cad manual
DESCRIPTION
A Manual on CADTRANSCRIPT
![Page 1: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/1.jpg)
CREATION OF SIMPLE BLLOCK
AIM: creation of simple block by using the commands of circle, point, trim, mirror, etc
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model.
Command: lineSpecify first point: 110,50Specify next point or [Undo]: 260,50Specify next point or [Undo]: 260,180Specify next point or [Close/Undo]: 110,180Specify next point or [Close/Undo]: close
Command: pointSpecify the point :185,180
Command: _circle Specify center point for circle or [3P/2P/Ttr (tan tan /radius)]: 185,180Specify radius of circle or [Diameter]: 35
Command: arcSpecify start point of arc or [Center]: ceSpecify center point of arc: @45<0Specify end point of arc or [Angle/chord Length]: ASpecify included angle: 180
Command :TrimSelect the object: pick the source objectSelect the object to trim : trim unwanted line
Command: lineSpecify first point: 135,125Specify next point or [Undo]: 235,135 ENTER
![Page 2: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/2.jpg)
![Page 3: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/3.jpg)
Command :pointSpecify the point:235,95
Command: arcSpecify start point of arc or [Center]: ceSpecify center point of arc: (pick the start point )(110,50)Specify end point of arc or [Angle/chord Length]: (pick the end point )(235,125)
Command:mirrorSelect the object: pick the arcSpecify first point of mirror line: pick the mid point of line 1Specify next point of mirror line: pick the mid point of line2 Delete the source objects:{yes/no}:no ENTER
RESULT:Thus the Simple Block Drawing Was Created Successfully Using Auto Cad
Software
![Page 4: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/4.jpg)
CREATION OF RECTANGLE
Aim : To create a rectangle using Auto CAD Software.
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model.
Command: lineSpecify first point: 110,50Specify next point or [Undo]: 260,50Specify next point or [Undo]: 260,180Specify next point or [Close/Undo]: 110,180Specify next point or [Close/Undo]: close
RESULT:Thus the rectangle Drawing Was Created Successfully Using Auto Cad
Software
![Page 5: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/5.jpg)
![Page 6: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/6.jpg)
CREATION OF CONE
Aim : To create front view and top view of cone using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model.
FRONT VIEW:
Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: 50Specify next point or [Undo]: @75<108Specify next point or [Close/Undo]: close
TOP VIEW
Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] <35.0000>: DSpecify diameter of circle <70.0000>: 50 ENTER
RESULT:Thus the cone Drawing Was Created Successfully Using Auto Cad Software
![Page 7: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/7.jpg)
![Page 8: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/8.jpg)
CREATION OF CYLINDER
Aim : To create front view and top view of cylinder using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model.
FRONT VIEW:
Command: LINESpecify first point: pick any pointSpecify next point or [Undo]: 40Specify next point or [Undo]: 75Specify next point or [Close/Undo]: close
TOP VIEW
Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] <35.0000>: DSpecify diameter of circle <70.0000>: 40 ENTER
RESULT:Thus the front view and top view of a cylinder Drawing Was Created
Successfully Using Auto Cad Software
![Page 9: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/9.jpg)
CREATION OF HEXAGONAL PRISM
Aim : To draw the front view and top view of hexagonal prism height of 70 mm and edge 35 mm using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
FRONT VIEW:
Command: LINESpecify first point: pick the point with respect to (a)Specify next point or [Undo]: point with respect to (b)Specify next point or [Undo]: 70Specify next point or [Undo]: 70Specify next point or [Close/Undo]: close
TOP VIEW
Command: polygonEnter number of sides <4>: 6Specify center of polygon or [Edge]: eSpecify first endpoint of edge: Specify second endpoint of edge: 35 enter
RESULT:Thus the front view and top view of a hexagonal prism Drawing Was
Created Successfully Using Auto Cad Software
![Page 10: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/10.jpg)
![Page 11: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/11.jpg)
CREATION OF PENTAGONAL PRISM
Aim : To draw the front view and top view of pentagonal prism height of 70 mm and edge 35 mm using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000, 0.0000>: 0,0Specify upper right corner <12.0000, 9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
FRONT VIEW:
Command: LineSpecify first point: pick the point with respect to (a)Specify next point or [Undo]: point with respect to (b)Specify next point or [Undo]: 70Specify next point or [Undo]: 70Specify next point or [Close/Undo]: close
TOP VIEW
Command: PolygonEnter number of sides <4>: 5Specify center of polygon or [Edge]: eSpecify first endpoint of edge: Specify second endpoint of edge: 35 enter
RESULT:Thus the front view and top view of pentagonal prism Drawing Was Created
Successfully Using Auto Cad Software
![Page 12: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/12.jpg)
CREATION OF TITLE BLOCK
Aim : To draw the following title block with necessary text and projection symbol using Auto CAD Software.
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 500,500
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: LINESpecify first point: 100,150Specify next point or [Undo]: @230,0Specify next point or [Undo]: @0,130Specify next point or [Close/Undo]: @-230,0Specify next point or [Close/Undo]: close
Command: OffsetSpecify offset distance or [Through] <25.0000>: 25Select object to offset or <exit>: LINE 1Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER
Command: LINESpecify first point: 190,125Specify next point or [Undo]: @0,45Specify next point or [Undo]: @140,0 ENTER
Command: OffsetSpecify offset distance or [Through] <25.0000>: 15Select object to offset or <exit>: LINE 2Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LINE 3Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LINE 3Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LAST CRAEATED LINE ENTER
![Page 13: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/13.jpg)
Command: LINESpecify first point: 190,170Specify next point or [Undo]: @0,60 ENTER
Command: OffsetSpecify offset distance or [Through] <25.0000>: 15Select object to offset or <exit>: LINE ASpecify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LAST CREATED LINE Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: LAST CREATED LINE Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER
Command: OffsetSpecify offset distance or [Through] <25.0000>: 20Select object to offset or <exit>: LINE BSpecify point on side to offset: →RIGHT PSIDESelect object to offset or <exit>: ENTER
Command: OffsetSpecify offset distance or [Through] <25.0000>: 50 Select object to offset or <exit>: LAST CREATED LINESpecify point on side to offset: →RIGHT PSIDESelect object to offset or <exit>: ENTER
Command: OffsetSpecify offset distance or [Through] <25.0000>: 35Select object to offset or <exit>: LAST CREATED LINESpecify point on side to offset: →RIGHT SIDESelect object to offset or <exit>: LAST CREATED LINESpecify point on side to offset: →RIGHT SIDESelect object to offset or <exit>: ENTER
CREATING THE TEXT Command: TextCurrent text style: "Standard" Text height: 0.2000Specify start point of text or [Justify/Style]: 105,118Specify height <0.2000>: 3.5Specify rotation angle of text <0>: 0Enter text: TITLE
![Page 14: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/14.jpg)
![Page 15: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/15.jpg)
Command: TextCurrent text style: "Standard” Text height: 0.2000Specify start point of text or [Justify/Style]: 115,105Specify height <0.2000>: 7.5Specify rotation angle of text <0>: 0Enter text: LAYOUT
Command: TextCurrent text style: "Standard” Text height: 0.2000Specify start point of text or [Justify/Style]: 225,105Specify height <0.2000>: 7.5Specify rotation angle of text <0>: 0Enter text: NAME
CREATING THE PROJECTION SYMBOL
Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]: 235,147.5Specify radius of circle or [Diameter] <25.0000>: DSpecify diameter of circle <50.0000>: 30
Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]: 235,147.5Specify radius of circle or [Diameter] <15.0000>: DSpecify diameter of circle <30.0000>: 15 ENTER
Command: LINESpecify first point: 260,162.5Specify next point or [Undo]: @0,-30Specify next point or [Undo]: @40,7.5Specify next point or [Close/Undo]: @0,15Specify next point or [Close/Undo]: @-40,7.54Specify next point or [Close/Undo]: Close
RESULT:Thus the following title block drawing was created successfully using
Auto Cad Software.
![Page 16: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/16.jpg)
CREATION OF 3D MODEL OF V BLOCK
AIM: To draw the 3d view of v block using Auto CAD Software
Command: vpointSpecify a view point or [Rotate] <display compass and tripod>: 1,-1,1Regenerating model.
Command: shademodeEnter option [2D wireframe/3D wireframe/Hidden/Flat/Gouraud/fLat+edges/gOuraud+edges] <Flat+Edges>: 3d
Command: lineSpecify first point :pick any point Specify next point or [Undo]: @30,0,0Specify next point or [Undo]: @0,0,20Specify next point or [Close/Undo]: @-5,0,0Specify next point or [Close/Undo]: @-10,0,-10Specify next point or [Close/Undo]: @-10,0,10Specify next point or [Close/Undo]: @-5,0,0Specify next point or [Close/Undo]: c
Command: regionSelect objects: Specify opposite corner: 6 foundSelect objects:1 loop extracted.1 Region created.
Command: extEXTRUDESelect objects: select objectSpecify height of extrusion or [Path]: 30Specify angle of taper for extrusion <0>: 0 ENTER
RESULT: Thus the 3D view of V block drawing was successfully created using
Auto CAD Software
![Page 17: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/17.jpg)
![Page 18: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/18.jpg)
CREATION OF 3D MODEL OF BASE OF MIXEE
AIM: To draw the 3d view of base of mixee using Auto CAD Software
Command: vpointSpecify a view point or [Rotate] <display compass and tripod>: 1,-1,1Regenerating model.
Command: shademodeEnter option [2D wireframe/3D wireframe/Hidden/Flat/Gouraud/fLat+edges/gOuraud+edges] <Flat+Edges>: 3d
Command: lineSpecify first point :pick any point Specify next point or [Undo]: @0,95,0Specify next point or [Undo]: @0,-10,65Specify next point or [Close/Undo]: @0,-30,0Specify next point or [Close/Undo]: @0,-15,-45Specify next point or [Close/Undo]: @0,-30,0Specify next point or [Close/Undo]: c
Command: regionSelect objects: Specify opposite corner: 6 foundSelect objects: all objects1 loop extracted.1 Region created
Command: ext EXTRUDESelect objects: select objectSpecify height of extrusion or [Path]: 40Specify angle of taper for extrusion <0>: 0 ENTER
Command: CircleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] : DSpecify diameter of circle <70.0000>: 15 ENTER
![Page 19: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/19.jpg)
Command: extEXTRUDESelect objects: select objectSpecify height of extrusion or [Path]: 20 Specify angle of taper for extrusion <0>: 0 ENTER
Command: SubtractSelect objects: select the objectSelect objects: pick the circleSelect objects: select the object
RESULT: Thus the 3D view of base of mixee drawing was successfully created using
Auto CAD Software.
![Page 20: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/20.jpg)
![Page 21: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/21.jpg)
CREATION OF CUBIC SPLINE
AIM: To draw the cubic spline using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: PLINESpecify start point: @10,0Current line-width is 0.0000Specify next point or [Arc/Halfwidth/Length/Undo/Width]: @0,10Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-20,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-20Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-20Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @30,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,30Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-40,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-40Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @50,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,50Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-60,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @60,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-60Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @70,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,70Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-80,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-80Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @90,0Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: ENTER
RESULT:Thus the cubic spline drawing was successfully created using
Auto CAD Software.
![Page 22: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/22.jpg)
![Page 23: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/23.jpg)
CREATION OF PARABOLA
AIM: To draw the parabola using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: SPLINESpecify first point or [Object]: pick any point p1Specify next point : pick any point p2Specify next point or [Close/Fit tolerance]: pick any point p3Specify next point or [Close/Fit tolerance] : ENTERSpecify start tangent: ENTERSpecify end tangent: ENTER
RESULT: Thus the cubic spline drawing was successfully created using
Auto CAD Software
![Page 24: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/24.jpg)
![Page 25: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/25.jpg)
ISOMETRIC DRAWING
AIM: To Draw the Isometric Drawing Using Auto CAD Software
Command: snapSpecify snap spacing or [ON/OFF/Aspect/Rotate/Style/Type] <0.5000>: styleEnter snap grid style [Standard/Isometric] <S>: isometricSpecify vertical spacing <0.5000>: ENTER
Command: lineSpecify first point:Specify next point or [Undo]: 90Specify next point or [Undo]: 120Specify next point or [Close/Undo]: 70Specify next point or [Close/Undo]: 20Specify next point or [Close/Undo]: 90Specify next point or [Close/Undo]: 120Specify next point or [Close/Undo]: 70Specify next point or [Close/Undo]: close
Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 60
Command: copySelect the object: select the lineSpecify base of displacement: pick the point ENTER
RESULT:Thus the isometric object drawing was successfully created using
Auto CAD Software
![Page 26: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/26.jpg)
![Page 27: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/27.jpg)
3D VIEW OF CONE
AIM: To draw the 3d view of cone using Auto CAD Software
Command: vpointSpecify a view point or [Rotate] <display compass and tripod>: 1,-1,1Regenerating model.
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: shademodeEnter option [2D wireframe/3D wireframe/Hidden/Flat/Gouraud/fLat+edges/gOuraud+edges] <Flat+Edges>: 3d
Command: coneSpecify center point for base of cone or [Elliptical] <0,0,0>: pick any pointSpecify radius for base of cone or [Diameter]: 50Specify height of cone or [Apex]: 70 ENTER
RESULT:Thus the 3D view of cone drawing was successfully created using
Auto CAD Software
![Page 28: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/28.jpg)
![Page 29: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/29.jpg)
3D VIEW OF CYLINDER
AIM: To draw the 3d view of cylinder using Auto CAD Software
Command: vpointSpecify a view point or [Rotate] <display compass and tripod>: 1,-1,1Regenerating model.
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: shademodeEnter option [2D wireframe/3D wireframe/Hidden/Flat/Gouraud/fLat+edges/gOuraud+edges] <Flat+Edges>: 3d
Command: coneSpecify center point for base of cone or [Elliptical] <0,0,0>: pick any pointSpecify radius for base of cone or [Diameter]: 30Specify height of cone or [Apex]: 100 ENTER
RESULT:Thus the 3D view of cylinder drawing was successfully created using
Auto CAD Software
![Page 30: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/30.jpg)
![Page 31: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/31.jpg)
3D VIEW OF HEXAGONAL PRISM
AIM: To draw the 3d view of hexagonal prism using Auto CAD Software
Command: vpointSpecify a view point or [Rotate] <display compass and tripod>: 1,-1,1Regenerating model.
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: shademodeEnter option [2D wireframe/3D wireframe/Hidden/Flat/Gouraud/fLat+edges/gOuraud+edges] <Flat+Edges>: 3d
Command: polygonEnter number of sides <4>: 6Specify center of polygon or [Edge]: pick any pointEnter an option: ISpecify radius of the circle: 35
Command: extEXTRUDESelect objects of extrude: select the objectSpecify height of extrusion or [Path]: 70Specify angle of taper for extrusion <0>: 0 ENTER
RESULT:Thus the 3D view of hexagonal prism drawing was successfully created
using Auto CAD Software
![Page 32: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/32.jpg)
![Page 33: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/33.jpg)
SECTIONAL VIEW OF CYLINDER
AIM: To draw the sectional view of cylinder using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: CircleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]: pick any pointSpecify radius of circle or [Diameter] : DSpecify diameter of circle <70.0000>: 50 ENTER
Command: LineSpecify first point: pick any point with respect to circleSpecify next point or [Undo]: @50<0Specify next point or [Undo]: @70<90Specify next point or [Close/Undo]: @50<180Specify next point or [Close/Undo]: Close
Command: OffsetSpecify offset distance or [Through] <25.0000>:14Select object to offset or <exit>: LINE 1Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER
Command: LineSpecify first point: pick any point with respect to offset lineSpecify next point or [Undo]: both corners ENTER
Command: HatchCommand: hatchSelect internal point: pick points ENTER
RESULT:Thus the sectional view of cylinder was successfully created using Auto
CAD Software
![Page 34: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/34.jpg)
![Page 35: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/35.jpg)
SECTIONAL VIEW OF CONE
AIM: To draw the sectional view of cone using Auto CAD
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model
Command: CircleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick any pointSpecify radius of circle or [Diameter] : DSpecify diameter of circle <70.0000>: 35 ENTER
Command: LineSpecify first point: pick any point with respect to circleSpecify next point or [Undo]: @35<0Specify next point or [Undo]: @42<108Specify next point or [Close/Undo]: Close
Command: OffsetSpecify offset distance or [Through] <25.0000>:14Select object to offset or <exit>: LINE 1Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER
Command: LineSpecify first point: pick any point with respect to offset lineSpecify next point or [Undo]: both corners ENTER
Command: CircleBy using three points method find the diameter value and draw the circle
Command: HatchCommand: hatchSelect internal point: pick points ENTER
RESULT:Thus the sectional view of cylinder was successfully created using
Auto CAD Software
![Page 36: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/36.jpg)
![Page 37: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/37.jpg)
2D VIEW OF V BLOCK
AIM: To draw the 2d view of following v block (front view, top view and side
view) using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model.
FRONT VIEW
Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: @5<180Specify next point or [Undo]: @20< 270Specify next point or [Undo]: @30<0Specify next point or [Undo]: @20<90Specify next point or [Undo]: @5<180Specify next point or [Close/Undo]: Close
Command: LineSpecify first point: (SELECT END 1)Specify next point or [Undo]: @14.1<315 ENTER
Command: LineSpecify first point: (SELECT END 2)Specify next point or [Undo]: @14.1<225 ENTER
TOP VIEW
Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @30<0Specify next point or [Undo]: @30<270Specify next point or [Undo]: close
![Page 38: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/38.jpg)
![Page 39: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/39.jpg)
Command: OffsetSpecify offset distance or [Through] <25.0000>:5Select object to offset or <exit>: LINE 1Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER
Command: OffsetSpecify offset distance or [Through] <25.0000>:10Select object to offset or <exit>: LINE 2Specify point on side to offset: → RIGHT SIDESelect object to offset or <exit>: ENTER
SIDE VIEW
Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @30<0Specify next point or [Undo]: @20<90Specify next point or [Undo]: @30<180Specify next point or [Undo]: close
Command: OffsetSpecify offset distance or [Through] : 10Select object to offset or <exit>: SELECT LINE Specify point on side to offset: ↑ UPSIDESelect object to offset or <exit>: ENTER
Command: TextSpecify starting point: pick any point Specify the height: 5Type the text: front view, top view, side view
RESULT: Thus the 2D view of V block drawing was successfully created using
Auto CAD Software
![Page 40: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/40.jpg)
2D VIEW OF BASE OF MIXEEAIM:
To draw the 2d view of following v block (front view, top view and side view) using Auto CAD Software
Command: limitsReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <12.0000,9.0000>: 300,300
Command: zoom [All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: allRegenerating model.
FRONT VIEW
Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: @95<0Specify next point or [Undo]: @65< 90Specify next point or [Undo]: @10<180Specify next point or [Undo]: @30<180Specify next point or [Close/Undo]: ENTER
Command: LineSpecify first point: pick any pointSpecify next point or [Undo]: select corner 1Specify next point or [Undo]: @20< 90Specify next point or [Undo]: @10<0Specify next point or [Undo]: @30< 0 ENTER
Command: LineSpecify first point: select corner ASpecify next point or [Undo]: select corner B ENTER
Command: LineSpecify first point: select corner CSpecify next point or [Undo]: select corner D ENTER
![Page 41: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/41.jpg)
Command: EraseSpecify first point: pick any pointSpecify next point or [Undo]: Remove Unwanted LinesCommand: LineSpecify first point: select mid pointSpecify next point or [Undo]: @20<270 ENTER
Command: OffsetSpecify offset distance or [Through] :7.5Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE
Command: OffsetSpecify offset distance or [Through] :7.5Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE
Command: LineSpecify first point: select corner GSpecify next point or [Undo]: ENTER
TOP VIEW
Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @95<0Specify next point or [Undo]: @40< 270Specify next point or [Undo]: @95<180Specify next point or [Undo]: close
Command: OffsetSpecify offset distance or [Through] :10Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE
Command: OffsetSpecify offset distance or [Through] :30Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE
![Page 42: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/42.jpg)
![Page 43: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/43.jpg)
Command: OffsetSpecify offset distance or [Through] :10Select object to offset or <exit>: SELECT LINE Specify point on side to offset: →RIGHT SIDE
Command: OffsetSpecify offset distance or [Through] :10Select object to offset or <exit>: SELECT LINE Specify point on side to offset: ←LEFT SIDE
Command: circleSpecify center point for circle or [3P/2P/Ttr (tan tan radius)]:pick center pointSpecify radius of circle or [Diameter] <35.0000>: 75 ENTER
SIDE VIEW
Command: LineSpecify first point: pick any point with reference to front viewSpecify next point or [Undo]: @40<0Specify next point or [Undo]: @65< 90Specify next point or [Undo]: @40<180Specify next point or [Undo]: close
Command: TextSpecify starting point: pick any point Specify the height: 5Type the text: front view, top view, side view
RESULT: Thus the 2D view of base of mixee drawing was successfully created using
Auto CAD Software
![Page 44: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/44.jpg)
CREATION OF STEEL TRUSS
AIM:To create the steel truss using AutoCAD.
Command: LIMITSReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <420.0000,297.0000>: 500,500
Command: ZOOMSpecify corner of window, enter a scale factor (nX or nXP), or[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: ALLRegenerating model.
To draw B1Command: lineSpecify first point:Specify next point or [Undo]: 320Specify next point or [Undo]: 5Specify next point or [Close/Undo]: close
To draw C1Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 3Specify next point or [Undo]: 65Specify next point or [Undo]: 3Specify next point or [Undo]: 65Specify next point or [Close/Undo]: close
To draw C2Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 3Specify next point or [Undo]: 50Specify next point or [Undo]: 3Specify next point or [Undo]: 50Specify next point or [Close/Undo]: close
![Page 45: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/45.jpg)
To draw C3Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 3Specify next point or [Undo]: 32Specify next point or [Undo]: 3Specify next point or [Undo]: 32Specify next point or [Close/Undo]: close
To draw C4Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 3Specify next point or [Undo]: 15Specify next point or [Undo]: 3Specify next point or [Undo]: 15Specify next point or [Close/Undo]: close
To draw T1Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 182Specify next point or [Undo]: 3Specify next point or [Undo]: 182Specify next point or [Undo]: 3Specify next point or [Close/Undo]: close
Command: rotateSelect objects: select T1Specify base point: pick the point CSpecify rotation angle or [Reference]: 18Specify next point or [Close/Undo]: close
To draw S1Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 66Specify next point or [Undo]: 3Specify next point or [Undo]: 66Specify next point or [Undo]: 3Specify next point or [Close/Undo]: close
![Page 46: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/46.jpg)
Command: rotateSelect objects: select S1Specify base point: pick right sideSpecify rotation angle or [Reference]: - 46Specify next point or [Close/Undo]: close
To draw S2Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 60Specify next point or [Undo]: 3Specify next point or [Undo]: 60Specify next point or [Undo]: 3Specify next point or [Close/Undo]: close
Command: rotateSelect objects: select S2Specify base point: pick right sideSpecify rotation angle or [Reference]: - 31Specify next point or [Close/Undo]: close
To draw S3Command: lineSpecify first point: pick any pointSpecify next point or [Undo]: 54Specify next point or [Undo]: 3Specify next point or [Undo]: 54Specify next point or [Undo]: 3Specify next point or [Close/Undo]: close
Command: rotateSelect objects: select S3Specify base point: pick right sideSpecify rotation angle or [Reference]: - 14Specify next point or [Close/Undo]: close
To connect C1 to B1Command: C1 to B1Select object: C1Specify base point: C1(corner point)Specify second point: B1(point)
![Page 47: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/47.jpg)
![Page 48: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/48.jpg)
To connect T1 to C1Command: moveSelect object: C1Specify base point: T1(corner point)Specify second point: C1(corner point)Mirroring the object
Command: mirrorSelect objects: select allSpecify first point of mirror line: select line (point)Specify second point of mirror line: select line (point)Delete source objects? [Yes/No] <N>: no
RESULT:Thus the steel truss is perfectly created using AutoCAD software.
![Page 49: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/49.jpg)
RESIDENTIAL BUILDING PLAN
AIM:To create the plane of residential building plan using AutoCAD.
Command: LIMITSReset Model space limits:Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0Specify upper right corner <420.0000,297.0000>: 500,500
Command: ZOOMSpecify corner of window, enter a scale factor (nX or nXP), or[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: ALLRegenerating model.
Command: lineSpecify first point: @60,150Specify next point: @90,0Specify next point: @0,-110Specify next point: @-46,0Specify next point: @-30,0Specify next point: @-14,10Specify next point or [Close/Undo]: close
Command: lineSpecify first point: @61,149Specify next point: @88,0Specify next point: @0,-108Specify next point: @-44,0Specify next point: @-28,0Specify next point: @-0,8Specify next point or [Close/Undo]: close
To draw W-C blockCommand: lineSpecify first point: @63,147Specify next point: @12,0Specify next point: @0,-10Specify next point: @-12,0Specify next point or [Close/Undo]: close
![Page 50: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/50.jpg)
To draw both blockCommand: lineSpecify first point: @63,136Specify next point: @12,0Specify next point: @0,-18Specify next point: @-12,0Specify next point or [Close/Undo]: close
To draw passage blockCommand: lineSpecify first point: @77,147Specify next point: @38,0Specify next point: @0,-28Specify next point: @-38,0Specify next point or [Close/Undo]: close
To draw kitchen blockCommand: lineSpecify first point: @147,147Specify next point: @0,-2Specify next point: @-31,0Specify next point: @-12,0Specify next point or [Close/Undo]: close
To draw living room blockCommand: lineSpecify first point: @63,116Specify next point: @42,0Specify next point: @0,-58Specify next point: @-42,0Specify next point or [Close/Undo]: close
To draw the windows-ICommand: lineSpecify first point: @63,64Specify next point: @-9,0Specify next point: @0,15Specify next point: @9,0Specify next point or [Close/Undo]: close
![Page 51: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/51.jpg)
![Page 52: Cad Manual](https://reader036.vdocuments.site/reader036/viewer/2022062519/5695cf441a28ab9b028d55fe/html5/thumbnails/52.jpg)
To draw the windows-IICommand: lineSpecify first point: @126,147Specify next point: @0,9Specify next point: @12,0Specify next point: @9,0Specify next point or [Close/Undo]: close
RESULT:Thus the plane of the residential building is successfully created using
AutoCAD software.