ca l1-l44.qxd:layout 1 2/10/11 9:01 am page 1...dp bp c d ac af 05-2330 w sealing gland † the cpt...

L

ca_L1-L44.qxd:Layout 1 2/10/11 9:01 AM

L-30

www.ittcannon.com

Dimensions shown in mm (inch)Specifications and dimensions subject to change

L

VEA

M P

T

PT55/PTG55

PT55A/PTG55A PT55SE/PTG55SE

PT55/PTG55

PT55/PTSE/PTG55/PTSE

PT55/PTG55

LA V THD

DA

05-0532adaptor

Type A

.395(10.03)

Min.

LBF

GBF HBF

05-1778 strain relief clamp05-0120 SR and grommet

05-0186 SR Clamp

LBF

GBF HBF

BE

LE

05-0114 external grommetclamp nut

05-2042 potting boot

LP

DP BP

C DAC AF

05-2330 W sealing gland

• The CPT range is a proprietary design and is a commercial version of the PTSE crimp contact connectors, available in shell sizes 8 to 18.

• They are intermateable and interchangeable with PT and PTSEranges and offer similar mechanical and electrical performance.

• CPT77A jam nut receptacle with external rear accessory thread (crimp contacts)• CPT07E jam nut receptacle with internal rear accessory thread (crimp contacts)• CPT02 mount receptacle with without rear accessory thread (crimp contacts)• CPT33A wall mount receptacle with external rear accessory thread (crimp contacts)• CPT44A line connecting receptacle (no fixing holes) with rear accessory thread (crimp contacts)• CPT55A straight plug with standard coupling nut (crimp contacts)• CPT55AT01 straight plug with ribbed coupling nut (crimp contacts)• CPTG55A straight plug with standard coupling nut/grounding spring (crimp contacts)• CPTG55AT01 straight plug with ribbed coupling nut/grounding spring (crimp contacts)

• Since they use standard PT hardware they are dimensionally similar to that range, and all relevant dimensions can be obtained from that section of this catalog.

• CPT connectors can be supplied with or without contacts. Details of CPT contacts can be found in the “contacts” section of this catalog.

For dimensional data see accessories section on page’s 33 to 39.

Strain relief clamps are not supplied with cable clamp grommet.

For connector supplied complete with relevant accessory pleaseuse cross reference chart on page 43 or consult factory.

Protective caps are located on page 33.

VEAM PT Connectors

PT Plug Accessories

CPT Connectors

Available CPT variants in shell sizes 8 thru 18

ca_L1-L44.qxd:Layout 1 2/10/11 9:01 AM Page 30

L-31

www.ittcannon.com


L

VEA

M PT

InsertionRemove the connector rear accessories that may be fitted and thread them on to the cables. Locatewire and crimped contact in the tool, insert the contact in to the relevant contact cavity from therear. Maintain alignment with the axis of the connector until the contact is located in the correctposition. With PTSE connectors a slight click may be heard as the positive stop is felt. All contactsmust be fitted and sealing plugs used behind any contacts that are not wired.

RemovalRemove the connector back fittings. Align the tool over the front of the contact and maintain gen-tle pressure on the tool while pushing forward to eject the contact. With PTSE range the tip of thetool must locate in the contact retention device. Do not attempt to tilt or rotate the tool within theconnector.

Contacts Insertion Extraction Tool Crimp Tool Locator

20 PTSE 05-2231-20 05-2230-20 M22520/1-01 M22520/1-02

20 PTSE 05-0407-20 05-2230-20 M22520/1-01 M22520/1-02

16 PTSE 05-2231-20 05-2230-16 M22520/1-01 M22520/1-02

16 PTSE 05-2231-20 05-2230-20 M22520/1-01 M22520/1-02

20&20/22CPT 05-0484-20 05-0485-20 M22520/1-01 TH254

16CPT 05-2231-16 05-2230-16 M22520/1-01 TH254

Insertion Tools

A43240Removal Kit

VEAM PT Connectors

Crimp Contacts Insertion & Removal

ca_L1-L44.qxd:Layout 1 2/10/11 9:01 AM 1

L-32

www.ittcannon.com


L

VEA

M P

T

size Part Number Part Number Color Wires Aw

20 Pin 05-1124 Socket 05-2376 05-2661-A20 red 24, 22 & 20

20 Pin 05-1127 Socket 05-1128 05-2661-A20 red 24, 22 & 20

16 Pin 05-1130 Socket 05-1131 05-2661-16 blue 18 & 16

12 Pin 05-1133 Socket 05-1134 05-2661-12 yellow 14 & 12

size Part Number Shell Size Part Number Color Wires Awg

20 Pin 05-1136 Socket 05-1138 8-18 05-2661-A20 red 24, 22 & 20

20/22 Pin 05-1171 Socket 05-1173 8-18 05-2661-A20 red 24, 22 & ??

16 Pin 05-1142 Socket 05-1144 8-18 05-2661-16 blue 18 & 16

CPT CONTACTS SEALING PLUGS

PTSE CONTACTS SEALING PLUGS

CPT contacts are available for Shellsizes 8 thru 18 only.

Size 20 solder contact

Nominal rating: 5 ampsStripping length: 1/8”

Size 16 solder contactNominal rating: 15 amps

Stripping length: 3/16”

Size 12 solder contactNominal rating: 24 amps

Stripping length: 3/16”

Size 20 contacts S.E. range

Nominal rating: 15 ampsStripping length: _”

Size 16 contact S.E. range

Nominal rating: 15 ampsStripping length: 1/4”

Co axial contacts S.E. rangefor RG. 180/U RG. 195/U

cables or equivalents

3

Size 12 contacts S.E. rangeNominal rating: 24 ampsStripping length: 1/4”

VEAM PT Connectors

Contacts, Tools & Assembly (PTSE, CPT)


L-33

www.ittcannon.com


L

VEA

M PT

VEAM PT Connectors

Patt 105/603 Metal Dustcap for PT & PTSE connectors (& 26482 ser 1 &2)

Metal dust caps for PT and PTSEconnectors. The PTA artic cap optionhas been designed to ease handtightening. A silicone gasket isincluded with the cap.

Plug

Receptacle

PT KNURLED CAP.75 +/- .02 (19.0 +/- 0.5)GASKET

OA OBAR

O

KNURLEDGRIP

CRIMP FERRULE OPTION(SUPPLIED LOOSE)

EYELET OPTIONOF

O DPTA ARTIC CAP

GASKET

PTA ARTIC CAPPT KNURLED CAP

KNURLEDGRIP

RING OPTION(FITS OVER JAM NUT THREAD)

EYELET OPTION

CRIMP FERRULE OPTION(SUPPLIED LOOSE)

OF

O E

AR

O OC

.73 +/- .02 (18.5 +/- 0.5)

PT knurled capPTA artic cap

dust capPD - plug dust capDR - dust cap receptacle

shell size

material1 = aluminium

platingEN = elecroless nickelODC = olive drab cadmiumZNB = black zinc nickelZCO = olive drab zinc cobaltZCB = black zinc cobalt

Lanyard typeNL - Not fittedNR - nylon covered wire ropeTR - teflon covered wire ropeLC - stainless steel link chainPC - olive drab polyester cord

Lanyard length (inches)

Attachment type00 - not fitted01 - eyelet intl dia (F) 3.2 mm02 - eyelet intl dia (F) 3.7 mm03 - eyelet intl dia (F) 4.3 mm04 - eyelet intl dia (F) 5.3 mm05 - eyelet intl dia (F) 6.4 mmRG - ring to fit over connector thread

PTA - PD- 8-1-EN - TR 5-03SHELL SIZE A MAX AR MAX B MAX C MAX D MAX E MAX

8 .709 (18.0) .787 (20.0) .472 (12.0) .681 (17.3) .594 (15.1) .594 (15.1)

10 .827 (21.0) .906 (23.0) .591 (15.0) .799 (20.3) .634 (16.1) .709 (18.0)

12 .984 (25.0) 1.063 (27.0) .752 (19.1) .957 (24.3) .764 (19.4) .890 (22.6)

14 1.102 (28.0) 1.181 (30.0) .874 (22.2) 1.075 (27.3) .890 (22.6) 1.016 (25.8)

16 1.220 (31.0) 1.339 (34.0) 1.000 (25.4) 1.232 (31.3) 1.016 (25.8) 1.134 (28.8)

18 1.339 (34.0) 1.496 (38.0) 1.126 (28.6) 1.390 (35.3) 1.094 (27.8) 1.260 (32.0)

20 1.457 (37.0) 1.575 (40.0) 1.252 (31.8) 1.469 (37.3) 1.205 (30.6) 1.378 (35.0)

22 1.575 (40.0) 1.732 (44.0) 1.374 (34.9) 1.606 (40.8) 1.343 (34.1) 1.508 (38.3)

24 1.713 (43.5) 1.811 (46.0) 1.500 (38.1) 1.724 (43.8) 1.453 (36.9) 1.642 (41.7)


L-34

www.ittcannon.com


L

VEA

M P

T

Size Front Thread F Cable Diameter C Length A Diameter D8 7/16 x 28UNEF 0.600 0.650 0.190

10 9/16 x 24UNEF 0.730 0.650 0.190

12 11/16 x 24UNEF 0.860 0.650 0.190

14 13/16 x 20UNEF 0.990 0.650 0.190

16 15/16 x 20UNEF 1.110 0.650 0.190

18 1 1/16 x 18UNEF 1.240 0.650 0.190

20 1 3/16 x 18UNEF 1.360 0.680 0.190

22 1 5/16 x 18UNEF 1.480 0.680 0.190

24 1 7/16 x 18unef 1.510 0.680 0.190

Size Front Thread F Rear Thread D Length A Diameter B8 7/16 x 28UNEF 1/2 x 28UNEF 0.935 0.590

10 9/16 x 24UNEF 5/8 x 24UNEF 0.935 0.720

12 11/16 x 24UNEF 3/4 x 20UNEF 0.935 0.850

14 13/16 x 20UNEF 7/8 x 20UNEF 0.935 0.980

16 15/16 x 20UNEF 1 x 20UNEF 0.935 1.096

18 1 1/16 x 18UNEF 1 3/16 x 18UNEF 0.935 1.210

20 1 3/16 x 18UNEF 1 3/16 x 18UNEF 0.935 1.350

22 1 5/16 x 18UNEF 1 7/16 x 18UNEF 0.935 1.480

24 1 7/16 x 18unef 1 7/16 x 18UNEF 0.935 1.600

A max.

øC m

ax.

øD T

HD

øF

øB M

ax.

UN

EF

- 2B

F TH

RE

AD

A

0a

To correctly specify accessory part number replace XX with shell size required and plating needed which can be found inHow to order section of each connector type. ie 05 0532 8 T69

To correctly specify accessory part number replace XX with insert arrangement required and plating needed which canbe found in How to order section of each connector type. ie 05 0114 8 98 T69

VEAM PT Connectors

A Threaded Type Adapter 05-0532-xx

E Type Grommet Clamp Nut 05 0114 XX XX


L-35

www.ittcannon.com


L

VEA

M PT

Size Front Thread F Cable Diameter C Length A Diameter D8 7/16 x 28UNEF 0.230 1.055 0.560

10 9/16 x 24UNEF 0.312 1.055 0.684

12 11/16 x 24UNEF 0.442 1.155 0.810

14 13/16 x 20UNEF 0.539 1.300 0.935

16 15/16 x 20UNEF 0.614 1.524 1.060

18 1 1/16 x 18UNEF 0.672 1.724 1.185

20 1 3/16 x 18UNEF 0.744 1.925 1.310

22 1 5/16 x 18UNEF 0.844 2.135 1.435

24 1 7/16 x 18unef 0.890 2.175 1.560

Size Front Thread Diameter N Max Clamp Width H Cable Size G Length L Grommet P/N8 7/16 x 28UNEF 0.550 0.812 0.125 1.761 10-36565-101

10 9/16 x 24UNEF 0.675 0.875 0.188 1.761 10-36565-122

12 11/16 x 24UNEF 0.803 1.000 0.312 1.761 10-36565-143

14 13/16 x 20UNEF 0.920 1.125 0.375 1.761 10-36565-163

16 15/16 x 20UNEF 0.047 1.188 0.500 1.893 10-36565-183

18 1 1/16 x 18UNEF 1.165 1.438 0.625 1.893 10-36565-203

20 1 3/16 x 18UNEF 1.290 1.438 0.625 2.081 10-36565-203

22 1 5/16 x 18UNEF 1.418 1.719 0.750 2.081 10-36565-244

24 1 7/16 x 18unef 1.543 1.750 0.800 2.143 10-36565-232

05-1778-XXBasic SR clamp

05-0120-XX-XXwith Grommet

05-1886-XXfor SE connector

NSR

LSR

GSR

DSR

HSR

C

A

øF

øC

MA

X.

øD

MA

X.

UN

EF

- 2

B


To correctly specify accessory part number replace XX with shell size/insert layout required and plating needed which can be found in How to order section of each connector type. Cable clamp grommet sold separately. See page 33.

VEAM PT Connectors

Strain Relief Clamps

W Type Sealing Gland 05 2330 XX


L-36

www.ittcannon.com


L

VEA

M P

T Size Front Thread F Diameter T Length N Max Cable Size8 7/16 x 28UNEF 0.690 2.020 0.283

10 9/16 x 24UNEF 0.760 2.020 0.343

12 11/16 x 24UNEF 0.856 2.492 0.465

14 13/16 x 20UNEF 1.044 2.516 0.492

16 15/16 x 20UNEF 1.174 2.640 0.575

18 Consult Factory

20 1 3/16 x 18UNEF 1.404 2.640 0.657

22 Consult Factory

24 1 7/16 x 18UNEF 1.654 3.015 0.800

Size Front Thread F Diameter B Length L Outlet Size D8 7/16 x 28UNEF 0.608 1.526 0.317

10 9/16 x 24UNEF 0.734 1.526 0.434

12 11/16 x 24UNEF 0.858 1.526 0.548

14 13/16 x 20UNEF 0.984 1.526 0.673

16 15/16 x 20UNEF 1.110 1.526 0.798

18 1 1/16 x 18UNEF 1.234 1.526 0.899

20 1 3/16 x 18UNEF 1.360 1.646 1.024

22 1 5/16 x 18UNEF 1.484 1.646 1.149

24 1 7/16 x 18unef 1.610 1.646 1.274

LP

DPBP

X A

/F

ØS

max. c

able

UN

EF

-2B

ØF

ØT

max.

N



VEAM PT Connectors

P Type Potting Boot 05 2042 XX

Straight Outlet for Def Stan Cable 05 2058 XX


L-37

www.ittcannon.com


L

VEA

M PT

VEAM PT Connectors

Patt 105/603 Metal Backshell for PT & PTSE Connectors

A machined metal backshell offeringa 360 degree shield by fixing thecable braid with a self-tensioned,metal spring. The spring can beopened and re-used without the needfor any special tooling. (Band-it strapsmay also be used - see ordering info.)

ANGLE 1

ØT

34,00 ± 0,25

ØG

ØH

AT

HR

EA

D

ØB

I

ANGLE 2

C

D

I

SILICONE O RING

CIRCLIP

ANGLE 3

K

E

F

SHELL SIZE A THREAD B MAX T MIN C +/-.02 (0.5) D +/-.02 (0.5) E MAX F MAX K +/-.02 (0.5)

8 7/16-28 UNEF .681 (17.3) .276 (7.0) .555 (14.1) .972 (24.7) .992 (25.2) 1.197 (30.4) .689 (17.5)

10 9/16-24 UNEF .799 (20.3) .378 (9.6) .587 (14.9) 1.020 (25.9) 1.110 (28.2) 1.268 (32.2) .732 (18.6)

12 11/16-24 UNEF .937 (23.8) .524 (13.3) .602 (15.3) 1.035 (26.3) 1.248 (31.7) 1.327 (33.7) .807 (20.5)

14 13/16-20 UNEF 1.055 (26.8) .618 (15.7) .638 (16.2) 1.071 (27.2) 1.386 (35.2) 1.386 (35.2) .886 (22.5)

16 15/16-20 UNEF 1.173 (29.8) .740 (18.8) .650 (16.5) 1.102 (28.0) 1.504 (38.2) 1.453 (36.9) .945 (24.0)

18 1 1/16-18 UNEF 1.311 (33.3) .835 (21.2) .681 (17.3) 1.114 (28.3) 1.642 (41.7) 1.516 (38.5) 1.024 (26.0)

20 1 3/16-18 UNEF 1.429 (36.3) .961 (24.4) .717 (18.2) 1.146 (29.1) 1.780 (45.2) 1.618 (41.1) 1.102 (28.0)

22 1 5/16-18 UNEF 1.567 (39.8) 1.087 (27.6) .728 (18.5) 1.161 (29.5) 1.898 (48.2) 1.638 (41.6) 1.161 (29.5)

24 1 7/16-18 UNEF 1.685 (42.8) 1.213 (30.8) .764 (19.4) 1.197 (30.4) 2.016 (51.2) 1.697 (43.1) 1.220 (31.0)

CABLE ENTRY G MIN H MAX03 .185 (4.7) .547 (13.9)04 .248 (6.3) .547 (13.9)05 .311 (7.9) .610 (15.5)06 .374 (9.5) .677 (17.2)07 .437 (11.1) .736 (18.7)08 .500 (12.7) .799 (20.3)09 .559 (14.2) .862 (21.9)10 .622 (15.8) .925 (23.5)11 .685 (17.4) .988 (25.1)12 .748 (19.0) 1.051 (26.7)13 .811 (20.6) 1.114 (28.3)14 .874 (22.2) 1.177 (29.9)15 .937 (23.8) 1.240 (31.5)16 1.000 (25.4) 1.303 (33.1)17 1.063 (27.0) 1.366 (34.7)18 1.126 (28.6) 1.429 (36.3)19 1.189 (30.2) 1.492 (37.9)20 1.252 (31.8) 1.555 (39.5)21 1.311 (33.3) 1.618 (41.1)22 1.378 (35.0) 1.681 (42.7)23 1.437 (36.5) 1.744 (44.3)24 1.500 (38.1) 1.807 (45.9)

PT - patt 105also fits PTSE patt 603screened spring adaptor

cable entry angle1 = straight2 = 45 deg3 = 90 deg

shell size

cable entry size



Braid fixingLeave blank if none requiredS - self tensioning springB - band-it tie wrap

PT-SSA- 1-10-04- 1-EN-S


L-38

www.ittcannon.com


L

VEA

M P

TVEAM PT Connectors

Patt 105/603 Metal Backshell for PT & PTSE Connectors

A machined metal backshell that trapsthe cable braid with either a plain nutor cable clamp to give a 360°screened termination.

ANGLE 1

39,00 ± 0,25 J

ØG WØT

AT

HR

EA

D

ØB

I

I

ANGLE 2

C

D

JI

SILICONE O RING

34,00 ± 0,25

ØH

PLAIN NUT OPTION

ANGLE 3

K

E

FJ

PT - patt 105also fits PTSE patt 603braid trap adaptor

cable entry angle1 = straight2 = 45 deg3 = 90 deg

shell size

cable entry size



Cable fixingBlank - plain nutCC - cable clamp

PT- BTA- 1-10-04- 1-EN-CC

CLAMP NUT CLAMP NUT

SHELL SIZE A THREAD B MAX T MIN C MAX D MAX D MAX E MAX F MAX F MAX K +/-.02 (+/-0.5)

8 7/16-28 UNEF .681 (17.3) .276 (7.0) .555 (14.1) .941 (23.9) .783 (19.9) .992 (25.2) 1.201 (30.5) 1.043 (26.5) .689 (17.5)

10 9/16-24 UNEF .799 (20.3) .378 (9.6) .587 (14.9) .969 (24.6) .811 (20.6) 1.110 (28.2) 1.268 (32.2) 1.110 (28.2) .732 (18.6)

12 11/16-24 UNEF .937 (23.8) .524 (13.3) .602 (15.3) .984 (25.0) .827 (21.0) 1.248 (31.7) 1.327 (33.7) 1.287 (32.7) .807 (20.5)

14 13/16-20 UNEF 1.055 (26.8) .618 (15.7) .638 (16.2) 1.020 (25.9) .862 (21.9) 1.386 (35.2) 1.386 (35.2) 1.228 (31.2) .886 (22.5)

16 15/16-20 UNEF 1.173 (29.8) .740 (18.8) .650 (16.5) 1.051 (26.7) .894 (22.7) 1.504 (38.2) 1.453 (36.9) 1.295 (32.9) .945 (24.0)

18 1 1/16-18 UNEF 1.311 (33.3) .835 (21.2) .681 (17.3) 1.063 (27.0) .906 (23.0) 1.642 (41.7) 1.516 (38.5) 1.362 (34.6) 1.024 (26.0)

20 1 3/16-18 UNEF 1.429 (36.3) .961 (24.4) .717 (18.2) 1.098 (27.9) .941 (23.9) 1.780 (45.2) 1.579 (40.1) 1.425 (36.2) 1.102 (28.0)

22 1 5/16-18 UNEF 1.567 (39.8) 1.087 (27.6) .728 (18.5) 1.114 (28.3) .957 (24.3) 1.898 (48.2) 1.638 (41.6) 1.480 (37.6) 1.161 (29.5)

24 1 7/16-18 UNEF 1.685 (42.8) 1.213 (30.8) .764 (19.4) 1.146 (29.1) .988 (25.1) 2.016 (51.2) 1.697 (43.1) 1.539 (39.1) 1.220 (31.0)

NUT CLAMP CLAMPCABLE ENTRY G MIN H MAX W MAX J MAX

03 .185 (4.7) .598 (15.2) .681 (17.3) .500 (12.7)04 .248 (6.3) .598 (15.2) .744 (18.9) .500 (12.7)05 .311 (7.9) .661 (16.8) .807 (20.5) .500 (12.7)06 .374 (9.5) .724 (18.4) .870 (22.1) .500 (12.7)07 .437 (11.1) .787 (20.0) .929 (23.6) .500 (12.7)08 .500 (12.7) .850 (21.6) .988 (25.1) .618 (15.7)09 .559 (14.2) .913 (23.2) 1.055 (26.8) .618 (15.7)10 .622 (15.8) .976 (24.8) 1.118 (28.4) .618 (15.7)11 .685 (17.4) 1.039 (26.4) 1.185 (30.1) .736 (18.7)12 .748 (19.0) 1.098 (27.9) 1.244 (31.6) .736 (18.7)13 .811 (20.6) 1.161 (29.5) 1.303 (33.1) .736 (18.7)14 .874 (22.2) 1.224 (31.1) 1.370 (34.8) .854 (21.7)15 .937 (23.8) 1.287 (32.7) 1.437 (36.5) .854 (21.7)16 1.000 (25.4) 1.350 (34.3) 1.492 (37.9) .854 (21.7)17 1.063 (27.0) 1.413 (35.9) 1.555 (39.5) .854 (21.7)18 1.126 (28.6) 1.476 (37.5) 1.618 (41.1) .854 (21.7)19 1.189 (30.2) 1.547 (39.3) 1.681 (42.7) .913 (23.2)20 1.252 (31.8) 1.598 (40.6) 1.744 (44.3) .913 (23.2)21 1.311 (33.3) 1.661 (42.2) 1.803 (45.8) .913 (23.2)22 1.378 (35.0) 1.724 (43.8) N/A N/A23 1.437 (36.5) 1.787 (45.4) 1.866 (47.4) .913 (23.2)24 1.500 (38.1) 1.850 (47.0) 2.004 (50.9) .913 (23.2)


L-39

www.ittcannon.com


L

VEA

M PT

(Contact factory for further examples)

• 05-3226 screw-on direct harness Adapter

• 05-3228 long screw-on cable support

• 05-0364 short screw-on cable support

• 05-3229 long screw-on Adapter with screentrap

L

D

D

L

F B

F B

D

L

F B

F BD

L

VEAM PT Connectors

Special Accessories


L-40

www.ittcannon.com


L

VEA

M P

TVEAM PT Connectors

B D L FPART SHELL SIZE DIAMETER THREAD LENGTH CABLE DIAMETER

05-0364-81 8 0.593 .5000 x 28unef 1.185 0.195

05-0364-82 8 0.593 .5000 x 28unef 1.185 0.250

05-3226-1 8 0.593 .5000 x 28unef 0.997 0.332

05-3228-1 8 0.593 .5000 x 28unef 0.563 0.210

05-3228-11 8 0.593 .5000 x 28unef 2.1320 0.210

05-3228-2 8 0.593 .5000 x 28unef 0.563 0.250

05-3229-1 8 0.593 .5000 x 28unef 1.185 0.195

05-3229-11 8 0.593 .5000 x 28unef 2.760 0.210

05-3229-2 8 0.593 .5000 x 28unef 1.185 0.250

05-0364-101 10 0.719 .6250 x 24unef 1.360 0.195

05-0364-102 10 0.719 .6250 x 24unef 1.360 0.250

05-0364-103 10 0.719 .6250 x 24unef 1.360 0.281

05-3226-2 10 0.719 .6250 x 24unef 1.047 0.419

05-3228-10 10 0.719 .6250 x 24unef 2.088 0.317

05-3228-3 10 0.719 .6250 x 24unef 0.688 0.195

05-3228-4 10 0.719 .6250 x 24unef 0.688 0.250

05-3228-5 10 0.719 .6250 x 24unef 0.688 0.281

05-3228-7 10 0.719 .6250 x 24unef 2.088 0.215

05-3228-8 10 0.719 .6250 x 24unef 2.088 0.255

05-3228-9 10 0.719 .6250 x 24unef 2.088 0.290

05-3229-10 10 0.719 .6250 x 24unef 2.760 0.317

05-3229-3 10 0.719 .6250 x 24unef 1.360 0.195

05-3229-4 10 0.719 .6250 x 24unef 1.360 0.250

05-3229-5 10 0.719 .6250 x 24unef 1.360 0.281

05-3229-7 10 0.719 .6250 x 24unef 2.760 0.215

05-3229-8 10 0.719 .6250 x 24unef 2.760 0.255

05-3229-9 10 0.719 .6250 x 24unef 2.760 0.290

05-0364-123 12 0.843 .7500 x 20unef 1.310 0.385

05-3226-3 12 0.843 .7500 x 20unef 1.042 0.582

05-3228-6 12 0.843 .7500 x 20unef 0.643 0.385

05-3229-3 12 0.843 .7500 x 20unef 1.310 0.195

Special Adapter Dimensions


L-41

www.ittcannon.com


L

VEA

M PT

CONNECTOR STYLE CABLE

8-4

8-33

8-98

10-2

10-6

10-7

10-9

9

12-1

0PART NUMBER &DESCRIPTION

ARRANGEMENTS

05-0596-XXcrimp contacts

Deft STAN 61-12 (pt 7)crimp contacts




SD3/229879RSRE 040/01

SD3/229879RSRE 040/01

SD3/229879RSRE 040/01

SD3/229879RSRE 040/01

SD4/24127BS.6500 table 16

05-2041-XXsolder contacts

05-1311-XXcrimp contacts for lightweight tinsel cable

STRAIGHT PLUGS(bayonet coupling)

STRAIGHT PLUG(bayonet coupling)

STRAIGHT PLUGS(quick release)

STRAIGHT PLUG(quick release)


05-1630-XXcrimp contacts non pre-ferred use 05 1312

05-1312-XX crimp contacts for

light-weight tinsel cable

05-1093-XX crimp contacts for lightweight tinsel cable

05-2467-XXcrimp contacts non pre-ferred use 051093

05-2040-XX

crimp contacts

05-2468-XXcrimp contacts non pre-ferred use 05 2040

• • • • •

• • • • • •

• • • • • • • •

• • •

• • •

• • •

• • •

• • •

• • •

•

To complete Audio connector part numbers replace xx with insert arrangement, contact gender, orientation and plating finish.

Audio Connectors

VEAM PT Connectors


L-42

www.ittcannon.com


L

VEA

M P

TVEAM PT Connectors

CONNECTOR STYLE CABLE

8-4

8-33

8-98

10-2

10-6

10-7

10-9

9

12-1

0PART NUMBER &DESCRIPTION

ARRANGEMENTS

05-0599-XXsolder contacts, ‘O’ ringseal, hexagonal nut only

05-2676-XXsolder contacts, ‘O’ ringseal, hexagonal nut onlynon preferred use 05 0599

05-1626-XXsolder contacts, hexagonal nut only

05-1319-XXsolder contacts, ring nut only

OPEN WIRING

OPEN WIRING

OPEN WIRING

OPEN WIRING

OPEN WIRING

Deft STAN 61-12 (pt 4)7-2-6C

Deft STAN 61-12 (pt 4)7-2-6C

Def STAN 61-12 (pt 4)7-2-6C

SD3/229879RSRE 040/01

SD3/229879RSRE 040/01

SD4/246127BS.6500 table 16

PANEL MOUNTINGRECEPTACLES

(bayonet coupling)

PANEL MOUNTING RECEPTACLES

LINE CONNECTING RECEPTACLES

90 DEGREE PLUG

90 DEGREE PLUGS


05-1320-XXcrimp contacts for light-weight tinsel cable


05-1318-XXsolder contacts, no fittings



05-2339-XXsolder contacts, and screentermination outlet

• • •

• • •

• • • • •

• • • • • •

• • • •

• • •

• • •

• • •

• • • •

• • • •

•

Audio Connectors


L

VEA

M PT

PT55

A

PT55

A(T

01)

CPT

55A

CPT

55A

(T01

)

PTG

55A

PTG

55A

(T01

)

CPT

G55

A

CPT

G55

A(T

01)

PT55

SE

PT55

SE(T

01)

PTG

55SE

PTG

55SE

(T01

)

PT02

PT33

A

CPT

02

CPT

33A

PT02

SE

PT33

SE

PTB

PT44

A

CPT

44A

PT44

SE

PT07

A

PT07

E

PT07

SE

PT77

A

CPT

77A

PT77

SE

PT06

A

PT06

A(T0

1)

CPT

06A

CPT

06A(

T01)

PTG

06A

PTG

06A(

T01)

CPT

G06

A

CPT

G06

A(T0

1)

NA

NA

NA

NA

NA

PT00

A

NA

CPT

00A

NA

NA

NA

PT01

A

CPT

01A

NA

NA

NA

NA

NA

NA

NA

PT06

A(SR

)

PT06

A(T0

1)

CPT

06A(

SR)

CPT

06A(

T01)

PTG

06A(

SR)

PTG

06A(

T02)

CPT

G06

A(SR

)

CPT

G06

A(T0

2)

NA

NA

NA

NA

NA

PT00

A(SR

)

NA

CPT

00A(

SR)

NA

NA

NA

PT01

A(SR

)

CPT

01A(

SR)

NA

NA

NA

NA

NA

NA

NA

PT06

E

PTG

06E(

T01)

CPT

06E

CPT

06E(

T01)

PT06

E

PTG

06E(

T01)

CPT

G06

E

CPT

G06

E(T0

1)

NA

NA

NA

NA

NA

PT00

E

NA

CPT

00E

NA

NA

NA

PT01

E

CPT

01E

NA

NA

NA

NA

PT07

E(T1

1)

CPT

07E(

T11)

NA

NA

NA

NA

NA

NA

NA

NA

NA

PT06

SE

PT06

SE(T

01)

PTG

06SE

PTG

06SE

(T01

)

NA

NA

NA

NA

NA

PT00

SE

NA

NA

NA

PT01

SE

NA

NA

PT07

SE

NA

NA

PT07

SE(T

11)

PT06

E(SR

)

PT06

E(T0

1)

CPT

06E(

SR)

CPT

06E(

T02)

PTG

06E(

SR)

PTG

06E(

T01)

CPT

G06

E(SR

)

CPT

G06

E(T0

2)

NA

NA

NA

NA

NA

PT00

E(SR

)

NA

CPT

00E(

SR)

NA

NA

NA

PT01

E(SR

)

CPT

01E(

SR)

NA

NA

NA

NA

PT07

E(T1

2)

CPT

07E(

T12)

NA

NA

NA

NA

NA

NA

NA

NA

NA

PT06

SE(S

R)

PT06

SE(T

02)

PTG

06SE

(SR

)

PTG

06SE

(T02

)

NA

NA

NA

NA

NA

PT00

SE(S

R)

NA

NA

NA

PT01

SE(S

R)

NA

NA

PT07

SE(S

R)

NA

NA

PT07

SE(T

12)

PT06

P

PT06

P(T0

1)

CPT

06P

CPT

06P(

T01)

PTG

06P

PTG

06P(

T01)

CPT

G06

P

CPT

G06

P(T0

1)

PT06

SP

PT06

SP(T

01)

PTG

06SP

PTG

06SP

(T01

)

NA

PT00

P

NA

CPT

00P

NA

PT00

SP

NA

PT01

P

CPT

01P

PT01

SP

NA

NA

PT07

SP

PT07

P(T1

1)

CPT

07P(

T11)

PT07

SP(T

11)

PT06

PSR

PT06

P(T0

2)

CPT

06P(

SR)

CPT

06P(

T02)

PTG

06P(

SR)

PTG

06P(

T02)

CPT

G06

P(SR

)

CPT

G06

P(T0

2)

NA

NA

NA

NA

NA

PT00

P(SR

)

NA

CPT

00P(

SR)

NA

NA

NA

PT01

P(SR

)

CPT

01P(

SR)

NA

NA

NA

NA

NA

NA

NA

PT06

W

PT06

W(T

01)

CPT

06W

CPT

06W

(T01

)

PTG

06W

PTG

06W

(T01

)

CPT

G06

W

CPT

G06

W(T

01)

NA

NA

NA

NA

NA

PT00

W

NA

CPT

00W

NA

NA

NA

PT01

W

CPT

01W

NA

NA

NA

NA

NA

NA

NA

PT66

PT66

(T01

)

CPT

66

CPT

666(

T01)

PTG

66

PTG

66(T

01)

CPT

G66

CPT

G66

(T01

)

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

PT66

SE

PT66

SE(T

01)

PTG

66SE

PTG

66SE

(T01

)

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

PT88

SE

PT88

SE(T

01)

PTG

88SE

PTG

88SE

(T01

)

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

PT88

PT88

(T01

)

CPT

88

CPT

88(T

01)

PTG

88

PTG

88(T

01)

CPT

G88

CPT

G88

(T01

)

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

PT08

A

PT08

A(T0

1)

CPT

08A

CPT

08A(

T01)

PTG

08A

PTG

08A(

T01)

CPT

G08

A

CPT

G08

A(T0

1)

PT08

SE

PT08

SE(T

01)

PTG

08SE

PTG

08SE

(T01

)

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

PT08

E

PT08

E(T0

1)

CPT

08E

CPT

08E(

T01)

PTG

08E

PTG

08E(

T01)

CPT

G08

E

CPT

G08

E(T0

1)

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

NA

P TYPE SR CLAMP 05-1778-XX

P TYPE POTTING BOOT 05-2042-XX

SE TYPE SR CLAMP 05-0186-XX-XX

E TYPE SR CLAMP 05-0120-XX-XX

SE TYPE CLAMP NUT 05-0184-XX

E TYPE CLAMP NUT 05-0114-XX-XX

A TYPE SR CLAMP 05-1778-XX

A TYPE ADAPTOR 05-0532-X

W TYPE SEALING GLAND 05-2330-XX

SE STRAIGHT OUTLET 05-2309-XX-XX

75 DEGREE OUTLET 05-2060-XX-XX

STRAIGHT OUTLET 05-2058-XX-XX

75 DEGREE OUTLET 05-2311-XX-XX

A TYPE 90 DEGREE ELBOW 05-1774-XX

E TYPE 90 DEGREE ELBOW WITH

GROMMET 05-1774-XX +

Connector Plus Cross Reference

L-43

www.ittcannon.com


VEAM PT Connectors


L-44

www.ittcannon.com


L

VEA

M P

T

THIS NOTE MUST BE READ IN CONJUNC-TION WITH THE PRODUCT DATASHEET/CATALOG. FAILURE TO OBSERVETHE ADVICE IN THIS INFORMATION SHEETAND THE OPERATING CONDITIONS SPECI-FIED IN THE PRODUCT DATA SHEET/ CATA-LOG COULD RESULT IN HAZARDOUS SITU-ATIONS.

1. MATERIAL CONTENT AND PHYSICALFORMElectrical connectors do not usually containhazardous materials. They contain conduct-ing and non-conducting materials and canbe divided into two groups.a) Printed circuit types and low cost audiotypes which employ all plastic insulatorsand casings.b) Rugged, Fire Barrier and High Reliabilitytypes with metal casings and either naturalrubber, synthetic rubber, plastic or glassinsulating materials. Contact materials varywith type of connector and also applicationand are usually manufactured from either:Copper, copper alloys, nickel, alumel,chromel or steel. In special applications,other alloys may be specified.

2. FIRE CHARACTERISTICS AND ELECTRICSHOCK HAZARDThere is no fire hazard when the connec-tor is correctly wired and used within thespecified parameters. Incorrect wiring orassembly of the connector or careless useof metal tools or conductive fluids, ortransit damage to any of the componentparts may cause electric shock or burns.Live circuits must not be broken by sepa-rating mated connectors as this maycause arcing, ionization and burning.Heat dissipation is greater at maximumresistance in a circuit. Hot spots may occurwhen resistance is raised locally by damage,e.g. cracked or deformed contacts, brokenstrands of wire. Local overheating may alsoresult from the use of the incorrect applica-tion tools or from poor quality soldering orslack screw terminals. Overheating mayoccur if the ratings in the product DataSheet/Catalog are exceeded and can causebreakdown of insulation and hence electricshock. If heating is allowed to continue itintensifies by further increasing the localresistance through loss of temper of springcontacts, formation of oxide film on con-tacts and wires and leakage currentsthrough carbonization of insulation andtracking paths. Fire can then result in thepresence of combustible materials and thismay release noxious fumes. Overheatingmay not be visually apparent. Burns mayresult from touching overheated compo-nents.

3. HANDLINGCare must be taken to avoid damage to any component parts of electrical con-nectors during installation and use.Although there are normally no sharpedges, care must be taken when handlingcertain components to avoid injury to fin-gers. Electrical connectors may be damagedin transit to the customers, and damagemay result in creation of hazards. Productsshould therefore be examined prior toinstallation/use and rejected if found to bedamaged.

4. DISPOSALIncineration of certain materials may releasenoxious or even toxic fumes.

5. APPLICATIONConnectors with exposed contacts shouldnot be selected for use on the current sup-ply side of an electrical circuit, because anelectric shock could result from touchingexposed contacts on an unmated connector.Voltages in excess of 30 V ac or 42.5 V dcare potentially hazardous and care shouldbe taken to ensure that such voltages can-not be transmitted in any way to exposedmetal parts of the connector body. The con-nector and wiring should be checked,before making live, to have no damage tometal parts or insulators, no solder blobs,loose strands, conducting lubricants, swarf,or any other undesired conducting particles.Circuit resistance and continuity checkshould be made to make certain that thereare no high resistance joints or spuriousconducting paths. Always use the correctapplication tools as specified in the DataSheet/Catalog. Do not permit untrained per-sonnel to wire, assemble or tamper withconnectors. For operation voltage please seeappropriate national regulations.

IMPORTANT GENERAL INFORMATION(i) Air and creepage paths/Operating volt-age. The admissible operating voltagesdepend on the individual applications andthe valid national and other applicable safe-ty regulations.For this reason the air and creepage pathdata are only reference values. Observereduction of air and creepage paths due toPC board and/or harnessing.

(ii) TemperatureAll information given are temperature lim-its. The operation temperature depends onthe individual application.

(iii) Other important informationCannon continuously endeavors to improvetheir products. Therefore, Cannon productsmay deviate from the description, technicaldata and shape as shown in this catalog anddata sheets.

“Engineered for life” is a registered trade-mark of ITT Corporation ©2006. All othertrademarks or registered trademarks areproperty of their respective owners. All datasubject to change without notice.

Product WarrantyITT Electronic Components, a Division of ITTCorporation manufactures the highest qual-ity products available in the marketplace;however these products are intended to beused in accordance with the specificationsin this publication. Any use or applicationthat deviates from the stated operatingspecifications is not recommended and maybe unsafe. No information and data con-tained in this publication shall be construedto create any liability on the part of Cannon.Any new issue of this publication shall auto-matically invalidate and supersede any andall previous issues. A limited warrantyapplies to Cannon products. Except for obli-gations assumed by Cannon under this war-ranty, Cannon shall not be liable for anyloss, damage, cost of repairs, incidental orconsequential damages of any kind,whether or not based on express or impliedwarranty, contract, negligence or strict lia-bility arising in connection with the design,manufacture, sale, use or repair of the prod-ucts. Product availability, prices and deliverydates are exclusively subject to our respec-tive order confirmation form; the sameapplies to orders based on developmentsamples delivered. This publication is not tobe construed as an offer. It is intendedmerely as an invitation to make an offer. Bythis publication, Cannon does not assumeresponsibility or any liability for any patentinfringements or other rights of third partieswhich may result from its use. Reprintingthis publication is generally permitted, indi-cating the source. However, Cannon's priorconsent must be obtained in all cases.

VEAM PT Connectors

Product Information


ca l1-l44.qxd:layout 1 2/10/11 9:01 am page 1...dp bp c d ac af 05-2330 w sealing gland † the cpt...

Documents