cabinet types and their installation

1

HUAWEI TECHNOLOGIES Co., Ltd. HUAWEI Confidential

May 23, 2006 For Internal Use Only

Cabinet Types and Their InstallationFor GTS Engineering Center

From Integrated Equipment Engineering Dept., Liu Changlin and Deng Shunqing

2


ContentsContentsIntroduction to cabinet types1. B style cabinet2. N610 cabinet

……….

Introduction to installation environment1. Indoor environment2. Outdoor environment

Introduction to installation forms1. Installation forms2. List of relations between installation forms, installation environment and cabinets

Installation on cement floorSupport InstallationInstallation on mounting setInstallation on poleInstallation on standInstallation of other accessories1. Installation of upper fixing pieces2. Installation of shockproof reinforcement pieces3. Installation of cabling ladder and cabling trough

3


I. Types of platform cabinets and their mapping with products:

Introduction to Cabinet TypesIntroduction to Cabinet Types

Micro BTS5

4

3

2

1

4

3

2

1

No

14

13

12

11

10

9

8

7

6

5

4

3

2

1

No.

Outdoor cabinet

Type

WCDMA BTS3812

WCDMABTS3802CWCDMABTS3812E

WCDMABTS3801CCDMA2000BTS3606

CDMA2000BTS3601CCore networkB68-21

GSM BTS3002COptical networkB63B

WCDMARRU3801COptical networkT63B

Optical networkT63

Fixed networkONU-60AOptical networkT66

Fixed networkF01D200Access networkH66

Fixed networkONU-160BFixed networkN63

WCDMABTS3812AAccess networkN66

CDMA2000 BTS3606ACore networkN68

GSM BTS3012ACore network and A&SN610

GSMBTS3006ASwitchingB style

Indoor cabinet

ProductCabinetProductCabinetType

4


Introduction to CabinetsIntroduction to Cabinets

B style cabinetB style cabinet can be a welded or assembled cabinet.

Assembled B style cabinet consists of a rack, front and rear doors (both have a left leaf and right leaf), side panels, and a top cover. The rear door is same as the front door.

Rack is assembled from upper enclosure frame, lower enclosure frame, front column and rear column with bolts.

Outer dimensions of the cabinet are 800 (W) X 550 (D) X 2100 (H). When cabinet is equipped with side doors, its width is 880.

B style cabinet

--Assembled B style cabinet

5


N610-22 cabinet

N610 cabinet falls into two categories: N610-22 cabinet and N610-18 cabinet.

N610 cabinet generally adopts the N series pattern of dense-hole door, or the N series pattern of convex-rib front door.

N610 cabinet consists of a rack, front and rear doors ((both have a left leaf and right leaf) and side panels. The rear door is same as the front door.

Rack is assembled from sheet-metal enclosure frames and sheet-metal columns.

Porosity of the front door is 31% or 50%, whichever is applicable to the product requirement for ventilation and heat dissipation.

Outer dimensions of N610-22 cabinet are 600 (W) X 1000 (D) X 2200 (H).

Outer dimensions of N610-18 cabinet are 600 (W) X 1000 (D) X 1800 (H).

N610 cabinet complies with 19” standard of IEC297, and mainly applies to A&S and Datacom product lines.

--N610 cabinetIntroduction to CabinetsIntroduction to Cabinets

6


N68-22 cabinet


N68 cabinet adopts the N series cabinet pattern, which uses convex-rib front door.

N68 cabinet consists of a rack, front and rear doors (both have a left leaf and right leaf) and side panels. The rear door is same as the front door.

Rack is assembled from sheet-metal enclosure frames and sheet-metal columns.

There are multiple types of N68 rack, for example, service rack,server rack, UMG rack and SG rack.

Outer dimensions of the N68-22 cabinet are 600 (W) X 800 (D) X 2200 (H).


N68 cabinet complies with 19” standard of IEC297, and mainly applies to NGN, Core Network and Datacom product lines.


7


N66-22 cabinet


N66 cabinet adopts the N series cabinet pattern, which uses convex-rib front door.

N66 cabinet consists of a rack, front and rear doors (both have a left leaf and right leaf) and side panels. The rear door is same as the front door.

The rack is assembled from sheet-metal enclosure frames and sheet-metal columns.



N66 cabinet complies with 19” standard of IEC297, and mainly applies to broadband access products.


8


N63-22 cabinets (back to back)

There is only one type of N63 cabinet: N63-22

N63 cabinet adopts the N series cabinet pattern, which uses convex-rib, single-leaf front door.

N63 cabinet consists of a rack, a front door and a rear door.

N63 is welded from sheet-metal enclosure frames and sheet-metal columns.


N63 cabinet complies with 19” standard of IEC297, and mainly applies to fixed network products .


9


H66-22 cabinet

H66 cabinet falls into two categories: H66-22 cabinet and H66-18 cabinet.

H66 cabinet adopts the N series cabinet pattern, which uses convex-rib front door.

H66 cabinet consists of a rack, a front door (left leaf and right leaf) and side panels.


Outer dimensions of the H66-22 cabinet are 600 (W) X 600 (D) X 2200 (H).

Outer dimensions of the H66-18 cabinet are 600 (W) X 600 (D) X 1800 (H).

H66 cabinet complies with 19” standard of IEC297, and mainly applies to broadband access products.

--H66 cabinetIntroduction to CabinetsIntroduction to Cabinets

10

HUAWEI TECHNOLOGIES Co., Ltd. HUAWEI Confidential T66-22 cabinet

T66 serial cabinets have five height specifications: 2.6 m, 2,2 m, 2.0 m, 1.8 m and 1.6 m.

T66 cabinets adopt the N series cabinet pattern, which uses convex-rib, single-leaf front door.

T66 cabinet consists of a rack, a front door, a rear door and side panels. The rear door has the same structure as the front door.


Outer dimensions of the T66 serial cabinets are 600 (W) X 600 (D) X 2200 (H).

T66 cabinets comply with ETSI standard and mainly apply to Optical Network product line.

--T66 cabinetIntroduction to CabinetsIntroduction to Cabinets

11


T63-22 cabinet

T63 serial cabinets have five height specifications: 2.6 m, 2,2 m, 2.0 m, 1.8 m and 1.6 m.

T63 cabinets adopt the N series cabinet pattern, which uses convex-rib, single-leaf front door.

T63 cabinet consists of a rack, a front door, a rear door and side panels.


Outer dimensions of the T63-22 cabinet are 600 (W) X 300 (D) X 2200 (H).


--T63 cabinetIntroduction to CabinetsIntroduction to Cabinets

12


T63B-22 cabinet

T63B serial cabinets have five height specifications: 2.6 m, 2,2 m, 2.0 m, 1.8 m and 1.6 m.

T63B cabinets adopt the N series cabinet pattern, which uses convex-rib, single-leaf front door.

T63B cabinet consists of a rack, a front door, a rear door and side panels. Rear columns are used structurally.


Outer dimensions of the T63-22 cabinet are 600 (W) X 300 (D) X 2200 (H).


--T63B cabinetIntroduction to CabinetsIntroduction to Cabinets

13

HUAWEI TECHNOLOGIES Co., Ltd. HUAWEI Confidential B63B-22 cabinet

B63B serial cabinets have five height specifications: 2.6 m, 2,2 m, 2.0 m, 1.8 m and 1.6 m.

B63B cabinets adopt the B series cabinet pattern, which has no front door.

B63B cabinet consists of a rack, , a front door, a rear door and side panels. Rear columns are used structurally.

The rack is assembled from die-casting enclosure frames and sheet-metal columns.

Outer dimensions of the B63B serial cabinets are 600 (W) X 300 (D) X 2200 (H).

B63B cabinets comply with ETSI standard and mainly apply to Optical Network product line.

--B63B cabinetIntroduction to CabinetsIntroduction to Cabinets

14


B66 cabinet with dual-leaf front door

B63 cabinet with dual-leaf front door

B63 cabinet with no door

B63/66 serial cabinets include three types: B63 cabinet, B63 cabinet with no door, B66 cabinet.

B63/B66 serial cabinets comprise a rack, a front door (left leaf and right leaf), a rear door, and side panels. Rear door of B66 cabinet is same as the front door.

The rack is assembled from die-casting enclosure frames and sectional columns, or from die-casting enclosure frames and metal-sheet columns if the cabinet has no door.

Outer dimensions of B63 cabinet are 600 (W) X 300 (D) X 2200 (H).

Outer dimensions of B66 cabinet are 600 (W) X 600 (D) X 2200 (H).

B63/66 cabinets comply with ETSI standard and mainly apply to Optical Network product line.

--B63 cabinetIntroduction to CabinetsIntroduction to Cabinets

15


B68-21 cabinet B68-22 cabinet

B68 series includes B68-21 cabinet, B68-22 cabinet, B68-18 cabinet and B68-20 cabinet.

B68-21 cabinet has a similar pattern to B style cabinet.

B68-22/18/20 cabinets have the same pattern.

B68 cabinets consists of a rack, front and rear doors (both have a left leaf and a right leaf), side panels and top cover. The rear door is same as the front door.

The rack is assembled from die-casting enclosure frames and sectional columns.

Outer dimensions of B68-21 cabinet are 600 (W) X 800 (D) X 2100 (H).

Outer dimensions of B68-22/18/20 cabinet are 600 (W) X 800 (D) X 2200/1800/2000 (H).

B610-21 cabinet is structurally same as B68-21 cabinet, and its outer dimensions are 600 (W) X 1000 (D) X 2100 (H).

--B68 cabinetIntroduction to CabinetsIntroduction to Cabinets

16


BTS3606 cabinet

BTS3606 cabinet has a front door with two overlapped ventilating plates. The front door has a single leaf.

BTS3606 cabinet consists of a rack, a front door and a rear door.

The rack is assembled from upper support frame, lower support frame, and side panels.

Outer dimensions of BTS3606 cabinet are 600 (W) X 650 (D) X 1400 (H).

BTS3606 cabinet is used for CDMA BTS.

--BTS3606 cabinetIntroduction to CabinetsIntroduction to Cabinets

17


BTS3812E cabinet

BTS3812E cabinet has a front door with two overlapped ventilating plates. The front door has a single leaf.

BTS3812E cabinet consists of a rack, a front door and a rear door.

The rack is assembled from upper support frame, lower support frame, and side panels.

Outer dimensions of BTS3812E cabinet are 600 (W) X 600 (D) X 1400 (H).

BTS3812E cabinet is used for WCDMA BTS.

--BTS3812E cabinetIntroduction to CabinetsIntroduction to Cabinets

18


BTS3006A cabinet

BTS3006A cabinet is equipped with a heat exchanger and used outdoors. Temperature control device is installed to the front door.

BTS3006A cabinet consists of a rack, a front door and a rear door.

The rack is welded from a top cover, a bottom plate and middle enclosure board.

The rack has two layers. The outer layer is welded for water-proof purpose and the inner layer is connected with bolts. Heat insulation form is filled between the layers.

Outer dimensions of BTS3006A cabinet are 900 (W) X 720 (D) X 1700 (H).

BTS3006A cabinet is used for GSM BTS.

--BTS3006A cabinetIntroduction to CabinetsIntroduction to Cabinets

19


BTS3012A cabinet

BTS3012A cabinet is equipped with a heat exchanger or air-conditioner and is used outdoors. Temperature control device is installed to the front door.



The rack has two layers. The outer layer is connected with bolts, and gap at joint is glued for water-proof purpose. The inner layer is welded. Heat insulation form is filled between the layers.


BTS3012A cabinet is used for GSM BTS.


20


BTS3606A cabinet

BTS3606A cabinet is equipped with a heat exchanger or air-conditioner and is used outdoors. Temperature control device is installed to the front door.



The rack has two layers. The outer layer is connected with bolts, and gap at joint is glued for water-proof purpose. The inner layer is welded. Heat insulation form is filled between the layers.


BTS3606A cabinet is used for CDMA BTS.


21


BTS3812A cabinet

BTS3812A cabinet is equipped with a heat exchanger and used outdoors. Temperature control device is installed to the front door.



The rack has two layers. The outer layer is welded for water-proof


BTS3812A cabinet is used for WCDMA BTS.


22


RRU3801C module

When RRU3801C needs to be installed independently, modules and plastic shell should be installed.

When installed interpedently, the RRU3801C comprises modules and plastic shell.

Outer dimensions of the RRU3801C module are 400 (W) X 565 (D) X 165 (H).

RRU3801C is an outdoor RF module.

--RRU3801C moduleIntroduction to CabinetsIntroduction to Cabinets

23


BTS3002C cabinet

Major components of the BTS3002C are four units: Main Control Unit (MCU), two Digital Radio frequency Units (DRUs) and Power Supply Unit (PSU). Each unit includes internal boards with specific functions.

External cables (including power cables) of integrated equipment connect electrical signal and are water-proof through water-proof adaptation connectors at the bottom of each unit.

Outer dimensions of BTS3002C cabinet are 460 (W) X 355 (D) X 820 (H).

The BTS3002C, integrated small BTS, can be simply mounted to wall, column or stand.

--BTS3002C cabinetIntroduction to CabinetsIntroduction to Cabinets

24


--BTS3601C cabinet

BTS3601C cabinet

BTS3601C consists of modules plus rack, which are covered by an external plastic shell.

BTS3601C cabinet comprises a rack, modules and a plastic shell.

Rack is assembled from upper support frame, lower support frame and side panels.


BTS3601Cis a CDMA2000 distributed BTS cabinet.


25


BTS3801C cabinet

--BTS3801C cabinet

BTS3801C consists of modules plus rack, which are covered by an external plastic shell




BTS3801C is a WCDMA distributed BTS cabinet.


26


BTS3802C cabinet

BTS3802C consists of modules plus rack, which are covered by an external plastic shell.




BTS3802C is a WCDMA distributed BTS cabinet.

--BTS3802C cabinetIntroduction to CabinetsIntroduction to Cabinets

27


Introduction to Installation EnvironmentIntroduction to Installation EnvironmentII. Installation environment: indoor environment, outdoor environment.

1. Indoor environmentIndoor environment mainly refers to equipment room or civil room, which can have a cement floor or antistatic floor. Indoor

environment

Cement floor Antistatic floor

28


Outdoorenvironment

Ground Roof Wall Others (iron tower)

2. Outdoor environmentOutdoor environment includes floor, roof, wall and others.

Introduction to Installation EnvironmentIntroduction to Installation Environment

29


Introduction to Installation FormsIntroduction to Installation FormsIII. Introduction to installation forms

1. Installation form varies with installation environment.Installation

form

Installation oncement floor

Supportinstallation

Installation onmounting set

Installation onstand

Installation onpole

Wallmounting

30


Roof, floor or platform

Equipment room

StandInstallation on stand6

Wall surfaceWall mounting5RRU3801C, BTS3002CBTS3601C, BTS3801CBTS3802C

Micro BTS or other small equipment

Steel post (60 mm -114 mm)Installation on pole4

BTS3006A, BTS3012ABTS3606A, BTS3812A Outdoor cabinetOutdoor cement platformInstallation on

mounting set3

Indoor antistatic floorSupport Installation 2

B style, N610 N68, N66,N63H66, T66, T63T63B, B63BB68-21, BTS3606BTS3812E, BTS3812

Indoor cabinet

Indoor cement floorInstallation on cement floor1

RemarksApplicable cabinetApplicable installation environmentInstallation

formNo.

2. Table of relations between installation forms, installation environment and cabinets

Introduction to Installation FormsIntroduction to Installation Forms

31


Installation on Cement FloorInstallation on Cement Floor

Typically, platform cabinets and BTS cabinets are installed on cement floor.We take one cabinet of each type for example to introduce the installation method.

Installation of N68 cabinet, for example, on cement floor

Installation of BTS3812 cabinet, for example, on cement floor.

32


Installation of N68 cabinet, for example, on cement floor

--Install N68 cabinet

5 Washer4 Insulating plate3 Spring washer 122 Bolt M12 701 cabinet


33


Installation of BTS3812E cabinet, for example, on cement floorBTS3812E cabinet is installed on cement floor with a push-fit base.

(5) Bolt M12 30(4) Spring washer 12

(3) Plain washer 12(2) Lower frame(1) Upper frame

--Install BTS3812E cabinetInstallation on Cement FloorInstallation on Cement Floor

34


(8) Insulation plate(7) Leveling pad(6) Fixing bolts for upper and lower frames(5) Insulation covering

(4) Plain washer(3) Spring washer 12(2) Expansion bolt M12 60(1) Lower frame

Step 1: Fix lower frames on cement floor

--Install BTS3812E cabinetInstallation on Cement FloorInstallation on Cement Floor

35


--Install BTS3812E cabinet

(4) Screw assembly M6 20(3) Panel(2) Fixing bolt for upper and lower frames(1) Cabinet

Step 2: Fix the cabinet and install the base panel.


36


Support InstallationSupport Installation

I. Introduction to support installationSupport installation means that equipment is installed in equipment room with antistatic floor. Support is used to hold cabinet so as to lay floorboard and wire cables in the equipment room.Different cabinets use different supports. Their mapping is shown in the following table:

4

5

1

2

1

1

2

1

9

Cabinet type

Borrowed for four types of cabinet Used on a large scaleT66, H66, N66S600A9

Borrowed for five types of cabinet Used on a large scaleT63, T63B, B63, B63BS300A8

Used on a large scaleN610 cabinetN10007

Borrowed for two types of cabinet Used on a large scaleN68 service cabinet/server cabinetN8006

Used on a large scaleN63 cabinetN3005

To be replaced by N610 cabinet graduallySeldom usedB610-21 cabinetP10004

To be replaced by N68 cabinet graduallySeldom usedB68-21 service cabinet/server cabinetP8003

Used on a large scaleAssembled B style cabinetP5502

Borrowed for nine types of cabinet Used on a large scaleBTS30/312/3606/3612/3806/3812/3812EA6001

RemarksStatusCabinetSupportNo.

37


Introduction to support

I. Installation of A600 support for BTS3812E cabinetII. Installation of P550 support for C&C08 cabinetIII. Installation of P800 support for B68-21 cabinetIV. Installation of N300 support for N63 cabinetV. Installation of N800 support for N68 cabinetVI. Installation of S300A support for T63 cabinetVII. Installation of S600A support for T66 cabinet


38


Introduction to support

Installation of A600 support for BTS3812E cabinetInstallation of P550 support for C&C08 cabinetInstallation of P800 support for B68-21 cabinetInstallation of N300 support for N63 cabinetInstallation of N800 support for N68 cabinetInstallation of S300A support for T63 cabinetInstallation of S600A support for T66 cabinet

--Install A600 supportSupport InstallationSupport Installation

39


(4) Installation hole(3)Lower bracket(2)Upper bracket(1) Connecting hole

Heights applicable to A600 serial supports

Customized according to floor height

(minimum height is 120 mm)IV

301-445III

231-300II

195-230I

Applicable height of antistatic floor (mm)Component

Introduction to A600 support


40


Step 1: Draw lines and make holes on the antistatic floor, and connect connecting holes of the support to those of the antistatic floor.


41


Step 2: Put the antistatic floor connected with support at the original place so as to align the support. Fix the support.

(7) Expansion bolt M12 60

(6) Height-locking bolt (middle)(5) Height-locking bolt (both sides)(4) Big plain washer Φ12

(3) Spring washer Φ12(2)Bolt M12 70(1)Antistatic floor


42


Step 3: Install lower frame of the base.


43


(5) Combination bolt M6X20(4) Panel

(3) Plain washer Φ12(2) Spring washer Φ12(1) Bolt M12x30

Step 4: Install cabinet. Align the upper and lower frames, push in the cabinet and then fix the cabinet.


44


--Install P550 supportSupport InstallationSupport Installation

Introduction to supportInstallation of A600 support for BTS3812E cabinetInstallation of P550 support for C&C08 cabinetInstallation of P800 support for B68-21 cabinetInstallation of N300 support for N63 cabinetInstallation of N800 support for N68 cabinetInstallation of S300A support for T63 cabinetInstallation of S600A support for T66 cabinet

45


End-mounted P550 support Shared P550 support

--Install P550 support

Pictorial representation of support installation


46



Support configuration: Each end of a row of cabinets needs an end-mounted support, and two adjacent cabinets share one shared support. In other words, one row of cabinets needs N+1 supports: two end-mounted supports and N-1 shared supports.

Heights applicable to P550 serial end-mounted supports and shared supports:


Customized according to floor height(minimum height is 160mm) IV

351-510III271-350II

230-270I


47



Step 1: Align the support


Expansion bolt M12

Insulation covering

Spring washer 12Big plain washer 12

Insulating plate

Insulating plate

48



Step 2: Install support and guide rail

1

6

32

45

6 Leveling pad5 Bolt M12 204 Spring washer 12

3 Plain washer 122 Square nut1 Guide rail


49



Step 3: Install support and guide rail

(3) Bolt M16 35(2) Rack(1) Foot


Foot

Rack

Bolt M16 35Spring washer

Plain washer

50



Step 4: Install floor holder

12

12345

6

8

109

7

11

12 Guide rail11 Insulation plate10 Plain washer 8

9 Bolt M12 308 Spring washer 87 Insulation covering

6 Movable angle plate5 Bolt M12 204 Spring washer 12

3 Plain washer 122 Fixed angle plate1 Square nut


51


34

2

2

1

1


Step 5: Install cabinet

4 Plain washer 123 Spring washer 122 Bolt M12 201 Square nut


52



Step 6: Level the cabinet


1

Washer

BoltM12 20

2

53


--Install P800 supportSupport InstallationSupport Installation


54



1

2

34

5

710

710

138

Customized according to floor height (minimum height is 100 mm)IV

296-455III

216-295II

175-215I

Applicable height of antistatic floor (mm)Support

Heights applicable to P800 serial supports

Introduction to P800 support

6 Height-locking bolt 5 Support height marker4 Hole for connecting guide rail

3 Upper bracket2 Lower bracket1 Hole for connecting floor


55



1

4

7

5

6

23

11

9

8

10

Step 1: Fix the P800 support


56



1

6

32

452

1

3

Step 2: Fix guide rail to P800 support

6 Leveling pad5 Bolt M12 204 Spring washer 12

3 Plain washer122 Square nut1 Guide rail


57


--Install P800 supportStep 3: Install cabinet

34

2

2

1

1

4 Plain washer 123 Spring washer 122 Bolt M12 201 Square nut


58


Step 4: Level the cabinet--Install P800 supportSupport InstallationSupport Installation

BoltM12 20

Washer

59



Effect drawing of installation


60



Step 5: Install floor holder

7

1

2

3

4

5

6

7 Guide rail6 Movable angle plate5 Bolt M12 20

4 Spring washer 123 Plain washer 122 Fixed angle plate1 Square nut


61



Composition of floor holder1 2

3

4

5

67

7 Insulation covering6 Big plain washer 85 Bolt M8 30

4 Spring washer 83 Movable angle plate2 Insulation plate1 Fixed angle plate


62


--Install N300 supportSupport InstallationSupport Installation


63


--Install N300 support

8 Connecting hole on side holder7 Connecting hole on front holder6 Height-locking bolt 5 Height marker of antistatic floor

4 Hole for installation to floor3Hole for connecting cabinet2 Lower bracket1 Upper bracket

Customized according to floor height

(minimum height is 100 mm)

IV

356-595III

236-355II

175-235I


Heights applicable to N300 serial supports

Introduction to N300 support


64



Step 1: Fix N300 support to cement floor

6 Expansion nut5 Expansion tube4 Big plain washer

3 Spring washer 122 Bolt M12 601 Support


65



8 Leveling pad7 Insulating plate

6 Insulation washer5 Big plain washer

4 Spring washer 123 Bolt M12 35

2 Support1 Cabinet

Step 2: Fix cabinet to the support


66


7 Plain washer12

6 Spring washer 125 Bolt M12 304 Side holder

3 Front holder2 Support1 Cabinet

Step 3: Fix the support with floor holder


67




68


5 Hole for installation to floor4 Hole for connecting guide rail3 Lower bracket2 Height marker of antistatic floor1 Upper bracket

Schematic diagram of N800 support

Customized according to floor height (minimum height is 100 mm)IV

346-525III

256-345II

210-255I



69


3

4

5

2

1

A

B

5 Plain washer4 Spring washer 3 Bolt M12 302 Guide rail1 Support


Step 1: Connect N800 to guide rail


70


4

5

1

2

36

6 Plain washer5 Spring washer 4 Bolt M12 30

3 Holder-fixing piece2 Guide rail1 Support


Step 2: Install holder-fixing pieces


71


1

2

3

5

4

6

7

89

9 Nut

8 Plain washer7 Leveling pad6 Insulation plate5 Spring washer

4 Bolt 3 Support2 Guide rail1 Rack


Step 3: Install cabinet


72


1

23

456

7

8

9

456

9 Side holder8 Holder-fixing piece7 Front holder

6 Plain washer125 Spring washer 124 M12 30 bolt

3 Support2 Guide rail1 Cabinet


Step 4: Install floor holders


73


--Install N800 supportEffect drawing of cabinet installed on antistatic floor


74


--Install S300A supportSupport InstallationSupport Installation


75


--Install S300A support

1

2

33. Hole for installation to

floor2. Height marker of antistatic floor1. Hole for connecting

cabinet

Customized according to floor height (minimum

height is 100 mm)IV

356-595III

236-355II

175-235I

Applicable floor height (mm)Specification

Support specifications and heights

Introduction to the support


76



1

4

56

7

8

2

3

Step 1: Draw lines and make holes. Then, fix the support

8. Expansion nut7. Expansion tube

6. Big plain washer 125. Spring washer 124. Bolt M12×60

3. Height-locking bolt (both sides)2. Height-locking bolt (middle)1. Height marker of antistatic floor


77



12345

6

7

89

9. Leveling pad8. Support7. Cabinet-fixing hole6. Insulating pad5. Lower enclosure frame of cabinet4. Insulation covering3. Big plain washer122. Spring washer 121. Bolt M12×40

Step 2: Fix cabinet to support


78



1

45

3

267

7. Plain washer 126. Spring washer 125. Bolt M12 30

4. Horizontal holder3. Support2. Side holder1. Cabinet



79


--Install S600A supportSupport InstallationSupport Installation


80



Introduction to the support

Support specifications and heights

15

4

2

3

(5) Hole for connecting guide rail(4) Hole for installation to floor

(3) Lower bracket(2) Height marker of antistatic floor(1) Upper bracket


Customized according to floor height (minimum height

is 100 mm)IV

346-525III

256-345II

210-255I

Applicable floor height (mm)Specification

81



Step 1: Install guide rail to support2

A

B

1

5

4

3

5 Plain washer4 Spring washer

3 Bolt M12 302 Guide rail1 Support


82



Step 2: Fix support to cement floor1

2

4

5

6

7

8

9

3

9 Leveling pad8 Expansion nut7 Expansion tube

6 Big plain washer5 Spring washer 124 Bolt M12 60

3 Horizontal ruler2 Guide rail1 Support


83


--Install S600A supportStep 3: Install holder-fixing pieces

2

1

6

6

3

5 4

5

4

7

7 Fixing piece for front holder6 Bolt M12 305 Spring washer 12

4 Plain washer123 Fixing piece for side holder2 Support1 Guide rail


84



Effect drawing of support assembly


Fixing piece for side holder

Fixing piece for horizontal holder

Guide rail

Support

85



Step 4: Fix the cabinet

1

2

3

4

5

6

7

89

9 Nut M12

8 Plain washer 127 Guide rail

6 Leveling pad5 Insulation plate

4 Insulation covering3 Plain washer

2 Spring washer 121 Bolt M12 35


86




1

3

4

2

5

6

7

89

4

4

5

6

9 Side holder

8 Fixing piece for side holder

7 Nut M12

6 M12 30Bolt 5 Spring washer 12

4 Plain washer123 Fixing piece for front holder

2 Support1 Guide rail


87



Effect drawing of S600A support installation

1

2

2 Antistatic floor1 Cabinet


88


Installation of outdoor cabinet on base:Install outdoor BTS3812A cabinet, for example, on base

Installation on BaseInstallation on Base --Install BTS3812A cabinet

89


Step 1: Install mounting set--Install BTS3812A cabinet

(1) Cement foundation (2) Mounting set (3) Cabinet (4) Leveling pad

(5) Plain washer 12 (6) Spring washer 12 (7) Bolt M12 35

Installation on Mounting SetInstallation on Mounting Set

90


Step 2: Fix cabinet on the mounting set

--Install BTS3812A cabinetInstallation on Mounting SetInstallation on Mounting Set

(1) Cement foundation (2) Mounting set (3) Cabinet (4) Leveling pad

(5) Plain washer 12 (6) Spring washer 12 (7) Bolt M12 35

(1) Cabinet (2) Mounting set (3) Cement foundation

(5) Plain washer 12(6) Spring washer 12 (4) Bolt M12 35

91


Effect drawing of installation

--Install BTS3812A cabinetInstallation on Mounting SetInstallation on Mounting Set

92


Three installation forms of microcell:Take RRU3801C for example to introduce how to install microcell to pole, wall and stand.

93


(1) (2)

(3) (4) (5)

(1)

(2)(3)

(4)

--Install RRU3801C on pole

(5) M10 45Bolt (4) Spring washer 10

(3) Plain washer10(2) Backplane(1) Fastener

(4) M10 bolt

(3) Spring washer 10(2) Plain washer10(1) Fastener

Fix a pair of fasteners to backplane Connect two pairs of fasteners to fix the pole

Installation on PoleInstallation on Pole

94


(1)

(3)

(2)


(4) RRU3801C module(3) Hooker

(2) M6 12 bolt(1) Hanging plate

(3) Installation slot on backplane

(2) RRU3801C module(1) Hooker on hanging plate

(1)

(2)

(4)

(3)

Fix the hanging plate with RRU3801C Install RRU3801C to backplane


95


(1)

(1)

(2)

(3)


(1) M6X12 bolt (3) Hole of hanging plate(2) Shell of a single RRU(1) Hooker of shell

Fix RRU3801C on backplane Install RRU3801C shell


96


(1)


(1) M6 12 bolt

Fix the plastic shell of RRU3801C Repeat the steps above to install another RRU


97


WallWall--mountingmounting

(1)

(5) (4)(3)

(2)

(1)

(3)

(2)

--Mount RRU3801C to wall

(5) M8 plain washer(4) M8 spring washer

(3) M8 nut(2) Backplane(1) Expansion bolt

(3) Installation slot on backplane

(2) RRU3801C module(1) Hooker on hanging plate

Fix backplane to wall with expansion bolts Install RRU3801C to the backplane, as is done in installation on pole

98


Installation on StandInstallation on Stand

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(7) Expansion nut(6) Expansion tube(5) Insulation pad(4) Spring washer 12(3) Plain washer12(2) M12Bolt (1) Stand

(1)

(2) (3)

(4)

--Install RRU3801C on stand

(4) M10 45 bolt (3) Spring washer 10

(2) Plain washer10(1) Backplane for installing RRU3801C

Fix stand on cement floor Install the backplane on stand

99


(2)

(1)

(3)

--Install RRU3801C on stand

(3) Slot on backplane(2) RRU3801C module(1) Hooker

Install RRU3801C on the backplane

Installation on StandInstallation on Stand

100


(1)

(2)

(3)

--Install RRU3801C on standInstallation on StandInstallation on Stand

(3) Square hole on hanging plate(2) Shell of a single RRU3801C(1) Hooker

Install the plastic shell and install RRU3801C on vertical frame

101


--Install fixation brackets on cabinetInstallation of AccessoriesInstallation of Accessories

Cabinet

Upper bracket

Plane washer

Spring washer

Bolt

102


--Install shockproof piece to cabinet

(4) Channel-section steel(3) Cabinet(2) Shockproof bracket(1) Angle connecting piece

Install shockproof piece to B68-21 cabinet

Installation of AccessoriesInstallation of Accessories

103


Cabling ladder Grooved connecting piece

Right angle connecting piece Cable-through rack

--Install cabling ladder1. Introduction to cabling ladder


104


Triangular bracket Grooved connecting clip

Grooved fixation clip Cable trough

--Install cabling ladderInstallation of AccessoriesInstallation of Accessories

105


Movable bushing End cover

Rectangular frame Channel steel


106


2. Connection form of cabling ladder

Interconnection of cabling troughs


Nut M8

Serrated gasket

Grounding cableBolt M8 20

107


Isoplanar transfer of cabling ladders


Nut M8

Bolt M8 20 Bolt M6 20

Nut M6

108


Non-isoplanar transfer of cabling ladders

Installation of AccessoriesInstallation of Accessories--Install cabling ladder

Nut M8

Bolt M8 20

Bolt M6 20

Nut M6

109


Connect cabling ladder to wall


Nut M6

Bolt M6 20Nut M8 Spring

washer 8Big plain washer 8

Insulation pad

Insulating plate

Expansion bolt M8 80

110


Lap joint on front of climbing ladder


Bolt M8 20

Nut M8

Nut M6

Nut M6 20

111


Lap joint on side of climbing ladder


Bolt M6 20

Nut M6

Bolt M6 20

Nut M6

112


Oblique lap joint of cabling ladders


Nut M8

Bolt M8 20

Nut M8

Bolt M8 20

113


3. Installation forms of cabling ladder

Install the support of upper bracket


Nut M6

Bolt M6 20

114


Suspension of cabling ladder


Expansion bolt M8 80

Insulating plateInsulation padBig plain washer 8Spring washer 8

Nut M8

Bolt M6 20

Nut M6

Nut M8 Bolt M8 20

115


Install triangular support of cabling ladder


Nut M6

Bolt M6 20

116


Connect cabling ladder to cabling trough

4. Install cabling ladder and cabling trough--Install cabling trough


Clip for fixing cabling trough

Nut M8Bolt M8 20

117


Parallel connection of cabling troughs

Installation of AccessoriesInstallation of Accessories--Install cabling trough

Clip for connecting cabling trough

Clip for fixing cabling trough

118


Effect drawing of installation in equipment room

119


Thank you!

cabinet types and their installation

Documents