bradley s19 310ss16
DESCRIPTION
Bradley Safety ShowerTRANSCRIPT
S19-310SS16Combination Drench Shower/Eyewash Unit
© 2012 BradleyP.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 800.BRADLEY (800.272.3539) Fax: 262.251.5817bradleycorp.com
Page 1 of 3This information is subject to change without notice. 2/10/2012
Emergency Fixtures Document No. 4565
• Complies with American National Standard Z358.1• All Stainless Steel• Combination Units may be Top-Supplied or Mid-Supplied• Universal Identification Sign and Inspection Tag Included• Full, One-Year Warranty• Patent Pending• Classified by Underwriters Laboratory Inc. to ANSI Z358.1
SpecificationsCombination Drench Shower and Eyewash Unit saves space and fits easily into any work environment. Shower valve operates quickly by a pull rod with a triangular handle. Shower provides a superior washdown with a more even spray pattern. Eyewash operated by a large, highly visible push handle. Safe, steady water flow under varying water supply conditions from 30–90 PSI is assured by integral flow control in the sprayhead assembly. NOTE: The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a minimum 30 PSI flowing pressure.
This plumbing fixture is not intended to dispense water for human consumption through drinking or for preparation of food or beverages.
®
Recommended Option:Navigator S19-2100 EFX25
Emergency Thermostatic Mixing Valve
Satisfies ANSI Z358.1tepid water requirements.
Model Description S19-310 Drench Shower and Eyewash - All Type 16 Stainless Steel Unit
S19-2100 Navigator EFX25 - Emergency Thermostatic Mixing Valve
S19-310SS16Combination Drench Shower/Eyewash Unit
© 2012 BradleyP.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 800.BRADLEY (800.272.3539) Fax: 262.251.5817bradleycorp.com
Page 2 of 3This information is subject to change without notice. 2/10/2012
Emergency Fixtures Document No. 4565
Eyewash Bowl10¾" (273mm) diameter type 316 corrosion-resistant stainless steel.
Standard Sprayhead AssemblyType 316 corrosion-resistant stainless steel sprayhead with twin soft-flow eyewash heads and protective sprayhead covers. Safe, steady water flow under varying water supply conditions from 30–90 PSI is assured by integral flow control in the sprayhead assembly.
Shower ValveType 316 corrosion-resistant stainless steel 1" NPT stay-open ball valve. Operated by a type 316 stainless corrosion-resistant steel pull rod with triangular handle.
Eyewash ValveType 316 corrosion-resistant stainless steel ¼" NPT stay-open ball valve. Hand operated by highly visible type 316 corrosion-resistant stainless steel push handle or foot treadle.
Pipe and FittingsType 316 corrosion-resistant stainless steel.
Water Supply1¼" NPT.
Local codes may require the installation of a backflow prevention valve to complete proper installation. Compliance with local codes is the responsibility of the installer. Valve must be tested annually to verify that it is functioning properly. Backflow prevention valves are not included with the fixture and may be supplied by the contractor or purchased from Bradley Corporation.
SpinTec Flow Rate vs Inlet Pressure at Fixture
0
5
10
15
20
25
30
35
0 10 20 30 40 50 60 70 80 90
Inlet pressure at Fixture (psig)
Flow
Rat
e (g
pm)
Standard EquipmentSpinTec™ ShowerheadHigh performance type 316 corrosion-resistant stainless steel showerhead measures 2" (51mm) in diameter. SpinTec drench showerhead features integral 26 GPM flow control, conserving water and helping to accurately size your tepid water system.
S19-310SS16Combination Drench Shower/Eyewash Unit
© 2012 BradleyP.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 800.BRADLEY (800.272.3539) Fax: 262.251.5817bradleycorp.com
Page 3 of 3This information is subject to change without notice. 2/10/2012
Emergency Fixtures Document No. 4565
265⁄8" (676mm)
3¾" (95mm)
86¾"(2203mm) to Bottom
of Base
9"(229mm)
65½"(1664mm) to Bottom
of Base
36¾" (933mm) to Bottom
of Base
6"(152mm)
Ø 2"(51mm)
42¼" (1073mm) to Bottom
of Base
683⁄8" (1737mm) to Bottom
of Base
94" (2388mm) to Bottom
of Base
Ø 9" (229mm) Flange with (3) Ø 3⁄8" (10mm) Holes on Ø 8" (203mm)
Bolt Circle
Top view from bowl
Ø 10¾"(273mm)
10¼" (260mm)
9" (229mm)
All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1⁄8" (3mm) per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 1⁄8" (3mm).