case components * composants du boîtier * guía de instalación · 2020. 7. 13. · * case...
TRANSCRIPT
* * Composants du boîtier * Case components Guía de instalación
* * * Gehäusekomponenten機殼部品介紹
- 1 -
IO ports: USB 3.0 x 2, USB 3.1 x 1(Type-c) HD audio & mic,
ARGB control button (M: Mode, C: Color)
USB 3.0 x 2
Power switch / reset button
J
ARGB LED strip
Supporting 120 mm fan x 3 or 140 mm fan x 2 or 360 mm radiator x 1
Removable fan/SSD tray: Supporting 120 mm fan x 3 or 140 mm fan x 2 or 360 mm radiator x 1 or 2.5” SSD x 3
G H
I
J
K
Additional SSD trays x 3: Supporting 120 mm fan x 3 or 360 mm radiator x 1 or 2.5” SSD x 3
Removable SSD tray: Supporting 2.5” SSD x 3
Supporting 120mm fan x 1
Hot swappable drive trays: Supporting 3.5” HDD x 4 or 2.5” SSD x 4 or ATX PSU x 2
K PSU tray: Supporting ATX PSU x 1
- 2 -
* 零件盒部品一覽表
* Hardware list * Lista de materiales* Liste des pièces* Hardwareliste *
Rubber padfor PSU mounting
Screwsfor 2.5" SSD mount
24 pcs
d
for motherboard mountStand-off bolt Screws
for motherboard & 2.5" SSD mount
(Spare parts)
b
3 pcs
g
28 pcs
a
Screws for PSU mounting
c
8 pcs
16 pcs
Screwsfor 3.5" HDD mount
e f
4 pcs
Velcrofor cable management
g
Exceeded quantity are spare parts.
多餘的零件數量是備品.
Zusätzliche Teile können als Ersatzteile verwendet werden.
Les pièces supplémentaires sont des pièces de rechange.
Exceeded quantity are spare parts.
For Graphics Card Anti-Sag Bracket (GB-001) installation
4 pcs2 pcs2 pcs
2 pcs 2 pcs 2 pcs
Screwsfor fan mounting
4 pcs
d
2 pcs
* Remove top panel* 卸下頂部面板* Retirer le panneau supérieur* Entfernen Sie die obere Abdeckung* Retire el panel superior*トップパネルを取り外す
* Remove side glass & front * 卸下側面玻璃及前面玻璃* Enlever le verre latéral et frontal* Entfernen Sie die Seiten- und Frontscheibe* Retire el vidrio lateral y frontal*
glass
サイド&フロントガラスを取り外す
- 3 -
Peel off the protective film on both sides
! Attention:
1
2
3
Pull to release the glass.
- 4 -
Instalación de la fuente de alimentación **
PSU installation*電源供應器安裝*Installation du plateau du bloc d'alimentation
*
* PSU-Einsatz installieren
1
2
c
g
* Kabel installieren Guía de instalación de los cables
電源/系統指示燈接線定義
Diagramme d’installation des câbles
*
* Cable guideinstallation
***
POWER SWBLACK / WHITE -
BLACK +
HDD LEDBLACK / WHITE -
BLACK +
RESET SWBLACK / WHITE -BLACK +
POWER LED
POWER LEDBLACK +
BLACK / WHITE -
To install 2 more PSUs, remove the 2 hot swappable drive trays.
- 5 -
To install a special spec MB (ex. MB including a LED module and/or a thicker shield), please trim the rubber pads.!
- 6 -
1
2
3
1
2
e
Connecting to PSU
Connecting to MB
2.5" SSD / 3.5" HDD installation
Installation de 2.5" SSD / 3.5" HDD
2.5" SSD / 3.5" HDD-Installation
Instalación de 2.5" SSD / 3.5" HDD
a
2.5" SSD / 3.5" HDD
2.5" SSD / 3.5" HDD のインストール
- 7 -
Press to release the HDD tray
or
d
* * 2.5
* Instalación
* * 2.5" SSD-Installation
* 2.5" SSD installation
* 2.5" SSD 安裝
* Instalación de SSD 2.5"
* *
Installation de 2.5" SSD
2.5" SSD の取り付け *
3+1 additional SSD trays can be installed on the front right side and/or on the removable fan/SSD tray on the bottom
- 8 -
* * 2.5 * Instalación
*
* 2.5" SSD-Installation* 2.5" SSD installation
* 2.5" SSD 安裝 * Instalación de 2.5" SSD
*
*
Installation de 2.5" SSD 2.5" SSDの取り付け *
*** Gestion des câbles* Kabelmanagement* Mantenimiento de cable *
整線
ケーブル
Cable management
管理
f
Top
Bottom
*
灰塵濾網拆卸Remove the magnetic dust filters
*
* Retirez les filtres à air* Entfernen Sie Luftfilter * Retire los filtros de aire*
Side
HD AUDIO
BlueBlack purple
YellowGrayRed
108642
97531
GreenKeyOrangeN.C.GND+H.S. TUBE
USB 3.0
Supports motherboard USB 3.0 20 Pin header
11
20
10
1
** I/O port * Installation du port E/S* I/O-Port installieren* Instalación de los puertos de E/S*
I/O ports function
功能說明
I/O
USB 3.1 GEN.2
MO
DE
C
OLO
R
TY
PE
-CM
ICS
PK
US
B3.0
-2U
SB
3.0
-1P
_S
W/H
DD
9
— Mode 8 Lighting Effects:1. 1st-7th: MCU Built-in Lighting Mode2. 8th: Sync Up the ARGB Lighting With The Motherboard (1) Connecting The Header To The Motherboard (2) To Turn Off The Lighting, Press The Button For 3 Sec. To Turn It On, Press Again For 3 Sec
C- ColorPress C To Control The 7 Built-in Static Colors
M
C
- 10 -
LED control board
installationLED控制板安裝Installation du tableau de commande LEDInstallation der LED-steuerplatineInstalación del tablero de control LEDLEDコントロールボードの設置
******
+5V GNDD
ADDRESS LED HEADER
DI
MB-5V
GNDGND
5V
5V
GND
DO
5V
GND
DO
COLOR-SW
MODE-SW
MCU
EC1
JP4
U1
JP3
JP5
EC2
JP1
JP2
JP6
EC3ARGB LED strip on the front Already connected to the
Connecting to PSU
Putting the header of M|C button into this header
Connecting to MB
- 11 -
******
Graphics Card Anti-Sag Bracket (GB-001) installation
Carte Graphique installation du Support Anti-AffaissementGrafikkarten-Anti-Durchhang-HalterungTarjeta Gráfica de montaje en Soporte Antideslizamiento.
グラフィックカード垂れ防止ブラケットの取り付け
顯示卡支撐架安裝說明
EEB
- 12 -
Radiator & cooling support * 散熱器 & 水冷排支援*
*
Assistance radiateur et refroidissement
***
Model: O11DXL-1 Upright Display Card Kits
For EEB sized MB installation.
Model: O11DXL-2 E xtension panel
Kühler- und KühlungsunterstützungRadiador y soporte de refrigeración.
ラジエター&冷却サポート
*** Kits optionnels
選配套件Optional kits * Optionale Sets
* Kits opcionales *
200 mm PCI-e Express 16X Riser Card Adapter Extender Cable Kit.
E-ATX
- 13 -
167 mm
65 mm
50 mm
65 mm
65 mm
169 mm
446 mm