care and maintenance of the liko: mobile lifts ceiling lifts sit ......lift stretchers english...

14
1 Care and Maintenance of the Liko: Mobile Lifts Ceiling Lifts Sit to Stand Lifts Lift Stretchers English 7EN180818-02 2013-01-23 This instruction applies to Liko mobile lifts, ceiling lifts, sit to stand lifts, and lift stretchers, yet in this text we refer only to lifts. To avoid possible transmission of infectious disease, it is important to clean the lift if it has become soiled or if it is to be used by another patient. Also refer to your facility’s cleaning and disinfection policies for any additional guidelines on frequency. It is important to follow the recommendations in this manual to maintain the warranty and expected life time. This manual gives detailed cleaning and disinfecting procedures for Liko lifts. The instructions in this manual do not replace your facility’s cleaning and disinfection policies. This manual is intended for use by facility-approved persons only. To ignore this restriction could cause severe injury to people and serious damage to equipment. Liko/Hill-Rom recommends that the lift be disinfected prior to first use. Liko/Hill-Rom recommends to disinfect the lift prior to disposal in accordance with local environmental regulations. Liko’s products undergo continuous development, which is why we reserve the right to make product changes without prior notice. The only warranty Liko/Hill-Rom makes is the express written warranty extended on the sale or rental of its products. The information contained in this manual is subject to change without notice. Visit our website www.liko.com for updated versions of this manual or contact your local Liko/Hill-Rom representative for advice or more information. Safety recommendations Wear protective equipment according to manufacturer’s instruction and per facility protocol throughout the cleaning operations, such as: rubber gloves, goggles, apron, face mask and shoe covers. • Unplug mains (AC power source) before cleaning and disinfection. • Never clean the lift by pouring water on it, steam cleaning it, or by using a high-pressure jet. • Refer to the recommendations made by the cleaning and disinfecting product manufacturer. Inadequate cleaning may increase risk of cross contamination!

Upload: others

Post on 10-Feb-2021

3 views

Category:

Documents


0 download

TRANSCRIPT

  • 1

    Care and Maintenance of the Liko: Mobile Lifts Ceiling Lifts Sit to Stand Lifts Lift Stretchers

    English7EN180818-02

    2013-01-23

    This instruction applies to Liko mobile lifts, ceiling lifts, sit to stand lifts, and lift stretchers, yet in this text we refer only to lifts.

    To avoid possible transmission of infectious disease, it is important to clean the lift if it has become soiled or if it is to be used by another patient. Also refer to your facility’s cleaning and disinfection policies for any additional guidelines on frequency.

    It is important to follow the recommendations in this manual to maintain the warranty and expected life time.

    This manual gives detailed cleaning and disinfecting procedures for Liko lifts. The instructions in this manual do not replace your facility’s cleaning and disinfection policies.

    This manual is intended for use by facility-approved persons only. To ignore this restriction could cause severe injury to people and serious damage to equipment.

    Liko/Hill-Rom recommends that the lift be disinfected prior to first use.

    Liko/Hill-Rom recommends to disinfect the lift prior to disposal in accordance with local environmental regulations.

    Liko’s products undergo continuous development, which is why we reserve the right to make product changes without prior notice. The only warranty Liko/Hill-Rom makes is the express written warranty extended on the sale or rental of its products.

    The information contained in this manual is subject to change without notice. Visit our website www.liko.com for updated versions of this manual or contact your local Liko/Hill-Rom representative for advice or more information.

    Safety recommendations• Wear protective equipment according to manufacturer’s instruction and per facility protocol throughout the

    cleaning operations, such as: rubber gloves, goggles, apron, face mask and shoe covers.• Unplug mains (AC power source) before cleaning and disinfection.• Never clean the lift by pouring water on it, steam cleaning it, or by using a high-pressure jet. • Refer to the recommendations made by the cleaning and disinfecting product manufacturer.

    Inadequate cleaning may increase risk of cross contamination!

  • 27EN180818-02 www.liko.com

    App

    licat

    ion

    of c

    omm

    only

    use

    d C

    lean

    ing

    / Dis

    infe

    ctan

    ts o

    n Li

    ko p

    rodu

    cts

    Che

    mic

    al c

    lass

    Act

    ive

    ingr

    edie

    ntpH

    Cle

    aner

    s /

    Dis

    infe

    ctan

    t *)

    Man

    ufac

    ture

    r *)

    May

    not

    be

    used

    on

    the

    follo

    win

    g ite

    ms:

    Qua

    tern

    ary

    amm

    oniu

    m c

    hlor

    ide

    Did

    ecyl

    dim

    ethy

    l am

    mon

    ium

    chl

    orid

    e =

    8.70

    4%

    Alk

    yl d

    imet

    hyl b

    enzy

    l am

    mon

    ium

    chl

    orid

    e =

    8.19

    %9.

    0 –

    10.0

    in u

    seVi

    rex

    II (2

    56)

    John

    son/

    Div

    erse

    yFo

    ot re

    st fo

    r Sab

    ina™

    an

    d R

    oll-O

    n™

    Qua

    tern

    ary

    amm

    oniu

    m c

    hlor

    ide

    Alk

    yl d

    imet

    hyl b

    enzy

    l am

    mon

    ium

    chl

    orid

    e =

    13.2

    38%

    A

    lkyl

    dim

    ethy

    l eth

    ylbe

    nzyl

    am

    mon

    ium

    chl

    orid

    e =

    13.2

    38%

    9.5

    in u

    seH

    B Q

    uat 2

    5L3M

    Acc

    eler

    ated

    Hyd

    roge

    n P

    erox

    ide

    Hyd

    roge

    n P

    erox

    ide

    0.1

    -1.5

    %B

    enzy

    lAlc

    ohol

    : 1-5

    %H

    ydro

    gen

    Per

    oxid

    e 0.

    1 -1

    .5%

    Ben

    zylA

    lcoh

    ol: 1

    -5%

    3O

    xivi

    r Tb

    John

    son/

    Div

    erse

    yTh

    e lif

    t str

    aps

    for

    Gol

    vo™

    and

    cei

    ling

    lifts

    Phe

    nolic

    Orth

    o-P

    heny

    lphe

    nol =

    3.4

    0%

    Orth

    o-B

    enzy

    l-par

    a-C

    hlor

    ophe

    nol =

    3.0

    33.

    1 +/

    - 0.4

    in u

    seW

    exci

    deW

    exfo

    rd L

    abs

    Ble

    ach

    Sod

    ium

    hyp

    ochl

    orite

    12.2

    Dis

    patc

    hC

    alte

    chTh

    e lif

    t str

    aps

    for

    Gol

    vo™

    and

    cei

    ling

    lifts

    Alc

    ohol

    Isop

    ropy

    l alc

    ohol

    = 7

    0%5.

    0 –

    7.0

    Vira

    guar

    dVe

    ridie

    nH

    and

    cont

    rols

    for a

    ll lif

    tsQ

    uate

    rnar

    y am

    mon

    ium

    n-A

    lkyl

    dim

    ethy

    l ben

    zyl a

    mm

    oniu

    m c

    hlor

    ides

    = 0

    .105

    %n-

    Alk

    yl d

    imet

    hyl e

    thyl

    benz

    yl a

    mm

    oniu

    m c

    hlor

    ides

    = 0

    .105

    %11

    .5 -

    12.5

    CS

    IC

    entra

    l Sol

    utio

    ns In

    c.Vi

    king

    ™, L

    iko

    M22

    0™,

    Liko

    M23

    0™, U

    no™

    , Sa

    bina

    ™, G

    olvo

    ™,

    Liko

    Ligh

    t™, R

    oll-O

    n™,

    Liko

    rall™

    , Mul

    tiral

    l™B

    enzy

    l-C12

    -18-

    alky

    ldim

    ethy

    lam

    mon

    ium

    , ch

    lorid

    esB

    enzy

    l-C12

    -18-

    alky

    ldim

    ethy

    lam

    mon

    ium

    , chl

    orid

    es (2

    2 %

    )2-

    Phe

    noxy

    etha

    nol (

    20 %

    )Tr

    idec

    ylpo

    lyet

    hyle

    ngly

    cole

    ther

    (15

    %)

    Pro

    pan-

    2-ol

    (8 %

    )

    appr

    ox 8

    .6 in

    use

    Terr

    alin

    Pro

    tect

    Shü

    lke

    Foot

    rest

    for S

    abin

    a™

    and

    Rol

    l-On™

    Org

    anic

    per

    oxid

    e (ty

    pe E

    , sol

    id)

    Mag

    nesi

    um m

    onop

    erox

    ypht

    alat

    e he

    xahy

    drat

    e (5

    0-10

    0%)

    Ani

    onic

    sur

    fact

    ant (

    5-10

    %)

    Non

    ioni

    c su

    rfact

    ant (

    1-5%

    )

    5.3

    in u

    seD

    ism

    ozon

    Pur

    Bod

    eTh

    e lif

    t str

    aps

    for

    Gol

    vo™

    and

    cei

    ling

    lifts

    Eth

    anol

    Hyd

    roge

    n pe

    roxy

    de (2

    .5-1

    0 %

    )La

    uryl

    dim

    ethy

    lam

    ine

    oxid

    (0-2

    .5 %

    )E

    than

    ol (2

    .5-1

    0 %

    )

    7A

    niox

    y-S

    pray

    WS

    Ani

    osC

    ontr

    ol b

    ox fo

    r all

    mob

    ile li

    fts

    Troc

    lose

    ne s

    odiu

    mA

    dipi

    c ac

    id 1

    0-30

    %A

    mor

    phou

    s si

    lica

    < 1%

    Sod

    ium

    Tol

    uene

    sul

    phon

    ate

    5-10

    %Tr

    oclo

    sene

    sod

    ium

    10-

    30 %

    4-6

    in u

    seC

    hlor

    -Cle

    anG

    uest

    Med

    ical

    Ltd

    The

    lift s

    trap

    s fo

    r G

    olvo

    ™ a

    nd c

    eilin

    g lif

    ts

    *) O

    r equ

    ival

    ent

  • 37EN180818-02 www.liko.com

    Cleaning and Disinfection RecommendationsAll parts must be kept clean at all times in order to avoid the risk of infection. All necessary precautions must be taken to remove all visible stains and soiling.The cleaning and disinfecting method described below applies specifically to this device and all its accessories and is designed to save time and to help combat nosocomial infections more effectively.

    Equipment: • Protective equipment (such as: rubber gloves, goggles, apron, face mask and shoe covers) as recommended

    by the facility protocol and manufacturers instructions• Clean buckets• Cloths for washing and drying• Soft brush • Warm water• To find Cleaning / Disifectants compatible or not compatible for use on Liko’s products, follow the ”Application

    of commonly used Cleaning / Disinfectants on Liko products” at page 2 in this document.

  • 47EN180818-02 www.liko.com

    Viking™ liftCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. To have access to all

    areas run the lift into the highest and lowest positions and extend the base width adjustment entirely in and out. Remove the Battery to have access behind the battery.

    NOTE! Do not clean the piston rod! 4. Pay special attention to the following areas: • Sling bar (different designs) • Mechanical emergency lowering (different designs) • Handles • Hand control (different designs) • Emergency stop • Operation panel/display (where applicable) • Lever for base width adjustment (where applicable) • Pedal for base width adjustment (where applicable) • Locking handles • Wheels

    Wheels

    Sling bar Handles

    Locking handle

    Emergency stop

    Mechanical emergency

    lowering

    Lever for base width adjustment

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The control box may not be cleaned with Anioxy Spray or equivalent.

    BatteryHand control

    Pedal for base width adjustment

    Do not clean the piston rod!

    Control box

    Operation panel/ display

  • 57EN180818-02 www.liko.com

    Liko M220™/Liko M230™ liftsCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. To have access to all

    areas run the lift into the highest and lowest positions and extend the base width adjustment entirely in and out. Remove the Battery to have access behind the battery.

    NOTE! Do not clean the piston rod! 4. Pay special attention to the following areas: • Sling bar • Mechanical emergency lowering • Handles • Hand control • Emergency stop • Pedal for base width adjustment (where applicable) • Wheels

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The control box may not be cleaned with Anioxy Spray or equivalent.

    Pedal for base width adjustment

    Hand control

    Do not clean the piston rod!

    Sling bar

    Mechanical emergency lowering Handles

    Emergency stop

    Wheels

    Battery

    Control box

  • 67EN180818-02 www.liko.com

    Uno™ liftCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. To have access to all

    areas run the lift into the highest and lowest positions and extend the base width adjustment entirely in and out. Remove the Battery to have access behind the battery.

    NOTE! Do not clean the piston rod! 4. Pay special attention to the following areas: • Sling bar (different designs) • Mechanical emergency lowering • Handles • Hand control • Emergency stop • Lever for base width adjustment (where applicable) • Locking handles • Wheels

    Sling barHandles

    Locking handles

    Mechanical emergency lowering

    Emergency stop

    Wheels

    Hand control

    Lever for base width adjustment

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant. After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The control box may not be cleaned with Anioxy Spray or equivalent.

    BatteryControl box

    Do not clean the piston rod!

  • 77EN180818-02 www.liko.com

    Sabina™ liftCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. To have access to all

    areas run the lift into the highest and lowest positions and extend the base width adjustment entirely in and out. Remove the Battery to have access behind the battery. The calf strap may be machine washed 60-80°C (140-176°F), see ”Care and Maintenance of Liko Slings” for more information.

    NOTE! Do not clean the piston rod! 4. Pay special attention to the following areas: • Sling bar (different designs) • Side support (where applicable) • Handles • Mechanical emergency lowering (different designs) • Hand control • Emergency stop • Lower-leg support • Foot rest • Locking handles • Wheels • Lever for base width adjustment (where applicable)

    Lever for base width adjustment

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The control box may not be cleaned with Anioxy Spray or equivalent. The foot rest may not be cleaned with Terralin Protect, Virex II or equivalent. The leg support on Sabina II, S/N up to 460899 and leg support on Sabina 200, S/N up to 3501599 may only be cleaned with warm water and a facility approved neutral detergent. The leg support on Sabina II S/N from 460900 and leg support on Sabina 200, S/N from 3501600 may be cleaned with the recommended disinfectants.

    Side support

    Sling bar

    Lower-leg support

    Foot restLocking handles

    Locking handles

    Wheels

    Handles

    Emergency stop

    Hand control

    Battery

    Control box

    Mechanical emergency

    lowering

    Calf strap

    Product label with serial no. (S/N)

    Do not clean the piston rod!

  • 87EN180818-02 www.liko.com

    Lift strap

    Mechanical emergency lowering

    Arm rest

    Golvo™ liftCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. To have access to

    all areas run the lift into the highest and lowest positions and extend the base width adjustment entirely out. Remove the Battery to have access behind the battery. Lower the sling bar to get access to the whole lift strap.Fully extend the lift strap by using the emergency lowering. After cleaning the lift strap, and before you raise the sling bar, make sure the lift strap has dried. After the emergency lowering device is used, the lifting level needs to be restored; see the Instruction Guide for the Golvo lift.

    4. Pay special attention to the following areas: • Lift strap • Sling bar (different designs) • Arm rest • Mechanical emergency lowering • Hand control (different designs) • Handles • Operation panel (where applicable) • Emergency stop • Wheels

    Sling bar

    Handles

    Wheels

    Emergency stop

    Operation panel

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The control box may not be cleaned with Anioxy Spray or equivalent. The lift strap may not be cleaned with Oxivir Tb, Dispatch, Chlor-Clean, Dismozon Pur or equivalent.

    Hand control

    Control box

    Battery

  • 97EN180818-02 www.liko.com

    LikoLight™ liftCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. To have access to all

    areas run the lift into the highest and lowest positions and extend the base width adjustment entirely in and out. Remove the Battery to have access behind the battery.

    NOTE! Do not clean the piston rod! 4. Pay special attention to the following areas: • Sling bar (different designs) • Mechanical emergency lowering • Handles • Hand control • Emergency stop • Pedal for base width adjustment • Lever for base width adjustment (where applicable) • Locking handles • Wheels

    Sling bar

    Handles

    Locking handles

    Mechanical emergency lowering

    Emergency stop

    Wheels

    Hand control

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The control box may not be cleaned with Anioxy Spray or equivalent.

    Pedal for base width adjustment

    Lever for base width adjustment

    Battery

    Control box

    Do not clean the piston rod!

  • 107EN180818-02 www.liko.com

    Wheels

    Torso cushion

    Rear supports

    HandlesSafety lockSeat frame

    Lower-leg support

    Foot rest

    Locking handle

    Locking handles

    RollOn™ liftCleaning Instruction

    1. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be used to remove stains and resistant soil.

    2. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet.3. Pay special attention to the following areas: • Torso cushion • Safety lock • Handles • Seat frame • Raising handles • Rear supports • Locking handles • Lower-leg support • Foot rest • Wheels

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The foot rest may not be cleaned with Terralin Protect or Virex II or equivalent.

    Raising handles

  • 117EN180818-02 www.liko.com

    Likorall™ liftCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. Lower the sling bar to

    get access to the whole lift strap. After cleaning the lift strap and before you raise the sling bar, make sure the lift strap has dried.

    The Likorall lift with mechanical emergency lowering: fully extend the lift strap by using the mechanical emergency lowering. After cleaning the lift strap and before you raise the sling bar, make sure the lift strap has dried. After the mechanical emergency lowering device is used, the lifting level needs to be restored; see the Instruction Guide for the Likorall lift.

    4. Pay special attention to the following areas: • Lift strap • Electrical emergency lowering/raising • Emergency stop • Emergency stop cord • Mechanical emergency lowering (where applicable) • Sling bar (different designs) • Hand control (different designs) • Electrical emergency lowering device (where applicable)

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The lift strap may not be cleaned with Oxivir Tb, Dispatch, Chlor-Clean, Dismozon Pur or equivalent.

    Lift strap

    Mecanical emergency lowering

    Sling bar

    Emergency stop cord

    Emergency stop

    Electrical emergency lowering device

    Electrical emergency lowering/raising

    Hand control

  • 127EN180818-02 www.liko.com

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the lift, wipe the lift with a moist cloth using clean water to remove all disinfectant residue.

    The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The lift strap may not be cleaned with Oxivir Tb, Dispatch, Chlor-Clean, Dismozon Pur or equivalent.

    Multirall™ liftCleaning Instruction

    1. Unplug mains (AC power source) before cleaning and disinfection. 2. Clean the lift with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be

    used to remove stains and resistant soil.3. Wipe down the entire lift starting from the top down. Do not use a cloth that is dripping wet. Lower the sling bar to

    get access to the whole lift strap. After cleaning the lift strap and before you raise the sling bar, make sure the lift strap has dried.

    4. Pay special attention to the following areas: • Electrical emergency lowering/raising • Mechanical emergency lowering • Emergency stop • Handles • Lift strap • Hand control • Sling bar (different designs)

    Electrical emergency lowering/raising

    Lift strap

    Sling bar

    Emergency stop

    Hand control

    Handles

    Mechanical emergency lowering

  • 137EN180818-02 www.liko.com

    Lift StretchersCleaning Instruction

    1. Clean the stretcher with a moist cloth, using warm water and a facility approved neutral detergent. A soft brush can be used to remove stains and resistant soil.

    2. Wipe down the entire stretcher starting from the top down. Do not use a cloth that is dripping wet.

    DisinfectRepeat the cleaning instructions after reading the ”Application of commonly used Cleaning / Disifectants on Liko products” at page 2 in this document. Follow the manufacturer’s instructions for proper use of the disinfectant.After you disinfect the stretcher, wipe the stretcher with a moist cloth using clean water to remove all disinfectant residue.

    The stretcher may not be cleaned with CSI or equivalent.

    Liko FlexoStretch™/Liko UltraStretch™

    LikoStretch 1800™

    LikoStretch Mod 600 IC™

    LikoStretch 1900™

    Liko OctoStretch™

  • www.l iko.com

    © C

    opyr

    ight

    Lik

    o A

    B 2

    013-

    01

    Liko AB Nedre vägen 100SE-975 92 Luleå[email protected]