bridging mathematics and science dr. anthony s. pyzdrowski dr.. laura j. pyzdrowski (mrs. patricia...

Bridging MathematicsBridging Mathematicsand Scienceand Science

Dr. Anthony S. PyzdrowskiDr. Anthony S. Pyzdrowski

Dr.. Laura J. PyzdrowskiDr.. Laura J. Pyzdrowski

(Mrs. Patricia Neel)(Mrs. Patricia Neel)

WVCTM Conference, March 2003WVCTM Conference, March 2003

ContentsNote to UsersUnit OutlineAssessmentWeb SitesDay 1: Structure of Bridges

Girder BridgesTruss BridgesArch BridgesCantilever BridgesSuspension BridgesCable-Stayed BridgesVocabulary Words

ContentsDay 2: Structure of BridgesDay 4: Suspension and Cable-Stayed Bridges

Suspension BridgesCable-Stayed Bridges

Day 5: Beams and TrussesDeflection of a Cantilevered Beam Activity

Deflection of a Cantilevered Beam Data TableTeachers Notes

Day 6 : Deflection of a Cantilevered Beam Activity Wrap-up/extensionSample Results

ContentsDay 9: Distribution of the Load in the Supports of a Beam Bridge

Activity on the Distribution of the LoadAbout this ActivityData CollectionDistribution of the Load Data TableAssignmentUse graphing paper to make a complete graph.

Day 10: Distribution of the Load in the Supports of a Beam BridgeUse a graphing Calculator to Graph your data.Extension ExerciseDistribution of the Suspended Load Data TableQuestions to Think About

ContentsDay 11 : Distribution of the Load Activity Wrap-up

Sample ResultsDay 12: Student Truss BridgesDay 13: Deflection of a Bridge

About this ActivityData CollectionDeflection of a Beam Bridge Data TableDeflection of a Truss Bridge Data TableDeflection of an Inverted Truss Bridge Data TableUse a graphing Calculator to Graph your data.

Day 14 : Deflection of a Bridge Wrap-upSample Results

ContentsDay 15: Unit TestDay 16: Test RubricProposed Academic Standards for Science, Technology and

Mathematics Grade 7Resources

Note to Participants

*The activities in the handouts were developed to be used in theunit on bridges. Only those activities which were developedby the authors are included in the handout.

Unit OutlinePre-assignment – Students will do research by collecting pictures and information on at least three types of bridges.

Day 1:*Introduction to Bridges – Short lecture and picture presentation about bridges. Lecture will include new vocabulary words. Students will assist in classifying the six main types of bridges. Students will be given a list of websites to be used during the unit.

Day 2:*Students will be asked to read about and discuss the structure of bridges and in particular discuss the Tacoma Narrows Bridge, a structure that failed.

Unit OutlineDay 3: Student Activity: Students will construct a model bridge and explore how the construction affects safety and efficiency of materials.

Day 4:*Activity recap and short lecture about Suspension and Cable-Stayed Bridges and three kinds of Forces – Tensile, Compressive and Shear Force.

Day 5:*Short lecture on beams and trusses. Group Hands-on-activity introducing the concept of deflection. Students will set up the apparatus, collect and record data during class. As an assignment, students will make a graph. They will model the data in a table, then on a graph.

Unit OutlineDay 6:*Activity wrap-up. Students will discuss the mathematics (linear relationship) between defection and force.

Day 7: Short lecture on strength of materials. Student activity to test for strong shapes, and lamination. Students will set up the apparatus, collect and record data during class. As an assignment, students will make a graph by plotting their results.

Day 8: Activity wrap-up. Students will discuss the mathematics involving the lamination activity.

Unit OutlineDay 9:*Activity on the distribution of the load in the supports of a beam bridge. Students will set up the apparatus, collect and record data during class. As an assignment, students will make a graph by plotting their results.

Day 10:* Students will use the graphing calculator to graph and analyze their data. Students will perform an extension exercise.

Day 11:* Activity wrap-up. Students will discuss the mathematics involved in the Beam activity.

Day 12:* Students will construct a Truss Bridge.

Unit OutlineDay 13:* Activity on the deflection of a beam and truss bridges. Students will set up the apparatus, collect and record data during class. As an assignment, students will make a graph by plotting their results.

Day 14:* Activity wrap-up. Students will discuss the mathematics involved in the Truss Bridge. Unit Review.

Day 15:* Unit Test.

Day 16:* Test Rubric.

Six Main Types of Bridges

(1) girder bridges,

(2) truss bridges,

(3) arch bridges,

(4) cantilever bridges,

(5) suspension bridges, and

(6) cable-stayed bridges.

Girder Bridgeswhich include many highway bridges, are made of beams calledgirders whose ends simply rest on piers or abutments.The span length of girder bridges ranges up to 1,000 feet (300 meters)

Truss Bridgesare supported by frameworks called TRUSSES. The parts of thetrusses are arranged in the form of triangles. Such bridges are builtover canyons, rivers, and other areas. A truss bridge may have amain span that extends more than 1,000 feet (300 meters).The simplest truss consists of three parts fastened together at theirends to form a triangle.

Arch Bridgesare structures in which each span forms an arch. The spans rangeup to about 1,700 feet (518 meters) long. The arch bridge is oneof the oldest types of bridges. Early arch bridges consisted oflarge stone blocks wedged together to form an arch.

Cantilever Bridgesconsist of two independent beams called CANTILEVERS that extendfrom opposite banks of a waterway. The two cantilevers are joinedtogether above the middle of the waterway by a beam, girder, or truss.Cantilever bridges may have spans as along as about 1,800 feet(549 meters). Many cantilever bridges have truss frameworks.(Picture by Scott M. Kozel)

Suspension Bridgesare perhaps the most impressive type of bridge because of theirlong main span and especially attractive appearance. Thesebridges have a roadway that hangs from steel cables that aresupported by two high towers. Most suspension bridges have amain span more than 1,000 feet (300 meters) long. Some have amain span longer than 4,000 feet (1,200 meters). (Picture by Scott M. Kozel)

Cable-Stayed Bridgesare different from suspension bridges, their cables are more tautthan the flexible cables of suspension bridges. They offer greaterstiffness over that of suspension bridges. Cable-stayed bridges areeconomical for medium span applications in the 500 feet(150 meters) to 3,000 feet (900 meters) range. (Photograph by Steven Richman)

Day 12: Student Truss Bridges

Students will be given a Ziploc bag with the following contents:

30 popsicle sticks (hole drilled at each end)9 lollipop sticks – 4 in.9 straws – 3 in. length9 rubber bands1 3 x 16 in piece of balsa wood

Day 12: Student Truss BridgesStudents will see a completed truss bridge and construct onelike the model.

When the bridges are completed, students will compare the models.

Day 13: Deflection of a Bridge Activity

About this Activity In this activity, you will learn how the addition of a trussstructure affects the deflection. You will also explore trussesthat are attached above and below a beam bridge. You willcollect and then record data in tables in order help answerquestions about truss bridges


Presentation Note

From the Day 9: Distribution of the Load in the Supports of a Beam Bridge Activity

“Begin your activity by setting up your beam bridge model.Mark the balsa wood 2.8m. in from one end with a ball point pen. ( This is position “0" and will be placed on one support.) Continue to mark the wood in 4 cm. intervals labeling each position through position 10.( Position “10" will be placed over the second support.)”


Data Collection Make sure you have the following:1 - Truss Bridge Model from the Truss Bridge Activity1 - Metric Ruler Several Mass Weights ( approximately 100g each)2 - Pencils or Pens to use as supports between supports and balsa wood.2 - Wooden Block Supports


Begin your activity by using only the beam bridge model portionof the truss bridge.You need to span two block supports with the balsa wood.Make sure that you place position “0” of the balsa wood over onesupport and position “10” over the other.


Mass Height Height Deflection(g) w/o mass with mass (cm.)

(cm.) (cm.)

Place a mass weight in the center of the beam bridge and record themass, height without the mass, and deflection in the table below.Continue collecting data by adding enough mass until you haveentries for 6 positions in your table.


Deflection of a Beam Bridge Data Table


(cm.) (cm.)0 6.0 6.0 0.0

125 6.0 5.5 0.5250 6.0 5.0 1.0375 6.0 4.6 1.4500 6.0 3.8 2.2625 6.0 3.4 2.6


Repeat the data collection for the truss bridge.Use the same mass entries as those in the first table.



(cm.) (cm.)

Place a mass weight in the center of the truss bridge and record themass, height without the mass, and deflection in the table below.Continue collecting data by adding enough mass until you haveentries for 6 positions in your table.


Deflection of a Truss Bridge Data Table

mass height height deflection(g.) w/o mass with mass (cm.)

(cm.) (cm.)0 12.50 12.50 0.00

125 12.50 12.40 0.10250 12.50 12.30 0.20375 12.50 12.20 0.30500 12.50 12.15 0.35625 12.50 12.10 0.40


Repeat the data collection for the inverted truss bridge.Use the same mass entries as those in the first table.



(cm.) (cm.)

Place a mass weight in the center of the inverted truss bridge and record the mass, height without the mass, and deflection in thetable below. Continue collecting data by adding enough mass until you have entries for 6 positions in your table.


Deflection of a Truss Bridge Data Table

mass height height deflection(g.) w/o mass with mass (cm.)

(cm.) (cm.)0 12.70 12.70 0.00

125 12.70 12.60 0.10250 12.70 12.55 0.15375 12.70 12.50 0.20500 12.70 12.50 0.20625 12.70 12.45 0.25


QuestionsExplain how a truss structure affects the deflection of a bridge.

Does there seem to be a difference in the deflection between the non-inverted and inverted truss bridge?


Use a graphics calculator to graph your data

1.Turn on your graphics calculator, Select MODE arrow down to Float and use the right arrow to highlight 5 and ENTER press 2nd QUIT when done.


To Enter your Data from a Table:

2. Select LIST3. Use the arrow keys to highlight L1 and select

CLEAR, ENTER4. Use the arrow keys to highlight L2 and select

CLEAR, ENTER5. Move to the first cell under L1 and enter your mass

data.6. Select the right arrow key to move to L2, and enter

your data for deflection of a beam bridge . Press 2nd QUIT when done.


To Turn on a Plot:

7. Select 2nd PLOT and use the arrow keys to highlight 1.8. Select ENTER9. Using the arrow keys and the ENTER key, make sure

that Plot 1 is turned On, and choose to make a Scatter Plot. By default, Xlist is L1 and Ylist is L2. Choose any Mark type that you wish.

10. Select and make sure all other plots are turned off ( use steps 8 and 9 above if necessary.) Press 2nd QUIT when done.


To See a Plot:

11. Press Y= and use CLEAR and the arrow keys to clear old equations.

12. Press GRAPH, ZOOM and the select 7 to see all of the points from your table.


To Make a Manual Fit Line:13. Select 2nd STAT, CALC and select 3 for Manual-Fit .14. Move the cursor to the upper right to begin your fit line

and select ENTER to tie down a point on the line. 15. Using the arrow keys continue the line segment and then

select ENTER to tie down the second point; your manual-fit line is drawn.

16. What is the equation of the line of manual-fit? y =(as it appears on your calculator screen.)17. You may move the arrow keys to move the line until you

select ENTER .


To Make a Fit Line Using a Linear Regression:

18. Select 2nd STAT, CALC and select 5 for a Linear Regression.

19. Select 2nd VARS select 2, 1, ENTER to place your fit equation into the Y1 equation.

20. a = b = 21. Select Y=


22. What is the equation of the line of best fit? Y1 = (as it appears on your calculator screen.)23. What is the y-intercept of the line of best fit?24. What is the slope of the line of best fit?25. What does x represent in this problem?26. Which number values make sense for x and why?27. What does y represent in this problem?28. Which number values make sense for y and why?30. Select GRAPH


Repeat the process for the truss bridge data using Lists 1 and 3 for StatPlot2 and the inverted truss bridge data using Lists 1 and 4 and StatPlot 3. ( Skip the manual fit.)

If you look carefully, you should see three scatter plots in your viewing window. Use them to answer the following:A) If the mass is constant, is there a significant difference in deflection between a truss that is above or one that is below the beam bridge? Explain.B)How does the use of a truss affect the deflection of a beam bridge? Explain.

bridging mathematics and science dr. anthony s. pyzdrowski dr.. laura j. pyzdrowski (mrs. patricia...

Documents

structure of bridges

contents day

student truss bridges

unit outline day

unit test day

bridges short lecture

beam bridge activity

bridges vocabulary words