cable glands catalogue - triflex manufacturing · the sealsafe range of metal cable glands are your...

Cable Glands Catalogue

The Sealsafe range of metal cable glands are your guarantee of safety

in hazardous locations especially where fi re and explosion are an identifi ed risk.

The current Sealsafe range is quite simply the best available because

they do not compromise on safety – and that’s what counts!

Take a look at just some of the features that make Sealsafe the fi rst choice:

Highly durable nickel platingSealsafe glands are coated in a proprietary 2 coat plating process that ensures all metal

components will not degrade and potentially let you down over time.

Comprehensive RangeThe greater the range of cable sizes a gland is designed to cover, the higher the risk of seals

failing. Sealsafe contains a comprehensive range with smaller cable acceptance increments

that also allows the gland bodies to be smaller and hence easier to use when space is tight.

Full ApprovalsDon’t just take our word for it, independent test bodies have confi rmed that the Sealsafe gland

range complies with relevant standards.

Neoprene SealsAll Sealsafe glands use high quality Neoprene seals that retain their tension and are resistant to oil,

chemicals and fl ame making them the best choice for hazardous applications.

IP66/68 ProtectionAll Sealsafe glands classifi ed for indoor/outdoor use are supplied with IP66/68 gaskets for

installation on the mounting thread and neoprene seals on the cable sheath. This level

of protection means that the glands are protected from the ingress of dust and water.

Anything less is unacceptable and compromises safety.

O’Ring SealsAll Sealsafe glands designed for SWA cable and classifi ed for indoor/outdoor use, feature o’ring

seals between the body and sleeve to ensure that water cannot progress along the thread

and compromise the seal. Just another safety feature.

Easy to useThe ability to easily produce a tight seal and correct earth everytime is of primary importance.

All Sealsafe glands are designed to be easy to use and to ensure that the installer can see that

the correct fi tting instructions have been followed. For example, all SWA fl ameproof glands

feature a loose clamping cone so that the installer can see that the armour is fully secured.

When safety matters, there is only one choice.

Introduction

2

ealsafeS

RBerg

Typewritten Text

RBerg

Typewritten Text

RBerg

Typewritten Text

RBerg

Typewritten Text

MOU

NTIN

G TH

READ

ACRO

SS C

ORNE

RS

CABL

E OV

ERAL

L

MAX

BODY

IP66/68 GASKET NEOPRENE SEAL

SKID WASHER

NUT

PROTRUSIONTHREADLENGTH

UT12AUT16AUT20AUT20BUT25AUT32AUT40AUT40BUT50AUT50BUT63AUT63B

101010101010161616161919

1.0 1.0 6.010.615.020.025.030.035.040.045.050.0

6.06.010.615.020.025.030.035.040.045.050.055.0

18.320.627.530.933.040.751.155.060.967.078.088.0

131314161718212323242532

1/2” x 26 TPI M16 x 1.5M20 x 1.5M20 x 1.5M25 x 1.5M32 x 1.5M40 x 1.5M40 x 1.5M50 x 1.5M50 x 1.5M63 x 1.5M63 x 1.5

Fitting Instructions1. To comply with IP66/68 appr bre gasket must be installed on the mounting thread.2. Screw the gland body into the apparatus, or use a locknut to secure body.3. Pass the cable through the gland to the required position and tighten gland

rmly onto the cable.

Part Mounting Thread Cable Acceptance Details Cable Gland Number Size Length Overall Diameter Across (mm) (mm) Min. Max. Corners Protrusion

(mm) (mm) (mm) (mm)

UT Cable GlandGENERAL PURPOSE CABLE GLAND FOR CIRCULAR CABLE

Product specifi cations may change at any time without notice.

3

ApplicationsIndoor and Outdoor use in hazardous areas

StandardsAS60529 - 2004

FunctionProvides Seal on Cable Sheath

Protection ClassIngress of waterIP66/68 (30m)

Construction Sealsafe Plated Brass Components

ealsafeS

RBerg

Typewritten Text

RBerg

Typewritten Text

ApplicationsIndoor use

FunctionProvides Armour Clamp

ConstructionSealsafe Plated Brass Components

Fitting Instructions1. Screw the gland body into the apparatus.2. Pass the gland sleeve over the cable before commencing to strip the outer sheath of the cable.3. Measure the length of tails required and add about 75mm to the outer sheath and armour to this point.4. Strip the outer sheath.5. Cut the armour wire to the SWA exposed length in the table.6. Pass the armour clamp over the armour.7. Pass the armour cone over the bedding and under the armour wires.8. Pass the bedding through the gland body.9. Engage sleeve thread onto body thread and tighten securely.

GT164GT204GT206GT254GT256GT324GT326GT405GT503GT505GT636GT753GT755

M16 x 1.5 M20 x 1.5M20 x 1.5M25 x 1.5M25 x 1.5M32 x 1.5M32 x 1.5M40 x 1.5M50 x 1.5M50 x 1.5M63 x 1.52.5”BSP2.5”BSP

10.0010.0010.0010.0010.0010.0010.0015.0015.0015.0019.0019.0019.00

7.2011.0013.7516.2518.7522.7526.5032.7538.5044.4556.2560.3566.70

10.8017.0020.0022.5026.0030.0034.0041.5049.0055.5068.2573.0079.40

0.90 - 1.250.90 - 1.250.90 - 1.250.90 - 1.251.25 - 1.601.25 - 1.601.60 - 2.001.60 - 2.002.00 - 2.502.00 - 2.502.50 - 3.152.50 - 3.152.50 - 3.15

20.525.227.530.333.639.544.554.260.366.782.695.3101.6

21.526.326.326.335.738.738.744.651.354.556.060.060.0

7.4010.4016.6019.6022.1025.6029.6033.6041.1048.6055.1067.8572.60

8.08.08.08.010.512.012.014.015.515.517.521.521.5

PROTRUSION

CABL

E OV

ERAL

LM

AX

ACRO

SS C

ORNE

RS

MOU

NTIN

G TH

READ

CABL

EO/

BEDD

ING

MAX

BODYSWA

EXPOSED CLAMP SLEEVE

THREADLENGTH


Part Mounting Thread Cable Acceptance Details Cable Gland Number Size Length O/bedding Overall Diameter SWA Across SWA (mm) (mm) Max. Min. Max. Dia. Corners Protrusion Exposed

(mm) (mm) (mm) (mm) (mm) (mm) (mm)

4

BODYDDSWAWW

EXPOSED CLAMP SLEEVE

GT Cable GlandGENERAL PURPOSE CABLE GLAND FOR STEEL WIRED ARMOURED CABLE

ealsafeS

RBerg

Typewritten Text

RBerg

Typewritten Text

RBerg

Typewritten Text

ApplicationsIndoor and outdoor use

FunctionProvides armour clamp, and sealon outer sheath

Protection ClassIngress of waterIP66/68


WGT Cable Gland

Part Mounting Thread Cable Acceptance Details Cable Gland Number Size Length O/bedding Overall Diameter SWA Across SWA (mm) (mm) Max. Min. Max. Dia. Corner Protrusion Exposed


MOU

NTIN

G TH

READ

CABL

EO/

BEDD

ING

MAX

CABL

E OV

ERAL

LM

AX

PROTRUSION

BODY

IP66/68 GASKETO RINGSEAL CLAMP

SWAEXPOSED

SLEEVE

NEOPRENE SEAL

NUT

ACRO

SS C

ORNE

RS

THREADLENGTH

WGT162WGT164WGT202WGT203WGT204WGT206WGT254WGT256WGT324WGT326WGT403WGT404WGT405WGT502WGT503WGT504WGT505WGT634WGT635WGT636WGT753WGT754WGT755WGT10AWGT10B

M16 x 1.5M16 x 1.5M20 x 1.5M20 x 1.5M20 x 1.5M20 x 1.5M25 x 1.5M25 x 1.5M32 x 1.5M32 x 1.5M40 x 1.5M40 x 1.5M40 x 1.5M50 x 1.5M50 x 1.5M50 x 1.5M50 x 1.5M63 x 1.5M63 x 1.5M63 x 1.52.5”BSP2.5”BSP2.5”BSP3”BSP3”BSP

14141414141414141414151515151515151919191919191919

6.007.208.009.7511.0013.7516.2518.7522.7526.5028.5030.7532.7535.7538.5041.6544.4548.8052.4056.2560.3563.5066.7070.0076.00

9.6010.8012.0015.5017.0020.0022.5026.0030.0034.0037.0039.5041.5045.0049.0053.5055.5060.3563.5068.2573.0076.2079.4084.0088.50

0.50 - 0.90 0.50 - 0.90 0.50 - 0.90 0.90 - 1.250.90 - 1.250.90 - 1.250.90 - 1.251.25 - 1.601.25 - 1.601.60 - 2.001.60 - 2.001.60 - 2.001.60 - 2.002.00 - 2.502.00 - 2.502.00 - 2.502.00 - 2.502.50 - 3.152.50 - 3.152.50 - 3.152.50 - 3.152.50 - 3.152.50 - 3.15

3.153.15

36364040404040475555595959737373737979799393939090

8899999111212131313141414141515152222222222

Fitting Instructions1. To comply with IP66/68 appr bre gasket must be installed on the mounting thread.2. Screw the gland body into the apparatus.3. Pass the gland nut, outer seal and gland sleeve over the cable before commencing to strip the outer sheath of the cable.4. Measure the length of tails required and add about 75 mm to the outer sheath and armour to this point.5. Strip the outer sheath.6. Cut the armour wire to SWA exposed length.

7. Pass the armour clamp over the armour.8. Pass the body and armour cone over the bedding and under the armour wires.9. Engage sleeve thread onto body thread and tighten securely.10. Slide outer seal and gland nut into position and engage nut thread onto sleeve thread.11. Tighten gland nut securely.

8.009.2010.4011.6015.1016.6019.6022.1025.6029.6033.6036.6039.1041.1044.6048.6053.1055.1059.9563.1067.8572.6075.8079.0083.60

24.124.125.327.527.533.036.440.749.849.860.960.960.976.076.086.586.5101.9101.9101.9115.6115.6115.6124.0124.0

GENERAL PURPOSE CABLE GLAND FOR STEEL WIRED ARMOURED CABLE


5

ealsafeS

INNER NEOPRENESEAL

SWAEXPOSED

BODY

IP66/68 GASKETO RINGSEAL

CLAMP

CONESLEEVE

NUTOUTER NEOPRENE SEAL

PROTRUSION

ACRO

SS C

ORNE

RS

MOU

NTIN

G TH

READ

CABL

E OV

ERAL

LM

AX

CABL

EO/

BEDD

ING

MAX

THREADLENGTH

9. Pass the armour cone over the bedding and under the armour wires.10. Pass the bedding through the inner seal in the gland body. N.B. Unless this seal pr t on the bedding the next size gland will be required. (The minimum dimension over the bedding is embossed on the sleeve of the gland for reference.) On glands over FLWT405 one or two seals are supplied with each gland, select the most suitable seal.11. Engage sleeve thread onto body thread and tighten securely.12. Slide outer seal and gland nut into position and engage nut thread onto sleeve thread.13. Tighten gland nut securely.

FLWT Cable Gland


StandardsIEC 60079 - 0:2004

IEC 60079 - 1:2007IEC 61241 - 0:2004 IEC 61241 - 1:2004

Function Provides O/Bledding Flameproof Seal, ArmourClamp and Seal on Outer Sheath

Protection ClassANZEx 11.2001X

Ingress of waterIP66/68 (30m)


Fitting Instructions1. To comply with IP66/68 appr bre gasket must be installed on the mounting thread.2. Screw the gland body into the apparatus.3. Leave the inner seal in the gland body.4. Pass the gland nut, outer seal and gland sleeve over the cable before commencing to strip the outer sheath of the cable.5. Measure the length of tails required and add about 75 mm to the outer sheath and armour to this point.6. Strip the outer sheath.7. Cut the armour wire to SWA exposed length.8. Pass the armour clamp over the armour.

FLAMEPROOF CABLE GLAND FOR STEEL WIRE ARMOURED CABLE


Part Mounting Thread Cable Acceptance Details Cable Gland Inner Number Size Length Overbedding Overall Diameter SWA Across SWA Carton (mm) (mm) Min. Max. Min. Max. Dia. Corners Protrusion Exposed Pack

(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) Qty.

FLWT202 M20 x 1.5 15.80 6.00 8.00 10.00 12.00 0.50 - 0.90 25 54 12 30FLWT203 M20 x 1.5 15.80 8.30 9.75 11.60 15.50 0.90 - 1.25 27 54 12 30FLWT204 M20 x 1.5 15.80 9.35 11.00 15.10 17.00 0.90 - 1.25 27 54 12 30FLWT205 M20 x 1.5 15.80 10.60 12.50 16.60 20.00 0.90 - 1.25 33 54 12 20FLWT206 M20 x 1.5 15.80 12.00 13.75 16.60 20.00 0.90 - 1.25 33 54 12 20FLWT253 M25 x 1.5 19.00 13.35 15.00 19.60 22.50 0.90 - 1.25 36 56 12 14FLWT254 M25 x 1.5 19.00 14.60 16.25 19.60 22.50 0.90 - 1.25 36 56 12 14FLWT255 M25 x 1.5 19.00 15.85 17.50 22.10 26.00 1.25 - 1.60 41 56 12 12FLWT256 M25 x 1.5 19.00 17.10 18.75 22.10 26.00 1.25 - 1.60 41 56 12 12FLWT323 M32 x 1.5 25.40 18.35 20.75 25.60 30.00 1.25 - 1.60 50 64 13 8FLWT324 M32 x 1.5 25.40 20.35 22.75 25.60 30.00 1.25 - 1.60 50 64 13 8FLWT325 M32 x 1.5 25.40 22.35 24.75 29.60 34.00 1.60 - 2.00 50 64 13 8FLWT326 M32 x 1.5 25.40 24.35 26.50 29.60 34.00 1.60 - 2.00 50 64 13 8FLWT403 M40 x 1.5 25.40 26.10 28.50 33.60 37.00 1.60 - 2.00 61 72 15 1FLWT404 M40 x 1.5 25.40 28.10 30.75 36.60 39.50 1.60 - 2.00 61 72 15 1FLWT405 M40 x 1.5 25.40 30.35 32.75 39.10 41.50 1.60 - 2.00 61 72 15 1

6

IECEx SIM 11.0002X Ex d I/IIC

ealsafeS

RBerg

Typewritten Text

Part Mounting Thread Cable Acceptance Details Cable Gland Number Size Length O/bedding Overall Diameter SWA Across SWA (mm) (mm) Max. Min. Max. Dia. Corners Protrusion Exposed


Fitting Instructions1. To comply with IP66/68 appr bre gasket must be installed on the mounting thread.2. Pass Nut, Seal and Sleeve over the outer sheath of cable (Where more than 1 seal is supplied, use the seal with the smallest clearance on the cable).3. Measure the length of cores required and strip the outer sheath and armour wires to the length shown in Table 1.

llers to the length shown in Table 2.5. Slide the clamp over the armour wires and work the Cone over the bedding and under the SWA.6. Locate the Body onto the Cores and hold hard against the face of the Cone. Screw the Sleeve onto the Body and tighten, now tighten the nut onto the sleeve.7. Remove the Body from the assembly.8. Prepare the epoxy putty. This is a 2 part pack and must be mixed in a ratio of 1 to 1 until the colour is even throughout, without any streaks. After mixing it remains pliable for at least 1 hour. (see Useable Life for Mixed Epoxy below)

Note: The Red Epoxy component is affected by storage temperature. Please check to ensure this component is as pliable as the yellow component. It is recommended that the

tted only with the user wearing the disposable gloves supplied with every gland.9. Spread the conductors and apply to epoxy to the EXPOSED CENTRE of the conductors. Close the conductors and pack putty into the recess of the cone and down onto the top of the bedding

ll the sleeve cup.


Standards

FunctionProvides Barrier Epoxy Seal to Cable Cores,Armour Clamp, and Seal on Outer Sheath

Protection Class

Ingress of waterIP66/68 (30m)


FLPWB Cable Gland

FLPW203BFLPW206BFLPW256BFLPW326BFLPW405BFLPW503BFLPW505BFLPW635BFLPW636BFLPW754BFLPW755B

M20 x 1.5M20 x 1.5M25 x 1.5M32 x 1.5M40 x 1.5M50 x 1.5M50 x 1.5M63 x 1.5M63 x 1.5

2.5”BSP2.5”BSP

15.8015.8019.0025.4025.4028.6028.6028.6028.6028.6028.60

9.7513.7518.7526.5032.7538.5044.4552.4056.2563.5066.70

15.5020.0026.0034.0041.5049.0055.5063.5068.2576.2079.40

0.90 - 1.25 0.90 - 1.251.25 - 1.601.60 - 2.001.60 - 2.002.00 - 2.502.00 - 2.502.50 - 3.152.50 - 3.152.50 - 3.152.50 - 3.15

27334150617687102102116116

545456647288889696100100

11.6015.1019.6025.6033.6041.1048.6055.1063.1067.8575.80

11.511.511.513.515.5171719192323

MOU

NTIN

G TH

READ

CABL

EO/

BEDD

ING

MAX

EPOXY

PROTRUSION

CABL

E OV

ERAL

LM

AXAC

ROSS

COR

NERS

CLAMPSWA

EXPOSEDSLEEVE

NUTOUTER NEOPRENE SEALCONE

BODY SLEEVEO RINGSEAL

IP66/68 GASKETBODY

THREADLENGTH

Continue folding putty round the conductors and working it well in between them, joining with that extruded from the core center avoiding any gaps or voids. Cover the conductors from the face of the cone to the length equal at least to the length of the Sleeve.

ts into the Cone. Remove any surplus epoxy.11. Reassemble the Body, tighten and allow at least three hours for the epoxy to reach correct hardness.12. Remove the Body t to the equipment the r tting.

2ELBAT1ELBATGland mm

FLPW203BFLPW206BFLPW256BFLPW326BFLPW405BFLPW503BFLPW505BFLPW635BFLPW636BFLPW754BFLPW755B

11.5011.5011.5013.5015.5017.0017.0019.0019.0023.0023.00

Gland mmFLPW203BFLPW206BFLPW256BFLPW326BFLPW405BFLPW503BFLPW505BFLPW635BFLPW636BFLPW754BFLPW755B

13.5013.5013.5015.5017.5017.5019.5021.0021.0025.0025.00

Useable Life for Mixed EpoxyThis will depend upon the bulk mass and temperature. 25 grams wt 2 hours @ 25deg. CAppr gures are: 25 grams wt 3 hours @ 15deg. CCureThis will depend upon the bulk mass and temperature. 25 grams wt 12 hours @ 25deg. CAppr gures are: 25 grams wt 24 hours @ 15deg. CMechanical properties of cured mixTensile strength BS6319 2 days min. 30MPaCompressive strength BS6319 2 days min. 40MPa

Derohs57nimssendraH c Gravity @ 20 deg. C 1.84 to 1.99

BARRIER CABLE GLAND FOR STEEL WIRE ARMOURED CABLE


7

IEC 60079 - 0:2004 IEC 60079 - 1:2007IEC 61241 - 0:2004 IEC 61241 - 1:2004

ANZEx 11.2001X IECEx SIM 11.0002X Ex d I/IIC

ealsafeS

RBerg

Typewritten Text

RBerg

Typewritten Text

RBerg

Typewritten Text

ApplicationsIndoor and outdoor use in harsh environments

StandardsAS 1939 - 1990

FunctionProvides seal on cable sheath

Protection ClassIP65

ConstructionBody and compression nut304 Stainless Steel

SSG Cable GlandGENERAL PURPOSE STAINLESS STEEL CABLE GLANDS

Triflex Stainless Steel Cable Glands

are high quality glands designed

for use in severe environments. Made

from 304 grade stainless steel, each

gland features a wide cable diameter

range and UP65 protection.

8.411.516.321

27.7

3.56.4111519

M16x1.5M20x1.5M20x1.5M25x1.5M32x1.5

Part Mounting Cable Acceptance Number Thread Details Across Size Length Overall Diameter Corners (mm) (mm) Min (mm) Max (mm) (mm)

CG01S 1010121212

2222

27.53240

MOU

NTIN

G TH

READ

ACRO

SS C

ORNE

RS

CABL

E OV

ERAL

L

MAX

BODY

SEAL

SKID WASHER

NUT

PROTRUSIONTHREADLENGTH

Prod

uct

spec

ifi ca

tions

may

cha

nge

at a

ny t

ime

with

out

notic

e.

8

CG02SCG03SCG04SCG05S

Triflex Nylon Cable Glands are quick & easy to install with a high quality gripping claw/seal arrangement that caters

for a wide range of cable sizes per fi tting. Each gland has no loose parts and requires no disassembly for cable installation.

LOCKNUT WASHER BODY CLAW SEALS NUT

ACRO

SS C

ORNE

RS

CABL

EOV

ERAL

LM

AX

MOU

NTIN

GTH

READ

THREADLENGTH

TG Cable GlandGENERAL PURPOSE NYLON CABLE GLANDS

The Sealsafe range of cable glands consists of general purpose TG Nylon range through to 304 Stainless steelmodels designed to deliver superior performance in harsh environments.

ApplicationsIndoor and outdoor use

StandardsAS60529 - 2004

FunctionProvides seal on cable sheath

Protection ClassIP68, Resistant to salt water, weak alcohol, oil, grease and common solvents

ConstructionBody - UL approved Nylon 66 (Black)Seal - EPDM Rubber

Thread TypeMetric with locknut and IP68 washer

Part Mounting Thread Cable Acceptance Details Number Size Length Overall Diameter Across (mm) (mm) Min. Max. Corners

(mm) (mm) (mm)

152227273341506275

TG-12TG-16TG-20TG-20-2.5TPSTG-25TG-32TG-40TG-50TG-63

151515151515152020

4 6

8.52.5mm TPS

12.518243040

71014

N/A1825324151

M12 x 1.5 M16 x 1.5M20 x 1.5M20 x 1.5M25 x 1.5M32 x 1.5M40 x 1.5M50 x 1.5M63 x 1.5


9

RBerg

Typewritten Text

RBerg

Typewritten Text

Triflex Manufacturing Pty Ltd

29/2-4 Picrite Close

Pemulwuy, NSW 2145 Australia

Telephone: (02) 9631-5977

Email: [email protected]

cable glands catalogue - triflex manufacturing · the sealsafe range of metal cable glands are your...

Documents