black adjustable computer mobile cart · black adjustable computer mobile cart scan the qr code...
TRANSCRIPT
Black Adjustable Computer Mobile Cart
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/cart-pc02t
SKU: CART-PC02T
[email protected] www.vivo-us.com 309-278-5303
2
PACKAGE CONTENTS
WARNING!
A (x1)Base
B (x1)Keyboard Shelf
C (x1)Large Plastic
Sleeve
D (x1)Plastic Cover
E (x1)Clamp
Bracket
F (x2)Locking Caster
G (x2)Caster
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNINGSERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF CPU CART.
• USE TIPOVER RESTRAINT OR ANCHOR CART TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARDSMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
H (x1)VESA Mount
I (x1)CPU Holder
J (x1)Clamp
K (x1)Upper Pole
L (x1)Lower Pole
M (x1)Carriage Bolt
N (x3)Nut
O (x3)M6x6
P (x4)M6x12
Q (x2)M6x16
R (x2)M6x50
S (x5)Washer
T (x2)CPU Strap
U (x1)Mouse Pad
V (x1)Small Plastic
Sleeve
W (x2)Plastic
Sleeve Half
X (x2)Knob
Y (x2)Cable Clip
Z1 (x1)4mm Allen
Wrench
Z2 (x1)5mm Allen
Wrench
Z3 (x1)Wrench
M-A (x4)M4x12
M-B (x4)M4x16
M-C (x4)M5x12
M-D (x4)M5x16
M-E (x4)D5 Washer
M-F (x4)Spacer
3
ASSEMBLY STEPS
STEP 1Mount locking casters (F) and casters (G) to base (A). Locking casters (F) can be mounted to the rear (as shown) or front. Tighten with wrench (Z3).
STEP 2Assemble lower pole (L) to base using carriage bolt (M), washer (S) and nut (N). Secure with M6x12 screws (P) using 4mm Allen wrench (Z1), then slide plastic cover (D) over the top of the pole (L).
G
G
F
A
F Z3
L
DM
S
N
P Z1
17.6 lbs(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.Failure to do so may result in serious injury.
22 lbs(10kg)
MOUNT CPU
4.4 lbs(2kg)
KEYBOARD TRAY
4
STEP 3Remove the attached spacer from the lower end of Pole (K) and insert small plastic sleeve (V). Reattach spacer. Assemble upper pole (K) to lower pole (L) by aligning holes on the sides, and secure using long bolts (R), washers (S) and nuts (N). Tighten using 4mm Allen wrench (Z1) and crescent wrench (Z3).
STEP 4
Assemble clamp bracket (E) to CPU holder (I) using M6x6 screws (O) and 4mm Allen wrench (Z1).
STEP 5
Remove nuts from CPU holder (I) and separate halves. Set washers aside.
L
R SS N
V
K
L
I
OZ1
I
E
5
STEP 6Mount CPU holder (I) to lower pole (L) using clamp (J), plastic sleeve halves (W) and M6x16 screws (Q). The clamp MUST be assembled with plastic sleeve halves to properly secure to pole (L). Tighten with 4mm Allen wrench (Z1).
STEP 7
Clip large plastic sleeve (C) into pole mount bracket of keyboard tray (B) as shown. Slide keyboard tray (B) onto upper pole (K) and tighten with knobs on the back and side. Make sure the bump on (C) and the bolt hole on (B) are matched in alignment. Place mouse pad (U) on preferred side of tray (B).
STEP 8
Reassemble CPU holder using knobs (X) and previously removed washers. Thread “T” end of CPU straps (T) through slots in CPU holder (I) as shown, making sure the clips on the straps (T) are facing away from the center of the holder (I).
Q Z1JW
X
T
B
C
K
U
6
STEP 9Slide monitor VESA mount (H) onto pole and secure at desired height using 5mm Allen wrench (Z2). Attach cable clips (Y) to pole (K).
STEP 10
Remove top screw from monitor VESA mounting plate (H) using 4mm Allen wrench (Z1).
STEP 11
Adjust CPU holder (I) to fit the width of your CPU tower. Thread ends of CPU straps (T) through the inside of the slots, through the plastic clips, then through the security clips. Place CPU tower in holder (I), tighten straps (T), and lock in place with security clips. Slide lower cable clip down if desired.
H
Y
1
2
1
2
3
Z1
7
STEP 12Option A: Flat Back Monitor Mount VESA plate (H) to monitor using one of the screw (M-A or M-C) and/or washer (M-E) combinations shown.
STEP 13
Option B: Curved Back Monitor Mount VESA plate (H) to monitor using one of the screw (M-B, M-D)/washer (M-E)/spacer (M-F) combinations shown.
Slide monitor with VESA plate (H) onto monitor mount and secure with previously removed screw.
Adjust as Desired
M-E M-AM-C
M-EM-F
M-BM-D
Z1
Z2Z2
1
2
Z2 Z1
3
+15°
-15°
LAST UPDATED: 10/14/2019
Open Monday-Friday from 7:00am-7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within office hrs): 1HR 8M - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr
AVG. RESOLUTION TIME (within office hrs): 5M 4S
AVG. RESOLUTION TIME (within office hrs): < 15 M