bpn-sas2-216el1/el2 backplane · taiwan (r.o.c) tel: +886-(2) 8226-3990 fax: +886-(2) 8226-3992...

BPN-SAS2-216EL1/EL2 BACKPLANE

USER’S MANUAL

1.0d

ii

BPN-SAS2-216EL1/EL2 Backplane User's Guide

Manual Revision 1.0d Release Date: June 26, 2015

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not exceed the price paid for the hardware product. California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document.

Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2015 by Super Micro Computer, Inc. All rights reserved. Printed in the United States of America

iii

Preface

Table of Contents

Contacting Supermicro ........................................................................................v Returning Merchandise for Service....................................................................vi Overview of the BPN-SAS2-216EL1/EL2 Backplanes ..................................... vii

Chapter 1 Safety Guidelines1-1 ESD Safety Guidelines ................................................................................... 1-1

1-2 General Safety Guidelines .............................................................................. 1-11-3 An Important Note to Users ............................................................................ 1-21-4 Introduction to the BPN-SAS2-216EL1/EL2 Model Backplane....................... 1-2

Chapter 2 Connectors, Jumpers and LEDs2-1 Connectors ...................................................................................................... 2-12-2 FrontConnectorandPinDefinitions ............................................................... 2-2

2-3 Jumper Locations and Settings....................................................................... 2-3Explanation of Jumpers .................................................................................. 2-3

2-4 Front Connectors and LED Indicators ............................................................ 2-6

Chapter 3 Dual Port and Cascading Configurations3-1 Single and Dual Port Expanders..................................................................... 3-1

Single Ports ..................................................................................................... 3-1Dual Ports ....................................................................................................... 3-1

3-2 Failover ............................................................................................................ 3-2Single Host Bus Adapter ................................................................................. 3-2Single Host Bus Adapter Failover ................................................................... 3-2

3-3 Failover with RAID Cards and Multiple HBAs ................................................ 3-3Dual Host Bus Adapter .................................................................................. 3-3Dual Host Bus Adapter Failover...................................................................... 3-3

3-4 Chassis Power Card and Support Cables ...................................................... 3-4Chassis Power Card ....................................................................................... 3-4Connectioning an Internal Host Bus Adapter to the Backplane .................... 3-5Supported Internal HBA Cables ...................................................................... 3-5Connecting an External Host Bus Adapter to the Backplane ........................ 3-7Single External Host Bus Adapter ................................................................. 3-7Dual External Host Bus Adapter .................................................................... 3-7Supported External HBA to Backplane Cable ................................................ 3-8Connecting Multiple Backplanes in a Single Channel Environment ............... 3-9SingleHBAConfigurationCables ................................................................. 3-10Connecting Multiple Backplanes in a Dual Channel Environment ................3-11

iv


DualHBAConfigurationCables .................................................................... 3-123-5 SupportedCascadingConfigurations ........................................................... 3-13

Server System with Single SAS HBA ........................................................... 3-14DualSASHBAandCascadedConfiguration ............................................... 3-15DualSASHBAandCascadedConfigurationwithBranching ...................... 3-16

v

Preface

Contacting Supermicro

HeadquartersAddress: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Website: www.supermicro.com

EuropeAddress: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Website: www.supermicro.nl

Asia-PacificAddress: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Email: [email protected]

Website: www.supermicro.com.tw

vi


Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-fore any warranty service will be rendered. You can obtain service by calling your vendor for a Returned Merchandise Authorization (RMA) number. When returning to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling charges will be applied for all orders that must be mailed when service is complete.

For faster service, RMA authorizations may be requested online (http://www.supermicro.com/support/rma/).

Whenever possible, repack the backplane in the original Supermicro box, using the original packaging materials. If these are no longer available, be sure to pack the backplane in an anti-static bag and inside the box. Make sure that there is enough packaging material surrounding the backplane so that it does not become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages in-curred in shipping or from failure due to the alteration, misuse, abuse or improper maintenance of products.

Duringthewarrantyperiod,contactyourdistributorfirstforanyproductproblems.

vii

Preface

Overview of the BPN-SAS2-216EL1/EL2 Backplanes

The BPN-SAS2-216EL1/EL2 model backplanes consists of a BPN-SAS2-216EB backplane (A) with one or two SAS2-216EL daughter cards (B and C) mounted on the rear of the backplane.

The BPN-SAS2-216EL1 model consists of the BPN-SAS2-216EB backplane (A) and one BPN-SAS2-216EL daughter card (B), mounted on the right-hand side of the backplane.

The BPN-SAS2-216EL2 model consists of the BPN-SAS2-216EB backplane (A), and two BPN-SAS-216EL daughter cards (B and C), mounted on the rear of the backplane.

Components on the front side of the BPN-SAS2-216EB backplane include twenty-four SAS connectors and their respecitve activity and failure LEDs. Components on the rear side of the backplane include jumpers and power and fan connectors. Thedaughtercard'scomponentsincludeSASports,flashandexpanderchips,andmode select jumpers.

SAS2-216EL Daughter Card (C)

SAS2-216EB Backplane (A)

SAS2-216EL Daughter Card (B)

Rear Side of the Backplane

Front Side of the Backplane

Figure C-1: Overview of the BPN-SAS2-216EL1/EL2 Backplane

viii


Notes

1-1

Chapter 1 Safety Guidelines

Chapter 1

Safety Guidelines

To avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components.

1-1 ESD Safety Guidelines

Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to your system, it is important to handle the backplane very carefully. The following measures are generally sufficient to protect your equipment from ESD.•Use a grounded wrist strap designed to prevent static discharge.

•Touch a grounded metal object before removing a component from the antistatic bag.

•Handle the backplane and daughter cards by their edges only; do not touch the components, peripheral chips, memory modules or gold contacts.

•When handling chips or modules, avoid touching their pins.

•Put the backplane and peripherals back into their antistatic bags when not in use.

1-2 General Safety Guidelines

•Always disconnect power cables before installing or removing any components from the computer, including the backplane.

•Disconnect the power cable before installing or removing any cables from the backplane.

•Make sure that the backplane is securely and properly installed on the mother-board to prevent damage to the system due to power shortage.

1-2


1-3 An Important Note to Users

All images and layouts shown in this user's guide are based upon the latest PCB Revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this manual.

1-4 Introduction to the BPN-SAS2-216EL1/EL2 Backplane

The BPN-SAS2-216EL1/EL2 model backplane has been designed to utilize the most up-to-date technology available, providing your system with reliable, high-quality performance.

ThismanualreflectstheBPN-SAS2-216ELRevision1.02backplane,themostcur-rent release available at the time of publication.

This manual also describes the SAS2-216EL daughter card, Revision 1.02, the most current release available at the time of publication. Always refer to the Supermicro website at www.supermicro.com for the latest updates, compatible parts and sup-portedconfigurations.

2-1

Chapter 2 Connectors, Daughter Cards, Jumpers and LEDs

Chapter 2

Connectors, Jumpers and LEDs

2-1 Connectors

Connectors

1. Flash Chip

2. Expander Chip

3. SAS Port: PRI_J1

4. SAS Port: PRI_J2

5. SAS Port: PRI_J3

Figure 2-1: Connectors on the Backplane and Daughter Cards

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:

BPN-SAS2-216ELMACH FINISH

30ANGLE

SPECIFIED DIMENSIONSUNLESS OTHERWISE

XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES

Minh Hong/MaxDESIGNER:

DATE: 12/03/2009

PROJECT NAME:SAN JOSE,CA 95131

DESIGNED BY SUPERMICRO U.S.A.www.supermicro.com

TEL:408-503-8000 FAX:408-503-8008

SILKSCREENPRIMARY-SIDESUPER

RSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERSUPERRRRRRRRRRR

A

A

DESIGNED IN USA

Rev:1.02BPN-SAS2-216EL

J25

2 6463 J24

2 6463

U2Q5

1

BUZZER_ENB1

1

REMOTE_FAN_FAIL2

1

REMOTE_FAN_FAIL1

OVERH

EATFAIL1

A C

FAN

FAIL1

A

C

5V_LED1

AC

12V_LED1

AC

F2

F1

+

EC25

+ EC23

+

EC22

+

EC19

+

EC17

+

EC9

+

EC8

+

EC7

+

EC6

+

EC5

+

EC4+

EC3

+

EC24

+

EC21

+

EC20

+

EC2

+

EC18

+

EC16

+

EC15

+

EC14

+

EC13

+

EC12

+

EC11

+

EC10

+

EC1

P1

B1

A1 A15

B15

A29

B29

A43 A56

B56B43P2 B1

A1 A15

B15

A29

B29

A43 A56

B56B43

U3

F7 F4F11 F10

41

FAN1

41

FAN2

4

1

FAN3

PRI_I2C

BUZZER1

+

R14

R16R17 R19

BPN-SAS2-216EBREV: 1.02

DESIGNED IN USA

BAR CODE

RRRRRRRRRR

UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERS UPERSR

UPERS SECONDARY-SIDESILKSCREEN

TEL:408-503-8000 FAX:408-503-8008

www.supermicro.comDESIGNED BY SUPERMICRO U.S.A.

SAN JOSE,CA 95131PROJECT NAME:

2009.12.03DATE:

DESIGNER: Ben/Minh

ARE IN INCHES

DECIMALTOLERANCES

.1

.03

.010

XXXXXX

UNLESS OTHERWISESPECIFIED DIMENSIONS

ANGLE30

MACH FINISHBPN-SAS2-216EB

REV: 1.02

+5V+12V

GN

DG

ND

PWR1

+5V +12VGND GND

PWR2

+5V +12VGND GND

PWR3

+5V +12VGND GND

PWR4

17

11

Rear of BPN-SAS2-261EB Backplane

Front of BPN-SAS2-2l6EL Daughter Card(s)

12131415

16 19

1717 1818

18

110

18

6. EPP Connectors: J2

7. Fan Connectors: Fan1, Fan2, and Fan3

8. Power Connectors: PWR1 - PWR4

9. Debug Connector: EXPDBG1

10. UART Connector: SMART_UART

2-2


2-2 FrontConnectorandPinDefinitions

BackplaneMain Power

4-Pin Connector

Pin#Definition

1 +12V

2 and 3 Ground

4 +5V

8. Backplane Main Power Connectors

The 4-pin connectors are designated PWR1, PWR2, PWR3 and PWR4. They provide power to the backplane. See the tableontherightforpindefinitions.

7. Fan Connectors

The 3-pin connectors, designated FAN1, FAN2, and FAN3, provide power to the fans. Seethetableontherightforpindefinitions.

Fan Connectors

Pin#Definition

1 Ground

2 +12V

3 Tachometer

2. Expander Chips

This expander chip allows the backplane to support dual ports, cascading, and failover.

1. Flash Chips

The flash chip enhances the backplanememory.

3. - 5. SAS Ports

The primary and secondary sets of SAS ports provide expander features including cascading and failover. From right to left the ports are Primary 1,2,3 and Second-ary 1,2,3.

6. EPP Ports

The EPP ports are used for manufacturer diagnostic purposes only.

9. Debug Connector

The debug connector is designated EX-PDBG1 and is used for manufacturer's diagnostic purposes only.

10. UART Connector

The UART connector is designated SMART_UART and is used for manufac-turer's diagnostic purposes only.

2-3


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


2-3 Jumper Locations and Settings

Explanation of JumpersTo modify the operation of the backplane, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified witha square solder pad on the printed circuit board. Note: On two pin jumpers, "Closed" means the jumper is on and "Open" means the jumper is off the pins.

ConnectorPins

Jumper

Setting

3 2 1

3 2 1

J25

2 6463 J24

2 6463

U2Q5

1

BUZZER_ENB1

1

REMOTE_FAN_FAIL2

1

REMOTE_FAN_FAIL1

OVERH

EATFAIL1

A C

FAN

FAIL1

A

C

5V_LED1

AC

12V_LED1

AC

F2

F1

+

EC25

+ EC23

+

EC22

+

EC19

+

EC17

+

EC9

+

EC8

+

EC7

+

EC6

+

EC5

+

EC4

+

EC3

+

EC24

+

EC21

+

EC20

+

EC2

+

EC18

+

EC16

+

EC15

+

EC14

+

EC13

+

EC12

+

EC11

+

EC10

+

EC1

P1

B1

A1 A15

B15

A29

B29

A43 A56

B56B43P2 B1

A1 A15

B15

A29

B29

A43 A56

B56B43

U3

F7 F4F11 F10

41

FAN1

41

FAN2

4

1

FAN3

PRI_I2C

BUZZER1

+

R14

R16R17 R19


DESIGNED IN USA

BAR CODE

RRRRRRRRRR



TEL:408-503-8000 FAX:408-503-8008



2009.12.03DATE:

DESIGNER: Ben/Minh

ARE IN INCHES

DECIMALTOLERANCES

.1

.03

.010

XXXXXX


ANGLE30


REV: 1.02

+5V+12V

GN

DG

ND

PWR1

+5V +12VGND GND

PWR2

+5V +12VGND GND

PWR3

+5V +12VGND GND

PWR4

J25

2 6463 J24

2 6463

U2Q5

1

BUZZER_ENB1

1

REMOTE_FAN_FAIL2

1

REMOTE_FAN_FAIL1

OVERH

EATFAIL1

A C

FAN

FAIL1

A

C

5V_LED1

AC

12V_LED1

AC

F2

F1

+

EC25

+ EC23

+

EC22

+

EC19

+

EC17

+

EC9

+

EC8

+

EC7

+

EC6

+

EC5

+

EC4

+

EC3

+

EC24

+

EC21

+

EC20

+

EC2

+

EC18

+

EC16

+

EC15

+

EC14

+

EC13

+

EC12

+

EC11

+

EC10

+

EC1

P1

B1

A1 A15

B15

A29

B29

A43 A56

B56B43P2 B1

A1 A15

B15

A29

B29

A43 A56

B56B43

U3

F7 F4F11 F10

41

FAN1

41

FAN2

4

1

FAN3

PRI_I2C

BUZZER1

+

R14

R16R17 R19


DESIGNED IN USA

BAR CODE

RRRRRRRRRR



TEL:408-503-8000 FAX:408-503-8008



2009.12.03DATE:

DESIGNER: Ben/Minh

ARE IN INCHES

DECIMALTOLERANCES

.1

.03

.010

XXXXXX


ANGLE30


REV: 1.02

+5V+12V

GN

DG

ND

PWR1

+5V +12VGND GND

PWR2

+5V +12VGND GND

PWR3

+5V +12VGND GND

PWR4

REMOTE_FAN_FAIL1REMOTE_FAN_FAIL2

BUZZER_ENB1

Figure2-2:JumperLocationsandPinDefimitions

PRI_MODE1

PRI_MODE2

Rear of BPN-SAS2-261EB Backplane

Front of BPN-SAS2-2l6EL Daughter Card

2-4


General Jumper Settings

Jumper Jumper Settings Note

PRI_MODE1 Pins 2-3 Factory setting, do not change

PRI_MODE2 Pins 2-3 Factory setting do not change

REMOTE_FAN_FAIL1 Open: Enable (Default)Closed: Disable

Enables/disables the fan speed reporting.

REMOTE_FAN_FAIL2 Open: Enable (Default)Closed:Disable Enables/disables the FANFAIL1 LED

BUZZER_ENB1 Open: DisableClosed: Enable Buzzer enable*

*The buzzer sound indicates that a condition requiring immediate attention has occurred.

The buzzer alarm is triggered by any of the following conditions:

1. Hard drive failure

2. Fan failure

3. System temperature over 45º Celsius.

Early versions of Supermicro SAS2 backplanes come equipped with a buzzer. New versions of these backplanes no longer support a buzzer. We recommend using the LSI MegaRAID Storage Manager or a similar management application to trigger an email alert instead.

2-5


Rear LEDs

LED Fail State Specification

12V_LED1 Off Green LED indicates backplane 12V power. Light is on during normal operation.

5V_LED1 Off Blue LED indicates backplane 5V power. Light is on during normal operation.

FANFAIL1 On Red LED indicates a fan failure. Light is off during normal operation

OVERHEATFAIL1 On Red LED indicates an overheat condition. Light is off dur-ing normal operation

J252 64

63 J24

2 6463

U2Q5

1

BUZZER_ENB1

1

REMOTE_FAN_FAIL2

1

REMOTE_FAN_FAIL1

OVERH

EATFAIL1

A C

FAN

FAIL1

A

C

5V_LED1

AC

12V_LED1

AC

F2

F1

+

EC25

+ EC23

+

EC22

+

EC19

+

EC17

+

EC9

+

EC8

+

EC7

+

EC6

+

EC5

+

EC4

+

EC3

+

EC24

+

EC21

+

EC20

+

EC2

+

EC18

+

EC16

+

EC15

+

EC14

+

EC13

+

EC12

+

EC11

+

EC10

+

EC1

P1

B1

A1 A15

B15

A29

B29

A43 A56

B56B43P2 B1

A1 A15

B15

A29

B29

A43 A56

B56B43

U3

F7 F4F11 F10

41

FAN1

41

FAN2

4

1

FAN3

PRI_I2C

BUZZER1

+

R14

R16R17 R19


DESIGNED IN USA

BAR CODE

RRRRRRRRRR



TEL:408-503-8000 FAX:408-503-8008



2009.12.03DATE:

DESIGNER: Ben/Minh

ARE IN INCHES

DECIMALTOLERANCES

.1

.03

.010

XXXXXX


ANGLE30


REV: 1.02

+5V+12V

GN

DG

ND

PWR1

+5V +12VGND GND

PWR2

+5V +12VGND GND

PWR3

+5V +12VGND GND

PWR4 5V_LED1OVERHEATFAIL1

FANFAIL1 12V_LED1

Figure 2-3: Rear LEDs

2-6


2-4 Front Connectors and LED Indicators

Front SAS/SATA Connectors

FrontConnector

SAS Drive Number

FrontConnector

SAS Drive Number

SAS #J0 SAS/SATA HDD #1 SAS #J12 SAS/SATA HDD #13












U1

FAIL9A C

FAIL8

A C

FAIL7

A C

FAIL6

A C

FAIL5

A C

FAIL4

A C

FAIL3

A C FAIL23A C

FAIL22A CFAIL21

A C

FAIL20

A CFAIL2

A C FAIL19A C

FAIL18A C

FAIL17

A C

FAIL16

A C

FAIL15

A C

FAIL14

A C

FAIL13

A C

FAIL12C

FAIL11

A C

FAIL10

A C

FAIL1

A C

ACT9A C

ACT8

A C

ACT7

A C

ACT6

A C

ACT5

A C

ACT4

A C

ACT3

A C ACT23A C

ACT22A CACT21

A C

ACT20

A CACT2

A C ACT19A C

ACT18

A C

ACT17A

CACT16A C

ACT15

A C

ACT14

A C

ACT13

A C

ACT12A C

ACT11

A C

ACT10A

C

ACT1

A C

ACT0A C

FAIL0A C

C65

J7

22

2133

27

8

9

J6

22

2133

27

8

9

J5

22

2133

27

8

9

J0

22

2133

87

9

J1

22

2133

27

8

9

J10

22

2133

27

8

9

J11

22

2133

27

8

9

J12

22

2133

27

8 9

J13

22

2133

27

8 9

J14

22

21

3327

8 9

J15

22 2133

27

87

9

J16

22

2133

87

9

J17

22

2133

87

9

J18

22

21

87

9

J19

22

2133

87

9

J2

22

2133

27

8

9

J20

22

2133

87

9

J21

22

2133

87

9

J9

22

2133

27

8

9

J8

22

2133

27

8

9

J4

22

2133

27

8

9

J3

22

2133

27

8

9

J22

22

21338

7

9

J23

22

2133

27

87

9

R38

R40

R8

RRRRRRRRRR


UPERS PRIMARY-SIDESILKSCREEN

TEL:408-503-8000 FAX:408-503-8008



2009.12.03DATE:

DESIGNER: Ben/Minh

ARE IN INCHES

DECIMALTOLERANCES

.1

.03

.010

XXXXXX


ANGLE30


REV: 1.02

MH9

MH7

MH5

MH4

MH2

MH12 MH11 MH10

MH1 MH3 MH6 MH8SAS

#J0

SAS

#J1

SAS

#J2

SAS

#J3

SAS

#J4

SAS

#J5

SAS

#J6

SAS

#J7

SAS

#J8

SAS

#J9

SAS

#J10

SAS

#J11

SAS

#J12

SAS

#J13

SAS

#J14

SAS

#J15

SAS

#J16

SAS

#J17

SAS

#J18

SAS

#J19

SAS

#J20

SAS

#J21

SAS

#J22

SAS

#J23

AC

T #2

3, F

AIL

#23

AC

T #2

2, F

AIL

#22

AC

T #2

1, F

AIL

#21

AC

T #2

0, F

AIL

#20

AC

T #1

9, F

AIL

#19

AC

T #1

8, F

AIL

#18

AC

T #1

7, F

AIL

#17

AC

T #1

6, F

AIL

#16

AC

T #1

5, F

AIL

#15

AC

T #1

4, F

AIL

#14

AC

T #1

3, F

AIL

#13

AC

T #1

2, F

AIL

#12

AC

T #1

1, F

AIL

#11

AC

T #1

0, F

AIL

#10

AC

T #9

, FA

IL#9

AC

T #8

, FA

IL#8

AC

T #7

, FA

IL#7

AC

T #6

, FA

IL#6

AC

T #5

, FA

IL#5

AC

T #4

, FA

IL#4

AC

T #3

, FA

IL#3

AC

T #2

, FA

IL#2

AC

T #1

, FA

IL#1

AC

T #0

, FA

IL#0

Figure 2-4: Front Connectors and LEDs

2-7


Front LED Indicators

Front LED Hard Drive Activity Failure LEDSAS #J0 ACT #0 FAIL #0

SAS #J1 ACT #1 FAIL #1























2-8


Notes

3-1

Chapter 3 Dual Port and Cascading Configurations

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


Port B Secondary Ports Expander 2

From HBA or higher backplane



To Lower Backplane in Cascaded System


Port A Primary Ports Expander 1

Chapter 3

DualPortandCascadingConfigurations

3-1 Single and Dual Port Expanders

Single PortsBPN-SAS2-216EL1 model backplanes have a single-port expander on the daughter card that accesses all of the drives and supports cascading.

Figure3-2:BPN-SAS2-216EL2DualPortConfiguration

J3 J3

J2J1 J1

J2


Dual PortsBPN-SAS2-216EL2 model backplanes have dual-port expanders on the daughter cards that access all of the hard drives. These dual-port expanders support cascad-ing, failover, and recovery.

J3

J2

J1

Port A Primary Ports Expander 1

Figure3-1:BPN-SAS2-216EL1SinglePortConfiguration

3-2


Single Host Bus AdapterIn a single host bus configuration, thebackplane connects to one Host Bus Adapter (HBA).

The BPN-SAS2-216EL2 model backplane has two expanders which enable effec-tive failover and recovery.

3-2 Failover

Port A Expander 1

Port B Expander 2

Single Host Bus Adapter Failover

If the expander or data path in Port A fails, the system automatically switches to Port B.

Figure 3-4: Single HBA Failover

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCKP_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


SAS HBA

Port A Expander 1

Port B Expander 2

Figure 3-3: Single HBA

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


SAS HBA

3-3


Port A Expander 1

Port B Expander 2

Dual Host Bus Adapter In a dual host bus configuration, thebackplane connects to two HBAs.

Figure 3-5: Dual HBA

Dual Host Bus Adapter Failover

If the expander or data path in Port A fails, the system automatically switches to Port B. This maintains a full connec-tion to all drives.

Figure 3-6: Dual HBA Failover

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


SAS HBA

SAS HBA

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


SAS HBA

SAS HBA

Port A Expander 1

Port B Expander 2

IMPORTANT: For RAID controllers, redundancy is achieved through port failover. For multiple HBAs MPIO software is required to achieve failover protection.

3-3 Failover with RAID Cards and Multiple HBAs

TheBPN-SAS2-216ELbackplanemaybeconfiguredforfailoverwithmultipleHBAsusing either RAID controllers or HBAs to acheive failover protection.

RAID Controllers: If RAID controllers are used, then the failover is accomplished through port failover on the same RAID card.

HBAs: If multiple HBAs are used to achieve failover protection and load balancing, LinuxMPIOsoftwaremustbe installedandcorrectlyconfiguredtoperformthe load balancing and failover tasks.

3-4


3-4 Chassis Power Card and Support Cables

Power Card

Part Number Part Type Where Used

CSE-PTJBOD-CB2 Power CardAllows the chassis to be used as a JBOD (Just a Bunch of Drives) system.

Chassis Power CardInacascadedconfiguration,thefirstchassisincludesamotherboardandatleastone host bus adapter. Other servers in this enclosed system must be equipped with a power card. This section describes the supported power card for the BPN-SAS2-216EL series backplane.

For more information, see the Supermicro website at http://www.supermicro.com.

+

C38

Q1

BUZZER1

J1

112

1324

F5

F9

F8

F7

F4

F3 F2

F1

C1

C3

U3

U1

+

EC3

+

EC2

+

EC1

D1A C

MH4MH3

MH2MH1

JF1

1

2

19

20

U7

J17

1 5

4

1

FAN8/X

4

1

FAN7/X

4

1

FAN6/X

4

1

FAN5/X

4 1FAN1

4 1

FAN24 1

FAN34 1

FAN4

I2C

3 2 1

U2

U4

U8

J13

1

BAR CODE

JP7

XHDD PWR NMILEDLED

NIC

1

PWR OH/FF

NIC

2PWRFAIL

RST

ON

REV 1.01CSE-PTJBOD-CB2

Figure 3-7: Chassis Power Card (Sold Separately)

3-5


Figure 3-9: Dual Internal Host Bus Adapter

Supported Internal HBA CablesUse the following cables to create connections between the internal HBA and SAS2-216EL model backplane. The cables required depend upon the HBA connector.

Cable Name: iPass to 4-LanePart #: CBL-0117LLength: 46 cm (18 inches)Description: This cable has one SFF-8484 (32-pin) connector at one end and one iPass (SFF-8087/Mini-SAS) connector (36-pin) at the other. This cable connects from the HBA to the SAS2-216EL backplane

Connecting an Internal HBA to the Backplane The following section lists the most common cables used to connect the HBA to the backplane.

Figure 3-8: Single Internal Host Bus Adapter

HBA HBA

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+EC6 +

C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


HBA

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


IMPORTANT: See Section 3-3 of this manual, Failover with RAID Cards and Multiple HBAsforimportantinformationonsupportedconfigurations.

3-6


Cable Name: iPass (Mini-SAS) to iPass (Mini-SAS)

Part #: CBL-0108L-02 Length: 39 cm (15 inches)



Description: This cable has an iPass (SFF-8087/Mini-SAS) connector (36-pin) at each end. It connects from the HBA to the BPN-SAS2-216EL model backplane.

3-7


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


Connecting an External HBA to the Backplane Thisbackplanesupportsexternalhostbusadapters.Inthisconfiguration,theHBAand the backplane are in different physical chassis. This allows a JBOD (Just a BunchOfDrives)configurationfromanexistingsystem.

HBA Power Card

HBA

Dual External Host Bus Adapter

CBL-0166L External HBA Cables

HBA Power Card

CBL-0166L External HBA Cable

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


Figure 3-10: Single External Host Adapter

Figure 3-11: Dual External Host Bus Adapter

Single External Host Bus Adapter


3-8


Supported External HBA to Backplane CableUsethefollowingcableifyourexternalHBAhasanInfiniBandconnector.

Figure3-12:SASInfiniBandCable(CBL-0200L)

Cable Name:SASInfiniBandtoMini-SASX41Mcable,PBFPart #: CBL-0200LLength: One meterDescription:ThiscablehasanInfiniBandconnector(SFF-8470)ononeendandanSFF-8088-1X (26-pin) connector at the other end.

3-9


CBL-0167L with Single Port Assembly

(Internal cable)

CBL-0166L (External cable)

HBA

Port B Expander 2

Power Card

Port B Expander 2 Port A Expander 1

Connecting Multiple Backplanes in a Single Channel Environment

This section describes the cables used when cascading from a single HBA. These connections use CBL-0167L internal cables and CBL-0166L external cables.

Figure3-13:SingleHBAConfiguration

Port A Expander 1

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


3-10


Cable Name: SAS EL2/EL1 Cascading Cable (External), 68 cm

Part #: CBL-0166L (SFF-8088 1x to SFF-8088 x1)Ports: Single or DualPlacement: External cableDescription: External cascading cable. Connects ports between servers. With most connectors, use one cable for single port connections and two cables for dual port connections.

Cable Name: SAS EL2/EL1 Backplane Cable (Internal) with 2-port Cascading Cable, 68 cm

Part #: CBL-0167L (SFF-8087 to SFF-8088 x1)Ports: SinglePlacement: Internal cableDescription: Internal cable. Connects the backplane to the HBA or external port. Used in single port environments

SingleHBAConfigurationCables

Single Port Cable Assembly

Figure 3-14: Single Port Internal Cable (CBL-0167L)

Figure 3-15: External Cable (CBL-0166L)

3-11


Cable 0166L (External cable)

Port A Expander 1

HBA HBA

Power Card

Port A Expander 1Port B Expander 2

Cable 0168L with Single Port Assembly

(Internal cable)

Connecting Multiple Backplanes in a Dual Channel Environment

This section describes the cables used when cascading from dual HBAs. These connections use CBL-0168L internal cables and CBL-0166L external cables.

Figure3-16:DualHBAConfiguration

Port B Expander 2


3-12


Cable Name: SAS Dual-port Cable Assembly, 68/76 cm

Part #: CBL-0168LPlacement: Internal cablePorts: DualDescription: Internal cascading cable. Connects the backplane to the host bus adapter or external port. Used in dual port environments.

Cable Name: SAS EL2/EL1 Cascading Cable (External), 68 cm

Part #: CBL-0166LPlacement: External CablePorts: Single or DualDescription: External cascading cable. Connects ports between servers. Use one cable for single port connections and two cables for dual port connections.

DualHBAConfigurationCables

Dual Port Cable Assembly

Figure 3-18: External Cable (CBL-0166L)

Figure 3-17: Dual Port Internal Cable (CBL-0168L)

3-13


Cascading allows the system to access data at a faster rate by allowing several backplanes to share resources to reduce latency time.

The first backplane in a cascaded system requires amotherboard and anHBA.Other servers require a power control card with no motherboard and no HBA. For moreinformation,specificchassismanualsareavailableatwww.supermicro.com.

3-5 SupportedCascadingConfigurations

Cable 0167L (Internal cable)



HBA


Power Card


Power Card


Figure3-19:SimpleCascadedConfiguration

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWNBA

R COD

E

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


3-14


Server System with Single SAS HBATheexpandersallowhorizontalbranching.Thisconfigurationalsoappliestodualports.



HBA

Power Card

Port A Expander 1

Power Card

Port A Expander 1

Power Card

Port A Expander 1

Power Card Power Card

Port A Expander 1


Cable 0168L Cable 0167L

Cable 0167L

Cable 0167L

Cable 0167L

Cable 0167L

Port A Expander 1

Figure3-20:CascadedConfigurationwithHorizontalBranching

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


Port A Expander 1

Cable 0168L

Cable 0168L

3-15


Cable 0166L (External cables)

Port A Expander 1

HBA

Power Card

Port A Expander 1

Power Card


Dual Port Cable Assembly

Figure3-21:DualSASHBAwithCascadedConfiguration

DualSASHBAandCascadedConfiguration

HBA

Port B Expander 2

Port B Expander 2

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


Port A Expander 1

Port B Expander 2


3-16



HBAHBA

Power Card

Port B Ex. 2 Port A Ex. 1

Power Card


Power Card


Port A Ex. 1

Power Card


Power Card

Port B Ex. 2

FigureC-27:DualSASHBACascadedConfigurationandBranching

DualSASHBAandCascadedConfigurationwithBranching

MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA


MH4 MH3

MH2

MH1

R159

R157R158R161

BCA534

BCA236BCA2341

MDIOINTERFACE

U320

ACT0

AC

L37

18

U16

U3261617

3233 48

49

64

L396

14 SM

ART_U

ART

14

EXPDBG1Y9

Q3

PRI_MO

DE2

13

PRI_MO

DE1

13

Q1

PRI_J3

PRI_J2

PRI_J1

P_ICE_RTCK

P_ICE_TCK

P_ICE_TDO

2

1

J2

+

EC6 +C2926

++EC5

+EC2

+

EC1

+

EC3

+C862

+

C861

+ C860

+

+C858

+ 5

Y

E

20

R

K

10 15

AE

25 28

AH

WWN

BAR CO

DE

1.02REV:


30ANGLE


XXXXXX

.010

.03

.1

TOLERANCESDECIMAL

ARE IN INCHES


DATE: 12/03/2009



TEL:408-503-8000 FAX:408-503-8008



A

A

DESIGNED IN USA

Rev:1.02BPN-SAS2-216ELPort A Ex. 1

Port B Ex. 2

IMPORTANT: See Section C-12 of this manual, Failover with RAID Cards and Multiple HBAsforimportantinformationonsupportedconfigurations.

Cable 0168L

Cable 0168L

Cable 0168L

3-17


Notes

3-18


Disclaimer (cont.)The products sold by Supermicro are not intended for and will not be used in life sup-port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to per-formbereasonablyexpectedtoresultinsignificantinjuryorlossoflifeorcatastrophicproperty damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

bpn-sas2-216el1/el2 backplane · taiwan (r.o.c) tel: +886-(2) 8226-3990 fax: +886-(2) 8226-3992...

Documents