Innovative Control Systems

1349 Jacobsburg Road • Wind Gap, PA 18091

610.881.8000 • 610.881.8120 – fax • www.washnet.com

Instructions for

Programming Multiple Cassettes

for Fujitsu® Brand Bill Dispensers

6/9/2010 2Copyright © 2009 Innovative Control Systems, Inc.

Before You Begin

• Read all instructions first.

• A qualified ICS technician can help ensure

these instructions are followed correctly.

Contact ICS for support.

Remove the Bill Cassette

• Remove the bill dispenser cassette.

• Place on clean, dry work surface.

6/9/2010 3Copyright © 2009 Innovative Control Systems, Inc.

Required Tools

• #2 Phillips Screwdriver

6/9/2010 4Copyright © 2009 Innovative Control Systems, Inc.

Reading the Cassette Table

6/9/2010 5Copyright © 2009 Innovative Control Systems, Inc.

• A cassette table shows

you how to program a

cassette.

• The 14 rows are labeled

A(1) through N(E). The

columns are labeled

“d”, “c”, “b” and “a”.

• Look closely at the

holes above each

column letter to see

which positions are

filled.

RowsColumns

Reading the Cassette Table

• You will use magnets to

fill the positions.

Magnets are applied to

the back-side of the

cover.

• Black circles in the

table indicate a position

should be filled.

• White circles indicate a

position should be

empty.

6/9/2010 6Copyright © 2009 Innovative Control Systems, Inc.

RowsColumns

Reading the Cassette Table

• Look at row A(1). It

shows that magnets

should be applied to

positions “d”, “c”, and

“b”. Position “a”

should be left empty.

• Once you apply the

magnets in this way,

the cassette is

programmed as number

A(1).

6/9/2010 7Copyright © 2009 Innovative Control Systems, Inc.

RowsColumns

Removing the Faceplate

6/9/2010 8Copyright © 2009 Innovative Control Systems, Inc.

REMOVE SCREW

• Remove the bill dispenser from the unit.

• Open the bill dispenser lid and locate the faceplate.

• Remove one screw on the left side of the faceplate.

Removing the Faceplate

6/9/2010 9Copyright © 2009 Innovative Control Systems, Inc.

• Remove faceplate.

Removing the Bracket

6/9/2010 10Copyright © 2009 Innovative Control Systems, Inc.

• Locate bracket behind faceplate.

• Loosen two screws on bracket.

Removing the Bracket

6/9/2010 11Copyright © 2009 Innovative Control Systems, Inc.

• Remove bracket.

Locating the Magnets

6/9/2010 12Copyright © 2009 Innovative Control Systems, Inc.

• Locate magnets on reverse side of

bracket.

MAGNETS

Positioning the Magnets

6/9/2010 13Copyright © 2009 Innovative Control Systems, Inc.

• Reposition magnets as required.

MAGNETS IN POSITION A(1) MAGNETS IN POSITION B(2)

Replacing the Bill Dispenser

• Replace the bill dispenser following the

instructions in reverse.

• Attach bracket.

• Attach faceplate.

• Replace bill dispenser in unit.

6/9/2010 14Copyright © 2009 Innovative Control Systems, Inc.

6/9/2010 15Copyright © 2009 Innovative Control Systems, Inc.

• Contact ICS Support for more information:610-881-8001 – Direct

1-800-642-9396 – Toll free

• Information in this presentation is subject to change without notice. Companies, names and data used in examples within the presentation are fictitious unless otherwise noted. No part of this presentation may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Innovative Control Systems, Inc.

• ICS is not responsible for damage, bodily harm, loss of business, etc. due to the information contained in this document. Refer to the standard sales agreement and warranty information that came with your ICS product for more details.

Auto Sentry, Lube Master and Tunnel Master are registered trademarks of Innovative Control Systems, Inc.

Touch ‘N Clean and Wash Valet are trademarks of Innovative Control Systems, Inc.

Fujitsu is a registered trademark of Fujitsu Limited Corporation, Japan .

DeLaRue is a registered trademark of De la Rue Holdings, plc.

Talaris is a registered trademark of Talaris Holdings Limited.