building sturdy sawhorsene homebuilding article · 8/24/2014 building sturdy sawhorses - fine...
TRANSCRIPT
8/24/2014 Building Sturdy Sawhorses - Fine Homebuilding Article
http://www.finehomebuilding.com/how-to-departments/building-skills/building-sturdy-sawhorses.aspx 1/5
Save up to 52%!
Give a Gift
How-To
Building Sturdy Sawhorsesby Patrick McCombe
I once had a coworker who described his favorite sawhorses as Clydesdales. It was an appropriate name since his bulletproof horses seemed as
heavy as their 1000-lb. namesake.
Another coworker had the opposite approach. He favored lightweight sawhorses made from six equal-length pieces of 2x4. He could bang a pair
together in the time it takes to roll out an extension cord.
I think the best sawhorses are a combination of these two approaches. The best design I’ve found is the easy-to-build “Stackable site-built
sawhorses” from Ty Simmons of Fort Laramie, Wyo.
I like Ty’s horses because they’re lightweight and strong, and use common materials.
You could build them with only a circular saw, but using a tablesaw for beveling the top and a sliding miter saw for cutting the legs makes the
process much easier.
Including setup, it took me about 90 minutes and cost me $50 in materials to make the pair of horses featured here.
1. Cut the legs.All legs have a compound angle on both ends. With the miter and bevel both set at 17°, cut four legs (for a pair of horses) so that the finished leg
has the same cut on both ends. Leaving the bevel setting alone, rotate the miter table to the other 17° mark on the other side of 90°, and cut the
Sign In Do Not Track
Share this with friends!
Email Facebook
Twitter Pinterest
LinkedIn Google +
Digg StumbleUpon
Reddit Tumblr
Search for services
8/24/2014 Building Sturdy Sawhorses - Fine Homebuilding Article
http://www.finehomebuilding.com/how-to-departments/building-skills/building-sturdy-sawhorses.aspx 2/5
Photo by: Ed Pirnik
other four legs.
2. Bevel the top.
Rip a 17° bevel on both sides of the top. You can do this with a circular saw, but a tablesaw with a rip
fence is faster and easier.
3. Fasten the legs.Mark the top 3 in. from the end at all four corners. Hold the leg flush to the top, and drill the pilot holes with
a twist or pilot/countersink bit. Then drive the screws. Use 11/2-in. #10 wood screws because they have
greater shear strength than deck or drywall screws. Trim one of the tops later if you want the horses to
stack.
4. Install the bracing.Mark the legs 12 in. up to locate the 1x4 leg bracing. Hold or clamp the board in place, and scribe both ends to match the leg angle. Drill the pilot
holes, and drive the screws.
8/24/2014 Building Sturdy Sawhorses - Fine Homebuilding Article
http://www.finehomebuilding.com/how-to-departments/building-skills/building-sturdy-sawhorses.aspx 3/5
5. Scribe and cut the gussets.Clamp or hold the gusset in place while you drill pilot holes. Be sure to align the drill bit carefully so that thehole stays in the center of the leg. After you run in the screws, your team of horses is ready for work.
6. Almost done.
Clamp or hold the gusset in place while you drill pilot holes. Be sure to align the drill bit carefully so that thehole stays in the center of the leg. After you run in the screws, your team of horses is ready for work.
Four more optionsConsider these alternatives when space is tight or time is short.
Site-built
8/24/2014 Building Sturdy Sawhorses - Fine Homebuilding Article
http://www.finehomebuilding.com/how-to-departments/building-skills/building-sturdy-sawhorses.aspx 4/5
Space Saver Built from 20-in. by 32-in. scraps
of 3/4-in. plywood, these clever knockdown
sawhorses are surprisingly sturdy. The 3/8-
in.-deep mortises in the 2x6 top are made
with a circular saw and a sharp chisel.
Get ‘er done Made from six 32-in. pieces of
2x4, these are the horses to build when
you’re in a hurry. You can use gun nails if
time is extra tight, but 21/2-in. screws hold
better and come apart easier when it’s time
for your steeds to become blocking.
Fast, rock solid, but expensive Trojan’s
nearly indestructible TS series is the best
commercially produced sawhorse, but you’ll
need to shell out $90 per pair for the 27-in.
version. The 35-in. model costs another $12
per pair.
A popular option Available at home centers
everywhere, these sawhorses ($60 per pair)
have selfleveling, adjustable legs that keep
the horse steady on uneven terrain, but it’s
easy to lose the leg extensions and the bolts
that secure them.
Store-bought
Photos by Rob Yagid, exept where noted.
From Fine Homebuilding 218 , pp. 88-90 March 10, 2011
WE RECOMMEND
Your CPAP is Crawling with Germs. Beam boom A dehumidifier alternative How it Works: Wall Framing
8/24/2014 Building Sturdy Sawhorses - Fine Homebuilding Article
http://www.finehomebuilding.com/how-to-departments/building-skills/building-sturdy-sawhorses.aspx 5/5
Privacy Policy | Copyright Notice | Taunton Guarantee | User Agreement | About Us | Work for Us | Contact Us | Advertise | Press Room | Customer Service | Subscriber Alert
© 2014 The Taunton Press, Inc., Part of Taunton’s Men’s Network. All rights reserved.
Here's How to Clean it.Easy Breathe
Our 8 Favorite Kitchen CountertopMaterialsReliable Remodeler
Gypboard concrete forms Buyer's Guide to Insulation: SprayFoam
EY6432 Cordless Drill