bin trailers - northstar attachments...11. use a slow-moving-vehicle (smv) emblem when transporting....

BIN TRAILERS

MODEL 150

MODEL 165

MODEL 175

INTRODUCTION

Congratulations! Thank you for choosing Northstar. We are confident this equipment will meet your requirements in terms of quality, performance and reliability. This manual was prepared to assist you in the safe operation of your new Bin Trailer. It contains important information, which will help you achieve excellent returns for years to come. Please read this manual before operating your Bin Trailer and keep it for future reference. Before using this equipment, you or any other person who will be using it must familiarize yourself with the safety recommendations, the operating and safety instructions. Please read carefully and be sure to understand and follow all recommendations and procedures. If you require additional information on your Bin Trailer, please contact your Northstar Dealer.

SAFETY ALERT SYMBOL

NOW take a moment to enter the model, serial number and the date of purchase for your Bin Trailer in the space provided below. When ordering parts from your Dealer, please refer to these numbers for fast and efficient service. Use genuine Northstar parts for replacements. The model and serial numbers are located on the front of the Bin Trailer as shown below.

Model: _____________________________ Serial No.: __________________________ Date of Purchase: ____________________ BE ALERT TO THE POSSIBILITY OF PERSONAL INJURY.

THIS SYMBOL IDENTIFIES IMPORTANT SAFETY MESSAGES. CAREFULLY READ THE MESSAGE

THAT FOLLOWS.

Page 1

Be observant and safety minded. Recognize and correct or avoid hazardous conditions before an accident can happen. Practicing simple fundamental safety rules can prevent most accidents. 1. Read and understand the implement and tractor owner’s manuals before operating. 2. Be sure safety decals and reflectors are clean and in place. 3. Do not climb or walk on frames, or tires. 4. Never position yourself under any portion of implement unless entire unit is

supported by jacks. 5. Stop engine before leaving the operator’s position to adjust, lubricate, clean or

unclog the machine. 6. Do not stand between the implement and tractor unless the tractor brakes are locked

and engine is shut off. 7. Do not stand on or straddle a tongue when unhitching. 8. Never use machinery until all safety devices are in place. 9. Release all hydraulic pressure before shutdown periods. 10. Comply with Federal, State and local laws. 11. Use a Slow-Moving-Vehicle (SMV) emblem when transporting. 12. Always use a safety chain of tensile strength equal to the gross weight of the

implement and attachments when towing. 13. Towing vehicle weight must exceed weight of towed implement. 14. Check wheel bolts before and during transport. 15. Never permit riders on implement. 16. Never transport the Bin Trailer at a speed greater than suggested tire speed. 17. Keep small children away from farm equipment. 18. Inspect and tighten bolts daily as necessary.

Page 2

SAFETY/MAINTENANCE DECALS

The safety of the operator was a prime consideration in the design of the Northstar Bin

Trailer. Keep decals clean and replace them immediately if they are missing. Contact

your Dealer for replacements.

Page 3

WARRANTY

Northstar Attachments LLC expressly warrants each new Bin Trailer to be free from defects in material and workmanship under normal use and service for a period of one year after delivery to the original retail purchaser or first user of the product. Our obligation under this warranty is limited to repairing and/or replacing, at our option, any part or parts within the applicable one year period, as set out above, which shall be returned by the owner to any Northstar authorized dealer or to the factory and which upon examination shall disclose to our satisfaction to be defective.

We may, as an option, elect to grant adjustments in the field through an authorized representative and may thereby elect to waive the requirement that parts be returned to our factory. A new warranty period is not established for replacements. Replacements are warranted for the remaining portion of the one-year original warranty period. The repair or replacement of defective parts under this warranty will be made without charge to the owner except for transportation. Warranty does not cover tires, hydraulic valves, hydraulic cylinders, electric switches, or accessories and other parts not manufactured by us but supplied with or as a part of our product. We will, however, obtain and pass on any adjustments provided by the manufacturers of such parts under those manufacturer’s warranties. The provisions of this warranty do not apply to any product or parts, which have been subject to misuse, negligence or accident, or which have been repaired or altered outside of an authorized dealer in any way so as in the judgment would adversely affect its performance and reliability. Neither does this warranty apply to normal maintenance service and parts, or to normal deterioration due to wear and exposure.

Page 4

MAINTENANCE

DAILY

1. Visually check for loose fasteners.2. Grease tongue pivot pins liberally. Lubricate chain as needed.3. Grease 2" ball.

WEEKLY

1. Check for loose sprockets. Retighten if necessary.2. Tighten main pick-up chain if necessary. Note: if tightening is necessary, the short

drive chain must be loosened first and then retightened. Also replace the chain guard.3. Grease drive shaft bearings. Note: grease only until bearing will not accept any more.

To further pump grease into sealed bearings damages the seals.

AFTER FIRST 100 HOURS

1. Check for loose fasteners. (If necessary use torque chart provided below.)2. Check ground skids for excessive wear.3. Check 2" ball and coupler for excessive wear.4. Check idler sprockets for damaged bearings.

TORQUE CHART

Torque Specification Table

Thread UNC and UNF Grade 2 Grade 5 Grade 8* BOLT SIZE TORQUE TORQUE TORQUE

Pound Feet Pound Feet Pound Feet Inches mm Min Max Min Max Min Max

¼ 6.25 5 6 9 11 12 155/16 7.94 10 12 17 20.5 24 293/8 9.53 20 23 35 42 45 54

7/16 11.11 30 35 54 64 70 84½ 12.70 45 52 80 96 110 132

9/16 14.29 65 75 110 132 160 1925/8 15.88 95 105 150 180 220 264¾ 19.05 150 185 270 324 380 456

7/8 22.23 160 200 400 480 600 7201 25.40 250 300 580 696 900 1080

1-1/8 25.58 - - 800 880 1280 1440 1-1/4 31.75 - - 1120 1240 1820 2000 1-3/8 34.93 - - 1460 1680 2380 2720 1-1/2 38.10 - - 1940 2200 3160 3560

* Thick nuts must be used with grade 8 bolts.

Page 5

HYDRAULIC SYSTEMS

HYDRAULIC CONNECTION: Your Bin Trailer is supplied with Safeway or Pioneer tips. These will attach to most tractor hydraulic systems. Contact your Northstar Attachments Dealer if other style of tips are necessary. (Note: always clean tips of dirt and oil before installing.) The hydraulic valve is set to operate with an open center hydraulic system. If your tractor has a closed center system, you will need to replace plug @ ‘A’ as shown below. ) The closed center plug is not supplied with your Bin Trailer.) Failure to change to a closed center

system will cause damage to your tractor hydraulic system.

HYDRAULIC OPERATION: Your Bin Trailer is operated with a 2 function or 3 function valve. Handles 1 and 2 are for tilting of Bin Trailer and lowering of the axle. Handle 3 is for operating the pick-up chain. This function is supplied with a detent position that allows the operator to fully engage the pick-up chain while tilting or lowering the Bin Trailer. Note: while operating your Bin Trailer, you experience the inability to fully pick-up the fourth bin, you may need to adjust the hydraulic pressure @ ‘B’. (Remove the acorn nut and turn screw clockwise one turn for every 300 PSI. Your tractor will only produce about 2200PSI and the valve is factory set at 1500PSI.) If this does not correct the problem, your tractor may not have enough hydraulics to operate the Bin Trailer properly.

Page 6

ITEM QTY PART NO DESCRIPTIONREF TR-806 Cross 2 Spool Valve Assembly for TR-150REF TR-859 Cross 3 Spool Valve Assembly for TR-165 & TR-175

1 3 TR-834 1V1703 Cross Handle2 3 TR-835 1V1701 Pin Kit3 3 TR-833 4Z4306 Handle Bracket4 6 TR-869 2A0283 2-214 O-Ring4.5 6 TR-809 O-Ring Spool Washer5 1 TR-805 1V0294 Detent Kit6 3 TR-659 1A0294 End Cap7 3 N/A 1V0090 Spool8 1 TR-820 2A0354 SAE Plug (Open Center)

REF TR-807 1V0206 Closed Center Plug (not shown)9 2 TR-1A0294 1A0294 Stop Collar10 2 TR-1A9008 1A9008 Heavy Centering Spring11 1 TR-1R0017 1R0017 Relief Assembly12 12 N/A Socket Head Cap Screw, 1/4"-20 x 3/4"13 7 N/A Socket Head Cap Screw, 1/4"-20 x 1/2"

CROSS VALVE ASSEMBLY

* Seal Kits Not Available - Only TR-869 O-Ring

Page 7

1

2

3

4

4

4

5

6

6

7

8

9

11

10

4.5

4.5

4.5

12

13

13

12

CRO

SS V

ALV

E A

SSEM

BLY

Page 8

ITEM QTY PART NO DESCRIPTION1 1 TR-737 Turnbuckle2 1 TR-2735 RH Thread Rod and Eye Turnbuckle3 1 TR-734 Bronze Bushing4 1 TR-732-RH Right Hand Actuator ArmREF 1 TR-732-LH Left Hand Actuator Arm (not shown)5 1 TR-738 Pivot Block6 1 TR-723 Spring7 1 TR-702 ½ Chain Link8 1 TR-2738 Slide Bushing Front9 1 TR-2738-1 Slide Bushing Rear10 1 TR-2736 LH Thread Rod & Eye Turnbuckle (TR-165 only)REF 1 TR-2736-175 LH Thread Rod & Eye Turnbuckle (TR-175 only) (not shown)11 1 TR-731-RH Right Hand Bin Stop EarREF 1 TR-731-LH Left Hand Bin Stop Ear (not shown)12 1 TR-733 Pivot Pin13 1 TR-780 3/16" x 1-1/2" Cotter Pin14 1 TR-667 3/4" SAE Flat Washer15 1 TR-666 3/4" NC x 3" HHCS Gd. 516 1 G-5-2.75NCCS 1/2" x 2 3/4" HHCS Gd. 517 4 G-5SAEFW 1/2" SAE Flat Washer18 1 G-5NCHGN 1/2" Hex Grip Nut

PART NO DESCRIPTIONTR-2737-RH Standard Right Hand Kit for TR-165 TrailerTR-2737-LH Standard Left Hand Kit for TR-165 TrailerTR-2747-RH Extended Right Hand Kit for TR-175 TrailerTR-2747-LH Extended Left Hand Kit for TR-175 Trailer

BIN STOP ASSEMBLY

BIN STOP KIT ASSEMBLY NUMBERS

Page 9

1

2

3

3

4

5

6

7

8

9 10

11

12

13

1414

14

14

15

16

1718

17

17

BIN

LO

CK

ASS

EMBL

YTR

-273

7 &

TR-

2748

Page 10

ITEM QTY PART NO DESCRIPTION1 1 TR-2100 Main Frame Weldment - 32" Frame

TR-2110 Main Frame Weldment - 30" Frame2 1 TR-2102-A Tongue Weldment (2008 & Later)

TR-2102 Tongue Weldment (Pre 2008) (not shown)3 2 TR-500-1 Chain Guard (2008 & Later)

TR-500 Chain Guard (Pre 2008) (not shown)4 1 TR-2115 Motor Guard5 1 TR-2536 Hydraulic Cylinder Anchor6 1 TR-830 3512 Hydraulic Cylinder

REF TR-889 3512 Spencer Hyd. Cylinder Seal Kit (639577) (not shown)REF TR-774 3512 Cross Hyd. Cylinder Seal Kit (1C4429) (not shown)

7 2 TR-827 Hydraulic Cylinder Pin8 1 TR-2598 Hose Ring9 1 TR-2597 Hose Bracket10 1 TR-1134 2" Bulldog Coupler - 3" Tube

1 TR-797 Bulldog Coupler Locking Pin (not shown)TR-1132 2" Bulldog Coupler – 2-1/4" Tube (not shown)

11 1 TR-847 5/16" Safety Chain12 1 TR-2715-A 1" Tongue Pin 17-1/4" Long (2008 & Later)

TR-2715 1" Tongue Pin 16-5/8" Long (Pre 2008) (not shown)1 TR-670 1" SAE Flat Washer (not shown)1 TR-671 1/4" x 2" Cotter Pin (not shown)

13 1 TR-2915-RH Right Hand Tongue Bushing14 1 TR-2915-LH Left Hand Tongue Bushing15 1 TR-792 Bulldog Jack

OPT TR-2168 Jack Stand (not shown)OPT TR-783 5/16" PTO Pin (not shown)

16 1 TR-314 1-7/16" Drive Shaft - 32" FrameTR-315 1-7/16" Drive Shaft - 30" Frame (not shown)TR-311 1-7/16" Drive Shaft - 36" Frame (not shown)

17 1 TR-313 1-7/16" 60B16 Drive Sprocket18 1 TR-576 3/8" Keystock – 1-1/4" Long19 2 TR-815 1-7/16" Pillow Block Bearing20 2 TR-2151 1-7/16" 60C20 Drive Sprocket21 2 TR-577 3/8" Keystock - 2" Long22 1 TR-804 Char-Lynn Motor – 104-1027

REF TR-832 Char-Lynn Motor Seal Kit (not shown)23 1 TR-574 5/16" Keystock24 1 TR-2125 Hydraulic Motor Bracket25 1 TR-801 #60 Chain - 30"

1 TR-802 #60 Chain Conn Link (not shown)26 1 TR-312 1-1/4" 60B16 Drive Sprocket27 2 TR-131 Chain Tension Adjustment Screw28 2 TR-800 2060H Chain - 34'6" Long

2 TR-803 2060H Conn Link (not shown)29 2 TR-1152 Chain Idler Sprocket30 2 TR-1102 Pin Assy. – Idler Sprocket31 2 TR-785 9.5L 15 Tire – 8ply32 2 TR-779 Flex Axle Hub 6 on 6 Complete w/Races, Bearings, Seal, Cap and Lug Nuts

TR-810 Fixed Axle Hub 6 on 6 Complete w/Races, Bearings, Seal, Cap and Lug Nuts (not shown)33 2 TR-784 Seal #SL225-1 (1998 & Later)

TR-775 Seal #10-1 (Pre 1998) (not shown)34 2 TR-776 25580 Inner Bearing35 2 TR-777 25520 Inner Race36 2 TR-839 LM67010 Outer Race37 2 TR-838 LM67048 Outer Bearing38 2 TR-672 1" Washer39 2 TR-673 1" NF Slotted Nut40 2 TR-674 1/8" x 1-1/2" Cotter Pin41 2 TR-778 21-1 Grease Cap42 2 TR-812 15" x 7 Wheel43 12 TR-799 9/16" NF Lug Bolt44 1 TR-806 Cross 2 Spool Valve45 1 TR-1139 Cross 2 Spool Valve Stand46 2 TR-791 Axle Spindle - Weld on Replacement47 2 TR-501 Skid Plate - Weld on Replacement48 2 TR-105 Chain Guide Pair - Weld on Replacement

TR-106 Keystock, 7/16" -- 12' length - Weld on Replacement (Requires 3 per Trailer) (not shown)

TR-150 BIN TRAILER ASSEMBLY

Page 11

1

2

3

4

5

6

7

8 9

1011

12

13

14

15

16

1718

1920

21

2223

24

25

26

27

28

2930

31

32

33

34

35

36

37

38

39

40

41

42

43

44

4546

47

48

TR-1

50 B

IN TR

AIL

ER A

SSEM

BLY

Page 12


TR-2108 Main Frame Weldment - 30" Frame (not shown)2 1 TR-2102-A Tongue Weldment (2008 & Later)


TR-500 Chain Guard (Pre 2008) (not shown)4 1 TR-2115 Motor Guard 5 1 TR-2536 Hydraulic Cylinder Anchor6 1 TR-830 3512 Hydraulic Cylinder



1 TR-797 Bulldog Coupler Locking Pin (not shown)TR-1132 2" Bulldog Coupler – 2-1/4" Tube (not shown)







REF TR-832 Char-Lynn Motor Seal Kit23 1 TR-574 5/16" Keystock24 1 TR-2125 Hydraulic Motor Bracket25 1 TR-801 #60 Chain - 30"

1 TR-802 #60 Chain Conn Link (not shown)26 1 TR-312 1-1/4" 60B16 Drive Sprocket27 2 TR-131 Chain Tension Adjustment Screw28 2 TR-800 2060H Chain - 34'6" Long

2 TR-803 2060H Conn Link (not shown)29 2 TR-1152 Chain Idler Sprocket30 2 TR-1102 Pin Assy. – Idler Sprocket31 2 TR-857 308DB Hydraulic Cylinder

REF TR-871-S 308DB Spencer Hydraulic Seal Kit (639575) (not shown)REF TR-871 308DB Cross Hydraulic Seal Kit (1C4147) (not shown)

32 2 TR-432 Axle Tie Bar33 4 TR-431 Link Pin

8 TR-780 3/16" x 1-1/2" Cotter Pin (not shown)34 4 TR-867 20.5 x 8 x 10 Tire & Wheel Assy.35 4 TR-883 Hub 5 on 4-1/2" Complete w/Races, Bearings, Cap, Seal and Lug nutsREF 10 TR-887 Hub Stud - Dexter (G-7-122) (not shown)36 4 TR-878 SL173 Grease Seal37 4 TR-879 L68149 Inner Bearing38 4 TR-880 L68111 Inner Race39 4 TR-882 L44610 Outer Race40 4 TR-881 L44649 Outer Bearing40 *4 3164 L44643 Outer Bearing (not shown) SERIAL# 11217 & Greater41 4 TR-672 1" Washer41 4 TR-161119 "D" Washer (not shown)42 4 TR-673 1" NF Slotted Nut42 4 TR-161121 1" Jam Nut (not shown)43 4 TR-674 1/8" x 1-1/2" Cotter PinREF 4 TR-161120 Spindle Nut Retainer (not shown)44 4 TR-877 E-Z Lube Grease Cap w/ rubber plug (not shown)44 4 TR-884 Sure Lube Grease Cap (not shown)45 4 TR-866 10" x 6" Wheel – 5 on 4-1/246 20 TR-896 1/2" Lug Nut47 1 TR-859 Cross 3 Spool Valve

TR-897 Brand 3 Spool Valve (not shown)48 1 TR-1140 Cross 3 Spool Valve Stand

TR-1138 Brand 3 Spool Valve Stand (not shown)49 4 TR-675 3/8" Hose Clamp Complete51 1 TR-2430F 3500lb Axle Weldment - Front - 32" Frame

TR-2430FN 3500lb Axle Weldment - Front - 30" Frame52 1 TR-2430R 3500lb Axle Weldment - Rear - 32" Frame

TR-2430RN 3500lb Axle Weldment - Rear - 30" Frame16 TR-437 3/16" x 3/4" x 5" UHMW Axle Pivot Bearing (not shown)

53 2 TR-501 Skid Plate - Weld on Replacement54 2 TR-105 Chain Guide Pair - Weld on Replacement

TR-106 Keystock, 7/16" -- 12' length - Weld on Replacement (Requires 3 per Trailer) (not shown)55 1 TR-161171 Axle Cylinder Transport Lockout56 1 P71111 Hitch Pin - 1/2"57 1 P771 Tongue Transport Lockout Pin58 1 P791 Lynch Pin


* Parts for Trailers-Serial# 11217 & Greater

Page 13

1

2

3

4

5

6

7

8 9

1011

12

13

14 15

16

17

18

1920

21

2223

24

25

26

27

28

2930

31

3233

34

35

3637

38

39

40

4142

4344

45

46

47

48

52

51

53

54

49

49

55

57

56

58

TR-1

65 B

IN TR

AIL

ER A

SSEM

BLY

Page 14

ITEM QTY PART NO DESCRIPTION1 1 TR-2107-32RA Mainframe, 32" Wide (Model TR-16532RA)REF TR-2107-30RA Mainframe, 30" Wide (Model TR-16530RA) (not shown)REF TR-2107-32RAL Mainframe, 32" Wide, Tapered Tips (Model TR-16532RAL) (not shown)REF TR-2107-30RAL Mainframe, 30" Wide, Tapered Tips (Model TR-16530RAL) (not shown)2 1 TR-2430RA-F Standard Front Axle Assembly (Models - TR-16532RA & TR-16532RAL)REF TR-2430RAL-F Narrow Front Axle Assembly (Models - TR-16530RA & TR-16530RAL) (not shown)3 1 TR-2430RA-R Standard Rear Axle Assembly (Models - TR-16532RA & TR-16532RAL)REF TR-2430RAL-R Narrow Rear Axle Assembly (Models - TR-16530RA & TR-16530RAL) (not shown)4 4 TR-435-C Axle Clamp BracketREF 4 TR-435-B Weld On Axle Clamp Plate (not shown)5 32 N/A HHCS, 1/2"-13 x 1 3/4" NC Gr. 56 32 N/A SAE Flat Washer, 1/2"7 32 N/A Lock Washer, 1/2"8 32 N/A Hex Nut, 1/2"-13

TR-165 REMOVEABLE AXLE ASSEMBLYMODELS: TR-16532RA, TR-16530RA, TR-16532RAL, TR-16530RAL

Page 15

3

2

1

45

6

78

TR-1

65 R

EMO

VEA

BLE

AXL

E A

SSEM

BLY

MO

DEL

S: T

R-16

532R

A, T

R165

30RA

, TR-

1653

2RA

L, T

R-16

530R

AL

Page 16


TR-2109 Main Frame Weldment - 30" Frame (not shown)2 1 TR-2102-A Tongue Weldment (2008 & Later)


TR-500 Chain Guard (Pre 2008) (not shown)4 1 TR-2115 Motor Guard5 1 TR-2536 Hydraulic Cylinder Anchor6 1 TR-830 3512 Hydraulic Cylinder



1 TR-797 Bulldog Coupler Locking Pin (not shown)TR-1132 2" Bulldog Coupler – 2-1/4" Tube







REF TR-832 Char-Lynn Motor Seal Kit23 1 TR-574 5/16" Keystock24 1 TR-2125 Hydraulic Motor Bracket25 1 TR-801 #60 Chain - 30"

1 TR-802 #60 Chain Conn Link26 1 TR-312 1-1/4" 60B16 Drive Sprocket27 2 TR-131 Chain Tension Adjustment Screw28 2 TR-857 308DB Hydraulic Cylinder

REF TR-871-S 308DB Spencer Hydraulic Seal Kit (639575) (not shown)REF TR-871 308DB Cross Hydraulic Seal Kit (1C4147) (not shown)

4 TR-780 3/16" x 1-1/2" Cotter Pin (not shown)29 2 TR-800 2060H Chain - 34'6" Long

2 TR-803 2060H Conn Link30 2 TR-1152 Chain Idler Sprocket31 2 TR-1102 Pin Assy. – Idler Sprocket32 2 TR-785 9.5L 15 Tire – 8ply33 2 TR-779 Flex Axle Hub 6 on 6 Complete w/Races, Bearings, Seal, Cap and Lug Nuts34 2 TR-784 Seal #SL225-1 (1998 & Newer)

TR-775 Seal #10-1 (Pre 1998) (not shown)35 2 TR-776 25580 Inner Bearing36 2 TR-777 25520 Inner Race37 2 TR-839 LM67010 Outer Race38 2 TR-838 LM67048 Outer Bearing39 2 TR-672 1" Washer40 2 TR-673 1" NF Slotted Nut41 2 TR-674 1/8" x 1-1/2" Cotter Pin42 2 TR-778 21-1 Grease Cap43 2 TR-812 15" x 7 Wheel44 12 TR-799 9/16" NF Lug Bolt45 1 TR-859 Cross 3 Spool Valve46 1 TR-1140 Cross 3 Spool Valve Stand47 2 TR-2402 Pivot Bracket48 1 TR-2790 Torflex Axle Assy. - 32" Frame

TR-2790N Torflex Axle Assy. - 30" Frame49 8 TR-795 UHMW Wear Strip50 4 TR-675 3/8" Hose Clamp Complete52 2 TR-791 Axle Spindle - Weld on Replacement53 2 TR-501 Skid Plate - Weld on Replacement54 2 TR-105 Chain Guide Pair - Weld on Replacement

TR-106 Keystock, 7/16" -- 12' length - Weld on Replacement (Requires 3 per Trailer) (not shown)


Page 17

1

2

3

4

5

6

7

8 9

1011

12

13

14 15

16

17

18

1920

2122

23

24

25

26

27

2829

3031

32

33

34

35

36

37

38

39

4041

42

43

44

45

46

47

48

4952

53

54

50

50

TR-1

75 B

IN TR

AIL

ER A

SSEM

BLY

Page 18

ITEM QTY PART NO DESCRIPTION1 1 TR-2171-1 Walking Beam Assy.2 2 TR-867 20.5 x 8 x 10 Tire & Wheel Assy.3 2 TR-883 Wheel Hub – 5 on 4-1/2" Complete w/Races, Bearings, Seal, Cap & Lug Nuts4 2 TR-878 SL173 Grease Seal5 2 TR-879 LM68149 Inner Bearing6 2 TR-880 LM68111 Inner Race7 2 TR-882 L44610 Outer Race8 2 TR-881 L44649 Outer Bearing9 2 TR-672 1" Washer10 2 TR-673 1" NF Slotted Nut11 2 TR-674 1/8" x 1-1/2" Cotter Pin12 2 TR-877 21 – 3 Grease Cap

REF TR-884 Sure Lube Grease Cap (not shown)13 10 TR-896 1/2" NF Lug Nut14 12 TR-668 1/2" SAE Flat Washer15 12 TR-669 9/16" NF x 2" HHCS Gd. 5

TR-2170 WALKING BEAM ASSEMBLY

Page 19

1

2

3

45

6

78

910

11

12

13

1415

TR-2

170

WA

LKIN

G B

EAM

ASS

EMBL

Y

Page 20

TR-2

915-

LH

TR-2

102-

A

TR-2

715-

A

TR-2

915-

RH

*TR-

530-

A

*TR-

707-

A

*TR-

713-

A*T

R-71

4

*TR-

716

*REP

LAC

EMEN

T PA

RTS

ARE

WEL

D O

N O

NLY

BIN

TRA

ILER

TON

GUE

REP

LAC

EMEN

T PA

RTS

REFE

REN

CE

2008

& L

ATE

R M

ODE

LS

Page 22

ITEM QTY PART NO DESCRIPTION1 1 TR-2719 Right Hand Mounting Bracket

1 TR-2720 Left Hand Mounting Bracket2 2 TR-718 Mounting Plate3 2 TR-2740 Vulcanized Roller4 4 TR-769 1" Flange Bearing5 2 TR-693 H60BS15 Sprocket6 2 TR-695 1" Drive Shaft7 2 TR-691 1/4" Keystock 2 5/8" Long8 2 TR-692 1/4" Keystock 1 1/4" Long9 4 G-4375-1.25NCCB 7/16" x 1 1/4" USS Carriage Bolt10 8 G-4375LW 7/16" Lock Washer11 4 G-4375NCHN 7/16" Hex Nut12 4 G-4375-1.5NCCS 7/16" x 1 1/2" USS Gr. 5 Cap Screw

RUBBER DRIVE ROLL ASSEMBLY

Page 23

THESE PARTS ARE NLA

1

2

3

4

5

6

7

8

9

1011

12

10

RUBB

ER D

RIVE

RO

LL A

SSEM

BLY

Page 24

THESE PARTS ARE NLA

ATTACHMENTS, LLC

3205 Bay Street Union Gap, WA

98903

P.O. Box 1937 Yakima, WA 98907-1937

Phone: (509) 452-1651

Fax: (509) 457-6601

Updated 4.13.2021

bin trailers - northstar attachments...11. use a slow-moving-vehicle (smv) emblem when transporting....

Documents