booster & spacer hardware

Revised:15/10/28

DynaEnergetics™ distributes the following booster and spacer hardware for Hollow Carrier Gun Systems.

Booster & Spacer Hardware

Revised: 11/12/16

Part No. Type Temperature Rating 2315723 Slimline Booster Kit DYNAWELL 230oC / 450oF

Booster Kit DYNAWELL Slimline

Application The DynaEnergetics booster transfer system provides an innovative method for ensuring the reliable detonation of perforating guns run in tandem. It includes a unique upper booster retainer that has a spring which pushes the booster as close as possible to the lower booster retainer. This ensures a reliable transfer by closely aligning the bi-directional boosters end to end and by reducing the likelihood of debris falling between the boosters during operation. This booster Kit is used with Expandable Retrievable Hollow Carrier Guns from 40mm (1-1/16”) to 51mm (2”). Features

• End to End booster transfer

• Spring loaded for optimum positioning

• Designed to prevent detonating cord and booster slippage

Available Sizes One size available for 40mm (1-1/16”) to 51mm (2”) gun systems.

Selection Chart

1 Booster Kit Bottom Part 2 Booster Kit Top Part 3 O-ring 4 Spring

Revised: 11/12/16

Part No. Type Temperature Rating 2316998 Booster Kit DYNAWELL with electric contact 230oC / 450oF 2320708 Booster Kit DW Disassembly Tool N/A

Booster Kit DYNAWELL With Electric Contact

Application The DynaEnergetics booster transfer system provides an innovative method for ensuring the reliable detonation of perforating guns run in tandem. It includes a unique upper booster retainer that has a spring which pushes the booster as close as possible to the lower booster retainer. This ensures a reliable transfer by closely aligning the bi-directional boosters end to end and by reducing the likelihood of debris falling between the boosters during operation. At the same time this Booster Kit allows for electrical contact between guns. This booster Kit is used with Expandable Retrievable Hollow Carrier Guns from 63.5mm (2-1/2”) and bigger Features

• Ballistic and Electric transfer




Available Sizes One size available for 63.5mm / 2-1/2” to 178mm / 7” gun systems. Selection Chart

1 Booster Kit Top Part 2 Booster Kit Top Part w. electric contact 3 O-ring 4 Contact ring 5 Booster Kit Bottom Part 6 Booster Kit Bottom Part w. electric contact 7 Spring

Revised: 11/12/16

Spacer Gun Kit DYNAWELL

Description Designed to allow an explosive transfer in an unloaded gun carrier DYNAWELL. Available Sizes See Below Recommendations Install as per instruction manual. Give 2% excess of length of detonating cord into the assembly to compensate for possible shrinkage in length due to temperature exposure. Selection Chart

Part No. Size (mm / ")

Weight (kg)

Dimension (mm)

2315366 70 / 2.75 0.5 80 x 70 2315367 73 / 2.875 0.6 80 x 73 2315369 86 / 3.375 0.7 80 x 86 2315370 102 / 4 0.9 80 x 102 2315371 114 / 4.5 1.0 80 x 114

- 178 / 7 - - Other sizes available on request

1. Booster Kit DYNAWELL 2. Spacer Plate 3. Retention Ring

Revised: 11/12/16

Part No. Type Temperature Rating 2315319 Booster Kit DYNAWELL 230oC / 450oF 2320708 Booster Kit DW Disassembly Tool N/A

Booster Kit DYNAWELL

Application The DynaEnergetics booster transfer system provides an innovative method for ensuring the reliable detonation of perforating guns run in tandem. It includes an unique upper booster retainer that has a spring which pushes the booster as close as possible to the lower booster retainer. This ensures a reliable transfer by closely aligning the bi-directional boosters end to end and by reducing the likelihood of debris falling between the boosters during operation. This booster Kit is used with Expandable Retrievable Hollow Carrier Guns from 63.5mm (2-1/2”) and bigger Features




Available Sizes One size available for 63.5mm / 2-1/2” to 178mm / 7” gun systems. Selection Chart

1 Booster Kit Bottom Part 2 Booster Kit Top Part 3 O-ring 4 Spring

Revised: 11/12/16

TCP Gun / Safety Spacer System

Description

The DynaEnergetics TCP Gun Spacer System allows the user to perforate multiple intervals simultaneously without the use of prohibitively expensive spacer guns. The system provides a quick and simple method for supporting standard bi-directional boosters and detonating cord in standard EU tubing joints and collars. This system is especially beneficial where the zones to be perforated are separated by long distances. The system can also be used as a safety spacer as per RP67 to place perforating guns below well-head equipment or occupied areas of a rig before the firing head is installed. Features

• No crossover subs are required between tubing joints. Detonating cord is run through the joint and the booster retainers are simply pushed by hand into the ends of the tubing before they are made-up.

• The booster retainers are spring loaded to ensure reliable booster function.

• The system is easily installed in the field using special booster kit installation tool.

• Adapter subs are installed at the top and bottom of the tubing string to allow connection of perforating guns with the industry standard 2-3/4” G.O. top sub thread.

• Can be used in vertical and horizontal applications. Recommendations

• Install as per instruction manual using new tubing to ensure good seal. • Give 2% excess of length of detonating cord into the assembly to compensate for

possible shrinkage in length due to temperature exposure. Specifications

Available for 2 3/8” Tubing 2 7/8” Tubing Part number TBC TBC Tubing OD 60 mm / 2.375” 73 mm / 2.875” Tubing ID 51 mm / 1.995” 62 mm / 2.441” Temperature Rating 230oC / 450 oF Collapse Pressure Rating (Adapter Sub)

20,000 PSI / 137.9 MPa

Revised:15/10/28

DynaEnergetics™ supplies the following sealing boots and accessories for Exposed Gun Systems.

Exposed Gun Subs & Accessories

Revised: 11/12/16

Booster Kit DYNAWELL Slim

Description A booster kit is designed to efficiently transfer the detonation between multiple gun assemblies. Specifications The Booster Kit DYNAWELL Slim is designed to have a minimum air gap between boosters ensuring a functional explosives transfer between Gun Systems. Available Sizes Kit to be used for all through tubing hollow carrier perforating systems DYNAWELL from 40mm to 51mm Selection Chart

Part No. Type Temperature Rating

Weight (kg)

Dimension (mm)

2315723 Booster Kit DYNAWELL Slim 230oC / 450oF 0.1 10 x10 x10

1 Booster Kit DW Slim Bottom Part

2 Booster Kit DW Slim Top Part

3 O-ring

4 Spring

Revised: 11/12/16

Application Designed to hold TTG strip charges. Engineered to retrieve TTG strip charge front caps after charge initiation. Specifications

Top Connector Thread Designed to adapt to firing head for strip DYNAWELL style

Bottom Connection Designed to adapt to tandem strip adapter DYNAWELL style

Available Sizes One size available only for 1 11/16" and 2 1/8" TTG Strip Gun Systems. See chart for lengths and shot densities available. Recommendations Check for damage before each run.

Shot density

Shot distance

Shot interval

Total length

Total shot

13 spm 77 mm 1 m 1.16 m 14 13 spm 77 mm 2 m 2.16 m 27 13 spm 77 mm 3 m 3.16 m 40 20 spm 50 mm 1 m 1.16 m 21 20 spm 50 mm 2 m 2.16 m 41 20 spm 50 mm 3 m 3.16 m 61

Selection Chart

Item Part No. Weight Dimensions 1m Carrier Strip for 13 SPM 2315269 - - 2m Carrier Strip for 13 SPM 2315271 - - 3m Carrier Strip for 13 SPM 2315273 2.3 kg 3.2 x 0.04 x 0.01 m 1m Carrier Strip for 20 SPM 2315270 - - 2m Carrier Strip for 20 SPM 2315272 - - 3m Carrier Strip for 20 SPM 2315274 - -

Carrier Strip for TTG Strip System DYNAWELL

Revised: 11/12/16

Application Designed to connect the strip to the electric connection and to house the detonator. Specifications

Top Connector Thread 1 3/16" - 12 THD. Type "A" Box Bottom Connection Strip DYNAWELL

Available Sizes One size available only for 1 11/16" and 2 1/8" TTG Strip System. Recommendations Check for damage before each run. Selection Chart

Item Part No. Weight Dimensions

Adapter Head TTG Strip 2819076 1.70 kg 42.8 mm OD x 270mm length

Adapter Head TTG Strip

Revised: 11/12/16

Application Designed to connect two strips type DYNAWELL and to connect the strip to the bottom nose for strip type DYNAWELL. Available Sizes One size available only for 1 11/16" and 2 1/8" TTG Strip System. Recommendations Check for damage before each run. Selection Chart

Item Part No. Weight Dimensions Tandem Strip Adapter 2819142 - -

Tandem Strip Adapter

Revised: 11/12/16

Application Designed to decentralize the TTG strip system DYNAWELL. Available Sizes One size available only for 1 11/16" and 2 1/8" TTG Strip System. Recommendations Check for damage before each run. Recommended to always be run in conjunction with upper magnetic decentralizer. Selection Chart

Item Part No. Weight Dimensions Bottom Nose for Strip 2819092 - -

Bottom Nose for Strip

Revised: 11/12/16

Application Designed to guide Strip and Link TTG systems when running into the well bore on electric wireline and slickline. Available Sizes Sizes available for 1 11/16" and 2 1/8" TTG Strip and Link Systems. Extended length for TTG Link bottom nose to accommodate for a variety of detonator options. Recommendations

• Follow DynaEnergetics assembly instruction.

• Recommended to always be run in conjunction with upper magnetic decentralizer.

• Check for damage before each run.

Selection Chart

Item Part No. Size (mm / ") Bottom Nose for Strip Model 2 with Spring 2819092 43mm and 54mm / 1 11/16” and 2 1/8” Bottom Nose for Strip Model 2, Variation1 4904492 43mm and 54mm / 1 11/16” and 2 1/8” Bottom Nose for Strip Model 2, Variation 2 4904499 43mm / 1 11/16” Bottom Nose for Strip Model 2, Variation 3 4904500 54mm /2 1/8”

Bottom Nose for Link System 2819175 43mm and 54mm / 1 11/16” and 2 1/8”

DynaEnergetics Bottom Nose for Strip/Link TTG

Note: Product condition must be monitored, inspected and maintained regularly to ensure proper service in accordance with DynaEnergetics guideline. Failure to do so may result in personal injury and/ or property damage. For questions

please contact your DynaEnergetics representative.

Model 2 Variation 1 Model 2 with Spring

Model 2 Variation 2 & 3 Link System Bottom Nose

Revised: 11/12/16

Application Includes all expendable components for assembly of TTG Strip System DYNAWELL

• Detonating Cord Holder / Detonator Holder • Screws (to attach strip to firing head and tandem adaptor) • Sealing Boot for Detonator • Sealing Boot for Detonating Cord End • Sealing for Electric Connection

Available Sizes See table below. Recommendations In order to ensure proper seal, it is recommended to string the tie boot ends with seizing cord. Selection Chart

Item Part No. Weight Dimensions Hardware Kit for Strip for Detonator Z480 &

1018 2819449 - -

Hardware Kit for Strip for Detonator 1015E &

1423 2311155 - -

Hardware Kits for TTG Strip Systems

Accessory Kit Strip consists of items 3 to 7

3. Detonating Cord Holder (2ea.) /

Detonator Holder (1ea.) 4. Screw (12ea.) 5. Sealing Boot for Detonator (1ea.) 6. Sealing Boot for Detonating Cord End

(1ea.) 7. Sealing Boot for Electrical Wire

Connection (1ea.)

Revised: 11/12/16

Application Designed to connect the link charge holders to the electric connection. Specifications

Top Connector Thread 1 3/16" - 12 THD. Type "A" Box Bottom Connection Link Type DYNAWELL

Available Sizes One size available only for 1 11/16" and 2 1/8" TTG Link System. Recommendations Check for damage before each run. Selection Chart

Item Part No. Weight Dimensions

Adapter Head TTG Link 2314293 1.70 kg 42.8 mm OD x 270 mm length

Adapter Head TTG Link

Revised: 11/12/16

Application Includes all expendable components for assembly of TTG Link System DYNAWELL

• Sealing Boot for Detonating Cord End • Sealing Boot for Detonator • Sealing for Electric Connection • Sealing Boot for Electric Wire Connection • Detonating Cord Holder • Bottom Nose for Link

Available Sizes See table below. Recommendations In order to ensure proper seal, it is recommended to string the tie boot ends with seizing cord. Selection Chart

Item Part No. Weight Dimensions Hardware Kit for Link for Detonator Z480 & 1018 2311156 - -

Hardware Kit for Link for Detonator 1015E & 1423 2311157 - -

Hardware Kits for TTG Link Systems

Accessory Kit Link consists of items 2 to 5, 7 & 10

2. Sealing Boot for Detonating Cord End 3. Sealing Boot for Detonator 4. Sealing Boot for Electric Wire

Connection 5. Sealing Sleeve for Electric Wire

Connection 7. Detonating Cord Holder 10. Bottom Nose for Link

Revised:15/10/29

The innovative DynaSlot™ system is designed specifically for plug and abandonment cement squeeze operations. Well abandonment (P&A) involves complicated procedures where the wellbore must be shut in and permanently sealed. It is essential that the layers of sedimentary rock, in particular freshwater aquifers, are pressure isolated. Unwanted vertical channels or voids in a previously cemented wellbore annulus may exist. These channels can produce migration pathways for fluids or gas, resulting in:

• Channels in the cemented annulus • Migration of fluids or gas • Leakage risks • Cross flow and Cross-contamination • Environmental issues

This hollow carrier perforating gun system employs a unique scallop design which provides sufficient surface area for the perforation slot without sacrificing burr height protrusion, system performance or mechanical integrity. As an alternative application, the DynaSlot™ may be used to achieve bigger cross sectional flow areas than comparative charges.

Gun System DynaSlot

Revised: 15/05/26

Configuration Schematic Shot Pattern

Technical Information

Carrier Specifications

Gun Type Expendable, Scalloped

Pressure Rating 172 MPa / 25,000 psi

Temperature Rating Depending on Explosives

Tensile Strength 200,000 daN / 450,000 lbs

Tandem Shot Spacing 0.40 m / 1.31 ft

Carrier Thread 2.812" - 6 TPI Acme

Selection Chart

Revised:15/10/29

DynaEnergetics™ manufactures and sells the following subs for Hollow Carrier and TCP Systems.

Subs for Hollow Carrier & TCP

Revised: 11/12/16

Top Fire Sub, Type II

Description

The DynaEnergetics Top Fire Sub Provides users with a safe, convenient, and reliable means of detonating a perforating or stimulation tool from the top of the assembly. This tool is useful any time it is undesirable or impossible to run shooting wire through the entire perforating assembly. Features

• The internal chamber is covered by a sliding sleeve. This provides the largest opening possible.

• The sleeve seal has a unique directional function. This allows gas pressure to vent as the perforating assembly is detonated, extending the life of the assembly.

• The top and bottom threads are compatible with all common CCL’s and top subs in the industry.

• The length is tailored to provide a standard CCL to top shot distance.

Specifications

Nominal Size 79 mm to 127mm / 3 1/8” to 5” Part number 2319444 / 2317679 Overall Length 254 mm / 10.00" Maximum OD 86 mm / 3.375” Minimum ID 8 mm / 0.3158” Temperature Rating

Varies with elastomer; 204oC with standard viton seal.

Pressure Rating 10,000 PSI / 68.9 MPa Tensile 66,500 kg / 146,610 # Connections 2.75" 6 "GO" Acme Pin up, Box down Material 4140 HTSR

www.dynaenergetics.com [email protected]

DESCRIPTIONTop sub for expendable hollow retrieveable perforating systems.

SPECIFICATIONS Pressure Rating 172 MPa / 25,000 psi

Temperature Rating Depending on O-Ring type as specif ied below

Top Thread Type 2-3/4” - 6 TPI ACME

O-Ring Top Connection 2819498

TCP Top Sub DYNAWELLRevised 22.JUNE.2018

PACKING INFORMATION Sub O.D. Product Weight Dimensions of Product

63.5mm* 2 1/2”* 5.03 kg 200 mm x 86 mm

70mm 2 3/4” 4.80 kg 220 mm x 70 mm

73mm 2 7/8” 5.50 kg 200 mm x 73 mm

79mm 3 1/8“ On Request On Request

86mm 3 3/8” 6.20 kg 190 mm x 86 mm

102mm 4” 8.76 kg 200 mm x 102 mm

114mm 4 1/2” 11.62 kg 211 mm x 114 mm

127mm 5” 13.20 kg 210 mm x 127 mm

178mm 7” 26.85 kg 220 mm x 178 mm

+/-5 % tolerance in weights

SELECTION CHARTSub O.D. Bottom Thread Type (“) Part No. Part No. O-Ring Temperature Rating

(mm) (“) O-Ring63.5mm* 2 1/2”* 2.1875” (6 TPI Acme) 2329282 On Request 260 oC / 500 oF

70mm 2 3/4” 2.375” (6 TPI Acme) 2329283 2313370 260 oC / 500 oF

73mm 2 7/8” 2.375” (6 TPI Acme) 2329284 2313370 260 oC / 500 oF

79mm 3 1/8“ 2.75” (6 TPI Acme) 2329285 On Request 260 oC / 500 oF

86mm 3 3/8” 2.8125” (6 TPI Acme) 2329286 2819415 260 oC / 500 oF

102mm 4” 3.4375” (6 TPI Acme) 2329287 2313376 260 oC / 500 oF

114mm 4 1/2” 3.9375” (6 TPI Acme) 2329052 2313375 260 oC / 500 oF

127mm 5” 4.500” (6 TPI Acme) 2329279 On Request 260 oC / 500 oF

178mm 7” 6.25” (6 TPI Acme) 2329281 2315754 260 oC / 500 oF

*Sub OD is 86mm (3-3/8”), gun size is 63.5mm (2-1/2”)

Note: Product condit ion must be monitored, inspected and maintained regularly to ensure proper service in accordance with DynaEnerget ics guidel ine. Fai lure to do so may result in personal injury and/ or property damage. For quest ions please contact your DynaEnerget ics representat ive.

Revised: 11/12/16

Top Sub DYNAWELL Wireline

Description Top sub for wireline use in expendable hollow retrievable perforating systems. Specifications

Pressure Rating 172 MPa / 25,000 psi Temperature Rating Depending on O-Ring type as specified

below Top Thread Type 1-3/16” – 12THD Type “A” Box

Packing Information

Sub O.D. Product Weight Dimensions of Product 40mm 1 9/16” 0.65 kg 185 mm x 40 mm 51mm 2" 2.07 kg 185 mm x 51 mm

63.5mm 2 ½” 4.00 kg 215 mm x 63.5 mm 70mm 2 ¾” 4.85 kg 215 mm x 70 mm 73mm 2 7/8" 5.14 kg 215 mm x 73 mm 79mm 3 1/8“ On Request On Request

+/- 5 % tolerance in weights

Selection Chart

Sub O.D (mm) (")

Bottom Thread Type (") Part No. Top Sub

Part No. O-Ring Temperature Rating O-Ring

40mm 1 19/16” 1.275” (12 TPI Acme) 2315880 2316332 260oC / 500oF 51mm 2” 1.687” (8 TPI Stub Acme) 2315875 2315727 260oC / 500oF

63.5mm 2 ½” 2.1875” (6 TPI Acme) 2325870 On Request 260oC / 500oF 70mm 2 ¾” 2.375” (6 TPI Acme) 2315227 2313370 260oC / 500oF 73mm 2 7/8” 2.375” (6 TPI Acme) 2315230 2313370 260oC / 500oF 79mm 3 1/8“ 2.75” (6 TPI Acme) On Request On Request 260oC / 500oF

Note: Product condition must be monitored, inspected and maintained regularly to ensure proper service in

accordance with DynaEnergetics guideline. Failure to do so may result in personal injury and/ or property damage. For questions please contact your DynaEnergetics representative.

Revised: 11/12/16

Top Sub DYNAWELL CIS Design

Description Top sub for expendable hollow retrievable perforating systems. Specifications


below Top Thread Type 2-3/4” – 6 TPI ACME

O-Ring Top Connection 2819498

Packing Information

Sub O.D. Product Weight Dimensions of Product 86mm 3 3/8" 5.76 kg 190 mm x 86 mm 89mm 3 ½” 6.37 kg 190 mm x 89 mm

102mm 4" 5.76 kg 200 mm x 102 mm 114mm 4 ½” 11.11 kg 211 mm x 114 mm 127mm 5” 13.6kg 210 mm x 127 mm


Selection Chart

Sub O.D (mm) (")

Bottom Thread Type (")

Part No. Tandem Sub CIS Design


86mm 3 3/8” 2.8125” (6 TPI Acme) 2315236 2819415 260oC / 500oF 89mm 3 ½” 3” (6 TPI Acme) 2323600 2317015 260oC / 500oF

102mm 4” 3.4375” (6 TPI Acme) 2315239 2313376 260oC / 500oF 114mm 4 ½” 3.9375” (6 TPI Acme) 2315242 2313375 260oC / 500oF 127mm 5” 4.5” (6 TPI Acme) 2325583 On Request 260oC / 500oF

Note: Product condition must be monitored, inspected and maintained regularly to ensure proper service in accordance

with DynaEnergetics guideline. Failure to do so may result in personal injury and/ or property damage. For questions please contact your DynaEnergetics representative.

Revised: 11/12/16

Tandem Select Fire Subs

Description

The DynaEnergetics Tandem Select Fire Sub is used when two or more guns on the same string are to be detonated at different times. The assembly is designed to accept industry standard pressure switches. Features

• Suitable for P-100 (positive), N-100 (negative), or EBDD (diode) types of EBS switches.

• Large internal cavity for terminating wires. • Robust Acme thread on the port cover maximizes tool

life. • Face seal on port cover ensures a reliable seal. • Cover is compatible with DynaEnergetics Safety

Spanner Wrench, and Baker Style Bleed Off Wrench

Specifications

Nominal Size 86 mm 101 mm Part number 2319401 2319424 Overall Length 270 mm / 10.64" 293 mm / 11.54" Maximum OD 88 mm / 3.375” 101 mm / 4.00” Minimum ID 14 mm / 0.563” 14 mm / 0.563” Temperature Rating

Varies with elastomer; 204oC with standard viton seal

Pressure Rating 10,000 PSI / 68.95 MPa Tensile 223,000# / 101,15 kg 348,000# / 157,85 kg Connections 2 13/16" box up, pin down 3 17/16" 6 Acme Pin x Pin Material 4140 HTSR

Revised: 11/12/16

Tandem Isolation Sub

Description

The DynaEnergetics Tandem Isolation Sub allows the operator to safely and efficiently make up and arm strings of guns that are to be selectively fired.

The operator can pre-assemble individual guns with select fire switches pre-wired and ready to make up. No wiring between guns is required. When the gun string is made up, a sprung loaded contact automatically establishes a connection with the communication line that runs through the entire gun string.

Once the string is assembled, the large ports in the Tandem Isolation Subs are opened and the detonators can be installed electrically before ballistically.

The Tandem Isolation Sub was designed to accommodate DynaEnergetics RF safe detonators and select fire system.

Features

• Short overall length. • Large internal cavity for terminating wires and ease of assembly. • Spring loaded through-wire contact. • Positive ground connection to sub body. • The top and bottom sub-assemblies can be changed to

accommodate larger gun diameters. • A special “Plug-Shoot” Bottom sub-assembly can be used to allow

the connection of a standard setting tool. • High pressure versions are available on request.

Specifications

Nominal Gun Size 73mm / 2 7/8” 79 mm / 3 1/8” 86mm / 3 3/8” 102 mm / 4” Part number 2319374 2320654 2319404 2319426 Overall Length 582mm / 22.9” 582 mm / 22.9" 546mm / 21.5” 582 mm / 22.9" Maximum OD 73 mm / 2.875” 85.7 mm / 3.375” 85.7 mm / 3.375” 101 mm / 4.00” Length Over Gun shoulder

419mm / 16.5” 436mm / 17.5” 404mm / 15.9” 417mm / 16.4”

Temperature Rating Varies with elastomer; 204oC with standard Viton seal Pressure Rating 172.4Mpa / 25 000PSI 110.3Mpa / 16 000PSI 137.9Mpa / 20 000PSI for High Pressure Version Tensile 27810kg / 61300# 38688kg / 94770# Connections Standard Gun Thread Pin Material 4140 HTSR Contact Assembly Kit 2319445 Re-Dress Kit 2319375 2319409

Revised: 11/12/16

Tandem Sub DYNAWELL

Description Tandem sub for expendable hollow retrievable perforating systems. Specifications


below

Packing Information


63.5mm 2 ½” 3.95 kg 235 mm x 63.5 mm 70mm 2 ¾” 10.89 kg 235 mm x 70 mm 73mm 2 7/8" 11.00 kg 235 mm x 73 mm 79mm 3 1/8“ On Request On Request 86mm 3 3/8" 6.50 kg 210 mm x 86 mm

102mm 4" 10.54 kg 230 mm x 102 mm 114mm 4 ½” 13.79kg 230 mm x 114 mm 127mm 5” 16.20kg 230 mm x 127 mm 178mm 7" 34.5kg 230 mm x 178 mm


Selection Chart

Sub O.D (mm) (")

Thread Type (") Part No. Tandem Sub



63.5mm 2 ½” 2.1875” (6 TPI Acme) 2325871 On Request 260oC / 500oF 70mm 2 ¾” 2.375” (6 TPI Acme) 2315243 2313370 260oC / 500oF 73mm 2 7/8” 2.375” (6 TPI Acme) 2315245 2313370 260oC / 500oF 79mm 3 1/8“ 2.75” (6 TPI Acme) On Request On Request 260oC / 500oF 86mm 3 3/8” 2.8125” (6 TPI Acme) 2315247 2819415 260oC / 500oF

102mm 4” 3.4375” (6 TPI Acme) 2315249 2313376 260oC / 500oF 114mm 4 ½” 3.9375” (6 TPI Acme) 2315251 2313375 260oC / 500oF 127mm 5” 4.500” (6 TPI Acme) On Request On Request 260oC / 500oF 178mm 7” 6.25” (6 TPI Acme) 2315759 2315754 260oC / 500oF



Revised: 11/12/16

Tandem Sub DYNAWELL CIS Design

Description Tandem sub for expendable hollow retrievable perforating systems. Specifications


below

Packing Information




Selection Chart

Sub O.D (mm) (")

Thread Type (") Part No. Tandem Sub CIS Design






Revised: 11/12/16

Bottom Sub DYNAWELL

Description Bottom sub for expendable hollow retrievable perforating systems. Specifications


below

Packing Information


63.5mm 2 ½” 2.3 kg 140 mm x 63.5 mm 70mm 2 ¾” 2.8 kg 140 mm x 70 mm 73mm 2 7/8" 3.0 kg 140 mm x 73 mm 79mm 3 1/8“ On Request On Request 86mm 3 3/8" 4.6 kg 165 mm x 86 mm 89mm 3 ½” 5.9 kg 165 mm x 89 mm

102mm 4" 9.3 kg 200 mm x 102 mm 114mm 4 ½” 11.0 kg 190 mm x 114 mm 127mm 5” 13.5kg 190 mm x 127 mm 178mm 7" 17.5kg 150 mm x 178 mm


Selection Chart

Sub O.D (mm) (")

Thread Type (") Part No. Bottom Sub



63.5mm 2 ½” 2.1875” (6 TPI Acme) 2325872 On Request 260oC / 500oF 70mm 2 ¾” 2.375” (6 TPI Acme) 2315253 2313370 260oC / 500oF 73mm 2 7/8” 2.375” (6 TPI Acme) 2315255 2313370 260oC / 500oF 79mm 3 1/8“ 2.75” (6 TPI Acme) 2319392 On Request 260oC / 500oF 86mm 3 3/8” 2.8125” (6 TPI Acme) 2315257 2819415 260oC / 500oF

102mm 4” 3.4375” (6 TPI Acme) 2315259 2313376 260oC / 500oF 114mm 4 ½” 3.9375” (6 TPI Acme) 2315261 2313375 260oC / 500oF 127mm 5” 4.500” (6 TPI Acme) On Request On Request 260oC / 500oF 178mm 7” 6.25” (6 TPI Acme) 2315758 2315754 260oC / 500oF



Revised: 11/12/16

Bottom Sub DYNAWELL CIS Design

Description Bottom sub for expendable hollow retrievable perforating systems. Specifications


below

Packing Information




Selection Chart

Sub O.D (mm) (")

Thread Type (") Part No. Bottom Sub CIS Design






Revised:15/10/29

Wireline Subs

Revised: 13/02/26

Application Designed as firing head and mechanical connection between correlation device and loaded DynaEnergetics perforating gun system using the DynaEnergetics TopFire family of detonators GO type connection. Available Sizes The 2” firing head assembly including blast absorber, firing head adapter and high pressure firing sub (1-1/2” GO Type) can be used with the following DynaEnergetics perforating gun system (see chart below).

Sub O.D (mm) (")

Thread Type Bottom (")

Part No. Top Sub

Part No. O-Ring

Temperature Rating O-Ring

51mm 2” 1.6875” (8 TPI Acme) 2315879 2315727 260oC / 500oF Recommendations

• Check insulation and continuity before each run.

• Use bidirectional booster in the gun top sub

• Always arm detonator and gun system electrically before ballistically

Specifications

Complete Kit Quick Change Assembly Part number 2326141 O-rings 013 VITON 90 DUR* 117 VITON 90 DUR* 214 VITON 90 DUR* 221 VITON 90 DUR Maximum OD 51.6 mm / 2.03” Temperature Rating

Varies with elastomer selection

Pressure Rating 21,000 PSI / 144 MPa Connections 1.6875" 8 Acme Box down 1 3/16” 12 UN-2B Box up

Replacement Items

Re-dress Kit Firing Head Adapter 1-1/2” Go HP Firing Sub

Part number 2326142 2326132 2325757 *included in Re-dress Kit Note: Product condition must be monitored, inspected and maintained regularly to ensure proper service in accordance with

DynaEnergetics guideline. Failure to do so may result in personal injury and/ or property damage. For questions please contact your DynaEnergetics representative.

2” Firing Head Assembly for Top Fire Detonator

booster & spacer hardware

Documents