄4" to 2") Senco® FinishPro 15 (5⁄8" to 1 1⁄4"), FinishPro 18 (5⁄8" to 2"), FinishPro 25,

FinishPro 25XP (5⁄8" to 2"), FinishPro 2N1 (5⁄8" to 1 1⁄4"), AirFree 25 (5⁄8"-2 1⁄8"), SLP20 (up to 1 1⁄2"), LS4 & LS5 (up to 1 5⁄8")


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


68


• Protect your investment in fi ne wood siding from hard-to-remove stains and streaks • Absolutely the highest quality nails for cedar, redwood and cypress siding materials• Stainless steel will last the life of wood siding without degrading in most environments• Slender gauge and blunt diamond point minimize splitting• Generous under-head fi llet allows nails to be driven fl ush, or countersunk, without

crushing surrounding wood • Checker-patterned head blends with wood texture and serves to diffract sunlight• Annular ring threads reduce cupping of siding boards and nail-head popping


HeadDiameter Color Box

Count Item No.

2" .090" 13⁄64" Dark Brown 3600 S13A200CCB

2" .090" 13⁄64" Gray 3600 S13A200CCG

2" .090" 13⁄64" Redwood 3600 S13A200CCR

2" .090" 13⁄64" Cedar 3600 S13A200CCT

2" .090" 13⁄64" White 3600 S13A200CWH

2 3⁄16" .090" 13⁄64" Dark Brown 3600 S13A219SNB

2 3⁄16" .090" 13⁄64" White 3600 S13A219SNC

2 3⁄16" .090" 13⁄64" Gray 3600 S13A219SNG

2 3⁄16" .090" 13⁄64" Redwood 3600 S13A219SNR

2 3⁄16" .090" 13⁄64" Cedar 3600 S13A219SNT

2 1⁄2" .090" 13⁄64" Dark Brown 3600 S13A250CCB

2 1⁄2" .090" 13⁄64" Gray 3600 S13A250CCG

2 1⁄2" .090" 13⁄64" Redwood 3600 S13A250CCR

2 1⁄2" .090" 13⁄64" Cedar 3600 S13A250CCT

2 1⁄2" .090" 13⁄64" White 3600 S13A250CWH

COLLATED NAILS | Wire Coil, Painted Siding

Compatible Pneumatic Tools Bostitch® N63CP, N64C, N65CP, N66CHitachi® NV65AH, NV65ACMAX® CN565, CN565S, CN70 (1 3⁄4" to 2 3⁄4"), CN55 (1" to 2 1⁄4")Paslode® 3225/CN55Senco® SCN55S

304 Stainless Steel

Our collated painted siding nails incorporate a slender shank and a small head making them perfect for many fi nishing and millwork projects.

Both 1 1⁄2" and 1 3⁄4" lengths are also available painted should the requirement arise. Just call any of our sales professionals for pricing and lead time.

Custom colors are available on any of our painted siding nails provided that we have a color swatch with which we can match your color – please call for details.

!

Dark Brown Gray Redwood Cedar White

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


69

FINISHING, MILLWORK & TRIM Hand-Drive Screws


Carton/BucketCount

5 lb.Item No.

1 lb. Item No.


Bucket Item No.

Deck PackItem No.

Availablein 316*

#7 1" 316 5000 S07100FB5 S07100FB1 S07100FBC S07100FBB S07C100PAK —

#7 1 1⁄4" 256 5000 S07125FB5 S07125FB1 S07125FBC S07125FBB S07C125PAK —

#7 1 5⁄8" 195 4000 S07162FB5 S07162FB1 S07162FBC S07162FBB S07C162PAK




#7 3" 98 2000 S07300FB5 S07300FB1 S07300FBC S07300FBB S07C300PAK


#9 4" 61 1000 S09400FB5 S09400FB1 S09400FBC S09400FBB — —


• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw the workpiece

tightly to the substrate• Pre-drilling always recommended, and a must near board ends to prevent splitting• Use with stable woods and wood substitutes when screw heads need to be hidden• Deck Packs contain 350 screws, enough to fasten 100 sq. ft.

(6" nominal boards on 16" centers)• #7 screw has 0.230" head diameter and #1 square drive recess• #9 x 3½" screw has 0.250" head diameter and #1 square drive recess• #9 x4" screw has 0.250" head diameter and #2 square drive recess• Choose type 316 for seaside applications and superior corrosion resistance



• Proprietary thread form greatly reduces torque and allows these screws to drive into tropical hardwoods, often without pre-drilling

• 0.230" casing-style head and slender #7 diameter for fi nish work and trim• 6-lobe drive prevents driver bit cam-out and stripping in recess• Made of solid 316 stainless steel for superior corrosion resistance• Threaded approximately 2⁄3 up the shank to tightly draw the workpiece to the substrate• Pre-drilling not always necessary, except near board ends to prevent splitting• 6-lobe driver bit included in both Bulk Cartons and Deck Packs

HAND-DRIVE SCREWS | Woodpeckers™ Trim Head, 6-Lobe Drive


6-LobeDrive

CartonCount


Deck PackCount

Deck PackItem No.

#7 1 5⁄8" 0.230" T-15 4000 T07162WPB 350 T07162WPP

#7 2 1⁄4" 0.230" T-15 1750 T07225WPB 350 T07225WPP

#7 3" 0.230" T-15 1750 T07300WPB 350 T07300WPP

316 Stainless Steel

Deck Packs contain enough screws to fasten up to 100 sq. ft. (6" nominal boards on 16" centers).Bulk Cartons contain enough screws to fasten up to 500 sq. ft. (6" nominal boards on 16" centers).

!

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


70

FINISHING, MILLWORK & TRIM Hand-Drive Screws – Painted Head

• Durable, powder-coated fi nish – painted heads blend with fi nish work• 0.230" diameter #1 square drive, trim head• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw the workpiece tightly to the substrate• Slender #7 shank for fi nish work and trim• Pre-drilling recommended near board ends to prevent splitting• Use with stable woods and wood substitutes when screw heads need to be hidden• Choose type 316 for seaside applications

and superior corrosion resistance

HAND-DRIVE SCREWS | Swaneze™ Painted Trim Head, Square Drive



Deck PackCount

Deck PackItem No.

Availablein 316*

#7 1 5⁄8" Gray 1750 T07162FCG 350 T07162FJG **#7 1 5⁄8" Ipê 1750 S07162FCI 350 S07162FJI

#7 1 5⁄8" Tan 1750 T07162FCT 350 T07162FJT **#7 1 5⁄8" White 1750 T07162FCW 350 S07162FJW

#7 2 1⁄4" Almond 1750 S07225FCA 350 S07225FJA —

#7 2 1⁄4" Black 1750 S07225FCBB 350 S07225FJB —

#7 2 1⁄4" Gray 1750 S07225FCG 350 S07225FJG

#7 2 1⁄4" Ipê 1750 S07225FCI 350 S07225FJI

#7 2 1⁄4" Khaki 1750 S07225FBK 350 S07225FJK —

#7 2 1⁄4" Tan 1750 S07225FCT 350 S07225FJT

#7 2 1⁄4" White 1750 S07225FCW 350 S07225FJW

#7 2 1⁄4" Azek Gray 1750 S07225FCZ 350 S07225FZJ —

#7 2 1⁄4" Mocha 1750 S07225FJM 350 S07225FCM —

#7 3" Gray 1750 S07300FCG 350 S07300FJG —

#7 3" Ipê 1750 S07300FCI 350 S07300FJI —

#7 3" Tan 1750 S07300FCT 350 S07300FJT —



Tan Gray Almond Ipê Black White KhakiAzek Gray

Mocha

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


71

FINISHING, MILLWORK & TRIM Collated Staples



Compatible Pneumatic ToolsFasco® GSPaslode® IM200-S16, 4200-S16 & 3200-S16P, 3150-S16 (3⁄4" to 1 1⁄2")



16 1 1⁄4" 10,000 T16N125B07

16 1 1⁄2" 10,000 T16N150B09

16 1 3⁄4" 10,000 T16N175B11

16 2" 10,000 T16N200B13



Compatible Pneumatic ToolsBostitch® T36-1, T36-50, T50S4-1 & T55S4-1 (3⁄4" to 1 3⁄4") 438S2R (1⁄2" -1 1⁄2"),

T40S4-CT (3⁄4" to 1 1⁄2") , 438S4, 650S4Fasco® HD


in 316*

18 5⁄8" 5000 S18N062L10

18 3⁄4" 5000 T18N075L11 **

18 1" 5000 S18N100L13

18 1 1⁄8" 5000 S18N112L14

18 1 1⁄4" 5000 S18N125L15

18 1 1⁄2" 5000 S18N150L17


COLLATED STAPLES | Similar to Senco® “L” Series

Compatible Pneumatic Tools Duo-Fast® KN-1848AGrizzly® G6043Haubold® PN6040HHilti® SN-114B, SN-118Hitachi® N3804A, N3804AA & N3804ABPorter Cable® NS100 (1⁄2" to 1") NS150 (1⁄2" -1 1⁄2")Senco® FinishPro 2N1 (1⁄4" -1"), SLS15 (5⁄8" to 1"), SLS18 (1⁄2" -1 1⁄2"), SLS20,

SLS25XP (3⁄8" to 1 1⁄2"), SKSL12-17 (7⁄8" to 1 1⁄2"), SKSL11-15 (3⁄4" to 1 1⁄4")



in 316*

16 1 1⁄4" 10,000 S16N125GS

16 1 1⁄2" 10,000 S16N150GS

16 1 3⁄4" 10,000 S16N175GS

16 2" 10,000 S16N200GS —

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


72

FINISHING, MILLWORK & TRIM Collated Staples


in 316*

16 3⁄4" 5000 T16N075N11 **

16 1" 5000 S16N100N13

16 1 1⁄4" 5000 S16N125N15

16 1 1⁄2" 5000 S16N150N17

16 1 3⁄4" 5000 S16N175N19

16 2" 5000 S16N200N21



Compatible Pneumatic Tools Bostitch® 650S5Hitachi® N5008AA & A1, N5008AB & N5008ACFasco® GMax® TA551/16-11 (1" to 2")Porter Cable® CMS200 & MS200Senco® M1 (3⁄4" -1 1⁄4"), SNS45 (1" -2"), SNS50 (1 1⁄4" -2"), SKS (3⁄4" to 1 1⁄2"), M2+ (1 1⁄4" to 2"), SNS45 (1" to 2")



in 316

16 3⁄4" 5000 S16N075P51

16 1" 5000 S16N100P53

16 1 1⁄4" 5000 S16N125P55

304 and 316 Stainless Steel, 1" Crown

Compatible Pneumatic Tools Hitachi® N3824A (1⁄2" -1 1⁄2") N5024ASenco® PW (3⁄4" to 1 1⁄4") & MW (3⁄4" to 1 1⁄2"), SPS (3⁄4" to 1 1⁄2") & PW2 (1" to 2")



22 1⁄4" 10,000 S22N025C04

22 3⁄8" 10,000 S22N037C06

22 1⁄2" 10,000 S22N050C08


COLLATED STAPLES | Similar to Senco “C” Series

COLLATED STAPLES | Similar to Senco “P” Series

Compatible Pneumatic Tools BeA® 71/16-421Porter Cable® US58Senco® SJ10 A/D, SFW10XP

• Great for marine upholstery

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


73

COMPOSITES & FIBERGLASS

Composite LumberComposite lumber is taking the nation by storm with the notion of a “maintenance-free deck.” Our premium, stainless-steel fasteners go a long way toward ensuring both the structural integrity and corrosion-free appearance of decks built with composite materials. One of our most recent product innovations, Dexxter™ reduces bothersome “mushrooming” thanks to a revolutionary thread design. What’s more, Dexxter requires no pre-drilling and comes in a range of composite-matching head colors. Due to the many composite types available it is diffi cult to predict fi nal appearance, so always test-drive fasteners to confi rm acceptability.

FiberglassWhether you’re installing fi berglass panels or making repairs to a fi berglass boat, you’ll appreciate our AISI type 316 stainless-steel Sharx™ for their quick bite, extreme holding power and exceptional corrosion resistance. Sharx are available with pan, fl at or oval heads – all with Phillips drive – and up to #14 screw diameter.

COMPOSITES & FIBERGLASS

Hand-Drive ScrewsComposite Decking, 6-Lobe Drive, Dexxter™ ....................................74Marine, Flat Head, Sharx™ ..................................................................74Marine, Pan Head, Sharx™ ................................................................ 75Marine, Oval Head, Sharx™ ............................................................... 75Truss Head, Coarse Thread, Square Drive ........................................ 76Trim Head, Square Drive, Swaneze™ ................................................. 76Trim Head, Square Drive, Swaneze™ with Sealing Washers .................77

Hand-Drive NailsCommon Ring Shank, Un-Common™ .................................................77

With a growing trend toward “green” building materials, composites and fi berglass are becoming increasingly popular as wood substitutes, primarily because of their demonstrated durability and reduced maintenance requirements. Our equally durable, corrosion-resistant fasteners will virtually eliminate the likelihood of unsightly staining of your building project for years to come. Insist on proven Simpson Strong-Tie® Swan Secure AISI-graded stainless-steel fasteners in all of your wood-substitute applications.

Composite Decking

Fiberglass Panels

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


74

COMPOSITES & FIBERGLASS Hand-Drive Screws

Size Length Head Diameter

6-Lobe Drive

Contractor Pack Count


Deck Pack Count

Deck Pack Item No.

Available in 316

#10 1 1⁄2" 0.265" T-20 1750 S10150DXB 350 S10150DXP —

#10 2" 0.265" T-20 1750 S10200DXB 350 S10200DXP —

#10 2 1⁄2" 0.265" T-20 1750 S10250DXB 350 S10250DXP

#10 3" 0.265" T-20 1750 S10300DXB 350 S10300DXP —

• Unique thread form removes exhaust while driving to reduce “mushrooming” in composite decking

• Type-17 point for fast starts• 6-lobe drive prevents driver bit cam-out and stripping in recess• Small head diameter is less visible• Pre-drilling recommended near board ends to prevent splitting• Painted heads available• Patent pending• Six-lobe driver included in both Contractor Packs and Deck Packs• Choose type 316 for seaside applications and superior corrosion resistance

HAND-DRIVE SCREWS | Dexxter™, Composite Decking, 6-Lobe Drive




NominalScrew Diameter

100-CountItem No.

1000-CountItem No.

#6 1⁄2" .244/.279 .138 T06J050FXC T06J050FXM

#6 3⁄4" .244/.279 .138 T06J075FXC T06J075FXM

#8 3⁄4" .292/.332 .164 T08J075FXC T08J075FXM

#6 1" .244/.279 .138 T06J100FXC T06J100FXM

#8 1" .292/.332 .164 T08J100FXC T08J100FXM

#10 1" .340/.385 .190 T10J100FXC T10J100FXM

#8 1 1⁄4" .292/.332 .164 T08J125FXC T08J125FXM

#10 1 1⁄4" .340/.385 .190 T10J125FXC T10J125FXM

#8 1 1⁄2" .292/.332 .164 T08J150FXC T08J150FXM

#10 1 1⁄2" .340/.385 .190 T10J150FXC T10J150FXM

#10 2" .340/.385 .190 T10J200FXC T10J200FXM

• Sharx™ screws bite and hold fast in fi berglass, plywood and wood substitute materials• Use for projects exposed to harsh marine or many chemically caustic conditions• Ideal for applying trim, rub rail and molding to fi berglass boat hulls• Extra-sharp points speed screw starts during assembly• Specially engineered, high/low thread form incorporates indentations (“teeth”) that

cut easily and quickly through high-density materials• Back-out resistance: once driven home, Sharx are locked in place thanks to their “teeth”

(the thread indentations will resist back-out even after prolonged vibration)• Holding power: Pull-out values of Sharx screws exceed those of ordinary

tapping screws in fi berglass and wood• Screws up to 1" in length are fully threaded.

Screws more than 1" long are threaded 2⁄3 of the shank length• Phillips drive

HAND-DRIVE SCREWS | Sharx™ Marine Screws

316 Stainless Steel, Flat Head

continued on following page >

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


75




100-CountItem No.

1000-CountItem No.

#6 3⁄4" .244/.279 .138 T06J075OXC T06J075OXM

#8 3⁄4" .292/.332 .164 T08J075OXC T08J075OXM

#10 3⁄4" .340/.385 .190 T10J075OXC T10J075OXM

#6 1" .244/.279 .138 T06J100OXC T06J100OXM

#8 1" .292/.332 .164 T08J100OXC T08J100OXM

#10 1" .340/.385 .190 T10J100OXC T10J100OXM

#12 1" .380/.412 .216 T12J100OXC T12J100OXM

#14 1" .427/.462 .242 T14J100OXC T14J100OXM

#8 1 1⁄4" .292/.332 .164 T08J125OXC T08J125OXM

#10 1 1⁄4" .340/.385 .190 T10J125OXC T10J125OXM

#8 1 1⁄2" .292/.332 .164 T08J150OXC T08J150OXM

#10 1 1⁄2" .340/.385 .190 T10J150OXC T10J150OXM

#12 1 1⁄2" .380/.412 .216 T12J150OXC T12J150OXM

#14 1 1⁄2" .427/.462 .242 T14J150OXC T14J150OXM

#12 2" .380/.412 .216 T12J200OXC T12J200OXM

#14 2" .427/.462 .242 T14J200OXC T14J200OXM

316 Stainless Steel, Oval Head



100-CountItem No.

1000-CountItem No.

#6 1⁄2" .256/.270 .138 T06J050PXC T06J050PXM

#8 1⁄2" .306/.322 .164 T08J050PXC T08J050PXM

#10 1⁄2" .357/.373 .190 T10J050PXC T10J050PXM

#6 3⁄4" .256/.270 .138 T06J075PXC T06J075PXM

#8 3⁄4" .306/.322 .164 T08J075PXC T08J075PXM

#10 3⁄4" .357/.373 .190 T10J075PXC T10J075PXM

#6 1" .256/.270 .138 T06J100PXC T06J100PXM

#8 1" .306/.322 .164 T08J100PXC T08J100PXM

#10 1" .357/.373 .190 T10J100PXC T10J100PXM

#12 1" .407/.425 .216 T12J100PXC T12J100PXM

#14 1" .473/.492 .242 T14J100PXC T14J100PXM

#8 1 1⁄4" .306/.322 .164 T08J125PXC T08J125PXM

#10 1 1⁄4" .357/.373 .190 T10J125PXC T10J125PXM

#12 1 1⁄2" .407/.425 .216 T12J150PXC T12J150PXM

#14 1 1⁄2" .473/.492 .242 T14J150PXC T14J150PXM

#12 2" .407/.425 .216 T12J200PXC T12J200PXM

#14 2" .473/.492 .242 T14J200PXC T14J200PXM

316 Stainless Steel, Pan Head

HAND-DRIVE SCREWS | Sharx™ Marine Screws

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


76



CartonCount

5 lb.Item No.

1 lb. Item No.


Bucket Item No.

Deck PackItem No.

Availablein 316*







#7 3" 98 2000 S07300FB5 S07300FB1 S07300FBC S07300FBB S07C300PAK


#9 4" 61 1000 S09400FB5 S09400FB1 S09400FBC S09400FBB — —


• Type-17 point for fast starts• Coarse threads approximately 2⁄3 up the shank draw board tightly to the substrate• Pre-drilling recommended near board ends to prevent splitting• Use with stable woods and wood substitutes when screw heads need to be hidden• #7 screw has 0.230" head diameter and #1 square drive recess• #9 x 31⁄2" screw has 0.250" head diameter and #1 square drive recess• #9 x4" screw has 0.250" head diameter and #2 square drive recess• Choose type 316 for seaside applications and superior corrosion resistance• Bucket = 25 lbs.



Deck Packs contain enough screws to fasten 100 sq. ft. (6" nominal boards on 16" centers).Bulk Cartons contain enough screws to fasten 500 sq. ft. (6" nominal boards on 16" centers).

!

Size Length Carton Count Item No.

#8 1" 100 S08C100TSC

#8 1" 1000 S08C100TSM

#8 1" 2000 S08C100TSB

#8 1 1⁄4" 100 S08C125TSC

#8 1 1⁄4" 1000 S08C125TSM

#8 1 1⁄2" 100 S08C150TSC

#8 1 1⁄2" 1000 S08C150TSM

#8 2 1⁄2" 100 S08C250TSC

#8 2 1⁄2" 1000 S08C250TSM

305 Stainless Steel

• #2 square drive truss head, coarse thread similar to Swaneze™ screws• Fasten all materials to wood or wood-substitute materials• Pre-drilling recommended – dependent on substrate

HAND-DRIVE SCREWS | Truss Head, Coarse Thread, Square Drive

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


77

COMPOSITES & FIBERGLASS Hand-Drive Screws / Hand-Drive Nails


#7 1 5⁄8" 100 S07C162X0C

#7 1 5⁄8" 1000 S07C162X0M

#7 2 1⁄4" 100 S07C225X0C

#7 2 1⁄4" 1000 S07C225X0M

#7 3" 100 S07C300X0C

#7 3" 1000 S07C300X0M

305 Stainless Steel

• Type-17 point for fast starts• Assemblies provide weathertight seal for use in exterior sheathing and roofi ng applications• Washers are 302 stainless steel bonded to neoprene and 5⁄8" in diameter• Other sizes available – contact Simpson Strong-Tie for details• #1 square drive

HAND-DRIVE SCREWS | Swaneze™ Trim Head, with Sealing Washers


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.

Item No.Bucket













30d 4 1⁄2" 6 .203" 7⁄16" 22 S30ACN25 S30ACN5 S30ACN1 —


60d 6" 4 .238" 15⁄32" 12 S60ACN25 S60ACN5 S60ACN1 —

70d 7" 4 .238" 15⁄32" 10 S70ACN25 S07ACN5 S70ACN1 —

• All-around, general purpose structural nails with the heft to penetrate even the toughest seasoned timber

• First choice for construction of permanent wood foundations by the ANSI/AF&PA Permanent Wood Foundations Design Specifi cations

• Annular ring nails for greater pull-out resistance• Also available in screw shank – call for details• Choose type 316 for seaside applications and superior corrosion resistance• Bucket = 25 lbs.


HAND-DRIVE NAILS | Un-Common™ Common Ring Shank


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


78

METAL FRAMING

Metal FramingOur innovative stainless-steel, self-drilling screws are fashioned from heat-treated AISI type 410 alloy and coated to facilitate installation and add a secondary defense against corrosion. Our Billy Goat™ bugle head and trim-head screws are your best option for attaching wood, plywood or fi ber cement to steel studs. They’re available in a variety of head, thread and drive confi gurations to match a variety of applications.

Metal LathOur self-drilling K-Lath screws feature a phillips-drive recess and a large modifi ed truss head. These screws combine a low-profi le head with a large bearing surface to make this fastener ideal for holding lath to metal stud, or attaching plywood to metal. The shorter lengths are ideal for attaching one metal stud to another.

METAL FRAMING

Hand-Drive ScrewsSelf-Drilling, Bugle Head, Billy Goats™ .................................................. 79

Self-Drilling, Trim Head, Billy Goats™ ................................................... 79

Self-Drilling, Flat Head with Wings, Billy Goats™ .................................. 80

Self-Drilling, Wafer Head with Wings, Billy Goats™ .............................. 80

Self-Drilling, Marutex, Hex Washer Head, Billy Goats™ .........................81

Self Drilling, Fiber Cement, Metal Stud, Billy Goats™ ........................... 82

Self-Drilling, K-Lath Modifi ed Truss Head, Billy Goats™ ......................... 82

Nominal Screw Size Point Style Recommended

Steel ThicknessRecommended

Drill Speed (R.P.M.)

#6 No. 2 0.059 – 0.083" 2500 Max.

#8 No. 2 0.059 – 0.110" 2500 Max.

#8 No. 3 0.098 – 0.142" 2500 Max.

#10 No. 2 0.059 – 0.142" 2500 Max.

#10 No. 3 0.110 – 0.177" 2500 Max.

#12 No. 3 0.110 – 0.209" 1800 Max.

#12 No. 4 0.177 – 0.354" 1800 Max.

#12 No. 5 0.250 – 0.500" 1800 Max.

#14 No. 3 0.110 – 0.248" 1800 Max.

#14 No. 4 0.250 – 0.375" 1800 Max.

#14 No. 5 0.250 – 0.500" 1800 Max.

Standard Drilling Capacities and Drill Speed Recommendations for 410 Stainless-Steel Self-Drilling Screws

Our self-drilling screws are designed and engineered to secure a wide range of materials including fi berglass, composites, fi ber cement, wood, metal and gypsum board – to wood or metal studs. When it comes to installations involving masonry, you’ll fi nd that Simpson Strong-Tie offers the most diverse range of AISI type 410 stainless-steel screws on the market today.

Metal Framing

Metal Lath

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


79

METAL FRAMING


#6 1 1⁄4" 100 F06T125BDC#6 1 1⁄4" 1000 F06T125BDM#6 1 1⁄4" 5000 F06T125BDB#8 1 5⁄8" 100 F08T162BDC#8 1 5⁄8" 1000 F08T162BDM#8 1 5⁄8" 3000 F08T162BDB#8 2" 100 F08T200BDC#8 2" 1000 F08T200BDM#8 2" 2500 F08T200BDB#10 2 1⁄2" 100 F10T250BDC#10 2 1⁄2" 1000 F10T250BDM#10 2 1⁄2" 2000 F10T250BDB#10 3" 100 F10T300BDC#10 3" 1500 F10T300BDB#10 3 1⁄2" 100 F10T350BDC#10 3 1⁄2" 1000 F10T350BDB

410 Stainless Steel

• Fasten wood, plywood and OSB panels to steel studs• #2 square-drive bugle heads drive fl ush with work surface• Tapping screw threads, #3 drill points• Drilling thickness capacities: up to .083" (68 mils, 14 ga.) for #6,

up to .142" (118 mils, 10 ga) for #8 and up to .177" for #10

HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Bugle Head


#7 1 5⁄8" 100 F07T162TDC#7 1 5⁄8" 1000 F07T162TDM#7 1 5⁄8" 5000 F07T162TDB#7 2 1⁄4" 100 F07T225TDC#7 2 1⁄4" 1000 F07T225TDM#7 2 1⁄4" 4000 F07T225TDB#7 3" 100 F07T300TDC#7 3" 1000 F07T300TDM#7 3" 2000 F07T300TDB

410 Stainless Steel

• Attach wood siding, wood panels and metal trim to steel studs• #1 square drive, .230" head diameter, #3 drill point• Threaded 2⁄3 of overall length• Drilling thickness capacity: up to .125" (111 mils, 11 ga)

HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Trim Head

For more information on drilling thickness capacities and drill speed recommendations see page 78.



C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


80

METAL FRAMING Hand-Drive Screws


#10 1 7⁄16" 100 F10C144WDC

#10 1 7⁄16" 1000 F10C144WDM

#10 1 7⁄16" 4500 F10C144WDB

410 Stainless Steel

• Attach plywood and OSB panels to steel studs• Machine-screw thread, threaded full length, #3 drill point• Wings above drill point provide clearance hole in work piece so it won’t climb up

the shank and break off as point engages the steel substrate• #2 Phillips drive• 0.450" diameter head

HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Wafer Head with Wings


Drill Point Size Carton Count Item No.

#12 2" 3⁄8" #3 100 F12C200FDC

#12 2" 3⁄8" #3 1000 F12C200FDM

#12 2" 3⁄8" #3 2500 F12C200FDB

#12 2 1⁄2" 3⁄8" #3 100 F12C250FDC

#12 2 1⁄2" 3⁄8" #3 1000 F12C250FDM

#12 2 1⁄2" 3⁄8" #3 1800 F12C250FDB

#14 3 1⁄4" 15⁄32" #4 100 F14C325FDC

#14 3 1⁄4" 15⁄32" #4 1000 F14C325FDM

410 Stainless Steel

• Fasten wood, plywood and fi ber cement to heavier steel – up to .209" thick• #3 square drive• Machine screw thread, threaded full length• 2 1⁄2" length for 2x4 wood header; 2" length for 1" and 5⁄4" boards• Flat countersunk head with self-countersinking nibs• Shank slot enhances thread formation in steel and removes exhaust• Wings above drill point provide clearance hole in work piece so it won’t climb up

the shank, then break off as point engages the steel substrate• Drilling thickness capacities: up to .209" (171 mils, 7 ga) for #12,

up to .250" (229 mils, 3 ga) for #14

HAND-DRIVE SCREWS | Billy Goats™, Self-Drilling, Flat Head with Wings




C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


81


Size Length Hex HeadSize Carton Count Item No.

#8 1⁄2" 1⁄4" 100 X08050HDUC

#8 1⁄2" 1⁄4" 1000 X08050HDUM

#8 3⁄4" 1⁄4" 100 X08075HDUC

#8 3⁄4" 1⁄4" 1000 X08075HDUM

#8 1" 1⁄4" 100 X08100HDUC

#8 1" 1⁄4" 1000 X08100HDUM

#10 1⁄2" 5⁄16" 100 X10050HDUC

#10 1⁄2" 5⁄16" 1000 X10050HDUM

#10 3⁄4" 5⁄16" 100 X10075HDUC

#10 3⁄4" 5⁄16" 1000 X10075HDUM

#10 1" 5⁄16" 100 X10100HDUC

#10 1" 5⁄16" 1000 X10100HDUM

#10 1 1⁄2" 5⁄16" 100 X10150HDUC

#10 1 1⁄2" 5⁄16" 1000 X10150HDUM

#12 3⁄4" 5⁄16" 100 X12075HDUC

#12 3⁄4" 5⁄16" 1000 X12075HDUM

#12 1" 5⁄16" 100 X12100HDUC

#12 1" 5⁄16" 1000 X12100HDUM

#12 1 1⁄2" 5⁄16" 100 X12150HDUC

#12 1 1⁄2" 5⁄16" 1000 X12150HDUM

#12 2" 5⁄16" 100 X12200HDUC

#12 2" 5⁄16" 1000 X12200HDUM

#12 2 1⁄2" 5⁄16" 100 X12250HDUC

#12 2 1⁄2" 5⁄16" 1000 X12250HDUM

#12 3" 5⁄16" 100 X12300HDUC

#12 3" 5⁄16" 1000 X12300HDUM

#14 3⁄4" 3⁄8" 100 X14075HDUC

#14 3⁄4" 3⁄8" 1000 X14075HDUM

#14 1" 3⁄8" 100 X14100HDUC

#14 1" 3⁄8" 1000 X14100HDUM

#14 1-" 3⁄8" 100 X14150HDUC

#14 1-" 3⁄8" 1000 X14150HDUM

#14 2" 3⁄8" 100 X14200HDUC

#14 2" 3⁄8" 1000 X14200HDUM

#14 2 1⁄2" 3⁄8" 100 X14250HDUC

#14 2 1⁄2" 3⁄8" 1000 X14250HDUM

#14 3" 3⁄8" 100 X14300HDUC

#14 3" 3⁄8" 1000 X14300HDUM

Marutex

• Stainless-steel self-drillers for the most demanding projects, features the drilling capabilities of 410 stainless with increased corrosion resistance

• Will withstand over 300 hours salt spray with no oxidation• Rockwell C-53 typical hardness• Magnetic – heat-treated and passivated chrome/moly alloy• Indented hex head, tapping screw thread, #3 drill point• Screws are available with bonded sealing washers, please call for details

HAND-DRIVE SCREWS | Billy Goats™, Marutex, Self-Drilling, Hex Washer Head

Many of our 410SS screws are coated to insure better corrosion resistance and ease of installation. Grade 410 stainless steel can be hardened through heat treatment giving it the ability to drill through metal. It does not offer the same level of corrosion resistance of either type 305 or 316 stainless steel.

!


C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


82



• Fasten fi ber cement through furring strips to steel studs• #2 square drive, #3 drill point• Wafer head• Threaded to within 5⁄16" of top of head• Self-countersinking nibs under head ensure seating of screw heads fl ush with work surface

HAND-DRIVE SCREWS | FY-CEM Billy Goats™, Self-Drilling, Fiber-Cement Screws, Metal Stud

Size Length Head Size Carton Count Item No.

#8 1 5⁄8" .390" 100 F08T162WDC

#8 1 5⁄8" .390" 1000 F08T162WDM

#8 1 5⁄8" .390" 3000 F08T162WDB

#8 2 1⁄4" .390" 100 F08T225WDC

#8 2 1⁄4" .390" 1000 F08T225WDM

#8 2 1⁄4" .390" 2500 F08T225WDB

410 Stainless Steel

HAND-DRIVE SCREWS | K-Lath Modifi ed Truss Head, Self-Drilling


#8 9⁄16" 100 F08T056KDC

#8 9⁄16" 1000 F08T056KDM

#8 9⁄16" 8000 F08T056KDB

#8 3⁄4" 100 F08T075KDC

#8 3⁄4" 1000 F08T075KDM

#8 3⁄4" 6000 F08T075KDB

#8 1 1⁄4" 100 F08T125KDC

#8 1 1⁄4" 1000 F08T125KDM

#8 1 1⁄4" 4000 F08T125KDB

#8 1 5⁄8" 100 F08T162KDC

#8 1 5⁄8" 1000 F08T162KDM

#8 1 5⁄8" 3000 F08T162KDB

#8 2" 100 F08T200KDC

#8 2" 1000 F08T200KDM

#8 2" 2500 F08T200KDB

410 Stainless Steel

• For attaching metal lath to 14- to 20-gauge steel studs • Tapping screw threads, #3 drill point• #2 Phillips drive



C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


83

SPECIALTY ITEMS

Specialty NailsSimpson Strong-Tie is proud to be one of the last remaining manufacturers of stainless-steel and copper alloy nails in the United States. We specialize in AISI grade 304 and 316 stainless steel, aluminum, brass, commercial bronze, copper, monel, and silicon bronze.

Fence Staples and Hog RingsFence staples and hog rings have plenty of practical applications. Finding them in stainless steel, however, is not so easy. While we stock both in AISI grade 304 stainless steel, certain sizes are available in alternate alloys including AISI grade 316 and silicon bronze – please call for current availability.

Specialty ToolsSwan Secure tools are offered to help our customers – from contractors to resourceful home owners – make the best use of their time and skills. Our Drill N’ Drive™ pre-drills and countersinks for #7 trim-head screws, an absolute must for anyone working with tropical hardwoods such as Ipê. Our premium driver bits are US-made and custom fi t to ensure maximum reliability and bit life.

SPECIALTY ITEMS

Specialty Hand-Drive NailsMarine, Sea-Cure™ ........................................................................... 84Fencing ............................................................................................. 85Custom-Order .................................................................................. 85

Traditional FastenersFencing Staples ................................................................................ 85Hog Rings ......................................................................................... 85

Special ToolsPremium Driver Bits ......................................................................... 86Drill N’ Drive™ ................................................................................... 86

Special ApplicationsIpê Wood Plugs .................................................................................87Storm-Panel Screw ...........................................................................87

We listen carefully to the needs of our customers and actively strive to provide innovative, problem-solving products in a timely and responsible manner. Our manufacturing facility can produce custom nails to unique specifi cations and we stock the largest assortment of top quality, corrosion resistant stainless-steel fasteners available.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


84

SPECIALTY ITEMS

• Special selection of large-headed nails for wooden boat building and repair• Large bearing surface under heads for new construction and re-nailing projects• Annular ring threads offer greater pull-out resistance• Silicon bronze offers resistance to stress corrosion cracking under nail heads

in salt water applications• Monel® is a nickel/copper alloy formulated for optimum service life in salt-water applications.

It is required by the Coast Guard for refastening wooden boats in commercial service

SPECIALTY NAILS | Sea-Cure™ Marine

Stainless Steel, Silicon Bronze, Commercial Bronze, Monel


HeadDiameter

Approx. Count per lb. SS

Approx. Countper lb. Cu Alloy

25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

3⁄4" 15 .072" 3⁄16" 1050 913 S15075SC25 S15075SC5 S15075SC13⁄4" 14 .083" 7⁄32" 757 664 S14075SC25 S14075SC5 S14075SC17⁄8" 14 .083” 7⁄32" 657 617 S14087SC25 S14087SC5 S14087SC1

1" 15 .072" 3⁄16" 807 689 S15100SC25 S15100SC5 S15100SC1

1" 14 .083" 7⁄32" 622 536 S14100SC25 S14100SC5 S14100SC1

1" 12 .109" 17⁄64" 364 303 S12100SC25 S12100SC5 S12100SC1

1 1⁄4" 14 .083" 7⁄32" 473 424 S14125SC25 S14125SC5 S14125SC1

1 1⁄4" 12 .109" 17⁄64" 272 245 S12125SC25 S12125SC5 S12125SC1

1 1⁄2" 14 .083" 7⁄32" 413 374 S14150SC25 S14150SC5 S14150SC1

1 1⁄2" 12 .109" 17⁄64" 228 204 S12150SC25 S12150SC5 S12150SC1

1 1⁄2" 10 .134" 3⁄8" 147 132 S10150SC25 S10150SC5 S10150SC1

1 3⁄4" 12 .109" 17⁄64" 193 179 S12175SC25 S12175SC5 S12175SC1

1 3⁄4" 10 .134" 3⁄8" 130 118 S10175SC25 S10175SC5 S10175SC1

2" 12 .109" 17⁄64" 175 161 S12200SC25 S12200SC5 S12200SC1

2" 10 .134" 3⁄8" 114 104 S10200SC25 S10200SC5 S10200SC1

2" 8 .165" 7⁄16" 75 65 S8200SC25 S8200SC5 S8200SC1

2 1⁄2" 10 .134" 3⁄8" 94 83 S10250SC25 S10250SC5 S10250SC1

2 1⁄2" 8 .165" 7⁄16" 62 54 S8250SC25 S8250SC5 S8250SC1

3" 10 .134" 3⁄8" 79 71 S10300SC25 S10300SC5 S10300SC1

3" 9 .148" 3⁄8" 67 58 S9300SC25 S9300SC5 S9300SC1

3" 8 .165" 7⁄16" 51 45 S8300SC25 S8300SC5 S8300SC1

3" 6 .203" 1⁄2" 34 31 S6300SC25 S6300SC5 S6300SC1

3 1⁄4" 9 .148" 3⁄8" 60 52 S9325SC25 S9325SC5 S9325SC1

3 1⁄4" 8 .165" 7⁄16" 48 43 S8325SC25 S8325SC5 S8325SC1

3 1⁄2" 8 .165" 7⁄16" 44 40 S8350SC25 S8350SC5 S8350SC1

3 1⁄2" 6 .203" 1⁄2" 29 26 S6350SC25 S6350SC5 S6350SC1

4" 6 .203" 1⁄2" 25 23 S6400SC25 S6400SC5 S6400SC1

4" 4 .238" 9⁄16" 18 17 S4400SC25 S4400SC5 S4400SC1

4 1⁄2" 6 .203" 1⁄2" 22 20 S6450SC25 S6450SC5 S6450SC1

4 1⁄2" 4 .238" 9⁄16" 16 15 S4450SC25 S4450SC5 S4450SC1

5" 6 .203" 1⁄2" 19 18 S6500SC25 S6500SC5 S6500SC1

5" 4 .238" 9⁄16" 15 14 S4500SC25 S4500SC5 S4500SC1

6" 4 .238" 9⁄16" 12 11 S4600SC25 S4600SC5 S4600SC1

* For items in 316 stainless steel, substitute the letter “T” as the fi rst character of the item number; for silicon bronze, the letter “I”; for commercial bronze, the letter “O”; for Monel, the letter “M”.

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


85

SPECIALTY ITEMS


DiameterHead

DiameterApprox.

Count per lb.25 lb.

Item No.5 lb.

Item No.1 lb.


5d 1 3⁄4" 12 .109" 15⁄64" 193 S5FNX25 S5FNX5 S5FNX1

6d 2" 12 .109" 15⁄64" 175 S6FNX25 S6FNX5 S6FNX1

• Prevent unsightly streaks and stains on any wood or vinyl fence• Checker-patterned head blends with wood texture, serves to diffract sunlight and

accepts surface fi nishes• Annular ring threads reduce nail-head popping• Choose type 316 for seaside applications and superior corrosion resistance

SPECIALTY NAILS | Fencing



Gauge Length Approx. Count per lb.

25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

Availablein 316*

13 1" 291 S13100FS25 S13100FS5 S13100FS1 —

13 1 1⁄4" 202 S13125FS25 S13125FS5 S13125FS1

10 2" 66 S10200FS25 S10200FS5 S10200FS1 —


TRADITIONAL FASTENERS | Fencing Staples


Simpson Strong-Tie is proud to be one of the last remaining manufacturers of stainless-steel and copper-alloy nails in the United States. While we specialize in AISI-type 304 and 316 stainless steel, aluminum, brass, commercial bronze, copper, monel and silicon bronze, exotic alloys pose no problem – provided their mechanical properties are within our manufacturing capabilities. Call today with your requirements and one of our product specialists will be ready to assist you.

SPECIALTY NAILS | Custom Order

Gauge Width Open

Width Across

Approx. Countper lb.

25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

12 .95" 1.82" 111 S12131HR25 S12131HR5 S12131HR1

304 Stainless Steel, Blair Shaped

TRADITIONAL FASTENERS | Hog Rings

Gauge Width Open

Width Across

Approx. Countper lb.

25 lb. Item No.

5 lb. Item No.

1 lb. Item No.

13 .812" 1.57" 204 S13075HR25 S13075HR5 S13075HR1

304 Stainless Steel, #3 Pre-Bent, Hill Pattern (pictured)

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN

C.


86

SPECIALTY FASTENERS

SPECIALTY TOOLS | Drill ‘n Drive™

Our new #7 Drill ‘n Drive™ makes pre-drilling, countersinking and driving screws easy – all without having to re-chuck your drill – just drill, release, fl ip, lock and drive. The tool features a built-in hex key for replacing or changing driver and drill bits as well as adjusting pilot hole depth. A 1⁄8" replacement drill bit and our new T-15 and #1 square driver bits are included. Made in the U.S.A., with a limited lifetime warranty.

Screw Size Drill Bit Countersink Diameter

Countersink Angle

Driver Bits (included) Item No.

#7 .95" 1⁄4" 55° T-15 + #1 SQ. DRILLDRIVE

SPECIALTY TOOLS | Premium Driver BitsMade in the U.S.A., our new industrial-grade driver bits are specially designed for a secure fi t with the recess of Simpson Strong-Tie® Swan Secure stainless-steel screws. Available in both square and six-lobe drive confi gurations, our bits will outperform sub-standard imports commonly prone to stripping and cam-out.

Drive Bit Length Item No.

#1 2" SSBIT1-2

#2 2" SSBIT2-2

#3 2" SSBIT3-2

Driver Bits – Square Drive

Drive Bit Length Item No.

T-15 2" SSBIT15-2

T-20 2" SSBIT20-2

T-25 2" SSBIT25-2

Driver Bits – Six-Lobe Drive

C-SS

TSW

AN09

©20

09 S

IMPS

ON S

TRON

G-TI

E CO

MPA

NY IN


87

SPECIALTY FASTENERS

SPECIAL APPLICATIONS | Storm-Panel Screw

• Ideal for attaching storm panels to wood, concrete and masonry• Save time and money with a single installation• The screw is made of type 305 stainless steel for good corrosion resistance

INSTALLATION1. Drill a hole in the concrete or masonry base material using the drill bit provided.

To pre-drill into wood, use a 3/16" bit2. Position the panel and drive the screw using the hex driver bit (included).

Drive the screw deep enough so that the bottom of the threads for the wing nut are slightly below the surface of the panel

3. Secure the panel with the wing nut4. To remove panels – remove the wing nut, remove the panel and cover

the threads on the screw with the plastic cap

!

Each pack contains:

(25) Stainless-steel storm-panel screws 1⁄4" x 3 7⁄16"(25) 1⁄4" zinc die-cast washered wing nuts(25) White plastic caps to protect threads after panels are removed(1) Hex driver bit for panel screws(1) 0.234" x 4 1⁄2" carbide-tipped drill bit

Plug Diameter Plug Length Count per pkg. Item No.

3⁄8" 7⁄16" 100 WDPLUG-100

Size Length Item No.

1⁄4" 3 7⁄16" SPS25344-KT

SPECIALTY PLUGS | Wood Plugs (Ipê)• Made of high quality Ipê and tapered for ease of use• For use on decks using the EB-TY® system (fi rst boards, aprons, etc.);

also stairs, railings

Bostitch, Senco, Paslode, Dewalt, Duo-Fast, Fasco, Makita, Max, Porter-Cable, Stan-Tech, Spot Nails, Craftsman, Robertson-Holzer, Power Nail, Porta-Nails, Primatech, Muro, Grabber, Pam and Milwaukee are registered trademarks of their respective companies and/or parent companies.


catalog: swan secure fasteners (c-sstswan09) · c-sstswan09 ©2009 simpson strong-tie company inc....

Documents