Superfast Boom Barrier

User Manual

Installing The Boom Barrier

PCB Number GCBV420 Software version V310

BOM Number GCB201212061223 Application Could be upgraded

Introduction

This product installs in electric barrier gate to control barrier rod up and down. Control board

includes remote control module. T hrough remote controller, controller board can control barrier

rod up and down. Connect wire to relative terminal and press key to control barrier rod up and

down. And through RS -485 port, data protocol control barrier gate and obtain state.

l Equipped with RS-485 COM terminal. Support PGIS protocol. Can control barrier rod up

and down through computer and obtain state. Maximum COM distance is 1200 meters.

l Equipped with vehicle detector terminal. Can realize car anti -smashing and automatic rod

down when car passing.

l Compatible with general limit sensor with/without power source.

l Automatically matching code to setup remote controller. 7 groups of different codes can

be set. Setting times over 300 millions and service life over 10 years.

l Can connect wire controller to operate barrier gate through dry contact.

l Equipped with motor revolution speed test function (optional function).

Picture of Product

Picture 1: Barrier Gate Printed Circuit Board

Installing The Boom Barrier

Specification

u Input power supply: AC220V±20% / 3A

u Output direct current power supply: 12V/100MA

u Motor standard: 220V Single-Phrase AC Motor

Definition of Wiring Terminal

Terminal Function

J1 revolution speed transducer terminal

J2 anti-smashing terminal (infrared/vehicle detector)

J3 communication terminal

J4 passable sign terminal

J5 rod height sensor terminal

J6 power terminal, connect standard power/motor

J8 wire control terminal

l J2 anti-smashing terminal, including anti -smashing and anti-smashing/rod falling function.

Anti-smashing: When anti-smashing input signal works, rod stops falling and rising to

vertical position. Rod falling command will be in failure.

Anti-smashing/rod falling : Including anti-smashing function, when canceling anti -smashing

signal, rod will fall to horizontal position automatically.

l J4 passable sign terminal, car passing allowed only when rod in vertical position.

l J5 rod height sensor terminal, it releases position signal to stop motor running when rod in is

relative position. Hall components and reed switch can be as sensor. Effective high -low level

sensor is connected to relative terminal.

Definition of J5 Wiring Terminal

² +12V can be as effective high level driver power source and supply power for sensor.

² Passive sensor can connect low active and high active based on output feature. Low

active connects 2, 5 and 6 pin. 6 pin is public. High active connect 1, 3 and 4 pin. 1 pin

is public.

² Active sensor is powered by 1 and 6 pin. According to output active level, low connects

2 and 5 pin and high connects 3 and 4 pin.

l J6 is power terminal, including standard power AC220V power input and motor driver port.

Terminal Definition Attribution Description

1 +12V +12Vvoltage output/<100mA

2 LHOR horizontal low level active

3 HHOR horizon high level active

4 HVER vertical high level active

5 LVER vertical low level active

6 GND GND

Installing The Boom Barrier

Definition of J6 Terminal:

l J8 is wire control terminal, control barrier gate through dry contact.

OPEN：Rod rising to vertical position automatically

CLOSE：Rod falling to horizontal position automatically (anti-smashing signal limit)

STOP：Rod stops in any state

Definition of Function:

² Vertical: effective sensor input signal vertical position

² Horizontal: effective sensor input signal horizontal position

² Passable sign: car passing allowed only when rod in vertical position

² Anti-smashing: When anti -smashing input signal works, rod stops falling and rising to

vertical position. Rod falling command will be in failure.

² Anti-smashing/rod down: Including anti-smashing function, when canceling

anti-smashing signal, rod will fall to horizontal position automatically.

² OPEN：rod rising to vertical position automatically

² CLOSE：rod falling to horizontal position automatically (anti-smashing signal limit)

² STOP：Rod stops in any state

² Change direction: Firstly stop barrier gate working and change rod running direction and

then startup.

Definition of Key

Key Definition Function Description

K1 open rod rising to vertical position

K2 close Rod falling to horizontal position

K3 stop rod stop working

K4 remote control

matching code register or clean remote control code

Terminal Definition Function Description

1 AC220V Live Line standard power input

2 AC220V Null Line standard power input

3 GND protection

4 MOUT public motor winding

5 MOUR+C motor close direction winding and container

6 MOUY+C motor open direction winding and container

Installing The Boom Barrier

Definition of Indicator

Indicator Note Color

HOR rod horizontal sensor output red, lights on in horizontal state

VER Rod vertical sensor output green, lights on in vertical state

RUN motor running red

DIR motor close direction green

LAM external red indicator lights on/overtime

alarm/remote controller setting red

COM communication yellow, receiving signal icker once

PWR power supply green, stay lit with power on

Typical Parameter

u Pulse Width

Tab Note Effective Width

EXA active external vehicle detector signal input active >100ms

EXA release external vehicle detector signal input release >180ms

OPEN/CLOSE active open/close control signal input active ≤200ms ignored

≥220ms executed

STOP active ≤160ms ignored

≥180ms executed

VER active vertical position arrival active >20ms

VER null Vertical position leave active >20ms

HOR active horizontal position arrival active >20ms

HOR null horizontal position leave active >20ms

u Capability Parameter of Input/Output Port

Tab Note Effective Range

AC220V standard power input voltage AC220V±20%/3A

MOTU/Y/R ( I ) motor terminal current <6A/AC220V

STU passable indicator control signal <-20mA/30V(sink current)

OPEN/CLOSE/STOP open/close/stop control signal input (passive

contact/optical coupler) <1mA/DC5V(source current)

EXA External vehicle detector signal input

(passive contact/optical coupler) <1mA/DC5V(source current)

VER/HOR low active vertical/horizontal low active signal input <1mA/DC5V(source current)

VER/HOR high active vertical/horizontal high active signal input <-1mA/DC30V(sink current)

Installing The Boom Barrier

u Absolute Maximum Ratings

Tab Note Attribute

AC220V standard power terminal surge（EN61000-4-5） educed/±2KV

STU passable indicator port surge（EN61000-4-5） educed /±2KV

OPEN/CLOSE/STOP open/close/stop control port rapid pulse

（EN61000-4-4） educed/±2KV

EXA external vehicle detector input port （to GND） educed/-1V-+5V5

VER/HOR low active vertical/horizontal position low active port (to GND) educed/-1V-+5V5

VER/HOR high active vertical/horizontal position high active port (to GND) educed/-30V-+30V

Remote Controller Module

The Barrier Gate PCB is standard congured. User can setup remote controller by matching code.

7 groups of different code can be settled for each control board. Times of resetting are over 3

millions and service life is more than 10 years

u Remote Registration:

Firstly cut off RS-485 COM port, J8 port (wire control port), J2 port (anti-smashing port), and

conrm no car under barrier rod. Then, rise rod to vertical position.

Press K4 key until COM indicator ickers (icker once per 1s). Press any key for 5s（COM

yellow indicator ickers frequently）until LAM red indicator icking once. Finish registration.

Multiple remote controllers can be registered. One remote controller can be registered with 7

different codes. Same codes registered once are all effective. Registration information will be

saved by current record mode over 7 different codes. That means the last code will cover the rst

code in the registered sequence.

u Clean Remote Controller Registration Information:

When barrier rod is in the vertical position (J5 terminal effective, VER green indicator lights on),

press K4 key until COM indicators ickers. And press STOP key until LAM red indicator ickers

once. Clear remote controller successfully. All registered information will be cleaned at once.

Loose K4 key to save operation, it will be effective when power up next time. If not saved, only

cut off power before loose K4 key.

u Attention:

1. Remote controller can work within 80 meters and be failure beyond the distance.

2. If remote controller can not control the relative device in limited distance, rstly check the

battery state to exclude battery running out and then check the code consistency of remote

controller and device.

3. Remote controller can control device if the code of remote controller is same with the receiver

code. If multiple devices are settled with same code, one remote controller will control multiple

devices. Thus, one remote controller can realize not to control multiple devices by setting different

device code.

4. If remote controller can not control barrier gate, please solve faults as follows: ① check remote

controller battery state. If battery runs out, replace battery immediately. ② check remote controller

working in limited distance or not. ③ check remote controller registered correctly or not.